ADDENDUM #1, POSTED 12/27/17 RFQ# X4 ONE TON CHASSIS CAB DUALLY

Transcription

1 ADDENDUM #1, POSTED 12/27/17 RFQ# X4 ONE TON CHASSIS CAB DUALLY The current RFP states the following: The Marinette County Highway Department is requesting sealed quotes for one x4 Standard One Ton, Chassis Cab Dually, to be delivered to the Marinette County Highway Shop, 501 Pine Street, Peshtigo, WI Corrected language: The Marinette County Highway Department is requesting sealed quotes for one x4 Standard One Ton, Chassis Cab Dually, to be delivered to the successful service body dealer.

2 Page 2 of 16

3 ATTACHMENT A - REVISED RFQ# TWO (2) 2018 TRI-AXLE CAB & CHASSIS WITH TRADE IN OPTIONS BID TABULATION SHEET MAKE: MODEL: YEAR: DELIVERY DATE F.O.B. TO BODY DEALER The earliest delivery date is a deciding factor as to successful proposer. Note: Proposer is responsible for delivery of cab & chassis to Body Dealer. 1. ENGINES: 12-15L, min 425hp, RPM w/front PTO set up, Cummins preferred Note: Standard warranties to be the same as found on pages of quote package MAKE MODEL: RATED RPM & TORQUE 2. OEM AIR SUSPENSION SYSTEM: (all axle specifications to be the same as on page 9): Capacity at ground: 46,000 lb. minimum Capacity Make Model Describe Air Suspension System: CAB & CHASSIS SPECIFICATIONS: The following aluminum, galvanized or steel cab and chassis series are acceptable for quote: Specify: Aluminum Galvanized Other (specify) Specify Cab and Chassis Model: All components shall have a minimum of 20" ground clearance and shall be located so as not to interfere with the placement of an under body scraper. COMPLIES MINIMUM CAB SPECIFICATIONS: YES NO 1. Fully insulated cab. 2. Fully insulated headliner. 3. Fully insulated floor. Page 3 of 16

4 4. One piece molded rubber floor mat 5. Air ride cab suspension (CABMATE or Other specify ) 6. Stainless steel heated mirrors with heavy-duty hardware (Remote on both sides) + heated convex mirrors 7. Tinted glass, safety type 8. Tinted windshield, safety type. 9. Headliner, center mounted defroster circulation fan. 10. Power windows-driver & Passenger side control (O.E.M.only) 11. Dual air horns (Grover round 15 1/2" X 4" or approved equal) 12. Stainless steel dual outside grab handles. 13. AM/FM radio w/cd 14. Power port w/additional accessory port 15. Dual arm rests 16. Dome light activated by door switches 17. Dual interior sun visors. 18. Outside sun visor painted to match truck 19. Tilt / telescopic steering Padded steering wheel 21. Oversize rear cab window 22. Exterior air temperature gauge (in-cab) 23. Daylight window in passenger door 24. Proper clearance for tire chains front and rear tires, not cables ADDITIONAL SPECIFICATIONS: 1. Rust protections/undercoating 2. Heated windshield Please list price associated with addition options if applicable: GENERAL: 66,000 Lb. G.V.W.R. Tandem-Axle MAKE: MODEL: HUB RATED CAPACITY: G.V.W.R. - 66,000 Lb. minimum G.A.W.R. - Front 27,000 Lb. minimum G.A.W.R. - Front G.A.W.R. - Rear 46,000 Lb. minimum G.A.W.R. - Rear TRAILER PROVISIONS: Chassis must be set up with air brake piping assembly & fittings to rear of truck for trailer provisions with in-cab controls. Yes No Comment AXLE DIMENSIONS: Approximately " Cab to Axle Wheelbase: 220" - 226" Page 4 of 16

5 Please explain deviations Cab - to center of trunnion: In. Wheelbase: In. Turning Radius - Left: Ft. Right: Ft. BA dimension inches Cab - to center of trunnion: In. Wheelbase: In. Turning Radius - Left: Ft. Right: Ft. BA dimension inches Confirm with body mfg. for right measurements of cab to axel. FRAME: Type required: Single full length heavy duty frame (127,000 PSI) State Section Modulus: full = per rail Resistance to Bending Moment: for entire length of frame Frame size: Reinforced: One piece extended 24" in front of grill. After frame length required = 60". Provide shop drawings for any frame extension reinforcement. Y N N/A FRONT AXLE & FRONT SUSPENSION: Steering: Sheppard integral power steering w/dual steer gears. Model: Front axle: M100/M80 Single I beam, Standard track configuration with zerk fitting on the rod ends, king-pins, drag link, and ball joints. Set-back axle configuration. Capacity at ground: Front Suspension: Total capacity at ground: 27,000 Lbs. Semi elliptic springs - leaf type 27,000 Lb. Minimum Capacity lbs. Maximum available degree of wheel cut: Degrees BRAKES: Type: S-Cam brakes required front & rear. Heavy duty, full air with sufficient reserve tanks, as per FMVSS. Dust shields front/rear, inverted brake cans for asphalt dump clearance. Effective lining area: As required for G.V.W.R. & G.A.W.R. ratings. Shoe size front Chamber size inches Shoe size rear Chamber size inches Compressor to reservoir lines: Must be flexible type with flexible or rigid connections. Page 5 of 16

6 Antilock brake system: 4 Channel with air traction control & in cab switch (Prefer Bendix) Specify Brand Brake lines: Color coded nylon braided lines AIR COMPRESSOR: Shall be a Cummins 18.7 C.F.M. or approved equal CAPACITY C.F.M. COMPONENT: MAKE MODEL AUTOMATIC SLACK ADJUSTER: Meritor A.S.A. front & rear or approved equal. MAKE MODEL AIR DRYER: Bendix AD-IS EP w/heater (or approved replacement) to be located on outboard left side of frame behind the battery box. 20" ground clearance is necessary for under body scraper. EMERGENCY BRAKE: Type: Air operated with cab control emergency air supply valve and remote air reservoir EXHAUST SYSTEM: Supply an exhaust system with configuration so as not to interfere with mounting of the dump box, combination oil-fuel tank and under body scraper. System shall have a minimum of 20" ground clearance. All flex tubing must be stainless steel & 90 top of vertical stack. ELECTRICAL SYSTEM: Type: 12 volt, negative ground with eight (8) O.E.M. spare circuits/switches/wiring for cab-mounted strobes, rear box strobes, forward cab guard strobes, and additional cab-mounted plow lights. Page 6 of 16

7 The following identification O.E.M. labels should be marked on the spare switches: Plow Lights, Roof Lights, Main Strobe, Scraper Lights, Wing Strobes & Top Strobes ALTERNATOR: Heavy duty, low speed cut-in w/ transistorized voltage regulator Delco Model # 24SI or Approved equal rated at 160 Ampere minimum. Yes No Comment BATTERY BOX: O.E.M. sealed aluminum battery box with non-slip step on driver s side for batteries + additional O.E.M. step assembly on passenger side. Battery cables (00) or larger 3 - Heavy duty, threaded stud type, long life, maintenance free. S.A.E. cold cranking ampere (2075 minimum total zero degrees) 20" ground clearance is necessary for under body scraper. Optional sealed aluminum battery box (empty)/step on passenger side Add $ ELECTRICAL CIRCUIT PROTECTION: Automatic reset circuit breakers shall be used in place of fuses whenever possible. Rating - as required for adequate electrical protection. ELECTRONIC SUPPRESSION: Truck electrical systems shall be suppressed and not affect agency radio equipment. Yes No Comment ENGINE ACCESSORIES: Oil Pan: Compression Brake: Air filter: Oil filter: Fuel filter: Electrical connectors: Winter summer control: Nickle-plated to prevent premature corrosion Jacobs with in-cab three position control Dry type w/ in cab filter minder Full flow "spin-on" type, mounted on the engine block. Fuel Pro 380 w/ electric heater Weather pack silicone sealed chassis connectors required. In cab control to provide air flow from outside the truck under Page 7 of 16

8 Cooling fan: Engine heater the hood as selected by the operator. The control shall be labeled for winter or summer uses with the outside air cleaner to be located on driver s side of unit. Must be 2 speed fan clutch for frequent start/stops. Must be factory installed Yes No Comment COOLING SYSTEM: Construction: Bolt on tank construction preferred with composite construction requiring approval of the MCH. Radiator protection screen behind grille and silicone heater/coolant hoses required. Capacity: As needed for continuous low gear operations with loads of rated capacity with water/oil heat exchanger isolated from radiator for cooling of transmission. Variable speed required. Yes No Comment CONSTRUCTION: Bolt on tanks Composite CAPACITY: square inches TRANSMISSION: Allison World HD RDS Speed Wide Ratio Automatic (Torque capability to meet or exceed engine torque) MAKE: MODEL: Shift and indicator mounting: Prefer dash mounted location with push button control. Floor mounting must be approved by Marinette County. Column mountings will not be acceptable. Describe mounting location: YES NO Selector: Control w/lighted position indicator. Indicator must clearly designate all ranges. Transmission oil filter: Shall be an internal element style. Transmission instruction plate: Dash board or left door in clear view of the driver. Transmission equipped w/port for connecting ground speed control sensing equipment. Page 8 of 16

9 Automatic transmission oil cooler located so as not to interfere w/body installation Filler Tube with dip stick to be accessible from the engine compartment ecm to be relocated into the cab behind the passenger seat or other approved location PTO port available for transmission-mounted hydraulic pump REAR AXLE & REAR SUSPENSION: EATON DS461P single speed with power divider lock & lube oil pump w/ 18" ring gear Capacity at ground: 46,000 lb. minimum CAPACITY: Axle gear ratio: Axle gear ratio: To be determined following award, must meet a road speed of 65 mph, and must be approved by Marinette County. Rear suspension: Differential lock: indicator light. Gear lubricant: Hendrickson HMS w/shock absorbers. Driver controlled in both front & rear axles of tandem assembly with in-cab Synthetic gear lube required MAKE MODEL CAPACITY: FUEL TANKS & FRONT BUMPER: The fuel tank is to be sufficient for transportation only. The front bumper shall be a frame mounted bolt-on type sufficient for use during non-winter related operations and is capable of meeting FMVSS. Separately mounted DEF tank mounted on left side to be included (state size/location). SEATS & SEAT BELTS: Driver's seat: NATIONAL, high back, air suspension, cloth fabric. MAKE MODEL Page 9 of 16

10 Passenger seat: NATIONAL, high back, non-suspension. Note: Seat belts with shoulder harness and retractors shall be provided for the driver and passenger locations. All metal to metal fasteners shall meet Federal Motor Vehicle Safety Standards. Dual arm rests required on both driver & passenger seats. FRONT WHEELS & FRONT TIRES: Hub piloted wheels: Single, disc style. (8,000# & 120 psi heavy duty rim) Rim size: Wheel seals: Front tires: Size: 12:00-10 hole hub (Inset Rim) National Federal-Mogul Teflon oil bath seals Tubeless radial, over the road tire. Michelin XZY or Bridgestone M844F TL 425 / 65 R 22.5 Load range: L (20 ply) or approved equal by Marinette Co. TIRE: BRAND: TREAD: SIZE: REAR WHEELS & REAR TIRES: Hub piloted wheels: Dual, disc style (8,000# & 120 psi heavy duty rim) Rim size: 8:25-10 hole hub. Dual spacing for use of tire chains. Rear Tires: Size: Load range: Tubeless, radial non-directional, mud and snow drive tire. Continental HDL 11 R22.5 or approved equal by Marinette Co. H (16 ply) or equal. TIRE: BRAND: TREAD: SIZE: FRONT FENDERS & HOOD ASSEMBLY: Page 10 of 16

11 Construction: Fiberglass MATERIAL: Type: Manufacturer's standard assembly. Forward tilting with stationary grille. Tilting hood shall be provided for routine maintenance without removal of the hood assembly or the snowplow push frame. Must have proper clearance for tire chains not cables. DESCRIBE HOOD ACCESS: FENDER FLARES Fender flares of size recommended by the Manufacturer for chassis and completed truck. INNER FENDER MOTOR SPLASH GUARDS: Splash guards of size and type by Manufacturer for chassis and completed truck. To be hood mounted with sufficient bolt-on bracing for the heavy duty application and proper clearance for tire chains. COMPONENT: MAKE: MODEL: REAR VIEW MIRRORS: Type: Dual, electrically heated (control from in Cab), outside rear vision. Glass mounted in stainless steel frame, rubber or plastic not acceptable. Mounted with heavy duty hardware. Remote control on both sides + heated convex mirrors. Size: Approximately 16" X 7" w / 8" heated convex mirror (both sides) bottom mount. INSTRUMENT AND WARNING SYSTEM: The following instrument and warning systems shall be furnished. 1. Speedometer 2. Odometer 3. Tachometer 4. Fuel gauge 5. Hour meter: Prefer oil pressure activated or may be electric model activated by engine rpm. Type: 6. Engine coolant temperature gauge with high recommended temperature warning light & buzzer 7. Air pressure gauge with warning low-pressure warning light and buzzer. 8. Engine oil pressure gauge with low-pressure warning light and buzzer. 9. Transmission temperature gauge. 10. Manifold pressure gauge. 11. Engine air filter restriction gauge-in-dash mounted filter minder. Page 11 of 16

12 12. Voltmeter 13. Interior / exterior air temperature gauge 14. Air brake application pressure gauge 15. DEF gauge Yes No If No, Describe HEATER & DEFROSTER & AIR CONDITIONER: Heavy duty, hot water, fresh air, type with all controls for effective heating and/or defrosting under cold weather conditions with removable intake filter for winter use. Supply O.E.M. air conditioning unit. Yes No BTU s WINDSHIELD WIPERS: Type: Dual, heavy duty, electric two-speed windshield wiper with intermittent speed control and electric washer. Blades: Rubber covered components similar to TRICO AR-11-1 blades. YES NO CONTROL LOCATION STANDARD LIGHTS: Headlights with high/low beams: Type: Sealed beam, 2 or 4 elements. Halogen Location: Standard production location. Lens color: Clear Control: Combination light control switch with turn signal mounted dimmer switch. YES NO FRONT TURN SIGNAL AND PARKING LIGHTS: Location: Front fender Lens color: Front amber Parking light control: Combination light control switch. Turn signal control: Turn signal control switch and 4-way hazard warning switch. Yes No Comments CAB CLEARANCE LIGHTS: Location: Outer front edge of cab top. Lens color: Amber Control: Combination light control switch Page 12 of 16

13 Yes No Comments REFLECTORS: As required by Wisconsin state law. Yes No Comments 4 - WAY HAZARD SWITCH: Type: As required to operate all turn signal lights simultaneously in a flashing mode, with heavy duty flasher. Yes No Comments PAINT: Color: Bright Orange, comply w/ Dupont Imron 498H or Sikkens Navo 323 Areas: Cab shall be painted orange. The dealer shall provide all necessary information regarding lot # & paint codes to the body dealer for matching. Frame and running gear shall be painted manufacturer's black. Yes No Comments PAINT SPEC. # STANDARD MANUFACTURER'S WARRANTY: Coverage: All defective parts and workmanship from delivery date & acceptance from the body dealer. Warranty on Chassis will start when we receive completed truck from body builder. Warranty Service: All defects shall be promptly corrected on-site at no cost to the Marinette County Highway Department. STATE STANDARD MANUFACTURER S WARRANTY STATE ADDITIONAL WARRANTIES, INCLUDE ADDITIONAL COSTS LITERATURE: Page 13 of 16

14 Proposer shall submit two sets of literature describing the make and model of the truck that they propose to furnish. Yes No Comments Proposer shall give access to all online parts (for life of truck) and engine diagnosis programs for a minimum of 1 year at no cost. SUMMARY SHEET: A summary sheet of the manufactures truck components is to be supplied with the quote. SAFETY COMPONENTS: The truck shall be furnished complete with all safety components that are required by the current Federal Safety Standards for the size of truck proposed to be furnished. Yes No Comments NEW TRUCK INSPECTION: It will be the responsibility of the successful proposer to deliver the units F.O.B. Body Dealer. Before the trucks are delivered to the Dealer, the vendor shall make a complete inspection of the units to ensure operation of the trucks and that all parts are properly lubricated. The vendor shall correct any defects before delivery. Yes No Comments F.O.B. BODY LOCATIONS: Monroe Truck Equipment, DePere Olson Trailer & Body, Green Bay Casper Truck Equipment, Little Chute Truck Equipment, Green Bay OPERATOR'S BOOKS: The successful proposer shall furnish at least one additional operator's instruction and maintenance manual to the destination to which units are delivered, in addition to the books which shall be in each truck. EXTRA KEYS: The dealer is to supply 4 extra keys for doors and ignition for the truck with no extra cost to Marinette County Highway Department. SERVICE MANUALS: Successful proposers shall have their District Manager or Fleet Service Manager contact Marinette County about warranty, service manuals, and service bulletins prior to vehicle delivery to the destinations. Two (2) sets of each manual or a adigital copy of the manuals listed below is required with no charge to Marinette County. Parts Manual - Custom illustrated * Service Manual * Line Sheet Page 14 of 16

15 Service Bulletin Updates as required. * Includes Engine, Transmission, and ABS brake system. YES NO Manuals: Operators manual shall accompany each unit at time of receipt. The Marinette County Highway Department reserves the right to accept or reject any and all quotes, to waive any irregularities in quotes and to make the award of the quote in the best interest of the county. Special consideration will be given to a proposer based on past performance with regard to ability to stock & supply parts and components. The speed in which parts & components are received from suppliers, location of the facility to ship and deliver is very important. DELIVERY: It will be the responsibility of the successful truck vendor to guarantee delivery of the chassis within the quoted time to the body dealer. The chassis proposer is not responsible for delays created by the body installation dealer. The chassis dealer is responsible for prompt F.O.B. delivery to the Marinette County Highway Department in Peshtigo upon completion of the body package installation. TRAINING: The successful proposer shall provide reasonably available literature/videos for the training of mechanics and operators. Yes No Comments PRICING: Year Make Model Price $ Each TRADE-IN UNITS The units listed below may be used as trade in with the purchase of the (2) 2018 Tri-Axle Cab and Chassis. # International X2 Truck with dump box with snow removal equipment, mileage not known. $ # International 2674 Truck with dump box with snow removal equipment, mileage not known. $ Page 15 of 16

16 Proposed Tri-Axles Year Make Model Price Less Trade-In Total Cost $ $ $ The Marinette County Highway Department reserves the right to accept bids from the public for comparison of trade in unit quote from successful bidder prior to anticipated delivery date of new vehicles. I have full authority to make such statements and to submit this quote as the duly recognized representative of the Proposer. Signature of Duly Authorized Individual Date Printed Name: Title: Business Name: Address: Phone Number: Address: Page 16 of 16