Models Affected: 2009 through 2012 Model Year GM 8.1 Propane Vision Models CORRECTIVE ACTION ---- PROCEDURE
|
|
- Toby Williamson
- 5 years ago
- Views:
Transcription
1
2
3 Models Affected: 2009 through 2012 Model Year GM 8.1 Propane Vision Models ISSUE Bus will start if fuel door is either open or closed if the circuit is broken by a blown fuse or tripped circuit breaker. CORRECTIVE ACTION ---- Update fuel fill door wiring circuit to eliminate fuse or circuit breaker so bus will not start when the fuel fill door is open. PROCEDURE WARNING: Always follow all Federal, State, And Local and Shop safety standards and use proper safety equipment when performing these procedures. Observe all safety precautions to secure the bus from rolling. 1. Park the bus on a level surface, apply parking brakes, turn off engine and remove keys. Chock wheels. 2. Disconnect batteries Note; When disconnecting the batteries, remove the negative cable first. 3. Remove chassis Power Distribution Unit (PDU) cover by unscrewing two thumb screws. The thumb screws are located at the top of each side of the cover. Thumb screws. Cover is located lower center of dash. --S E R V I C E B U L L E T I N----S 1 1 T C----- Page 1 of 6
4 4. Locate FUEL DOOR + fuse shown on PDU decal on reverse side of PDU cover removed in previous step. Remove fuse (no longer required). 5. Locate RED wire labeled FUEL DOOR + that is connected to this fuse position. Remove this wire and cut off terminal. Crimp on new terminal # and connect to PDU ground stud. (Torque ground stud nut 11 to 15 FT LBS) See examples below of PDU layouts with single zone and dual zone multiplex. PDU Ground Stud Single Zone Multiplex Chassis PDU Layout Shown Above: PDU Ground Stud FUEL DOOR + Fuse FUEL DOOR + Fuse Dual Zone Multiplex Chassis PDU Layout Shown Above: Page 2 of 6
5 6. On buses with a Single Zone Multiplex locate the RED wire in connector C703 cavity position 26. This circuit routes to a splice located approximately two inches from multiplex module connectors A thru D. This circuit will be labeled AC-102 or AC-102A. Cut this side of the circuit from the splice. Tape splice where circuit was removed. Re-splice the removed circuit to the Tan wire AC-016 (Vandal Lock) located in module connector C cavity position 16 using butt splice terminal # This terminal has an 18/22 gauge cavity and a 14/16 gauge cavity. Use the 14/16 cavity for the two circuits spliced together. See examples below of Chassis PDU layout with single zone multiplex. 7. Reconnect batteries Note, connect positive cable first. Switch ignition key on. Verify with fuel fill door open that A Zone, Port 3, Input 8 LED is ON. Verify engine starter will NOT engage with fuel fill door opened. Replace chassis PDU cover. Update complete. Connector C703 Cavity 26 Connector C Cavity 16 Page 3 of 6
6 8. On buses with a Dual Zone Multiplex locate the RED wire in module connector C cavity position 11. This circuit will be labeled FUEL DOOR IN10. Remove circuit from connector. Butt splice FUEL DOOR IN10 circuit to wire assembly # Route the wire assembly following along the PDU harness over the steering column to the body electrical panel area under the driver side window. Secure assembly with tie cable # See PDU layout with dual zone multiplex below. Dual Zone Multiplex Chassis PDU Layout Shown Below: Connector C Cavity 11 Page 4 of 6
7 9. On buses with a Dual Zone Multiplex insert terminal end on wire assembly from previous step into body control module connector A cavity 13. If optional wire is already in cavity 13 DO NOT remove. Cut terminal off supplied assembly from previous step and splice to existing wire in cavity 13 using butt splice terminal # This terminal has an 18/22 gauge cavity and a 14/16 gauge cavity. Use the 14/16 cavity for the two circuits spliced together. Dual Zone Multiplex Body Electrical Panel Layout Shown Below: Connector A Cavity 13 Page 5 of 6
8 10. Reconnect batteries Note, connect positive cable first. Switch ignition on. Verify with fuel fill door open that B Zone, Port 1, Input 7 LED is ON. Verify engine starter will NOT engage with fuel door opened. Replace chassis PDU cover. Update complete. PARTS PART NUMBER NPN QUANTITY DESCRIPTION Terminal, Eyelet, 3/8, GA, Insulated Terminal, Butt Conn, Step Down, 18-22/14-16 Tie, Cable, 18 LB Harness, Wrg, Fuel Fill Door Switch S11TC Black Electrical Tape TOOLS Wire Cutters Wire Strippers Crimper for Butt Connector Tool Terminal Removal Deutsch (BB # ) Tool Terminal Removal Narrow Pick (BB # ) Page 6 of 6
2011 Model Year BBCV Vision and Model Year D3 All American CORRECTIVE ACTION ---- PROCEDURE
Cruise Control May Not Deactivate 2011 Model Year BBCV Vision and 2010-2011 Model Year D3 All American ISSUE Once activated the cruise control feature may not deactivate as designed when the service brakes
More informationModels Affected: Certain 2013 Model Year Propane Vision Buses Equipped with Ford 6.8L Engines CORRECTIVE ACTION ---- PROCEDURE
Models Affected: Certain 2013 Model Year Propane Vision Buses Equipped with Ford 6.8L Engines ISSUE Certain 2013 model year propane Vision buses equipped with Ford 6.8L engines may not have the service
More informationModels Affected: Certain 2014 Model Year Vision Buses Equipped with Ford 6.8L Propane Engines ISSUE
R E C A L L C A M P A I G N ----R 1 3 W G -- Adjustment Inspection ISSUE CORRECTIVE ACTION ---- Models Affected: Certain 2014 Model Year Vision Buses Equipped with Ford 6.8L Propane Engines On affected
More informationA qualified repair technician should perform Service Bulletin S04JC. You may contact your appropriate Blue Bird distributor for assistance.
October 20, 2004 Dear Blue Bird Owner: You will find enclosed Service Bulletin S04JC regarding a modification to the Multiplex system on certain Blue Bird "Vision" school buses. We recommend that Service
More informationSERVICE PROCEDURE. Revision 1 updated Table 1 to include old / new part number combination C91 / C92.
SERVICE PROCEDURE G-08506 R1 MARCH 2009 SUBJECT: SAFETY RECALL (U.S.) IDM FUSE BLOCK on certain INTERNATIONAL 3200, 3300, and IC Bus BE, CE, HC, RE models built 9/21/01 thru 12/31/07 with an INTERNATIONAL
More informationModels Affected: Visions with Propane Engines CORRECTIVE ACTION ---- PROCEDURE
Propane Belt Squeal Models Affected: Visions with Propane Engines ISSUE Front End Accessory Drive (FEAD) Belt chirping/squealing caused by improper fore-aft crankshaft pulley positioning. CORRECTIVE ACTION
More informationjegs.com
Contents Wiring Harness w/ Fuse Panel Installation Instructions Turn Signal Plug w/ Terminals 2 Headlight Plugs 3/4 Grommet 10 ¼ Terminals 4 Ring Terminals 10 Wire Ties Fusible Link 2 Screws & Nuts 2 Plastic
More informationWiring Harness Update Kit Assembly Instructions Treker 4200/4400 NT & ST Series Manual No M
Wiring Harness Update Kit Assembly Instructions Treker 4200/4400 NT & ST Series Manual No. 700-364M Before You Start! When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationw w w. h d o n l i n e s h o p. d e CHROME FAN KIT GENERAL INSTALLATION -J04347 REV Kit Number Models Kit Contents
-J0447 REV. 008-08-05 CHROME FAN KIT GENERAL Kit Number 996-08 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationAux. Battery and Isolator
Aux. Battery and Isolator ISOLATOR MOUNTING ALL YEAR VANAGONS Fig.1 1. Disconnect ground from main battery under passenger seat 2. Remove driver seat 3. Remove driver seat belt buckle from seat pedestal
More informationTerminal Tractor Service Bulletin Subject: Forward Facing Flood Lights w/ LED Light Bar Field Rewire Modification Product: Medium Terminal Tractor
Page 1 of 6 Units Affected: FedEx Ground Kalmar Ottawa T2 terminal tractors built between chassis serial numbers; 346358 and 346471. Possible Situation: The fuse holder is melting due to high current demand
More informationATTENTION. Custom Dynamics UTV Turn Signal Kit Installation Instructions
Custom Dynamics UTV Kit Installation Instructions We thank you for purchasing the Custom Dynamics UTV LED Kit. Our products utilize the latest technology and high quality components to ensure you the most
More informationMazda North American Operations Irvine, CA
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: REMOTE START CAUSES HVAC1 OR IGN1 FUSE TO BLOW - INSTALL LOAD REDUCTION RELAY SERVICE HARNESS Bulletin No: 01-046/08 2007-2008
More informationPOWER DISTRIBUTION SYSTEMS
DN POWER DISTRIBUTION SYSTEMS 8O - 1 POWER DISTRIBUTION SYSTEMS TABLE OF CONTENTS page AND POWER DISTRIBUTION SYSTEM....1 POWER DISTRIBUTION CENTER...1 GENERATOR CARTRIDGE FUSE....2 JUNCTION BLOCK...2
More informationE-Z POWER TONNO Installation Instructions Full Size Ford & GM Pick Up 6 1/2 Ft. Box
E-Z POWER TONNO Installation Instructions Full Size Ford & GM Pick Up 6 1/2 Ft. Box P/N 8W04-TN-0000A-A 1. Required Tools: 3/8 Socket set and Ratchet Rivet Gun 5mm Allen Wrench Open box and remove all
More informationWe have had a request for instructions on how to replace the 50 AMP CR relay in the A/C electrical box with the upgraded 70 AMP relay.
We have had a request for instructions on how to replace the 50 AMP CR relay in the A/C electrical box with the upgraded 70 AMP relay. This Carolina Thomas Bus Buzz provides instructions as to how we go
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E50-TK6-100 Application 2010 FIT (BASE MODEL) Publications No. AII 42212 Issue Date AUG 2009 The security system will only work if the vehicle is equipped with
More informationTHE safety accessory of the 21 st Century.
00 006 Chevrolet SSR Signal Mirror Installation Instructions THE safety accessory of the st Century. Note: Professional Installation Recommended Warranty does not cover damage to the vehicle or mirror
More informationPage 1 of 9 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1985 Dodge Truck D 350 Pickup V8-360 5.9L VIN I
More informationFront Fog Lamp Package Installation
Service Information 2014 Cadillac SRX SRX VIN N Accessory Installation Manual Accessories Electrical Accessories Accessories Document ID: 2242151 Front Fog Lamp Package Installation Table 1: Table 2: Kit
More informationINSTRUCTIONS. 20 Circuit Wiring Kit Instructions October 2009, Speedway Motors, Inc.
1 MAIN FUSE PANEL The main fuse panel harness s designed to be mounted under the dash a the firewall in an area close to the steering column. The enclosed representation of the main dash harness shows
More informationFitting Instructions
Tow-Pro Wiring Kit Fitting Instructions Holder Colorado / Colorado 7 Accessory Kit Estimated Fitting Time: 0 Minutes FI7 Page 0 of General Notes Read through the fitting instructions before installation
More informationJUNCTION BLOCK DESCRIPTION OPERATION XK 8W-97 POWER DISTRIBUTION 8W
XK 8W-97 POWER DISTRIBUTION 8W - 97-7 JUNCTION BLOCK DESCRIPTION An electrical Junction Block(JB) is concealed beneath the driver side of the instrument panel in the passenger compartment of the vehicle.
More informationCustom Dynamics Spyder Stingerz Installation Instructions
Custom Dynamics Spyder Stingerz Installation Instructions We thank you for purchasing the Custom Dynamics Stingerz! Our products utilize the latest technology and high quality components to ensure you
More informationTrail Rocker Installation Instructions
Trail Rocker Installation Instructions Manual #90580 For Installing Painless Part Numbers: 57000 and 57001 Painless Performance Products recommends you, the installer, read this installation manual from
More informationTrail Rocker Installation
Trail Rocker Installation Instructions Customizable Trail Rocker Control System For Installing Painless Part Number: 57100 Manual #90616 Painless Performance Products recommends you, the installer, read
More informationELECTRONIC DASHBOARD GAUGE DROP-OUT CX, CV AND CH MODEL CHASSIS
SERVICE BULLETIN (Also applies to Mack Trucks Australia) (Supersedes bulletin SB-732-005 dated 12/10/02) NUMBER: SB-732-005 DATE: 1/13/03 MODEL: CX, CV, CH ELECTRONIC DASHBOARD GAUGE DROP-OUT CX, CV AND
More informationAccessory Kit Estimated Fitting Time: 120 Minutes
Landcruiser LC00 Tow-Pro Wiring Kit - Landcruiser LC00 Kit Part No: TPWKIT - 005 Accessory Kit Estimated Fitting Time: 0 Minutes FI88 Page 0 of Issue: Date: 7/09/07 07 General Notes Safety Notes Parts
More informationISIS Power Manual and Installation Guide Race Car Replicas- Superlite Coupe
ISIS Power Manual and Installation Guide Race Car Replicas- Superlite Coupe Table of Contents Overview... 2 System Details... 3 Kit Includes... 3 Technical Specifications... 3 Harness Descriptions... 4
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Chassis Harness with RCA (Note: In some cases a RCA
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More information2006+ Toyota Yaris Remote Start Wiring Guide
2006+ Toyota Yaris Remote Start Wiring Guide Note: This guide assumes that the user has a good working knowledge of automotive electrical systems. The user assumes all liability for any damage resulting
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford F-250 to F-750 Pick-Up, Super-Duty 1998-2007 Trailer Tow Mirror Ford Excursion XLT/Limited 2000-2002 Trailer Tow Mirror Ford Excursion (all models) 2003-2005
More informationSystem Date of Issue Bulletin Number Bulletin Type. Title: Elimination of AC Connectors J29a and J29b
System Date of Issue Bulletin Number Bulletin Type Odyne System G2V2 2/4/15 Rev. 10/6/15 00020 Field Service Action Technical Service Bulletin Technical Service Advisory Title: Elimination of AC Connectors
More informationRUN/BRAKE/TURN AUXILIARY LIGHTS J
RUN/BRAKE/TURN AUXILIARY LIGHTS J06236 2018-05-31 GENERAL Kit Numbers 67800589A, 69202276 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harleydavidson.com
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE STARTER IMMOBILIZER MODEL 102 CONTENTS System Features... 1 Technical Assistance... 1 System Components... 1 Required Tools... 1 Precautions... 1 Making Wiring Connections...
More informationTools you will need: Screwdrivers, Metric Sockets, Hook and Loop Tape or Zip Ties, Shop Light, Wire cutters, Wire crimping tool
Overview: This guide provides instruction for installing Adventure Wagon s Auxiliary Battery Tray and the charging bundle. Package Contents: Adventure Wagon Battery Tray includes the tray plus mounting
More informationAccessory Kit Estimated Fitting Time: 120 Minutes (Prado) Estimated Fitting Time: 140 Minutes (Kluger)
Tow-Pro Wiring Kit - Toyota Kluger / Prado Accessory Kit Estimated Fitting Time: 0 Minutes (Prado) Estimated Fitting Time: 0 Minutes (Kluger) FI99 Page 0 of Issue: Date: 0/0/0 0 General Notes Read through
More informationINSTALLATION GUIDE PRISONER TRANSPORT LIGHTING. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE PRISONER TRANSPORT LIGHTING STRONG RELIABLE SECURE pro-gard.com 800.480.6680 THESE COMPONENTS ARE REQUI TO INSTALL THE PRO-GARD PRISONER TRANSPORT LIGHTING 3" Round LED Lighthead QTY=
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for (2005-2008) Proper service and repair procedures are vital
More informationSignal Mirror Installation Instructions Standard West Coast Mirror
Signal Mirror Installation Instructions Standard West Coast Mirror THE safety accessory of the 21 st Century. P/N 210-0058-0 Rev A1 (6-29-04), GG 2002 Muth Mirror Systems, LLC. Note: Professional Installation
More informationAdjustable Light Kits E-Z-Go TXT All Models Installation Instructions
Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 12035 SYSTEM 2012 RIDGELINE Issue Date NOV 2011 PARTS LIST Security System Attachment Kit: P/N 08E55-SJC-101 Flange bolt Unit bracket
More informationIn This DIY We Will Show You How To Install Recon Backup Lamps (part # To Run On A Separate Switch & In Reverse.
In This DIY We Will Show You How To Install Recon Backup Lamps (part # 264150 To Run On A Separate Switch & In Reverse. Please Note, There Are Many Ways of Installing These Lights, Including Wiring Methods,
More informationTrail Rocker Installation Instructions
Trail Rocker Installation Instructions Manual #90581 For Installing Painless Part Numbers: 57002 Painless Performance Products recommends you, the installer, read this installation manual from front to
More informationFitting Instructions
Reverse Park Assist Suitable for: Nissan Navara Kit Part No: 5466XX NP00 Tow-Pro Wiring Kit Fitting Instructions Accessory Kit Estimated Fitting Time: 0 Minutes FI98 Page 0 of 5 General Notes Read through
More informationBX8848 Installation Instructions 4 Diode Wiring Kit For Motorhomes With Red Tail Lights
For Motorhomes With Red Tail Lights WARNG: Incorrect wiring may result in blown fuses, damaged wiring, fire, or bodily injury. Blue Ox recommends installation of this kit by a trained professional. Blue
More informationINSTALLATION INSTRUCTION
1551 S. Vineyard Avenue Ontario, CA 91761 (909) 923-1973 INSTALLATION INSTRUCTION Club Car Precedent Installation Notes CURTIS 1234, 1236 OR 1238 AC INDUCTION MOTOR/ CONTROLLER REVISION: B This kit is
More informationTrack Rocker Installation Instructions
Track Rocker Installation Instructions Customizable Track Rocker Control System For Installing Painless Part Number: 58100 Track Rocker Relay Center Manual #90641 Painless Performance Products recommends
More informationInstallation Instructions for Key Switch SNOWRATOR
2017 Installation Instructions for Key Switch SNOWRATOR We appreciate your purchase of L.T. Rich s Product. Please read carefully before Operating or detaching. AES L.T.RICH 6/15/2017 SHIPPING CONTENTS...
More informationTOYOTA YARIS HATCHBACK TVIP V3 (RS3200) Preparation
Preparation Part Number: 08586-53810 Kit Contents Item # Quantity Reqd. Description 1 1 V3 ECU 2 1 Piezo Buzzer 3 1 Wire Harness 4 1 ECU Mounting Bracket 5 2 Remote Control Transmitter 6 1 Butyl Tape 7
More informationTRAIL CHARGER with EXTENDER and COMBO NOSE BOX
TRAIL CHARGER with EXTENDER and COMBO NOSE BOX 284424 01 Version 1.02 03/14/2011 Owners Manual Operation Installation Wiring Diagram Troubleshooting Parts Breakdown 1 GENERAL OPERATION PROBLEM On applications
More informationThis harness kit includes: Civic harness (2003 to 2005) Installing the Hybrid ReVolt Universal grid charger in a First Gen Civic ( )
Installing the Hybrid ReVolt Universal grid charger in a First Gen Civic (2003-2005) This harness kit includes: Civic harness (2003 to 2005) (a) 1 HV warning label (c) 1 charger connector cover (e) 4 #6
More informationROADRELAY 5 Installation Guide
ROADRELAY 5 Installation Guide ROADRELAY 5 Installation Guide Bulletin No. 4971214 Revision A Copyright 2011, Cummins Inc. All rights reserved. Cummins Inc. shall not be liable for technical or editorial
More informationCSI-100 Installation Instructions
CSI-100 Installation Instructions Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting
More informationSMART ELECTRIC TAILGATE LIFT SYSTEM Document # Created ACH 09/19/2018 Revised ACH 10/02/18 A2
Document #730141 Created ACH 09/19/2018 Revised ACH 10/02/18 A2 General Applicability: 2018- KIA Sedona Issues N/A Kit Contents: Item# Component Description 1 Stay Bar (Strut)(right) 2 Stay Bar (Strut)(left)
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW
More informationGentex by VOXX Corporation Installation Instructions
Gentex by VOXX Corporation Installation Instructions KIT CONTENTS: Item Qty Part Number Description 1 1 of the following: ADVGEN2A 7 Pin Auto-Dimming Mirror ADVGEN5A 7 Pin Auto-Dimming Mirror with Compass
More informationFOG-LAMPS INSTALL KIT
FOG-LAMPS INSTALL KIT DODGE RAM (BR, BE) Installation Instructions Read entire instructions thoroughly before starting. For proper removal and installation, follow procedures in the service manual. NOTES:
More informationSYSTEM OPERATION IMPORTANT CAUTIONS
SYSTEM OPERATION The system is turned on by placing the gear shift lever in the reverse position. The green light on the cab Control Box will illuminate to indicate the system is operating. When an object
More informationw w w. h d o n l i n e s h o p. d e HEATED HAND GRIP KITS GENERAL REMOVAL -J02983 REV Kit Number Models Kit numbers Service Parts
-J098 REV. 007-0-0 GENERAL Kit Number 56047-0B, 5607-0B, 5674-0B, 5696-0B, 565-0B, 5669-0A, 56694-04A, 56750-04A, 5688-0A, 569-05, 5696-05, 56997-07 Models For model fitment information, please see the
More informationJD TRIPLE EGRESS TRIPLE EGRESS SECTION
JD 52-5525 TRIPLE EGRESS TRIPLE EGRESS SECTION 5525 EGRESS 5-1 ASSEMBLY - TRIPLE EGRESS, CAB TRIPLE EGRESS MOUNTING Park the tractor on a flat, hard, level surface. Lower both side decks down onto the
More informationInstallation Instructions
Installation Instructions for EVS II Security and Keyless Entry Systems Note: It is recommended that this installation take place prior to rustproofing. The individual delivering the vehicle should review
More informationTOYOTA CAMRY wo/smart entry TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: 08586-3T950 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 RES ECU 3 1 BUS ECU 4 1 ECU Mounting Bracket (A) 5 1 ECU Mounting Bracket (B) 6 1 Butyl Tape Hardware
More informationTurfDefender Electronic Leak Detector Kit Reelmaster 5000, 6000 and 5010 Series Traction Units
Form No. 56 586 Rev A TurfDefender Electronic Leak Detector Kit Reelmaster 5000, 6000 and 500 Series Traction Units Model No. 05 Installation Instructions The Installation Instructions for Reelmaster 5000/6000
More informationZeon Control Pack Relocation Kit 78 Cable Length
ORIGINAL INSTRUCTIONS SYMBOL INDEX SYMBOL EXPLANATION SYMBOL EXPLANATION Read All Product Literature Always Wear Leather Gloves Always Wear Hearing and Eye Protection Do Not Move People Zeon Control Pack
More informationCHEVORLET IMPALA
1962-64 CHEVORLET IMPALA Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 1 deck lid harness 4 grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN
More informationINSTALLATION INSTRUCTIONS
Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness
More informationModel A Turn Signal Kit Installation Guide
Model A Turn Signal Kit Installation Guide Creative Connections, Inc. Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/K 2008 Creative Connections, Inc.
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW
More informationMINOTOUR SERVICE MANUAL
MINOTOUR SERVICE MANUAL The following areas are covered in this manual: Interlock Feature Vandalock Feature AC System Heaters Passenger Advisory System MINOTOUR SERVICE MANUAL ELECTRICAL TROUBLESHOOTING
More informationTL UNIVERSAL WIRING PROCEDURE
UNIVERSAL WIRING PROCEDURE 3nov11jh TABLE OF CONTENTS 1 Control Kits 1.1. TIK10100 Universal Manual Hand Control 1.2. TIK10103 Universal Automatic Foot Control for Hydraulic Brakes 1.3. TIK10104 Universal
More informationCSI-300 Installation Instructions
CSI-300 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces
More informationSAISBM V36W Installation Instructions
The Original Secondary Air Injection System Bypass Kit SAISBM V36W Installation Instructions All Applicable Toyota/Lexus Vehicles Introduction: The Secondary Air Injection System (SAIS) bypass module is
More informationService Bulletin Published by Sudden Service, Inc.
Service Bulletin Published by Sudden Service, Inc. Volume 09 / Number 3 / May 15, 2009 Louisville, Mississippi Pre-operational checks of the MM80 Pack-Rat should be performed before each use in order to
More informationFord 6.7L Installation of the Guardian Safety System
Ford 6.7L Installation of the Guardian Safety System Diesel Tech Industries Ltd. 14215-120 Avenue Edmonton, Alberta, Canada T5L 2R8 Phone: (780) 455-9876 info@dtiguardian.com www.dtiguardian.com DTI05-02.01/13
More informationMY F150 CrewCab 1. Tools Required E F G. Page 1 of 10 9L3J-19A014-AA Copyright Ford 2013 FoMoCo
2009-2014MY F150 CrewCab 1 Tools Required A B C D 3X E F G H 2X I 6X 3X Page 1 of 10 9L3J-19A014-AA Copyright Ford 2013 FoMoCo 2009-2014MY F150 CrewCab 2 Subwoofer Power Wire Routing All Vehicles WARNING:
More informationAEROMOTIVE Part # INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 16302 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried
More information2500 LB ELECTRIC A-FRAME JACK OWNER S MANUAL
2500 LB ELECTRIC A-FRAME JACK OWNER S MANUAL SPECIFICATIONS: Models Applicable: 2500 lb Electric A-Frame Jack Maximum Lift Capacity: 2500 lbs (continuous use) Retracted Height: 31 3 /8 Vertical Travel:
More informationUSB Charge Port Installation Instructions
USB Charge Port Installation Instructions Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0014C Thank you for purchasing a Logo Lites USB Charge Port! USB Charge
More informationCSI-400 Installation Instructions
CSI-400 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces
More informationSST-3 Start-Stop-Throttle
SST-3 Start-Stop-Throttle Installation & Operation Guide Revision 1.1 Internet: www.wiredrite.com E-mail: info@wiredrite.com Page 1 CONTENTS Introduction 2 Hardware Mounting 2 Connections 2 Operation &
More informationWater in Fuel Sensor Kit
03/08/2016 1050355-1050356 Water in Fuel Sensor Kit (I-00369) 1 Water in Fuel Sensor Kit Fast and Accurate Detection of Water in Diesel Fuel 1050355 Universal Kit For use with BD FlowMax water separator
More informationService Bulletin Published by Sudden Service, Inc.
Service Bulletin Published by Sudden Service, Inc. Volume 07 / Number 3 / June 13, 2007 Louisville, Mississippi Electrical System Maintenance Requirements Taylor Machine Works, Inc. has developed electrical
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E10-TP6-100 Application 2010 ACCORD CROSSTOUR Publications No. AII 41935 Issue Date NOV 2009 PARTS LIST TOOLS AND SUPPLIES REQUIRED Ambient Light Kit Ambient
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford F-250/F-350 Pick-Up, Super-Duty 1998-2006 Ford Excursion XLT/Limited 2000-2002 Ford Excursion (all models) 2003-2006 THE safety accessory of the 21st Century.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 23086 SYSTEM CR-V Issue Date NOV 2001 PARTS LIST Security System P/N 08E51-EP4-100 Security System Attachment P/N 08E55-S9A-100 Security
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationM GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET
Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following
More informationChrysler 45RFE Tailmount Automatic Transmission Shifter Installation Instructions
Chrysler 45RFE Tailmount Automatic Transmission Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Chrysler 45RFE Tailmount
More informationSide Door Sill Trim Plate Package Installation
Page 1 of 5 2014 Chevrolet Equinox Equinox, Terrain VIN L Accessory Installation Manual Accessories Interior Accessories Accessories Document ID: 3619390 Side Door Sill Trim Plate Package Installation
More informationINSTALLATION INSTRUCTIONS
2015 Silverado Qi Wireless Charging Kit (Kit # FDMC-1276) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Qi Wireless Charging Module
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationGentex by VOXX Corporation Installation Instructions
Gentex by VOXX Corporation Installation Instructions Bezelled ADVGEN45A4 Bezelled w/ Homelink ADVGEN80EXP ADVGEN45A4PW4 ADVGEN40A4 Frameless ADVGEN8EXP Frameless w/ Homelink ADVGEN85EXP ADVGEN45AB5 TOOLS
More informationINSTRUCTION, GPT LOW VOLTAGE THERMAL SWITCH (LVTS) INSTALLATION KIT P/N
LIFT CORPORATION Sht. 1 of 9 DSG# M-07-18 Rev. ~ Date: 08/15/08 INSTRUCTION, GPT LOW VOLTAGE THERMAL SWITCH (LVTS) INSTALLATION KIT P/N 282473-01 LOW VOLTAGE THERMAL SWITCH (LVTS) P/N 905291 INSTRUCTION
More informationTOYOTA HIGHLANDER w/o Smart Key TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: PT398-48111 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory Kit Contents Item # Quantity Description 1 1 Wire Harness
More informationA selection of phillips head screwdrivers 15mm socket 10mm socket Modeler s knife Solder Electrical tape A selection of flat head screwdrivers
Read entire instructions thoroughly before starting. References to the service manual wiring diagrams and operation sections will be required for adjustments, fastener torques, and troubleshooting. TOOLS
More informationBXD Battery Disconnect
INSTALLATION MANUAL BXD Battery Disconnect Installation Manual BATTERY DISCONNECTS provides a simple and safe means of disconnecting the coach and chassis battery(s) of an RV. With just the touch of a
More information