SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL
|
|
- Julian Bridges
- 5 years ago
- Views:
Transcription
1 SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location Plug in program switch inside the vehicle that will be difficult for a Harness kit thief to locate, while allowing for a convenient installation position. Wire tie or Dual Stage Electronic Shock sensor* 120dB 6-tone siren* screw the module securely. Owner s manual * NOT INCLUDED WITH E MODELS 2. Mounting the Siren: Before you begin the installation: Mount the siren in a suitable location inside the engine compartment, away from This product must be installed by qualified hot or moving engine parts such as personnel only. Installation by non-qualified exhaust manifolds, turbochargers, fan belts, individuals will void the warranty. etc. Make sure that there is no outside Always use a multimeter to verify vehicle access to the siren from underneath the wiring. Do not use a test light. vehicle or through the grill. Verify LED and override switch placement, Point the siren down so that water may with the vehicle s owner, before mounting not accumulate inside the siren bell. components. Connect the siren s black wire to a solid Perform a careful inspection of all vehicle ground using a star washer and ring terminal. functions before and after installation. Route the red wire through the firewall and cover with tape or split loom tubing for protection. Always use either an 1
2 existing grommet or a new hole with the proper size grommet to protect the wire from chaffing. 6. Flashing Parking Light Output (white wire): Using a volt/ohm meter, locate the wire (usually on the head light switch) that shows +12V when only the parking lights are switched on. European vehicles may require an additional relay if they have separate wires for the left and right side parking lights.this wire has a maximum output of 15 amps. Do not connect to head light circuits. (See diagram section). 3. Mounting the shock sensor: Using a cable tie, mount the shock sensor inside the vehicle to either the steering column, a large wire harness, or a dash brace. Be sure that the adjustment screw on the sensor is accessible for adjustment. Plug the shock sensor harness into the 4- pin white connector on the main module. 4. Installing the Status Indicator (LED): Locate a place where there is enough depth for the LED to fit all the way in, and where it will be easily visible from outside the vehicle. Carefully drill the appropriate size hole (7/16 ) and run the 2 pin red connector through to the matching red connector on the module. Push the LED into the hole, making sure it fits snugly. 5. Installing the Valet Switch: Mount the valet/override switch in a hidden location that can still be found by the customer for emergency override situations. Run the 2 pin blue connector through to the matching blue 2 pin connector on the module V+ Power Input (red wire): Connect the red fused wire on the main harness to the vehicle s battery. 8. Siren Output (brown wire): Connect the brown wire on the main harness to the red wire from the siren. 9. Ground Input (black wire): Connect the black wire to a solid chassis ground. 10. Optional Armed Output (orange wire): This wire provides a ground output when the alarm is armed, to control an optional Starter Disable Relay. Using a volt/ohm meter locate the starter wire (normally a heavier gauge wire) coming from the ignition switch. Cut the wire that shows +12V during cranking only. The vehicle should not be able to start. Connect a relay as shown in diagram section. 11. Horn output (gray wire): This wire provides a pulsed output to drive a relay to honk the horn when the alarm is triggered. Connect to a relay as shown in diagram section on back page. 12. Negative door input (green wire): Connect the green wire from the module to the wire that shows ground when all of the doors are opened. Verify with a volt/ohm meter. Make sure that all doors
3 when opened separately make the target wire provide a ground output. 13. Hood/Trunk switch input (blue wire): Connect the blue wire to the hood and/or trunk pin switch that shows ground when opened. 14. Positive Door input (violet wire): Connect the violet wire from the module to the wire that shows 12V+ when all of the doors are opened. Verify with volt/ohm meter. Make sure that all doors when opened separately make the target wire provide a 12V+ output. 15. Connect the 12V+ ignition input (yellow wire): Connect the yellow wire on the main harness to a main ignition wire. This can be also found in the main ignition switch wire harness. Your volt/ohm meter will read 12V+ when key is turned on. Make sure that this ignition wire has 12V+ on even during the starting process of the vehicle. It is important that the voltage does not drop when the car is starting. Some vehicles have ignition wires that remain or slowly drop to 0 volts.verify that when the ignition is shut off that the voltage drops to 0 Volts immediately. If the yellow wire has voltage on it after the key is turned off, it will keep the alarm from arming via the remote. 16. Connect the door lock input wires: Blue, Green and Red on 3 pin harness. The blue wire receives a pulsed input from the unlock switch. Set polarity mode by entering program mode (page 5). The green wire receives a pulsed input from the lock switch. Set polarity with dipswitch #1. Door Lock Validation Wire: (Red on the 3 pin harness) Use in mode #2 only. This wire allows system to disarm from the remote only. Test features and functions, adjust shock sensor. Arm and disarm system, check that the siren chirps and parking lights are functioning normally. Make sure that the programmed features (via dip switch) are performing correctly, ie.: passive arming. Test the doors and hood or trunk inputs (make sure that you check that all doors trigger the system not just the drivers door). Adjust the shock sensor (clockwise for more sensitive, counter clockwise for less sensitive), make sure that it is not too sensitive. Arm the system and try starting the vehicle, it should not start (optional). Arm the system and disarm it with the ignition and override switch. If programmed to passively arm make sure that the system properly arms. Using the remote and valet switch, check for the user features: valet mode. 3
4 Tie up wire harness, and replace any under dash panels. Deliver the vehicle to customer. Make sure the customer has physical knowledge of the location of the valet/override switch. Valet Mode: 1. Disarm the system. 2.Turn ignition to the ON position. 3. Press and hold valet/override switch for approximately 3 seconds. 4. LED will turn on solid, Siren will chirp once. 3. To turn feature off: Turn ignition off, on, off, on and wait 3 seconds; siren will chirp twice to indicate the feature is turned on. 4. To reset to factory default settings: Enter program mode, then turn ignition key off, on, off, on, off on and wait 3 seconds.the siren will chirp 3 times to set all the features to factory default. System will automatically exit program mode. NOTE: You must re-enter program mode for each feature you wish to change. To exit Valet mode: Repeat the procedure, LED will turn off and the siren will chirp twice. Remote Programmable Features To enter program mode: 1. Turn ignition to the on position. 2. Wait 2 seconds. 3. Within 10 seconds press program switch 5 times. 4. The siren will buzz indicating the system is now in program mode. To change programmable features: 1. Press program switch the number of times that equal to the feature you wish to change.the siren will chirp each time the switch is pushed. (Example: to turn feature #3 off press the program switch 3 times). 2. Once you are at the desired feature location, turn ignition key OFF; then back to ON, wait 3 seconds (siren will chirp once to indicate the feature is ON). 4
5 Programmable Features: Programming Feature ON (Default) OFF 1 = Door lock / unlock inputs: Negative Positive 2 = Disarm validation input: Negative Positive 3 = Disarm validation mode: Mode 1* Mode 2** 4 = Bad zone report: 25 seconds 0 seconds 5 = Arming/disarming report: Chirps No chirps 6 = Passive or Active Arming: Passive Arm Active Arm 7 = Shock sensor adjustment mode*** * If door is unlock input is activated the system will disarm. ** If the door unlock input is activated, the system will not disarm. If both door unlock and disarm validation inputs are activated the system will disarm. *** Siren will chirp when sensing an impact. Door Trigger: If the system is set for mode 2 operation, system will sound siren for 15 seconds before flashing the parking lights.this will prevent the system from being disarmed by the interior door unlocking switch. 5
6 2 STAGE SHOCK SENSOR 12V FLASHING LIGHT OUTPUT (10 AMPS) SEE PAGE 2 SENSOR CONNECTOR DOOR LOCK CONNECTOR GREEN RED BLUE WHITE DOOR LOCK INPUT (SEE PAGE 5) DOOR LOCK VALIDATION MODE #2 DOOR LOCK INPUT (SEE PAGE 5) RED BLACK SIREN OPTIONAL STARTER INTERRUPT RELAY RECEIVER MODULE HARNESS RED BROWN BLACK ORANGE GRAY GREEN BLUE VIOLET YELLOW FUSE FUSE (-) HORN HONK (RELAY MAY BE REQUIRED) NEGATIVE TRIGGER INPUT I.E. TRUNK/HOOD SWITCH OR OPTIONAL SENSOR GROUND +12VDC (+)12V AT BATTERY TO STARTER TO BATTERY IGNITION SWITCH CUT X A 85 D1A DIODE IGNITION WIRE BLUE VALET CONNECTOR VALET SWITCH RED LED CONNECTOR LED 6
7 TROUBLESHOOTING SYMPTOM Parking lights do not flash. Vehicle starts when armed. Car horn honks when system disarmed and door is opened. Alarm system intermittently works. Car won't start;alarm won't function properly. Unit is triggered any time it is armed. Remote Control does not arm or disarm alarm. Valet does not work. Flashing light output does not work. Remote Control does not disarm alarm. Alarm doesn t Arm/Disarm. Alarm will not Passively Arm. PROBABLE CAUSE Wrong wire connected to the WHITE wire, or requires a negative output. Wrong starter wire was cut. Vehicle factory security system needs to be disarmed. Bad power and ground connections. Vehicle battery dead or drops below 7.5 volts when trying to start the vehicle. Sensor not adjusted correctly, BLUE or GREEN wire shorted to ground. Wrong polarity for door lock input. Program #1: ON=(-) pulse OFF=(+) pulse; not connected to proper door lock/unlock wires. Bad switch or wrong activation sequence. Bad connection on WHITE wire or the output polarity is wrong for the circuit being driven. Program switch #2 or #3 are not set in the correct position. Alarm in Valet Mode, ignition input has voltage on it. Make sure the power and ground wires show 12V+ and ground. Program #6 is OFF; wrong polarity door input wire;yellow ignition input has 12V+ on it; alarm in Valet Mode. SUGGESTED CORRECTION Correct the wire connected to the WHITE wire, using a SPDT relay reverse polarity on white wire (see diagrams). Locate proper starter wire and reconnect. Locate disarm wire (drivers kick panel?) use negative unlock pulse to disarm factory system. Replace and secure power and ground connections. Replace battery or charge. Readjust sensor. Disconnect the BLUE or GREEN wire to see if symptom stops, if so check wires for short. Check polarity on door lock wires with correct Program position. Repair or replace switch or check user instructions for proper activation sequence. Check WHITE wire. Connect a Relay to this wire and apply the opposite polarity to the circuit being driven. See mode explanation Page 5. Exit Valet mode; turn key off; connect YELLOW wire in main harness to proper ignition wire. Correct Program #6; Correct door switch polarity; change ignition input wire; make sure alarm is not in Valet. 7
8 STATUS INDICATOR (LED) FUNCTIONS Off= System off in Active Mode Slow Flash= System Armed Rapid Flash= Passive Pre Arm State Rapid Flash (after disarm)= System was triggered On Solid= In Valet On Solid= (After passive prearm or active arm) 2 second final prearm state On Solid= (when disarmed, and not in Valet) Door open. SIREN CHIRP STATUS 1 chirp= system armed 2 chirps= system disarmed 3 chirps= System disarmed, but alarm was triggered while away. 4 chirps= Alarm armed but there is a trigger that remains open. (This occurs 25 seconds after system was armed) 5 rapid chirps= Alarm armed, shock sensor warn away output was triggered. TRIGGER ZONE INDICATOR MODE 2 OPERATION GREEN LOCK 2 Flashes = Door Trigger 3 Flashes = Shock trigger 4 Flashes = Warn away trigger RED BLUE DRIVER'S DOOR UNLOCK PASSENGER'S DOOR FOR POSITIVE PARKING LIGHTS WHITE VEHICLE PARKING LIGHT WIRE FOR NEGATIVE PARKING LIGHTS (MOST JAPANESE VEHICLES) WHITE 86 a TO VEHICLE PARKING LIGHT CIRCUIT STARTER DISABLE ORANGE WIRE IGNITION FUEL SWITCH PUMP 86 a CUT x x 12V+ (IGNITION) STARTER FUSE BLOCK HORN HONK RELAY DIAGRAM: TO (-) HORN (+) HORN GRAY 86 a 85 12V (+) CONSTANT GRAY 86 a NEGATIVE GROUND POSITIVE HORN HORN 12V(+) CONSTANT DLC, Inc /02 - Rev. 3
6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM
6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM Button 1 Button 2 Button 5 Button 3 Button 4 Standard Features: Two 5-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren
More information6 RELAY SYSTEM 5-BUTTON SERIES VEHICLE SECURITY SYSTEM INSTALLATION MANUAL
6 REAY SYSTEM 5-BUTTON SERIES VEHICE SECURITY SYSTEM INSTAATION MANUA Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the
More informationINSTALLATION MANUAL 601-S INFORMATION.) 8. REMOVE DOME LIGHT FUSE TO PRE- VENT BATTERY DRAIN.
FOR NEGATIVE PARKING LIGHTS (MOST JAPANESE VEHICLES) FOR POSITIVE PARKING LIGHTS TRUNK RELEASE CIRCUIT DIAGRAM: OUT TO TRUNK 12V 2nd CHANNEL AUXILIARY (GRAY WIRE) 86 a 85 If the power trunk release requires
More informationCovers All 430, 440, 441 and CJ Series Advanced Security Systems.
INSTALL GUIDE Covers All 430, 440, 441 and CJ Series Advanced Security Systems www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com FCC/ID Notice This device complies with
More informationVEHICLE SECURITY SYSTEM INSTALLATION MANUAL
VEHICLE SECURITY SYSTEM WITH REMOTE START & NETWORK INTERFACE INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! Before You Begin This system is intended
More informationFM SECURITY AND REMOTE START SYSTEM
FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on vehicles equipped with
More informationSecurity and Keyless Entry Installation Guide ca 1051
PROFESSIONAL SERIES Security and Keyless Entry Installation Guide ca 1051 ca1051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationSECURITY SYSTEM INSTALLATION MANUAL
INSTALLATION MANUAL SECURITY SYSTEM BEFORE INSTALLING THE SYTEM DO read through this installation manual. DO NOT install the alarm brain in an engine compartment. The alarm may arm itself when power is
More informationMM1 Installation Instructions
MM1 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or
More informationSTARTER DISABLE/ KEYLESS ENTRY SYSTEM
I N S T A L L A T I O N M A N U A L STARTER DISABLE/ KEYLESS ENTRY SYSTEM BEFORE INSTALLING THE STARTER DISABLE/KEYLESS ENTRY SYSTEM DO read through this installation manual. DO NOT install the control
More informationALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATION PRECAUTIONS & WARNINGS
CS-882 OEM ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATI PRECAUTIS & WARNINGS NOTE: This system does not improve or affect the range of the factory remote keyless entry transmitters.
More informationINSTALLATION MANUAL. Remote Mobile Security System. Model: PL30
Remote Mobile Security System INSTALLATION MANUAL Model: PL30 Copyright 1998 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be
More informationRemote Keyless Entry Installation Guide ca 2051
PROFESSIONAL SERIES Remote Keyless Entry Installation Guide ca 2051 ca2051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More information2 Way Security and Keyless Entry Installation Guide ca 1553
PROFESSIONAL SERIES 2 Way Security and Keyless Entry Installation Guide ca 1553 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More informationManual - Inside Front Cover (Blank)
FRONT COVER Manual - Inside Front Cover (Blank) Table of Contents Important Information... 2 Recommended Installation Tools... 2 Recommended Procecures... 2 Wiring Diagram... 3 14 Pin Connector...4 Installation
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationCP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM
CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION
More informationDLKEK3HN INSTALLATION INSTRUCTIONS
DLKEK3HN INDEX: INSTALLATION INSTRUCTIONS WIRING INSTRUCTIONS... PG 2-5 LED STATUS INDICATOR... PG 6 VALET/OVERRIDE BUTTON... PG 6 SHOCK SENSOR... PG 7 PROGRAMMABLE JUMPER-PINS... PG 7 PROGRAMMING REMOTE
More informationMEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM. White. H1 5 Pin White. H6 2 Pin White.
MEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM H7/1 Green : (-) 200mA Pulse H7 3 Pin H7/3 Blue : (-) 200mA Unlock White LED Indicator Valet Switch H6 2 Pin
More informationCSI-300 Installation Instructions
CSI-300 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces
More informationINSTALLATION MANUAL. Remote Mobile Security System. Model: PL50
Remote Mobile Security System INSTALLATION MANUAL Model: PL50 Copyright 2000 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be
More informationModel APS-101N Installation Manual
Programmable Features Model APS-101N Installation Manual Select By Operating Transmitter Press Lock Button Press Unlock Button Siren Indications 1 Chirp 2 Chirps Factory Default 1) Arming Method Passive
More informationINSTALLATION MANUAL. Model: PLUS Vehicle Security
R Vehicle Security INSTALLATION MANUAL Model: PLUS-5000 Copyright 1999 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be a Registered
More informationPROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
Installation Instructions CPL Master Module PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationPROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
100755-2 Installation Instructions PC 4200 PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationDiablo 2 /AMX 68/AT-58 Installation Manual 3/31/99
1 Table of Contents Required Installation Tools... 2 Important Information... 2 Wiring Diagram.... 3 14 Pin Con nec tor... 4 Starter Dis able Relay...4 Installation Procedures...5 Control Unit... 5 Antenna...
More informationVehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions
Model PRO 9842 Installation Manual Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical
More informationINSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit
R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;
More informationCS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS
CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Series Remote Alarm System by Crimestopper Security Products
More informationCA-110 Installation Instructions
CA-110 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationCS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION
CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet
More informationModel APS-25N Installation Manual
Model APS-25N Installation Manual Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver s do pin switch in der to begin the passive arming sequence. RF Programmable
More informationModel APS-25CH Installation Manual
Model APS-25CH Installation Manual Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver s do pin switch in der to begin the passive arming sequence. RF Programmable
More informationCS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION
CS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc.
More informationRemote Start with Keyless Entry Installation Guide ca5054
PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide ca5054 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...3 Wire Connection Guide...4
More informationFS-30 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION INSTRUCTIONS
FS- 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an Remote Alarm System by Crimestopper Security Products Inc. This booklet contains the information
More informationCA-210 Installation Instructions
CA-210 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationRA2 Installation Manual Rev. B
Important Information Required Installation Tools Voltmeter Wire Strippers Electric Drill & Bits Phillips Screwdriver Convoluted Tubing * Solder Gun * Wire Crimpers Shrink Tube or Electrical Tape * Optional
More informationInstallation Instructions
F20/F25 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationModel APS-510C Installation Manual Remote Control Vehicle Security System
Model APS-510C Installation Manual Remote Control Vehicle Security System Table Of Contents: Before You Begin Page 2 Wire Harnesses Quick View Page 3 Mounting Of The Major Components Page 4 8 Pin Power
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 6002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 2-3 Making Connections...
More informationCS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION
CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Series Remote Alarm System by Crimestopper Security Products
More informationCS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM
INTRODUCTION: CS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Remote Keyless Entry System by Crimestopper Security Products Inc.
More informationAutomatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst
PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of
More informationVEHICLE SECURITY SYSTEM
A10 SERIES VEHICLE SECURITY SYSTEM PRODUCT MANUAL Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The
More informationFS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS
FS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Remote Keyless Entry and Alarm System by Crimestopper Security Products Inc. This
More informationDLRM DLRM
Table of Contents 1. Before You Begin.........................................................Page 1 2. Installation Tips..........................................................Page 2 3. Mounting Components
More informationINSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.
INSTALLATION MANUAL SL- 3 3-Channel Security with Keyless Entry System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty information:
More informationRemote Start with Keyless Entry Installation Guide CA 5051
PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide CA 5051 2010 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More informationREC-11+ REMOTE RECEIVER UNIT
Resetting The Programmable Features The installer may quickly and easily return all 17 programmable features back to the factory settings. Changing individual features were explained in detail in the previous
More informationCSI-100 Installation Instructions
CSI-100 Installation Instructions Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting
More informationModel PRO 9644a Installation Manual
Model PRO 9644a Installation Manual SELECTABLE FEATURES Note: The method of manual override can either be selected to operate from the valet switch operate as custom code. Be certain to place a check mark
More informationMEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 INSTALL 1
MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation Manual MEGATRONI CALIFORNIA, USA MEGA 2500 INSTALL 1 MEGA 2500 INSTALL 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10
More information2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE
REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause
More informationINSTALLATION GUIDE. FCC ID NOTICE
REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This
More informationVS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1
VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 2 INSTALLATION We recommend insulating all your soldered or crimped connections
More informationINSTALLATION GUIDE Table of Contents
CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2
More informationREMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION
CS-2001FC REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet
More information*IMPORTANT INFORMATION:
CS-2003DC REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This system
More informationOCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.
OCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 670 1 MEGA 670 2 OCT/21/02 OCT/21/02 WIRING DIAGRAM H7: 10 Pin White
More informationAviStart 6500 Installation Manual
Table of Contents Important Information... 1 Recommended Installation Tools... 1 Recommended Procedures... 1 Main Wiring Diagrams.... 2 Pin Connectors... 5 Installation Procedures...7 Control Unit... 7
More informationKE 680 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.
KE 680 DELUE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD Installation And Operation Manual MEGATRONI CALIFORNIA, U.S.A. KE 680 1 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10
More informationCS-2002DC & CS-2002DC Series II
CS-2002DC & CS-2002DC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security
More informationSecurity and Remote Start Installation Guide for models: ca6553 ca6553sst
PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6553 ca6553sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 4 Wire
More informationSecurity and Remote Start Installation Guide for models: ca6554
PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6554 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...4 Wire Connection Guide...5
More informationVS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1
VS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1 VS 655 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10 Pin White
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 7002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 3 Making Connections...
More informationSecurity and Remote Start Installation Guide for models: ca 6552 ca 6552 SST
PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca 6552 ca 6552 SST ca6552/6552sst. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You
More informationAUTOMATIC TRANSMISSION ONLY! Technical Support: ext 1 Warning!!
REV.2006.04 INSTALL GUIDE AUTOMATIC TRANSMISSION ONLY! www.ultrastarters.com Technical Support: 877-598-2100 ext 1 support@ultrastarters.com Warning!! The system must be placed into Service Mode before
More informationFOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES
#STARTC2003-TW TWO-WAY FM/FM REMOTE CONTROL VEHICLE STARTER & ALARM SYSTEM INSTALLATION GUIDE FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES THIS UNIT MUST BE INSTALLED BY AN AUTHORIZED MICRO ALARM
More informationInstallation Instructions
Installation Instructions for EVS II Security and Keyless Entry Systems Note: It is recommended that this installation take place prior to rustproofing. The individual delivering the vehicle should review
More informationCS-2003DC & CS-2003DC Series II
CS-2003DC & CS-2003DC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security
More informationModel APS-20B Owner's Manual
Model APS-20B Owner's Manual 3 Button Vehicle Alarm System With Auxiliary Output FEATURES: 2 Three Button RF Transmitters Three Channel Code Learning Receiver Remote Panic In All Modes Built-In Parking
More informationCS-2004 WDC. Remote Control Alarm System with CoolGlow & SecurWatch INSTALLATION & OPERATING INSTRUCTIONS
CS-2004 WDC Remote Control Alarm System with CoolGlow & SecurWatch INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION: CONGRATULATIONS on your choice of a Remote Alarm System by Crimestopper Security Products
More informationCS-2002DPII With Data Port Technology
CS-2002DPII With Data Port Technology REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Remote Alarm System with DP Technology
More informationButton 1 Button 2. Button 3 Button 4. Programmed Remote Transmitter. Button Function Condition
WWW.STELLAR.COM Button Function Condition 1 a. Arm and lock doors b. Car finder with sound c. Temporary stop alarm from sounding d. Remote lock doors 1 for 2 sec. Panic Anytime a. Alarm is disarmed b.
More informationRS-351-EDP. Installation Guide
RS-351-EDP Keyless Entry & Remote Start Installation Guide June 25, 2013 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin Main Wire Harness...
More informationCovers All 35xx Series Advanced 2-Way Remote Starters. Technical Support: ext 0
INSTALL GUIDE Covers All 35xx Series Advanced 2-Way Remote Starters www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com Warning!! The system must be placed into Service
More informationAutomatic / Manual Transmission Remote Start with Keyless Entry Installation Guide. ca 5152
PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide ca 5152 1 Table of Contents Before You Begin... 3 Wire Connection Guide... 4 11 Pin Main Harness...
More informationPress and release the valet switch 3 times 1 Chirp - LED 1 flash
Y Model PRO-9800 Installation Manual SELECTABLE FEATURES Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be certain to place a check
More informationREMOTE START SECURITY SYSTEM
REMOTE START SECURITY SYSTEM Standard Features The System has the following standard features: 5-button remote transmitter Status indicator (LED) Valet/Service mode switch Remote Start capabilities Extended
More informationMaxx 3 Installation Guide
Maxx 3 Installation Guide 2002 Directed Electronics, Inc. Vista, CA N840003 4-02 Table of Contents Important Information....................................................... 3 System Components........................................................
More informationRF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY)
RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY 1 BLUE...TRUNK/HOOD TRIGGER (-) INPUT BLACK/BLUE...4TH
More informationOwner's Manual. Remote Security and Convenience System INS0866 8/98
Remote Security and Convenience System Owner's Manual IMPORTANT NOTE: The operation of the SURESTART as described in this manual is applicable to most vehicles. However, due to the engine type and configuration
More informationCA 421 Installation Instructions
CA 421 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationCSI-400 Installation Instructions
CSI-400 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces
More informationModel AX-510 Owner s Manual
Model AX-510 Owner s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped with
More informationASTRA 4000RS/1000RS SERIES VEHICLE SECURITY SYSTEM WITH REMOTE START PRODUCT MANUAL
ASTRA 4000RS/1000RS SERIES VEHICLE SECURITY SYSTEM WITH REMOTE START PRODUCT MANUAL Remote Transmitters Standard Remote Transmitter Description LED Button 1 Button 2 Button 5 Button 3 Button 4 The ASTRA/G55
More informationAS-4000 OPERATING INSTRUCTIONS (PS-5000)
AS-4000 OPERATING INSTRUCTIONS (PS-5000) BASIC OPERATIONS This unit is a state-of-the-art combination of a vehicle alarm and remote starter system. Start by familiarizing yourself with the alarm functions
More informationCA-510a Installation Instructions
CA-510a Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationInstallation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED. Installation Precautions:
Installation Instructions CA-6 PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or
More informationCOMMANDO REMOTE CONTROL ENGINE STARTER. Limited Warranty Statement MADE IN THE U.S.A. IMPORTANT KEEP YOUR INVOICE WITH THIS WARRANTY STATEMENT!
Limited Warranty Statement GNU COMMANDO LINE WARRANTY STATEMENT GNU warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of sale to the original
More informationRS-340-EDP+ / RS-450-EDP+
RS-340-EDP+ / RS-450-EDP+ Deluxe Keyless Entry & Remote Start Installation Guide July 11, 2012 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin
More information"WE'VE GOT THE EDGE ON SECURITY" INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV
"WE'VE GOT THE EDGE ON SECURITY" INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT INC. 1997 Contents 5 WIRE HARNESS CONNECTIONS Black Wire (Chassis Ground)...
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE ALARM AND REMOTE STARTER MODEL RS602E CONTENTS System Features... 1 System Components... 1 Tools Required... 1 Technical Assistance... 2 Before You Begin... 2 Precautions...
More informatione-ask electronic Access Security Keyless-entry
e-ask electronic Access Security Keyless-entry Multiplex System Multiplex System Installation & Instructions (UM15 ~ 22272-03) Table of Contents Introduction... 1 Standard e-fob Operation and Features...
More informationResponder 350. Installation Guide
Responder 350 Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may
More information12V PROGRAMMABLE POWER OUT
Page 1 ACCESSORIES STARTER IGNITION BATTERY WIRES SIDE VIEW BLUE RED YELLOW 30 A 10 A BLUE / WHITE YELLOW WHITE / BLUE WHITE / DOOR TRIGGER See opt. 16 DOOR TRIGGER (input positive) See opt. 16 PARKING
More information