Rebuilding the HE-120 Redrive
|
|
- Natalie Robertson
- 5 years ago
- Views:
Transcription
1 Rebuilding the HE-120 Redrive Rick Cavallaro Disclaimer: I am NOT an expert mechanic. If something looks or sounds wrong in these directions, it probably is. I d be happy to receive any tips or feedback on how to improve this ( wired.cav@gmail.com ) Special tools needed: Circlip pliers Blind bearing puller ( See Fig. 1) Spanner and pinion holder (homemade see Fig. 2) Arbor press (bench vice or drill press may suffice) Figure 1: Blind bearing puller - $40 from Harbor Freight Tools
2 Figure 2: Homemade spanner and pinion holding tool.
3 Bearings and seals Output shaft bearing: Bearing: 6003 C3 I.D. 17mm; O.D. 35mm; Width: 10mm - open - no shields Available from: Nachi Bearing Open C3 Japan 17x35x10 Ball Bearings Code: Kit9805 Price: $5.88 Output shaft pilot bearing: Bearing: 6002 C3 I.D. 15mm; O.D. 32mm; Width: 9mm - open - no shields Available from: Nachi Bearing Open C3 Japan 15x32x9 Ball Bearings Code: Kit9804 Price: $4.88 Pinion gear bearing: Bearing: 6003 RSR I.D. 17mm; O.D. 35mm; Width: 10mm Available from: NSE Nachi Bearing 17x35x10 Sealed C3 Japan Ball Bearings Code: Kit9678 Price: $7.88 Pinion gear pilot bearing: Bearing: 6000 C3 I.D. 10mm; O.D. 26mm; Width: 8mm - open - no shields Available from: Nachi Bearing Open C3 Japan 10x26x8 Ball Bearings Code: Kit9802 Price: $4.88 Output shaft seal: Sorry I didn t note the specs for these. Pinion shaft seal: These either
4 Disassembly of the HE-120 Redrive Remove the three nyloc nuts that mount theredrive to the engine. You may want to leave the propeller on at this stage as it will make it easy to keep the output shaft from turning when removing the clutch bell. Alternatively, you can use the homemade pinion holder (figure 2) to keep the pinion from turning at that step. Remove the unit from the engine. Using the homemade spanner to remove the clutch bell (Figure 3). The clutch bell unthreads from the pinion with a counter-clockwise torque.
5 Figure 3: Removing the clutch bell using the homemade tools. Once the clutch bell has been removed you can remove the prop (if you haven t done so already). Remove the bolt that threads into the output shaft and holds the prop mounting plate in place. Remove the prop mounting plate. Mine was on there TIGHT. Using a torch to heat the aluminum mounting plate will make it come off much more easily. It s probably best to assume that heat will destroy bearings and oil seals but all should be replaced in any case. Loosen the six bolts that hold the two halves of the case together. Back them out a quarter inch or so. Holding the case from the output shaft side, use a rubber mallet to tap on these bolts to separate the two halves. The two halves are being held together by the pinion and output shafts that are seated in the bearings. Mine did not come apart easily. You can see some pry marks on my case halves because I tried every way of separating the two halves. If anyone has ideas on how better to separate the two halves I d love to hear it ( wired.cav@gmail.com ) Press the output shaft out of the bearing that s seated in the front half of the case and remove the output gear. Remove the output shaft oils seal. This should push out without too much trouble from the bearing side. I used a small screwdriver to do this. Heat the case with a torch and remove the output shaft bearing. It should come out reasonably easily with heat. Alternatively you could most likely press it out with an arbor press. Remove the pilot bearing that supports the opposite side of the output gear. I tried everything here as well. The ONLY thing that worked for me (and it worked like a dream) was a blind bearing puller (Figure 1). You can get one of these for $40 from Harbor Freight Tools and it s worth every cent ( )
6 From the clutch bell side, press the pinion gear out of the bearing that supports it. This is best done with an arbor press. I did it on my drill press. From the pinion gear side push out the oil seal toward the clutch bell side. Using circlip pliers remove the circlip on the clutch bell side. This holds the pinion bearing in place (figure 4). Figure 4: Circlip retainer holds the pinion shaft bearing in place Press the pinion bearing out toward the clutch bell side. Again, and arbor press is probably the right tool (and again I used my drill press).
7 Using the blind bearing puller (figure 1), remove the pinion gear pilot bearing from the other half of the case. I found it best to mount the case to a large piece of wood when using the bearing puller. Re-Assembly of the HE-120 Redrive Press the new bearing onto the shaft of the pinion gear (Fig 5). I did this with a standard bench vise. You should really use an arbor press. Note: I used a socket between the vise jaw and the inner bearing race, and a piece of plastic between the pinion shaft and the opposite jaw. The socket insures that no force is taken by the balls between the two races. We want to put pressure on the inner race to press the inner race onto the pinion shaft. We don t care about the old bearings, but we want to treat the new ones right when installing. I also chose not to use any heat when installing the new bearings. I didn t want to cook the grease in the bearings or melt the oil seals. Figure 5: Pressing the pinion gear into the new bearing
8 Go slowly and make sure the bearing is going on straight. If you see a slight misalignment, correct it right away. Don t force the bearing on with any misalignment. Press the bearing and pinion into the case (figures 6 and 7). I put the assembly on a piece of wood directly over a hole that would allow the pinion to extend downward as the bearing was set. Figure 6: Pinion and new bearing partially pressed into the case To set this bearing I used a larger socket to ensure that all the force is placed on the outer race as that race is pressed into the case (figure 7). In this case I tapped it in with a hammer, again making sure to keep the bearing aligned at all times. Again, you would probably be better off with an arbor press.
9 Figure 7: Using socket to insure force is applied to outer race only Once the bearing is seated well in the case, replace the circlip retainer using a pair of circlip pliers (figure 4). Be careful to insure the circlip is well seated in the groove all way around (figure 8).
10 Figure 8: Fully seated circlip retaining pinion shaft bearing
11 Figure 9: Inserting output shaft pilot bearing Turn the case over and insert the pilot bearing for the output shaft (figure 9 and 10). Again, I used a large socket to engage the outer race only and again tapped it in with a hammer.
12 Figure 10: Pilot bearing seated in case
13 Figure 11: Clutch bell oil seal re-installed Re-install the bearing seal where the clutch bell will go. I put a film of oil on the inner and outer seal surfaces before installing the seal by hand. It just seemed like a good idea. Thread the clutch bell back on the pinion shaft (figure 12 & 13). Clockwise to tighten.
14 Figure 12: Re-installing the clutch bell
15 Figure 13: Clutch bell threaded onto pinion shaft finger tight Insert the output gear into its bearing and then use the homemade tools to prevent the pinion from turning while you turn the clutch bell clockwise to tighten it firmly onto the pinion shaft (figure 14).
16 Figure 14: Tightening (or loosening) the clutch bell using home made tools Figure 14 shows the homemade pinion holding tool. Note, this piece of hardwood has two holes to accommodate both the main gear and pinion gear shafts. It also has 6 bolts that engage the main gear to keep it from turning while the clutch bell is being tightened with the homemade spanner. Press the output shaft bearing into the case (figures 15 & 16). In this case I used a socket to insure the force was carried only by the outer race, and pressed it in with my bench vice. As always, I m sure an arbor press is a better choice.
17 Figure 15: Setting the output shaft gear in place to be pressed in.
18 Figure 16: Pressing the output shaft bearing into the case Re-seat the main gear in its pilot bearing in the case so that it properly engages the pinion gear. Press it fully into the bearing with an arbor press. Put the rubber O-ring gasket in place before putting the two halves of the case back together. Place the front half of the case over the output shaft. Line it up and press it on by hand as far as possible. Put a socket over the output shaft so it presses on the inner race of the bearing. Press the case on over the output shaft using an arbor press (putting the force on the socket). Put the six screws back in that hold the two halves of the case together. The two longer screws go to either side of the shaft. The four in the corners are slightly shorter. Put the new oil seal over the output shaft and seat it in the case. This can be done fairly easily by hand.
19 Insert the woodruff key into the output shaft and then carefully place the prop mounting plate on the shaft so that it aligns with the key. Press the prop mounting plate onto the shaft until it s fully seated. I chose not to heat the mounting plate because I didn t want to damage the oil seal. It doesn t slide on easily. Alignment is everything. Once it s clearly engaged over the key, I use the bolt that holds it in place to pull it down until it seats. I figured this has the advantage that it places no axial force on the bearings. To keep the shaft from turning while I tighten the screw, I place a screwdriver through one of the holes in the case and one of the holes in the clutch bell. I did this without the lock-washer, and then backed the screw out, added Loctite and put it back in with the lock-washer in place. With both the top vent and side plug removed, put 55 cc s of gear oil in the case. This should fill the case right up to the side plug hole. It should be easy enough to check the oil level and quality every so often by removing both the top vent and side plug, and tipping the whole unit a bit to one side to get a bit of oil on your finger. If you have to tip the unit more than a few degrees to get a bit of oil out, your oil is low.
DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
More informationFD Transmission Rebuild: Parts Inspection
FD Transmission Rebuild: Parts Inspection Now that everything is disassembled, cleaned, and bagged in labeled Zip-Locs, it s time to decide what to replace. Warning: I m not a transmission specialist I
More informationThough Indian s 111-cubic-inch engine delivers a
TECH by Chris Maida Andrews Indian 111 Camshafts Part I: Removing the cams from the camshaft compartment Tools Needed Red Loctite Clean rags 6mm Allen 5/64" Allen 3/32" punch External circlip pliers Needlenose
More informationMaintenance Information
16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationImproving the gearshift feel in an SW20.
Improving the gearshift feel in an SW20. Part one In 3 parts. The SW20 gearshift can be often be greatly improved by eliminating play in the shift linkages, and this article covers three areas that need
More informationNOTE: Visit our website at for video repair procedures, under the Tools section.
Repair Instructions Hypro Repair Tools: Tool Box No. 3010-0168 1/4" Allen Wrench No. 3020-0008 Support Bars (2) No. 3010-0064 Port Brush No. 3010-0066 1/16" Allen Wrench No. 3020-0009 Brush Holder No.
More informationMaintenance Instructions
General Note These instructions contain information common to more than one model of Bevel Gear Drive. To simplify reading, similar models have been grouped as follows: GROUP 1 Models 11, 0, 1,, (illustrated),,
More informationCALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL
CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationTransmission Overhaul Procedures-Bench Service
How to Install the Auxiliary Countershaft Assembly Special Instructions To make auxiliary section assembly easier, you can make an auxiliary section fixture out of a 2" x 12" piece of wood. 3' 1' 3" 4.56"
More informationMaintenance Information
45528270 Edition 1 June 2007 Barring Motor T480 Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this Barring Motor.
More informationMaintenance Information
16575243 Edition 2 October 2013 Air Screwdrivers 1R Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationSachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport
Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,
More informationMaintenance Information
80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing
More informationTORCH MOUNTAIN REAR HUB SERVICE
Industry Nine products are designed to keep you in the saddle and out of the service queue. Regular service and maintenance is simple and can be performed with basic tools readily available to the home
More informationTransmission Overhaul Procedures-Bench Service
How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole
More informationMaintenance Information
Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard
More informationTorqueflite Manual/Automatic Valve Body
TCI 122400 Torqueflite Manual/Automatic Valve Body This valve body can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts
More informationMaintenance Information
80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the
More informationMaintenance Information
04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,
More information1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
More informationAmateur Radio Station WFØGM Repairing a Yaesu G-1000DXA Rotor
WFØGM Home http://wf0gm.fpage.com/index.htm Amateur Radio Station WFØGM Repairing a Yaesu G-1000DXA Rotor (Part 1 of 2) The following is my experience with a faulty Yaesu G-1000DXA Rotor, and how I repaired
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationReplacing the hub oil seal.
Replacing the hub oil seal. The most common reason for hub oil seal failure is a blocked axle breather, so check this first before you start. Remove the brass bell-shaped fitting on the top of the axle,
More informationHKS 700E. Service Manual June Ver. 2.04
HKS 700E Service Manual 009 June Ver..04 HKS CO.,LTD 78 KITAYAMA FUJINOMIYA SHIZUOKA JAPAN 48-09 TEL +8(0)544-54-78 FAX +8(0)544-54-40 hks_aviation@hks-power.co.jp http://www.hks-power.co.jp/hks_aviation/
More informationMaintenance Information
16606022 Edition 3 May 2014 Air Drill 728 Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationMaintenance Information
16584062 Edition 3 December 2013 High Torque Reversible Angle Screwdrivers and Angle Wrenches QA1L High Torque Series Maintenance Information Save These Instructions Product Safety Information WARNING
More informationInstalling Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More informationMaintenance Information
16572554 Edition 2 May 2014 Air Drill 44SMA, 44SMA-EU Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More informationRebuilding the Power Steering Pump for a 2007 Honda Accord 4CYL
Rebuilding the Power Steering Pump for a 2007 Honda Accord 4CYL Disclaimer: I have benefited greatly from others who have taken the time to post auto repair videos/tutorials online. To try and return the
More informationC3 Syncro Drive Proclimb 1100 Installation Instructions
Revision 4 Nov 8-2013 201A Old Town Road, Sicamous, BC. V0E 2V4 Ph 250-833 3538 Fax 888-716 5903 www.c3powersports.com Thank you for purchasing a ProClimb M, ProCross F & XF SyncroDrive Note: This modification
More informationMaintenance Information
16575219 Edition 4 October 2013 Air Screwdrivers QP1P, QP1S and QP1T Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,
More informationThere is hence three things you can do - add oil, adjust the temp that the clutch begins to engage, or do both.
As most of you may be aware, I have been doing a lot of research lately on our cooling system in the 80's including the fact that we have a dead spot on the OEM temp gauge which prompted me to not rely
More informationON VEHICLE REPAIR Valve Body
AT28 AUTOMATIC TRANSMISSION ONVEHICLE REPAIR Valve Body REMOVAL OF VALVE BODY 1. CLEAN TRANSMISSION EXTERIOR To prevent contamination, clean the exterior of the trans mission. 2. DRAIN TRANSMISSION FLUID
More informationSteering Gearbox Disassembly
Steering Gearbox Disassembly Steering Rack Disassembly 5. Unbend the lock washer. Before disassembling the gearbox, wash it off with solvent and a brush. Do not dip seals and O-rings in solvent. 1. Remove
More informationMaintenance Information
16596199 Edition 2 May 2014 Air Drill 33 Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More information2001 Dodge RAM 3500 PICKUP
1 of 76 9/14/2012 7:02 PM 2001 Dodge RAM 3500 PICKUP Submodel: Engine Type: L6 Liters: 5.9 Fuel Delivery: FI Fuel: DIESEL Subarticles MANUAL- NV3500 - DISASSEMBLY MANUAL- NV3500 - DISASSEMBLY MANUAL -
More information95-97 Toyota Tercel & Paseo Short Throw Shifter Installation Manual
95-97 Toyota Tercel & 92-97 Paseo Short Throw Shifter Installation Manual Estimated Installation Time: 40-60 Minutes Tools Required: -Philips head screwdriver and flat head screwdriver -Bench vise -10mm,
More informationRebuilding the Alternator for a 2007 Honda Accord 4CYL. Honda CYL Alternator (Denso)
Rebuilding the Alternator for a 2007 Honda Accord 4CYL Honda 2007 4CYL Alternator (Denso) The OEM brushes and bearings for this alternator are available for purchase online. On my vehicle with ~240k miles,
More informationMaintenance Information
45761848 Edition 3 February 2014 Air Die Grinder AC4A, SC4A and XC4A Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. Description BHR202 Cordless Combination Hammer CONCEPT AND MAIN APPLICATIONS The subject model features 18V Li-ion Battery and 3 mode selection for ensuring an operator
More informationSlide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.
Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings
More informationA/C COMPRESSOR SERVICING Article Text 1991 Saab 9000 For Copyright 1997 Mitchell International Friday, October 15, :22PM
Article Text ARTICLE BEGINNING 1991 GENERAL SERVICING Compressor Service * PLEASE READ THIS FIRST * CAUTION: When discharging air conditioning system, use only approved refrigerant recovery/recycling equipment.
More informationE31 Repair Procedure Replace Front Wheel Hub/Bearing Assembly
E31 Repair Procedure 31-21 Replace Front Wheel Hub/Bearing Assembly Disclaimer This repair procedure is provided as is and is not authoritative with respect to any BMW repair operation. Mark F. Fling is
More informationGenesis Double Adjustable Shock Assembly and Repair
Genesis Double Adjustable Shock Assembly and Repair General Operating Description The Genesis Adjustable Shock is adjusted by moving one or both of two bypassing sliding valves. These valves slide longitudinally
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More informationDrive shaft left-hand side, replace
"VCC126387 EN 20090226" file://c:\info\vv132007\ie\en\30\vcc126387.htm Page 1 of 13 Drive shaft lefthand side, replace Special tools: 9995681 Removal Removing the drive shaft nut the hub cap the drive
More informationInstallation Instructions
Instructions Created by an: 86-95 Suzuki Samurai Samurai Complete Transmission Rebuild Kit with Synchronizers (SKU# STM-RP) Installation Instructions Part I Notice: If there are any parts you need that
More informationTorqueflite Trans-Scat Kit
TCI 220000 Torqueflite Trans-Scat Kit This kit can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts and procedures. Work
More informationFOX Racing Shox Bypass Technical Manual.
FOX Racing Shox Bypass Technical Manual. The following technical manual will be using a 2.5 dia. shock with three tubes for descriptions and illustrations. Your shock may differ in the number of tubes,
More informationSPECIAL TOOLS. Core Drilling Machines SERVICE MANUAL. Page 1
SPECIAL TOOLS Core Drilling Machines Page 1 SERVICE MANUAL Service Manual Necessary Tools for machine assembly BEAST by BBTEC Core Drilling Machines 1 Soft Hammer (preferred plastic head) Art. 6.512.096
More informationMaintenance Information
16573370 Edition 2 February 2014 Air Grinder 99V Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationMaintenance Information
Form 04584058 Edition 1 November 2004 Air Impactool 2141P and 2141PSP Maintenance Information Save These Instructions Disassembly General Instructions 1. Do not disassemble the tool any further than necessary
More information1964 1/2-70 Mustang Torque Arm Rear Suspension Installation Instructions
1964 1/2-70 Mustang Torque Arm Rear Suspension Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Version 2 (c) 2008 Total Cost Involved Engineering, Inc. All Rights Reserved. Page 1 of
More informationREAR DRIVE SHAFT (3S GTE ENGINE)
SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationDRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I
DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment
More informationRotax Sprag Replacement
Rotax Sprag Replacement This is intended as a full walk through on a Sprag replacement on a Electric start Rotax engine These instructions were made from a sprag replacement on an MT 350 Tools List Non
More informationInstallation Instructions
Instructions Created by an: Inchworm Gear Clockable Toyota Dual Transfer Case Adapter Kit, 21 or 23 Spline SKU# TCASE-IW-300-000 Installation Instructions CAUTION: Safety glasses should be worn at all
More informationInstallation Vertical Pump: Installation 'CM' and 'CDM' Style: Operation:
Installation Vertical Pump: Gusher vertical end suction pumps with integral shaft is easily installed and put into service. With the one piece shaft design there is no couplings to align, no shims or no
More informationSUSPENSION - FRONT Infiniti G20 DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Front G20
SUSPENSION - FRONT 1992 Infiniti G20 1991-92 SUSPENSION Front G20 DESCRIPTION G20 uses a 4-wheel independent multi-link suspension system. Transverse links are connected to bottom of steering knuckle.
More informationGearbox Assembly 101. Introduction. Before Beginning. By Mark Schutzer 4/13/06
Gearbox Assembly 101 By Mark Schutzer 4/13/06 Introduction If you are planning to re-motor an old brass locomotive you may want to upgrade to a new gearbox at the same time. The early 60 s and 70 s gearboxes
More informationTECHNICAL SERVICE MANUAL
TECHNICAL SERVICE MANUAL VIKING HELICAL GEAR REDUCERS "A", "B", AND "C" SIZES SECTION TSM 610 PAGE 1 OF 9 ISSUE E CONTENTS Special Information 2 Lubrication 2 Installation 3 Operation 3 Disassembly 3 Assembly
More information1. General Description
1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final
More informationTROUBLESHOOTING. Avoid getting grease and oil on the drive belt and pulley faces.
8 KICK STARTER/DRIVE PULLEY/ SERVICE INFORMATION... 8-2 TROUBLESHOOTING... 8-2 LEFT CRANKCASE COVER... 8-3 DRIVE PULLEY... 8-3... 8-7 KICK STARTER... 8-14 0 1 SERVICE INFORMATION GENERAL INSTRUCTIONS Avoid
More informationFluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL
Fluid-O-Tech PUMP TECHNOLOGY AT ITS BEST WWW.FLUID-O-TECH.COM Office: 161 Atwater St., Plantsville, CT 06479 Phone: (860) 276-9270 Fax: (860) 620-0193 ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL 08/09 Ed.,
More informationINTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco
Rockcrawler Steering Shop Manual page1 The following is from the Ford 1978 Truck Shop Manual, Volume 1 Chassis. It is provided here as a courtesy to classic Ford owners who would like to perform their
More informationFull Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra)
Full Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra) Tools Required: Jack and jack stands (Or a lift) Metric sockets 8,12,15,18,21mm and a 12pt 12mm socket for driveshaft bolts T40 torx bit
More informationENG-14, Balance Shaft Oil Seal Replacement
ENG-14, Balance Shaft Oil Seal Replacement Introduction The following procedure will provide instructions for replacing the balance shaft seals on a 944. It will also provide instructions for resealing
More informationBOSCH PERFORMANCE LINE BEARING CHANGE Outline Instructions
BOSCH PERFORMANCE LINE BEARING CHANGE Outline Instructions Saturday, 30 June 2018 22 COMPONENTS 1. Crank shaft 2. Reduction gears 3. Idler gear 4. Security nut for torque sensor 5. Main motor drive gear
More informationDisassembly Instructions hp. Dynafile II Models: 40352, 40353
Disassembly Instructions - 0.4 hp. Dynafile II Models: 40352, 40353 Important: Use these instructions along with the tool parts page or manual. Notice: Shut off the air supply and depress throttle lever
More informationShock absorber for Automotive TTX36 P/ IL. Workshop Manual
TTX6P TTX6IL Shock absorber for Automotive TTX6 P/ IL Workshop Manual Safety precautions General Warnings Note! The shock absorber/front fork/steering damper is an important part of the vehicle and will
More informationPOWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly
POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly DISASSEMBLY: 1. Remove pump from car and allow to drain. 2. Remove pulley from front of pump. This requires
More informationINGERSOLL -RAND. A WARNING AIR MOTORS OPERATION AND MAINTENANCE MANUAL
03523545 Form P5815 Edition 13 June, 1998 OPERATION AND MAINTENANCE MANUAL FOR MODELS 4800D, 4800K, 4800M, 4800N, 4800P, 4800Q, 4800S AND 4800U NONREVERSIBLE AND MODELS 4840D, 4840K, 4840M, 4840N, 4840P,
More informationBBK Caster/Camber Kit (87-93)
BBK Caster/Camber Kit (87-93) Materials in the box 2 Polished Aluminum Plates 2 Steel Strut Mounts 4 Polyurethane Bushings 2 Stud Plates 2 Bushing Sleeves 2 5/8 Flat Washers 2 5/16 Allen Head Bolts 4 5/16
More informationFOR FUTURE REFERENCE SERIES 93HPS
Hypro Series 93HPS Hydraulically Driven Wetseal Multistage Pumps Repair Manual KEEP FOR FUTURE REFERENCE Form L-1578R Rev. A SERIES 93HPS Hydraulically Driven Stainless Steel Multistage Centrifugal Pumps
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationMaintenance Information
16573347 Edition 2 February 2014 Air Grinder Series 88H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationTCI Trans-Scat
Page 1 of 5 Return to Instruction Sheet index TCI 400000 Trans-Scat Turbo Hydramatic 400-1965-Up This kit will allow you to re-program your transmission valve body. This kit will give you firm positive
More informationMaintenance Information
16575128 Edition 2 May 2014 Air Grinder, Sander or Polisher 77A Series Maintenance Information Save These Instructions Product Safety Information Failure to observe the following warnings, and to avoid
More informationINSTALLATION INSTRUCTIONS. FD3S RX7 Manual Rack Conversion
INSTALLATION INSTRUCTIONS FD3S RX7 Manual Rack Conversion 1 Removal of Stock Rack 1.1 With your steering wheel centered, remove the pinch bolt from the factory intermediate shaft lower knuckle. If you
More informationFerrari 355 Challenge Grill Installation
Ferrari 355 Challenge Grill Installation By: Dave Lelonek (Dave Rocks) August 12, 2014 Created based on model year 1998 (355 F1 GTS), other model years may apply. Disclaimer: This document was created
More informationINSTRUCTIONS FOR OVERHAUL OF RAMEY RE SERIES WINCH
INSTRUCTIONS FOR OVERHAUL OF RAMEY RE 12000 SERIES WINCH DISASSEMBLY 1. Drain oil from gear housing by removing plug # from bottom of gear housing. Remove relief fitting # and reducer # from top of gear
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationGftOUP 4 PARKING BHAKE
PARKING BRAKE 4-1 GftOUP 4 PARKING BHAKE CONTENTS Page Data and Specifications... 1 External Contracting Type Parking Brake...... 2 Parking Brake Band Lining 3 Parking Brake Internal Expanding Type 5 Parking
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Model No. Description DP4010, DP4011 2-Speed Drill 13mm (1/2") L PRODUCT P 1/ 8 CONCEPT AND MAIN APPLICATIONS Models DP4010 and DP4011 have been developed as 13mm (1/2") Drill for
More informationDisassembly Instructions hp. Mini-Dynafile II
Disassembly Instructions - 0.4 hp. Mini-Dynafile II Important: Use these instructions along with the tool parts page or manual. Notice: Shut off the air supply and depress throttle lever to deplete the
More informationCoro-Vane Maintenance CP471. and Disassembly
Coro-Vane Maintenance CP471 and Disassembly CoroVane Pumps Pumps all have discharge and suction pressure openings. The following slides depict a 1021, but all standard pumps are repaired the same. Grease
More informationINSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS:
INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS: G-H, G-HL, G-K, G-KK, G-L, G-LQ, G-LL, GLS, G-Q, G-QS 1 Contents Maintenance Thrust bearing adjustment
More informationInstallation Instructions
Instructions Created by an: Inchworm Tacoma Dual Case Adapter Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools
More informationRear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)
Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black
More informationOPERATION AND MAINTENANCE MANUAL for SERIES 7 AIR DRILLS
03530896 OPERATION AND MAINTENANCE MANUAL for SERIES 7 AIR DRILLS Form P6532 Edition 10 February, 1994 TPD1388 IMPORTANT SAFETY INFORMATION ENCLOSED. READ THIS MANUAL BEFORE OPERATING TOOL. FAILURE TO
More informationCONTENTS. VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA USA SECTION TSM 710.1
TECHNICAL SERVICE MANUAL industrial heavy duty motor speed pumps SERIES 4076 AND 4176 SIZES hle, ate and ale SECTION TSM 710.1 PAGE 1 of 8 ISSUE B CONTENTS Introduction....................... 1 Safety
More informationHow to install the Barnett clutch and the stronger Oil Pump Drive Gear
How to install the Barnett clutch and the stronger Oil Pump Drive Gear Written by WildFred I m from Germany so please excuse my English and the spelling. The following procedure is a combination of the
More informationRekluse Motor Sports. The ProStart Clutch. H-D Sportster (2004 +)
Rekluse Motor Sports The ProStart Clutch H-D Sportster (2004 +) Installation Guide Copyright 2006 Rekluse Motor Sports ProStart Revision 1.000 RMS687 H-D Sportster 195-687 Manual Revision: 111308 Rekluse
More informationIPSCO STS (Short Throw Shifter) Installation Instructions (GEN II) Dodge Viper WARNING
WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly assumes all risks associated with any such modification. DISCLAIMER OF WARRANTY
More information3M Overhaul Service Kit
SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 5 in. (127 mm) and 6 in. (150 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20347, 3M Overhaul Service Kit, contains all the replacement parts
More informationREPAIR PROCEDURES MANUAL
REPAIR PROCEDURES MANUAL PVX Series Vane Pumps A Design Series Step-by-Step Guide to Troubleshooting and Repairing PVX Series Vane Pumps Introduction Thank you for choosing Continental Hydraulics PVX Vane
More information