The filters for hydraulic fluids are used to protect each component in a hydraulic circuit. Port size. Micromesh 74, 105, 149

Transcription

1 Hydraulic ilters H Series The filters for hydraulic fluids are used to protect each component in a hydraulic circuit. RoHS H Series Operating Port size Element (µm) nominal filtration Accessory (Option) Page Vertical Suction ilter HIA Series Suction ilter with Case H99 Series Suction Guard HG Series Line ilter H34/44/54/64 Series Vertical Return ilter HBA Series Return ilter H100 Series Oil ilter H0 Series 3.5, 7, 14, 21 MPa 1.6 MPa 1 MPa 1 MPa 2, 2 1/2, 3, 3 1/2, 4 2, 2 1/2, 3, 3 1/2, 4 2, 2 1/2, 3 3/8, 1/2, 3/4, 1, 1 1/4 1 1/2, 2, 2 1/2, 3 3/4, 1 1/4, 1 1/2 3/4, 1, 1 1/4, 1 1/2, 2 2 1/2, 3 1/4, 3/8, 1/2 () 74, 105 () Air breezer Cap Bracket Magnetic Separator HM Series

2 Vertical Suction ilter HIA Series RoHS No air pockets There are no places for air pockets to form. This prevents damage to the pump and enables normal operation to start immediately. Elimination of all collected matter All collected matter can be disposed of reliably when the element is replaced. There is no danger of collected matter dropping back into the tank. No drain port required The structure of the filter does not contain areas for drain fluid to collect, so there is no need to manually drain the pump. Easy element replacement Simply open the cover to quickly replace the element without touching the pipes. The element is extracted from the top, so no fluid can leak out. Compact and lightweight The compact and lightweight design employs an aluminum casted housing. Clogging sensor The sensor indicates when the element is becoming clogged, facilitating maintenance and helping to avoid pump damage, such as cavitations. ifferential indicator/reset type switch/visual combined, non-reset type Specifications luid Operating Operating temperature Cover/Case Main material O-ring Seal Material Element Nominal filtration ifferential resistance ifferential indicator operating (Element replacement differential ) Hydraulic fluid 80 C Aluminum casting NBR or KM Note) NBR or EPM Note) Stainless steel, Carbon steel, Aluminum, Epoxy resin µm (200, 0, 100 mesh) 0. MPa 20.0 kpa Relief valve open 26.7 kpa Note) The material of the O-rings and seals differs depending on the hydraulic fluid used. Petroleum, Water-glycol, Emulsion: NBR; Phosphoric ester: KM, EPM Model/Rated low Rate Model lange port size Note) Rated flow rate (L/min) HIA - 1/2 B 30 HIA -06 3/4 B 50 HIA B 95 HIA /4 B 0 HIA /2 B 220 HIA - 2 B 350 HIA /2 B 550 HIA B 770 HIA /2 B 1000 HIA B 1300 The symbol represented by indicates the type of applicable hydraulic fluid. N: Petroleum, W: Waterglycol, Emulsion, V: Phosphoric ester Note) itted with companion flange. (lange configuration is exclusive to SMC.) Accessory/Option escription Part no. Note ifferential indicator CB-56H Petroleum, Water-glycol, Emulsion CB-56H-V Phosphoric ester switch CB-57H Petroleum, Water-glycol, Emulsion (N.C. and N.O. common) CB-57H-V Phosphoric ester AG-12H Petroleum (for differential indication AG-12H-W Water-glycol, Emulsion part) AG-12H-V Phosphoric ester low Rate Characteristics Pressure drop (kpa) low rate (L/min) Conditions luid: Turbine oil Class 2 VG56 Viscosity: 45 mm 2 /s ilter material: Nominal filtration: 74 µm to 149 µm

3 Vertical Suction ilter HIA Series Vertical suction filter How to Order H I A N M 074 M R N W V Hydraulic fluid Petroleum Water-glycol, Emulsion Phosphoric ester Replacement Element Part No. 74 µm Port size (200 mesh) (1/2 B ) 06 (3/4 B ), 08 (1 B ) 10 (1 1/4 B ), 12 (1 1/2 B ) (2 B ) 20 (2 1/2 B ), 24 (3 B ) 28 (3 1/2 B ), 32 (4 B ) EM001H-074N EM101H-074N EM201H-074N EM301H-074N EM401H-074N EM501H-074N Port size /2 B 3/4 B 1 B 1 1/4 B 1 1/2 B 2 B 2 1/2 B 3 B 3 1/2 B 4 B Note) or flange connection only. 105 µm (0 mesh) EM001H-105N EM101H-105N EM201H-105N EM301H-105N EM401H-105N 149 µm (100 mesh) EM001H-149N EM101H-149N EM201H-149N EM301H-149N EM401H-149N EM501H-149N EM501H-105N Note 1) The symbol at the end of the element part no. indicates the hydraulic fluid type. N: Petroleum, Phosphoric ester, W: Water-glycol, Emulsion. Note 2) Above elements require one element per filter Element M M ifferential indicator E switch Note) None () Note) N.C. and N.O. common Nominal filtration Element size ø65 x 90 ø85 x 110 ø100 x 0 ø120 x 180 ø140 x 200 ø180 x µm 105 µm 149 µm Relief valve R With relief valve None (Blanking plate) H A differential indicator or a differential indication switch can be selected, and mounted on all filter models. ifferential indicator Operating 20 kpa Once a value is displayed, it will continue to be displayed until reset, even if the pump is stopped. (Reset type) Perform element replacement when the red ring floats up and covers the entire view port. ifferential Pressure Indication switch Operating 20 kpa When a value has been displayed, it will be automatically reset when the pump is stopped. (Non-reset type) This is a visual dual-purpose. Perform element replacement when the switch has actuated (when the red ring floats up and covers the entire view port). N.C. and N.O. common Refer to page 529 for Microswitch for differential indication switch. Reset button View port COM. N.O. N.C. View port G1/2 499

4 HIA Series Construction/Seal List ifferential indicator Hexagon socket head cap screw Cover Case w O-ring Wave washer q O-ring ifferential indication switch Relief valve Element e O-ring switch A r Base seal e O-ring Companion flange Hexagon head bolt IN Replacement O-ring/Seal List (One each of the seal and O-ring types listed below are required per filter.) Port size Applicable hydraulic fluid Material q O-ring order no. w O-ring order no. e O-ring order no. r Base seal order no. KA064 KA00061 KA058 (G35) (G30) AL-196H KA066 KA060 KA to 08 (G90) (G50) (G45) AL-197H KA053 KA063 KA to 12 Petroleum, AL-198H (G105) (G65) (G55) Water-glycol, NBR-70-1 KA00787 KA065 KA064 Emulsion AL-199H (G80) KA00060 KA052 KA to 24 (G145) (G100) (G95) AL-200H KA00792 KA00790 KA to 32 (G185) (G140) AL-201H KA006 KA00696 KA00695 (G35) (G30) AL-196H-V KA007 KA00699 KA to 08 (G90) (G50) (G45) AL-197H-V KA00688 KA00614 KA to 12 KM-70 AL-198H-V (G105) (G65) (G55) Phosphoric ester or KA00689 KA00702 KA006 EPM-70 AL-199H-V (G80) KA00692 KA00610 KA to 24 (G145) (G100) (G95) AL-200H-V KA00693 KA00691 KA to 32 (G185) (G140) AL-201H-V Note) The material of seals (AL-196H-V to AL-201H-V) is EPM-70. Note) The material and nominal size notations are based on JISB2401. q Mounting Confirm IN and before connecting. or maintenance, make sure to provide sufficient space above the filter for removing the element. 500 Replacement parts escription Applicable model HIAN Companion flange set HIAW HIAV Note 1) The two digit number of the port size is entered in the of the part number. Note 2) Part number N: O-ring material NBR, V: O-ring material KM Handling Precautions w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential indicator or the switch may activate. If this occurs, wait until the oil temperature rises by a warm-up operation, then check if this is caused by clogging. If the differential indicator is the reset type, make sure to reset it after normal operation starts in cold weather such as during winter. When using a differential indication switch, if a filter clogged signal is incorporated into the sequence circuit of the machine, make sure to design the system so the filter clogged signal does not operate until normal operation starts. Part no. HIA-L003N- HIA-L003V- Set contents Two sets each of companion flange, O-ring, hexagon head bolts e Element replacement When the difference reaches 20 kpa during filter operation (actuating the differential indicator), stop operation and either wash or replace the element. If any scratches or damage are found on the O-ring during assembly/disassembly, replace with a new O-ring. When washing the element, do not wipe it using a stiff brush or rag. After washing the element, make sure the base seal is properly mounted.

5 Vertical Suction ilter HIA Series imensions ifferential indicator ø B (34) C H H E Removal dimension K switch 62 (65) 4 x I øa øj G IN H (mm) Model HIA - HIA -06 HIA -08 HIA -10 HIA -12 HIA - HIA -20 HIA -24 HIA -28 HIA -32 A B C E G H I M8 x 25 M8 x 25 M10 x 30 M12 x 35 M12 x 35 M x 40 J K Weight (kg)