On-the-Job Training Program. Overview of Training Programs

Transcription

1 On-the-Job Training Program Overview of Training Programs

2 The training programs are as follows: Code Training Program Hours (Up to) 901 Carpenter, Rough Concrete Finisher (Paving) Concrete Finisher (Structures) Form Builder (Structures) Form Setter (Structures) Piledriver Pipe Layer Asphalt Paving Machine Bulldozer, Over 150 H.P Concrete Paving Finishing Machine Backhoe Crane or Excavator Front End Loader (2½ C.Y. and Less) Front End Loader (Over 2 1/2 C.Y.) Motor Grader Operator Roller, Steel Wheel (Plant Mix Pavements) Roller, Steel Wheel (Other-Flatwheel or Tamping) Roller, Pneumatic (Self-Propelled) Scrapers (Over 17 C.Y.) Tractor Operator (80 H.P. and Less) Tractor Operator (Over 80 H.P.) Trenching Machine, Heavy Reinforcing Steel Setter (Structures) Steel Worker (Structural) Foundation Drill Operator Mechanic Welder Crusher or Screening Plant Operator Truck Driver Asphalt Distributor Asphalt Raker Blaster Spreaderbox Person Sign Erector Oiler Utility Operator Service Person Electrician Batching Plant Scaleperson Wagon Drill, Boring Machine or Post Hole Driller Operator Reinforcing Steel Setter (Paving) Form Setter (Paving) Self Propelled Sweeper Operator Bulldozer, Under 150 H.P Scrapers (Under 17 C.Y.) 520 2

3 CARPENTER, ROUGH Code 901 I. Orientation and Safe Use of Tools of the Trade A. Power and hand tools hours B. Materials selection hours II. Applied Techniques of Highway Construction Carpentry B. Pier, pile and cap formwork hours C. Decking formwork hours D. Parapet and hand railing formwork hours E. Endwall formwork hours F. Box culverts, inlets and headwall formwork hours III. Blueprint or Construction Plans Reading and Application hours IV. Basic Form Design Familiarity hours V. Stripping and Salvage of Forms for Re-use hours A. Safety Procedures... 5 hours Total hours 3

4 CONCRETE FINISHER (Paving) Code 902 B. Observation of use of straight edges and steel trowels hours C. Observation of forming a finishing of edges and joints hours B. Routine cleaning work area and materials, holding materials, tools and handling canvas belting or burlap strips hours A. Safe operating procedures hours B. Basic operation of tools hours C. Use of straight edges or steel trowels hours D. Forming and finishing edges, joints, curbs and gutters hours Total hours 4

5 CONCRETE FINISHER (Structures) Code 903 B. Observation of use of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures hours B. Basic operation of machine hours C. Use of trowels or floats hours D. Operation of trowels or floats or finishing machine hours Total hours 5

6 FORM BUILDER (Structures) Code 904 I. Orientation and Safe Use of Tools of the Trade A. Power and hand tools hours B. Materials selection hours II. Applied Techniques of Highway Construction Carpentry B. Pier, pile and cap formwork hours C. Decking formwork hours D. Parapet and hand railing formwork hours E. Endwall formwork hours F. Box culverts, inlets and headwall formwork hours III. Blueprint or Construction Plans Reading and Application hours IV. Basic Form Design Familiarity hours V. Stripping and Salvage of Forms for Re-use hours A. Safety Procedures... 5 hours Total hours 6

7 FORM SETTER (Structures) Code 905 B. Observation of placing of forms hours C. Observation of form stripping and setting of precast concrete hours B. Help strip forms and clean work area hours III. Actual Operation of Form Setting A. Safe operating procedures... 5 hours B. Hold and help align forms. Drive stakes for braces and help erect scaffolding hours C. Observe and assist in setting precast concrete hours D. Measure space between forms, fit together, line, plumb vertically, set to elevation hours E. Check forms while concrete is being poured hours Total hours 7

8 PILEDRIVER Code 906 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures hours B. Basic operation of crane or pile driving rig in hoisting and moving hours C. Placement of pile in preparation for driving hours D. Seating of pile hammer on pile in preparation for driving hours E. Driving of pile hours Total hours 8

9 PIPE LAYER - Code 907 B. Observation of spade operation and laying of pipe hours C. Study of various types of pipe and related materials... 5 hours B. Ditch preparation, handle materials and tools hours III. Actual Handling of Pipe and Spade A. Ditch grading with compressed air driven or hand spade hours B. Handle materials, assist in lowering pipe hours C. Work with pipe layer in laying all types of pipe and duct. Adjust pipe to elevation insert spigot end of pipe into bell end of last laid pipe hours Total hours 9

10 ASPHALT PAVING MACHINE - Code 908 B. Observation of machine in operations hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safety operating procedures... 5 hours B. Observation of machine in operations hours C. Operating of machine hours Total hours 10

11 BULLDOZER, over 150 H.P. - Code 909 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Movement and stockpiling of material hours C. Pushing and rough grading hours D. Clearing and grubbing hours E. Finish grading hours F. Special applications hours Total hours 11

12 CONCRETE PAVING FINISHING MACHINE - Code 910 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Screed regulation indoctrination and operation hours C. Operation of machine hours Total hours 12

13 BACKHOE Code 911 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Trenching operations (for Pipe laying, etc.) hours C. Excavation (for structures, footings, etc.) hours D. Special applications and functions hours Total hours 13

14 CRANE OR EXCAVATOR Code 912 A. Safety procedures hours B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours A. Safety procedures hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures hours B. Excavation for footings and removal of unsuitable materials hours C. Loading and unloading materials hours D. Trenching for pipe, etc hours E. Hoisting materials hours F. Placement of beams, pipe, girders, piles, etc hours Total hours 14

15 FRONT END LOADER (2½ C.Y. and less) Code 913 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Loading materials hours C. Excavation hours D. Special applications hours Total hours 15

16 FRONT END LOADER (Over 2 1/2 C.Y.) Code 914 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Loading materials hours C. Excavation hours D. Charge hoppers with materials on asphalt and concrete plants hours E. Special applications hours Total hours 16

17 MOTOR GRADER OPERATOR Code 915 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Scraping and leveling dirt on roadway hours C. Spreading and mixing materials on roadway hours D. Shaping and blading subgrades hours E. Balancing and rough shaping base course materials hours F. Fine grading and dressing of shoulders and slopes hours Total hours 17

18 ROLLER, STEEL WHEEL (Plant Mix Pavements) - Code 916 B. Observation of machine in operation hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Roll base course to desired compaction hours C. Roll asphalt surfaces to desired compaction and smoothness and assure proper sealing of joints hours Total hours 18

19 ROLLER, STEEL WHEEL (Other-Flatwheel or Tamping) Code 917 B. Observation of machine in operation hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Roll base course to desired compaction hours C. Roll asphalt surfaces to desired compaction and smoothness and assure proper sealing of joints hours Total hours 19

20 ROLLER, PNEUMATIC (Self-Propelled) Code 918 B. Observation of machine in operation hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Roll base course to desired compaction hours C. Roll asphalt surfaces to desired compaction and smoothness and assure proper sealing of joints hours Total hours 20

21 SCRAPERS (Over 17 C.Y.) Code 919 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Loading hours C. Spreading material hours D. Rough roadway grading hours E. Compaction of embankment hours Total hours 21

22 TRACTOR OPERATOR (80 H.P. and less) Code 920 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Pulling compaction implements hours C. Pull graders for dressing operations hours D. Ground clearing assistance hours Total hours 22

23 TRACTOR OPERATOR (Over 80 H.P.) Code 921 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Pushing other equipment to aid in loading or unloading operations hours C. Pulling compaction and mixing implements hours D. Ground clearing assistance hours Total hours 23

24 TRENCHING MACHINE, HEAVY Code 922 A. Safety procedures hours B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours A. Safety procedures hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures hours B. Excavation for footing and removal of unsuitable materials hours C. Trenching for pipe, etc hours Total hours 24

25 REINFORCING STEEL SETTER (Structures) Code 923 B. Observation of steel being set and welding of rods hours B. Steel bar placement hours III. Actual Steel Setting A. Rod fastening hours B. Rod cutting hours C. Rod welding hours D. Rod placement hours E. Fabrication of reinforcement assembly hours Total hours 25

26 STEEL WORKER (Structural) Code 924 B. Observation of steel worker hours B. Tool Review... 5 hours III. Operating with Steel Workers A. Raise and place fabricated structural steel hours B. Emphasis on girders, plates and columns hours C. Fasten steel members together by welding or bolting hours D. Signal erection crane, rig equipment hours Total hours 26

27 FOUNDATION DRILL OPERATOR Code 925 A. Orientation and observation... 5 hours B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Small hole drilling hours C. Large hole drilling hours D. Casing operation hours E. General operating hours Total hours 27

28 MECHANIC Code 926 A. Safety procedures hours B. Cleaning, disassembling and inspection of engine parts hours C. Installation and adjustment of minor parts hours A. Safety procedures hours B. Engine reconditioning hours C. Clutch installation hours D. Transmission reconditioning hours A. Safe operating procedures hours B. Electrical systems hours C. Hydraulic systems hours D. Final drive and track assemblies hours E. Welding and fabrication hours F. General field maintenance hours Total hours 28

29 WELDER Code 927 B. Welding equipment hours C. Materials selection hours D. Observation of welder hours II. Applied Techniques of Welding B. Acetylene-cutting, brazing and welding hours C. Electric-cutting and welding hours III. Actual Welding Operations B. Cut, lay out, fit and weld sheet metal, cast iron and other metal parts hours C. Fabricate and repair equipment hours Total hours 29

30 CRUSHER OR SCREENING PLANT OPERATOR - Code 928 B. Observation of machine in operation hours C. Starting of crusher operating conveyors hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Operation of conveyors and crusher operations hours C. Operation of crusher hours Total hours 30

31 TRUCK DRIVER Code 929 A. Safety procedures hours B. Observation (as a passenger) of vehicle in operation hours C. Starting and manipulating vehicle hours A. Safety procedures hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures hours B. Loading and unloading materials and operation of vehicle hours Total hours 31

32 ASPHALT DISTRIBUTOR Code 930 A. Safety procedures hours B. Observation of vehicle in operation hours C. Starting and manipulating valves and levers to distribute material and move equipment hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Regulates valves and levers to distribute oil or bituminous liquid for highway surfacing hours C. Operation of equipment hours Total hours 32

33 ASPHALT RAKER Code 931 B. Observation of placement of materials... 5 hours C. Perform duties of asphalt shoveler hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Adjustment of screed to regulate width and depth of material hours C. Distribution of material hours Total hours 33

34 BLASTER Code 932 B. Observation of work of Powder man hours C. Assist Powder man by carrying explosives, placing in holes, connecting lead wires hours II. Applied Techniques of Powder man A. Safety procedures hours B. Storage, transporting, placing and discharging of explosives hours III. Actual Blasting Operations A. Safe operating procedures hours B. Use of detonators and explosives hours C. Storage, movement and placing of explosives hours D. Placing wires, detonators and explosives, tamping and discharging hours Total hours 34

35 SPREADERBOX PERSON Code 933 B. Observation of machine in operation hours C. Starting, stopping and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Selection and loading of materials hours B. Spreading of stone or other granular materials on spread way sub-base or base hours Total hours 35

36 SIGN ERECTOR Code 934 I. Orientation and Safe Use of Tools and Equipment A. Power and hand tools hours B. Special fittings and hardware hours C. Specifications or design for concrete mixer hours II. Applied Techniques of Sign Erection A. Preparation of layout for signs hours B. Cuts, ties and sets reinforcing steel for footings hours C. Sets forms for, places concrete and sets anchor bolts hours D. Erects wood or metal structures hours E. Places clamps, brackets or other required hardware on structures hours III. Blueprint or Construction Plans Reading hours IV. Basic Design Familiarity V. Stripping and Salvage of Forms for Re-use hours Total hours 36

37 OILER Code 935 I. Orientation and Safe Use of Tools of the Trade A. Lubrication requirements of mechanical equipment hours B. Materials selection hours II. Applied Techniques of the Oiler B. Equipment characteristics and lubrication points hours C. Oil changes, filter changes, grease guns, hard packing of grease, greasing bearings hours D. Minor adjustments to drive chains and clutches hours III. Shop and Field Practices hours IV. Equipment Operation and Operation of Oil, Grease and Fuel Service Truck hours A. Safety procedures hours Total hours 37

38 UTILITY OPERATOR Code 936 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Operation of various equipment hours C. Special applications and functions hours Total hours 38

39 SERVICE PERSON - Code 937 A. Safety procedures hours B. Observing fueling, greasing and cleaning filters hours C. Fuel and grease used for different types of equipment hours II. Actual Operation A. Servicing all types of equipment hours B. Installation and adjustment of minor parts hours C. General field maintenance and operation of service truck hours Total hours 39

40 ELECTRICIAN Code 942 I. Orientation A. Safety procedures hours B. Basic rules of National Electrical Code hours C. Basic tools their care and uses hours II. Applied Techniques of Electrical Construction A. Wire ways types, uses and methods of installation hours B. Circuit wiring hours C. Protective equipment switches, panels, etc hours D. Feeders and services hours E. Lighting fixtures and wall outlets hours F. Control wiring hours G. Testing of completed work hours III. Technical Studies and Review A. Advance study of National Electrical Code hours B. Construction blueprints, reading and application hours IV. Underground Construction and Outside Lighting A. Underground conduit and wire hours B. Installation of outside lighting, maintenance and repairs hours V. Care and Maintenance of Trade Tools and Equipment hours Total hours 40

41 BATCHING PLANT SCALEPERSON Code 943 A. Safety Procedures... 5 hours B. Observation of equipment in operation hours C. Adjustment of scales, operation of controls and weighing hours B. Routine cleaning, lubrication and servicing hours A. Safe operating procedures hours B. Operating controls and scales for measurement and discharge of concrete or asphaltic materials into trucks, carriers or mixer hours Total hours 41

42 WAGON DRILL, BORING MACHINE OR POST HOLE DRILLER OPERATOR Code 944 A. Orientation and Observation... 5 hours B. General drilling procedures and operation hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Small hole drilling hours C. Large hole drilling hours D. Casing operation hours E. General operating hours Total hours 42

43 REINFORCING STEEL SETTER (Paving) Code 945 A. Safety Procedures... 5 hours B. Observation of steel being set hours B. Steel bar placement hours III. Actual Steel Setting A. Rod tying hours B. Rod cutting hours C. General rod placement hours Total hours 43

44 FORM SETTER (Paving) Code 946 B. Observation of setting grade line hours C. Observation of pulling, loading, hauling and placing forms hours B. Routine cleaning of forms and care of air and hand tools hours III. Actual Operation of Form Setting A. Safe operating procedures... 5 hours B. Set grade line hours C. Pull, load, haul and place forms hours D. Set forms to finish grade hours E. Drive pins hours F. Check alignment hours G. Spray forms hours H. Check forms while pouring concrete hours Total hours 44

45 SELF PROPELLED SWEEPER OPERATOR Code 947 B. Observation of machine in operation... 5 hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours Note: Point out necessity to wear eye protection while operating the sweeper B. Proper start-up, proper engagement and position of broom and proper sweeping technique hours C. Removal and replacement of broom wafers hours D. Operation of sweeper in cleaning of pavements hours Total hours 45

46 BULLDOZER, UNDER 150 H.P. - Code 948 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Movement and stockpiling of material hours C. Pushing and rough grading hours D. Clearing and grubbing hours E. Finish grading hours F. Special applications hours Total hours 46

47 SCRAPERS (Under 17 C.Y.) Code 949 B. Observation of machine in operation hours C. Starting and manipulating levers for moving equipment and attachments hours B. Routine fueling, lubricating and servicing hours A. Safe operating procedures... 5 hours B. Loading hours C. Spreading material hours D. Rough roadway grading hours E. Compaction of embankment hours Total hour 47