STATE OF MINNESOTA PRICING PAGES (Typed responses required)

Transcription

1 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 1 of 2 Vendor Name: RDO Equipment Company Contact Person: Mike Kluck & Jesse Miller Street Address: DuPont Avenue South P.O. Box: City, State, Zip Burnsville, Minnesota Phone #: Mike: (952) or Jesse: (612) Toll Free #: (800) Fax #: (952) Address: mkluck@rdoequipment.com or jmiller@rdoequipment.com Website: Version of Excel used: Furnish separate price quote for each MOTOR GRADER being offered MOTOR GRADER Make & Model Normal/Variable HP Operating Weight Work lights John Deere 670G Gear 1 (160 hp) Gear 2 (165 hp) Gear 3 (175 hp) Gear 4 (190 hp) Gear 5 (190 hp) Gear 6 (195 hp) Gear 7 (195 hp) Gear 8 (195 hp) 35,220 Lbs 2 High and 2 Low Beam Halogen Headlights w/led Turn Signals on Bar, LED Rear Turn Signals Mounted on Rear Grill, Front and Rear LED Marker Lights, LED Brake Lights, and LED Hazard Warning Lights Blade Width 12 Ft Base Width (8 options available) Blade Height 24" Base Height, up to 27 " w/alternative options Blade Thickness 7/8" Base Thickness, and up to 1" w/alternative options Cutting Edge Size 6" x 5/8" Base, and up to 8" x 3/4" w/alternative options Circle drive slip clutch Optional Numbers of Drive Tires 4 Alternator Size 100 Amp Battery CCA (2) Group 4D Batteries 1400 CCA, 440 reserve minutes each. Seat type Fabric Air Suspension Seat with Armrests and Headrest 3 In., (76 mm) Seat Belt w/retractors (Conforms to SAE J386) Differential type Fuel Tank Size Rims, Size in Inches/Type Tires Block Heater, Watts Starting Aid Spiral Bevel, Hydraulically Actuated, Clutch Type can be Applied on-the-go, Selectable Manual or Automatic Differential Lock 111 Gallon 10 x 24 Inch Single Piece Rims 14.00x24 12PR Titan (G2) Bias Ply 120 Volt, 1500 Watts Ether Starting Aid

2 SEQ. # MOTOR GRADERS (5) Transmission, Speeds PRICING PAGES (Typed responses required) John Deere Powershift Plus, Direct Drive, Countershaft Powershift, Event Based Shifting (EBS) - Load Sensing Electronic Shift Modulation, Over speed Protection Quick Disconnect Pressure Ports Matched 8 Forward and 8 Reverse Speeds, Industry Standard U-Shape Shift Pattern, Transmission Neutral Lock with Park Start Safety Switch, Rubber Isolation Mounting to Reduce Noise and Vibration, Independent Oil Reservoir, Filtration and Cooling System with: * 31 GPM Transmission Hydraulic Gear Pump, 2000 Hour Vertical Spin- On Filter Shift Lever Position 1 (2.5 mph) Shift Lever Position 2 (3.5 mph) Shift Lever Position 3 (4.8 mph) Shift Lever Position 4 (6.8 mph) Page 2 of 2 Shift Lever Position 5 (10.2 mph) Shift Lever Position 6 (14.4 mph) Shift Lever Position 7 (20.1 mph) Shift Lever Position 8 (28.3 mph) Forward/Reverse 8 Forward / 8 Reverse (2.5 mph to 28.3 mph) Auto Shift/Manual/Power shift Optional Auto Shift/Manual N/A/Power Shift Standard Heater BTU 31,500 BTU (A/C Standard) Window openings (2) Doors and (2) Left and (2) Right. Front lower and rear sides. Hydraulics Closed-center, pressurecompensated load-sensing (PCLS), variable-displacement piston pump, O-ring face-seal fi ttings Maximum Pump Flow 212 L/min. (56 gpm) Maximum System Pressure kpa (2,750 psi) Pump Displacement 90 cm3 (5.5 cu. in.) Cab Profile/Height Low Profile ROPS Cab, 10' 5" to top of cab Warranty 1 Year Full Machine Warranty BASE PRICE $ 171, John Deere 670G Motor Grader 1.1 BASE MACHINE as stated above. "Included" denotes included in $ 171, BASE PRICE G Grader w/standard Hydraulic Controls GP Grader w/grade Pro EH Controls (Includes finger tip $ 18, controls w/industry standard control pattern, cross slope, Topcon and Trimble ready, return to straight, lever steering and conventional steering wheel) 1.3 Transportation to Monroe Snow & Ice Equipment for Attachment $ 1, Installation 1.4 Transportation to Little Falls Machine, Inc. for Attachment Installation $

3 Qty Price 2.0 OPERATOR STATION Offer operator station options. Number the items starting with 2.1, 2.2, etc., 2.01 Air Conditioning 2.02 Cab Rear Window Electric Defroster Low Cab w/ Fixed Lower Front & Side Windows Low cab w/fixed lower front and side opening windows $ Low Cab w/ Lower Front & Side Opening Windows (Includes roof wiring harness for lighting, beacon, precleaner, and heated mirrors) $ Tall Cab w/ Lower Fixed Front & Side Opening Windows $ Grade Pro Low Cab w/lower Front and Side Opening Windows (Requires 1.2 and 2.12) In Configuration Powered Cab Air Precleaner $ Cab w/o Precleaner Standard Fabric Air Suspension Seat w/armrests and Headrest Premium Heated, Leather/Fabric, High-Wide Back, Air Suspension Seat with Armrests. For use with cab codes 2.03, 2.04, 2.05 & This seat does not include a headrest. $ Grade Pro Premium Heated, Leather/Fabric, High-Wide Back Air Suspension Seat (Requires 1.2 and 2.07) In Configuration to-12 Volt Converter (15 amps) to-12 Volt Converter (30 amps) $ Exterior Mounted Rearview Mirrors Heated Exterior Mounted Rearview Mirrors $ Lower Front Intermittent Wiper & Washer $ Less Lower Front window Wiper & Washer AM/FM Radio with CD and Weather Band (WB) $ No Radio Rear Camera (Provides rear view from dash monitor) $ 1, No Rear Camera Front Window Movable Sun Visor $ Rear Retractable Sun Shade $ Decelerator $ lbs. multi purpose (ABC) Dry Chemical Fire Extinguisher $ Secondary Steering $ 1, ENGINE/POWER TRAIN Offer engine and powertrain options. Number starting with 3.1, 3.2, etc Cool-On-Demand Automatic Reversing Hydraulic Fan 3.02 Fluid Sampling Ports (For sampling engine oil, engine coolant, hydraulic oil, axle & transmission fluids) John Deere PowerTech PSX 9.0L meets EPA IT4 / EU Stage IIIB Emissions (195 Net Peak hp) Standard 100 Amp Alternator amp Alternator $ amp Alternator $ Quick Service Bank for Fluid Changes for Transmission, Hydraulic, Engine Oil, and Engine Coolant (Remote service bank is inside engine compartment and includes Industry Standard Quick Disconnect Couplers) $ No Quick Service Group Standard Fuel & Water Filtration Severe Duty Fuel & Water Filtration System $ Fast Fill Fuel System (150 gpm fill rate) $ 1, No Fast Fill Fuel System Hydraulic Pump Disconnect for Cold Weather Starting $ No Hydraulic Pump Disconnect Engine Exhaust with Flat Black Stack for 9.0L (EPA IT4/EU Stage IIIB only) Engine Exhaust with Chrome Stack for 9.0L (EPA IT4/EU Stage IIIB only) $ Autoshift Transmission $ Manual Shift (No Autoshift) Transmission Transmission Solenoid Valve Guard $ No Transmission Solenoid Valve Group Engine Coolant Circulating Heater, 120 Volt, 1500 Watt Included Ether Starting Aid Included Cold Weather Control Valve Covers (Plastic covers that mount below the cab, shielding the control valve from snow and slowing down hydraulic heat loss in winter. Requires 1.2) $ ELECTRICAL/LIGHTS Offer electrical/light options. Number starting with 4.1, 4.2, etc AT Beacon Strobe kitinstalled $ Volt to 12 Volt, 15 Amp Converter w/two outlets 4.03 JDLink Ultimate Machine Monitoring System with 3 Year Message Service Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport Lights) (Includes 2 high and 2 low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grill, front and rear LED marker lights, LED brake lights, and LED hazard warning lights) GRADING LIGHTS (10 HALOGEN LIGHTS) Includes code 4.01 Transporting Halogen w/ LED Signal and Marker Lights, plus (6) Work lights: (2) on bottom of cab, (2) on midframe, and (2) reversing lights on rear grill. $ DELUXE GRADING LIGHTS (16 HALOGEN LIGHTS) NOTE: * Includes code 4.05 Grading Lights plus (6) additional work lights: (4) Corner Cab Work Lights and (2) Front Cab Work Lights.* Requires code amp Altenator or amp Altenator (IT4). $ DELUXE GRADING LIGHTS w/ 2 additional RH Cab Roof Lights (18 HALOGEN LIGHTS) NOTE:* Requires alternator code 3.05 or * Includes code 4.06 Deluxe Grading Lights w/ LED Colored Lights and (2) Additional Rightside Work Lights. $ Two Batteries, Group 4D (1000 CCA, 180 reserve minutes each) $ (47) Two Batteries, Group 4D (1400 CCA, 440 Reserve Minutes Each) Level 1 Electronic Corrosion Prevention Package (Requires 3.19) $ Tall Front Snow Plow Light Bar 26" higher than Standard Frame Lights. Not for use with Mid Mount Scarifier $ Flip Down Cab Beacon Bracket (RH) For Single Beacon on Cab. $ Flip Down Cab Beacon Bracket (LH) $ TIRES/RIMS

4 Offer tire/rim options Number starting with 5.1, 5.2, etc Less Tires & Wheels (NOTE: NOT AVAILABLE FOR UNIT 3R & 48) $ (4,319) x24 12PR SGG Firestone (G2) Bias Tires w/1 pc. Rim $ 2, x24 12 PR Titan G2 Bias Tires w/1pc. Rim In. 12 PR SGG Firestone G2 Bias Tires w/ 3 pc. Rims $ 3, In. 12 PR Titan G2 Bias Tires w/ 3 pc. Rims $ R 24 Inch G2/L2 Single Star XGLA2 Michelin Radial Tires w/ 1 pc. Rims $ 5, R 24 Inch G2/L2 Single Star VUT Bridgestone Radial Tires w/ 1 pc. Rims $ 4, R 24 Inch G2/L2 Single Star XGLA2 Michelin Radial Tires w/ 3 pc. Rims $ 6, R 24 Inch G2/L2 Single Star VUT Bridgestone Radial Tires w/ 3 pc. Rims $ 5, R 24 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 1 pc. Rims $ 7, In. 12 PR G2/L2 SGG Firestone Bias Tires w/ 1 pc. Rims $ 3, X25 12 ply L2 Goodyear Radial Tires on 1 pc. Rims $ 4, In. 12 PR G2/L2 SGG Firestone Bias Tires w/ 3 pc. Rims $ 4, X25 12 ply L2 Goodyear Tires on 3 pc. Rims $ 6, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 1 pc. Rims $ 6, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 1pc. Rims $ 6, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 1 pc. Rims $ 3, R25 L3 Goodyear Radial Tires on 1 pc. Rims $ 13, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 3 pc. Rims $ 8, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 3pc. Rims $ 7, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 3 pc. Rims $ 4, R25 L3 Goodyear Radial Tires on 3 pc. Rims $ 18, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 1 pc. Rims $ 8, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 3 pc. Rims $ 9, R 25 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 1 pc. Rims $ 8, R 25 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 1 pc. Rims $ 7, R25 Goodyear Snow Tires on 1 pc. Rims $ 11, Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 1 pc. Rim $ 3, Front Fenders $ No Front Fenders Rear Wheel Fenders in.(476mm) Rear Wheel Fenders Fenders are not for use with 550 tires. Fenders can only be used with chains that are designed for 3" of radial clearance and 1.75" of sidewall clearance. Use of Tire chains permitted in accordance with SAE J683, and requires removal of front mud flap on rear fenders. $ 1, HYDRAULICS Offer hydraulic options. Number starting with 6.1, 6.2, etc. Right Hand - Standard Hydraulic Controls Base Hydraulics - 4 Function Controls Requires code 1.1. Base Functions: Rear Steer, Circle Side shift, Wheel Lean & RH Blade Lift w/ Float Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base functions plus 1 function w/float control - front plumbing and hoses for Scarifier or auxiliary applicaton. For Use with Front Scarifier. $ Mid Mount Scarifier Base Hydraulics w/ 1 Auxiliary Function Control Requires Mid Mount Scarifier code and 1.1. Midmount scarifier base hydraulics with 1 auxilliary function control with float control for mid mount scarifier. For use with mid mount scarifier. $ Base Hydraulics w/2 Auxiliary Function Controls Requires code 1.1. Base functions plus 2 functions w/float control - front plumbing and hoses for Scarifier and/or auxiliary application.for Use with Front Scarifier. $ 1, Base Hydraulics w/ 3 Auxiliary Function Controls Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o float control, front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ 2,098 Right Hand - GRADE PRO CONTROLS Finger-tip armrest mounted controls, consistent with the industry standard pattern. Includes armrest mounted lever steering plus the traditional steering wheel. All Auxiliary codes include front and rear plumbing for each Auxiliary function Grade Pro Controls for Mid Mount Scarifier w/1 Auxiliary Function Control Requires codes 1.2 and Mid Mount Scarifier code $ Grade Pro Controls with Base Functions NOTE: * Requires code 1.2. * Grade Pro Base Hydraulics Functions: Rear Steer, Circle Side shift, Wheel Lean, Right and Left hand Blade Lift w/ Float, Circle Rotate, Blade Side Shift, Blade Tilt, Lever Steering (also includes steering wheel) In Configuration Grade Pro Controls w/1 Rear Auxiliary Function and Left Hand Lever Controller Requires code 1.2. Base functions plus 1 auxiliary function w/float control - Rear plumbing and hoses for Ripper or auxiliary applicaton. For Use with Rear Ripper. $ Grade Pro Controls w/1 Front Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 FRONT auxiliary function w/float control - front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ Grade Pro Controls w/1 Rear Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 REAR auxiliary function w/float control - front plumbing and hoses for auxiliary application. $ Grade Pro Controls w/1 Front Auxiliary Function and 2 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 3 auxiliary functions- 1 front and 2 rear auxiliary functions w/ float control and rear plumbing for Scarifier / Ripper and/or front, mid $ 2, Grade Pro Controls w/1 Front, 1 Rear Auxiliary Function Control with Right and Left hand Controllers Requires code 1.2. Base Functions plus 2 auxiliary functions - 1 front and 1 rear with float control and plumbing Scarifier / Ripper applications. Auxiliary functions have reconfigurable controls. $ 1, Grade Pro Controls w/1 Front Auxiliary Function and 3 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 4 auxiliary functions - 1 front and 3 rear with float control and plumbing for Scarifier/Ripper and/or front, mid and rear auxiliary applications. Auxiliary functions have reconfigurable controls. $ 3, Grade Pro Controls w/3 Front and 3 Rear Auxiliary Function Controls with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 6 auxiliary functions-3 front and 3 rear with float control on 4 functions, and includes front and rear plumbing for 2 Functions each. Auxiliary functions have reconfigurable controls. $ 4,540 Left Hand - Standard hydraulic Controls Base Hydraulics- 4 Function Controls Requires code 1.1. Base Functions: LH Blade Lift w/ Float, Blade Side shift, Circle Rotate, Blade Tilt Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base Functions plus 1 function w/float control and lines for Ripper or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 665

5 Base Hydraulics w/2 Auxiliary Function Control Requires code 1.1. Base functions plus 2 functions w/float control and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 1, Base Hydraulics w/ 3 Auxiliary Function Control Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o Float Control, and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 2, Grade Pro Controls - Left Side NOTE: * Requires code 1.2. * Accompanies GRADE PRO CONTROLS - RIGHT SIDE order code selection. In Configuration Oil, SAE 10W AW46 All Season Hydraulic Oil $ Hydraulic Oil, ISO 46 $ MOLDBOARD/CUTTING EDGE/END BITS/CIRCLE DRIVE Offer these options starting with 7.1, 7.2, 7.3, etc Blade Impact Absorption System Protects Moldboard and draft frame from impacts with Stationary objects $ 1, No Blade Impact Absorption system Ft. x 24 In. x 7/8 In. (3.66 M x 610 mm x 22 mm) with 6 In. x 5/8 In. (152 x 16 mm) Cutting Edge and 5/8 in. (16mm) Hardware Ft. x 24 In. x 7/8 In. (3.66 M x 610 mm x 22 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (3.66 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (3.96 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 24 In. x 7/8 In. (4.27 M x 610 mm x 22 mm) with 6 In. x 5/8 In. (152 x 16 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 24 In. x 7/8 In. (4.27 M x 610 mm x 22 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edgeand 5/8 in. (16mm) Hardware NOTE: Requires engine code $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 3/4 in. (19mm) Hardware Requires engine code $ Extended Life Bronze Wear Inserts NOTE: Recommended for applications in abrasive material. $ Wear Inserts w/o Clutch (Recommended for higher circle torque) Nylon Wear Inserts w/clutch Requires code 7.19 Circle Drive Slip Clutch. Recommended for higher circle torque when used with a slip clutch. $ Reversible Overlay End Bits Not avaible for unit 3R & 48. $ No Reversible Overlay End Bits No Moldboard Extension " 24 in. Left Hand Moldboard Extension Requires Moldboard code 7.08,7.09, or Not available for units 3R & 48. $ 1, " 24 in. Right Hand Moldboard Extension NOTE: * Requires Moldboard code 7.08,7.09, or * Available to all other units with no restrictions. $ 1, Circle Drive with Slip Clutch Protects circle, circle drive gearbox and draft frame from damage when end of moldboard comes in contact with stationary objects. Slip clutch is integral to the circle drive assembly and utilizes a wet clutch system. Can not be used with code 7.04 inserts. $ 1, AT Moldboard Extension, 24 X 24 X 7/8 In. Left Hand 7/8 in. (22mm) thick. Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 24 x 24 x 7/8 In. Right Hand 7/8 in. (22mm) thick. Requires 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 2, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 1, FRONT ATTACHMENTS Offer front attachment options. Starting with 8.1, 8.2, etc. *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & Additional Charges Front Push Block $ 1, Front Scarifier Includes Front Hydraulics, plumbing and hoses Scarifier with 2 pitch positions and 9 shank pockets Five 1 x 3 inch Scarifier Shanks w/teeth If additional shanks are desired order (1) each of T6Y5230 Tooth, T Shank and T Retainer for each set. Can not be used with 6.07 Hydraulics. $ 4, Mid-Mount Scarifier with Integrated Front Push Plate NOTE: * Requires code 6.03 or 6.06 Hydraulics. * Mid-Mount Scarifier with Push Block Can not be used with Front Scarifier. * Not for use with Front Fenders Code * Recommend Rear Counterweight for better machine balance. $ 6, Balderson Style Front Lift Group NOTE: * Requires Hydraulic code 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13, or * (2) AT Mating Hooks from Parts are available to convert old front attachments to the Bladerson-style lift group. $ 3, Less Front Attachment Front-Mounted Dozer Blade, 97 in. x 37.6 in. (2464 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or Requires one of the following 14.0 x 24 tire codes: 5.01, 5.02, 5.03, 5.04, 5.05, 5.06, 5.07, 5.08, or $ 4, Front-Mounted Dozer Blade, 105 in. x 37.6 in. (2667 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires one of the following 17.5 x 25 tire codes: 5.01, 5.11, 5.13, 5.15, 5.16, 5.17, 5.19, 5.20, 5.21, 5.23, 5.24, 5.25, 5.26 $ 4,575 FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Front Hitch Systems - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Standard Hitch System (Pin-on style hitch. 3.5 double acting lift cylinder with 2 rod.) $ 2, Falls Modified 29" Husting Hitch System (Drive -in quick coupler with vertical lift. 3.5 double acting lift cylinder with 2 rod.) $ 3, Falls Modified 34" Husting Hitch System $ 4, Para-Lift Model PLS-1 Hitch System (Drive-in parallel lift quick coupler. $ 3,987

6 Front Hitch System Options Hydraulic Locking Pin Assembly for Para-Lift Hitch $ Factory Installation of Hydraulic Locking Pin Assy for Para-Lift Hitch $ One Pair Attachment Hooks, Flat Back for Para-Lift Hitch (*Not installed) $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 One Way Snow-Plows Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge, 9'10" Clearing Width w/ Standard Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 29" Husting Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 34" Husting Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Para-Lift Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Scar-a-Lift or Deere Front Mounted Scarifier Coupler $ 8,110 One Way Snow Plow Options Carbide cutting edge, three (3) pc., 3/4 x 6, per foot $112/ft Rubber belt deflector, 3/8 x 12 $ Heavy duty Spring Trip Tilt Bars, add $ Heavy duty Trip Edge Assembly, add $ 1, Hydraulic Moldboard Tilt, replaces rigid or spring trip bars, add $ Steel caster wheel assemblies, add $ 1, Pneumatic caster wheel assemblies, add $ 1, Left hand discharge, add $ Snow Wheel System, add $ 2,023 V-Type Snow Plows - Select the Hitch Attachment Coupler from the Options Falls V-890, 10 gauge A steel moldboard, 10 8 overall width, 9 8 clearing width, 48 nose height, 72 discharge height, three (3) screw-adjustable skid shoes (no tools required), spring loaded snow deflectors $ 6, Falls V-90, 7 gauge A steel moldboard, 12 0 overall width, 9 8 clearing width, 60 nose height, 84 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 6, Falls V-100, 7 gauge A steel moldboard, 13 3 overall width, 10 4 clearing width, 66 nose height, 92 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 8,342 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System $ 1, Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 2, Plow Unit to fit Falls Para-Lift Hitch System w/oscillating feature $ 1, Plow Unit to fit Falls Para-Lift Hitch System (hooks welded solid) $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,360 V-Type Snow Plow Options Spring Loaded Steel Snow Deflectors (Standard on the Falls V-890) $ Rubber Belt Snow Deflector (3/8" x 12") $ Down Pressure Kit for Standard and Modified Husting Hitch Systems $ Snow-Wheel System (In lieu of standard shoes) $ 4,228 Heavy Duty Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options Falls HDR-11, 11' Cutting Edge, 48" High (*Select Hitch from Options) $ 8, Falls HDR-12, 12' Cutting Edge, 48" High (*Select Hitch from Options) $ 8,958 Hitch Attachment Couplers Plow Unit to fit Falls Para-Lift Hitch System $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2, Optional Oscillation Plate (allows plow to follow road contour) $ 1,545 Heavy Duty Reversible Snow Plow Options Carbide Cutting Edge, Add per foot $112//ft Rubber Belt Snow Deflector (3/8" x 12") $ Moldboard Shoes (*Standard Equipment - Not available w/ trip edge assembly) No Charge Screw Adjustable Mushroom Shoes - Set of Two (Can be used with trip edge assembly) $ Trip Edge Assembly (One-piece construction) $ 1,709 Power Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options PR1143 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 6, PR1243 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 7, PR1155/PR1255 Raise moldboard height on PR1143 or PR1243, add to respective snow plow $ TER-11 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6, TER-12 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6,884 Plow-Hitch System Attachment Provides Full Oscillation Left and Right Plow Unit to fit Falls Standard Hitch System $ Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 1, Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,032 Power Reversible Snow Plow Options Trip Edge Assembly $ 1, Carbide Cutting Edge Per Foot $112/ft Rubber Belt Snow Deflector, 3/8" x 12" $ Steel Caster Wheel Assemblies $ 1, Pneumatic Caster Wheel Assemblies $ 1, Curb Shoe, Cylindrical, Each $ Curb Shoe, Wrap-Around, Each $ Snow-Wheel System (In lieu of standard shoes) $ 2,729 Dozer Blades - Select the Hitch Attachment Coupler from the Options Falls D3696, 8 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36108, 9 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4,415

7 8.090 Falls D36120, 10 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4,620 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System No Charge Plow Unit to fit Falls Modified 29" Husting Hitch System No Charge Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 1,923 Dozer Blade Options Carbide Cutting Edge, Per Foot $112/ft Scar-A-Lift - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Model FMS-1 Front Mounted Scarifier $ 5,199 Scar-A-Lift Options Scarifier, Head Only, 5 Teeth, No Head Plate or Arms $ 2, Scarifier, Head Only, 5 Teeth, Para-Lift Hooks Installed $ 3, Scarifier Shank, End Bit and Retainer (Each) $ Para-Lift Attachment Hooks, Flat Back, Per Pair $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 HENKE SNOW ATTACHMENTS Henke Fixed Position Dozer Blades DB8 8' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB9 9' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB10 10' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5,348 Lift Group (JRB Installation of Lift Group, Including Freight from Leavenworth STB-STD Scarifier Tool Bar - Lift Group (*Requires hoses to the nose of the motor grader) $ 4, PLG-STD Parallel Lift Group (*Requires hoses to the nose of the motor grader) $ 3, AQC Automatic Quick Coupler Lift Group (*Requires hoses to the nose of the motor grader) $ 5, HSH Henke Universal Hitch for Grader $ 2,596 Attachment Adapter PSS Plow Scarifier Sockets - Mounts to Henke or Factory Scarifier (Specify) $ PLH Parallel Lift Hooks - Mounts to Henke or field "Balderson Style" Lift Group $ AQC Female Attaching Adapter $ 1,367 Henke REL - Heavy Duty Reversible Snow Plow REL 10 10' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 12 12' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 14 14' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 12, REL 16 16' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 13,957 Henke SDDB - Severe Duty Dozer Blade SDDB 10 10' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 12 12' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 14 14' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12, SDDB 16 16' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12,356 Henke HH - Henke Helper Utility Blade HH 8 8' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 9 9' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 10 10' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 8,067 Henke FV - Multi-Directional Folding Vee Snowplow (MDFVS) FV 12 12' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 14, FV 14 14' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 15, FV 16 16' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS ) $ 16,622 Henke Tube Table Power Reversible Snow Plows (Include Grader Adaptor) R11TT 50" Tall, Power Reversible Trip Plow w/tube Table Reversing Frame $ 7, R12TT 50" Tall, Power Reversible Trip Plow w/tube Reversing Frame $ 8,095 Henke Plow Options Mushroom Shoes - Pair $ Install Dealer Supplied Coupler $ Parallel Lift Hook Coupler-Supply/Install $ JRB Style Coupler (Verify size and type) $ Hydraulic Hi-Gate for REL (Includes diverter Kit) $ 6, Trip Lockout Option $ ACS Coupler-Supply/Install $ 1,595 Henke V-Plow V-9.5 Vee Plow 9.5 Foot Cutting Swath $ 6, V-10 Vee Plow 10 Foot Cutting Swath $ 7,602

8 9.0 REAR ATTACHMENTS Offer rear attachment options. Starting with 9.1, 9.2, etc No Rear Attachment Rear Mounted Ripper/Scarifier Combination with Rear Hitch and Pin Includes Rear mounted Ripper/Scarifier with rear hitch and pin. NeverGrease Pin Joints. Three 2 x 5 in. Ripper Shanks w/teeth. Can not be used with codes 6.07, 6.09 or $ 8, Rear Counterweight with Rear Hitch and Pin 1600 lbs.(725.7 kg.) Rear Counterweight. Recommend for use with Front / Mid Scarifier. $ 1, Rear Hitch and Pin Not for use with Rear Ripper/Scarifier. $ (9) Extra Scarifier Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ (2) Extra Ripper Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ Slow Moving Vehicle (SMV) Sign Included Handi Hitch *Prices Do Not Include Mounting PP01G Handi Hitch Profile Packer/Roller 90" includes Lift Plate, 24" Packer Offset No Installation Included $ 18, HH01G 870GP Lift Assembly/Offset $ 3, PP04G Profile Accumulator and Hoses $ CR10 Handi Hitch Contour Packer/Roller 75" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR12 Handi Hitch Contour Packer/Roller 90" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR14 Handi Hitch Contour Packer/Roller 105" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 19, CR30 Contour/PP Ripper Shanks $ 1, WR30E Contour Ripper Shank Extender Plates $ CR40 Handi Hitch Contour 24" Packer Offset $ 2, CR50 Handi Hitch Contour Heavy Duty Lift Assembly $ 4, CR55 Handi Hitch Contour Accumulator and Hoses $ CR59 John Deere Link Arms (Lift Assembly) $ SIDE ATTACHMENTS Offer side attachment options. Starting with 10.1, 10.2, etc. FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Wings Falls W12 Wing Only, 12 ft. cutting edge moldboard, 36 height, hydraulic-over-cable controls, rear wing post height is manually adjustable. $ 11, Falls W-14 Wing Only, 14 ft. moldboard cutting edge. $ 12, Falls 2012A Wing Only, 12 ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys, rear wing post height is manually adjustable. $ 12, Falls 2012A Low Post (66" vs 100") $ 12, Falls 2014A Wing Only, 14 ft. moldboard cutting edge. $ 13,090 Invisible Mast Snow Wings (Mast Post Fits Under Cab for Maximum Visibility) IM ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys.invisible Mast post fits under cab allowing maximum visibility. $ 17, IM3014 Same as above w/14' Moldboard $ 17,510 Options for Falls Wings Hydraulic Extendable Buffer Brace $ 2, Hydraulic Elevating Rear Slide $ Trip Edge Assembly for 12 Foot Add $ 1, Trip Edge Assembly for 14 Foot Add $ 1, Left Hand Discharge Add $ Ripper Mount in Lieu of Rear Wing Post and Slide No charge HENKE SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included Price Includes Installation at Factory Wings AHW12FR 12' Grader Wing for Fixed Rear Applications (*Requires 2 valves) $ 11, AHW12MR 12' Grader Wing for Manual Adjusting Rear Applications (*Requires 2 valves) $ 11, AHW12RR 12' Grader Wing for Rear Ripper Applications (*Requires 2 valves) $ 10, AHW12ER 12' Grader Wing for Elevating (Benching) Applications (*Requires 3 valves) $ 12,328 Wing Options ' Grader Moldboard $ Trip Edge Option $ Hi-Gate - Hydraulic End Gate (Includes a diverter kit) $ 4, Factory Installation Wing installation by JRB at the John Deere Factory Included STB-STD Scarifier Tool Bar $ 3, PLG-STD Parallel Lift Group $ 3, AQC Automatic Lift Group $ 4, HSH Henke Standard Hitch (Truck style hitch modified for grader) $ 2, JRB Installation of Lift Group in Davenport Including Freight $ 547 Monroe SNOW ATTACHMENTS (ALL PRICES INCLUDE INSTALLATION AT MONROE) Wings AHW12E-62 for JD "G" Series, 12' All Hydraulic Wing Package w/ 62" Bench Height, 5/8" x 8" Cutting Edge $ 15, AHW12E-38 for JD "G" Series, 12' All Hydraulic Wing Package w/ 38" Bench Height, 5/8" x 8" Cutting Edge $ 15,305 Wing Options Deduct to delete rear post assembly and use ripper-mount bracketry in it's place $ (1,553) Deduct to delete rear post and use 2-position fixed post in it's place $ (1,015) ' Wing Moldboard in Lieu of Standard 12' Model (Requires and/or 10.28) $ Front Lift Group Installed on G-Series Grader $ 5, OTHER ATTACHMENTS Offer other attachment options. Number starting with 11.1, 11.2, etc NS Slopemeter #2 (Installed) $ AT IGC Mast Mounts $ 650 *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & Additional Charges EXTENDED WARRANTY OPTIONS Offer performance/warranty options. Number these starting with 12.1, 12.2, etc. (Specify years, miles or hours extended term covers.) Comprehensive (SEE PRICE MATRIX BELOW)

9 12.02 Power Train and Hydraulics (SEE PRICE MATRIX BELOW) Power Train (SEE PRICE MATRIX BELOW) Engine Only (SEE PRICE MATRIX BELOW) Warranty covers John Deere manufactured components only. Standard Manufacturers Warranty applies to all components that are not manufactured by John Deere Extended Powertrain and Hydraulic Warranty has no Deductible per Occurrence after Initial Warranty - See Attached Extended Warranty Sheet Preventative Maintenance Contract (3 Year/2000 Hour) Cost per Hour $ NEW EQUIPMENT RENTAL PROGRAM If rental programs are available on the new equipment offered, with the option to purchase, list the hourly/weekly/monthly rental rate. Indicate the percent of rental fee paid by the purchaser that will be applied to the purchase price. See Solicitation Special Terms & Conditions. Hourly Rental Rate: NA Weekly Rental Rate: $ 2,200 Monthly Rental Rate: $ 6,600 Percent (%) of Rental Fee applied to purchase price: 100% If the new rental equipment is purchased and finance charges are applicable for the actual rental term only, state the actual interest rate here: NA 14 VENDOR OWNED RENTAL RETURN OR DEMO EQUIPMENT PROGRAM See Solicitation Special Terms and Conditions. DEDUCT cost per Used Hour from the original Contract Price $ 25.00

10 15 DISCOUNT OFF LIST PRICE FOR RELATED PARTS & ACCESSORIES 0% (See Special Terms and Conditions) 16 DELIVERY STARTING POINT City, State, Zip Nearest RDO Equipment or Nortrax Facility RDO Equipment Burnsville, MN Grand Forks, ND Moorehead, MN Rochester, MN Marshal, MN N. Mankato, MN Sauk Rapids, MN Sioux Falls, SD NORTRAX Bemidji, MN Duluth, MN Grand Rapids, MN DELIVERY PRICE PER LOADED MILE No Flat Rate Allowed- See Special Terms and Conditions $6.00 w/$300 Minimum

11 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 1 of 2 Vendor Name: RDO Equipment Company Contact Person: Mike Kluck & Jesse Miller Street Address: DuPont Avenue South P.O. Box: City, State, Zip Burnsville, Minnesota Phone #: Mike: (952) or Jesse: (612) Toll Free #: (800) Fax #: (952) Address: mkluck@rdoequipment.com or jmiller@rdoequipment.com Website: Version of Excel used: Furnish separate price quote for each MOTOR GRADER being offered MOTOR GRADER Make & Model Normal/Variable HP Operating Weight Work lights John Deere 672G Gear 1 (6WD on) (175 hp) Gear 2 (6WD on) (180 hp) Gear 3 (6WD on) (185 hp) Gear 4 (6WD on) (190 hp) Gear 5 (190 hp) Gear 6 (195 hp) Gear 7 (195 hp) Gear 8 (195 hp) 37,470 Lbs 2 High and 2 Low Beam Halogen Headlights w/led Turn Signals on Bar, LED Rear Turn Signals Mounted on Rear Grill, Front and Rear LED Marker Lights, LED Brake Lights, and LED Hazard Warning Lights Blade Width 12 Ft Base Width (8 options available) Blade Height 24" Base Height, up to 27 " w/alternative options Blade Thickness 7/8" Base Thickness, and up to 1" w/alternative options Cutting Edge Size 6" x 5/8" Base, and up to 8" x 3/4" w/alternative options Circle drive slip clutch Optional Numbers of Drive Tires 6 Alternator Size 100 Amp Battery CCA (2) Group 4D Batteries 1400 CCA, 440 reserve minutes each. Seat type Fabric Air Suspension Seat with Armrests and Headrest 3 In., (76 mm) Seat Belt w/retractors (Conforms to SAE J386) Differential type Fuel Tank Size Rims, Size in Inches/Type Tires Block Heater, Watts Starting Aid Transmission, Speeds Spiral bevel; hydraulically actuated, clutch type can be applied on-the-go; selectable manual or automatic differential lock 111 Gallon 10 x 24 Inch Single Piece Rims In. 12 PR Titan G2 Bias Tires 120 Volt, 1500 Watts Ether Starting Aid Direct-drive John Deere PowerShift Plus, modulated shift-on-the-go, Event-Based Shifting (EBS), inching pedal; independent transmission reservoir with separate fi ltration and cooling system with 125-L/min. (33 gpm) gear pump. Maximum Travel Speeds With no tire slip at 2,180 rpm, 14.0-R24 tires

12 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 2 of 2 Shift Lever Position 1 (2.5 mph) Shift Lever Position 2 (3.5 mph) Shift Lever Position 3 (4.8 mph) Shift Lever Position 4 (6.8 mph) Shift Lever Position 5 (10.2 mph) Shift Lever Position 6 (14.4 mph) Shift Lever Position 7 (20.1 mph) Shift Lever Position 8 (28.3 mph) Forward/Reverse 8 Forward / 8 Reverse (2.5 mph to 28.3 mph) Auto Shift/Manual/Power shift Optional Auto Shift/Manual N/A/Power Shift Standard Heater BTU 31,500 BTU (A/C Standard) Window openings (2) Doors and (2) Left and (2) Right. Front lower and rear sides. Hydraulics Closed-center, pressurecompensated load-sensing (PCLS), variable-displacement piston pump, O-ring face-seal fi ttings Maximum Pump Flow 212 L/min. (56 gpm) Maximum System Pressure kpa (2,750 psi) Pump Displacement 90 cm3 (5.5 cu. in.) Cab Profile/Height Warranty Low Profile ROPS Cab, 10' 5" to top of cab 1 Year Full Machine Warranty BASE PRICE $ 180, John Deere 672G Motor Grader 1.1 BASE MACHINE as stated above. "Included" denotes included in $ 180, BASE PRICE G Grader w/standard Hydraulic Controls GP Grader w/grade Pro EH Controls (Includes finger tip $ 18, controls w/industry standard control pattern, cross slope, Topcon and Trimble ready, return to straight, lever steering and conventional steering wheel) 1.3 Transportation to Monroe Snow & Ice Equipment for Attachment $ 1, Installation 1.4 Transportation to Little Falls Machine, Inc. for Attachment Installation $

13 Qty Price 2.0 OPERATOR STATION Offer operator station options. Number the items starting with 2.1, 2.2, etc., 2.01 Air Conditioning 2.02 Cab Rear Window Electric Defroster Low Cab w/ Fixed Lower Front & Side Windows Low cab w/fixed lower front and side opening windows $ Low Cab w/ Lower Front & Side Opening Windows (Includes roof wiring harness for lighting, beacon, precleaner, and heated mirrors) $ Tall Cab w/ Lower Fixed Front & Side Opening Windows $ Grade Pro Low Cab w/lower Front and Side Opening Windows (Requires 1.2 and 2.12) In Configuration Powered Cab Air Precleaner $ Cab w/o Precleaner Standard Fabric Air Suspension Seat w/armrests and Headrest Premium Heated, Leather/Fabric, High-Wide Back, Air Suspension Seat with Armrests. For use with cab codes 2.03, 2.04, 2.05 & This seat does not include a headrest. $ Grade Pro Premium Heated, Leather/Fabric, High-Wide Back Air Suspension Seat (Requires 1.2 and 2.07) In Configuration to-12 Volt Converter (15 amps) to-12 Volt Converter (30 amps) $ Exterior Mounted Rearview Mirrors Heated Exterior Mounted Rearview Mirrors $ Lower Front Intermittent Wiper & Washer $ Less Lower Front window Wiper & Washer AM/FM Radio with CD and Weather Band (WB) $ No Radio Rear Camera (Provides rear view from dash monitor) $ 1, No Rear Camera Front Window Movable Sun Visor $ Rear Retractable Sun Shade $ Decelerator $ lbs. multi purpose (ABC) Dry Chemical Fire Extinguisher $ Secondary Steering $ 1, ENGINE/POWER TRAIN Offer engine and powertrain options. Number starting with 3.1, 3.2, etc Cool-On-Demand Automatic Reversing Hydraulic Fan 3.02 Fluid Sampling Ports (For sampling engine oil, engine coolant, hydraulic oil, axle & transmission fluids) John Deere PowerTech PSX 9.0L meets EPA IT4 / EU Stage IIIB Emissions (195 Net Peak hp) Standard 100 Amp Alternator amp Alternator $ amp Alternator $ Quick Service Bank for Fluid Changes for Transmission, Hydraulic, Engine Oil, and Engine Coolant (Remote service bank is inside engine compartment and includes Industry Standard Quick Disconnect Couplers) $ No Quick Service Group Standard Fuel & Water Filtration Severe Duty Fuel & Water Filtration System $ Fast Fill Fuel System (150 gpm fill rate) $ 1, No Fast Fill Fuel System Hydraulic Pump Disconnect for Cold Weather Starting $ No Hydraulic Pump Disconnect Engine Exhaust with Flat Black Stack for 9.0L (EPA IT4/EU Stage IIIB only) Engine Exhaust with Chrome Stack for 9.0L (EPA IT4/EU Stage IIIB only) $ Autoshift Transmission $ Manual Shift (No Autoshift) Transmission Transmission Solenoid Valve Guard $ No Transmission Solenoid Valve Group Engine Coolant Circulating Heater, 120 Volt, 1500 Watt Included Ether Starting Aid Included Cold Weather Control Valve Covers (Plastic covers that mount below the cab, shielding the control valve from snow and slowing down hydraulic heat loss in winter. Requires 1.2) $ ELECTRICAL/LIGHTS Offer electrical/light options. Number starting with 4.1, 4.2, etc AT Beacon Strobe kit Installed $ Volt to 12 Volt, 15 Amp Converter w/two outlets 4.03 JDLink Ultimate Machine Monitoring System with 3 Year Message Service Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport Lights) (Includes 2 high and 2 low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grill, front and rear LED marker lights, LED brake lights, and LED hazard warning lights) GRADING LIGHTS (10 HALOGEN LIGHTS) Includes code 4.01 Transporting Halogen w/ LED Signal and Marker Lights, plus (6) Work lights: (2) on bottom of cab, (2) on midframe, and (2) reversing lights on rear grill. $ DELUXE GRADING LIGHTS (16 HALOGEN LIGHTS) NOTE: * Includes code 4.05 Grading Lights plus (6) additional work lights: (4) Corner Cab Work Lights and (2) Front Cab Work Lights.* Requires code amp Altenator or amp Altenator (IT4). $ DELUXE GRADING LIGHTS w/ 2 additional RH Cab Roof Lights (18 HALOGEN LIGHTS) NOTE:* Requires alternator code 3.05 or * Includes code 4.06 Deluxe Grading Lights w/ LED Colored Lights and (2) Additional Rightside Work Lights. $ Two Batteries, Group 4D (1000 CCA, 180 reserve minutes each) $ (48) Two Batteries, Group 4D (1400 CCA, 440 Reserve Minutes Each) Level 1 Electronic Corrosion Prevention Package (Requires 3.19) $ Tall Front Snow Plow Light Bar 26" higher than Standard Frame Lights. Not for use with Mid Mount Scarifier $ Flip Down Cab Beacon Bracket (RH) For Single Beacon on Cab. $ Flip Down Cab Beacon Bracket (LH) $ TIRES/RIMS

14 Offer tire/rim options Number starting with 5.1, 5.2, etc Less Tires & Wheels (NOTE: NOT AVAILABLE FOR UNIT 3R & 48) $ (4,387) x24 12PR SGG Firestone (G2) Bias Tires w/1 pc. Rim $ 2, x24 12 PR Titan G2 Bias Tires w/1pc. Rim Included In. 12 PR SGG Firestone G2 Bias Tires w/ 3 pc. Rims $ 3, In. 12 PR Titan G2 Bias Tires w/ 3 pc. Rims $ R 24 Inch G2/L2 Single Star XGLA2 Michelin Radial Tires w/ 1 pc. Rims $ 5, R 24 Inch G2/L2 Single Star VUT Bridgestone Radial Tires w/ 1 pc. Rims $ 4, R 24 Inch G2/L2 Single Star XGLA2 Michelin Radial Tires w/ 3 pc. Rims $ 6, R 24 Inch G2/L2 Single Star VUT Bridgestone Radial Tires w/ 3 pc. Rims $ 5, R 24 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 1 pc. Rims $ 7, In. 12 PR G2/L2 SGG Firestone Bias Tires w/ 1 pc. Rims $ 3, X25 12 ply L2 Goodyear Radial Tires on 1 pc. Rims $ 4, In. 12 PR G2/L2 SGG Firestone Bias Tires w/ 3 pc. Rims $ 4, X25 12 ply L2 Goodyear Tires on 3 pc. Rims $ 6, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 1 pc. Rims $ 6, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 1pc. Rims $ 6, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 1 pc. Rims $ 3, R25 L3 Goodyear Radial Tires on 1 pc. Rims $ 13, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 3 pc. Rims $ 8, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 3pc. Rims $ 7, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 3 pc. Rims $ 5, X25 12 ply L2 Goodyear Tires on 3 pc. Rims $ 14, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 1 pc. Rims $ 8, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 3 pc. Rims $ 9, R 25 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 1 pc. Rims $ 9, R 25 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 1 pc. Rims $ 7, R25 Goodyear Snow Tires on 1 pc. Rims $ 11, Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 1 pc. Rim $ 3, Front Fenders $ No Front Fenders Rear Wheel Fenders in.(476mm) Rear Wheel Fenders Fenders are not for use with 550 tires. Fenders can only be used with chains that are designed for 3" of radial clearance and 1.75" of sidewall clearance. Use of Tire chains permitted in accordance with SAE J683, and requires removal of front mud flap on rear fenders. $ 1, HYDRAULICS Offer hydraulic options. Number starting with 6.1, 6.2, etc. Right Hand - Standard Hydraulic Controls Base Hydraulics - 4 Function Controls Requires code 1.1. Base Functions: Rear Steer, Circle Side shift, Wheel Lean & RH Blade Lift w/ Float Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base functions plus 1 function w/float control - front plumbing and hoses for Scarifier or auxiliary applicaton. For Use with Front Scarifier. $ Mid Mount Scarifier Base Hydraulics w/ 1 Auxiliary Function Control Requires Mid Mount Scarifier code and 1.1. Midmount scarifier base hydraulics with 1 auxilliary function control with float control for mid mount scarifier. For use with mid mount scarifier. $ Base Hydraulics w/2 Auxiliary Function Controls Requires code 1.1. Base functions plus 2 functions w/float control - front plumbing and hoses for Scarifier and/or auxiliary application.for Use with Front Scarifier. $ 1, Base Hydraulics w/ 3 Auxiliary Function Controls Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o float control, front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ 2,131 Right Hand - GRADE PRO CONTROLS Finger-tip armrest mounted controls, consistent with the industry standard pattern. Includes armrest mounted lever steering plus the traditional steering wheel. All Auxiliary codes include front and rear plumbing for each Auxiliary function Grade Pro Controls for Mid Mount Scarifier w/1 Auxiliary Function Control Requires codes 1.2 and Mid Mount Scarifier code $ Grade Pro Controls with Base Functions NOTE: * Requires code 1.2. * Grade Pro Base Hydraulics Functions: Rear Steer, Circle Side shift, Wheel Lean, Right and Left hand Blade Lift w/ Float, Circle Rotate, Blade Side Shift, Blade Tilt, Lever Steering (also includes steering wheel) In Configuration Grade Pro Controls w/1 Rear Auxiliary Function and Left Hand Lever Controller Requires code 1.2. Base functions plus 1 auxiliary function w/float control - Rear plumbing and hoses for Ripper or auxiliary applicaton. For Use with Rear Ripper. $ Grade Pro Controls w/1 Front Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 FRONT auxiliary function w/float control - front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ Grade Pro Controls w/1 Rear Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 REAR auxiliary function w/float control - front plumbing and hoses for auxiliary application. $ Grade Pro Controls w/1 Front Auxiliary Function and 2 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 3 auxiliary functions- 1 front and 2 rear auxiliary functions w/ float control and rear plumbing for Scarifier / Ripper and/or front, mid $ 2, Grade Pro Controls w/1 Front, 1 Rear Auxiliary Function Control with Right and Left hand Controllers Requires code 1.2. Base Functions plus 2 auxiliary functions - 1 front and 1 rear with float control and plumbing Scarifier / Ripper applications. Auxiliary functions have reconfigurable controls. $ 1, Grade Pro Controls w/1 Front Auxiliary Function and 3 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 4 auxiliary functions - 1 front and 3 rear with float control and plumbing for Scarifier/Ripper and/or front, mid and rear auxiliary applications. Auxiliary functions have reconfigurable controls. $ 3, Grade Pro Controls w/3 Front and 3 Rear Auxiliary Function Controls with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 6 auxiliary functions-3 front and 3 rear with float control on 4 functions, and includes front and rear plumbing for 2 Functions each. Auxiliary functions have reconfigurable controls. $ 4,611 Left Hand - Standard hydraulic Controls Base Hydraulics- 4 Function Controls Requires code 1.1. Base Functions: LH Blade Lift w/ Float, Blade Side shift, Circle Rotate, Blade Tilt Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base Functions plus 1 function w/float control and lines for Ripper or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 675

15 Base Hydraulics w/2 Auxiliary Function Control Requires code 1.1. Base functions plus 2 functions w/float control and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 1, Base Hydraulics w/ 3 Auxiliary Function Control Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o Float Control, and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 2, Grade Pro Controls - Left Side NOTE: * Requires code 1.2. * Accompanies GRADE PRO CONTROLS - RIGHT SIDE order code selection. In Configuration Oil, SAE 10W AW46 All Season Hydraulic Oil $ Hydraulic Oil, ISO 46 $ MOLDBOARD/CUTTING EDGE/END BITS/CIRCLE DRIVE Offer these options starting with 7.1, 7.2, 7.3, etc Blade Impact Absorption System Protects Moldboard and draft frame from impacts with Stationary objects $ 1, No Blade Impact Absorption system Ft. x 24 In. x 7/8 In. (3.66 M x 610 mm x 22 mm) with 6 In. x 5/8 In. (152 x 16 mm) Cutting Edge and 5/8 in. (16mm) Hardware Ft. x 24 In. x 7/8 In. (3.66 M x 610 mm x 22 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (3.66 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (3.96 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 24 In. x 7/8 In. (4.27 M x 610 mm x 22 mm) with 6 In. x 5/8 In. (152 x 16 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 24 In. x 7/8 In. (4.27 M x 610 mm x 22 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edgeand 5/8 in. (16mm) Hardware NOTE: Requires engine code $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 3/4 in. (19mm) Hardware Requires engine code $ Extended Life Bronze Wear Inserts NOTE: Recommended for applications in abrasive material. $ Wear Inserts w/o Clutch (Recommended for higher circle torque) Nylon Wear Inserts w/clutch Requires code 7.19 Circle Drive Slip Clutch. Recommended for higher circle torque when used with a slip clutch. $ Reversible Overlay End Bits Not avaible for unit 3R & 48. $ No Reversible Overlay End Bits No Moldboard Extension " 24 in. Left Hand Moldboard Extension Requires Moldboard code 7.08,7.09, or Not available for units 3R & 48. $ 1, " 24 in. Right Hand Moldboard Extension NOTE: * Requires Moldboard code 7.08,7.09, or * Available to all other units with no restrictions. $ 1, Circle Drive with Slip Clutch Protects circle, circle drive gearbox and draft frame from damage when end of moldboard comes in contact with stationary objects. Slip clutch is integral to the circle drive assembly and utilizes a wet clutch system. Can not be used with code 7.04 inserts. $ 1, AT Moldboard Extension, 24 X 24 X 7/8 In. Left Hand 7/8 in. (22mm) thick. Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 24 x 24 x 7/8 In. Right Hand 7/8 in. (22mm) thick. Requires 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 2, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 1, FRONT ATTACHMENTS Offer front attachment options. Starting with 8.1, 8.2, etc. *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & Additional Charges Front Push Block $ 1, Front Scarifier Includes Front Hydraulics, plumbing and hoses Scarifier with 2 pitch positions and 9 shank pockets Five 1 x 3 inch Scarifier Shanks w/teeth If additional shanks are desired order (1) each of T6Y5230 Tooth, T Shank and T Retainer for each set. Can not be used with 6.07 Hydraulics. $ 4, Mid-Mount Scarifier with Integrated Front Push Plate NOTE: * Requires code 6.03 or 6.06 Hydraulics. * Mid-Mount Scarifier with Push Block Can not be used with Front Scarifier. * Not for use with Front Fenders Code * Recommend Rear Counterweight for better machine balance. $ 6, Balderson Style Front Lift Group NOTE: * Requires Hydraulic code 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13, or * (2) AT Mating Hooks from Parts are available to convert old front attachments to the Bladerson-style lift group. $ 3, Less Front Attachment Front-Mounted Dozer Blade, 97 in. x 37.6 in. (2464 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or Requires one of the following 14.0 x 24 tire codes: 5.01, 5.02, 5.03, 5.04, 5.05, 5.06, 5.07, 5.08, 5.09, or $ 4, Front-Mounted Dozer Blade, 105 in. x 37.6 in. (2667 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires one of the following 17.5 x 25 tire codes: 5.01, 5.11, 5.13, 5.15, 5.16, 5.17, 5.19, 5.20, 5.21, 5.23, 5.24, 5.25, 5.26 $ 4,647 FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Front Hitch Systems - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Standard Hitch System (Pin-on style hitch. 3.5 double acting lift cylinder with 2 rod.) $ 2, Falls Modified 29" Husting Hitch System (Drive -in quick coupler with vertical lift. 3.5 double acting lift cylinder with 2 rod.) $ 3, Falls Modified 34" Husting Hitch System $ 4, Para-Lift Model PLS-1 Hitch System (Drive-in parallel lift quick coupler. $ 3,987

16 Front Hitch System Options Hydraulic Locking Pin Assembly for Para-Lift Hitch $ Factory Installation of Hydraulic Locking Pin Assy for Para-Lift Hitch $ One Pair Attachment Hooks, Flat Back for Para-Lift Hitch (*Not installed) $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 One Way Snow-Plows Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge, 9'10" Clearing Width w/ Standard Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 29" Husting Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 34" Husting Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Para-Lift Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Scar-a-Lift or Deere Front Mounted Scarifier Coupler $ 8,110 One Way Snow Plow Options Carbide cutting edge, three (3) pc., 3/4 x 6, per foot $112/ft Rubber belt deflector, 3/8 x 12 $ Heavy duty Spring Trip Tilt Bars, add $ Heavy duty Trip Edge Assembly, add $ 1, Hydraulic Moldboard Tilt, replaces rigid or spring trip bars, add $ Steel caster wheel assemblies, add $ 1, Pneumatic caster wheel assemblies, add $ 1, Left hand discharge, add $ Snow Wheel System, add $ 2,023 V-Type Snow Plows - Select the Hitch Attachment Coupler from the Options Falls V-890, 10 gauge A steel moldboard, 10 8 overall width, 9 8 clearing width, 48 nose height, 72 discharge height, three (3) screw-adjustable skid shoes (no tools required), spring loaded snow deflectors $ 6, Falls V-90, 7 gauge A steel moldboard, 12 0 overall width, 9 8 clearing width, 60 nose height, 84 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 6, Falls V-100, 7 gauge A steel moldboard, 13 3 overall width, 10 4 clearing width, 66 nose height, 92 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 8,342 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System $ 1, Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 2, Plow Unit to fit Falls Para-Lift Hitch System w/oscillating feature $ 1, Plow Unit to fit Falls Para-Lift Hitch System (hooks welded solid) $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,360 V-Type Snow Plow Options Spring Loaded Steel Snow Deflectors (Standard on the Falls V-890) $ Rubber Belt Snow Deflector (3/8" x 12") $ Down Pressure Kit for Standard and Modified Husting Hitch Systems $ Snow-Wheel System (In lieu of standard shoes) $ 4,228 Heavy Duty Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options Falls HDR-11, 11' Cutting Edge, 48" High (*Select Hitch from Options) $ 8, Falls HDR-12, 12' Cutting Edge, 48" High (*Select Hitch from Options) $ 8,958 Hitch Attachment Couplers Plow Unit to fit Falls Para-Lift Hitch System $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2, Optional Oscillation Plate (allows plow to follow road contour) $ 1,545 Heavy Duty Reversible Snow Plow Options Carbide Cutting Edge, Add per foot $112//ft Rubber Belt Snow Deflector (3/8" x 12") $ Moldboard Shoes (*Standard Equipment - Not available w/ trip edge assembly) No Charge Screw Adjustable Mushroom Shoes - Set of Two (Can be used with trip edge assembly) $ Trip Edge Assembly (One-piece construction) $ 1,709 Power Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options PR1143 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 6, PR1243 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 7, PR1155/PR1255 Raise moldboard height on PR1143 or PR1243, add to respective snow plow $ TER-11 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6, TER-12 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6,884 Plow-Hitch System Attachment Provides Full Oscillation Left and Right Plow Unit to fit Falls Standard Hitch System $ Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 1, Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,032 Power Reversible Snow Plow Options Trip Edge Assembly $ 1, Carbide Cutting Edge Per Foot $112/ft Rubber Belt Snow Deflector, 3/8" x 12" $ Steel Caster Wheel Assemblies $ 1, Pneumatic Caster Wheel Assemblies $ 1, Curb Shoe, Cylindrical, Each $ Curb Shoe, Wrap-Around, Each $ Snow-Wheel System (In lieu of standard shoes) $ 2,729 Dozer Blades - Select the Hitch Attachment Coupler from the Options Falls D3696, 8 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36108, 9 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4,415

17 8.090 Falls D36120, 10 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4,620 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System No Charge Plow Unit to fit Falls Modified 29" Husting Hitch System No Charge Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 1,923 Dozer Blade Options Carbide Cutting Edge, Per Foot $112/ft Scar-A-Lift - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Model FMS-1 Front Mounted Scarifier $ 5,199 Scar-A-Lift Options Scarifier, Head Only, 5 Teeth, No Head Plate or Arms $ 2, Scarifier, Head Only, 5 Teeth, Para-Lift Hooks Installed $ 3, Scarifier Shank, End Bit and Retainer (Each) $ Para-Lift Attachment Hooks, Flat Back, Per Pair $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 HENKE SNOW ATTACHMENTS Henke Fixed Position Dozer Blades DB8 8' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB9 9' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB10 10' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5,348 Lift Group (JRB Installation of Lift Group, Including Freight from Leavenworth STB-STD Scarifier Tool Bar - Lift Group (*Requires hoses to the nose of the motor grader) $ 4, PLG-STD Parallel Lift Group (*Requires hoses to the nose of the motor grader) $ 3, AQC Automatic Quick Coupler Lift Group (*Requires hoses to the nose of the motor grader) $ 5, HSH Henke Universal Hitch for Grader $ 2,596 Attachment Adapter PSS Plow Scarifier Sockets - Mounts to Henke or Factory Scarifier (Specify) $ PLH Parallel Lift Hooks - Mounts to Henke or field "Balderson Style" Lift Group $ AQC Female Attaching Adapter $ 1,367 Henke REL - Heavy Duty Reversible Snow Plow REL 10 10' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 12 12' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 14 14' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 12, REL 16 16' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 13,957 Henke SDDB - Severe Duty Dozer Blade SDDB 10 10' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 12 12' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 14 14' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12, SDDB 16 16' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12,356 Henke HH - Henke Helper Utility Blade HH 8 8' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 9 9' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 10 10' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 8,067 Henke FV - Multi-Directional Folding Vee Snowplow (MDFVS) FV 12 12' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 14, FV 14 14' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 15, FV 16 16' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS ) $ 16,622 Henke Tube Table Power Reversible Snow Plows (Include Grader Adaptor) R11TT 50" Tall, Power Reversible Trip Plow w/tube Table Reversing Frame $ 7, R12TT 50" Tall, Power Reversible Trip Plow w/tube Reversing Frame $ 8,095 Henke Plow Options Mushroom Shoes - Pair $ Install Dealer Supplied Coupler $ Parallel Lift Hook Coupler-Supply/Install $ JRB Style Coupler (Verify size and type) $ Hydraulic Hi-Gate for REL (Includes diverter Kit) $ 6, Trip Lockout Option $ ACS Coupler-Supply/Install $ 1,595 Henke V-Plow V-9.5 Vee Plow 9.5 Foot Cutting Swath $ 6, V-10 Vee Plow 10 Foot Cutting Swath $ 7,602

18 9.0 REAR ATTACHMENTS Offer rear attachment options. Starting with 9.1, 9.2, etc No Rear Attachment Rear Mounted Ripper/Scarifier Combination with Rear Hitch and Pin Includes Rear mounted Ripper/Scarifier with rear hitch and pin. NeverGrease Pin Joints. Three 2 x 5 in. Ripper Shanks w/teeth. Can not be used with codes 6.07, 6.09 or $ 8, Rear Counterweight with Rear Hitch and Pin 1600 lbs.(725.7 kg.) Rear Counterweight. Recommend for use with Front / Mid Scarifier. $ 1, Rear Hitch and Pin Not for use with Rear Ripper/Scarifier. $ (9) Extra Scarifier Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ (2) Extra Ripper Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ Slow Moving Vehicle (SMV) Sign Included Handi Hitch *Prices Do Not Include Mounting PP01G Handi Hitch Profile Packer/Roller 90" includes Lift Plate, 24" Packer Offset No Installation Included $ 18, HH01G 870GP Lift Assembly/Offset $ 3, PP04G Profile Accumulator and Hoses $ CR10 Handi Hitch Contour Packer/Roller 75" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR12 Handi Hitch Contour Packer/Roller 90" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR14 Handi Hitch Contour Packer/Roller 105" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 19, CR30 Contour/PP Ripper Shanks $ 1, WR30E Contour Ripper Shank Extender Plates $ CR40 Handi Hitch Contour 24" Packer Offset $ 2, CR50 Handi Hitch Contour Heavy Duty Lift Assembly $ 4, CR55 Handi Hitch Contour Accumulator and Hoses $ CR59 John Deere Link Arms (Lift Assembly) $ SIDE ATTACHMENTS Offer side attachment options. Starting with 10.1, 10.2, etc. FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Wings Falls W12 Wing Only, 12 ft. cutting edge moldboard, 36 height, hydraulic-over-cable controls, rear wing post height is manually adjustable. $ 11, Falls W-14 Wing Only, 14 ft. moldboard cutting edge. $ 12, Falls 2012A Wing Only, 12 ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys, rear wing post height is manually adjustable. $ 12, Falls 2012A Low Post (66" vs 100") $ 12, Falls 2014A Wing Only, 14 ft. moldboard cutting edge. $ 13,090 Invisible Mast Snow Wings (Mast Post Fits Under Cab for Maximum Visibility) IM ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys.invisible Mast post fits under cab allowing maximum visibility. $ 17, IM3014 Same as above w/14' Moldboard $ 17,510 Options for Falls Wings Hydraulic Extendable Buffer Brace $ 2, Hydraulic Elevating Rear Slide $ Trip Edge Assembly for 12 Foot Add $ 1, Trip Edge Assembly for 14 Foot Add $ 1, Left Hand Discharge Add $ Ripper Mount in Lieu of Rear Wing Post and Slide No charge HENKE SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included Price Includes Installation at Factory Wings AHW12FR 12' Grader Wing for Fixed Rear Applications (*Requires 2 valves) $ 11, AHW12MR 12' Grader Wing for Manual Adjusting Rear Applications (*Requires 2 valves) $ 11, AHW12RR 12' Grader Wing for Rear Ripper Applications (*Requires 2 valves) $ 10, AHW12ER 12' Grader Wing for Elevating (Benching) Applications (*Requires 3 valves) $ 12,328 Wing Options ' Grader Moldboard $ Trip Edge Option $ Hi-Gate - Hydraulic End Gate (Includes a diverter kit) $ 4, Factory Installation Wing installation by JRB at the John Deere Factory Included STB-STD Scarifier Tool Bar $ 3, PLG-STD Parallel Lift Group $ 3, AQC Automatic Lift Group $ 4, HSH Henke Standard Hitch (Truck style hitch modified for grader) $ 2, JRB Installation of Lift Group in Davenport Including Freight $ 547 Monroe SNOW ATTACHMENTS (ALL PRICES INCLUDE INSTALLATION AT MONROE) Wings AHW12E-62 for JD "G" Series, 12' All Hydraulic Wing Package w/ 62" Bench Height, 5/8" x 8" Cutting Edge $ 15, AHW12E-38 for JD "G" Series, 12' All Hydraulic Wing Package w/ 38" Bench Height, 5/8" x 8" Cutting Edge $ 15,305 Wing Options Deduct to delete rear post assembly and use ripper-mount bracketry in it's place $ (1,553) Deduct to delete rear post and use 2-position fixed post in it's place $ (1,015) ' Wing Moldboard in Lieu of Standard 12' Model (Requires and/or 10.28) $ Front Lift Group Installed on G-Series Grader $ 5, OTHER ATTACHMENTS Offer other attachment options. Number starting with 11.1, 11.2, etc NS Slopemeter #2 (Installed) $ AT IGC Mast Mounts $ 650 *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & Additional Charges EXTENDED WARRANTY OPTIONS Offer performance/warranty options. Number these starting with 12.1, 12.2, etc. (Specify years, miles or hours extended term covers.) Comprehensive (SEE PRICE MATRIX BELOW)

19 12.02 Power Train and Hydraulics (SEE PRICE MATRIX BELOW) Power Train (SEE PRICE MATRIX BELOW) Engine Only (SEE PRICE MATRIX BELOW) Warranty covers John Deere manufactured components only. Standard Manufacturers Warranty applies to all components that are not manufactured by John Deere Extended Powertrain and Hydraulic Warranty has no Deductible per Occurrence after Initial Warranty - See Attached Extended Warranty Sheet Preventative Maintenance Contract (3 Year/2000 Hour) Cost per Hour $ NEW EQUIPMENT RENTAL PROGRAM If rental programs are available on the new equipment offered, with the option to purchase, list the hourly/weekly/monthly rental rate. Indicate the percent of rental fee paid by the purchaser that will be applied to the purchase price. See Solicitation Special Terms & Conditions. Hourly Rental Rate: NA Weekly Rental Rate: $ 2,570 Monthly Rental Rate: $ 7,700 Percent (%) of Rental Fee applied to purchase price: 100%

20 If the new rental equipment is purchased and finance charges are applicable for the actual rental term only, state the actual interest rate here: NA 14 VENDOR OWNED RENTAL RETURN OR DEMO EQUIPMENT PROGRAM See Solicitation Special Terms and Conditions. DEDUCT cost per Used Hour from the original Contract Price $ DISCOUNT OFF LIST PRICE FOR RELATED PARTS & ACCESSORIES 0% (See Special Terms and Conditions) 16 DELIVERY STARTING POINT City, State, Zip Nearest RDO Equipment or Nortrax Facility RDO Equipment Burnsville, MN Grand Forks, ND Moorehead, MN Rochester, MN Marshal, MN N. Mankato, MN Sauk Rapids, MN Sioux Falls, SD NORTRAX Bemidji, MN Duluth, MN Grand Rapids, MN DELIVERY PRICE PER LOADED MILE No Flat Rate Allowed- See Special Terms and Conditions $6.00 w/$300 Minimum

21 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 1 of 2 Vendor Name: RDO Equipment Company Contact Person: Mike Kluck & Jesse Miller Street Address: DuPont Avenue South P.O. Box: City, State, Zip Burnsville, Minnesota Phone #: Mike: (952) or Jesse: (612) Toll Free #: (800) Fax #: (952) Address: mkluck@rdoequipment.com or jmiller@rdoequipment.com Website: Version of Excel used: Furnish separate price quote for each MOTOR GRADER being offered MOTOR GRADER Make & Model Normal/Variable HP Operating Weight Work lights John Deere 770G Gear 1 (170 hp) Gear 2 (173 hp) Gear 3 (189 hp) Gear 4 (204 hp) Gear 5 (219 hp) Gear 6 (235 hp) Gear 7 (241 hp) Gear 8 (245 hp) 36,130 lb. Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport lights) Includes 2-high and 2-low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grille, front and rear LED marker lights, LED brake lights AND LED hazard warning lights Blade Width 12 Ft Base Width (8 options available) Blade Height 24" Base Height, up to 27 " w/alternative options Blade Thickness 7/8" Base Thickness, and up to 1" w/alternative options Cutting Edge Size 6" x 5/8" Base, and up to 8" x 3/4" w/alternative options Circle drive slip clutch Optional Numbers of Drive Tires 4 Alternator Size 100 Amp Battery CCA (2) Group 4D Batteries 1400 CCA, 440 reserve minutes each. Seat type Fabric Air Suspension Seat with Armrests and Headrest 3 In., (76 mm) Seat Belt w/retractors (Conforms to SAE J386) Differential type Fuel Tank Size Rims, Size in Inches/Type Tires Block Heater, Watts Starting Aid Transmission, Speeds Spiral bevel; hydraulically actuated, clutch type can be applied on-the-go; selectable manual or automatic differential lock 110 Gallon In. 12 PR Titan G2 Bias Tires w/ 3 pc. Rims In. 12 PR Titan G2 Bias Tires 120 Volt, 1500 Watts Ether Starting Aid Direct-drive John Deere PowerShift Plus, modulated shift-on-the-go, Event-Based Shifting (EBS), inching pedal; independent transmission reservoir with separate filtration and cooling system with 125- L/min. (33 gpm) gear pump Shift Lever Position km/h (2.5 mph)

22 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 2 of 2 Shift Lever Position km/h (3.5 mph) Shift Lever Position km/h (4.8 mph) Shift Lever Position km/h (6.8 mph) Shift Lever Position km/h (10.2 mph) Shift Lever Position km/h (14.4 mph) Shift Lever Position km/h (20.1 mph) Shift Lever Position km/h (28.3 mph) Forward/Reverse 8 Forward / 8 Reverse (2.5 mph to 28.3 mph) Auto Shift/Manual/Power shift Optional Auto Shift/Manual N/A/Power Shift Standard Heater BTU 31,500 BTU (A/C Standard) Window openings (2) Doors and (2) Left and (2) Right. Front lower and rear sides. Hydraulics Closed-center, pressurecompensated load-sensing (PCLS), variable-displacement piston pump, O-ring face-seal fi ttings Maximum Pump Flow 212 L/min. (56 gpm) Maximum System Pressure kpa (2,750 psi) Pump Displacement 90 cm3 (5.5 cu. in.) Cab Profile/Height Warranty Low Profile ROPS Cab, 10' 5" to top of cab 1 Year Full Machine Warranty BASE PRICE $ 178, John Deere 770G Motor Grader 1.1 BASE MACHINE as stated above. "Included" denotes included in $ 178, BASE PRICE G Grader w/standard Hydraulic Controls GP Grader w/grade Pro EH Controls (Includes finger tip $ 18, controls w/industry standard control pattern, cross slope, Topcon and Trimble ready, return to straight, lever steering and conventional steering wheel) 1.3 Transportation to Monroe Snow & Ice Equipment for Attachment $ 1, Installation 1.4 Transportation to Little Falls Machine, Inc. for Attachment Installation $

23 Qty Price 2.0 OPERATOR STATION Offer operator station options. Number the items starting with 2.1, 2.2, etc., 2.01 Air Conditioning 2.02 Cab Rear Window Electric Defroster Low Cab w/ Fixed Lower Front & Side Windows Low cab w/fixed lower front and side opening windows $ Low Cab w/ Lower Front & Side Opening Windows (Includes roof wiring harness for lighting, beacon, precleaner, and heated mirrors) $ Tall Cab w/ Lower Fixed Front & Side Opening Windows $ Grade Pro Low Cab w/lower Front and Side Opening Windows (Requires 1.2 and 2.12) In Configuration Powered Cab Air Precleaner $ Cab w/o Precleaner Standard Fabric Air Suspension Seat w/armrests and Headrest Premium Heated, Leather/Fabric, High-Wide Back, Air Suspension Seat with Armrests. For use with cab codes 2.03, 2.04, 2.05 & This seat does not include a headrest. $ Grade Pro Premium Heated, Leather/Fabric, High-Wide Back Air Suspension Seat (Requires 1.2 and 2.07) In Configuration to-12 Volt Converter (15 amps) to-12 Volt Converter (30 amps) $ Exterior Mounted Rearview Mirrors Heated Exterior Mounted Rearview Mirrors $ Lower Front Intermittent Wiper & Washer $ Less Lower Front window Wiper & Washer AM/FM Radio with CD and Weather Band (WB) $ No Radio Rear Camera (Provides rear view from dash monitor) $ 1, No Rear Camera Front Window Movable Sun Visor $ Rear Retractable Sun Shade $ Decelerator $ lbs. multi purpose (ABC) Dry Chemical Fire Extinguisher $ Secondary Steering $ 1, ENGINE/POWER TRAIN Offer engine and powertrain options. Number starting with 3.1, 3.2, etc Cool-On-Demand Automatic Reversing Hydraulic Fan 3.02 Fluid Sampling Ports (For sampling engine oil, engine coolant, hydraulic oil, axle & transmission fluids) John Deere PowerTech PSX 9.0L meets EPA IT4 / EU Stage IIIB Emissions (195 Net Peak hp) Standard 100 Amp Alternator amp Alternator $ amp Alternator $ Quick Service Bank for Fluid Changes for Transmission, Hydraulic, Engine Oil, and Engine Coolant (Remote service bank is inside engine compartment and includes Industry Standard Quick Disconnect Couplers) $ No Quick Service Group Standard Fuel & Water Filtration Severe Duty Fuel & Water Filtration System $ Fast Fill Fuel System (150 gpm fill rate) $ 1, No Fast Fill Fuel System Hydraulic Pump Disconnect for Cold Weather Starting $ No Hydraulic Pump Disconnect Engine Exhaust with Flat Black Stack for 9.0L (EPA IT4/EU Stage IIIB only) Engine Exhaust with Chrome Stack for 9.0L (EPA IT4/EU Stage IIIB only) $ Autoshift Transmission $ Manual Shift (No Autoshift) Transmission Transmission Solenoid Valve Guard $ No Transmission Solenoid Valve Group Engine Coolant Circulating Heater, 120 Volt, 1500 Watt Included Ether Starting Aid Included Cold Weather Control Valve Covers (Plastic covers that mount below the cab, shielding the control valve from snow and slowing down hydraulic heat loss in winter. Requires 1.2) $ ELECTRICAL/LIGHTS Offer electrical/light options. Number starting with 4.1, 4.2, etc AT Beacon Strobe kit Installed $ Volt to 12 Volt, 15 Amp Converter w/two outlets 4.03 JDLink Ultimate Machine Monitoring System with 3 Year Message Service Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport Lights) (Includes 2 high and 2 low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grill, front and rear LED marker lights, LED brake lights, and LED hazard warning lights) GRADING LIGHTS (10 HALOGEN LIGHTS) Includes code 4.01 Transporting Halogen w/ LED Signal and Marker Lights, plus (6) Work lights: (2) on bottom of cab, (2) on midframe, and (2) reversing lights on rear grill. $ DELUXE GRADING LIGHTS (16 HALOGEN LIGHTS) NOTE: * Includes code 4.05 Grading Lights plus (6) additional work lights: (4) Corner Cab Work Lights and (2) Front Cab Work Lights.* Requires code amp Altenator or amp Altenator (IT4). $ DELUXE GRADING LIGHTS w/ 2 additional RH Cab Roof Lights (18 HALOGEN LIGHTS) NOTE:* Requires alternator code 3.05 or * Includes code 4.06 Deluxe Grading Lights w/ LED Colored Lights and (2) Additional Rightside Work Lights. $ Two Batteries, Group 4D (1000 CCA, 180 reserve minutes each) $ (47) Two Batteries, Group 4D (1400 CCA, 440 Reserve Minutes Each) Level 1 Electronic Corrosion Prevention Package (Requires 3.19) $ Tall Front Snow Plow Light Bar 26" higher than Standard Frame Lights. Not for use with Mid Mount Scarifier $ Flip Down Cab Beacon Bracket (RH) For Single Beacon on Cab. $ Flip Down Cab Beacon Bracket (LH) $ 56

24 5.0 TIRES/RIMS Offer tire/rim options Number starting with 5.1, 5.2, etc Less Tires & Wheels (NOTE: NOT AVAILABLE FOR UNIT 3R & 48) $ (5,182) In. 12 PR SGG Firestone G2 Bias Tires w/ 3 pc. Rims $ 2, In. 12 PR Titan G2 Bias Tires w/ 3 pc. Rims Included R 24 Inch G2/L2 Single Star XGLA2 Michelin Radial Tires w/ 1 pc. Rims $ 4, R 24 Inch G2/L2 Single Star VUT Bridgestone Radial Tires w/ 1 pc. Rims $ 3, R 24 Inch G2/L2 Single Star XGLA2 Michelin Radial Tires w/ 3 pc. Rims $ 5, R 24 Inch G2/L2 Single Star VUT Bridgestone Radial Tires w/ 3 pc. Rims $ 4, R 24 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 1 pc. Rims $ 6, In. 12 PR G2/L2 SGG Firestone Bias Tires w/ 3 pc. Rims $ 3, X25 12 ply L2 Goodyear Tires on 3 pc. Rims $ 5, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 1 pc. Rims $ 5, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 1pc. Rims $ 5, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 1 pc. Rims $ 2, R25 L3 Goodyear Radial Tires on 1 pc. Rims $ 12, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 3 pc. Rims $ 7, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 3pc. Rims $ 6, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 3 pc. Rims $ 4, X25 12 ply L2 Goodyear Tires on 3 pc. Rims $ 13, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 1 pc. Rims $ 7, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 3 pc. Rims $ 8, R 25 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 1 pc. Rims $ 8, R 25 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 1 pc. Rims $ 6, R25 Goodyear Snow Tires on 1 pc. Rims $ 10, R25 Goodyear Snow Tires on 3 pc. Rims $ 11, /65R25 XLD70 G3/L3 Single Star Michelin Low Profile Radial Tires w/3 pc Rims (Requires code 5.30 No Front Fenders. Can not be used with code 5.31 Rear Fenders.) $ 14, Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 1 pc. Rim $ 3, Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 3 pc. Rim $ 4, Front Fenders $ No Front Fenders Rear Wheel Fenders in.(476mm) Rear Wheel Fenders Fenders are not for use with 550 tires. Fenders can only be used with chains that are designed for 3" of radial clearance and 1.75" of sidewall clearance. Use of Tire chains permitted in accordance with SAE J683, and requires removal of front mud flap on rear fenders. $ 1, HYDRAULICS Offer hydraulic options. Number starting with 6.1, 6.2, etc. Right Hand - Standard Hydraulic Controls Base Hydraulics - 4 Function Controls Requires code 1.1. Base Functions: Rear Steer, Circle Side shift, Wheel Lean & RH Blade Lift w/ Float Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base functions plus 1 function w/float control - front plumbing and hoses for Scarifier or auxiliary applicaton. For Use with Front Scarifier. $ Mid Mount Scarifier Base Hydraulics w/ 1 Auxiliary Function Control Requires Mid Mount Scarifier code and 1.1. Midmount scarifier base hydraulics with 1 auxilliary function control with float control for mid mount scarifier. For use with mid mount scarifier. $ Base Hydraulics w/2 Auxiliary Function Controls Requires code 1.1. Base functions plus 2 functions w/float control - front plumbing and hoses for Scarifier and/or auxiliary application.for Use with Front Scarifier. $ 1, Base Hydraulics w/ 3 Auxiliary Function Controls Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o float control, front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ 2,098 Right Hand - GRADE PRO CONTROLS Finger-tip armrest mounted controls, consistent with the industry standard pattern. Includes armrest Grade Pro Controls for Mid Mount Scarifier w/1 Auxiliary Function Control Requires codes 1.2 and Mid Mount Scarifier code $ Grade Pro Controls with Base Functions NOTE: * Requires code 1.2. * Grade Pro Base Hydraulics Functions: Rear Steer, Circle Side shift, Wheel Lean, Right and Left hand Blade Lift w/ Float, Circle Rotate, Blade Side Shift, Blade Tilt, Lever Steering (also includes steering wheel) In Configuration Grade Pro Controls w/1 Rear Auxiliary Function and Left Hand Lever Controller Requires code 1.2. Base functions plus 1 auxiliary function w/float control - Rear plumbing and hoses for Ripper or auxiliary applicaton. For Use with Rear Ripper. $ Grade Pro Controls w/1 Front Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 FRONT auxiliary function w/float control - front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ Grade Pro Controls w/1 Rear Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 REAR auxiliary function w/float control - front plumbing and hoses for auxiliary application. $ Grade Pro Controls w/1 Front Auxiliary Function and 2 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 3 auxiliary functions- 1 front and 2 rear auxiliary functions w/ float control and rear plumbing for Scarifier / Ripper and/or front, mid $ 2, Grade Pro Controls w/1 Front, 1 Rear Auxiliary Function Control with Right and Left hand Controllers Requires code 1.2. Base Functions plus 2 auxiliary functions - 1 front and 1 rear with float control and plumbing Scarifier / Ripper applications. Auxiliary functions have reconfigurable controls. $ 1, Grade Pro Controls w/1 Front Auxiliary Function and 3 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 4 auxiliary functions - 1 front and 3 rear with float control and plumbing for Scarifier/Ripper and/or front, mid and rear auxiliary applications. Auxiliary functions have reconfigurable controls. $ 3, Grade Pro Controls w/3 Front and 3 Rear Auxiliary Function Controls with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 6 auxiliary functions-3 front and 3 rear with float control on 4 functions, and includes front and rear plumbing for 2 Functions each. Auxiliary functions have reconfigurable controls. $ 4,540 Left Hand - Standard hydraulic Controls Base Hydraulics- 4 Function Controls Requires code 1.1. Base Functions: LH Blade Lift w/ Float, Blade Side shift, Circle Rotate, Blade Tilt Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base Functions plus 1 function w/float control and lines for Ripper or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 665

25 Base Hydraulics w/2 Auxiliary Function Control Requires code 1.1. Base functions plus 2 functions w/float control and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 1, Base Hydraulics w/ 3 Auxiliary Function Control Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o Float Control, and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 2, Grade Pro Controls - Left Side NOTE: * Requires code 1.2. * Accompanies GRADE PRO CONTROLS - RIGHT SIDE order code selection Oil, SAE 10W AW46 All Season Hydraulic Oil $ Hydraulic Oil, ISO 46 $ MOLDBOARD/CUTTING EDGE/END BITS/CIRCLE DRIVE Offer these options starting with 7.1, 7.2, 7.3, etc Blade Impact Absorption System Protects Moldboard and draft frame from impacts with Stationary objects $ 1, No Blade Impact Absorption system Ft. x 24 In. x 7/8 In. (3.66 M x 610 mm x 22 mm) with 6 In. x 5/8 In. (152 x 16 mm) Cutting Edge and 5/8 in. (16mm) Hardware Ft. x 24 In. x 7/8 In. (3.66 M x 610 mm x 22 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (3.66 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (3.96 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 24 In. x 7/8 In. (4.27 M x 610 mm x 22 mm) with 6 In. x 5/8 In. (152 x 16 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 24 In. x 7/8 In. (4.27 M x 610 mm x 22 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edgeand 5/8 in. (16mm) Hardware NOTE: Requires engine code $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 3/4 in. (19mm) Hardware Requires engine code $ Extended Life Bronze Wear Inserts NOTE: Recommended for applications in abrasive material. $ Wear Inserts w/o Clutch (Recommended for higher circle torque) Nylon Wear Inserts w/clutch Requires code 7.19 Circle Drive Slip Clutch. Recommended for higher circle torque when used with a slip clutch. $ Reversible Overlay End Bits Not avaible for unit 3R & 48. $ No Reversible Overlay End Bits No Moldboard Extension " 24 in. Left Hand Moldboard Extension Requires Moldboard code 7.08,7.09, or Not available for units 3R & 48. $ 1, " 24 in. Right Hand Moldboard Extension NOTE: * Requires Moldboard code 7.08,7.09, or * Available to all other units with no restrictions. $ 1, Circle Drive with Slip Clutch Protects circle, circle drive gearbox and draft frame from damage when end of moldboard comes in contact with stationary objects. Slip clutch is integral to the circle drive assembly and utilizes a wet clutch system. Can not be used with code 7.04 inserts. $ 1, AT Moldboard Extension, 24 X 24 X 7/8 In. Left Hand 7/8 in. (22mm) thick. Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 24 x 24 x 7/8 In. Right Hand 7/8 in. (22mm) thick. Requires 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 2, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 1, FRONT ATTACHMENTS Offer front attachment options. Starting with 8.1, 8.2, etc. *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & Additional Charges Front Push Block $ 1, Front Scarifier Includes Front Hydraulics, plumbing and hoses Scarifier with 2 pitch positions and 9 shank pockets Five 1 x 3 inch Scarifier Shanks w/teeth If additional shanks are desired order (1) each of T6Y5230 Tooth, T Shank and T Retainer for each set. Can not be used with 6.07 Hydraulics. $ 4, Mid-Mount Scarifier with Integrated Front Push Plate NOTE: * Requires code 6.03 or 6.06 Hydraulics. * Mid-Mount Scarifier with Push Block Can not be used with Front Scarifier. * Not for use with Front Fenders Code * Recommend Rear Counterweight for better machine balance. $ 6, Balderson Style Front Lift Group NOTE: * Requires Hydraulic code 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13, or * (2) AT Mating Hooks from Parts are available to convert old front attachments to the Bladerson-style lift group. $ 3, Less Front Attachment Front-Mounted Dozer Blade, 105 in. x 37.6 in. (2667 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires one of the following 17.5 x 25 tire codes: 5.01, 5.09, 5.11, 5.12, 5.13, 5.15, 5.16, 5.17, 5.19, 5.20, 5.21, 5.22 $ 4, Front-Mounted Dozer Blade, 115 in. x 37.6 in. (2921 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires 550/65R25 tire code: $ 4,704 FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Front Hitch Systems - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Standard Hitch System (Pin-on style hitch. 3.5 double acting lift cylinder with 2 rod.) $ 2, Falls Modified 29" Husting Hitch System (Drive -in quick coupler with vertical lift. 3.5 double acting lift cylinder with 2 rod.) $ 3, Falls Modified 34" Husting Hitch System $ 4, Para-Lift Model PLS-1 Hitch System (Drive-in parallel lift quick coupler. $ 3,987 Front Hitch System Options

26 8.016 Hydraulic Locking Pin Assembly for Para-Lift Hitch $ Factory Installation of Hydraulic Locking Pin Assy for Para-Lift Hitch $ One Pair Attachment Hooks, Flat Back for Para-Lift Hitch (*Not installed) $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 One Way Snow-Plows Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge, 9'10" Clearing Width w/ Standard Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 29" Husting Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 34" Husting Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Para-Lift Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Scar-a-Lift or Deere Front Mounted Scarifier Coupler $ 8,110 One Way Snow Plow Options Carbide cutting edge, three (3) pc., 3/4 x 6, per foot $112/ft Rubber belt deflector, 3/8 x 12 $ Heavy duty Spring Trip Tilt Bars, add $ Heavy duty Trip Edge Assembly, add $ 1, Hydraulic Moldboard Tilt, replaces rigid or spring trip bars, add $ Steel caster wheel assemblies, add $ 1, Pneumatic caster wheel assemblies, add $ 1, Left hand discharge, add $ Snow Wheel System, add $ 2,023 V-Type Snow Plows - Select the Hitch Attachment Coupler from the Options Falls V-890, 10 gauge A steel moldboard, 10 8 overall width, 9 8 clearing width, 48 nose height, 72 discharge height, three (3) screw-adjustable skid shoes (no tools required), spring loaded snow deflectors $ 6, Falls V-90, 7 gauge A steel moldboard, 12 0 overall width, 9 8 clearing width, 60 nose height, 84 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 6, Falls V-100, 7 gauge A steel moldboard, 13 3 overall width, 10 4 clearing width, 66 nose height, 92 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 8,342 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System $ 1, Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 2, Plow Unit to fit Falls Para-Lift Hitch System w/oscillating feature $ 1, Plow Unit to fit Falls Para-Lift Hitch System (hooks welded solid) $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,360 V-Type Snow Plow Options Spring Loaded Steel Snow Deflectors (Standard on the Falls V-890) $ Rubber Belt Snow Deflector (3/8" x 12") $ Down Pressure Kit for Standard and Modified Husting Hitch Systems $ Snow-Wheel System (In lieu of standard shoes) $ 4,228 Heavy Duty Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options Falls HDR-11, 11' Cutting Edge, 48" High (*Select Hitch from Options) $ 8, Falls HDR-12, 12' Cutting Edge, 48" High (*Select Hitch from Options) $ 8,958 Hitch Attachment Couplers Plow Unit to fit Falls Para-Lift Hitch System $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2, Optional Oscillation Plate (allows plow to follow road contour) $ 1,545 Heavy Duty Reversible Snow Plow Options Carbide Cutting Edge, Add per foot $112//ft Rubber Belt Snow Deflector (3/8" x 12") $ Moldboard Shoes (*Standard Equipment - Not available w/ trip edge assembly) No Charge Screw Adjustable Mushroom Shoes - Set of Two (Can be used with trip edge assembly) $ Trip Edge Assembly (One-piece construction) $ 1,709 Power Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options PR1143 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 6, PR1243 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 7, PR1155/PR1255 Raise moldboard height on PR1143 or PR1243, add to respective snow plow $ TER-11 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6, TER-12 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6,884 Plow-Hitch System Attachment Provides Full Oscillation Left and Right Plow Unit to fit Falls Standard Hitch System $ Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 1, Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,032 Power Reversible Snow Plow Options Trip Edge Assembly $ 1, Carbide Cutting Edge Per Foot $112/ft Rubber Belt Snow Deflector, 3/8" x 12" $ Steel Caster Wheel Assemblies $ 1, Pneumatic Caster Wheel Assemblies $ 1, Curb Shoe, Cylindrical, Each $ Curb Shoe, Wrap-Around, Each $ Snow-Wheel System (In lieu of standard shoes) $ 2,729 Dozer Blades - Select the Hitch Attachment Coupler from the Options Falls D3696, 8 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36108, 9 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36120, 10 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4,620

27 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System No Charge Plow Unit to fit Falls Modified 29" Husting Hitch System No Charge Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 1,923 Dozer Blade Options Carbide Cutting Edge, Per Foot $112/ft Scar-A-Lift - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Model FMS-1 Front Mounted Scarifier $ 5,199 Scar-A-Lift Options Scarifier, Head Only, 5 Teeth, No Head Plate or Arms $ 2, Scarifier, Head Only, 5 Teeth, Para-Lift Hooks Installed $ 3, Scarifier Shank, End Bit and Retainer (Each) $ Para-Lift Attachment Hooks, Flat Back, Per Pair $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 HENKE SNOW ATTACHMENTS Henke Fixed Position Dozer Blades DB8 8' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB9 9' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB10 10' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5,348 Lift Group (JRB Installation of Lift Group, Including Freight from Leavenworth STB-STD Scarifier Tool Bar - Lift Group (*Requires hoses to the nose of the motor grader) $ 4, PLG-STD Parallel Lift Group (*Requires hoses to the nose of the motor grader) $ 3, AQC Automatic Quick Coupler Lift Group (*Requires hoses to the nose of the motor grader) $ 5, HSH Henke Universal Hitch for Grader $ 2,596 Attachment Adapter PSS Plow Scarifier Sockets - Mounts to Henke or Factory Scarifier (Specify) $ PLH Parallel Lift Hooks - Mounts to Henke or field "Balderson Style" Lift Group $ AQC Female Attaching Adapter $ 1,367 Henke REL - Heavy Duty Reversible Snow Plow REL 10 10' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 12 12' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 14 14' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 12, REL 16 16' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 13,957 Henke SDDB - Severe Duty Dozer Blade SDDB 10 10' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 12 12' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 14 14' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12, SDDB 16 16' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12,356 Henke HH - Henke Helper Utility Blade HH 8 8' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 9 9' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 10 10' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 8,067 Henke FV - Multi-Directional Folding Vee Snowplow (MDFVS) FV 12 12' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 14, FV 14 14' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 15, FV 16 16' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS ) $ 16,622 Henke Tube Table Power Reversible Snow Plows (Include Grader Adaptor) R11TT 50" Tall, Power Reversible Trip Plow w/tube Table Reversing Frame $ 7, R12TT 50" Tall, Power Reversible Trip Plow w/tube Reversing Frame $ 8,095 Henke Plow Options Mushroom Shoes - Pair $ Install Dealer Supplied Coupler $ Parallel Lift Hook Coupler-Supply/Install $ JRB Style Coupler (Verify size and type) $ Hydraulic Hi-Gate for REL (Includes diverter Kit) $ 6, Trip Lockout Option $ ACS Coupler-Supply/Install $ 1,595 Henke V-Plow V-9.5 Vee Plow 9.5 Foot Cutting Swath $ 6, V-10 Vee Plow 10 Foot Cutting Swath $ 7, REAR ATTACHMENTS Offer rear attachment options. Starting with 9.1, 9.2, etc.

28 No Rear Attachment Rear Mounted Ripper/Scarifier Combination with Rear Hitch and Pin Includes Rear mounted Ripper/Scarifier with rear hitch and pin. NeverGrease Pin Joints. Three 2 x 5 in. Ripper Shanks w/teeth. Can not be used with codes 6.07, 6.09 or $ 8, Rear Counterweight with Rear Hitch and Pin 1600 lbs.(725.7 kg.) Rear Counterweight. Recommend for use with Front / Mid Scarifier. $ 1, Rear Hitch and Pin Not for use with Rear Ripper/Scarifier. $ (9) Extra Scarifier Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ (2) Extra Ripper Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ Slow Moving Vehicle (SMV) Sign Included Handi Hitch *Prices Do Not Include Mounting PP01G Handi Hitch Profile Packer/Roller 90" includes Lift Plate, 24" Packer Offset No Installation Included $ 18, HH01G 870GP Lift Assembly/Offset $ 3, PP04G Profile Accumulator and Hoses $ CR10 Handi Hitch Contour Packer/Roller 75" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR12 Handi Hitch Contour Packer/Roller 90" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR14 Handi Hitch Contour Packer/Roller 105" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 19, CR30 Contour/PP Ripper Shanks $ 1, WR30E Contour Ripper Shank Extender Plates $ CR40 Handi Hitch Contour 24" Packer Offset $ 2, CR50 Handi Hitch Contour Heavy Duty Lift Assembly $ 4, CR55 Handi Hitch Contour Accumulator and Hoses $ CR59 John Deere Link Arms (Lift Assembly) $ SIDE ATTACHMENTS Offer side attachment options. Starting with 10.1, 10.2, etc. FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Wings Falls W12 Wing Only, 12 ft. cutting edge moldboard, 36 height, hydraulic-over-cable controls, rear wing post height is manually adjustable. $ 11, Falls W-14 Wing Only, 14 ft. moldboard cutting edge. $ 12, Falls 2012A Wing Only, 12 ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys, rear wing post height is manually adjustable. $ 12, Falls 2012A Low Post (66" vs 100") $ 12, Falls 2014A Wing Only, 14 ft. moldboard cutting edge. $ 13,090 Invisible Mast Snow Wings (Mast Post Fits Under Cab for Maximum Visibility) IM ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys.invisible Mast post fits under cab allowing maximum visibility. $ 17, IM3014 Same as above w/14' Moldboard $ 17,510 Options for Falls Wings Hydraulic Extendable Buffer Brace $ 2, Hydraulic Elevating Rear Slide $ Trip Edge Assembly for 12 Foot Add $ 1, Trip Edge Assembly for 14 Foot Add $ 1, Left Hand Discharge Add $ Ripper Mount in Lieu of Rear Wing Post and Slide No charge HENKE SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included Price Includes Installation at Factory Wings AHW12FR 12' Grader Wing for Fixed Rear Applications (*Requires 2 valves) $ 11, AHW12MR 12' Grader Wing for Manual Adjusting Rear Applications (*Requires 2 valves) $ 11, AHW12RR 12' Grader Wing for Rear Ripper Applications (*Requires 2 valves) $ 10, AHW12ER 12' Grader Wing for Elevating (Benching) Applications (*Requires 3 valves) $ 12,328 Wing Options ' Grader Moldboard $ Trip Edge Option $ Hi-Gate - Hydraulic End Gate (Includes a diverter kit) $ 4, Factory Installation Wing installation by JRB at the John Deere Factory Included STB-STD Scarifier Tool Bar $ 3, PLG-STD Parallel Lift Group $ 3, AQC Automatic Lift Group $ 4, HSH Henke Standard Hitch (Truck style hitch modified for grader) $ 2, JRB Installation of Lift Group in Davenport Including Freight $ 547 Monroe SNOW ATTACHMENTS (ALL PRICES INCLUDE INSTALLATION AT MONROE) Wings AHW12E-62 for JD "G" Series, 12' All Hydraulic Wing Package w/ 62" Bench Height, 5/8" x 8" Cutting Edge $ 15, AHW12E-38 for JD "G" Series, 12' All Hydraulic Wing Package w/ 38" Bench Height, 5/8" x 8" Cutting Edge $ 15,305 Wing Options Deduct to delete rear post assembly and use ripper-mount bracketry in it's place $ (1,553) Deduct to delete rear post and use 2-position fixed post in it's place $ (1,015) ' Wing Moldboard in Lieu of Standard 12' Model (Requires and/or 10.28) $ Front Lift Group Installed on G-Series Grader $ 5, OTHER ATTACHMENTS Offer other attachment options. Number starting with 11.1, 11.2, etc NS Slopemeter #2 (Installed) $ AT IGC Mast Mounts $ 650 *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & 12.0 EXTENDED WARRANTY OPTIONS Offer performance/warranty options. Number these starting with 12.1, 12.2, etc. (Specify years, miles or hours extended term covers.) Comprehensive (SEE PRICE MATRIX BELOW)

29 12.02 Power Train and Hydraulics (SEE PRICE MATRIX BELOW) Power Train (SEE PRICE MATRIX BELOW) Engine Only (SEE PRICE MATRIX BELOW) Warranty covers John Deere manufactured components only. Standard Manufacturers Warranty applies to all components that are not manufactured by John Deere Extended Powertrain and Hydraulic Warranty has no Deductible per Occurrence after Initial Warranty - See Attached Extended Warranty Sheet Preventative Maintenance Contract (3 Year/2000 Hour) Cost per Hour $ NEW EQUIPMENT RENTAL PROGRAM If rental programs are available on the new equipment offered, with the option to purchase, list the hourly/weekly/monthly rental rate. Indicate the percent of rental fee paid by the purchaser that will be applied to the purchase price. See Solicitation Special Terms & Conditions. Hourly Rental Rate: NA Weekly Rental Rate: $ 2,570 Monthly Rental Rate: $ 7,700 Percent (%) of Rental Fee applied to purchase price: 100%

30 If the new rental equipment is purchased and finance charges are applicable for the actual rental term only, state the actual interest rate here: NA 14 VENDOR OWNED RENTAL RETURN OR DEMO EQUIPMENT PROGRAM See Solicitation Special Terms and Conditions. DEDUCT cost per Used Hour from the original Contract Price $ DISCOUNT OFF LIST PRICE FOR RELATED PARTS & ACCESSORIES 0% (See Special Terms and Conditions) 16 DELIVERY STARTING POINT City, State, Zip Nearest RDO Equipment RDO Equipment Burnsville, MN Grand Forks, ND Moorehead, MN Rochester, MN Marshal, MN N. Mankato, MN Sauk Rapids, MN Sioux Falls, SD NORTRAX Bemidji, MN Duluth, MN Grand Rapids, MN DELIVERY PRICE PER LOADED MILE No Flat Rate Allowed- See Special Terms and Conditions $6.00 w/$300 Minimum

31 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 1 of 2 Vendor Name: RDO Equipment Company Contact Person: Mike Kluck & Jesse Miller Street Address: DuPont Avenue South P.O. Box: City, State, Zip Burnsville, Minnesota Phone #: Mike: (952) or Jesse: (612) Toll Free #: (800) Fax #: (952) Address: mkluck@rdoequipment.com or jmiller@rdoequipment.com Website: Version of Excel used: Furnish separate price quote for each MOTOR GRADER being offered. 1.1 MOTOR GRADER Make & Model John Deere 772G Normal/Variable HP Gear 1 (6WD on) (202 hp) Gear 2 (6WD on) (205 hp) Gear 3 (6WD on) (220 hp) Gear 4 (6WD on) (226 hp) Gear 5 (6WD on) (244 hp) Gear 6 (6WD on) (255 hp) Gear 7 (6WD on) (265 hp) Gear 8 (250 hp) Operating Weight 38,320 lb. Work lights Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport lights) Includes 2-high and 2-low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grille, front and rear LED marker lights, LED brake lights AND LED hazard warning lights Blade Width 12 Ft Base Width (8 options available) Blade Height 24" Base Height, up to 27 " w/alternative options Blade Thickness 7/8" Base Thickness, and up to 1" w/alternative options Cutting Edge Size 6" x 5/8" Base, and up to 8" x 3/4" w/alternative options Circle drive slip clutch Optional Numbers of Drive Tires 6 Alternator Size 100 Amp Battery CCA (2) Group 4D Batteries 1400 CCA, 440 reserve minutes each. Seat type Fabric Air Suspension Seat with Armrests and Headrest 3 In., (76 mm) Seat Belt w/retractors (Conforms to SAE J386) 2010 Differential type Fuel Tank Size Rims, Size in Inches/Type Tires Block Heater, Watts Starting Aid Transmission, Speeds Spiral bevel; hydraulically actuated, clutch type can be applied on-the-go; selectable manual or automatic differential lock 110 Gallon In. 12 PR Titan G2 Bias Tires w/ 3 pc. Rims In. 12 PR Titan G2 Bias Tires 120 Volt, 1500 Watts Ether Starting Aid Direct-drive John Deere PowerShift Plus, modulated shift-on-the-go, Event-Based Shifting (EBS), inching pedal; independent transmission reservoir with separate filtration and cooling system with 125- L/min. (33 gpm) gear pump Shift Lever Position km/h (2.5 mph)

32 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 2 of 2 Shift Lever Position km/h (3.5 mph) Shift Lever Position km/h (4.8 mph) Shift Lever Position km/h (6.8 mph) Shift Lever Position km/h (10.2 mph) Shift Lever Position km/h (14.4 mph) Shift Lever Position km/h (20.1 mph) Shift Lever Position km/h (28.3 mph) Forward/Reverse 8 Forward / 8 Reverse (2.5 mph to 28.3 mph) Auto Shift/Manual/Power shift Optional Auto Shift/Manual N/A/Power Shift Standard Heater BTU 31,500 BTU (A/C Standard) Window openings (2) Doors and (2) Left and (2) Right. Front lower and rear sides. Hydraulics Closed-center, pressurecompensated load-sensing (PCLS), variable-displacement piston pump, O-ring face-seal fi ttings Maximum Pump Flow 212 L/min. (56 gpm) Maximum System Pressure kpa (2,750 psi) Pump Displacement 90 cm3 (5.5 cu. in.) Cab Profile/Height Low Profile ROPS Cab, 10' 5" to top of cab Warranty 1 Year Full Machine Warranty BASE PRICE $ 205, John Deere 772G Motor Grader 1.1 BASE MACHINE as stated above. "Included" denotes included in $ 205, BASE PRICE G Grader w/standard Hydraulic Controls GP Grader w/grade Pro EH Controls (Includes finger tip $ 18, controls w/industry standard control pattern, cross slope, Topcon and Trimble ready, return to straight, lever steering and conventional steering wheel) 1.3 Transportation to Monroe Snow & Ice Equipment for Attachment $ 1, Installation 1.4 Transportation to Little Falls Machine, Inc. for Attachment Installation $

33 Qty Price 2.0 OPERATOR STATION Offer operator station options. Number the items starting with 2.1, 2.2, etc., 2.01 Air Conditioning 2.02 Cab Rear Window Electric Defroster Low Cab w/ Fixed Lower Front & Side Windows Low cab w/fixed lower front and side opening windows $ Low Cab w/ Lower Front & Side Opening Windows (Includes roof wiring harness for lighting, beacon, precleaner, and heated mirrors) $ Tall Cab w/ Lower Fixed Front & Side Opening Windows $ Grade Pro Low Cab w/lower Front and Side Opening Windows (Requires 1.2 and 2.12) In Configuration Powered Cab Air Precleaner $ Cab w/o Precleaner Standard Fabric Air Suspension Seat w/armrests and Headrest Premium Heated, Leather/Fabric, High-Wide Back, Air Suspension Seat with Armrests. For use with cab codes 2.03, 2.04, 2.05 & This seat does not include a headrest. $ Grade Pro Premium Heated, Leather/Fabric, High-Wide Back Air Suspension Seat (Requires 1.2 and 2.07) In Configuration to-12 Volt Converter (15 amps) to-12 Volt Converter (30 amps) $ Exterior Mounted Rearview Mirrors Heated Exterior Mounted Rearview Mirrors $ Lower Front Intermittent Wiper & Washer $ Less Lower Front window Wiper & Washer AM/FM Radio with CD and Weather Band (WB) $ No Radio Rear Camera (Provides rear view from dash monitor) $ 1, No Rear Camera Front Window Movable Sun Visor $ Rear Retractable Sun Shade $ Decelerator $ lbs. multi purpose (ABC) Dry Chemical Fire Extinguisher $ Secondary Steering $ 1, ENGINE/POWER TRAIN Offer engine and powertrain options. Number starting with 3.1, 3.2, etc Cool-On-Demand Automatic Reversing Hydraulic Fan 3.02 Fluid Sampling Ports (For sampling engine oil, engine coolant, hydraulic oil, axle & transmission fluids) John Deere PowerTech PSX 9.0L meets EPA IT4 / EU Stage IIIB Emissions (195 Net Peak hp) Standard 100 Amp Alternator amp Alternator $ amp Alternator $ Quick Service Bank for Fluid Changes for Transmission, Hydraulic, Engine Oil, and Engine Coolant (Remote service bank is inside engine compartment and includes Industry Standard Quick Disconnect Couplers) $ No Quick Service Group Standard Fuel & Water Filtration Severe Duty Fuel & Water Filtration System $ Fast Fill Fuel System (150 gpm fill rate) $ 1, No Fast Fill Fuel System Hydraulic Pump Disconnect for Cold Weather Starting $ No Hydraulic Pump Disconnect Engine Exhaust with Flat Black Stack for 9.0L (EPA IT4/EU Stage IIIB only) Engine Exhaust with Chrome Stack for 9.0L (EPA IT4/EU Stage IIIB only) $ Autoshift Transmission $ Manual Shift (No Autoshift) Transmission Transmission Solenoid Valve Guard $ No Transmission Solenoid Valve Group Engine Coolant Circulating Heater, 120 Volt, 1500 Watt Included Ether Starting Aid Included Cold Weather Control Valve Covers (Plastic covers that mount below the cab, shielding the control valve from snow and slowing down hydraulic heat loss in winter. Requires 1.2) $ ELECTRICAL/LIGHTS Offer electrical/light options. Number starting with 4.1, 4.2, etc AT Beacon Strobe kit Installed $ Volt to 12 Volt, 15 Amp Converter w/two outlets 4.03 JDLink Ultimate Machine Monitoring System with 3 Year Message Service Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport Lights) (Includes 2 high and 2 low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grill, front and rear LED marker lights, LED brake lights, and LED hazard warning lights) GRADING LIGHTS (10 HALOGEN LIGHTS) Includes code 4.01 Transporting Halogen w/ LED Signal and Marker Lights, plus (6) Work lights: (2) on bottom of cab, (2) on midframe, and (2) reversing lights on rear grill. $ DELUXE GRADING LIGHTS (16 HALOGEN LIGHTS) NOTE: * Includes code 4.05 Grading Lights plus (6) additional work lights: (4) Corner Cab Work Lights and (2) Front Cab Work Lights.* Requires code amp Altenator or amp Altenator (IT4). $ DELUXE GRADING LIGHTS w/ 2 additional RH Cab Roof Lights (18 HALOGEN LIGHTS) NOTE:* Requires alternator code 3.05 or * Includes code 4.06 Deluxe Grading Lights w/ LED Colored Lights and (2) Additional Rightside Work Lights. $ Two Batteries, Group 4D (1000 CCA, 180 reserve minutes each) $ (47) Two Batteries, Group 4D (1400 CCA, 440 Reserve Minutes Each) Level 1 Electronic Corrosion Prevention Package (Requires 3.19) $ Tall Front Snow Plow Light Bar 26" higher than Standard Frame Lights. Not for use with Mid Mount Scarifier $ Flip Down Cab Beacon Bracket (RH) For Single Beacon on Cab. $ Flip Down Cab Beacon Bracket (LH) $ 56

34 5.0 TIRES/RIMS Offer tire/rim options Number starting with 5.1, 5.2, etc Less Tires & Wheels (NOTE: NOT AVAILABLE FOR UNIT 3R & 48) $ (5,182) In. 12 PR SGG Firestone G2 Bias Tires w/ 3 pc. Rims $ 2, In. 12 PR Titan G2 Bias Tires w/ 3 pc. Rims Included R 24 Inch G2/L2 Single Star XGLA2 Michelin Radial Tires w/ 1 pc. Rims $ 4, R 24 Inch G2/L2 Single Star VUT Bridgestone Radial Tires w/ 1 pc. Rims $ 3, R 24 Inch G2/L2 Single Star XGLA2 Michelin Radial Tires w/ 3 pc. Rims $ 5, R 24 Inch G2/L2 Single Star VUT Bridgestone Radial Tires w/ 3 pc. Rims $ 4, R 24 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 1 pc. Rims $ 6, R 24 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 1 pc. Rims $ 5, R 24 Inch G2/L2 Single Star Snow-plus Michelin Radial Tires w/ 3 pc. Rims $ 7, R 24 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 3 pc. Rims $ 6, In. 12 PR G2/L2 SGG Firestone Bias Tires w/ 3 pc. Rims $ 3, X25 12 ply L2 Goodyear Tires on 3 pc. Rims $ 5, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 1 pc. Rims $ 5, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 1pc. Rims $ 5, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 1 pc. Rims $ 2, R25 L3 Goodyear Radial Tires on 1 pc. Rims $ 12, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 3 pc. Rims $ 7, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 3pc. Rims $ 6, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 3 pc. Rims $ 4, X25 12 ply L2 Goodyear Tires on 3 pc. Rims $ 13, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 1 pc. Rims $ 7, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 3 pc. Rims $ 8, R 25 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 1 pc. Rims $ 8, R 25 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 1 pc. Rims $ 6, R25 Goodyear Snow Tires on 1 pc. Rims $ 10, R 25 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 3 pc. Rims $ 9, R 25 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 3 pc. Rims $ 8, R25 Goodyear Snow Tires on 3 pc. Rims $ 11, /65R25 XLD70 G3/L3 Single Star Michelin Low Profile Radial Tires w/3 pc Rims (Requires code 5.34 No Front Fenders. Can not be used with code 5.35 Rear Fenders.) $ 14, Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 1 pc. Rim $ 3, Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 3 pc. Rim $ 4, Front Fenders $ No Front Fenders Rear Wheel Fenders in.(476mm) Rear Wheel Fenders Fenders are not for use with 550 tires. Fenders can only be used with chains that are designed for 3" of radial clearance and 1.75" of sidewall clearance. Use of Tire chains permitted in accordance with SAE J683, and requires removal of front mud flap on rear fenders. $ 1, HYDRAULICS Offer hydraulic options. Number starting with 6.1, 6.2, etc. Right Hand - Standard Hydraulic Controls Base Hydraulics - 4 Function Controls Requires code 1.1. Base Functions: Rear Steer, Circle Side shift, Wheel Lean & RH Blade Lift w/ Float Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base functions plus 1 function w/float control - front plumbing and hoses for Scarifier or auxiliary applicaton. For Use with Front Scarifier. $ Mid Mount Scarifier Base Hydraulics w/ 1 Auxiliary Function Control Requires Mid Mount Scarifier code and 1.1. Midmount scarifier base hydraulics with 1 auxilliary function control with float control for mid mount scarifier. For use with mid mount scarifier. $ Base Hydraulics w/2 Auxiliary Function Controls Requires code 1.1. Base functions plus 2 functions w/float control - front plumbing and hoses for Scarifier and/or auxiliary application.for Use with Front Scarifier. $ 1, Base Hydraulics w/ 3 Auxiliary Function Controls Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o float control, front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ 2,098 Right Hand - GRADE PRO CONTROLS Finger-tip armrest mounted controls, consistent with the industry standard pattern. Includes armrest Grade Pro Controls for Mid Mount Scarifier w/1 Auxiliary Function Control Requires codes 1.2 and Mid Mount Scarifier code $ Grade Pro Controls with Base Functions NOTE: * Requires code 1.2. * Grade Pro Base Hydraulics Functions: Rear Steer, Circle Side shift, Wheel Lean, Right and Left hand Blade Lift w/ Float, Circle Rotate, Blade Side Shift, Blade Tilt, Lever Steering (also includes steering wheel) In Configuration Grade Pro Controls w/1 Rear Auxiliary Function and Left Hand Lever Controller Requires code 1.2. Base functions plus 1 auxiliary function w/float control - Rear plumbing and hoses for Ripper or auxiliary applicaton. For Use with Rear Ripper. $ Grade Pro Controls w/1 Front Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 FRONT auxiliary function w/float control - front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ Grade Pro Controls w/1 Rear Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 REAR auxiliary function w/float control - front plumbing and hoses for auxiliary application. $ Grade Pro Controls w/1 Front Auxiliary Function and 2 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 3 auxiliary functions- 1 front and 2 rear auxiliary functions w/ float control and rear plumbing for Scarifier / Ripper and/or front, mid $ 2, Grade Pro Controls w/1 Front, 1 Rear Auxiliary Function Control with Right and Left hand Controllers Requires code 1.2. Base Functions plus 2 auxiliary functions - 1 front and 1 rear with float control and plumbing Scarifier / Ripper applications. Auxiliary functions have reconfigurable controls. $ 1, Grade Pro Controls w/1 Front Auxiliary Function and 3 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 4 auxiliary functions - 1 front and 3 rear with float control and plumbing for Scarifier/Ripper and/or front, mid and rear auxiliary applications. Auxiliary functions have reconfigurable controls. $ 3, Grade Pro Controls w/3 Front and 3 Rear Auxiliary Function Controls with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 6 auxiliary functions-3 front and 3 rear with float control on 4 functions, and includes front and rear plumbing for 2 Functions each. Auxiliary functions have reconfigurable controls. $ 4,540 Left Hand - Standard hydraulic Controls

35 Base Hydraulics- 4 Function Controls Requires code 1.1. Base Functions: LH Blade Lift w/ Float, Blade Side shift, Circle Rotate, Blade Tilt Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base Functions plus 1 function w/float control and lines for Ripper or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ Base Hydraulics w/2 Auxiliary Function Control Requires code 1.1. Base functions plus 2 functions w/float control and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 1, Base Hydraulics w/ 3 Auxiliary Function Control Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o Float Control, and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 2, Grade Pro Controls - Left Side NOTE: * Requires code 1.2. * Accompanies GRADE PRO CONTROLS - RIGHT SIDE order code selection. In Configuration Oil, SAE 10W AW46 All Season Hydraulic Oil $ Hydraulic Oil, ISO 46 $ MOLDBOARD/CUTTING EDGE/END BITS/CIRCLE DRIVE Offer these options starting with 7.1, 7.2, 7.3, etc Blade Impact Absorption System Protects Moldboard and draft frame from impacts with Stationary objects $ 1, No Blade Impact Absorption system Ft. x 24 In. x 7/8 In. (3.66 M x 610 mm x 22 mm) with 6 In. x 5/8 In. (152 x 16 mm) Cutting Edge and 5/8 in. (16mm) Hardware Ft. x 24 In. x 7/8 In. (3.66 M x 610 mm x 22 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (3.66 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (3.96 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 24 In. x 7/8 In. (4.27 M x 610 mm x 22 mm) with 6 In. x 5/8 In. (152 x 16 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 24 In. x 7/8 In. (4.27 M x 610 mm x 22 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edgeand 5/8 in. (16mm) Hardware NOTE: Requires engine code $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 3/4 in. (19mm) Hardware Requires engine code $ Extended Life Bronze Wear Inserts NOTE: Recommended for applications in abrasive material. $ Wear Inserts w/o Clutch (Recommended for higher circle torque) Nylon Wear Inserts w/clutch Requires code 7.19 Circle Drive Slip Clutch. Recommended for higher circle torque when used with a slip clutch. $ Reversible Overlay End Bits Not avaible for unit 3R & 48. $ No Reversible Overlay End Bits No Moldboard Extension " 24 in. Left Hand Moldboard Extension Requires Moldboard code 7.08,7.09, or Not available for units 3R & 48. $ 1, " 24 in. Right Hand Moldboard Extension NOTE: * Requires Moldboard code 7.08,7.09, or * Available to all other units with no restrictions. $ 1, Circle Drive with Slip Clutch Protects circle, circle drive gearbox and draft frame from damage when end of moldboard comes in contact with stationary objects. Slip clutch is integral to the circle drive assembly and utilizes a wet clutch system. Can not be used with code 7.04 inserts. $ 1, AT Moldboard Extension, 24 X 24 X 7/8 In. Left Hand 7/8 in. (22mm) thick. Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 24 x 24 x 7/8 In. Right Hand 7/8 in. (22mm) thick. Requires 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 2, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 1, FRONT ATTACHMENTS Offer front attachment options. Starting with 8.1, 8.2, etc. *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & Front Push Block $ 1, Front Scarifier Includes Front Hydraulics, plumbing and hoses Scarifier with 2 pitch positions and 9 shank pockets Five 1 x 3 inch Scarifier Shanks w/teeth If additional shanks are desired order (1) each of T6Y5230 Tooth, T Shank and T Retainer for each set. Can not be used with 6.07 Hydraulics. $ 4, Mid-Mount Scarifier with Integrated Front Push Plate NOTE: * Requires code 6.03 or 6.06 Hydraulics. * Mid-Mount Scarifier with Push Block Can not be used with Front Scarifier. * Not for use with Front Fenders Code * Recommend Rear Counterweight for better machine balance. $ 6, Balderson Style Front Lift Group NOTE: * Requires Hydraulic code 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13, or * (2) AT Mating Hooks from Parts are available to convert old front attachments to the Bladerson-style lift group. $ 3, Less Front Attachment Front-Mounted Dozer Blade, 105 in. x 37.6 in. (2667 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires one of the following 17.5 x 25 tire codes: 5.01, 5.09, 5.11, 5.12, 5.13, 5.15, 5.16, 5.17, 5.19, 5.20, 5.21, 5.22 $ 4, Front-Mounted Dozer Blade, 115 in. x 37.6 in. (2921 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires 550/65R25 tire code: $ 4,704 FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Front Hitch Systems - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Standard Hitch System (Pin-on style hitch. 3.5 double acting lift cylinder with 2 rod.) $ 2,788

36 8.012 Falls Modified 29" Husting Hitch System (Drive -in quick coupler with vertical lift. 3.5 double acting lift cylinder with 2 rod.) $ 3, Falls Modified 34" Husting Hitch System $ 4, Para-Lift Model PLS-1 Hitch System (Drive-in parallel lift quick coupler. $ 3,987 Front Hitch System Options Hydraulic Locking Pin Assembly for Para-Lift Hitch $ Factory Installation of Hydraulic Locking Pin Assy for Para-Lift Hitch $ One Pair Attachment Hooks, Flat Back for Para-Lift Hitch (*Not installed) $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 One Way Snow-Plows Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge, 9'10" Clearing Width w/ Standard Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 29" Husting Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 34" Husting Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Para-Lift Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Scar-a-Lift or Deere Front Mounted Scarifier Coupler $ 8,110 One Way Snow Plow Options Carbide cutting edge, three (3) pc., 3/4 x 6, per foot $112/ft Rubber belt deflector, 3/8 x 12 $ Heavy duty Spring Trip Tilt Bars, add $ Heavy duty Trip Edge Assembly, add $ 1, Hydraulic Moldboard Tilt, replaces rigid or spring trip bars, add $ Steel caster wheel assemblies, add $ 1, Pneumatic caster wheel assemblies, add $ 1, Left hand discharge, add $ Snow Wheel System, add $ 2,023 V-Type Snow Plows - Select the Hitch Attachment Coupler from the Options Falls V-890, 10 gauge A steel moldboard, 10 8 overall width, 9 8 clearing width, 48 nose height, 72 discharge height, three (3) screw-adjustable skid shoes (no tools required), spring loaded snow deflectors $ 6, Falls V-90, 7 gauge A steel moldboard, 12 0 overall width, 9 8 clearing width, 60 nose height, 84 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 6, Falls V-100, 7 gauge A steel moldboard, 13 3 overall width, 10 4 clearing width, 66 nose height, 92 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 8,342 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System $ 1, Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 2, Plow Unit to fit Falls Para-Lift Hitch System w/oscillating feature $ 1, Plow Unit to fit Falls Para-Lift Hitch System (hooks welded solid) $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,360 V-Type Snow Plow Options Spring Loaded Steel Snow Deflectors (Standard on the Falls V-890) $ Rubber Belt Snow Deflector (3/8" x 12") $ Down Pressure Kit for Standard and Modified Husting Hitch Systems $ Snow-Wheel System (In lieu of standard shoes) $ 4,228 Heavy Duty Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options Falls HDR-11, 11' Cutting Edge, 48" High (*Select Hitch from Options) $ 8, Falls HDR-12, 12' Cutting Edge, 48" High (*Select Hitch from Options) $ 8,958 Hitch Attachment Couplers Plow Unit to fit Falls Para-Lift Hitch System $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2, Optional Oscillation Plate (allows plow to follow road contour) $ 1,545 Heavy Duty Reversible Snow Plow Options Carbide Cutting Edge, Add per foot $112//ft Rubber Belt Snow Deflector (3/8" x 12") $ Moldboard Shoes (*Standard Equipment - Not available w/ trip edge assembly) No Charge Screw Adjustable Mushroom Shoes - Set of Two (Can be used with trip edge assembly) $ Trip Edge Assembly (One-piece construction) $ 1,709 Power Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options PR1143 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 6, PR1243 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 7, PR1155/PR1255 Raise moldboard height on PR1143 or PR1243, add to respective snow plow $ TER-11 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6, TER-12 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6,884 Plow-Hitch System Attachment Provides Full Oscillation Left and Right Plow Unit to fit Falls Standard Hitch System $ Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 1, Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,032 Power Reversible Snow Plow Options Trip Edge Assembly $ 1, Carbide Cutting Edge Per Foot $112/ft Rubber Belt Snow Deflector, 3/8" x 12" $ Steel Caster Wheel Assemblies $ 1, Pneumatic Caster Wheel Assemblies $ 1, Curb Shoe, Cylindrical, Each $ Curb Shoe, Wrap-Around, Each $ Snow-Wheel System (In lieu of standard shoes) $ 2,729 Dozer Blades - Select the Hitch Attachment Coupler from the Options

37 8.088 Falls D3696, 8 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36108, 9 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36120, 10 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4,620 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System No Charge Plow Unit to fit Falls Modified 29" Husting Hitch System No Charge Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 1,923 Dozer Blade Options Carbide Cutting Edge, Per Foot $112/ft Scar-A-Lift - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Model FMS-1 Front Mounted Scarifier $ 5,199 Scar-A-Lift Options Scarifier, Head Only, 5 Teeth, No Head Plate or Arms $ 2, Scarifier, Head Only, 5 Teeth, Para-Lift Hooks Installed $ 3, Scarifier Shank, End Bit and Retainer (Each) $ Para-Lift Attachment Hooks, Flat Back, Per Pair $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 HENKE SNOW ATTACHMENTS Henke Fixed Position Dozer Blades DB8 8' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB9 9' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB10 10' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5,348 Lift Group (JRB Installation of Lift Group, Including Freight from Leavenworth STB-STD Scarifier Tool Bar - Lift Group (*Requires hoses to the nose of the motor grader) $ 4, PLG-STD Parallel Lift Group (*Requires hoses to the nose of the motor grader) $ 3, AQC Automatic Quick Coupler Lift Group (*Requires hoses to the nose of the motor grader) $ 5, HSH Henke Universal Hitch for Grader $ 2,596 Attachment Adapter PSS Plow Scarifier Sockets - Mounts to Henke or Factory Scarifier (Specify) $ PLH Parallel Lift Hooks - Mounts to Henke or field "Balderson Style" Lift Group $ AQC Female Attaching Adapter $ 1,367 Henke REL - Heavy Duty Reversible Snow Plow REL 10 10' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 12 12' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 14 14' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 12, REL 16 16' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 13,957 Henke SDDB - Severe Duty Dozer Blade SDDB 10 10' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 12 12' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 14 14' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12, SDDB 16 16' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12,356 Henke HH - Henke Helper Utility Blade HH 8 8' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 9 9' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 10 10' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 8,067 Henke FV - Multi-Directional Folding Vee Snowplow (MDFVS) FV 12 12' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 14, FV 14 14' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 15, FV 16 16' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS ) $ 16,622 Henke Tube Table Power Reversible Snow Plows (Include Grader Adaptor) R11TT 50" Tall, Power Reversible Trip Plow w/tube Table Reversing Frame $ 7, R12TT 50" Tall, Power Reversible Trip Plow w/tube Reversing Frame $ 8,095 Henke Plow Options Mushroom Shoes - Pair $ Install Dealer Supplied Coupler $ Parallel Lift Hook Coupler-Supply/Install $ JRB Style Coupler (Verify size and type) $ Hydraulic Hi-Gate for REL (Includes diverter Kit) $ 6, Trip Lockout Option $ ACS Coupler-Supply/Install $ 1,595 Henke V-Plow

38 8.151 V-9.5 Vee Plow 9.5 Foot Cutting Swath $ 6, V-10 Vee Plow 10 Foot Cutting Swath $ 7, REAR ATTACHMENTS Offer rear attachment options. Starting with 9.1, 9.2, etc No Rear Attachment Rear Mounted Ripper/Scarifier Combination with Rear Hitch and Pin Includes Rear mounted Ripper/Scarifier with rear hitch and pin. NeverGrease Pin Joints. Three 2 x 5 in. Ripper Shanks w/teeth. Can not be used with codes 6.07, 6.09 or $ 8, Rear Counterweight with Rear Hitch and Pin 1600 lbs.(725.7 kg.) Rear Counterweight. Recommend for use with Front / Mid Scarifier. $ 1, Rear Hitch and Pin Not for use with Rear Ripper/Scarifier. $ (9) Extra Scarifier Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ (2) Extra Ripper Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ Slow Moving Vehicle (SMV) Sign Included Handi Hitch *Prices Do Not Include Mounting PP01G Handi Hitch Profile Packer/Roller 90" includes Lift Plate, 24" Packer Offset No Installation Included $ 18, HH01G 870GP Lift Assembly/Offset $ 3, PP04G Profile Accumulator and Hoses $ CR10 Handi Hitch Contour Packer/Roller 75" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR12 Handi Hitch Contour Packer/Roller 90" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR14 Handi Hitch Contour Packer/Roller 105" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 19, CR30 Contour/PP Ripper Shanks $ 1, WR30E Contour Ripper Shank Extender Plates $ CR40 Handi Hitch Contour 24" Packer Offset $ 2, CR50 Handi Hitch Contour Heavy Duty Lift Assembly $ 4, CR55 Handi Hitch Contour Accumulator and Hoses $ CR59 John Deere Link Arms (Lift Assembly) $ SIDE ATTACHMENTS Offer side attachment options. Starting with 10.1, 10.2, etc. FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Wings Falls W12 Wing Only, 12 ft. cutting edge moldboard, 36 height, hydraulic-over-cable controls, rear wing post height is manually adjustable. $ 11, Falls W-14 Wing Only, 14 ft. moldboard cutting edge. $ 12, Falls 2012A Wing Only, 12 ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys, rear wing post height is manually adjustable. $ 12, Falls 2012A Low Post (66" vs 100") $ 12, Falls 2014A Wing Only, 14 ft. moldboard cutting edge. $ 13,090 Invisible Mast Snow Wings (Mast Post Fits Under Cab for Maximum Visibility) IM ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys.invisible Mast post fits under cab allowing maximum visibility. $ 17, IM3014 Same as above w/14' Moldboard $ 17,510 Options for Falls Wings Hydraulic Extendable Buffer Brace $ 2, Hydraulic Elevating Rear Slide $ Trip Edge Assembly for 12 Foot Add $ 1, Trip Edge Assembly for 14 Foot Add $ 1, Left Hand Discharge Add $ Ripper Mount in Lieu of Rear Wing Post and Slide No charge HENKE SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included Price Includes Installation at Factory Wings AHW12FR 12' Grader Wing for Fixed Rear Applications (*Requires 2 valves) $ 11, AHW12MR 12' Grader Wing for Manual Adjusting Rear Applications (*Requires 2 valves) $ 11, AHW12RR 12' Grader Wing for Rear Ripper Applications (*Requires 2 valves) $ 10, AHW12ER 12' Grader Wing for Elevating (Benching) Applications (*Requires 3 valves) $ 12,328 Wing Options ' Grader Moldboard $ Trip Edge Option $ Hi-Gate - Hydraulic End Gate (Includes a diverter kit) $ 4, Factory Installation Wing installation by JRB at the John Deere Factory Included STB-STD Scarifier Tool Bar $ 3, PLG-STD Parallel Lift Group $ 3, AQC Automatic Lift Group $ 4, HSH Henke Standard Hitch (Truck style hitch modified for grader) $ 2, JRB Installation of Lift Group in Davenport Including Freight $ 547 Monroe SNOW ATTACHMENTS (ALL PRICES INCLUDE INSTALLATION AT MONROE) Wings AHW12E-62 for JD "G" Series, 12' All Hydraulic Wing Package w/ 62" Bench Height, 5/8" x 8" Cutting Edge $ 15, AHW12E-38 for JD "G" Series, 12' All Hydraulic Wing Package w/ 38" Bench Height, 5/8" x 8" Cutting Edge $ 15,305 Wing Options Deduct to delete rear post assembly and use ripper-mount bracketry in it's place $ (1,553) Deduct to delete rear post and use 2-position fixed post in it's place $ (1,015) ' Wing Moldboard in Lieu of Standard 12' Model (Requires and/or 10.28) $ Front Lift Group Installed on G-Series Grader $ 5, OTHER ATTACHMENTS Offer other attachment options. Number starting with 11.1, 11.2, etc NS Slopemeter #2 (Installed) $ AT IGC Mast Mounts $ 650 *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & 12.0 EXTENDED WARRANTY OPTIONS Offer performance/warranty options. Number these starting with 12.1, 12.2, etc. (Specify years, miles or hours extended term covers.) Comprehensive (SEE PRICE MATRIX BELOW)

39 12.02 Power Train and Hydraulics (SEE PRICE MATRIX BELOW) Power Train (SEE PRICE MATRIX BELOW) Engine Only (SEE PRICE MATRIX BELOW) Warranty covers John Deere manufactured components only. Standard Manufacturers Warranty applies to all components that are not manufactured by John Deere Extended Powertrain and Hydraulic Warranty has no Deductible per Occurrence after Initial Warranty - See Attached Extended Warranty Sheet Preventative Maintenance Contract (3 Year/2000 Hour) Cost per Hour $ NEW EQUIPMENT RENTAL PROGRAM If rental programs are available on the new equipment offered, with the option to purchase, list the hourly/weekly/monthly rental rate. Indicate the percent of rental fee paid by the purchaser that will be applied to the purchase price. See Solicitation Special Terms & Conditions. Hourly Rental Rate: NA Weekly Rental Rate: $ 2,870 Monthly Rental Rate: $ 8,600 Percent (%) of Rental Fee applied to purchase price: 100%

40 If the new rental equipment is purchased and finance charges are applicable for the actual rental term only, state the actual interest rate here: NA 14 VENDOR OWNED RENTAL RETURN OR DEMO EQUIPMENT PROGRAM See Solicitation Special Terms and Conditions. DEDUCT cost per Used Hour from the original Contract Price $ DISCOUNT OFF LIST PRICE FOR RELATED PARTS & ACCESSORIES 0% (See Special Terms and Conditions) 16 DELIVERY STARTING POINT City, State, Zip Nearest RDO Equipment RDO Equipment Burnsville, MN Grand Forks, ND Moorehead, MN Rochester, MN Marshal, MN N. Mankato, MN Sauk Rapids, MN Sioux Falls, SD NORTRAX Bemidji, MN Duluth, MN Grand Rapids, MN 55744

41 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 1 of 2 Vendor Name: RDO Equipment Company Contact Person: Mike Kluck & Jesse Miller Street Address: DuPont Avenue South P.O. Box: City, State, Zip Burnsville, Minnesota Phone #: Mike: (952) or Jesse: (612) Toll Free #: (800) Fax #: (952) Address: mkluck@rdoequipment.com or jmiller@rdoequipment.com Website: Version of Excel used: Furnish separate price quote for each MOTOR GRADER being offered. 1.1 MOTOR GRADER Make & Model Normal/Variable HP Operating Weight Work lights 2010 John Deere 870G Gear 1 (185 hp) Gear 2 (192 hp) Gear 3 (210 hp) Gear 4 (223 hp) Gear 5 (231 hp) Gear 6 (248 hp) Gear 7 (261 hp) Gear 8 (265 hp) 37,520 lb. Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport lights) Includes 2-high and 2-low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grille, front and rear LED marker lights, LED brake lights AND LED hazard warning lights Blade Width 14 Ft Base Width (5 options available) Blade Height 27" Base Height Blade Thickness 1" Base Thickness Cutting Edge Size 8" x 3/4" Base Circle drive slip clutch Optional Numbers of Drive Tires 4 Alternator Size 100 Amp Battery CCA (2) Group 4D Batteries 1400 CCA, 440 reserve minutes each. Seat type Fabric Air Suspension Seat with Armrests and Headrest 3 In., (76 mm) Seat Belt w/retractors (Conforms to SAE J386) Differential type Fuel Tank Size Rims, Size in Inches/Type Tires Block Heater, Watts Starting Aid Transmission, Speeds Spiral bevel; hydraulically actuated, clutch type can be applied on-the-go; selectable manual or automatic differential lock 110 Gallon 17.5 R 25 Inch L2 w/ 3 pc. Rims 17.5 R 25 Inch L2 Single Star TGD2 Titan Radial Tires 120 Volt, 1500 Watts Ether Starting Aid Direct-drive John Deere PowerShift Plus, modulated shift-on-the-go, Event-Based Shifting (EBS), inching pedal; independent transmission reservoir with separate filtration and cooling system with 125- L/min. (33 gpm) gear pump Shift Lever Position 1 - (2.4 mph) Shift Lever Position 2 - (3.5 mph)

42 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 2 of 2 Shift Lever Position 3 - (4.9 mph) Shift Lever Position 4 - (6.8 mph) Shift Lever Position 5 - (10.4 mph) Shift Lever Position 6 - (14.5 mph) Shift Lever Position 7 - (20.0 mph) Shift Lever Position 8 - (28.0 mph) Forward/Reverse 8 Forward / 8 Reverse (2.5 mph to 28.3 mph) Auto Shift/Manual/Power shift Optional Auto Shift/Manual N/A/Power Shift Standard Heater BTU 31,500 BTU (A/C Standard) Window openings (2) Doors and (2) Left and (2) Right. Front lower and rear sides. Hydraulics Closed-center, pressurecompensated load-sensing (PCLS), variable-displacement piston pump, O-ring face-seal fi ttings Maximum Pump Flow 212 L/min. (56 gpm) Maximum System Pressure kpa (2,750 psi) Pump Displacement 90 cm3 (5.5 cu. in.) Cab Profile/Height Warranty Low Profile ROPS Cab, 10' 5" to top of cab 1 Year Full Machine Warranty BASE PRICE $ 193, John Deere 772G Motor Grader 1.1 BASE MACHINE as stated above. "Included" denotes included in $ 193, BASE PRICE G Grader w/standard Hydraulic Controls GP Grader w/grade Pro EH Controls (Includes finger tip $ 18, controls w/industry standard control pattern, cross slope, Topcon and Trimble ready, return to straight, lever steering and conventional steering wheel) 1.3 Transportation to Monroe Snow & Ice Equipment for Attachment $ 1, Installation 1.4 Transportation to Little Falls Machine, Inc. for Attachment Installation $

43 Qty Price 2.0 OPERATOR STATION Offer operator station options. Number the items starting with 2.1, 2.2, etc., 2.01 Air Conditioning 2.02 Cab Rear Window Electric Defroster Low Cab w/ Fixed Lower Front & Side Windows Low cab w/fixed lower front and side opening windows $ Low Cab w/ Lower Front & Side Opening Windows (Includes roof wiring harness for lighting, beacon, precleaner, and heated mirrors) $ Tall Cab w/ Lower Fixed Front & Side Opening Windows $ Grade Pro Low Cab w/lower Front and Side Opening Windows (Requires 1.2 and 2.12) In Configuration Powered Cab Air Precleaner $ Cab w/o Precleaner Standard Fabric Air Suspension Seat w/armrests and Headrest Premium Heated, Leather/Fabric, High-Wide Back, Air Suspension Seat with Armrests. For use with cab codes 2.03, 2.04, 2.05 & This seat does not include a headrest. $ Grade Pro Premium Heated, Leather/Fabric, High-Wide Back Air Suspension Seat (Requires 1.2 and 2.07) In Configuration to-12 Volt Converter (15 amps) to-12 Volt Converter (30 amps) $ Exterior Mounted Rearview Mirrors Heated Exterior Mounted Rearview Mirrors $ Lower Front Intermittent Wiper & Washer $ Less Lower Front window Wiper & Washer AM/FM Radio with CD and Weather Band (WB) $ No Radio Rear Camera (Provides rear view from dash monitor) $ 1, No Rear Camera Front Window Movable Sun Visor $ Rear Retractable Sun Shade $ Decelerator $ lbs. multi purpose (ABC) Dry Chemical Fire Extinguisher $ Secondary Steering $ 1, ENGINE/POWER TRAIN Offer engine and powertrain options. Number starting with 3.1, 3.2, etc Cool-On-Demand Automatic Reversing Hydraulic Fan 3.02 Fluid Sampling Ports (For sampling engine oil, engine coolant, hydraulic oil, axle & transmission fluids) John Deere PowerTech PSX 9.0L meets EPA IT4 / EU Stage IIIB Emissions (195 Net Peak hp) Standard 100 Amp Alternator amp Alternator $ amp Alternator $ Quick Service Bank for Fluid Changes for Transmission, Hydraulic, Engine Oil, and Engine Coolant (Remote service bank is inside engine compartment and includes Industry Standard Quick Disconnect Couplers) $ No Quick Service Group Standard Fuel & Water Filtration Severe Duty Fuel & Water Filtration System $ Fast Fill Fuel System (150 gpm fill rate) $ 1, No Fast Fill Fuel System Hydraulic Pump Disconnect for Cold Weather Starting $ No Hydraulic Pump Disconnect Engine Exhaust with Flat Black Stack for 9.0L (EPA IT4/EU Stage IIIB only) Engine Exhaust with Chrome Stack for 9.0L (EPA IT4/EU Stage IIIB only) $ Autoshift Transmission $ Manual Shift (No Autoshift) Transmission Transmission Solenoid Valve Guard $ No Transmission Solenoid Valve Group Engine Coolant Circulating Heater, 120 Volt, 1500 Watt Included Ether Starting Aid Included Cold Weather Control Valve Covers (Plastic covers that mount below the cab, shielding the control valve from snow and slowing down hydraulic heat loss in winter. Requires 1.2) $ ELECTRICAL/LIGHTS Offer electrical/light options. Number starting with 4.1, 4.2, etc AT Beacon Strobe kit Installed $ Volt to 12 Volt, 15 Amp Converter w/two outlets 4.03 JDLink Ultimate Machine Monitoring System with 3 Year Message Service Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport Lights) (Includes 2 high and 2 low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grill, front and rear LED marker lights, LED brake lights, and LED hazard warning lights) GRADING LIGHTS (10 HALOGEN LIGHTS) Includes code 4.01 Transporting Halogen w/ LED Signal and Marker Lights, plus (6) Work lights: (2) on bottom of cab, (2) on midframe, and (2) reversing lights on rear grill. $ DELUXE GRADING LIGHTS (16 HALOGEN LIGHTS) NOTE: * Includes code 4.05 Grading Lights plus (6) additional work lights: (4) Corner Cab Work Lights and (2) Front Cab Work Lights.* Requires code amp Altenator or amp Altenator (IT4). $ DELUXE GRADING LIGHTS w/ 2 additional RH Cab Roof Lights (18 HALOGEN LIGHTS) NOTE:* Requires alternator code 3.05 or * Includes code 4.06 Deluxe Grading Lights w/ LED Colored Lights and (2) Additional Rightside Work Lights. $ Two Batteries, Group 4D (1000 CCA, 180 reserve minutes each) $ (47) Two Batteries, Group 4D (1400 CCA, 440 Reserve Minutes Each) Level 1 Electronic Corrosion Prevention Package (Requires 3.19) $ Tall Front Snow Plow Light Bar 26" higher than Standard Frame Lights. Not for use with Mid Mount Scarifier $ Flip Down Cab Beacon Bracket (RH) For Single Beacon on Cab. $ Flip Down Cab Beacon Bracket (LH) $ 56

44 5.0 TIRES/RIMS Offer tire/rim options Number starting with 5.1, 5.2, etc Less Tires & Wheels (NOTE: NOT AVAILABLE FOR UNIT 3R & 48) $ (9,268) R 24 Inch G2/L2 Single Star Snow-plus Michelin Radial Tires w/ 3 pc. Rims $ 3, R 24 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 3 pc. Rims $ 2, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 3 pc. Rims $ 3, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 3pc. Rims $ 2, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 3 pc. Rims Included X25 12 ply L2 Goodyear Tires on 3 pc. Rims $ 9, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 3 pc. Rims $ 4, R 25 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 3 pc. Rims $ 5, R 25 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 3 pc. Rims $ 4, R25 Goodyear Snow Tires on 3 pc. Rims $ 7, /65R25 XLD70 G3/L3 Single Star Michelin Low Profile Radial Tires w/3 pc Rims (Requires code 5.28 No Front Fenders. Can not be used with code 5.29 Rear Fenders.) $ 10, Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 1 pc. Rim $ 3, Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 3 pc. Rim $ 4, Front Fenders $ No Front Fenders Rear Wheel Fenders in.(476mm) Rear Wheel Fenders Fenders are not for use with 550 tires. Fenders can only be used with chains that are designed for 3" of radial clearance and 1.75" of sidewall clearance. Use of Tire chains permitted in accordance with SAE J683, and requires removal of front mud flap on rear fenders. $ 1, HYDRAULICS Offer hydraulic options. Number starting with 6.1, 6.2, etc. Right Hand - Standard Hydraulic Controls Base Hydraulics - 4 Function Controls Requires code 1.1. Base Functions: Rear Steer, Circle Side shift, Wheel Lean & RH Blade Lift w/ Float Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base functions plus 1 function w/float control - front plumbing and hoses for Scarifier or auxiliary applicaton. For Use with Front Scarifier. $ Mid Mount Scarifier Base Hydraulics w/ 1 Auxiliary Function Control Requires Mid Mount Scarifier code and 1.1. Midmount scarifier base hydraulics with 1 auxilliary function control with float control for mid mount scarifier. For use with mid mount scarifier. $ Base Hydraulics w/2 Auxiliary Function Controls Requires code 1.1. Base functions plus 2 functions w/float control - front plumbing and hoses for Scarifier and/or auxiliary application.for Use with Front Scarifier. $ 1, Base Hydraulics w/ 3 Auxiliary Function Controls Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o float control, front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ 2,098 Right Hand - GRADE PRO CONTROLS Finger-tip armrest mounted controls, consistent with the industry standard pattern. Includes armrest Grade Pro Controls for Mid Mount Scarifier w/1 Auxiliary Function Control Requires codes 1.2 and Mid Mount Scarifier code $ Grade Pro Controls with Base Functions NOTE: * Requires code 1.2. * Grade Pro Base Hydraulics Functions: Rear Steer, Circle Side shift, Wheel Lean, Right and Left hand Blade Lift w/ Float, Circle Rotate, Blade Side Shift, Blade Tilt, Lever Steering (also includes steering wheel) In Configuration Grade Pro Controls w/1 Rear Auxiliary Function and Left Hand Lever Controller Requires code 1.2. Base functions plus 1 auxiliary function w/float control - Rear plumbing 6.09 and 6560 hoses Grade for Pro Ripper Controls or auxiliary w/1 Front applicaton. Auxiliary For Function Use with Control Rear and Ripper. Right Hand Lever $ 757 Controller Requires code 1.2. Base functions plus 1 FRONT auxiliary function w/float control - front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ Grade Pro Controls w/1 Rear Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 REAR auxiliary function w/float control - front plumbing and hoses for auxiliary application. $ Grade Pro Controls w/1 Front Auxiliary Function and 2 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 3 auxiliary functions- 1 front and 2 rear auxiliary functions w/ float control and rear plumbing for Scarifier / Ripper and/or front, mid $ 2, Grade Pro Controls w/1 Front, 1 Rear Auxiliary Function Control with Right and Left hand Controllers Requires code 1.2. Base Functions plus 2 auxiliary functions - 1 front and 1 rear with float control and plumbing Scarifier / Ripper applications. Auxiliary functions have reconfigurable controls. $ 1, Grade Pro Controls w/1 Front Auxiliary Function and 3 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 4 auxiliary functions - 1 front and 3 rear with float control and plumbing for Scarifier/Ripper and/or front, mid and rear auxiliary applications. Auxiliary functions have reconfigurable controls. $ 3, Grade Pro Controls w/3 Front and 3 Rear Auxiliary Function Controls with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 6 auxiliary functions-3 front and 3 rear with float control on 4 functions, and includes front and rear plumbing for 2 Functions each. Auxiliary functions have reconfigurable controls. $ 4,540 Left Hand - Standard hydraulic Controls Base Hydraulics- 4 Function Controls Requires code 1.1. Base Functions: LH Blade Lift w/ Float, Blade Side shift, Circle Rotate, Blade Tilt Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base Functions plus 1 function w/float control and lines for Ripper or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ Base Hydraulics w/2 Auxiliary Function Control Requires code 1.1. Base functions plus 2 functions w/float control and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 1, Base Hydraulics w/ 3 Auxiliary Function Control Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o Float Control, and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 2, Grade Pro Controls - Left Side NOTE: * Requires code 1.2. * Accompanies GRADE PRO CONTROLS - RIGHT SIDE order code selection. In Configuration Oil, SAE 10W AW46 All Season Hydraulic Oil $ Hydraulic Oil, ISO 46 $ MOLDBOARD/CUTTING EDGE/END BITS/CIRCLE DRIVE

45 Offer these options starting with 7.1, 7.2, 7.3, etc Blade Impact Absorption System Protects Moldboard and draft frame from impacts with Stationary objects $ 1, No Blade Impact Absorption system Ft. x 27 In. x 1 In. (3.66 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ (297) Ft. x 27 In. x 1 In. (3.96 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edgeand 5/8 in. (16mm) Hardware NOTE: Requires engine code $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 3/4 in. (19mm) Hardware Requires engine code $ Ft. x 27 In. x 1 In. (4.88 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 3/4 in. (19mm) Hardware Requires code 7.19 Slip Clutch, 7.12 Wear Inserts and 7.16 Extensions. $ Extended Life Bronze Wear Inserts NOTE: Recommended for applications in abrasive material. $ Wear Inserts w/o Clutch (Recommended for higher circle torque) Nylon Wear Inserts w/clutch Requires code 7.19 Circle Drive Slip Clutch. Recommended for higher circle torque when used with a slip clutch. $ Reversible Overlay End Bits Not avaible for unit 3R & 48. $ No Reversible Overlay End Bits No Moldboard Extension " 24 in. Left Hand Moldboard Extension Requires Moldboard code 7.05, or $ 1, " 24 in. Right Hand Moldboard Extension NOTE: * * Requires Moldboard code 7.05, or $ 1, Circle Drive with Slip Clutch Protects circle, circle drive gearbox and draft frame from damage when end of moldboard comes in contact with stationary objects. Slip clutch is integral to the circle drive assembly and utilizes a wet clutch system. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 2, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 1, FRONT ATTACHMENTS Offer front attachment options. Starting with 8.1, 8.2, etc. *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & Front Push Block $ 1, Front Scarifier Includes Front Hydraulics, plumbing and hoses Scarifier with 2 pitch positions and 9 shank pockets Five 1 x 3 inch Scarifier Shanks w/teeth If additional shanks are desired order (1) each of T6Y5230 Tooth, T Shank and T Retainer for each set. Can not be used with 6.07 Hydraulics. $ 4, Mid-Mount Scarifier with Integrated Front Push Plate NOTE: * Requires code 6.03 or 6.06 Hydraulics. * Mid-Mount Scarifier with Push Block Can not be used with Front Scarifier. * Not for use with Front Fenders Code * Recommend Rear Counterweight for better machine balance. $ 6, Balderson Style Front Lift Group NOTE: * Requires Hydraulic code 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13, or * (2) AT Mating Hooks from Parts are available to convert old front attachments to the Bladerson-style lift group. $ 3, Less Front Attachment Front-Mounted Dozer Blade, 105 in. x 37.6 in. (2667 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires one of the following 17.5 x 25 tire codes: 5.01, 5.09, 5.11, 5.12, 5.13, 5.15, 5.16, 5.17, 5.19, 5.20, 5.21, 5.22 $ 4, Front-Mounted Dozer Blade, 115 in. x 37.6 in. (2921 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires 550/65R25 tire code: $ 4,704 FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Front Hitch Systems - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Standard Hitch System (Pin-on style hitch. 3.5 double acting lift cylinder with 2 rod.) $ 2, Falls Modified 29" Husting Hitch System (Drive -in quick coupler with vertical lift. 3.5 double acting lift cylinder with 2 rod.) $ 3, Falls Modified 34" Husting Hitch System $ 4, Para-Lift Model PLS-1 Hitch System (Drive-in parallel lift quick coupler. $ 3,987 Front Hitch System Options Hydraulic Locking Pin Assembly for Para-Lift Hitch $ Factory Installation of Hydraulic Locking Pin Assy for Para-Lift Hitch $ One Pair Attachment Hooks, Flat Back for Para-Lift Hitch (*Not installed) $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 One Way Snow-Plows Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge, 9'10" Clearing Width w/ Standard Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 29" Husting Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 34" Husting Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Para-Lift Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Scar-a-Lift or Deere Front Mounted Scarifier Coupler $ 8,110 One Way Snow Plow Options Carbide cutting edge, three (3) pc., 3/4 x 6, per foot $112/ft Rubber belt deflector, 3/8 x 12 $ Heavy duty Spring Trip Tilt Bars, add $ Heavy duty Trip Edge Assembly, add $ 1, Hydraulic Moldboard Tilt, replaces rigid or spring trip bars, add $ Steel caster wheel assemblies, add $ 1, Pneumatic caster wheel assemblies, add $ 1, Left hand discharge, add $ Snow Wheel System, add $ 2,023

46 V-Type Snow Plows - Select the Hitch Attachment Coupler from the Options Falls V-890, 10 gauge A steel moldboard, 10 8 overall width, 9 8 clearing width, 48 nose height, 72 discharge height, three (3) screw-adjustable skid shoes (no tools required), spring loaded snow deflectors $ 6, Falls V-90, 7 gauge A steel moldboard, 12 0 overall width, 9 8 clearing width, 60 nose height, 84 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 6, Falls V-100, 7 gauge A steel moldboard, 13 3 overall width, 10 4 clearing width, 66 nose height, 92 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 8,342 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System $ 1, Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 2, Plow Unit to fit Falls Para-Lift Hitch System w/oscillating feature $ 1, Plow Unit to fit Falls Para-Lift Hitch System (hooks welded solid) $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,360 V-Type Snow Plow Options Spring Loaded Steel Snow Deflectors (Standard on the Falls V-890) $ Rubber Belt Snow Deflector (3/8" x 12") $ Down Pressure Kit for Standard and Modified Husting Hitch Systems $ Snow-Wheel System (In lieu of standard shoes) $ 4,228 Heavy Duty Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options Falls HDR-11, 11' Cutting Edge, 48" High (*Select Hitch from Options) $ 8, Falls HDR-12, 12' Cutting Edge, 48" High (*Select Hitch from Options) $ 8,958 Hitch Attachment Couplers Plow Unit to fit Falls Para-Lift Hitch System $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2, Optional Oscillation Plate (allows plow to follow road contour) $ 1,545 Heavy Duty Reversible Snow Plow Options Carbide Cutting Edge, Add per foot $112//ft Rubber Belt Snow Deflector (3/8" x 12") $ Moldboard Shoes (*Standard Equipment - Not available w/ trip edge assembly) No Charge Screw Adjustable Mushroom Shoes - Set of Two (Can be used with trip edge assembly) $ Trip Edge Assembly (One-piece construction) $ 1,709 Power Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options PR1143 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 6, PR1243 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 7, PR1155/PR1255 Raise moldboard height on PR1143 or PR1243, add to respective snow plow $ TER-11 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6, TER-12 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6,884 Plow-Hitch System Attachment Provides Full Oscillation Left and Right Plow Unit to fit Falls Standard Hitch System $ Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 1, Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,032 Power Reversible Snow Plow Options Trip Edge Assembly $ 1, Carbide Cutting Edge Per Foot $112/ft Rubber Belt Snow Deflector, 3/8" x 12" $ Steel Caster Wheel Assemblies $ 1, Pneumatic Caster Wheel Assemblies $ 1, Curb Shoe, Cylindrical, Each $ Curb Shoe, Wrap-Around, Each $ Snow-Wheel System (In lieu of standard shoes) $ 2,729 Dozer Blades - Select the Hitch Attachment Coupler from the Options Falls D3696, 8 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36108, 9 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36120, 10 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4,620 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System No Charge Plow Unit to fit Falls Modified 29" Husting Hitch System No Charge Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 1,923 Dozer Blade Options Carbide Cutting Edge, Per Foot $112/ft Scar-A-Lift - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Model FMS-1 Front Mounted Scarifier $ 5,199 Scar-A-Lift Options Scarifier, Head Only, 5 Teeth, No Head Plate or Arms $ 2, Scarifier, Head Only, 5 Teeth, Para-Lift Hooks Installed $ 3, Scarifier Shank, End Bit and Retainer (Each) $ Para-Lift Attachment Hooks, Flat Back, Per Pair $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 HENKE SNOW ATTACHMENTS Henke Fixed Position Dozer Blades DB8 8' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB9 9' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB10 10' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5,348 Lift Group (JRB Installation of Lift Group, Including Freight from Leavenworth

47 8.113 STB-STD Scarifier Tool Bar - Lift Group (*Requires hoses to the nose of the motor grader) $ 4, PLG-STD Parallel Lift Group (*Requires hoses to the nose of the motor grader) $ 3, AQC Automatic Quick Coupler Lift Group (*Requires hoses to the nose of the motor grader) $ 5, HSH Henke Universal Hitch for Grader $ 2,596 Attachment Adapter PSS Plow Scarifier Sockets - Mounts to Henke or Factory Scarifier (Specify) $ PLH Parallel Lift Hooks - Mounts to Henke or field "Balderson Style" Lift Group $ AQC Female Attaching Adapter $ 1,367 Henke REL - Heavy Duty Reversible Snow Plow REL 10 10' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 12 12' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 14 14' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 12, REL 16 16' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 13,957 Henke SDDB - Severe Duty Dozer Blade SDDB 10 10' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 12 12' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 14 14' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12, SDDB 16 16' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12,356 Henke HH - Henke Helper Utility Blade HH 8 8' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 9 9' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 10 10' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 8,067 Henke FV - Multi-Directional Folding Vee Snowplow (MDFVS) FV 12 12' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 14, FV 14 14' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 15, FV 16 16' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS ) $ 16,622 Henke Tube Table Power Reversible Snow Plows (Include Grader Adaptor) R11TT 50" Tall, Power Reversible Trip Plow w/tube Table Reversing Frame $ 7, R12TT 50" Tall, Power Reversible Trip Plow w/tube Reversing Frame $ 8,095 Henke Plow Options Mushroom Shoes - Pair $ Install Dealer Supplied Coupler $ Parallel Lift Hook Coupler-Supply/Install $ JRB Style Coupler (Verify size and type) $ Hydraulic Hi-Gate for REL (Includes diverter Kit) $ 6, Trip Lockout Option $ ACS Coupler-Supply/Install $ 1,595 Henke V-Plow V-9.5 Vee Plow 9.5 Foot Cutting Swath $ 6, V-10 Vee Plow 10 Foot Cutting Swath $ 7, REAR ATTACHMENTS Offer rear attachment options. Starting with 9.1, 9.2, etc No Rear Attachment Rear Mounted Ripper/Scarifier Combination with Rear Hitch and Pin Includes Rear mounted Ripper/Scarifier with rear hitch and pin. NeverGrease Pin Joints. Three 2 x 5 in. Ripper Shanks w/teeth. Can not be used with codes 6.07, 6.09 or $ 8, Rear Counterweight with Rear Hitch and Pin 1600 lbs.(725.7 kg.) Rear Counterweight. Recommend for use with Front / Mid Scarifier. $ 1, Rear Hitch and Pin Not for use with Rear Ripper/Scarifier. $ (9) Extra Scarifier Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ (2) Extra Ripper Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ Slow Moving Vehicle (SMV) Sign Included Handi Hitch *Prices Do Not Include Mounting PP01G Handi Hitch Profile Packer/Roller 90" includes Lift Plate, 24" Packer Offset No Installation Included $ 18, HH01G 870GP Lift Assembly/Offset $ 3, PP04G Profile Accumulator and Hoses $ CR10 Handi Hitch Contour Packer/Roller 75" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR12 Handi Hitch Contour Packer/Roller 90" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR14 Handi Hitch Contour Packer/Roller 105" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 19, CR30 Contour/PP Ripper Shanks $ 1, WR30E Contour Ripper Shank Extender Plates $ 759

48 CR40 Handi Hitch Contour 24" Packer Offset $ 2, CR50 Handi Hitch Contour Heavy Duty Lift Assembly $ 4, CR55 Handi Hitch Contour Accumulator and Hoses $ CR59 John Deere Link Arms (Lift Assembly) $ SIDE ATTACHMENTS Offer side attachment options. Starting with 10.1, 10.2, etc. FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Wings Falls W12 Wing Only, 12 ft. cutting edge moldboard, 36 height, hydraulic-over-cable controls, rear wing post height is manually adjustable. $ 11, Falls W-14 Wing Only, 14 ft. moldboard cutting edge. $ 12, Falls 2012A Wing Only, 12 ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys, rear wing post height is manually adjustable. $ 12, Falls 2012A Low Post (66" vs 100") $ 12, Falls 2014A Wing Only, 14 ft. moldboard cutting edge. $ 13,090 Invisible Mast Snow Wings (Mast Post Fits Under Cab for Maximum Visibility) IM ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys.invisible Mast post fits under cab allowing maximum visibility. $ 17, IM3014 Same as above w/14' Moldboard $ 17,510 Options for Falls Wings Hydraulic Extendable Buffer Brace $ 2, Hydraulic Elevating Rear Slide $ Trip Edge Assembly for 12 Foot Add $ 1, Trip Edge Assembly for 14 Foot Add $ 1, Left Hand Discharge Add $ Ripper Mount in Lieu of Rear Wing Post and Slide No charge HENKE SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included Price Includes Installation at Factory Wings AHW12FR 12' Grader Wing for Fixed Rear Applications (*Requires 2 valves) $ 11, AHW12MR 12' Grader Wing for Manual Adjusting Rear Applications (*Requires 2 valves) $ 11, AHW12RR 12' Grader Wing for Rear Ripper Applications (*Requires 2 valves) $ 10, AHW12ER 12' Grader Wing for Elevating (Benching) Applications (*Requires 3 valves) $ 12,328 Wing Options ' Grader Moldboard $ Trip Edge Option $ Hi-Gate - Hydraulic End Gate (Includes a diverter kit) $ 4, Factory Installation Wing installation by JRB at the John Deere Factory Included STB-STD Scarifier Tool Bar $ 3, PLG-STD Parallel Lift Group $ 3, AQC Automatic Lift Group $ 4, HSH Henke Standard Hitch (Truck style hitch modified for grader) $ 2, JRB Installation of Lift Group in Davenport Including Freight $ 547 Monroe SNOW ATTACHMENTS (ALL PRICES INCLUDE INSTALLATION AT MONROE) Wings AHW12E-62 for JD "G" Series, 12' All Hydraulic Wing Package w/ 62" Bench Height, 5/8" x 8" Cutting Edge $ 15, AHW12E-38 for JD "G" Series, 12' All Hydraulic Wing Package w/ 38" Bench Height, 5/8" x 8" Cutting Edge $ 15,305 Wing Options Deduct to delete rear post assembly and use ripper-mount bracketry in it's place $ (1,553) Deduct to delete rear post and use 2-position fixed post in it's place $ (1,015) ' Wing Moldboard in Lieu of Standard 12' Model (Requires and/or 10.28) $ Front Lift Group Installed on G-Series Grader $ 5, OTHER ATTACHMENTS Offer other attachment options. Number starting with 11.1, 11.2, etc NS Slopemeter #2 (Installed) $ AT IGC Mast Mounts $ 650 *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & 12.0 EXTENDED WARRANTY OPTIONS Offer performance/warranty options. Number these starting with 12.1, 12.2, etc. (Specify years, miles or hours extended term covers.) Comprehensive (SEE PRICE MATRIX BELOW) Power Train and Hydraulics (SEE PRICE MATRIX BELOW)

49 12.03 Power Train (SEE PRICE MATRIX BELOW) Engine Only (SEE PRICE MATRIX BELOW) Warranty covers John Deere manufactured components only. Standard Manufacturers Warranty applies to all components that are not manufactured by John Deere Extended Powertrain and Hydraulic Warranty has no Deductible per Occurrence after Initial Warranty - See Attached Extended Warranty Sheet Preventative Maintenance Contract (3 Year/2000 Hour) Cost per Hour $ NEW EQUIPMENT RENTAL PROGRAM If rental programs are available on the new equipment offered, with the option to purchase, list the hourly/weekly/monthly rental rate. Indicate the percent of rental fee paid by the purchaser that will be applied to the purchase price. See Solicitation Special Terms & Conditions. Hourly Rental Rate: NA Weekly Rental Rate: $ 2,670 Monthly Rental Rate: $ 8,000 Percent (%) of Rental Fee applied to purchase price: 100% If the new rental equipment is purchased and finance charges are applicable for the actual rental term only, state the actual interest rate here: NA 14 VENDOR OWNED RENTAL RETURN OR DEMO EQUIPMENT PROGRAM See Solicitation Special Terms and Conditions. DEDUCT cost per Used Hour from the original Contract Price $ DISCOUNT OFF LIST PRICE FOR RELATED PARTS & ACCESSORIES 0% (See Special Terms and Conditions) 16 DELIVERY STARTING POINT City, State, Zip Nearest RDO Equipment RDO Equipment Burnsville, MN Moorehead, MN Grand Forks, ND Rochester, MN Marshal, MN 56258

50 N. Mankato, MN Sauk Rapids, MN Sioux Falls, SD NORTRAX Bemidji, MN Duluth, MN Grand Rapids, MN DELIVERY PRICE PER LOADED MILE No Flat Rate Allowed- See Special Terms and Conditions $6.00 w/$300 Minimum

51 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 1 of 2 Vendor Name: RDO Equipment Company Contact Person: Mike Kluck & Jesse Miller Street Address: DuPont Avenue South P.O. Box: City, State, Zip Burnsville, Minnesota Phone #: Mike: (952) or Jesse: (612) Toll Free #: (800) Fax #: (952) Address: mkluck@rdoequipment.com or jmiller@rdoequipment.com Website: Version of Excel used: Furnish separate price quote for each MOTOR GRADER being offered. 1.1 MOTOR GRADER Make & Model John Deere 872G Normal/Variable HP Gear 1 (6WD on) (221 hp) Gear 2 (6WD on) (227 hp) Gear 3 (6WD on) (241 hp) Gear 4 (6WD on) (249 hp) Gear 5 (6WD on) (259 hp) Gear 6 (6WD on) (273 hp) Gear 7 (6WD on) (283 hp) Gear 8 (273 hp) Operating Weight 39,650 lb. Work lights Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport lights) Includes 2-high and 2-low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grille, front and rear LED marker lights, LED brake lights AND LED hazard warning lights Blade Width 14 Ft Base Width (5 options available) Blade Height 27" Base Height Blade Thickness 1" Base Thickness Cutting Edge Size 8" x 3/4" Base Circle drive slip clutch Optional Numbers of Drive Tires 6 Alternator Size 100 Amp Battery CCA (2) Group 4D Batteries 1400 CCA, 440 reserve minutes each. Seat type Fabric Air Suspension Seat with Armrests and Headrest 3 In., (76 mm) Seat Belt w/retractors (Conforms to SAE J386) 2010 Differential type Fuel Tank Size Rims, Size in Inches/Type Tires Block Heater, Watts Starting Aid Transmission, Speeds Spiral bevel; hydraulically actuated, clutch type can be applied on-the-go; selectable manual or automatic differential lock 110 Gallon 17.5 R 25 Inch L2 w/ 3 pc. Rims 17.5 R 25 Inch L2 Single Star TGD2 Titan Radial Tires 120 Volt, 1500 Watts Ether Starting Aid Direct-drive John Deere PowerShift Plus, modulated shift-on-the-go, Event-Based Shifting (EBS), inching pedal; independent transmission reservoir with separate filtration and cooling system with 125- L/min. (33 gpm) gear pump Shift Lever Position 1 (2.4 mph) Shift Lever Position 2 (3.5 mph)

52 SEQ. # MOTOR GRADERS (5) PRICING PAGES (Typed responses required) Page 2 of 2 Shift Lever Position 3 (4.9 mph) Shift Lever Position 4 (6.8 mph) Shift Lever Position 5 (10.4 mph) Shift Lever Position 6 (14.5 mph) Shift Lever Position 7 (20.0 mph) Shift Lever Position 8 (28.0 mph) Forward/Reverse 8 Forward / 8 Reverse (2.5 mph to 28.3 mph) Auto Shift/Manual/Power shift Optional Auto Shift/Manual N/A/Power Shift Standard Heater BTU 31,500 BTU (A/C Standard) Window openings (2) Doors and (2) Left and (2) Right. Front lower and rear sides. Hydraulics Closed-center, pressurecompensated load-sensing (PCLS), variable-displacement piston pump, O-ring face-seal fi ttings Maximum Pump Flow 212 L/min. (56 gpm) Maximum System Pressure kpa (2,750 psi) Pump Displacement 90 cm3 (5.5 cu. in.) Cab Profile/Height Low Profile ROPS Cab, 10' 5" to top of cab Warranty 1 Year Full Machine Warranty BASE PRICE $ 237, John Deere 772G Motor Grader 1.1 BASE MACHINE as stated above. "Included" denotes included in $ 237, BASE PRICE G Grader w/standard Hydraulic Controls GP Grader w/grade Pro EH Controls (Includes finger tip $ 18, controls w/industry standard control pattern, cross slope, Topcon and Trimble ready, return to straight, lever steering and conventional steering wheel) 1.3 Transportation to Monroe Snow & Ice Equipment for Attachment $ 1, Installation 1.4 Transportation to Little Falls Machine, Inc. for Attachment Installation $

53 Qty Price 2.0 OPERATOR STATION Offer operator station options. Number the items starting with 2.1, 2.2, etc., 2.01 Air Conditioning 2.02 Cab Rear Window Electric Defroster Low Cab w/ Fixed Lower Front & Side Windows Low cab w/fixed lower front and side opening windows $ Low Cab w/ Lower Front & Side Opening Windows (Includes roof wiring harness for lighting, beacon, precleaner, and heated mirrors) $ Tall Cab w/ Lower Fixed Front & Side Opening Windows $ Grade Pro Low Cab w/lower Front and Side Opening Windows (Requires 1.2 and 2.12) In Configuration Powered Cab Air Precleaner $ Cab w/o Precleaner Standard Fabric Air Suspension Seat w/armrests and Headrest Premium Heated, Leather/Fabric, High-Wide Back, Air Suspension Seat with Armrests. For use with cab codes 2.03, 2.04, 2.05 & This seat does not include a headrest. $ Grade Pro Premium Heated, Leather/Fabric, High-Wide Back Air Suspension Seat (Requires 1.2 and 2.07) In Configuration to-12 Volt Converter (15 amps) to-12 Volt Converter (30 amps) $ Exterior Mounted Rearview Mirrors Heated Exterior Mounted Rearview Mirrors $ Lower Front Intermittent Wiper & Washer $ Less Lower Front window Wiper & Washer AM/FM Radio with CD and Weather Band (WB) $ No Radio Rear Camera (Provides rear view from dash monitor) $ 1, No Rear Camera Front Window Movable Sun Visor $ Rear Retractable Sun Shade $ Decelerator $ lbs. multi purpose (ABC) Dry Chemical Fire Extinguisher $ Secondary Steering $ 1, ENGINE/POWER TRAIN Offer engine and powertrain options. Number starting with 3.1, 3.2, etc Cool-On-Demand Automatic Reversing Hydraulic Fan 3.02 Fluid Sampling Ports (For sampling engine oil, engine coolant, hydraulic oil, axle & transmission fluids) John Deere PowerTech PSX 9.0L meets EPA IT4 / EU Stage IIIB Emissions (195 Net Peak hp) Standard 100 Amp Alternator amp Alternator $ amp Alternator $ Quick Service Bank for Fluid Changes for Transmission, Hydraulic, Engine Oil, and Engine Coolant (Remote service bank is inside engine compartment and includes Industry Standard Quick Disconnect Couplers) $ No Quick Service Group Standard Fuel & Water Filtration Severe Duty Fuel & Water Filtration System $ Fast Fill Fuel System (150 gpm fill rate) $ 1, No Fast Fill Fuel System Hydraulic Pump Disconnect for Cold Weather Starting $ No Hydraulic Pump Disconnect Engine Exhaust with Flat Black Stack for 9.0L (EPA IT4/EU Stage IIIB only) Engine Exhaust with Chrome Stack for 9.0L (EPA IT4/EU Stage IIIB only) $ Autoshift Transmission $ Manual Shift (No Autoshift) Transmission Transmission Solenoid Valve Guard $ No Transmission Solenoid Valve Group Engine Coolant Circulating Heater, 120 Volt, 1500 Watt Included Ether Starting Aid Included Cold Weather Control Valve Covers (Plastic covers that mount below the cab, shielding the control valve from snow and slowing down hydraulic heat loss in winter. Requires 1.2) $ ELECTRICAL/LIGHTS Offer electrical/light options. Number starting with 4.1, 4.2, etc AT Beacon Strobe kit Installed $ Volt to 12 Volt, 15 Amp Converter w/two outlets 4.03 JDLink Ultimate Machine Monitoring System with 3 Year Message Service Transporting Lights w/led Signal and Marker Lights (4 Halogen Transport Lights) (Includes 2 high and 2 low beam halogen headlights with LED turn signals on bar, LED rear turn signals mounted on rear grill, front and rear LED marker lights, LED brake lights, and LED hazard warning lights) GRADING LIGHTS (10 HALOGEN LIGHTS) Includes code 4.01 Transporting Halogen w/ LED Signal and Marker Lights, plus (6) Work lights: (2) on bottom of cab, (2) on midframe, and (2) reversing lights on rear grill. $ DELUXE GRADING LIGHTS (16 HALOGEN LIGHTS) NOTE: * Includes code 4.05 Grading Lights plus (6) additional work lights: (4) Corner Cab Work Lights and (2) Front Cab Work Lights.* Requires code amp Altenator or amp Altenator (IT4). $ DELUXE GRADING LIGHTS w/ 2 additional RH Cab Roof Lights (18 HALOGEN LIGHTS) NOTE:* Requires alternator code 3.05 or * Includes code 4.06 Deluxe Grading Lights w/ LED Colored Lights and (2) Additional Rightside Work Lights. $ Two Batteries, Group 4D (1000 CCA, 180 reserve minutes each) $ (47) Two Batteries, Group 4D (1400 CCA, 440 Reserve Minutes Each) Level 1 Electronic Corrosion Prevention Package (Requires 3.19) $ Tall Front Snow Plow Light Bar 26" higher than Standard Frame Lights. Not for use with Mid Mount Scarifier $ Flip Down Cab Beacon Bracket (RH) For Single Beacon on Cab. $ Flip Down Cab Beacon Bracket (LH) $ 56

54 5.0 TIRES/RIMS Offer tire/rim options Number starting with 5.1, 5.2, etc Less Tires & Wheels (NOTE: NOT AVAILABLE FOR UNIT 3R & 48) $ (9,268) R 24 Inch G2/L2 Single Star Snow-plus Michelin Radial Tires w/ 3 pc. Rims $ 3, R 24 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 3 pc. Rims $ 2, R 25 Inch L2 Single Star XTLA Michelin Radial Tires w/ 3 pc. Rims $ 3, R 25 Inch L2 Single Star VUT Bridgestone Radial Tires w/ 3pc. Rims $ 2, R 25 Inch L2 Single Star TGD2 Titan Radial Tires w/ 3 pc. Rims Included R25 L3 Goodyear Radial Tires on 3 pc. Rims $ 9, R 25 Inch G3/L3 Single Star XHA Michelin Radial Tires w/ 3 pc. Rims $ 4, R 25 Inch G2/L2 Single Star Sno-plus Michelin Radial Tires w/ 3 pc. Rims $ 5, R 25 Inch G2/L2 Single Star VSW Bridgestone Radial Tires w/ 3 pc. Rims $ 4, R25 Goodyear Snow Tires on 3 pc. Rims $ 7, /65R25 XLD70 G3/L3 Single Star Michelin Low Profile Radial Tires w/3 pc Rims (Requires code 5.28 No Front Fenders. Can not be used with code 5.29 Rear Fenders.) $ 10, Front Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 3 pc. Rim $ 4, Reare Spare Tire: Bridgestone VSW 17.5R25 DG2 1 Star mounted on 3 pc. Rim $ 4, Front Fenders $ No Front Fenders Rear Wheel Fenders in.(476mm) Rear Wheel Fenders Fenders are not for use with 550 tires. Fenders can only be used with chains that are designed for 3" of radial clearance and 1.75" of sidewall clearance. Use of Tire chains permitted in accordance with SAE J683, and requires removal of front mud flap on rear fenders. $ 1, HYDRAULICS Offer hydraulic options. Number starting with 6.1, 6.2, etc. Right Hand - Standard Hydraulic Controls Base Hydraulics - 4 Function Controls Requires code 1.1. Base Functions: Rear Steer, Circle Side shift, Wheel Lean & RH Blade Lift w/ Float Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base functions plus 1 function w/float control - front plumbing and hoses for Scarifier or auxiliary applicaton. For Use with Front Scarifier. $ Mid Mount Scarifier Base Hydraulics w/ 1 Auxiliary Function Control Requires Mid Mount Scarifier code and 1.1. Midmount scarifier base hydraulics with 1 auxilliary function control with float control for mid mount scarifier. For use with mid mount scarifier. $ Base Hydraulics w/2 Auxiliary Function Controls Requires code 1.1. Base functions plus 2 functions w/float control - front plumbing and hoses for Scarifier and/or auxiliary application.for Use with Front Scarifier. $ 1, Base Hydraulics w/ 3 Auxiliary Function Controls Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o float control, front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ 2,098 Right Hand - GRADE PRO CONTROLS Finger-tip armrest mounted controls, consistent with the industry standard pattern. Includes armrest Grade Pro Controls for Mid Mount Scarifier w/1 Auxiliary Function Control Requires codes 1.2 and Mid Mount Scarifier code $ Grade Pro Controls with Base Functions NOTE: * Requires code 1.2. * Grade Pro Base Hydraulics Functions: Rear Steer, Circle Side shift, Wheel Lean, Right and Left hand Blade Lift w/ Float, Circle Rotate, Blade Side Shift, Blade Tilt, Lever Steering (also includes steering wheel) In Configuration Grade Pro Controls w/1 Rear Auxiliary Function and Left Hand Lever Controller Requires code 1.2. Base functions plus 1 auxiliary function w/float control - Rear plumbing 6.09 and 6560 hoses Grade for Pro Ripper Controls or auxiliary w/1 Front applicaton. Auxiliary For Function Use with Control Rear and Ripper. Right Hand Lever $ 757 Controller Requires code 1.2. Base functions plus 1 FRONT auxiliary function w/float control - front plumbing and hoses for Scarifier and/or auxiliary application. For Use with Front Scarifier. $ Grade Pro Controls w/1 Rear Auxiliary Function Control and Right Hand Lever Controller Requires code 1.2. Base functions plus 1 REAR auxiliary function w/float control - front plumbing and hoses for auxiliary application. $ Grade Pro Controls w/1 Front Auxiliary Function and 2 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 3 auxiliary functions- 1 front and 2 rear auxiliary functions w/ float control and rear plumbing for Scarifier / Ripper and/or front, mid $ 2, Grade Pro Controls w/1 Front, 1 Rear Auxiliary Function Control with Right and Left hand Controllers Requires code 1.2. Base Functions plus 2 auxiliary functions - 1 front and 1 rear with float control and plumbing Scarifier / Ripper applications. Auxiliary functions have reconfigurable controls. $ 1, Grade Pro Controls w/1 Front Auxiliary Function and 3 Rear Auxiliary Functions with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 4 auxiliary functions - 1 front and 3 rear with float control and plumbing for Scarifier/Ripper and/or front, mid and rear auxiliary applications. Auxiliary functions have reconfigurable controls. $ 3, Grade Pro Controls w/3 Front and 3 Rear Auxiliary Function Controls with Right and Left hand Controllers and 2 Miniature Multi Axis Joysticks Requires code 1.2. Base Functions plus 6 auxiliary functions-3 front and 3 rear with float control on 4 functions, and includes front and rear plumbing for 2 Functions each. Auxiliary functions have reconfigurable controls. $ 4,540 Left Hand - Standard hydraulic Controls Base Hydraulics- 4 Function Controls Requires code 1.1. Base Functions: LH Blade Lift w/ Float, Blade Side shift, Circle Rotate, Blade Tilt Base Hydraulics w/ 1 Auxiliary Function Control Requires code 1.1. Base Functions plus 1 function w/float control and lines for Ripper or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ Base Hydraulics w/2 Auxiliary Function Control Requires code 1.1. Base functions plus 2 functions w/float control and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 1, Base Hydraulics w/ 3 Auxiliary Function Control Requires code 1.1. Base Functions plus 3 functions-(2) with and (1) w/o Float Control, and lines for Ripper and/or auxiliary application. For Use with Rear Ripper/Scarifier Combination. $ 2, Grade Pro Controls - Left Side NOTE: * Requires code 1.2. * Accompanies GRADE PRO CONTROLS - RIGHT SIDE order code selection. In Configuration Oil, SAE 10W AW46 All Season Hydraulic Oil $ Hydraulic Oil, ISO 46 $ MOLDBOARD/CUTTING EDGE/END BITS/CIRCLE DRIVE

55 Offer these options starting with 7.1, 7.2, 7.3, etc Blade Impact Absorption System Protects Moldboard and draft frame from impacts with Stationary objects $ 1, No Blade Impact Absorption system Ft. x 27 In. x 1 In. (3.66 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ (297) Ft. x 27 In. x 1 In. (3.96 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 5/8 in. (16mm) Hardware $ Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edgeand 5/8 in. (16mm) Hardware NOTE: Requires engine code Ft. x 27 In. x 1 In. (4.27 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 3/4 in. (19mm) Hardware Requires engine code $ Ft. x 27 In. x 1 In. (4.88 M x 686 mm x 25 mm) with 8 In. x 3/4 In. (203 x 19 mm) Cutting Edge and 3/4 in. (19mm) Hardware Requires code 7.19 Slip Clutch, 7.12 Wear Inserts and 7.16 Extensions. $ Extended Life Bronze Wear Inserts NOTE: Recommended for applications in abrasive material. $ Wear Inserts w/o Clutch (Recommended for higher circle torque) Nylon Wear Inserts w/clutch Requires code 7.19 Circle Drive Slip Clutch. Recommended for higher circle torque when used with a slip clutch. $ Reversible Overlay End Bits Not avaible for unit 3R & 48. $ No Reversible Overlay End Bits No Moldboard Extension " 24 in. Left Hand Moldboard Extension Requires Moldboard code 7.05, or $ 1, " 24 in. Right Hand Moldboard Extension NOTE: * * Requires Moldboard code 7.05, or $ 1, Circle Drive with Slip Clutch Protects circle, circle drive gearbox and draft frame from damage when end of moldboard comes in contact with stationary objects. Slip clutch is integral to the circle drive assembly and utilizes a wet clutch system. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 5/8 in. (17mm) Hardware. Cutting Edge is not included. $ 1, AT Moldboard Extension, 27X 24 X 1 In. Left Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 2, AT Moldboard Extension, 27 X 24 X 1 In. Right Hand 1 in. ( 25mm) Thick Includes 3/4 in. (19mm) Hardware. Cutting Edge is not included. $ 1, FRONT ATTACHMENTS Offer front attachment options. Starting with 8.1, 8.2, etc. *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & Front Push Block $ 1, Front Scarifier Includes Front Hydraulics, plumbing and hoses Scarifier with 2 pitch positions and 9 shank pockets Five 1 x 3 inch Scarifier Shanks w/teeth If additional shanks are desired order (1) each of T6Y5230 Tooth, T Shank and T Retainer for each set. Can not be used with 6.07 Hydraulics. $ 4, Mid-Mount Scarifier with Integrated Front Push Plate NOTE: * Requires code 6.03 or 6.06 Hydraulics. * Mid-Mount Scarifier with Push Block Can not be used with Front Scarifier. * Not for use with Front Fenders Code * Recommend Rear Counterweight for better machine balance. $ 6, Balderson Style Front Lift Group NOTE: * Requires Hydraulic code 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13, or * (2) AT Mating Hooks from Parts are available to convert old front attachments to the Bladerson-style lift group. $ 3, Less Front Attachment Front-Mounted Dozer Blade, 105 in. x 37.6 in. (2667 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires one of the following 17.5 x 25 tire codes: 5.01, 5.09, 5.11, 5.12, 5.13, 5.15, 5.16, 5.17, 5.19, 5.20, 5.21, 5.22 $ 4, Front-Mounted Dozer Blade, 115 in. x 37.6 in. (2921 mm x 955 mm) Requires one of the following control valve codes: 6.02, 6.04, 6.05, 6.09, 6.11, 6.12, 6.13 or 6.14 Requires 550/65R25 tire code: $ 4,704 FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Front Hitch Systems - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Standard Hitch System (Pin-on style hitch. 3.5 double acting lift cylinder with 2 rod.) $ 2, Falls Modified 29" Husting Hitch System (Drive -in quick coupler with vertical lift. 3.5 double acting lift cylinder with 2 rod.) $ 3, Falls Modified 34" Husting Hitch System $ 4, Para-Lift Model PLS-1 Hitch System (Drive-in parallel lift quick coupler. $ 3,987 Front Hitch System Options Hydraulic Locking Pin Assembly for Para-Lift Hitch $ Factory Installation of Hydraulic Locking Pin Assy for Para-Lift Hitch $ One Pair Attachment Hooks, Flat Back for Para-Lift Hitch (*Not installed) $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 One Way Snow-Plows Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge, 9'10" Clearing Width w/ Standard Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 29" Husting Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Modified 34" Husting Hitch Coupler $ 6, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Para-Lift Hitch Coupler $ 7, Falls 411H, 12' Cutting Edge, 36" Nose, 66" Discharge w/ Falls Scar-a-Lift or Deere Front Mounted Scarifier Coupler $ 8,110 One Way Snow Plow Options Carbide cutting edge, three (3) pc., 3/4 x 6, per foot $112/ft Rubber belt deflector, 3/8 x 12 $ Heavy duty Spring Trip Tilt Bars, add $ Heavy duty Trip Edge Assembly, add $ 1, Hydraulic Moldboard Tilt, replaces rigid or spring trip bars, add $ Steel caster wheel assemblies, add $ 1, Pneumatic caster wheel assemblies, add $ 1, Left hand discharge, add $ Snow Wheel System, add $ 2,023

56 V-Type Snow Plows - Select the Hitch Attachment Coupler from the Options Falls V-890, 10 gauge A steel moldboard, 10 8 overall width, 9 8 clearing width, 48 nose height, 72 discharge height, three (3) screw-adjustable skid shoes (no tools required), spring loaded snow deflectors $ 6, Falls V-90, 7 gauge A steel moldboard, 12 0 overall width, 9 8 clearing width, 60 nose height, 84 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 6, Falls V-100, 7 gauge A steel moldboard, 13 3 overall width, 10 4 clearing width, 66 nose height, 92 discharge height, three (3) screw-adjustable skid shoes (no tools required). $ 8,342 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System $ 1, Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 2, Plow Unit to fit Falls Para-Lift Hitch System w/oscillating feature $ 1, Plow Unit to fit Falls Para-Lift Hitch System (hooks welded solid) $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,360 V-Type Snow Plow Options Spring Loaded Steel Snow Deflectors (Standard on the Falls V-890) $ Rubber Belt Snow Deflector (3/8" x 12") $ Down Pressure Kit for Standard and Modified Husting Hitch Systems $ Snow-Wheel System (In lieu of standard shoes) $ 4,228 Heavy Duty Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options Falls HDR-11, 11' Cutting Edge, 48" High (*Select Hitch from Options) $ 8, Falls HDR-12, 12' Cutting Edge, 48" High (*Select Hitch from Options) $ 8,958 Hitch Attachment Couplers Plow Unit to fit Falls Para-Lift Hitch System $ Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2, Optional Oscillation Plate (allows plow to follow road contour) $ 1,545 Heavy Duty Reversible Snow Plow Options Carbide Cutting Edge, Add per foot $112//ft Rubber Belt Snow Deflector (3/8" x 12") $ Moldboard Shoes (*Standard Equipment - Not available w/ trip edge assembly) No Charge Screw Adjustable Mushroom Shoes - Set of Two (Can be used with trip edge assembly) $ Trip Edge Assembly (One-piece construction) $ 1,709 Power Reversible Snow Plows - Select the Hitch Attachment Coupler from the Options PR1143 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 6, PR1243 Reversible angle plow. 10 gauge A steel moldboard. 43 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty spring moldboard trip assemblies. Includes industrial strength A-frame. $ 7, PR1155/PR1255 Raise moldboard height on PR1143 or PR1243, add to respective snow plow $ TER-11 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 0 clearing width, 5/8 6 x 11 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6, TER-12 Reversible angle plow. 10 gauge A steel moldboard. 42 moldboard height, 9 10 clearing width, 5/8 6 x 12 ft cutting edge (AASHTO), screw-adjustable mushroom shoes, built-in snow deflector, heavy duty trip edge assembly $ 6,884 Plow-Hitch System Attachment Provides Full Oscillation Left and Right Plow Unit to fit Falls Standard Hitch System $ Plow Unit to fit Falls Modified 29" Husting Hitch System $ 1, Plow Unit to fit Falls Modified 34" Husting Hitch System $ 1, Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 2,032 Power Reversible Snow Plow Options Trip Edge Assembly $ 1, Carbide Cutting Edge Per Foot $112/ft Rubber Belt Snow Deflector, 3/8" x 12" $ Steel Caster Wheel Assemblies $ 1, Pneumatic Caster Wheel Assemblies $ 1, Curb Shoe, Cylindrical, Each $ Curb Shoe, Wrap-Around, Each $ Snow-Wheel System (In lieu of standard shoes) $ 2,729 Dozer Blades - Select the Hitch Attachment Coupler from the Options Falls D3696, 8 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36108, 9 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4, Falls D36120, 10 ft. length, 1/4 steel moldboard, 36 moldboard height, heavy duty push frame, replaceable 5/8 x 6 cutting edge, fixed angle $ 4,620 Hitch Attachment Couplers Plow Unit to fit Falls Standard Hitch System No Charge Plow Unit to fit Falls Modified 29" Husting Hitch System No Charge Plow Unit to fit Falls Para-Lift Hitch System $ 1, Plow Unit to fit Falls Scar-a-Lift or Deere Front Mounted Scarifier $ 1,923 Dozer Blade Options Carbide Cutting Edge, Per Foot $112/ft Scar-A-Lift - (Lift Cylinder included) (*No hydraulic valves or lines included) Falls Model FMS-1 Front Mounted Scarifier $ 5,199 Scar-A-Lift Options Scarifier, Head Only, 5 Teeth, No Head Plate or Arms $ 2, Scarifier, Head Only, 5 Teeth, Para-Lift Hooks Installed $ 3, Scarifier Shank, End Bit and Retainer (Each) $ Para-Lift Attachment Hooks, Flat Back, Per Pair $ Hydraulic Line Quick Coupler Set (1 male, 1 female) $ Hydraulic Line Group from Control Valve to Head Plate, If Required $ 364 HENKE SNOW ATTACHMENTS Henke Fixed Position Dozer Blades DB8 8' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB9 9' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5, DB10 10' Fixed Position Dozer Blade (*Requires Lift Group, Attachment Adapter & Double Acting Valve for the Lift Group) $ 5,348 Lift Group (JRB Installation of Lift Group, Including Freight from Leavenworth

57 8.113 STB-STD Scarifier Tool Bar - Lift Group (*Requires hoses to the nose of the motor grader) $ 4, PLG-STD Parallel Lift Group (*Requires hoses to the nose of the motor grader) $ 3, AQC Automatic Quick Coupler Lift Group (*Requires hoses to the nose of the motor grader) $ 5, HSH Henke Universal Hitch for Grader $ 2,596 Attachment Adapter PSS Plow Scarifier Sockets - Mounts to Henke or Factory Scarifier (Specify) $ PLH Parallel Lift Hooks - Mounts to Henke or field "Balderson Style" Lift Group $ AQC Female Attaching Adapter $ 1,367 Henke REL - Heavy Duty Reversible Snow Plow REL 10 10' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 12 12' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 11, REL 14 14' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 12, REL 16 16' Length, 41" Tall, Tripping, Reversing Blade (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Double Acting Valve for the Plow) $ 13,957 Henke SDDB - Severe Duty Dozer Blade SDDB 10 10' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 12 12' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 11, SDDB 14 14' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12, SDDB 16 16' Width, 48" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 12,356 Henke HH - Henke Helper Utility Blade HH 8 8' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 9 9' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 7, HH 10 10' Length, 41" Tall, Non-Tripping, Reversing Dozer Blade (*Requires Lift Group, Blade) $ 8,067 Henke FV - Multi-Directional Folding Vee Snowplow (MDFVS) FV 12 12' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 14, FV 14 14' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS) $ 15, FV 16 16' Length, 47" Tall, Folding Vee Plow, Includes Swivel (*Requires Lift Group, Attachment Adapter, Double Acting Valve for the Lift Group & Two Double Acting Valves for the MDFVS ) $ 16,622 Henke Tube Table Power Reversible Snow Plows (Include Grader Adaptor) R11TT 50" Tall, Power Reversible Trip Plow w/tube Table Reversing Frame $ 7, R12TT 50" Tall, Power Reversible Trip Plow w/tube Reversing Frame $ 8,095 Henke Plow Options Mushroom Shoes - Pair $ Install Dealer Supplied Coupler $ Parallel Lift Hook Coupler-Supply/Install $ JRB Style Coupler (Verify size and type) $ Hydraulic Hi-Gate for REL (Includes diverter Kit) $ 6, Trip Lockout Option $ ACS Coupler-Supply/Install $ 1,595 Henke V-Plow V-9.5 Vee Plow 9.5 Foot Cutting Swath $ 6, V-10 Vee Plow 10 Foot Cutting Swath $ 7, REAR ATTACHMENTS Offer rear attachment options. Starting with 9.1, 9.2, etc No Rear Attachment Rear Mounted Ripper/Scarifier Combination with Rear Hitch and Pin Includes Rear mounted Ripper/Scarifier with rear hitch and pin. NeverGrease Pin Joints. Three 2 x 5 in. Ripper Shanks w/teeth. Can not be used with codes 6.07, 6.09 or $ 8, Rear Counterweight with Rear Hitch and Pin 1600 lbs.(725.7 kg.) Rear Counterweight. Recommend for use with Front / Mid Scarifier. $ 1, Rear Hitch and Pin Not for use with Rear Ripper/Scarifier. $ (9) Extra Scarifier Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ (2) Extra Ripper Shanks w/teeth For Rear Ripper/Scarifier Requires Code 9.02 Ripper/Scarifier. $ Slow Moving Vehicle (SMV) Sign Included Handi Hitch *Prices Do Not Include Mounting PP01G Handi Hitch Profile Packer/Roller 90" includes Lift Plate, 24" Packer Offset No Installation Included $ 18, HH01G 870GP Lift Assembly/Offset $ 3, PP04G Profile Accumulator and Hoses $ CR10 Handi Hitch Contour Packer/Roller 75" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR12 Handi Hitch Contour Packer/Roller 90" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 17, CR14 Handi Hitch Contour Packer/Roller 105" Mounts directly to rear ripper/scarifier. Includes Accumulator $ 19, CR30 Contour/PP Ripper Shanks $ 1, WR30E Contour Ripper Shank Extender Plates $ 759

58 CR40 Handi Hitch Contour 24" Packer Offset $ 2, CR50 Handi Hitch Contour Heavy Duty Lift Assembly $ 4, CR55 Handi Hitch Contour Accumulator and Hoses $ CR59 John Deere Link Arms (Lift Assembly) $ SIDE ATTACHMENTS Offer side attachment options. Starting with 10.1, 10.2, etc. FALLS SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included (ALL PRICES INCLUDE INSTALLATION AT FALLS) Wings Falls W12 Wing Only, 12 ft. cutting edge moldboard, 36 height, hydraulic-over-cable controls, rear wing post height is manually adjustable. $ 11, Falls W-14 Wing Only, 14 ft. moldboard cutting edge. $ 12, Falls 2012A Wing Only, 12 ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys, rear wing post height is manually adjustable. $ 12, Falls 2012A Low Post (66" vs 100") $ 12, Falls 2014A Wing Only, 14 ft. moldboard cutting edge. $ 13,090 Invisible Mast Snow Wings (Mast Post Fits Under Cab for Maximum Visibility) IM ft. cutting edge moldboard, 36 height, direct hydraulic controls, no cables or pulleys.invisible Mast post fits under cab allowing maximum visibility. $ 17, IM3014 Same as above w/14' Moldboard $ 17,510 Options for Falls Wings Hydraulic Extendable Buffer Brace $ 2, Hydraulic Elevating Rear Slide $ Trip Edge Assembly for 12 Foot Add $ 1, Trip Edge Assembly for 14 Foot Add $ 1, Left Hand Discharge Add $ Ripper Mount in Lieu of Rear Wing Post and Slide No charge HENKE SNOW ATTACHMENTS - No Hydraulic Valves or Controls are Included Price Includes Installation at Factory Wings AHW12FR 12' Grader Wing for Fixed Rear Applications (*Requires 2 valves) $ 11, AHW12MR 12' Grader Wing for Manual Adjusting Rear Applications (*Requires 2 valves) $ 11, AHW12RR 12' Grader Wing for Rear Ripper Applications (*Requires 2 valves) $ 10, AHW12ER 12' Grader Wing for Elevating (Benching) Applications (*Requires 3 valves) $ 12,328 Wing Options ' Grader Moldboard $ Trip Edge Option $ Hi-Gate - Hydraulic End Gate (Includes a diverter kit) $ 4, Factory Installation Wing installation by JRB at the John Deere Factory Included STB-STD Scarifier Tool Bar $ 3, PLG-STD Parallel Lift Group $ 3, AQC Automatic Lift Group $ 4, HSH Henke Standard Hitch (Truck style hitch modified for grader) $ 2, JRB Installation of Lift Group in Davenport Including Freight $ 547 Monroe SNOW ATTACHMENTS (ALL PRICES INCLUDE INSTALLATION AT MONROE) Wings AHW12E-62 for JD "G" Series, 12' All Hydraulic Wing Package w/ 62" Bench Height, 5/8" x 8" Cutting Edge $ 15, AHW12E-38 for JD "G" Series, 12' All Hydraulic Wing Package w/ 38" Bench Height, 5/8" x 8" Cutting Edge $ 15,305 Wing Options Deduct to delete rear post assembly and use ripper-mount bracketry in it's place $ (1,553) Deduct to delete rear post and use 2-position fixed post in it's place $ (1,015) ' Wing Moldboard in Lieu of Standard 12' Model (Requires and/or 10.28) $ Front Lift Group Installed on G-Series Grader $ 5, OTHER ATTACHMENTS Offer other attachment options. Number starting with 11.1, 11.2, etc NS Slopemeter #2 (Installed) $ AT IGC Mast Mounts $ 650 *Attachment Prices Valid with Purchase of Base Machine. Attachments Ordered Individually Subject to Freight, Installation & 12.0 EXTENDED WARRANTY OPTIONS Offer performance/warranty options. Number these starting with 12.1, 12.2, etc. (Specify years, miles or hours extended term covers.) Comprehensive (SEE PRICE MATRIX BELOW) Power Train and Hydraulics (SEE PRICE MATRIX BELOW)

59 12.03 Power Train (SEE PRICE MATRIX BELOW) Engine Only (SEE PRICE MATRIX BELOW) Warranty covers John Deere manufactured components only. Standard Manufacturers Warranty applies to all components that are not manufactured by John Deere Extended Powertrain and Hydraulic Warranty has no Deductible per Occurrence after Initial Warranty - See Attached Extended Warranty Sheet Preventative Maintenance Contract (3 Year/2000 Hour) Cost per Hour $ NEW EQUIPMENT RENTAL PROGRAM If rental programs are available on the new equipment offered, with the option to purchase, list the hourly/weekly/monthly rental rate. Indicate the percent of rental fee paid by the purchaser that will be applied to the purchase price. See Solicitation Special Terms & Conditions. Hourly Rental Rate: NA Weekly Rental Rate: $ 3,150 Monthly Rental Rate: $ 9,450 Percent (%) of Rental Fee applied to purchase price: 100% If the new rental equipment is purchased and finance charges are applicable for the actual rental term only, state the actual interest rate here: NA 14 VENDOR OWNED RENTAL RETURN OR DEMO EQUIPMENT PROGRAM See Solicitation Special Terms and Conditions. DEDUCT cost per Used Hour from the original Contract Price $ DISCOUNT OFF LIST PRICE FOR RELATED PARTS & ACCESSORIES 0% (See Special Terms and Conditions) 16 DELIVERY STARTING POINT City, State, Zip Nearest RDO Equipment RDO Equipment Burnsville, MN Grand Forks, ND Moorehead, MN Rochester, MN Marshal, MN 56258

60 N. Mankato, MN Sauk Rapids, MN Sioux Falls, SD NORTRAX Bemidji, MN Duluth, MN Grand Rapids, MN DELIVERY PRICE PER LOADED MILE No Flat Rate Allowed- See Special Terms and Conditions $6.00 w/$300 Minimum

61 Extended Coverage Customer Personal Service This literature has been compiled for worldwide circulation. While general information, pictures, and descriptions are provided, some illustrations and text may include finance, credit, insurance, product options, and accessories NOT AVAILABLE in all regions. PLEASE CONTACT YOUR LOCAL DEALER FOR DETAILS. John Deere reserves the right to change specification and design of all products described in this literature without notice. DKE6828 Litho in U.S.A. (10-10)

62 At John Deere, feeling secure is not an option Standard warranty promises that, for construction and commercial worksite machines, we ll fix all failures due to defect in material or workmanship for the first 12 months after delivery, free of charge. And on forestry machines, we ll provide standard warranty coverage* to meet the demands of the logging environment. Again, at no charge to you just for doing business with John Deere. But these days, many machine owners feel they need more protection. Extended warranties are an excellent way to protect your cash flow and minimize the risk of doing business. John Deere also offers the exclusive StructurAll warranty that goes above and beyond the standard warranties on non- CWP equipment. The StructurAll warranty provides three years or 10,000 hours (whichever comes first) of no-fear coverage on major machine structures as installed at the factory free of charge, including booms, articulation joints, and mainframes. Extended Coverage is an additional manufacturer-backed warranty program that makes good business sense: It s backed by John Deere Construction & Forestry Company and honored by all Construction and Forestry dealers. Machines covered by an extended warranty can be taken to any North American Construction and Forestry dealer for service. There is no deductible during the Standard Warranty and a $200 deductible on non-powertrain repairs during Full-Machine Extended Coverage. Standard or Extended Coverage warranty can be transferred when you sell or trade your machine.* Financing is available through John Deere finance programs. *Some restrictions apply. *See your local dealer for complete details.

63 Why it pays to extend your coverage Extended warranties provide additional protection that shields you from risk and stress. They are a valuable management tool because they give you fixed costs for machine repairs over a given period of time. Feel secure about Certified Used Equipment You can purchase Certified Used Equipment warranty from participating dealers on qualifying machines. Here are some details: Requires completed machine evaluation. For construction equipment with less than 5,000 hours and newer than five years old. For skidders less than five years old with fewer than 5,000 hours; plus tracked feller bunchers/harvesters, wheeled harvesters, and foresters with less than 10,000 hours and newer than five years old. For Commercial Worksite Products with less than 3,000 hours and newer than three years old. Covers powertrain only.* Three-, six-, or 12-month coverage available with unlimited machine hours.* *Additional coverage may be available; check with your participating dealer. Owner responsibility All you have to do is perform scheduled maintenance as outlined in the Operator s Manual and Extended Warranty contract, and keep accurate maintenance records something you do already. Make fluid analysis part of your maintenance program Fluid analysis helps you reduce downtime, lower repair costs, increase drain intervals, and save money. It keeps you up-to-date on the condition of all your machine s major components and helps you make smart decisions on machine maintenance before and after your Standard and Extended Coverage expires. John Deere requires fluid analysis on most Construction and Forestry machines with new Extended Warranty contracts or extensions.

64 Expanded range of coverage for new equipment Choose one of these four options: 1) Engine Only; 2) Powertrain; 3) Powertrain Plus Hydraulics; 4) Full Machine, or combination of Full Machine and one Powertrain option. Coverage ends when date or hour limit expires. (Items in red indicate coverage added to preceding option.) An extended warranty is like putty in your hands because you can mold it to fit your needs. Want full coverage on the machine, or just the engine? Need 3,000 hours of coverage, or would 5,000 make more sense for the work you do? Items not covered by Extended Coverage Warranty: Ground-engaging tools such as cutting edges and bucket teeth. Hydraulic hoses, lines, and fittings. Maintenance items such as oil and filters. Hydraulic pressure checks and adjustments. Aftermarket attachments such as sweepers, drills, hammers, saws, delimbers, feller bunchers, etc. Wear items. Miscellaneous items.* Damage to machine from abuse or misuse. Collateral damage. Hauling expenses, travel time, mileage, overtime, or second-shift premiums. * Batteries, tires, and radios come with a Direct Supplier Warranty that covers failure due to defective material and workmanship. Engine-Only Coverage ENGINE: Engine and all components within Cylinder head and gasket ECU Electronic engine-speed-control system Engine block Engine oil cooler and aftercooler Flywheel housing and gasket Front and rear engine seals Front damper Hydraulic actuator Injection nozzles Injection pump and gasket Manifolds and gaskets Oil pan and gasket Pressure/temperature sensors and sending units Pressure/temperature sensors and sending units EGR system manifold Ring gear and flywheel Rocker arm cover and gasket Thermostats Timing gear cover Turbocharger and gaskets Water pump and gasket Powertrain Coverage ENGINE: Engine and all components within Cylinder head and gasket ECU Electronic engine-speed-control system Engine block Engine oil cooler and aftercooler Flywheel housing and gasket Front and rear engine seals Front damper Hydraulic actuator Injection nozzles Injection pump and gasket Manifolds and gaskets Oil pan and gasket Pressure/temperature sensors and sending units Pressure/temperature sensors and sending units EGR system manifold Ring gear and flywheel Rocker arm cover and gasket Thermostats Timing gear cover Turbocharger and gaskets Water pump and gasket Engine speed controls and linkages excavators TRANSMISSION/DIFFERENTIAL: Axle(s) and differential(s) Clutch housing (except dry clutch disk) Driveshaft with universal joints Electronic and/or hydraulic control valves Excavator rotary manifold Tracked feller buncher rotary manifold Final drive Front-wheel-drive sensors (not wire harness) Hydraulic-front-wheel-drive axle and wheel assembly (including drive pump and motor, electronic control, solenoid control valve, and divider valve) Hydrostatic system components including: Propel motor, hydrostatic/ hydraulic pump, and related control valves powering propel and/or swing function (not dig function) Mechanical-front-wheel-drive differential/axle assembly with driveshaft, universal joint, and control Pump and valve controller Reverser with control valve Splitter drive Swing gearbox and bearings Swing motor and brake Torque converter Tracked feller buncher rotary manifold Transfer drive Transmission ELECTRICAL: Sensors rotary BRAKES: Wet park brake pinion shaft, bearing, and bearing quill (motor graders only) Wet service brakes

65 Powertrain Plus Hydraulics Coverage Full-Machine Coverage ENGINE: Engine and all components within Cylinder head and gasket ECU Electronic engine-speed-control system Engine block Engine oil cooler and aftercooler Engine speed controls and linkages excavators Flywheel housing and gasket Front and rear engine seals Front damper Hydraulic actuator Injection nozzles Injection pump and gasket Manifolds and gaskets Oil pan and gasket Pressure/temperature sensors and sending units Pressure/temperature sensors and sending units EGR system manifold Ring gear and flywheel Rocker arm cover and gasket Thermostats Timing gear cover Turbocharger and gaskets Water pump and gasket TRANSMISSION/DIFFERENTIAL: Axle(s) and differential(s) Clutch housing (except dry clutch disk) Driveshaft with universal joints Electronic and/or hydraulic control valves Excavator rotary manifold Final drive Front-wheel-drive sensors (not wire harness) Hydraulic-front-wheel-drive axle and wheel assembly (including drive pump and motor, electronic control, solenoid control valve, and divider valve) Hydrostatic system components including: Propel motor, hydrostatic/ hydraulic pump, and related control valves powering propel and/or swing function (not dig function) Mechanical-front-wheel-drive differential/axle assembly with driveshaft, universal joint, and control Pump and valve controller Reverser with control valve Splitter drive Swing gearbox and bearings Swing motor and brake Torque converter Tracked feller buncher rotary manifold Transfer drive Transmission Accumulator and related relief valves (transmission) Hydraulic differential lock valve and associated parts HYDRAULIC COMPONENTS: Control and load-holding valves Cylinder packing kits Hydraulic cylinders Hydraulic oil cooler Hydraulic pumps, motors, and related control valves Hydraulic reservoir Locking pin cylinder Pilot controls ELECTRICAL: Sensors rotary BRAKES: Wet park brake pinion shaft, bearing, and bearing quill (motor graders only) Wet service brakes Wet steering brakes and clutches Brake accumulator (ADT only) STEERING: Crossover relief valve Priority valve Steering pump Steering valves and cylinders ENGINE: Engine and all components within Cylinder head and gasket ECU Electronic engine-speed-control system Engine block Engine oil cooler and aftercooler Engine speed controls and linkages excavators Flywheel housing and gasket Front and rear engine seals Front damper Hydraulic actuator Injection nozzles Injection pump and gasket Manifolds and gaskets Oil pan and gasket Pressure/temperature sensors and sending units Pressure/temperature sensors and sending units EGR system manifold Ring gear and flywheel Rocker arm cover and gasket Thermostats Timing gear cover Turbocharger and gaskets Water pump and gasket Engine mounts and supports Engine oil lines Engine-speed controls and linkages Filter mount Fuel lines Fuel tank and associated parts Fuel transfer pump and gasket Oil filler tube Pulleys Radiator and hoses Water piping TRANSMISSION/DIFFERENTIAL: Accumulator and related relief valves (transmission) Axle(s) and differential(s) Clutch housing (except dry clutch disk) Driveshaft with universal joints Electronic and/or hydraulic control valves Excavator rotary manifold Final drive Front-wheel-drive sensors (not wire harness) Hydraulic-front-wheel-drive axle and wheel assembly (including drive pump and motor, electronic control, solenoid control valve, and divider valve) Hydraulic differential lock valve and asso ciated parts Hydrostatic system components including: Propel motor, hydrostatic/ hydraulic pump, and related control valves powering propel and/or swing function (not dig function) Mechanical-front-wheel-drive differential/axle assembly with driveshaft, universal joint, and control Pump and valve controller Reverser with control valve Splitter drive Swing gearbox and bearings Swing motor and brake Torque converter Tracked feller buncher rotary manifold Transfer drive Transmission Control rods Differential lock valve and associated parts External oil lines Filler tubes (transmission) Filter screens Oil cooler Sending units and sensors Shift-control linkage HYDRAULIC COMPONENTS: Control and load-holding valves Cylinder packing kits Hydraulic cylinders Hydraulic oil cooler Hydraulic pumps, motors, and related control valves Hydraulic reservoir Locking pin cylinder Pilot controls

66 Full-Machine Coverage (continued) BRAKES: Brake accumulator (ADT only) Wet park brake pinion shaft, bearing, and bearing quill (motor graders only) Wet service brakes Wet steering brakes and clutches Brake accumulator (non-adt) Brake pump Brake valve Pressure-reducing valve Unloading valve ELECTRICAL: Sensors rotary Alternator Gauges Indicators Instruments Sensors Starter Starter drive Starter solenoid Switches Voltage regulator Wiper motors Wiring harnesses FACTORY-INSTALLED AIR CONDITIONING: Accumulator Clutch Compressor Condenser Dryer Evaporator Expansion valve Heater hose Pulley Seals and gaskets Temperature-control programmer OTHER: Bucket linkages Circle drive gearbox Fan and fan drive Motor grader circle Scarifier and ripper linkages Undercarriage components wear undercarriage items not covered (except by special contract) Winch factory installed only STEERING: Crossover relief valve Priority valve Steering pump Steering valves and cylinders Axles Secondary steering system components Spindles and supports Steering linkage Tie rods and tie-rod ends STRUCTURES: Arm Articulation joint (including pins and bushings) Bin frame Boom Carbody C-frame Circle frame Dipperstick Draft frame Engine frame Equipment frame Forklift mast and frame Grapple arch and grapple boom Loader arm Loader frame Mainframe Moldboard lift arm Rollover protection structure (ROPS) Side frame Swing frame Track frame X-frame Z-bar PNEUMATIC COMPONENTS (ARTICULATED DUMP TRUCK ONLY): Airline hoses, lines, and fittings Brake system air components Dump body Four-way protection valve Unloading valve There s enough day-to-day stress in the construction and forestry business without worrying about unpredictable machine-repair expenses. That s why you owe it to yourself and your bottom line to find out about Extended Coverage warranty. Extended Coverage warranty is a factory-backed extended warranty that s flexible enough to meet the needs of any business or government agency. Call your John Deere dealer for all the facts today. This brochure does not include all the information you need to know about the Extended Coverage warranties. For complete details, read a copy of the Extended Coverage warranty contract.