Installation Instructions
|
|
- Emory George
- 5 years ago
- Views:
Transcription
1 L-PB L-PW Installation Instructions Component Checklist Arm Assembly (with pre-assembled Desk Clamp) Hardware Desk Single Rotation Limiter (x1) (x1) 2mm Allen (x1) Cable Clip (x4) Spacer Bush (x4) Fasteners (x2) Washer (x1) Head Cap (x1) Tools Required: Cover Plate Screw (x1) Washer (x3) Phillips Head Screwdriver Power Drill 8mm ( 5 /16 ) Drill Bit Base Plate Display Mounting Screws: M4 x 12mm (x4) M4 x 16mm (x4) M5 x 12mm (x4) M5 x 16mm (x4) IMPORTANT INFORMATION! IMPORTANT - Install Levitate Single Monitor Arm as per Installation Instructions.! This product supports a maximum load of 9kg (19.75lbs).! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.! The manufacturer accepts no responsibility for incorrect installation. Step 1. Check Components Check you have received all parts against the Component Checklist and Hardware above. Step 2. Base Setup (OPTIONAL) The Base can be setup for either Desk Clamp or installations. The Base can also be setup to allow infinite 360 rotation, or limited to 180 rotation. This provides 4 Base setup configurations (see options A,B,C,D listed below): A. Desk Clamp/360 > Default setup, skip to Step 3A [PTO]. C. /360 > Install Base Plate only. B. Desk Clamp/180 > Install Rotation Limiter and Desk Clamp. D. /180 > Install Rotation Limiter and Base Plate. 1 Start by removing the Desk Clamp using the supplied. 2 DESK CLAMP (for Base configuration B) For Desk Clamp/180 configuration, insert the Rotation Pin and re-install the Desk Clamp. 2 BOLT THROUGH (for Base configurations C and D) For Bolt-Through configurations install the Base Plate instead of the Desk Clamp. REMOVE Desk Clamp TIP: If the Desk Clamp is tight in the Base, tap lightly with the palm of your hand to release. TIGHTEN FIRMLY Rotation Limiter Desk Clamp OR Base Plate Rotation Limiter (configuration D only, 180 ) Tip: When inserting the Rotation Limiter, the Base and the Lower Arm must be aligned as shown above.
2 Step 3. Install Arm to Work Surface Choose from either Desk Clamp OR Bolt-Through Installation. 3A. DESK CLAMP 1 Open the Desk Clamp to suit the thickness of the work surface, 10-50mm (0.4-2 ). supplied. 2 Position Arm Assembly on the work surface so that the Desk Clamp hangs over the edge. Clamp Pad will automatically rotate outwards at bottom of the thread. Desk Clamp Clamp Pad TOP LOADING ATTACHMENT TIP: When sliding the Desk Clamp between two work surfaces ensure that the Clamp Pad is fully open and parallel with the edge of the work surface. 3 Close the Desk Clamp, and tighten firmly using. TIGHTEN FIRMLY Minimum gap = 18mm (0.71 ) Work Surface (top view) The unique top loading Desk Clamp allows product installation/ removal without access to the underside of the work surface. 3B. BOLT THROUGH 1 Drill an Ø8mm (5/ 16 ) hole through the work surface where you want the centre of the Base to be. NOTE: The hole should be at least 55mm (2.17 ) from any work surface edge, to allow for the diameter of the Base. 2 Select the appropriate length Fastener 45mm or 60mm depending on the work surface thickness. SHORT (45mm) suits work surface thicknesses between 13mm-28mm ( ). LONG (60mm) suits work surfaces thicknesses between 28mm-43mm ( ). 3 Centre the Base over the pre-drilled hole. Using the selected hardware, fasten the Base to the work surface. Tighten firmly. Base 28mm (1.1 ) 13mm (0.5 ) 25mm (1 ) 17mm (0.7 ) OR 43mm (1.7 ) 28mm (1.1 ) 25mm (1 ) 17mm (0.7 ) TIGHTEN FIRMLY Washer (min. x1) Fastener Use 1, 2 or 3 Washers to provide a thread length of 17-25mm (0.7-1 ) protruding above the work surface. TIP: For work surfaces thicker than 43mm (1.7 ), longer M8 bolts can be purchased from hardware stores.
3 Step 4. Tighten s 1 Gently lift and support the weight of the Upper and Lower Arms. Upper 2 Using the supplied, tighten the Upper and Lower s until the Arm Assembly supports its own weight. Lower Step 5. Attach to Monitor 1 Select appropriate hardware to fasten the mounting head to the back of the monitor. 2 Push on Cover Plate. Recessed Mounting Holes or Display with a Curved Rear Panel Cover Plate Display Mounting Screws (x4) Display Mounting Screws (x4) Spacer Bush (x4) TOP OF MONITOR Mounting Hole Mounting Hole If the Mounting Holes are recessed into the back of the monitor, or the monitor has a curved rear panel, use the Spacer Bushes supplied to pack the Mounting Holes. Step 6. Assemble onto Arm Assembly 1 Ensure that quick release buttons are in the UNLOCK position (see below). 3 Insert Screw (optional) OR Head Cap. UNLOCK LOCK Screw press in black inner button press in white outer button 2 Align and locate the onto the Quick Release coupling. Once in position, press in white outer button to LOCK. Washer DO NOT OVER TIGHTEN Head Cap Quick Release Coupling
4 Step 7. Adjust Spring Assist Upper Arm Upper Starting with the Lower Arm, tighten the until the Arm comfortably holds its position wherever it is moved. Once satisfied, repeat the process for the Upper Arm. Visual Gauge Lower Lower Arm TIP: Do not over tension! Arms should move freely, and support the weight of the monitor in any position. For multiple installations, take note of the gauge on each Arm for consistent tension. Step 8. Adjust Head Swivel Tension If necessary adjust the Head Swivel Tension using the 2mm Allen supplied. Step 9. Adjust Head Tilt Tension Depending on the weight of the monitor, make adjustments to the Head Tilt Tension using the supplied. 2mm Allen Step 10. Cable Management 1 Fully extend the Arm Assembly in the intended orientation, and remove the Cable Covers from Upper and Lower Arms. 2 Route cables along the length of the Arm Assembly and connect cables to the monitor. 3 Push cables into channels in Upper and Lower Cable Covers. Cable Cover (x2) PULL 4 Reinstall Upper and Lower Cable Covers. Push in Cable Clips (bottom half first, then top half) to lock the Covers in position. PULL TIP: Leave enough slack in the cables to allow full movement at the joints. Cable Clips (x2 sets per Arm) Installation Complete - Refer to User Operating Guide for user adjustments No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published
5 Arm Configurations Please do not remove guide from the Levitate Monitor Arm For maximum flexibility, position the Levitate Monitor Arm depending on your requirements: Maximum Reach Typical application: Touch Screen User Operating Guide For your comfort and safety please take a few moments to adjust the position of your monitor. To adjust the Levitate Monitor Arm please refer to the instructions overleaf. Maximum Height Typical application: Sit-to-Stand Compact Typical application: Desktop/Workstation Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. 15/04/2011 atdec.com.au For additional information including video demonstrations logon to atdec.com.au or levitatemonitorarm.com torarm
6 Positioning Desk Clamp When using the Desk Clamp, ensure that it is secured towards the rear of the work surface. ATTACH TO REAR OF WORK SURFACE ONLY DO NOT OVER-HANG FROM FRONT OF WORK SURFACE Adjust Spring Tension Starting with the Lower Arm, tighten the until the Arm comfortably holds its position wherever it is moved. Once satisfied, repeat the process for the Upper Arm. Upper Arm Upper Lower This puts excess pressure on the clamp, and may cause damage. Lower Arm Attaching Quick Release Head 1 Ensure that quick release buttons are in the UNLOCK position (see below). UNLOCK press in black inner button LOCK press in white outer button 2 Align and locate the onto the Quick Release coupling. Once in position, press in white outer button to LOCK. 3 Insert Screw (optional) OR Head Cap. Screw Washer DO NOT OVER TIGHTEN Head Cap TIP: Do not over tension! Arms should move freely, and support the weight of the monitor in any position. Depending on your requirements the arms can be tensioned to provide independent movement. Adjust Pan and Tilt Tension If necessary adjust the Head Swivel Tension using the 2mm Allen supplied. 2mm Allen Depending on the weight of the monitor, make adjustments to the Head Tilt Tension using the supplied. Quick Release Coupling
M4 x 14mm (x1) Silver Phillips Head Security Screw. Bolt Through Washers (x3)
SSKS SSKPB SSKW Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm Desk Mount HARDWARE 3/4/s Display Mounting s Desk Clamp VESA monitor head Arm Assembly M4 x 12/16/25mm (x4)
More informationCheck what you have received against the component checklist and hardware above.
SA71S SA71W SA71B SA71PB Component Checklist Installation Instructions SYSTEMA Systema Monitor Arm 710mm HARDWARE Display Mounting Spacers (x4) 3mm Allen Key Display Mounting Screws Arm Assembly VESA monitor
More informationCheck what you have received against the component checklist and hardware above.
SSS SSPW SSW SSPB SSB Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm HARDWARE Display Mounting Spacers (x4) 3/4mm Allen Keys Display Mounting Screws Arm Assembly VESA
More informationCheck what you have received against the component checklist and hardware above.
SSS SSPW SSW SSPB SSB Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm HARDWARE Display Mounting Spacers (x4) 3/4mm Allen Keys Display Mounting Screws Arm Assembly VESA
More informationCheck what you have received against the component checklist and hardware above.
SSS SSPW SSW SSPB SSB Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm HARDWARE Display Mounting Spacers (x4) 3/4mm Allen Keys Display Mounting Screws Arm Assembly VESA
More informationFOR SIT-STAND WORKSTATION
INSTALLATION MANUAL FOR SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs. 6017180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers...2 Base Installation Clamp Mount Base Location...3
More informationINSTALLATION MANUAL FOR PILOT WORKSTATION
INSTALLATION MANUAL FOR PILOT WORKSTATION Weight Capacity: 5-25 lbs. Monitor Weight: 5-20 lbs. 6011180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimer...2 Possible Base Mounting
More informationINFINITY MULTA SERIES
ASSEMBLY ASSEMBLY INSTRUCTIONS INSTRUCTIONS ASSEMBLY INSTRUCTIONS INFINITY MULTA SERIES Workstations, WORKSTATIONS, desks, DESKS, and AND tables TABLES with WITH powered POWERED ADJUSTMENT adjustment PARTS
More informationMultifunctional wall mount
Step6: Adjusting the display This mount provides a wealth of display adjustment to offer the best viewing from a number of seating positions. See Fig. 6. Vertical Tilt Adjustment Angle Vertical adjustment
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationUniversal Pioneer Platform (Flat Pack) 42114B/42115B
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationInstalling the Boom Mount ET 350 Monitor (Model ET 350R)
Installing the Boom Mount ET 350 Monitor (Model ET 350R) Intended Use When properly installed using the materials provided, and according to these instructions, the boom mount is intended to mount the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 33322-36889 UNDER 2007 TL Issue Date MAY 2007 PARTS LIST Front under spoiler Left bracket (Marked L ) Right bracket (Marked R ) 8 Self-tapping
More informationDetroit Speed, Inc. Mini-Tub Kit Chevy Nova, Oldsmobile Omega, Pontiac Ventura P/N: &
Detroit Speed, Inc. Mini-Tub Kit 1968-74 Chevy Nova, Oldsmobile Omega, Pontiac Ventura P/N: 041207 & 041208 Item Component Quantity 1 DSE Mini Tubs 1968-74 X-Body 2 2 Rear Upper Shock Crossmember 1 3 Upper
More informationDUETTE POWERRISE SHADES
DUETTE POWERRISE SHADES A B OPEN CLOSE INSTALLATION OPERATION CARE PRODUCT VIEW Spacer Blocks Installation Brackets End Cap Sensor Eye and Manual Button Fabric-Covered Valance PowerRise with Platinum Technology
More informationTOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27955 SIDE 2005 CIVIC SI Issue Date AUG 2004 PARTS LIST Left side under spoiler Right side under spoiler 6 Plates 8 Clips Template INSTALLATION
More informationCable Shift Linkage Kit
Cable Shift Linkage Kit INSTALLATION INSTRUCTIONS Ford column to Ford 4R70W/AODE Trans FOR PART NUMBER S: 2802650010 S INCE 1986 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 PH: (517) 424-0577
More informationCamec Keyless Entry System Installation Instructions
Camec Keyless Entry System Installation Instructions Fitment of this Keyless Entry System can be complex. Installation is recommended to be performed by certified RV installers or competent DIY. Damage
More informationQ15P. Mitsubishi MQ Triton Dual Cab
Mitsubishi MQ Triton Dual Cab Page 1 of 12 Fitting Instructions Part Number Mitsubishi MQ Triton Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationPart # Lincoln Level 2 Air Suspension Package
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 12060299 64-69 Lincoln Level 2 Air Suspension Package Front Components: 1 12060999 CoolRide Kit 1 12060601
More informationAuto-Lift Operating System
Installation Instructions Parasol Cellular Shades Auto-Lift Operating System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 STEP 1
More informationEAFT01SY FITTING INSTRUCTIONS FOTON TUNLAND 03/14- ARC BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR AIR BAG & ADR COMPLIANT VEHICLES
EAFT01SY FITTING INSTRUCTIONS REPLACES: 00.00.00 REVISED: 09.03.15 Check installation hardware before commencing. 1. Lift bonnet. FOTON TUNLAND 03/14- ARC BAR VEHICLE FRONTAL PROTECTION SYSTEM (VFPS) FOR
More informationINSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 125, 144, 200 2-Stroke KTM 250, 300 2-Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF 191-836 Manual Revision: 050307 2002 Rekluse Motor
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationInstallation Manual, Usage Tips, & Warranty Information
Installation Manual, Usage Tips, & Warranty Information Table of Contents 1. Bill of Materials page 2 2. Exploded View of RAIL ASSEMBLY page 2 3. Hardware Pictures page 3 4. Installation: Steps 1 through
More informationInstallation Guide Philips MP90 VHM Wall Mount Kit
Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationUniversal Tall HoneyBadger Chase Rack Installation Instructions
PREPARATION Universal Tall HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More informationPositioner Mount Assembly
Read all instructions carefully & check all components are present before discarding packing materials. Assembly Procedure Assembly Procedure... 1 Identify the Parts... 2 The Frame Clamp Assembly... 2
More informationCable Shift Linkage Kit
Cable Shift Linkage Kit INSTALLATION INSTRUCTIONS ididit column to Ford 4R70W/AODE Trans FOR PART NUMBER S: 2801600010, 2802600010 S INCE 1986 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 PH:
More information99-03 V6 "Shaker" System Instructions. *03 Model requires new hood Contents w/ Kit. Tool List For Appliqué:
99-03 V6 "Shaker" System Instructions *03 Model requires new hood Contents w/ Kit 1 - Hood Appliqué 1 - Aluminum Shaker Scoop 1 - Lower Air Box w/drain tube fittings (2) 1 - Upper Air Box w/cdc nameplate
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
CONTROLLED Pioneer Tray, Pioneer Platform & Pioneer Tradie Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationIE Audi 3.0T Crank Pulley Upgrade Install Guide IEBAVJ3
IE Audi 3.0T Crank Pulley Upgrade Install Guide IEBAVJ3 Thank you for purchasing your IE 3.0T crankshaft pulley upgrade! This instruction guide is used for installation of IE s lower overdrive pulley for
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationVHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications
More information(Refer to qualified personnel)
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm (Slide-Above-Arm Configuration)
More informationThe HMC-Lite Construction Guide
The HMC-Lite Construction Guide The Heavy Metal-Lite Chassis is constructed using two identical drive modules. The drive modules are constructed using 3 mechanical sub-assemblies. The drive modules are
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2505 Lowering Spindle Assembly Installation Instructions ½ TON SILVERADO
More informationPlasma Dual Swing-Out (PDS Series) Wall Mount
INSTALLATION INSTRUCTIONS Plasma Dual Swing-Out ( Series) Wall Mount The wall mount is a rugged, versatile, and installer-friendly solution to unique display mounting requirements. In addition to providing
More informationINSTALLATION INSTRUCTIONS
INSTRUCTIONS Accessory Application Publications No. 2011 CIVIC AII 44380 S 2-DOOR Issue Date AUG 2010 NOTE: The side under spoilers cannot be installed on a vehicle equipped with splash guards. PARTS LIST
More informationInstallation Manual for VHM-25 Series Arms Channel Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for VHM25 Series Arms Channel Mount Install Time: 1015 minutes The purpose of this manual
More informationPart # GM F Body Rear R-Joint Bolt-in 4 Link GM F Body Rear Bolt-in 4Link. Table of contents. Installation Instructions
Part # 11167199-1967-1969 GM F Body Rear R-Joint Bolt-in 4 Link Recommended Tools 1967-1969 GM F Body Rear Bolt-in 4Link Installation Table of contents Page 2-3... Included Components Page 4... Hardware
More informationInstallation Guide Roll Stand Kit for Philips MP20/30 Monitor
Installation Guide Roll Stand Kit for Philips MP20/30 Monitor The purpose of this guide is to: 1. Describe attachment of Post to Base (page 2). 2. Describe attachment of the Utility Basket to the Roll
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationAssembly Manual. Assembly Instructions Read Carefully 2.1. Parts included: Tools suggested: Electric Drill
2.1 Assembly Manual Tools suggested: Parts included: Electric Drill 3/8ths bit 5/16ths bit Phillips screw driver Cutting pliers 1/2 inch socket wrench 1/2 inch wrench or crescent wrench 8 mm socket wrench
More informationLexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More informationLegacy Installation Manual
Staying Home Corporation 1503 Vine Street P.O. Box 37 Harrisonville, MO 64701 816.380.2427 www.stayinghome.com A. INSTALLATION SITE REQUIREMENTS Legacy Installation Manual I. PRELIMINARY CHECKS 115 VAC,
More informationBudget Robotics Scooterbot Assembly Instructions
Budget Robotics Scooterbot Assembly Instructions The Budget Robotics Scooterbot kit is a low-cost 7" diameter servo-driven robot base, ready for expansion. Assembly is simple, and takes less than 15 minutes.
More information2016 HONDA 1000 Pioneer PN 3102 Turn signal / horn kit rev nc
2016 Honda 1000 Pioneer STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR 2016 HONDA 1000 PIONEER IF YOUR MACHINE IS NOT THIS MODEL DO NOT PROCEED. THIS KIT DOES NOT WORK ON THE PIONEER 500 nor 700 S. Contact
More informationInstallation and Service Manual
RAVE Stair Lift Installation and Service Manual WARNING! STRICT ADHERENCE TO THESE INSTALLATIONS INSTRUCTIONS IS REQUIRED to promote the safety of those installing this product, as well as that of those
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationTimes-2 Speed Files INSTALLATION INSTRUCTIONS
Times-2 Speed Files INSTALLATION INSTRUCTIONS AURORA from RICHARDS-WILCOX, INC. 600 South Lake Street Aurora, Illinois 60506 Phone: 630-897-6951 Fax: 630-897-6994 Toll Free: 800-277-1699 TIMES-2 SPEED
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationMobile TV Mount Stand with Hydraulic Height Adjustment Model: DMS-172
Mobile TV Mount Stand with Hydraulic Height Adjustment Model: DMS-172 Instruction Manual Images may be different from actual product Disclaimer It is Dyconn s intention to have all the correct information
More informationTECHNICAL SERVICE BULLETIN: TSB
TECHNICAL SERVICE BULLETIN: TSB2015-007 To: From: Global Service Organization, ichem VELOCITY and iricell Distributors Iris Diagnostics Service and Support Date: 10 June 2015 Subject: STRIP PROVIDER MODULE
More informationTusk Pannier Racks. Instructions and information KLR
1 Tusk Pannier Racks Instructions and information KLR650 2008 + Congratulations on your purchase of the Tusk Pannier Racks. These racks are made to handle extreme adventure riding, but work great for the
More informationPRE-INSTALLATION Ford F150 4WD 4" Suspension Lift Kit
2009-2013 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 25007 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front
More informationMustang V6 Shaker 99-04* Components Check List:
Mustang V6 Shaker 99-04* Components Check List: *03 Model requires new hood CDC Inspected Installer Check Quantity Descriptions 1- Hood Appliqué 1- Aluminum Shaker Scoop 1- Lower Air Box w/drain tube fittings
More informationIntroduction Date: October 2007 Pt No INSTRUCTION KIT JOINER RF 1 KIT COMPONENTS
KIT COMPONENTS Part Illustration Rear Bracket Description Front Lower Bracket KIT APPLICATION This kit is designed for use on 1595mm / 62 & 1695mm / 66 high cabinet models, incorporating the B, C, D &
More informationDown and Out Motor Mount Assembly & Installation Directions
Down and Out Motor Mount Assembly & Installation Directions Mounting the Down and Out Motor Mount correctly takes a lot of thought and a lot of planning. Please read the directions thoroughly and plan
More informationUSE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:
60-65 Ford Falcon Triangulated 4-Link Suspension Installation Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS
More informationM Damper Mount Linkage Kit Installation. Item Description Quantity Item Description Quantity Nuts 2
FANs 268.1, 1628.3 Installation Bulletin M9000-150 Issue Date 0796 M9000-150 Damper Mount Linkage Kit Installation 21 18 19 20 2 22 17 2 4 3 2 15.5 393.7 1 17 16 15 11 13 12 8 9 10 2 5 Note: Damper mount
More informationTechnical Information
Dook Lock System Diagnosis and Repair Binder -, Body Vehicle Type: / S/ Turbo Model Year: As of 03 (3) Concern: Information: Complaints and malfunctions on door lock/door locking system. This Technical
More informationAmTryke Adult Recumbent Model HP1000 #50-HC-1000
AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. UNDER 2007 CIVIC SI All 33529 Issue Date AUG 2006 PARTS LIST Rear under spoiler Clip Rubber washer 6 Flange bolts 6 Flange nuts TOOLS REQUIRED
More informationPRODUCT USE INFORMATION
9RC61000 Jeep YJ Body Lift Thank you for choosing Rough Country for all your suspension needs. This body lift fits both manual and Automatic equipped vehicles!!! Refer to last page of this Instruction
More informationOne- Touch Installation Instructions
One- Touch Installation Instructions 1 1 Height Adjustable Pivot w/ screws 9 Upper Work Surface 2 Rail Mount Knobs 10 Back Cover 3 Transformer 11 Center Pivot w/ screws 4 Support Legs 12 Left Monitor Arm
More informationPart # Galaxie Air Suspension System
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 12160298 60-64 Galaxie Air Suspension System Front Components: 1 12162401 Master Series Single Adjustable
More informationPreparation IMPORTANT! BMW K 1600 GTL EXCLUSIVE ONLY. Assembly:
BMW K 1600 GT BMW / GTL K 1600 / EXCLUSIVE GTL EXCLUSIVE SEAT INSTALLATION ADDENDUM SHEET GUIDE BMW K 1600 GTL EXCLUSIVE PRE-INSTALLATION INSTRUCTIONS Preparation IMPORTANT! BMW K 1600 GTL EXCLUSIVE ONLY
More informationRTS538 ISUZU MU-X LS-T Trackmount
Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment and report any discrepancies. Please refer to your fi tting instruction to ensure that
More informationC15C C15C. Page 1 of 20
2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket
More informationMOUNT BRACKET PARTS and HARDWARE: Installation parts with * come loose in hardware kit bag. Other parts are preassembled
INSTALL INSTRUCTIONS C-DMM-2006 Dash Monitor Mount 2017-2019 F-250, 350, 450 Pickup, F-450 and 550 Cab Chassis, 2015-2019 Ford F-150 and 2018-2019 Expedition Notes: 1. The C-DMM-2000 series Dash Monitor
More informationSS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine)
SS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine) 21/7/2010 Parts List ITEM PART NO DESCRIPTION QTY 1 570-133-200 BODY - SNORKEL (SS41HF)
More informationThe HMC Heavy Metal Chassis Construction Guide using Timing Pulleys and Belts
The HMC Heavy Metal Chassis Construction Guide using Timing Pulleys and Belts The Heavy Metal Chassis is constructed using two identical drive modules. Power can be transmitted from the motors to the wheels
More informationUse and Care Instructions: Youngman Telescopic Loft Ladder. Models: 2.6m and 2.9m. Safety
Use and Care Instructions: Youngman Telescopic Loft Ladder Models: 2.6m and 2.9m Safety Please ensure you read the Safety section in this manual starting on page 4 before installing or using the equipment.
More informationIn area - A -, a proper seal must be made against the top of the window glass.
Door window, adjusting Page 1 of 3 Audi > B3 > 1994-1998 Body Exterior, Interior 61 - Convertible top, checking and adjusting Door window, adjusting Sections C-C and D-D. Adjust door window so that window
More informationINSTALLATION INSTRUCTION BULL BAR DODGE RAM 1500 PART NUMBER
INSTALLATION INSTRUCTION 09-12 DODGE RAM 1500 PART NUMBER - 200691 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Mounting Brackets (for trucks without tow hooks
More informationStep 4 Press the sleeve gear assembly through the center of the bearing plate assembly so that the gear and bearing are in contact.
Rotational Center (ip-3009_page) : DATE: 0//207 QTY Parts Needed On This Page Tools Needed On This Page AM-303 40T Steer Gear, plated Arbor Press AM-0253 /2" ID, /2" Long Bushing 5/32 Allen Wrench AM-002
More informationVHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate (Refer to qualified
More informationPS42 - Plasma Swivel Manual Wall Mount
SHEET 1 of 9 DESIGN HIGHLIGHTS Effortless, one handed operation; even with heavy screens Bracket allows perfect parallel tracking before screen is rotated FUNCTION A manual wall bracket that allows simple
More informationSERVICE MANUAL. Stander. Seat Assembly for Permobil Power Wheelchair
SERVICE MANUAL US Stander Seat Assembly for Permobil Power Wheelchair How to contact Permobil Permobil Inc. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256 Email: info@permobilusa.com
More informationBBT006/ BBC006/ BBCD006 TOYOTA LANDCRUISER 100 SERIES IFS
INSTALLATION GUIDE BBT006/ BBC006/ BBCD006 TOYOTA LANDCRUISER 100 SERIES IFS Ironman 4x4 BBT/ BBC/ BBCD006 Bull Bars fit to a Toyota Landcruiser 100 Series (IFS). It will take about 2 hours to install.
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2013-UP FORD ESCAPE APP PART # 28-21010, 28-21015 STYLIZED RUNNING BOARD ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS
More informationPERFORMANCE HOOD VENTS CONTENTS: Left Side Hood Vent (1) Right Side Hood Vent (1) Mounting Bracket, Inner (2) Mounting Bracket, Outer (2) OE Hood Temp
CONTENTS: Left Side Hood Vent (1) Right Side Hood Vent (1) Mounting Bracket, Inner (2) Mounting Bracket, Outer (2) OE Hood Template (1) HARDWARE: Mounting Bracket, Inner X 2 Phillips Screw X 8 Mounting
More informationAGCO. Corn Header Manual d HEADSIGHT.COM
AGCO Corn Header Manual 09020401d HEADSIGHT.COM 574.546.5022 About Headsight Headsight Contact Info Headsight, Inc. 4845 3B Road Bremen, IN 46506 Phone: 574-546-5022 Fax: 574-546-5760 Email: info@headsight.com
More informationProper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.
ENGINEERING COMPANY INC. Route 145, Winthrop Road, Chester, Connecticut 06412 Phone: (860) 526-9504 Fax: (860) 526-4078 Internet: www.whelen.com Sales e-mail: autosale@whelen.com Canadian Sales e-mail:
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0030 Fits: 2007-10 135i (E82, E88; with N54 engine) 2007-08 335i/xi (E90) 2007-10 335i (E92, E93; with N54 engine) Congratulations for being selective enough
More informationSTOP---READ THIS FIRST!
STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2011-13 FORD F-250 & F350 6 & 8 LIFT KITS 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196 (559) 277-0457 FAX www.mcgaughys.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08P21-STX-200 2008 MDX BII 37680 Issue Date AUG 2007 PARTS LIST Left bracket A Left front fender flare Left bracket B Left front bumper
More informationMacBook Unibody Model A1278 LVDS Display Cable Replacement
MacBook Unibody Model A1278 LVDS Display Cable Replacement Replace the LVDS display cable in your MacBook Unibody Model A1278. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 28 INTRODUCTION
More informationRhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationC-10 Rear 4Link
Part # 11367199-1973-1987 C10 Rear 4Link Recommended Tools 1973-1987 C-10 Rear 4Link Installation Table of contents Page 2... Included Components Page 3... Hardware List & Getting Started Page 4... Disassembly
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24642 BODY SIDE CLADDING 2003 CR-V P/N 08P21-S9A-100 Issue Date OCT 2002 PARTS LIST Right rear bumper piece Right front fender piece
More informationPS42 - Plasma Swivel Manual Wall Mount Technical Sheet
DESIGN HIGHLIGHTS Effortless, one handed operation; even with heavy screens Bracket allows perfect parallel tracking before screen is rotated Bi-directional swivel motion up to 60 Strong steel construction
More informationCORN HEADER MANUAL: CNH PRE-2012
CORN HEADER MANUAL: CNH PRE-2012 09020201c HEADSIGHT.COM 574.546.5022 About Headsight Headsight Contact Info Headsight, Inc. 4845 3B Road Bremen, IN 46506 Phone: 574-546-5022 Fax: 574-546-5760 Email:
More informationFitting Instructions
Reverse Park Assist Suitable for: Nissan Navara Kit Part No: 5466XX NP00 Tow-Pro Wiring Kit Fitting Instructions Accessory Kit Estimated Fitting Time: 0 Minutes FI98 Page 0 of 5 General Notes Read through
More information