Cutter-/ suction dredger

Transcription

1 PARTICULARS : Type Compact cutter suction dredger, used demountable dredger Dimension 9 x 2.5 x 1,2 m Draft Approx. 0.9 m Air draft Control cabin approximately 2.5 m. A-frame approximately 3.5 m but can be modified to your requirements or equipped with an hydraulic adjustment system. Main engine GM type V871 with 180 kw at rpm Gearbox / Clutch Allison, reduction 4.2:1.0 Dredging pump Weir Minerals, Warman 10-8 installed 2015, current state 95% Cutter Vosta 5 blade with demountable teeth Dredging depth Up to 10 m Pipelines Suction 350 mm, pressure 250 mm Others Gland water dredging pump via main engine Hydraulic pump for hydraulic system via main engine 24 V electricity via alternator on main engine with a transformer to 220 V Separate generator on deck, Europower EP200DX1E 6 kva installed 2014

2 DESCRIPTION : The dredger consists of a main pontoon and two side pontoons. Attached to the two side pontoons on both sides are tubular floats for added stability and buoyancy. Both main and side pontoons are made of steel and strengthened with beams and stringers which are welded through. In the front compartment of the pontoon there are two heavy attachment points for the ladder and suction pipe and the entrance of the strengthened rubber suction hose. The main pontoon has a higher front deck after which a steel control cabin is placed with a removal top part which means narrow passages under bridges etc. can be easily achieved. The remaining part of the main pontoon concerns the engine/pump room containing at the aft side a fixed diesel tank of approximately 600 litres. In the basic cabin all required control units for operating the dredger are available. A dredging ladder for suction operation and/or cuttersuction operation is available. The cutter ladder has a 5 bladed VOSTA cutter with demountable cutter teeth on each blade. The cutter shaft is laid in a rubber bearing bushing and driven by a planetary gearbox by a hydraulic engine. In front of the operating cabin are placed on a frame 4 hydraulic winches for the PS- and SB side wire, the Front wire and the Ladder wire. On the front edge of the main pontoon are two heavy connection eyes for the A-frame of the ladder. This A-frame is constructed of steel en connected with two steel wires to heavy connection points on the deck housing. On the top of the deck housing there is one small and one large hatch and on SB side an entrance to the engine / pump room. On the P side the steel pumping line is coming up and lead to the back of the dredger where it can be connected to a rubber hose for connection to the floating line. On the P side aft of the dredger are two heavy guidance rollers in case and Aft wire is required. On top of the deck housing is a large exhaust muffler.the side pontoons are demountable and connected to the main pontoon by means of two bottom hooks and two top bolted plates. The deck of the side pontoons each have 2 boulders and lifting eyes. In the engine room the dredging pump and the main engine are placed amidships. SB side aft is an hydraulic oil tank. In the middle aft two large water intake and water filters going through the bottom hull for suctioning up the required cooling water. The engine is cooled directly. P side aft there are two start and light batteries together with some storage cabins and a small workbench. The dredger is compact, easy to transport and capable of a wide range of activities like maintenance dredging, sand winning and gravel winning. By means of the extensive renovation a KISS (keep it simple sir) type modern dredger is created by the former owner which means it will do the same productions as a brandnew dredger of this size. The whole dredger can be transported with two or three trucks depending on their size.

3 Pricing Used cutter suction dredger, as is where is, excluding VAT and ex-works, The Netherlands 1x Complete dredger as described above in this offer; Transport cost from the Netherlands to your required location excluding VAT Our Terms, Conditions and Warranties Conditions - Dredger is sold as is where is. - Dredger is immediately available for your inspection in the Netherlands - Offer valid 12 weeks after offer date. All previous offers in relation to this product a/o project by Eureka Dredgers bv are thus deemed non valid. - All pricing is in Euro, and excluding VAT. - Delivery ex works Eureka Dredgers bv, Ulft the Netherlands. - All our quotations, all orders placed with us and all contracts concluded with us, are subject to the METAALUNIE CONDITIONS 2014 (NL). These conditions are filed with the registrar of the District Court of Rotterdam. Eureka Dredgers bv is not liable for any cost and loss of income relating to interruption, standstill and or start-up of a (partial) company or plant. Payment terms 100% of total nett sum direct upon your order

4 Pictures of 2014 renovation

5

6

7 RELATED PRODUCTS: Metal Zodiak Sand separation plant Work pontoons Conveyers Maasstraat 3 NL-7071 VR ULFT The Netherlands Phone : 0 (031) Fax : 0 ( 031) info@eureka-bv.com All our quotations, all orders placed with us and all contracts concluded with us, are subject to the METAALUNIE CONDITIONS, as they read according to the text printed on the back. These conditions are filed with the registrar of the District Court of Rotterdam. Upon request, the conditions of delivery and payment will be sent to you for free as well. Ver: