RA2 Installation Manual Rev. B
|
|
- Arabella Pitts
- 5 years ago
- Views:
Transcription
1
2
3 Important Information Required Installation Tools Voltmeter Wire Strippers Electric Drill & Bits Phillips Screwdriver Convoluted Tubing * Solder Gun * Wire Crimpers Shrink Tube or Electrical Tape * Optional Recommended Procedures 1. Test all circuits with a voltmeter. 2. Make all wiring connections with butt connectors or solder. DO NOT twist wires or use "scotch-lok" type connectors. 3. Route RED, RED/WHITE and BLACK wires from the control unit directly to the battery. 4. Keep extensions as short as possible. Use same gauge wires for short extensions and larger gauge wires for longer extensions. 5. Before installing, discuss the placement of the LED indicator and valet switch with the vehicle owner. 6. DO NOT disconnect the battery cables. Make all connections by removing the lug from the cable clamp without detaching the clamp. 7. Turn off dome light or remove dome light fuse to prevent battery drain. This device com plies with Part 15 of the FCC rules. Any changes or modifications made to the system with out the express approval of Avital Technologies, Inc. could void the user s authority to operate this equipment. 1
4 Main Wiring Diagram 2
5 Installation Procedures Control Unit 1. Select a location under the dash that will allow you to use tie wraps to securely fasten the control unit. 2. Mount the control unit as high as possible to ensure maximum range. 3. Do not mount the control unit near moving parts. 4. Avoid areas that are in the direct path of air blowing from the vents. 5. Route wires from this point, leaving slack for ease of service. Antenna 1. Do not shorten or lengthen the antenna. 2. Route the antenna away from the control unit. 3. Keep the antenna as far away from metal and wire harnesses as possible to optimize range. Wireloom 1. Plug the wireloom securely into the control unit. 2. Route wires from the control unit directly to each connection point. 3. Separate the RED, RED/WHITE and BLACK wires. 4. Sleeve these wires with vinyl tubing or electrical tape and route them through an existing rubber grommet into the engine compartment. 5. Use tie wraps to fasten wires to existing vehicle wire harnesses. Valet Switch 1. Discuss placement with the owner. 2. Choose a location for the valet switch that is hidden, but convenient for the owner to access. 3. Drill a ¼" hole and mount the switch. 4. Route the valet switch wires to the control unit. 5. Plug the valet switch WHITE connector into the control unit WHITE plug. 3
6 LED Indicator 1. Discuss placement with the owner. 2. Choose a location that is visible from both sides of the vehicle. 3. Drill a ¼" hole. 4. Route the LED wires through the hole and press LED into place. 5. Route the LED wires to the control unit. 6. Plug the RED LED connector into the control unit RED plug. LED Off On solid Slow flash Rapid flash Status System is disarmed In Protected Valet Mode System is armed Passive arming Ignition In put 1. Use a voltmeter to locate the one wire that shows +12 volts when the ignition key is in the "ON," "CRANK" and "RUN" position and 0 volts when the ignition key is in the "OFF" position. 2. Connect the control unit PINK wire to the vehicle ignition wire. Parking Lights 1. If the parking lights are positive trigger, connect the RED/WHITE wire to the battery positive (+) terminal through the 20 amp fuse. NOTE: Do not connect the RED/WHITE wire to the control unit RED wire. 2. If the parking lights are negative (-) trigger, connect the RED/WHITE wire to control unit BLACK wire. 3. Connect the RED/BLACK wire to the vehicle parking light wire. Channel #3 Accessory Output (Trunk Button) The DARK BLUE wire provides a 0.75 second ground (-) output when momentarily activated for 1-2 seconds. If the remote control button is continuously pressed, the signal will stay at ground as long as the button is held. Most trunk releases are positive and require an optional relay. 4
7 Channel #4 Programmable Timed Accessory Output (Op tion Button) The LIGHT BLUE wire can be programmed to provide a (-) output from 1 second to 2 minutes. This output can be used to activate headlights, operate motorized amp racks, roll-up/down windows and close sun roofs on vehicles equipped with factory "all-close." I CAUTION : Do not use this output to roll-up windows on vehicles not equipped with "all-close." Channel #5 Programmable Pulse/Latched Accessory Output (Lock and Unlock But tons) See "Programming Table for System Features." The BLUE/YELLOW wire can be programmed to provide a 0.75 second momentary output or a continual latched output. This output can be used to turn on radio equipment and neon or any other momentary or latch activated accessory. Pulse Press the LOCK and UNLOCK buttons simultaneously. The BLUE/YELLOW wire provides a 0.75 ground output. Latched To activate, press the LOCK and UNLOCK buttons simultaneously. The BLUE/YELLOWwire will provide a continual ground output. To deactivate, press the LOCK and UNLOCK buttons simultaneously. I CAUTION: In the latched mode, the accessory you are activating may be drawing enough current to drain the battery. Be sure to deactivate before leaving the vehicle unattended for long periods of time. 5
8 Optional Starter Disable The GRAY wire provides a continual ground output when the doors are remotely locked or if Passive Starter Disable is programmed ON. A 30 amp relay is needed to disable the starter. We recommend that the starter wires be soldered and shrink tubed. 1. Locate the ignition switch wireloom under the dash board. 2. Use a voltmeter to find the one wire that shows +12 volts only while the ignition key is in the cranking cycle only. This is the starter solenoid wire. 3. Cut the starter solenoid wire. Test by trying to crank the starter with the ignition key. If it will not crank, you have the correct wire. 4. Connect one end of the starter solenoid wire to the relay terminal 87A. 5. Connect the other end of the starter solenoid wire to the relay terminal Connect relay terminal 86 to the control unit PINK wire. 7. Connect relay terminal 85 to the control unit GRAY wire. Interior Light Illumination The system s door trigger will accept a positive or negative input. When the system is remotely unlocked, the interior lights will turn on for 30 seconds or until the ignition key is turned on. 1. Connect the control module WHITE wire to the vehicle door trigger wire(s). 2. If the door trigger is negative switching, connect the control module WHITE/BLACK wire to ground. 3. If the door trigger wire is positive switching, connect the control module WHITE/BLACK wire to a constant fused +12 volt source. Optional Siren/Horn Honk The VIOLET (-) output wire can be programmed for a siren (continual) output or horn (pulse) output. This output can be used for remote panic and Audible Lock/Unlock Confirmation. (See "Programming Table for System Features" on page 12.) Door Locks The AMX38 system has a built in two-stage unlocking capability as well as selectable positive or negative lock/unlock outputs. Reverse polarity type door locks require optional relays. (Refer to the Door Lock Diagrams on pages 7-10.) 6
9 7
10 8
11 9
12 10
13 Programmable Features All system and remote control programmable features are accomplished by turning the ignition key to the "ON" position or starting the engine and flicking the valet switch on and off a preset number of times. The built-in piezo beeper will beep for audible programming confirmation. The system also allows the user to add new remote controls in one step, delete lost or stolen remote controls or rearrange the factory preset remote control functions. 1. Remove the system from Protected Valet Mode. Programming cannot be accessed while the system is in Protected Valet Mode indicated by the LED on solid red. 2. Select the feature you wish to program from the "Programming Table for System Features" or the "Programming Table for Remote Controls" on pages 12 and 13. Note the number of beeps associated with that feature. 3. Turn the ignition key to the "ON" position. 4. Within 10 seconds, begin flicking the valet switch on and off. The built-in piezo beeper will beep once each time you flick the switch on then off. 5. Continue flicking the switch on and off, counting the number of beeps. NOTE: Stop when you reach the number of beeps associated with your chosen feature. 6. Follow the "Secondary Action." You will hear a number of beeps to confirm that you have changed the setting of that feature. 7. Turn the ignition key "OFF." 8. Repeat steps 1-7 for any other feature you wish to program. 11
14 Programming Table for System Features Fea ture Fac tory Set ting # of Beeps Sec on dary Action Ignition Control Lock/Unlock Lock/Unlock Output Duration (1-3 seconds) ON 4 1 Second 5 for OFF, twice for ON. for 3 seconds, twice for 1 second. 2 Pulse Unlock 1 Pulse 6 for 2 pulses, twice for 1 pulse. Siren (Continual) Horn (Pulse) Output Horn 7 for siren (continual), twice for horn (pulse). Illuminated Exit ON 8 Passive Starter Disable OFF 9 Passive Door Lock OFF 10 for OFF, twice for ON. for OFF, twice for ON. for OFF, twice for ON. Timed Accessory Output (1 second to 2 minutes) Pulse/Latched Accessory Output Audible Lock/Unlock Confirmation 1 Second 11 Pulse 12 OFF 13 to indicate the timer has started. Turn the ignition key off after your chosen duration. Example: if you want a 5 second duration, turn the ignition off 5 seconds after the beep. for latched, twice for pulse. for OFF, twice for ON. 12
15 Programming Table for Re mote Controls Feature Fac tory Set ting # of Beeps Sec on dary Action Door Lock LOCK Button 14 Press the LOCK button. The system will beep once for learned confirmation. Door Unlock UNLOCK Button 15 Press the UNLOCK button. The system will beep twice for learned confirmation. Trunk Release Output TRUNK Button 16 Press the TRUNK button. The system will beep 3 times for learned confirmation. Timer Accessory Output OPTION Button 17 Press the OPTION button. The system will beep 4 times for learned confirmation. Pulse/Latched Accessory Output LOCK and UNLOCK 18 Press the LOCK and UNLOCK buttons. The system will beep 5 times for learned confirmation. One-Step Remote Code Learning 19 Press the LOCK button. The system will beep once. The remote will operate at factory preset order. Instant Code Deletion 20 Wait 3 seconds. The system will beep twice. All remote controls are erased from memory. 13
16 1999 Avital Technologies, Inc. Part Number Rev. B
Manual - Inside Front Cover (Blank)
FRONT COVER Manual - Inside Front Cover (Blank) Table of Contents Important Information... 2 Recommended Installation Tools... 2 Recommended Procecures... 2 Wiring Diagram... 3 14 Pin Connector...4 Installation
More informationDiablo 2 /AMX 68/AT-58 Installation Manual 3/31/99
1 Table of Contents Required Installation Tools... 2 Important Information... 2 Wiring Diagram.... 3 14 Pin Con nec tor... 4 Starter Dis able Relay...4 Installation Procedures...5 Control Unit... 5 Antenna...
More informationAviStart 6500 Installation Manual
Table of Contents Important Information... 1 Recommended Installation Tools... 1 Recommended Procedures... 1 Main Wiring Diagrams.... 2 Pin Connectors... 5 Installation Procedures...7 Control Unit... 7
More informationAviStart 3000 Installation Manual
Table of Contents Important Information... 2 Recommended Installation Tools... 2 Recommended Procedures... 2 Main Wiring Diagram... 3 12 Pin Connector... 4 6 Pin Connector... 4 Installation Procedures...5
More informationAviStart 3001 Installation Manual, Revision B
Table of Contents Important Information........................... 1 Recommended Installation Tools.................... 1 Recommended Procedures....................... 1 14 Pin Connector............................
More informationMaxx 3 Installation Guide
Maxx 3 Installation Guide 2002 Directed Electronics, Inc. Vista, CA N840003 4-02 Table of Contents Important Information....................................................... 3 System Components........................................................
More informationINSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit
R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;
More informationAviStart 4000 Owner s Manual -FRONT COVER
AviStart 4000 Owner s Manual -FRONT COVER I WARNING I! Always exercise caution and common sense when operating your AviStart system.! This product is intended for vehicles with fuel-injection and automatic
More informationCovers All 430, 440, 441 and CJ Series Advanced Security Systems.
INSTALL GUIDE Covers All 430, 440, 441 and CJ Series Advanced Security Systems www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com FCC/ID Notice This device complies with
More informationCP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM
CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION
More informationREC-11+ REMOTE RECEIVER UNIT
Resetting The Programmable Features The installer may quickly and easily return all 17 programmable features back to the factory settings. Changing individual features were explained in detail in the previous
More information2 Way Security and Keyless Entry Installation Guide ca 1553
PROFESSIONAL SERIES 2 Way Security and Keyless Entry Installation Guide ca 1553 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationVS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1
VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 2 INSTALLATION We recommend insulating all your soldered or crimped connections
More informationModel APS-101N Installation Manual
Programmable Features Model APS-101N Installation Manual Select By Operating Transmitter Press Lock Button Press Unlock Button Siren Indications 1 Chirp 2 Chirps Factory Default 1) Arming Method Passive
More informationINSTALLATION MANUAL. Remote Mobile Security System. Model: PL30
Remote Mobile Security System INSTALLATION MANUAL Model: PL30 Copyright 1998 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be
More informationSERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL
SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location
More informationINSTALLATION MANUAL. Remote Mobile Security System. Model: PL50
Remote Mobile Security System INSTALLATION MANUAL Model: PL50 Copyright 2000 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be
More information6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM
6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM Button 1 Button 2 Button 5 Button 3 Button 4 Standard Features: Two 5-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren
More informationCS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM
INTRODUCTION: CS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Remote Keyless Entry System by Crimestopper Security Products Inc.
More informationINSTALLATION GUIDE. FCC ID NOTICE
REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This
More informationINSTALLATION MANUAL. Model: PLUS Vehicle Security
R Vehicle Security INSTALLATION MANUAL Model: PLUS-5000 Copyright 1999 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be a Registered
More informationCSI-300 Installation Instructions
CSI-300 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationMEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM. White. H1 5 Pin White. H6 2 Pin White.
MEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM H7/1 Green : (-) 200mA Pulse H7 3 Pin H7/3 Blue : (-) 200mA Unlock White LED Indicator Valet Switch H6 2 Pin
More informationCA-110 Installation Instructions
CA-110 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationKE 680 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.
KE 680 DELUE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD Installation And Operation Manual MEGATRONI CALIFORNIA, U.S.A. KE 680 1 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10
More informationModel APS-510C Installation Manual Remote Control Vehicle Security System
Model APS-510C Installation Manual Remote Control Vehicle Security System Table Of Contents: Before You Begin Page 2 Wire Harnesses Quick View Page 3 Mounting Of The Major Components Page 4 8 Pin Power
More informationPROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
100755-2 Installation Instructions PC 4200 PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationRemote Keyless Entry Installation Guide ca 2051
PROFESSIONAL SERIES Remote Keyless Entry Installation Guide ca 2051 ca2051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More informationINSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.
INSTALLATION MANUAL SL- 3 3-Channel Security with Keyless Entry System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty information:
More informationALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATION PRECAUTIONS & WARNINGS
CS-882 OEM ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATI PRECAUTIS & WARNINGS NOTE: This system does not improve or affect the range of the factory remote keyless entry transmitters.
More informationMEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 INSTALL 1
MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation Manual MEGATRONI CALIFORNIA, USA MEGA 2500 INSTALL 1 MEGA 2500 INSTALL 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationCA-210 Installation Instructions
CA-210 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationRemote Start with Keyless Entry Installation Guide ca5054
PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide ca5054 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...3 Wire Connection Guide...4
More information2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE
REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause
More informationOCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.
OCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 670 1 MEGA 670 2 OCT/21/02 OCT/21/02 WIRING DIAGRAM H7: 10 Pin White
More informationAdvanced Remote Vehicle Starting System
INSTALLATION GUIDE 1600 Advanced Remote Vehicle Starting System 1600M AUTOMATIC AND MANUAL TRANSMISSION MODELS WWW.ULTRASTARTERS.COM See website for a full size printable version of this manual. WARNING!!
More informationSecurity and Keyless Entry Installation Guide ca 1051
PROFESSIONAL SERIES Security and Keyless Entry Installation Guide ca 1051 ca1051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection
More informationMM1 Installation Instructions
MM1 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or
More informationDLKEK3HN INSTALLATION INSTRUCTIONS
DLKEK3HN INDEX: INSTALLATION INSTRUCTIONS WIRING INSTRUCTIONS... PG 2-5 LED STATUS INDICATOR... PG 6 VALET/OVERRIDE BUTTON... PG 6 SHOCK SENSOR... PG 7 PROGRAMMABLE JUMPER-PINS... PG 7 PROGRAMMING REMOTE
More informationRS-351-EDP. Installation Guide
RS-351-EDP Keyless Entry & Remote Start Installation Guide June 25, 2013 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin Main Wire Harness...
More informationINSTALLATION GUIDE Table of Contents
CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2
More informationModel PRO 9246CH Installation Manual
Model PRO 9246CH Installation Manual PRE-INSTALLATION NOTES: RF Programmable Features : Feature Selection 1 Flash 2 Flash 3 Flash Default 1st Do L/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L 1 Sec. 2nd Accy Lock
More informationINSTALLATION MANUAL 601-S INFORMATION.) 8. REMOVE DOME LIGHT FUSE TO PRE- VENT BATTERY DRAIN.
FOR NEGATIVE PARKING LIGHTS (MOST JAPANESE VEHICLES) FOR POSITIVE PARKING LIGHTS TRUNK RELEASE CIRCUIT DIAGRAM: OUT TO TRUNK 12V 2nd CHANNEL AUXILIARY (GRAY WIRE) 86 a 85 If the power trunk release requires
More informationMEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1
MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1 OPERATION: A. TRANSMITTER OPERATION: Transmitter Button System Function Remark Lock
More informationFOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES
#STARTC2003-TW TWO-WAY FM/FM REMOTE CONTROL VEHICLE STARTER & ALARM SYSTEM INSTALLATION GUIDE FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES THIS UNIT MUST BE INSTALLED BY AN AUTHORIZED MICRO ALARM
More informationCS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION
CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet
More informationInstallation Instructions
F20/F25 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationMEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1
MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1 MEGA 2500 OPERATE 2 OPERATION: A. TRANSMITTER OPERATION: Transmitter Button System
More informationAutomatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst
PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of
More informationModel PRO 9644a Installation Manual
Model PRO 9644a Installation Manual SELECTABLE FEATURES Note: The method of manual override can either be selected to operate from the valet switch operate as custom code. Be certain to place a check mark
More informationRemote Start with Keyless Entry Installation Guide CA 5051
PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide CA 5051 2010 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More informationCSI-100 Installation Instructions
CSI-100 Installation Instructions Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting
More informationFM SECURITY AND REMOTE START SYSTEM
FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on vehicles equipped with
More informationVehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions
Model PRO 9842 Installation Manual Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 6002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 2-3 Making Connections...
More informationRF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY)
RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY 1 BLUE...TRUNK/HOOD TRIGGER (-) INPUT BLACK/BLUE...4TH
More informationMEGA WAY LCD PAGER ALARM WITH REMOTE ENGINE STARTER. Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. MEGA 2700 OPERATE 1
MEGA 2700 2-WAY LCD PAGER ALARM WITH REMOTE ENGINE STARTER Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. MEGA 2700 OPERATE 1 2 WARNINGS: As with any product that performs automatic functions, there
More informationDLRM DLRM
Table of Contents 1. Before You Begin.........................................................Page 1 2. Installation Tips..........................................................Page 2 3. Mounting Components
More informationAutomatic / Manual Transmission Remote Start with Keyless Entry Installation Guide. ca 5152
PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide ca 5152 1 Table of Contents Before You Begin... 3 Wire Connection Guide... 4 11 Pin Main Harness...
More informationVS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1
VS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1 VS 655 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10 Pin White
More informationPROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
Installation Instructions CPL Master Module PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More information"WE'VE GOT THE EDGE ON SECURITY" INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV
"WE'VE GOT THE EDGE ON SECURITY" INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT INC. 1997 Contents 5 WIRE HARNESS CONNECTIONS Black Wire (Chassis Ground)...
More informationSecurity and Remote Start Installation Guide for models: ca6554
PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6554 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...4 Wire Connection Guide...5
More informationModel AX-510 Owner s Manual
Model AX-510 Owner s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped with
More informationRS-340-EDP+ / RS-450-EDP+
RS-340-EDP+ / RS-450-EDP+ Deluxe Keyless Entry & Remote Start Installation Guide July 11, 2012 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin
More informationModel K20 installation guide. ProSecurity
Model K20 installation guide ProSecurity NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional
More informationInstallation Instructions
Installation Instructions for EVS II Security and Keyless Entry Systems Note: It is recommended that this installation take place prior to rustproofing. The individual delivering the vehicle should review
More informationOwner's Manual. Remote Security and Convenience System INS0866 8/98
Remote Security and Convenience System Owner's Manual IMPORTANT NOTE: The operation of the SURESTART as described in this manual is applicable to most vehicles. However, due to the engine type and configuration
More informationCS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION
CS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc.
More informationModel PRO-9775T Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable
Model PRO-9775T Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable FEATURES:! 2 Four Button Programmable RF Transmitters! Four Channel Code Learning Receiver
More informationCSI-400 Installation Instructions
CSI-400 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 7002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 3 Making Connections...
More informationSecurity and Remote Start Installation Guide for models: ca 6552 ca 6552 SST
PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca 6552 ca 6552 SST ca6552/6552sst. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You
More informationSTARTER DISABLE/ KEYLESS ENTRY SYSTEM
I N S T A L L A T I O N M A N U A L STARTER DISABLE/ KEYLESS ENTRY SYSTEM BEFORE INSTALLING THE STARTER DISABLE/KEYLESS ENTRY SYSTEM DO read through this installation manual. DO NOT install the control
More informationVEHICLE SECURITY SYSTEM INSTALLATION MANUAL
VEHICLE SECURITY SYSTEM WITH REMOTE START & NETWORK INTERFACE INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! Before You Begin This system is intended
More informationModel APS-25N Installation Manual
Model APS-25N Installation Manual Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver s do pin switch in der to begin the passive arming sequence. RF Programmable
More informationSecurity and Remote Start Installation Guide for models: ca6553 ca6553sst
PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6553 ca6553sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 4 Wire
More information6 RELAY SYSTEM 5-BUTTON SERIES VEHICLE SECURITY SYSTEM INSTALLATION MANUAL
6 REAY SYSTEM 5-BUTTON SERIES VEHICE SECURITY SYSTEM INSTAATION MANUA Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the
More informationModel APS-25CH Installation Manual
Model APS-25CH Installation Manual Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver s do pin switch in der to begin the passive arming sequence. RF Programmable
More informationCA-510a Installation Instructions
CA-510a Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationModel PRO-9675FT4 Owner's Manual
Model PRO-9675FT4 Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable FEATURES : w 2 Four Button Programmable RF Transmitters w Four Channel Code Learning Receiver
More informationAS-4000 OPERATING INSTRUCTIONS (PS-5000)
AS-4000 OPERATING INSTRUCTIONS (PS-5000) BASIC OPERATIONS This unit is a state-of-the-art combination of a vehicle alarm and remote starter system. Start by familiarizing yourself with the alarm functions
More informationCOMMANDO REMOTE CONTROL ENGINE STARTER. Limited Warranty Statement MADE IN THE U.S.A. IMPORTANT KEEP YOUR INVOICE WITH THIS WARRANTY STATEMENT!
Limited Warranty Statement GNU COMMANDO LINE WARRANTY STATEMENT GNU warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of sale to the original
More information2005 Directed Electronics, Inc. Vista, CA N412V 01-05
Model 211HV Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may
More informationCA 421 Installation Instructions
CA 421 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationCS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS
CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Series Remote Alarm System by Crimestopper Security Products
More informationModel: APS-610a Owner s Manual 4 Button Remote Security System with Dual Stage Shock Sensor
Model: APS-610a Owner s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped
More informationAUTOMATIC TRANSMISSION ONLY! Technical Support: ext 1 Warning!!
REV.2006.04 INSTALL GUIDE AUTOMATIC TRANSMISSION ONLY! www.ultrastarters.com Technical Support: 877-598-2100 ext 1 support@ultrastarters.com Warning!! The system must be placed into Service Mode before
More informationTable of Contents. Owner s Guide
Table of Contents Owner s Guide Arming the System...2 Disarming the System...3 Emergency Override... 4 System Armed & Activated...4 Remote Controller Icons...5-6 Panic... 6 Sensor By-Pass... 6 Auxiliary
More informationModel CSI-300 Owner s Manual
Model CSI-300 Owner s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped
More informationASTRA 4000RS/1000RS SERIES VEHICLE SECURITY SYSTEM WITH REMOTE START PRODUCT MANUAL
ASTRA 4000RS/1000RS SERIES VEHICLE SECURITY SYSTEM WITH REMOTE START PRODUCT MANUAL Remote Transmitters Standard Remote Transmitter Description LED Button 1 Button 2 Button 5 Button 3 Button 4 The ASTRA/G55
More informationModel AS-9234E. Owners Guides
Model AS-9234E Owners Guides This unit is capable of 3 installation methods. Select the guide for your customer that matches the installation in their particular vehicle. PATENTED: www.voxxintlcorp.com/company/patents
More information" MANUALLY OVERRIDING YOUR SYSTEM
Model PRO 2000aS Owner s Manual 3 Button Remote Security System with Keyless Entry IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped with selectable
More informationModel PRO 9649 Owner s Manual
Model PRO 9649 Owner s Manual 3 Button Remote Security System with Starter Disable, & Keyless Entry IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is
More informationRS-X60-EDP / RS-X60-EDP+
RS-X60-EDP / RS-X60-EDP+ Deluxe Keyless Entry & Remote Start Installation Guide July 7, 2014 Temporary cover. Color cover is in a separate file. 1 Table Of Contents Installation Considerations... 3 6 Pin
More informationRemote Start Installation Guide ca 4552
PROFESSIONAL SERIES Remote Start Installation Guide ca 4552 ca4552. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Before You Begin... 3 Wire Connection Guide... 4 4 Pin Main Harness...
More informationA U T O M A T I C T R A N S M I S S I O N M U L T I - C H A N N E L T W O - W A Y L C D R E M O T E S T A R T E R AS-2510 TW.
A U T O M A T I C T R A N S M I S S I O N M U L T I - C H A N N E L T W O - W A Y L C D R E M O T E S T A R T E R S Y S T E M AS-2510 TW User Guide Transmitter Part Number and Module Serial Number...2
More information