Instructions. Quick Term II 2047MT 56. 3M Quick Term II. Silicone Rubber Termination (with High-K Stress Relief)

Size: px

Start display at page:

Download "Instructions. Quick Term II 2047MT 56. 3M Quick Term II. Silicone Rubber Termination (with High-K Stress Relief)"

Chad Higgins
5 years ago
Views:

1 Instructions Quick Term II Silicone Rubber Termination (with High-K Stress Relief) IEEE Std. No Class Termination 5 kv Class 50 kv BIL Kit Contents Hi K Silicone Rubber Termination Scotch 70 Silicone Rubber Tape Strip(s) Neutral Wire Ground Clip Pack of Silicone Grease Instruction Sheet ÁÁ 5 to 4.5 kv Kit Selection Chart NOTE: Final determining factor is cable insulation diameter. Kit No Cable Insulation O. D. Range in. (6 8 mm) in. ( 5 mm) in. (7 46 mm)..0 in. ( 5 mm) 5 kv #4 4/0 ( 00) (0 50) (50 65) ( ) Table Conductor Range (AWG & kcmil) 5/8 kv #4 /0 ( 60) /0 50 (50 85) (85 400) ( ) 4.5 kv # 4/0 (50 00) 4/0 500 (00 50) (50 65) M Quick Term II Silicone Rubber Termination Kits for use on Concentric Neutral (CN) Cable Concentric Neutral Cable SCALE: ISSUE DATE: 7//9 ISSUE: Not to scale 047MT 56

2 Correct Installation of Termination Binding Wire or Vinyl Tape Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä ÁÁÁÁ ÁÁÁÁ Ridge at End of Cable Insulation Shield (Semi-Con) Ridge at End of High-K Tube Semi-Con Insulation Shield Cable Insulation Conductor High-K Stress Relief A. Prepare Cable. Check to be sure cable size fits within kit range as shown in Table (cover page).. Train cable into position and cut to length required for installation. Allow sufficient neutral wire length for neutral connection.. Bind neutral wires with a piece of wire or vinyl tape at dimension [A] + [B] Table. (See * below) 4. Bend the neutral wires over the binding wire or vinyl tape. 5. Remove cable semi-conductive insulation shield (semi-con) for a distance of [C] plus [B] Table. (See * below) 6. Remove cable insulation 4 from end of conductor for distance [B] Table Place a marker tape back from semi-con cut edge as shown. 6 Kit No [A] * / 4 (98 mm) / 4 (98 mm) / 4 ( mm) / 4 ( mm) Dimension [B] Depth of Terminal Lug Barrel Table [C] * 8 / 4 (6 mm) 8 / 4 (6 mm) 9 (9 mm) 9 (9 mm) * add to [A] and [C] for short lug barrels ( or less). [A] [C] [B] Neutral Wire Binding Wire or Vinyl Tape 6 Marker Tape 4 Cable Insulation Semi-Con Insulation Shield Conductor 5 DO NOT LOOP NEUTRAL WIRES BEYOND MARKER TAPE

3 B. Install Lug or Connector. These units were designed to fit over Scotchlok and M copper and aluminum lugs. If other lugs will not fit through the core of the termination, slide termination on cable before installing lug. Do not remove core at this time.. When using M type lugs or connectors, refer to the tooling index (Pages 5 and 6) for crimping information.. Position lug or connector and crimp according to manufacturers directions. Remove excess contact aid and sharp crimp flash. C. Clean Cable Insulation and Lug Barrel Using Standard Practice. Wipe the cable insulation with an approved solvent. Do not allow solvent to touch semi-con insulation shield!. If abrasive must be used: a. Use on insulation only. Do not use abrasive on semi-con insulation shield! b. Use only aluminum oxide abrasive; grit 0 or finer or Scotch A Electrician s Abrasive Roll. c. Be careful not to reduce the cable insulation diameter below that allowed by the kit. D. Install Termination. Important: A track resistant seal must be made between the silicone termination insulator and connector using one of two gray Scotch 70 Silicone Rubber Electrical Tape Strips (contained in kit). If the lug barrel is smaller than the cable insulation, wrap the bottom end of the lug with gray silicone tape to the approximate diameter of the cable insulation.. Cover the edge of the semi-con insulation shield with a liberal coating of silicone grease. On this product the silicone grease does not serve as a lubricant. It must be used to fill the step at the semi-con cutoff. IMPORTANT Do Not Forget Silicone Grease ÁÁÁÁ Silicone Grease Gray Silicone Tape

4 Install Termination (continued). Slide the termination body onto the cable and remove core by unwinding, counter-clockwise, starting with the loose end. Make sure the termination body is butted up to the edge of the marker tape. 4 Tip: An occasional tug of the strand while unwinding will aid in core removal. Ä Ä Ä Ä Ä Ä 4 Marker Tape ÁÁÁ Gray Silicone Tape 4. Complete the lug seal using the second gray silicone tape strip. Overlap insulator by one inch and extend tape wrapping onto lug barrel as shown. 5 ÁÁ ÁÁ ÁÁ 5 Gray Silicone Tape E. Grounding. Snap stainless steel grounding clip onto base of termination. Clip must be applied to the base of the termination, between the bottom two rings. Loop one neutral strand around ground clip ends, pulling clip tight onto the termination.. Bundle all neutral wires together and connect to ground. Ä Stainless Steel Grounding Clip 4

5 Tooling Index Crimping Information for M Stem Connectors Copper/Aluminum Conductor CRIMPING TABLE FOR M STEM TYPE CONNECTOR Recommended Crimping Tools M Connector No. Manufacturer Mech. Tool Die (No. Crimps) Hydraulic Tool Die (No. Crimps) Burndy MD6 BG(4), W4(4) Y5, Y9, Y45** U5ART, U4 # Sol. #, # /0 SC000 SC000 SC000 Kearny T & B 0 5, 0 5 TBM 8 5/8 (4) Olive, 0, 40, Ton TBM 5 5/8 (4) 50* Anderson VC 6 Universal Burndy MD6 W669(0) 840(5)* Y5, Y9, Y45** U8ART /0 /0 4/0 SC000 SC000 SC0040 Kearny T & B 0 5, 0 5 TBM 8 840(5)* WH, WH TBM Anderson VC 6 Universal Lug and Crimping Information for Scotchlok Copper/Aluminum Lugs 4006 thru One hole 40 thru 4078 Two hole Cable AWG/ kcmil Stud (in.) Scotchlok Lug Number Burndy Corporation MD6 MY9 Y4A Y5, 9, 45*, 46* CRIMPING TOOL-DIE SETS (NO. OF CRIMPS) Thomas & Betts Corporation ** Y000 TBM 5 TBM 8 TBM TBM 5 Square D Co. Anderson Div. VC6 ** VC6 FT** VC8C** ITT Blackburn Co. OD58 Kearne Nat l Div. TYPE / W6 6 AWG A6CAB U6CABT Grey Grey 9 BY9 J 4 5 / W6 4 AWG A4CAB U4CABT Green Green 7 BY5 P 4004 W W6 AWG AWG ACAB ACAB UCABT UCABT Pink Pink Pink Pink 4H 4H BY BY W6 W6 AWG AWG ACAR ACAR UCART UCART Gold Gold Gold Gold BY BY / W4 W4 W4 /0 /0 /0 A5AR A5AR A5AR U5ART U5ART U5ART Tan Tan Tan Tan Tan Tan BY5 BY5 BY5 / BG(4) /0 407 BG(4) /0 A6AR A6AR U6ART U6ART Olive Olive Olive Olive 54H 54H BYC BYC 5 /8 5 /8 / W66(4) /0 A7AR 404 W66(4) /0 A7AR U7ART U7ART Ruby Ruby Ruby Ruby / W660(4) W660(4) W660(4) 4/0 4/0 4/0 A8AR A8AR A8AR U8ART U8ART U8ART 66(4) 66(4) 66(4) BY5C(4) BY5C(4) BY5C(4) 840(4) 840(4) 840(4) W49 W49 W49 A9AR A9AR A9AR U9ART U9ART U9ART 7H(4) 7H(4) 7H(4) 7H 7H 7H A0AR A0AR U0ART U0ART 76H(4) 76H(4) UART UART UART 87H 87H 87H UART(4) 94H(4) 94H(4) U4ART(4) U4ART(4) 06H(4) 06H(4) 06H 06H U6ART(4) 5H U9ART(4) U9ART(4) 5H(5) 5H(5) S44ART(4) S44ART(4) 40H(4) 40H(4) * Y45 and Y46 accept all Y5 dies ( U series). For Y45 use PT655 adapter. For Y46 use PUADP adapter. ** Anderson VC6, VC6 FT, VC8C and Burndy Y000 require no die set. 5

6 Tooling Index Lug and Crimping Information for Scotchlok Copper Lugs 004 thru 0045 One hole 06 thru 068 One hole long barrel 45 thru 78 Two hole Cable AWG/ kcmil Stud (in.) Scotchlok Copper Lug Number Burndy Corporation MD6 MY9 Y4A CRIMPING TOOL-DIE SETS (NO. OF CRIMPS) Thomas & Betts Corporation Y5, Y9 Y45*, Y46* TBM 5 TBM 8 TBM 5 Square D Co. Anderson Div. VC6, VC6 FT** 6 0 / 4 5 / AWG U5CRT Blue Blue Universal 4 0 / W6 4 AWG A4CR U4CRT Grey Grey Universal / 4 5 / W6 AWG ACR UCRT Brown Brown Universal 5 / AWG ACR UCRT Green Green 7 Universal /0 5 / W6 /0 A5R U5RT Pink Pink 4H Universal / W4 W4 /0 /0 A6R A6R U6RT U6RT Black Black Black Black Universal Universal /0 004 W4 /0 A7R U7RT Orange Orange 04 W4 /0 A7R U7RT Orange Orange Universal Universal 4/ BG BG(4) BG(4) 4/0 4/0 4/0 A8R U8RT U8RT U8RT Purple Purple Purple Purple Purple Purple 54H 54H 54H Universal Universal Universal W66(4) 50 A9R U9RT Yellow Yellow 6 Universal A0R U0RT White 66 Universal AR URT Red(4) 7H(4) AR URT Blue(4) 76H(4) A4R U4RT Brown(4) U6RT Green(4) 94H(4) / Y9, Y45, Y46: U9RT(5) 06H(4) Y45: S44RT(6) Y46: P44RT(6) 5H(4) IMPORTANT NOTICE TO PURCHASER: All statements, technical information and recommendations related to the Seller s products are based on information believed to be reliable, but the accuracy or completeness thereof is is not guaranteed. Before utilizing the product, the user should determine the suitability of the product for its intended use. The user assumes all risks and liability whatsoever in connection with such use M Electrical Products Division 680 River Place Blvd. Austin, Texas All statements or recommendations of the seller which are not contained in the Seller s current publications shall have no force or effect unless contained in an agreement signed by an authorized officer of the Seller. The statements contained herein are made in lieu of all warranties express or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose which warranties are hereby expressly disclaimed. M 99 SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING BUT NOT LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER S PRODUCTS.

Quick Term II. Cold Shrink Silicone Rubber Termination. Quick Term II. Instruction Sheet

Quick Term II. Cold Shrink Silicone Rubber Termination. Quick Term II. Instruction Sheet Quick Term II Cold Shrink Silicone Rubber Termination Instruction Sheet IEEE Std. No. 48 1990 Class 1 Termination 15 kv Class 110 kv BIL Kit Contents: 1 Hi K Silicone Rubber Termination 2 Scotch 70 Silicone