TL INSTALLATION MANUAL FOR TELMA AF50-55 ON CHEVROLET G4500 CUTAWAY 6.0L GASOLINE and 6.6L DIESEL ENGINE
|
|
- David Pope
- 5 years ago
- Views:
Transcription
1 INSTALLATION MANUAL FOR TELMA AF50-55 ON CHEVROLET G4500 CUTAWAY 6.0L GASOLINE and 6.6L DIESEL ENGINE 1apr17jh
2 TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 1.3 Fuel Tank 2 Telma Installation 2.1 Installation Kit TIK10317 for Gasoline 6.0L (TIK10316 for Diesel 6.6L) 2.2 Install the Chassis Brackets 2.3 Assemble the Telma Brackets and mounts 2.4 Install the Telma in the Chassis 2.5 Drive Shaft Modification and Installation 2.6 Axle Shim Installation 2.7 Exhaust Modification 3 Control Components 3.1 Relay Box Installation 3.2 Light Bar Installation 3.3 Telma Control Module (TRCM) Installation 4 Wiring Harness Installation 4.1 Harness Assembly Layout 4.2 Power Harness Installation 4.3 Control Harness Installation 4.4 Wiring Diagram 5 Recommended Tools 6 Post Install Checklist 7 Appendix G WB Installation Drawing with 6.6L Diesel Engine G WB Installation Drawing with 6.0L Gasoline Engine G WB Installation Drawing with 6.6L Diesel Engine G WB Installation Drawing with 6.0L Gasoline Engine G to177 WB Installation Drawing with 6.6L Diesel Engine G to177 WB Installation Drawing with 6.0L Gasoline Engine G to182 WB Installation Drawing with 6.6L Diesel Engine G to182 WB Installation Drawing with 6.0L Gasoline Engine G to187 WB Installation Drawing with 6.6L Diesel Engine G to187 WB Installation Drawing with 6.0L Gasoline Engine G to191 WB Installation Drawing with 6.6L Diesel Engine G to191 WB Installation Drawing with 6.0L Gasoline Engine G to191 WB Installation Drawing with 6.0L Gasoline Engine 1-2 Page 2 of 29 1apr17jh
3 SECTION 1 PREPARATION OF THE CHASSIS 1.1 DRIVELINE Remove the complete drive-shaft assembly after measurements have been taken. 1.2 EXHAUST An exhaust modification is needed for all wheelbases to route the exhaust between the Telma side plate bracket and the frame. Keep all components at least ¼ away from the side plate bracket to prevent vibrations through the exhaust. 1.3 FUEL TANK An aft-of-axle fuel tank and no mid ship tank is required for Telma installation Page 3 of 29 1apr17jh
4 SECTION 2 RETARDER INSTALLATION 2.1 INSTALLATION KIT TIK10317 (TIK10316 diesel 6.6L) P/N DESCRIPTION QTY LFA AF50-55 / 12v with 156 index 1 JZ1007XX-45 Telma Shock Mount Set - 45 Shore 1 TIB01017 CONTROL/RELAY BOX BRACKET 2 TIB Chevy GMT TRCM Bracket 1 TIB07000 Chevy / Ford LVR5 Chassis Bracket 2 TIB07005 (TIB07003 diesel) AF Driver (left) Side Retarder Bracket 1 TIB07006 (TIB07004 diesel) AF Passenger (right) Side Retarder Bracket 1 TID17002 OBD2 HARNESS for AF55 1 TIF01064 hex head bolt 1/4-28 x 1.25 for TRCM mounting 2 TIF05005 hex head bolt 1/4-28 x 0.75 for TRCM bracket mounting 2 TIF01066 Nylon Insert Locknut ZP 1/4-28 UNF 4 TIF05005 BOLT 1/4-28UNF x 3/4 HEX HEAD G8 2 TIF05010 LOCKWASHER 5/16 SPLIT 4 TIF05011 NUT 5/16 4 TIF05012 BOLT 5/16-18UNC x 1-1/2 HEX HEAD G5 4 TIF05013 BOLT 1/2-13UNC x 1-1/2 HEX HEAD G5 2 TIF05014 LOCKWASHER 1/2 MED SPLIT 2 TIF pt Head Bolt M12 x 1.75 x 25 8 TIF07001 M12 x 1.75 x 35 Grade 10.9 Black Phosphate 6 TIF /16-14 x 1.75 Hex Flange Bolt Full Thread Grade 8 12 TIF /16-14 Hex Flanged Locknut Grade 8 12 TIG11010 TELMA LIGHT BAR DISPLAY 1 TIG31064 Telma Control Module GM CAN 1 VF Trep washer M12 for retarder bracket 6 Page 4 of 29 1apr17jh
5 2.2 INSTALLATION OF THE CHASSIS BRACKETS Remove any bolts such as battery box and/or exhaust hanger mounts that will interfere with the chassis bracket mounting Mark the reference hole on the left and right of the chassis rail at dimension T1 down from the outside top of the frame and dimension CC back from the center of the transmission u-joint. Drill a single 7/16 hole in the frame at the dimension of CC and T1 and bolt the chassis bracket (TIB07000) against the outside of the frame using the reference hole in the bracket. Attach the chassis brackets to the frame rail using the flanged head bolts 7/16-14UNC x 1.75" (TIF07002) and flanged lock nuts (TIF07003) included in the kit. Rotate the bracket to the angle specified on the installation drawing and tighten the bolts to 70 lb-ft (±10%). NOTE: Use electronic anglemeter with 0.1 accuracy (e.g. SPI Pro360 digital protractor). All angles indicated are with frame reference of 0. Drill five additional 7/16 holes in each frame rail evenly spaced across the chassis bracket and the rest of the flanged head bolts 7/16-14UNC x 1.75" (TIF07002) and flanged lock nuts (TIF07003) included in the kit. Tighten the 7/16 bolts to 70 lb-ft (±10%). Drill through the chassis bracket any holes needed for battery box and/or exhaust hanger mounts and reinstall the original bolts that were previously removed. It may be necessary to make a 5/16 spacer to keep the accessory brackets flush on the outside of the frame rail. Brackets are slotted so that they can be installed in the stretch area. Page 5 of 29 1apr17jh
6 2.3 ASSEMBLE THE TELMA BRACKETS AND MOUNTS Identify the driver s side of the Telma from the passenger side. The power connection block is on the passenger side top corner and the ground is on the driver side top corner. Identify the Telma brackets. The longer left (driver) side bracket is TIB07005 for gasoline or TIB07003 for diesel. The shorter right (passenger) side bracket is TIB07006 for gasoline or TIB07004 for diesel. Use three hex head bolts M12x1.75x35mm (TIF07001) and Trep washers (VF201400) provided in the kit to attach each Telma bracket onto the unit. Tighten bolts to 35 lb.-ft (±5 lb-ft) Mark all fasteners with paint after tightening to proper torque. Install the rubber mounts into the retarder brackets as shown below. Insert the male parts of the rubber mounts into the 1 5/8 holes in the brackets from the bottom and the other half of the rubber mount on top. Place one 2 ¾ diameter 5/8 flat washer on the top and bottom of each mount and another on the bottom between the chassis bracket and nut. 2.4 INSTALL THE TELMA IN THE CHASSIS Lower the Telma, equipped with its brackets and mounts, into place on top of the chassis brackets. Install the M16x1.5x100mm (4 ) bolts and spring washers down through the holes in the mounts and brackets at each mount. Install 2 ¾ diameter flat washers, spring washers and M16 locknuts at each mount as shown below and tighten to 150 lb.-ft (±10%). Page 6 of 29 1apr17jh
7 2.5 DRIVE SHAFT MODIFICATION AND INSTALLATION A slip assembly is required on each side of the Telma. The slip position should be at center of slip travel when the shaft is installed. Refer to GM Upfitters guidelines for proper drive shaft manufacture, balance, straightness, and critical speed limits. Refer to the installation drawings in the appendix for shaft length guidelines. Always verify proper shaft lengths before modification after Telma is installed. Connect the Telma flange yoke of each drive shaft to the Telma coupling flange using the M12x1.75x25mm 12 point head bolts with patch-lock (TIF07000) supplied in the kit. Tighten to 85 lb-ft (±5 lb-ft). Mark with paint after tightening to proper torque. Page 7 of 29 1apr17jh
8 2.6 AXLE SHIM INSTALLATION Some installation configurations require the addition of steel shims to adjust the axle angle. Refer to GM guidelines for proper shim type and procedure Below are some guidelines - Loosen the spring u-bolt nuts - Lift the chassis by the frame rail until the shim can be slid over the centering pin. - To reduce the axle angle (as shown in the example), the thicker part of the shim should be toward the front of the vehicle. The nose of the axle will go down. - Lower the chassis and tighten the u-bolts. In some cases a new spring pack bolt will need to be installed to make sure the centering pin extends far enough into the spring pad hole. 2.7 EXHAUST MODIFICATION Modify the exhaust as shown below to clear brackets. Page 8 of 29 1apr17jh
9 SECTION 3 CONTROL SYSTEM COMPONENTS INSTALLATION 3.1 RELAY BOX MOUNTING Install the relay box on the inside of the driver side frame rail as high as possible using the relay box mounting brackets TIB01017 x 2 and fasteners supplied in the kit. Tighten the four 5/16 bolts to 17 lb-ft (±10%) and the two ½ bolts to 75 lb-ft (±10%). 3.2 LIGHT BAR INSTALLATION The Light Bar should be mounted so that it is easily visible to the driver. Make a rectangular hole, 7/8 wide x 1 ¾ tall in the lower dash to the right of the steering column or install the Light Bar in an existing console receptacle. Feed the harness through the hole and connect to the Light Bar. Plug the light bar into the hole. PANEL LIGHT BAR DISPLAY Page 9 of 29 1apr17jh
10 3.3 TELMA CONTROL MODULE INSTALLATION Bracket TIB05048 is used to mount the Telma Control Module as shown below. Page 10 of 29 1apr17jh
11 SECTION 4 WIRING HARNESS INSTALLATION 4.1 HARNESS ASSEMBLY LAYOUT Control Module Telma PN: Date Code: Page 11 of 29 1apr17jh
12 4.2 POWER HARNESS INSTALLATION From the relay box, route the Telma power connection and ground harness along the inside of the left frame rail and up over the top along the middle of the Telma. Connect the 10G orange, blue, yellow, and brown wires to the connecting block at the top right corner. Connect the 10G relay box ground cable and the 4G Telma main ground cable to the insulated ground terminal at the Telma top left corner. Coat the terminals with anti-corrosion paint or body undercoat after the connections are made. Secure the harness to the center of the Telma brackets with rubber coated cable clamps. The harness should be secured along the centerline of the Telma and as far away as possible from either rotor to avoid heat damage to the harness. No cables should cross the heat outlets in the periphery of the rotors. Continue across with the black 4G ground cable and connect to negative terminal of the battery pack on the passenger side. Route the red power positive cable along the cross member in front of the Telma and connect to the positive terminal of the battery pack on the passenger side. Secure the cable to the cross member with rubber coated cable clamps. GROUND CONNECTION AT TOP LEFT CORNER SECURE HARNESS TO RETARDER USING RUBBER POWER CONNECTIONS AT TOP RIGHT CORNER Page 12 of 29 1apr17jh
13 4.3 CONTROL HARNESS INSTALLATION AND TRCM CONFIGURATION Route the control harness into the cab through the rubber grommet in the floor under the driver s seat. Follow the OEM harness under the carpet to the dashboard. Connect the main harness to the sub-harness at the connector labeled TO RELAY BOX. Find the Telma Control Module cab harness and plug the two plugs into the Telma Control Module. Plug the foot switch connector onto the rotary foot switch. Remove the OEM OBD2 diagnostics connector from its attachment points under the dash and plug the mating OBD2 connector of the Telma harness into the OEM OBD2 connector. Secure together with a wire tie. Attach the OBD2 connector of the Telma harness to the OEM attaching points where the OEM OBD2 diagnostics connector was installed. Attach the mating connector to the four wires (org, blu, yel, brn) found in the relay box control harness and plug into the cab harness receptacle labeled to relay box. After installation is complete, connect the PC to check TRCM configuration and test the system as an end-line-line quality check. Set speed to 0 mph temporarily to test the system when stopped to ensure proper function. Do not forget to change speed cutoff back to 2.0 mph after testing. After changes are made press the send all config button to update the current vales. It may be necessary to unplug the gray connector from the module and reconnect in order to power cycle after a configuration change has been made for the current values to update. The configuration settings are in the table below. Make sure to check telmausa.com to download and install the latest Telma Desktop Client to use ( and later) and the check that firmware revision is or above. Configuration Settings Ford F550 shuttle Low/High Low CAN G Speed 2.0mph Set point Stage 1 3% Set point Stage 2 5% Set point Stage 3 7% Set point Stage 4 10% Page 13 of 29 1apr17jh
14 4.4 WIRING DIAGRAM SECTION 5 RECOMMENDED TOOLS Transmission Jack Heavy duty drill motor Standard assortment of mechanics hand tools Vehicle hoist, pit, or floor jack with stands Electrical connector crimping pliers for use with non-insulated connectors Electronic angle meter with 0.1 accuracy (e.g. SPI Pro360 digital protractor) Laptop or desktop Windows computer with DB9 serial port or USB-to-serial port adapter TIG DB9 serial extension cable (male/female) Page 14 of 29 1apr17jh
15 SECTION 6 POST INSTALL CHECKLIST TL Revised 19may15 INSTALLATION FOLLOWUP CHECKLIST Retain a copy of this checklist in the chassis VIN record Record Telma serial number in electronic VIN record harness properly routed along center of Telma away from rotors and secured with cable clamps to retarder bracket minimum 1/4" clearance between chassis bracket and retarder bracket CHASSIS #: CHASSIS MAKE/MODEL: Telma part number: Telma Serial number: End Customer: INSTALLER: INSPECTION DATE: INSPECTED BY: X COMMENTS harnesses routed on inside of frame rail away from heat sources, sharp edges, etc. and secured with rubber coated metal cable clamps ELECTRICAL MECHANICAL correct cable eyelet size at battery / disconnect switch relay box mounted vertical with wiring exiting from the bottom and can be easily accessed Telma battery power cable connected to battery switch or to battery "+" terminal and is protected with corrosion inhibitor Telma battery ground cable connected to frame rail bare metal surface where battery pack is grounded or directly to battery ground post and protected with corrosion inhibitor relay box ground connected to retarder ground post electrical connections (weatherproof connectors, no quick splice, avoid butt connectors) Light Bar Display installed correctly, visible to driver, and operates properly Telma Control Module accessible and secured with screws Telma foot control shuts off automatically at 1mph Telma activates when moving and brakes are applied Connect PC to TRCM to check proper configuration and function Telma hydraulic brake foot switch brackets installed correctly cables, hoses and air lines are at least 4" from rotors or heat shield installed drive shaft weld quality, slip installed on each side of Telma at center of travel, balance, u-joints same quality as OEM Transmission angle measurement Telma angle measurement First shaft angle and installed length measurement Second shaft angle and installed length measurement Third shaft angle and installed length measurement Fourth shaft angle and installed length measurement Axle angle measurement drive shaft lengths/angles, Telma angle conforms to drawing Flange yokes are in same plane Page 15 of 29 1apr17jh
16 APPENDIX Page 16 of 29 1apr17jh
17 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 159.0" VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.6L DIESEL SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 9.9 TRANSMISSION= 3.0 CHASSIS BRACKET= 0.0 L2 UNLOADED WITH BODY (±1.0 ) = 7.0 L1= 4.5 RETARDER= 4.5 L2 LOADED (±1.0 ) = 4.2 AXLE= 4.5 A B1 C1 T1 CC L1 L /8 57 3/8 SHAFT LENGTH /2 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 23 1/4 21 3/4 23 1/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07003, TIB07004 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.5 with frame reference of 0 Page 17 of 29 1apr17jh
18 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 159.0" VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.0L GASOLINE SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 10.1 TRANSMISSION= 4.5 CHASSIS BRACKET= -0.5 L2 UNLOADED WITH BODY (±1.0 ) = 7.2 L1= 5.0 RETARDER= 4.0 L2 LOADED (±1.0 ) = 4.4 AXLE= 4.0 A B1 C1 T1 CC L1 L2 2 9/ /8 57 3/8 SHAFT LENGTH 51 1/ /16 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 21 3/4 21 3/4 21 3/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07005, TIB07006 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.0 with frame reference of 0 Page 18 of 29 1apr17jh
19 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 177.0" VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.6L DIESEL SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 8.0 TRANSMISSION= 3.0 CHASSIS BRACKET= 0.0 L2 UNLOADED WITH BODY (±1.0 ) = 5.9 L1= 3.3 RETARDER= 4.5 L2 LOADED (±1.0 ) = 3.9 AXLE= 4.5 A B1 C1 T1 CC L1 L /8 7 3/ /8 SHAFT LENGTH 58 15/ /8 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 23 1/4 21 3/4 23 1/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07003, TIB07004 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.5 with frame reference of 0 Page 19 of 29 1apr17jh
20 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 177.0" VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.0L GASOLINE SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 8.4 TRANSMISSION= 4.5 CHASSIS BRACKET= -0.5 L2 UNLOADED WITH BODY (±1.0 ) = 6.3 L1= 3.5 RETARDER= 4.0 L2 LOADED (±1.0 ) = 4.3 AXLE= 4.0 A B1 C1 T1 CC L1 L2 2 9/16 6 1/8 7 1/16 3 3/4 65 3/8 SHAFT LENGTH 58 15/ /8 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 21 3/4 21 3/4 21 3/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07005, TIB07006 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.0 with frame reference of 0 Page 20 of 29 1apr17jh
21 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 177.0" stretch from 159 VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.6L DIESEL SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 7.0 TRANSMISSION= 3.0 CHASSIS BRACKET= 0.0 L2 UNLOADED WITH BODY (±1.0 ) = 5.2 L1= 3.8 RETARDER= 4.5 L2 LOADED (±1.0 ) = 3.4 AXLE= 4.5 A B1 C1 T1 CC L1 L /16 7 3/ /8 SHAFT LENGTH 50 15/ /16 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 23 1/4 21 3/4 23 1/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07003, TIB07004 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.5 with frame reference of 0 Page 21 of 29 1apr17jh
22 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 177.0" stretch from 159 VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.0L GASOLINE SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 7.9 TRANSMISSION= 4.5 CHASSIS BRACKET= -0.5 L2 UNLOADED WITH BODY (±1.0 ) = 6.1 L1= 3.5 RETARDER= 4.0 L2 LOADED (±1.0 ) = 4.3 AXLE= 4.0 A B1 C1 T1 CC L1 L2 2 9/ /16 6 5/8 3 1/4 57 3/8 SHAFT LENGTH 50 15/ /9 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 21 3/4 21 3/4 21 3/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07005, TIB07006 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.0 with frame reference of 0 Page 22 of 29 1apr17jh
23 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 182.0" stretch from 159 VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.6L DIESEL SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 6.6 TRANSMISSION= 3.0 CHASSIS BRACKET= 0.0 L2 UNLOADED WITH BODY (±1.0 ) = 4.9 L1= 3.5 RETARDER= 4.5 L2 LOADED (±1.0 ) = 3.3 AXLE= 4.5 A B1 C1 T1 CC L1 L /8 7 1/8 3 3/4 57 3/8 SHAFT LENGTH 50 15/ /16 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 23 1/4 21 3/4 23 1/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07003, TIB07004 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.5 with frame reference of 0 Page 23 of 29 1apr17jh
24 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 182.0" stretch from 159 VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.0L GASOLINE SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 7.2 TRANSMISSION= 4.5 CHASSIS BRACKET= -0.5 L2 UNLOADED WITH BODY (±1.0 ) = 5.5 L1= 3.5 RETARDER= 4.0 L2 LOADED (±1.0 ) = 3.9 AXLE= 4.0 A B1 C1 T1 CC L1 L2 2 9/16 5 5/8 6 5/8 3 1/4 57 3/8 SHAFT LENGTH 50 15/ /16 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 21 3/4 21 3/4 21 3/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07005, TIB07006 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.0 with frame reference of 0 Page 24 of 29 1apr17jh
25 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 187.0" stretch from 159 VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.6L DIESEL SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 5.8 TRANSMISSION= 3.0 CHASSIS BRACKET= 0.0 L2 UNLOADED WITH BODY (±1.0 ) = 4.3 L1= 3.8 RETARDER= 4.5 L2 LOADED (±1.0 ) = 2.8 AXLE= 4.5 A B1 C1 T1 CC L1 L /8 7 3/ /8 SHAFT LENGTH 50 15/ /16 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 23 1/4 21 3/4 23 1/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000, TIB07003, TIB07004 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.5 with frame reference of 0 Page 25 of 29 1apr17jh
26 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 187.0" stretch from 159 VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.0L GASOLINE SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 6.5 TRANSMISSION= 4.5 CHASSIS BRACKET= -0.5 L2 UNLOADED WITH BODY (±1.0 ) = 5.1 L1= 3.5 RETARDER= 4.0 L2 LOADED (±1.0 ) = 3.6 AXLE= 4.0 A B1 C1 T1 CC L1 L2 2 9/16 5 5/8 6 5/8 3 1/4 57 3/8 SHAFT LENGTH 50 15/ /16 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 21 3/4 21 3/4 21 3/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07005, TIB07006 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.0 with frame reference of 0 Page 26 of 29 1apr17jh
27 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 191.0" stretch from 159 VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.6L DIESEL SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 5.9 TRANSMISSION= 3.0 CHASSIS BRACKET= -0.5 L2 UNLOADED WITH BODY (±1.0 ) = 4.4 L1= 3.5 RETARDER= 4.0 L2 LOADED (±1.0 ) = 2.9 AXLE= 4.0 A B1 C1 T1 CC L1 L /8 7 1/ /8 SHAFT LENGTH 54 15/ /16 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 21 3/4 21 3/4 23 1/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07003, TIB07004 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.0 with frame reference of 0 Page 27 of 29 1apr17jh
28 VEHICLE TECHNICAL DATA CHASSIS MAKE / MODEL CHEVROLET G4500 CUSTOMER: WHEELBASE 191.0" stretch from 159 VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.0L GASOLINE SPEED SWITCH / INTERFACE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION SHUTTLE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 1/4 Dv unloaded: 11 3/4 D chassis only: 13 1/4 L2 CHASSIS ONLY (±1.0 ) = 6.3 TRANSMISSION= 4.5 CHASSIS BRACKET= -0.5 L2 UNLOADED WITH BODY (±1.0 ) = 4.8 L1= 3.5 RETARDER= 4.0 L2 LOADED (±1.0 ) = 3.4 AXLE= 4.0 A B1 C1 T1 CC L1 L2 2 9/16 5 7/8 6 7/8 3 1/2 61 3/8 SHAFT LENGTH 54 15/ /16 S1 S2 S4 SR R1 SHAFT MINIMUM TUBE DIAMETER /4 21 3/4 21 3/4 21 3/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS NOTE 1: Drive shaft lengths are measured from center of U-joint and are installed lengths. angle tolerance=±0.2 NOTE 2: All drive shafts must be dynamically balanced after modification. dimension tolerance=±1/16" NOTE 3: Always verify proper shaft lengths before modification NOTE 4: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 5: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 6: adjust retarder to angle indicated by rotating chassis bracket NOTE 7: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 8: USE BRACKETS TIB07000e, TIB07005, TIB07006 NOTE 9: Check axle angle after body is installed and if necessary adjust to 4.0 with frame reference of 0 Page 28 of 29 1apr17jh
29 VEHICLE TECHNICAL DATA CUSTOMER: CHASSIS MAKE / MODEL CHEVROLET G4500 CHASSIS VIN: WHEELBASE 191.0" 159 stretch after x-member VEHICLE NUMBER ENGINE MAKE / MODEL CHEVROLET 6.0L GASOLINE CONTROL MODULE TRCM TRANSMISSION MAKE / MODEL CHEVROLET 6L90 TIRE SIZE 225/75R-16 AXLE MAKE / MODEL AAM GVW / GCW lbs DRIVE TYPE 4X2 BRAKES HYD RETARDER MODEL AF50-55 ABS RETARDER PART NUMBER LFA AXLE RATIO 4.10 RETARDER SERIAL NUMBER DRIVE LINE SERIES 1485 RETARDER CONTROL SYSTEM FOOT FLANGE YOKE MILEAGE AT TIME OF INSTALL SUSPENSION TYPE SPRING HOURS AT TIME OF INSTALL VOCATION REFUSE Note: If any of the above mentioned factors vary with your application, please call our TECHNICAL DEPARTMENT. Dc loaded: 10 4/16 Dv unloaded: 11 12/16 CHASSIS BRACKET= 0.0 L3 CHASSIS ONLY (±1.0 ) = 6.3 TRANSMISSION= 4.5 RETARDER= 4.5 L3 UNLOADED WITH BODY (±1.0 ) = 4.2 L1= 4.0 L2= 4.0 L3 LOADED (±1.0 ) = 2.1 AXLE= 4.0 A B1 C1 P T1 CC L1 L2 L3 2 9/16 4 5/8 5 11/ /16 2 5/ /8 SHAFT LENGTH 29 7/8 43 1/ /16 S1 S2 SR S6 S4 R1 SHAFT MINIMUM TUBE DIAMETER /4 21 3/4 21 3/4 21 3/4 21 3/4 13 1/16 SHAFT MINIMUM TUBE THICKNESS CAUTION: angle tolerance=±0.2 NOTE 1: L1, L2 and L3 are measured from center of U-joint and are installed lengths. dimension tolerance=±1/16" NOTE 2: All drive shafts must be dynamically balanced after modification. NOTE 3: When not specified, the front & the rear drive shafts, on each retarder side, must have at least the same slip as the original drive shaft NOTE 4: When not specified, the flange yoke on each retarder side must have the maximum working angle capacity available in the driveline series concerned. NOTE 5: After installation is completed, measure drive shaft angles and compare to the angles on the installation drawing. Contact TELMA Customer Support Engineering if the angles measured do not conform to the drawing NOTE 6: USE BRACKETS TIB07000, TIB07005, TIB07006 NOTE 7: adjust retarder to angle indicated by rotating chassis bracket NOTE 8: ADJUST CARRIER BEARING SO THAT SECOND SHAFT SHAFT (L2) IS 4.0 NOTE 9: ADJUST CARRIER BEARING SO THAT OFFSET MATCHES TELMA OFFSET NOTE 10: Check axle angle after body is installed and if necessary adjust to 4.0 with frame reference of 0 Page 29 of 29 1apr17jh
TL INSTALLATION MANUAL FOR TELMA AF50-55 ON CHEVROLET G4500 CUTAWAY 6.0L GASOLINE WITH ROTARY FOOT SWITCH
INSTALLATION MANUAL FOR TELMA AF50-55 ON CHEVROLET G4500 CUTAWAY 6.0L GASOLINE WITH ROTARY FOOT SWITCH 6nov15jh 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 1.3 Fuel Tank 2 Telma Installation
More informationTL INSTALLATION MANUAL FOR TELMA AF50-55 ON FORD E-350/450 CUTAWAY with rotary foot switch design 2 including MY2016 changes
INSTALLATION MANUAL FOR TELMA AF50-55 ON FORD E-350/450 CUTAWAY with rotary foot switch design 2 including MY2016 changes 10nov16jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust
More informationTL INSTALLATION MANUAL FOR TELMA AF50-90 with ROTARY FOOT SWITCH DESIGN 2 FORD F550 CAB CHASSIS FROM MODEL YEAR 2011
INSTALLATION MANUAL FOR TELMA AF50-90 with ROTARY FOOT SWITCH DESIGN 2 FORD F550 CAB CHASSIS FROM MODEL YEAR 2011 1sep16jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 1.3 Fuel
More informationTL INSTALLATION MANUAL FOR TELMA AD50-90 ON FORD F550 CAB CHASSIS FROM MODEL YEAR 2011 WITH ROTARY FOOT SWITCH
INSTALLATION MANUAL FOR TELMA AD50-90 ON FORD F550 CAB CHASSIS FROM MODEL YEAR 2011 WITH ROTARY FOOT SWITCH 11nov14jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 1.3 Fuel Tank
More informationTL INSTALLATION MANUAL FOR TELMA AF50-55 ON FORD E-350/450 CUTAWAY
INSTALLATION MANUAL FOR TELMA AF50-55 ON FORD E-350/450 CUTAWAY 21nov13jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 2 Telma Installation 2.1 Installation Kit TIK10678 2.2
More informationPreface - Scope of this manual 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust
INSTALLATION MANUAL FOR TELMA AF50-90 ON NAVISTAR IC BUS CHASSIS WITH SPL100 U-JOINTS and CUMMINS ENGINE SINGLE CANISTER EXHAUST USING ROTARY FOOT SWITCH FOR HYDRUALIC BRAKES OR OPTIONAL PRESSURE TRANSDUCER
More informationTL INSTALLATION MANUAL FOR TELMA AD50-90 WITH SPEED SWITCH ON FORD F550 CAB CHASSIS FROM MODEL YEAR 2011
INSTALLATION MANUAL FOR TELMA AD50-90 WITH SPEED SWITCH ON FORD F550 CAB CHASSIS FROM MODEL YEAR 2011 26oct11jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 1.3 Fuel Tank 1.4
More informationTL INSTALLATION MANUAL FOR TELMA AC50-55 ON FORD E-350/450 CUTAWAY WITH TELMA CONTROL MODULE
INSTALLATION MANUAL FOR TELMA AC50-55 ON FORD E-350/450 CUTAWAY WITH TELMA CONTROL MODULE 17feb12jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 2 Telma Installation 2.1 Installation
More informationTechnical Service Bulletin
SUBJECT: Procedure to upgrade to new rotary foot switch TIG31066 on Navistar chassis Products Affected: All Navistar vehicles MY2008 and newer with hydraulic brakes Effective Date: 20oct15 Telma is committed
More informationTL UNIVERSAL WIRING GUIDELINE TRCM - J jan18jh
UNIVERSAL WIRING GUIDELINE TRCM - J1939 31jan18jh 1 Control Kits TABLE OF CONTENTS 1.1. TIK10103 Universal Automatic Foot Control for Hydraulic Brakes 1.2. TIK10104 Universal Automatic Foot Control for
More informationTL UNIVERSAL WIRING PROCEDURE
UNIVERSAL WIRING PROCEDURE 3nov11jh TABLE OF CONTENTS 1 Control Kits 1.1. TIK10100 Universal Manual Hand Control 1.2. TIK10103 Universal Automatic Foot Control for Hydraulic Brakes 1.3. TIK10104 Universal
More informationSelection Guide TL TL117000
TL117000 Selection Guide Page 1 of 25 Telma Retarder Inc. Toll Free: 800.797.7714 (USA only) Tel: 847.593.1098 Fax: 847.593.3592 www.telmausa.com 1. GENERAL INFORMATION 1.1 Comparison Matrix of Secondary
More informationONLY AFTER ALL MEASUREMENTS HAVE BEEN TAKEN. Remove any components in the chassis that may interfere with the retarder and/or mounting hardware.
Tools Needed Transmission jack Hand held calculator Mechanics hand tools Torque wrench (up to 250 lb.-ft) ½ heavy duty drill or frame drill Tape measure Straight edge Electronic Angle meter (Spicer Anglemaster
More informationSelection Guide TL TL117000
TL117000 Selection Guide Telma Retarder Inc. 870 Lively Blvd Wood Dale Illinois 60191 Toll Free: 800.797.7714 Tel: 847.593.1098 Fax: 847.593.3592 www.telmausa.com Page 1 of 26 TABLE OF CONTENTS 1. GENERAL
More informationTL REPAIR MANUAL. Telma model FV61-00 (FU831310) replacement on Dana 19060S axle. Page 1 of 8 30jun10
TL103035 REPAIR MANUAL Telma model FV61-00 (FU831310) replacement on Dana 19060S axle Page 1 of 8 30jun10 Exploded view TL103035 Stator carrier Telma Unit Flange Yoke Page 2 of 8 30jun10 Disassembly 1.
More informationPart Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Flow Sensor 4001356 1 Deflector plate 2000612-1 1
More informationTL (TIL03029) REPAIR MANUAL. Telma model FN72-40 replacement on Arvin Meritor forward tandem carrier. Page 1 of JUL-11.
REPAIR MANUAL Telma model FN72-40 replacement on Arvin Meritor forward tandem carrier Page 1 of 10 29-JUL-11 Exploded view P/N: FE962100 Stator Carrier Kit Includes: Qty Description Telma P/N 1 Stator
More informationPFadvantage Metalfor Araus 1360
Metalfor Araus 1360 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor Araus 2005300-14 1 Display Bracket 4000134
More informationOWNERS MANUAL. GMC C K AND 19K GVW CHASSIS CAB 2004-NEWER MODELS (Link Part No. 8M000050) PROUDLY INSTALLED BY : COMPANY : INSTALLER SIGNATURE :
OWNERS MANUAL GMC C5500 15K AND 19K GVW CHASSIS CAB 2004-NEWER MODELS (Link Part No. 8M000050) Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 (712) 722-4868 Fax (712) 722-4779 QUESTIONS?
More informationRostselmash Torum 740
Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part Number 740 Combine Kit Torum 740 4100762 1 Threaded Arm Assembly 2000311-2 1 Header
More informationFlow Sensor
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Quick reference sheet 2002831-36 1 Installation instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----1075 North Ave. Sanger, CA 93657-3539 toll free: 800-445-3767 web: www.belltechcorp.com---- 6419 HANGER & SHACKLE KIT FORD F-150 Congratulations! You were selective enough
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----1075 North Ave. Sanger, CA 93657-3539 toll free: 800-445-3767 web: www.belltechcorp.com---- 6907 REAR LOWERING KIT 97-00 CHEVY 1-TON C-3500 Congratulations! You were selective
More informationInstallation Instructions. 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK GM 2WD C1500 P/U ONLY
Installation Instructions 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK 2007-13 GM 2WD C1500 P/U ONLY 2007-13 GM 1500 Truck Basic System FTS21060BK / FTS21061BK / FTS21042BK 2007-13 GM 2WD C1500
More informationOWNERS MANUAL GM C4500/C5500 4X4 DANA MODEL S135 REAR AXLE 2005-NEWER MODELS LINK MFG. PART NO. 8M PROUDLY INSTALLED BY : COMPANY :
OWNERS MANUAL GM C4500/C5500 4X4 DANA MODEL S135 REAR AXLE 2005-NEWER MODELS LINK MFG. PART NO. 8M000060 Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 (712) 722-4874 Fax (712) 722-4876
More informationAccessory Harness & Bracket Kit
Accessory Harness & Bracket Kit Stainless Steel Hopper Spreader Gas 9969 June 5, 06 Lit. No. 98986, Rev. 0 PARTS LIST 9 4 8 7 6 4 3 8 VIB LIGHT STROBE PREWET 5 0 4 9969 Accessory Harness & Bracket Kit
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More information2-row and All-row systems included.
Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown above correspond
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----1075 North Ave. Sanger, CA 93657-3539 toll free: 800-445-3767 web: www.belltechcorp.com---- 6420 SHACKLE & HANGER KIT FORD F-350 Congratulations! You were selective enough
More informationPFadvantage MF 6850/6855; Ideal 9080/9090
MF 6850/6855; Ideal 9080/9090 Note: Indented items indicate parts included in an Quantity by Model assembly listed above MF Ideal Part Name/Description Part Number 6850 6855 9080 9090 Instruction Kit MF
More informationJOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP)
P. 1 of 5 JOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP) Note: Harness Extension Kit Required for 4 Passenger (p/n: 1XUV4WHEK) This manual is the property of the
More informationINSTALLATION INSTRUCTION 88088
INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More informationROADRELAY 5 Installation Guide
ROADRELAY 5 Installation Guide ROADRELAY 5 Installation Guide Bulletin No. 4971214 Revision A Copyright 2011, Cummins Inc. All rights reserved. Cummins Inc. shall not be liable for technical or editorial
More informationSpreader and Vehicle Battery Kits
May 5, 20 Lit. No. 922, Rev. 04 and Vehicle Battery Kits Hopper s Parts List and Installation Instructions CAUTION Read this document before installing the and Vehicle Battery Kit. CAUTION Use standard
More informationInstallation Instructions for John Deere cotton picker models: 9986 & 2-row and All-row systems included.
Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 9986 & 9996 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown
More informationMOUNTING RAILS ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
10/30/2017 PAGE 1 OF 6 Parts List ITEM QTY PART NUMBER DESCRIPTION 1 2 CM-16150-MR MOUNTING RAILS 2 2 CM-16150-FB.375" FRONT BRACKET 3 1 CM-16150-PSRB.375" PASSENGER SIDE REAR BRACKET 4 1 CM-16150-DSRB.375"
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2013 MDX Publications No. BII 13442 Issue Date JULY 2012 PARTS LIST Receiver cover Trailer hitch Hitch pin Left bracket Hitch pin clip Trailer Harness
More informationINSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE
INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE LAST UPDATED: April 2018 Thank you for choosing the Motor Trike Electric Reverse. We ask that you read the directions before you start and follow
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 39889 HITCH 2009 MDX Issue Date JULY 2008 PARTS LIST Trailer Hitch Kit P/N 08L92-STX-200 Trailer Harness Kit P/N 08L91-STX-200 Trailer
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More informationIdle Timer Controller - ITC515-A Ford Transit Contact InterMotive for additional vehicle applications
An ISO 9001:2008 Registered Company Idle Timer Controller - ITC515-A 2015-2018 Ford Transit Contact InterMotive for additional vehicle applications Overview The ITC515-A system will shut off gas or diesel
More informationITCEMS950 Idle Timer Controller - Engine Monitor Shutdown Isuzu NPR 6.0L Gasoline Engine
Introduction An ISO 9001:2008 Registered Company ITCEMS950 Idle Timer Controller - Engine Monitor Shutdown 2014-2016 Isuzu NPR 6.0L Gasoline Engine Contact InterMotive for additional vehicle applications
More informationFRONT DRIVELINE MODIFICATION MAY BE NECESSARY!!!!
INSTALLATION INSTRUCTIONS FOR 2009 DODGE 2500/3500 4WD & 1500 Mega Cab 6 SUSPENSION SYSTEM PART NUMBER 7206 Requires the following parts (sold separately) for a complete installation: Front Coil Spring
More informationOWNERS MANUAL GM C4500/C5500 DANA MODEL S135 REAR AXLE 2003-NEWER MODELS LINK MFG. PART NO. 8M PROUDLY INSTALLED BY : COMPANY :
OWNERS MANUAL GM C4500/C5500 DANA MODEL S135 REAR AXLE 2003-NEWER MODELS LINK MFG. PART NO. 8M000030 Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 (712) 722-4874 Fax (712) 722-4876 QUESTIONS?
More informationInstallation Guide CLAAS Lexion Combines with 9 inch Elevators
Installation Guide CLAAS Lexion Combines with 9 inch Elevators 955614_01 4/17 1 Table of Contents System Overview 3 Quick Start Guide 4 Flow Sensor Installation 5 Hydraulic Elevator Adjustment Kit Installation
More informationLGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions
LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative connections
More informationHARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM. Parts List and Installation Instructions CAUTION
May 1, 2018 Lit. No. 92991, Rev. 00 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM Parts List and Installation Instructions Read this document before installing the snowplow. See your sales outlet/website
More information»Product» Safety Warning
#F2622 Installation Instructions 1997-2003 Ford F-150 4WD 6" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationSide Door Sill Trim Plate Package Installation
Page 1 of 5 2014 Chevrolet Equinox Equinox, Terrain VIN L Accessory Installation Manual Accessories Interior Accessories Accessories Document ID: 3619390 Side Door Sill Trim Plate Package Installation
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-250-M2 ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More informationC FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY
EXHAUST BRAKES C40019 1999-2003 FORD F250 / F350 7.3L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY Getting Started Thank you and congratulations on your purchase of a Pacbrake exhaust retarder.
More informationINSTALLATION INSTRUCTION 88146
INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationSuspension System RS6582B
Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance
More informationSCION tc Navigation System Preparation. Part Number: PT
Preparation Part Number: PT611-21111 Kit Contents Item # Quantity Reqd. Description 1 1 Navigation System 2 1 GPS Antenna 3 1 Bluetooth Antenna 4 1 Wire Harness (Reverse / Park Brake) 5 1 RCA Relay Cable
More informationOwner smanual. Banks Monster Split-Dual Exhaust System Ford Power Stroke 6.0L Turbo-Diesel F250/F350 Trucks. with Installation Instructions
Owner smanual with Installation Instructions Banks Monster Split-Dual Exhaust System 2003-2007 Ford Power Stroke 6.0L Turbo-Diesel F250/F350 Trucks THIS MANUAL IS FOR USE WITH Systems 47600-47614, 48761,
More informationTOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation
Preparation Part Number: PT738-48080 Kit Contents Item # Quantity Reqd. Description 1 1 Driver Side Running Board 2 1 Passenger Side Running Board 3 4 /Middle Mount Bracket 4 2 Rear Mount Bracket 5 2 Rear
More informationINSTALLATION INSTRUCTION 88051
INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT
More informationLexion 570R/575R, 580R/585R, 590R/595R
Note: Indented items indicate parts included in an assembly listed above Quantity by Model 2006+ All Years Part Name/Description Part Number 570R 575R 580R 585R Instruction Kit Lexion 570/580/590 2005500-5
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----3300 W. Pontiac Way Clovis, CA 93612 toll free: 1-800-445-3767 web: www.belltech.com---- 6605-6607 FLIP KIT CHEVROLET C/K 1500 / 2500 PICK UP Thank you for being selective
More informationHARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM
October 1, 2018 Lit. No. 92988, Rev. 00 72199 HARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM Parts List and Installation Instructions Read this document before installing the harness kit. See your sales
More informationFord 6.7L Installation of the Guardian Safety System
Ford 6.7L Installation of the Guardian Safety System Diesel Tech Industries Ltd. 14215-120 Avenue Edmonton, Alberta, Canada T5L 2R8 Phone: (780) 455-9876 info@dtiguardian.com www.dtiguardian.com DTI05-02.01/13
More informationFAX
INSTALLATION INSTRUCTIONS 6299 Air Suspension Kit (pat. pending) 2009+ Dodge 1500 Pickup with Rear Coil Springs Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationIdle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana
An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2018 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications Introduction The A-ITC620-A1 is an
More informationPRODUCT SAFETY NOTICE DEALER/INSTALLER NOTICE
PRODUCT SAFETY NOTICE Congratulations. This vehicle has been equipped with a Firestone air suspension system. This suspension will enhance the vehicle s handling when loaded, however, the vehicle s performance
More informationIdle Timer Controller - A-ITC520-A Ford E Series Ford F250 - F Ford F250 - F550 (*B-ITC520-A) F650/F750
An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC520-A 2009-2018 Ford E Series 2008-2016 Ford F250 - F550 2017-2018 Ford F250 - F550 (*B-ITC520-A) 2016-2018 F650/F750 *Uses the Ford 24-Pin
More information2015 Ford F150 Rear Bumper w/ LED
2015 Ford F150 Bumper w/ LED T527990 T527991 PARTS LIST: 1 Bumper Assembly 4 12mm Lock Washers 2 Mounting Brackets 6 12 mm Nylon Lock Nuts 4 Sensor Hole Plugs 8 4mm x 10mm Button Head Bolts 2 Plastic Plugs
More informationLokar Cable Operated Sensor Kit Installation Instructions For Ford C4 and C6
Lokar Cable Operated Sensor Kit Installation Instructions For Ford C4 and C6 Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Lokar Cable Operated
More informationInstallation Instructions. Instinct Shock Controller. Part # Instinct Shock Controller. Installation Instructions
Part # 82010013 - Instinct Shock Controller Instinct Shock Controller Installation Table of contents Page 2... Included components Page 3... ECU Installation Page 4... GSensor Installation Page 5... Sensors
More informationCONTENTS... 2 SYSTEM OPERATION...
D11274 Rev N 7/18 Contents CONTENTS... 2 INTRODUCTION... 3 SUSPENSION RATING... 3 SERIAL NUMBER TAG INFORMATION... 3 VEHICLE TOWING AND JACKING INFORMATION... 3 HYDRAULIC FITTING ASSEMBLY... 5 SAE O-Ring
More information29048, 29049, 29050, 29051, 29052, 29053, 29054,
April 15, 2014 Lit. No. 29225, Rev. 11 29048, 29049, 29050, 29051, 29052, 29053, 29054, 29400 5 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM w/2 PLUG SYSTEM HARNESSES Installation Instructions Read
More informationInstallation Manual P / P / P A / P B / P C E N G I N E B R A K E S
Manual A p p l i c a t i o n : D e t r o i t D i e s e l S e r i e s 6 0 P - 6 1 / P - 6 3 / P - 6 3 A / P - 6 3 B / P - 6 3 C E N G I N E B R A K E S 5 If the engine is equipped with an aluminum valve
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More information2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014
2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &
More informationDirectMount EXHAUST BRAKES
DirectMount EXHAUST BRAKES APPLICATION: Fixed Orifice and PRXB Exhaust Brakes 2003 2005 Dodge Trucks with 3.5" & 4" Exhaust and 47RE & 48RE Automatic Transmissions Only Vehicles with an existing air compressor
More informationTOYOTA 4-RUNNER TOWING HITCH Preparation
Preparation Part Number: PT228-89460 Kit Contents 1 1 High Assembly 2 1 Wiring Harness Bracket 3 1 Hardware Bag 4 1 Hitch Cover 5 2 Frame Spacer 6 2 Center Spacer 7 1 Close-out Panel Hardware Bag Contents
More information8436, 8437, 8438, 8439, 8442, 27480, 27780, 28028, & ISOLATION MODULE ELECTRICAL SYSTEM
September 11, 2003 Lit. No. 27808 8436, 8437, 8438, 8439, 8442, 27480, 27780, 28028, & 28400 ISOLATION MODULE ELECTRICAL SYSTEM Installation Instructions Read this document before installing the snowplow.
More information'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS
1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 28632 TRAILER HITCH 2006 RIDGELINE Issue Date FEB 2005 PARTS LIST Receiver cover Trailer Hitch Kit: P/N 08L92-SJC-100 Trailer hitch
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More informationLower Adjuster Small Black Header Sensor Reversed
Parts List for Combine Quantity by Model Early Late Early Late Note: Indented items indicate parts included M M M M M M in an assembly listed above F F F F F F 7 7 8 8 8 8 5 6 5 5 6 6 Part Name/Description
More informationINSTALLATION & OWNER S MANUAL
1 of 18 INSTALLATION & OWNER S MANUAL (*Not including cab & other accessories) A/C Alternator Kit: Yamaha Drive & Drive2 P/N: 1ACYDR2DRK Recommended it be installed with Curtis Cab: Sandstone (p/n 1GCYD1-A,
More informationIdle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana
Introduction An ISO 9001:2015 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2019 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications The A-ITC620-A1 is an
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More informationINSTALLATION INSTRUCTIONS
Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness
More informationTrike Conversion Installation Manual. All Models
Trike Conversion Installation Manual For Honda VTX 1300 Motorcycles All Models Revision 4 Mar. 2011 CAUTION: Failure to follow these instructions can lead to serious personal injury and/or property damage
More informationC40008 & C40009 EXHAUST BRAKES
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
More informationSCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT
Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface
More information29048, 29049, 29050, 29051, 29052, 20953, 29054,
July 15, 2008 Lit. No. 29225, Rev. 06 29048, 29049, 29050, 29051, 29052, 20953, 29054, 29400-2 HARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM w/2-plug SYSTEM HARNESSES Installation Instructions Read
More informationINSTALLATION INSTRUCTION 88581
INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension
More informationPOWERED RUNNING BOARDS INSTALLATION MANUAL
POWE RUNNING BOARDS INSTALLATION MANUAL Level of Difficulty Moderate Parts List 1 Driver / left running board* 1 Passenger / right running board* 4 Mounting bracket, standard 2 Mounting bracket, middle
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 6612/6616 & 6614/6618 REAR AXLE FLIP-KIT 1999-UP CHEVROLET SILVERADO/GMC SIERRA 1500 Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent many
More informationIntelligent Lift Interlock ILISCT511-A (Manual Lift Door) Ford Transit Connect
An ISO 9001:2000 Registered Company Intelligent Lift Interlock ILISCT511-A (Manual Lift Door) 2010-2013 Ford Transit Connect Introduction The ILISCT511 is a microprocessor driven system for controlling
More information2015 Ford F150 Front Bumper w/ LED
PARTS LIST: 2015 Ford F150 Bumper w/ LED 1 Bumper Assembly 4 8mm Lock Washers 1 Driver/left L Bracket (center LED light) 2 8mm Hex Nuts 1 Passenger/right L Bracket (center LED light) 2 6mm x 20mm Button
More information4WD RANGER/BRONCO II WD EXPLORER CLASS II INSTALLATION INSTRUCTIONS
4WD RANGER/BRONCO II 8-97 4WD EXPLORER 90-94 CLASS II INSTALLATION INSTRUCTIONS Before beginning the installation, read these instructions and the enclosed driver s WARNING NOTICE thoroughly and completely.
More informationMF 9690, 9790, Challenger 660, 670
Ag Leader Technology Parts List Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No. MF 9690 MF 9790 Challenger 660 Challenger 670 Instruction
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ----1075 North Ave. Sanger, CA 93657-3539 toll free: 800-445-3767 web: www.belltechcorp.com---- 5052 AIR JACK 94-99 DODGE ½ TON RAM C-1500 Congratulations! You were selective
More informationC-10 INSTALLATION INSTRUCTIONS
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 30,000 LBS. TRAILER WEIGHT & 6,000 LBS. TONGUE WEIGHT. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** Parts List ITEM
More informationAssembly, Installation, Operation and Maintenance Instructions. Base Rail Bracket Kit. For updates see PRODUCT SUPPORT tab at
Assembly, Installation, Operation and Maintenance Instructions P/N: 32831 Base Rail Kit For updates see PRODUCT SUPPORT tab at www.huskytow.com Provide a copy of these Instructions to the end user of this
More information