Series 900A. product guide. contents. features. 103' (31.4 m) Four-Section Boom. Features Ton (23.6 mt) Rating

Transcription

1 Series 9A product guide features 13' (31.4 m) Four-Section Boom 26 Ton (23.6 mt) Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block contents Features 2 Mounting Configurations 3 Specifications 4 Capacities 5 Accessories 11 Dimensions Specifications 12 *Product may be shown with optional equipment.

2 features Why Buy a National Series 9A? 2 26-ton (23.6 mt) Rating The 9A provides a 26-ton (23.6 mt) capacity. New 13 ft. (31.4 m) Four-section Boom The longest in its size range. The longer boom allows the operator to perform more lifts without the use of a jib, reducing setup time and improving efficiency. Self-lubricating Easy Glide Wear Pads The self-lubricating pads, standard on the 9A reduce the conditions that cause boom chatter and vibration. The net result is smoother crane operation. *Product may be shown with optional equipment. Internal Anti-two-block The patent-pending design, standard on the 9A eliminates the external reel and wire. No more snagging reel or wire on obstructions. Adjustable Swing Speed A control knob located on the swing motor brake release valve can be easily adjusted to the crane operator s swing speed preference. Speedy-reeve Boom Tip and Sheave Blocks These standard features simplify rigging changes. 26-ton (23.6-mt) maximum capacity Pre-painted Components Painting crane components before assembly reduces the possibility of rust, improves serviceability and enhances the appearance of the machine. 156 ft. (47.5 m) maximum vertical reach* 112 ft. (34.1 m) maximum vertical hydraulic reach* Hydraulic Capacity Alert system (HCA) or Load Moment Indicator System (LMI) Proportional boom extension High performance planetary winch Heavy-duty triple pump hydraulics * Maximum vertical reach is groundlevel to boom tip height at maximum extension and angle with outriggers/stabilizers fully extended. 9A Burst-of-Speed Winch Provides faster winch payout and pickup of unloaded cable. Electronic versions of manuals available through Manitowoc Crane CARE. Improved Serviceability A removable winch allows the internal telescoping cylinder to be removed quickly, without dismantling the boom. Bearings on the boom extend and retract cables can be greased through access holes in the boom side plates. Internal anti-two-block wire routing eliminates damage potential. The boom sheave case is open, allowing access to replace the internal anti-two-block wire and to observe internal boom components. Pre-paint reduces rust. Internal boom parts have been reduced, decreasing service time when rebuilding the machine. National Crane Is the Market Leader National is number one in the production of commercial truck-mounted boom trucks, with more than 35, units sold. National has many programs and people directly and indirectly involved to provide our customers with reliable products. National has the boom truck industry s leading test program. Every structural part of the crane is fully life cycle tested at full capacity. In addition to cycle testing, each model is subjected to state-of-the-art strain gauge testing that measures metal deformation as small as one-millionth of an inch. The net result is that weak areas are caught in test, not on job sites where costly downtime occurs. All outrigger, lift and telescoping cylinders are manufactured to National Crane Designs, so that the seals, packing glands, and end plates are traced for accurate shipment of replacement parts. National has a formalized quality program and is ISO 91 approved. Parts are available for all National Crane machines for the life of the crane. National Crane Is a Quality Product That Will Provide Years of Service Parts are available for all National Crane machines, even if they are over 2 years old.

3 mounting configurations The configurations are based on the Series 9A with an 85% stability factor. The complete unit must be installed in accordance with factory requirements and a test performed to determine actual stability and counterweight requirements since individual truck chassis vary. 64" (1625 mm) 64" (1625 mm) 64" (1625 mm) *88 LBS (3991 kg) SFO *88 LBS (3991 kg) *88 LBS (3991 kg) SFO 64" (1625 mm) 74" (1879 mm) 3" (76 mm) 192" (4876 mm) 3" (76 mm) 192" (4876 mm) 3" (76 mm) 168" (4267 mm) *95 LBS (439 kg) *95 LBS (439 kg) Estimated Average Final Weight...4,9 lb (18 1 kg) This configuration allows the installation of the 99A or 969A on a chassis by using a subbase for a 2-ft (6.1-m) bed or a different subbase for a 22-ft (6.71-m) bed. This mount requires front stabilizer for full capacity 36 around the truck. Front stabilizer gives the machine a solid base, helping the operator control loads. Notes: Gross Vehicle Weight Rating (GVWR) is dependent on all components of the vehicle (axles, tires, springs, frame, etc.) meeting manufacturers recommendations; always specify GVWR when purchasing trucks Diesel engines require a variable speed governor and energize-to-run fuel solenoid for smooth crane operation; electronic fuel injection requires EET engine remote throttle All mounting data is based on a National Series 9A with an 85 percent RSOD *Estimated axle scale rates prior to installation of crane, stabilizers and subbase for 85% stability. Configuration 1 913A Working area...18 Gross Axle Weight Rating Front...16, lb (7257 kg) Gross Axle Weight Rating Rear...34, lb ( kg) Gross Vehicle Weight Rating...5, lb ( kg) Wheelbase in ( cm) Cab to Axle/trunnion (CA/CT) in (488 cm) Frame Section Modulus (SM) under crane: 11, PSI (8 MPa)...2 in 3 (327 cm 3 ) Frame Section Modulus (SM) over rear stabilizers: 11, PSI (8 MPa)...15 in 3 (2 cm 3 ) Stability Weight, Front...8,8 lb (3991 kg) minimum* Stability Weight, Rear...9,5 lb (439 kg) minimum* Estimated Average Final Weight...42,6 lb ( kg) This configuration allows the installation of the Series 913A on a chassis by using the subbase for a 22-ft (6.71-m) bed. *95 LBS (439 kg) RSOD Configuration 2 913A with SFO (Extended front frame rails required for SFO installation.) Working area...36 Gross Axle Weight Rating Front...16, lb (7257 kg) Gross Axle Weight Rating Rear...34, lb ( kg) Gross Vehicle Weight Rating...5, lb ( kg) Wheelbase in ( cm) Cab to Axle/trunnion (CA/CT) in (488 cm) Frame Section Modulus (SM) under crane: 11, PSI (8 MPa)...2 in 3 (327 cm 3 ) Frame Section Modulus (SM) over rear stabilizers: 11, PSI (8 MPa)...15 in 3 (2 cm 3 ) Stability Weight, Front...8,8 lb (3991 kg) minimum* Stability Weight, Rear...9,5 lb (439 kg) minimum* Estimated Average Final Weight...42,9 lb (19 9 kg) This mount requires front stabilizer for full capacity 36 around the truck. Front stabilizer gives the machine a solid base, helping the operator control loads. This configuration requires a 22-ft (6.71-m) bed. *95 LBS (439 kg) RSOD Configuration 3 99A / 969A Working area...18 Gross Axle Weight Rating Front...16, lb (7257 kg) Gross Axle Weight Rating Rear...34, lb ( kg) Gross Vehicle Weight Rating...5, lb ( kg) Wheelbase in (9 cm) Cab to Axle/trunnion (CA/CT) in (427 cm) Frame Section Modulus (SM) under crane: 11, PSI (8 MPa)...2 in 3 (327 cm 3 ) Frame Section Modulus (SM) over rear stabilizers: 11, PSI (8 MPa)...15 in 3 (2 cm 3 ) Stability Weight, Front...8,8 lb (3991 kg) minimum* Stability Weight, Rear...9,5 lb (439 kg) minimum* Estimated Average Final Weight...4,6 lb ( kg) This configuration allows the installation of the Series 99A or 969A on a chassis with a small frame by using a subbase for a 2-ft (6.1-m) bed or a different subbase for a 22-ft (6.71-m) bed. *88 LBS (3991 kg) *85 LBS (38 kg) 3" (76 mm) 168" (4267 mm) 17" (4318 mm) *88 LBS (3991 kg) " (195 mm) C L AF 112" (2844 mm) RSOD SRO Configuration 4 99A / 969A with SFO (Extended front frame rails required for SFO installation.) Working area...36 Gross Axle Weight Rating Front...16, lb (7257 kg) Gross Axle Weight Rating Rear...34, lb ( kg) Gross Vehicle Weight Rating...5, lb ( kg) Wheelbase in (9 cm) Cab to Axle/trunnion (CA/CT) in (427 cm) Frame Section Modulus (SM) under crane: 11, PSI (8 MPa)...2 in 3 (327 cm 3 ) Frame Section Modulus (SM) over rear stabilizers: 11, PSI (8 MPa)...15 in 3 (2 cm 3 ) Stability Weight, Front...8,8 lb (3991 kg) minimum* Stability Weight, Rear...9,5 lb (439 kg) minimum* Configuration 5 Rear Mount Working area...36 Gross Axle Weight Rating Front...16, lb (7257 kg) Gross Axle Weight Rating Rear...4, lb ( kg) Gross Vehicle Weight Rating...56, lb (25 41 kg) Wheelbase in (62 cm) Cab to Axle/trunnion (CA/CT)...IMUM 17 in (432 cm) Frame Section Modulus (SM) under crane: 11, PSI (8 MPa) in 3 (26 cm 3 ) Stability Weight, Front...8,5 lb (38 kg) minimum* Stability Weight, Rear...7, lb (3991 kg) minimum* Estimated Average Final Weight...43, lb (19 54 kg) This configuration allows the rear-mount installation of the Series 9A. This configuration is 36 stable and allows the effective use of close working area to lift the heavier capacity loads. Maximum bed length is 16 ft (4.87 m). stability factor The complete unit must be installed in accordance with factory requirements, and a test performed to determine actual stability and counterweight requirements per SAE J7; contact the factory for details Transmission neutral safety interlock switch is required with optional remote control 3 9A

4 specifications Boom and Jib Combinations Data 4 Available in three basic models. Model 969A Equipped with a 27 ft 6 in - 69 ft 2 in ( m) three-section boom. Maximum tip height ft (24 m). This model can be equipped with a ft ( m) two-section jib. Maximum tip height w/44 ft (13.41m) jib is 123 ft 9 in. (37.71m) ( m) three-section boom 9FJ44M ft ( m) two-section jib Model 99A Equipped with a 27 ft 6 in - 9 ft 6 in ( m) four-section boom. This model can be equipped with a ft ( m) two-section jib. Maximum tip height w/ 44 ft (13.41 m) jib is 143 ft (43. m) ( m) four-section boom 9FJ44M ft ( m) two-section jib Model 913A Equipped with a 3 ft 9 in - 12 ft 1 in ( m) four-section boom. This model can be equipped with a ft ( m) two-section jib. Maximum tip height w/ 44 ft (13.41 m) jib is 1 ft (47.24 m) ( m) four-section boom 9FJ44M ft ( m) two-section jib Note: maximum tip height is measured with outriggers/stabilizers fully extended. 9A Winch Data 9A Winch Data All winch pulls and speeds in this chart are shown on the fourth layer Winch line pulls would increase on the first, second and third layers Winch line speed would decrease on the first, second and third layers Winch line pulls may be limited by the winch capacity or the ANSI 5 to 1 cable safety factor Hook blocks are rated at maximum capacity for the block. Do not exceed rated cable pull with any block. 1 Part Line 2 Part Line 3 Part Line 4 Part Line 5 Part Line 6 Part Line 7 Part Line MAX. PULL 7,7 lb MAX. PULL 15,4 lb MAX. PULL 23,1 lb MAX. PULL 3,8 lb MAX. PULL 38,5 lb MAX. PULL 46,2 lb MAX. PULL, lb Cable Avg. Breaking Lift and Lift and Lift and Lift and Lift and Lift and Lift and Winch Supplied Strength Speed Speed Speed Speed Speed Speed Speed Standard 9/16" Diameter 38,5 lb 7,7 lb (3 492 kg) 15,4 lb (6 985 kg) 23,1 lb (1 477 kg) 3,8 lb (13 97 kg) 38,5 lb ( kg) 46,2 lb (2 9 kg), lb (23 6 kg) Planetary Winch Rotation Resistant ( kg) 135 fpm (41 m/m) 68 fpm (2 m/m) fpm (13 m/m) 34 fpm (1 m/m) 27 fpm (8 m/m) 23 fpm (7 m/m) 19 fpm (5 m/m) With Same as corresponding 3, lb (1 36 kg) 6, lb (2 721 kg) 9, lb (4 82 kg) 12, lb (5 443 kg) 15, lb (6 83 kg) 18, lb (8 164 kg) 21, lb (9 5 kg) Burst-of-Speed cable data shown above 26 fpm (62 m/m) 13 fpm (31 m/m) 64 fpm (19.51 m/m) 51 fmp (15 m/m) 41 fpm (12 m/m) 34 fpm (1 m/m) 29 fpm (8 m/m) 9A Winch Bare Drum Pull Allowable Cable Pull With standard rotation resistant rope...1,2 lb (4627 kg)...7,7 lb (3493 kg) Block Type Rating Weight Downhaul Weight ton (3.49 t)...15 lb (68 kg) 1 Sheave Block ton (1.48 t)...35 lb (138 kg) 2 Sheave Block ton (17.46 t)...3 lb (161 kg)

5 capacities Load Chart Rating: Series 969A (21. m) Boom with 44 ft. (13.4 m) Jib 2ND JIB 44FT 1ST JIB 25FT LENGTH IN FEET A B C SERIES 969A WITH 44FT JIB LMI CAPACITIES 13 DO NOT EXTEND JIB INTO THIS AREA HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine RADIUS IN FEET SERIES 969A WITH 44 JIB NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths. 3. Capacities do not exceed 85% stability. 4. Shaded areas are structurally limited capacities. LOADLINE EQUIPMENT DEDUCT Downhaul weight 15lb. (68kg) One sheave block 35lb. (138kg) Two sheave block 3lb. (161kg) Three sheave block 5lb. (26kg) Load Chart Rating: Series 969A (21. m) Boom with 44 ft. (13.4 m) Jib LOAD RADIUS (FEET) ADD TO CAPACITIES WHEN NO JIB STOWED 27FT, 36,5 31, 26,5 21,6 19,3 15, 6, A 39FT 24,7 21,2 16,8 15,2 11,6 9,25 7,1 3, B 49FT 23,9 2,2 16,2 15,2 11,7 9,35 7,6 6,3 5,5 2, THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. C 59FT 22,8 19,1 17, 14,8 11,8 9, 7,7 6,4 5,15 4,2 3,4 1, FT 17,6 15,6 13,5 11,4 9, 7,8 6,5 5,25 4,3 3,7 3,5 2, 1,5 2 LOAD RADIUS (FEET) FT JIB 7,7 6,8 5,9 5,1 4,4 3,85 3,4 3, 2,6 2,25 1,95 1, 1, FT JIB 4,5 4,1 3,8 3,5 3,2 3, 2,8 2,6 2,4 2,15 1,95 1, 1, 1,35 1, A

6 capacities Load Chart Rating: Series 969A (21.m) Boom 6 LENGTH IN FEET SERIES 969A WITH NO JIB LMI CAP A B C HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. RADIUS IN FEET SERIES 969A/ NO JIB NOTE: 1. Capacities do not exceed 85% stability. 2. Shaded areas are structurally limited capacities. LOADLINE EQUIPMENT DEDUCT Downhaul weight 15lb. (68kg) One sheave block 35lb. (138kg) Two sheave block 3lb. (161kg) Three sheave block 5lb. (26kg) Load Chart Rating: Series 969A (21.m) Boom 9A LOAD RADIUS (FEET) FT, 37,2 31,7 27,2 22,3 2, 15,7 7, A 39FT 25,2 21,7 17,3 15,7 12,1 9, 7,6 4,2 24,3 2,6 16,6 15,6 12,1 9, 8, 6,7 5, THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane B 49FT 2, C 59FT 23,1 19,4 17,3 15,1 12,1 9, 8, 6,7 5, 4,5 3,7 1, FT 17,8 15,8 13,7 11,6 9, 8, 6,7 5, 4,5 3,9 3,25 2, 1,25

7 capacities Load Chart Rating: Series 99A (27.4 m) Boom with 44 ft. (13.4 m) Jib 2ND JIB 44FT 1ST JIB 25FT LENGTH IN FEET A B C D RADIUS IN FEET 5 2 SERIES 99A WITH 44FT JIB LMI CAPACITIES DO NOT EXTEND JIB INTO THIS AREA HEIGHT IN FEET STRUCTURAL LENGTH LIMIT CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. 7 SERIES 99A WITH 44 JIB NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths. 3. Capacities do not exceed 85% stability. 4. Shaded areas are structurally limited capacities. LOADLINE EQUIPMENT DEDUCT Downhaul weight 15lb. (68kg) One sheave block 35lb. (138kg) Two sheave block 3lb. (161kg) Three sheave block 5lb. (26kg) Load Chart Rating: Series 99A (27.4 m) Boom with 44 ft. (13.4 m) Jib LOAD RADIUS (FEET) ADD TO CAPACITIES WHEN NO JIB STOWED 27FT, 35,9 3,6 25,9 21,6 19,3 14,8 6, A 42FT 26,9 23, 2,1 17,8 14,6 11,3 9,5 7,5 3, B 54FT 25,3 21,6 2,1 16,7 14,5 11, 8,9 7,35 6,1 4,9 3,85 1, C 66FT 18,1 15,7 13,6 11, 9, 7,2 6, 5,1 4,35 3, 2, 7 2 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane D FT 14,7 12,5 1,3 8,6 7,15 5,85 4,9 4,25 3, 3,1 2, 1,95 1, FT 11,5 9,3 7,8 6,7 5,85 4,9 4,25 3,7 3,25 2,8 2,35 1,95 1, 95 1 LOAD RADIUS (FEET) FT JIB 4,85 4,35 3,9 3,5 3,15 2,8 2,5 2,2 1, 1,4 1, FT JIB 3,3 3,25 3,2 3,5 2, 2,4 2,15 1,9 1,7 1, 1,4 1,25 1, 8 6 LOADLINE EQUIPMENT DEDUCT ( lb ) Downhaul weight 15lb. (68kg) One sheave block 35lb. (138kg) Two sheave block 3lb. (161kg) Three sheave block 5lb. (26kg) 9A

8 capacities Load Chart Rating: Series 99A (27.4 m) Boom 8 LENGTH IN FEET A B C D 4 6 RADIUS IN FEET SERIES 99A WITH NO JIB LMI CAPACITIES 8 STRUCTURAL LENGTH LIMIT HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. SERIES 99A/ NO JIB LOADLINE EQUIPMENT DEDUCT Downhaul weight 15lb. (68kg) One sheave block 35lb. (138kg) Two sheave block 3lb. (161kg) Three sheave block 5lb. (26kg) Load Chart Rating: Series 99A (27.4 m) Boom 9A LOAD RADIUS (FEET) FT, 36,6 31,3 26,6 22,3 2, 15,5 7, A 42FT 27,3 23,4 2,5 18,2 15, 11,7 9, 7, 3, B 54FT 25,6 21,9 2,4 17, 14,8 11,3 9,2 7, 6,4 5,2 4,15 1,9 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane C 66FT 18,3 15,9 13,8 11,2 9,2 7,4 6,2 5,3 4, 3, 2, D FT 14,9 12,7 1,5 8,8 7,35 6,5 5,1 4, 3,85 3,3 2, 2,15 1, FT 11,6 9,4 7,9 6,8 5,95 5, 4,35 3,8 3,35 2,9 2, 2,5 1, 1,5

9 capacities Load Chart Rating: Series 913A (31.4 m) Boom with 44 ft. (13.4 m) Jib 2ND JIB 44FT 1ST JIB 25FT LENGTH IN FEET D C B A RADIUS IN FEET DO NOT EXTEND JIB INTO THIS AREA HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine Load Chart Rating: Series 913A (31.4 m) Boom with 44 ft. (13.4 m) Jib 4 DO NOT 8 LOAD EXTEND 3FT RADIUS JIB INTO (FEET) 3 THIS 5 AREA 6.5, 8 34, , , , ,95 14, RADIUS IN FEET ,5 ADD TO CAPACITIES WHEN NO JIB STOWED SERIES 913A 14 WITH 5 44 JIB 12 1 HEIGHT IN FEET A 43FT 26,4 22,5 19,6 17,3 14, 1,8 8,5 6,5 2,2 6 NOTE: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths. 3. Capacities do not exceed 85% stability. 4. Shaded areas are structurally limited capacities. SWITCH B C D POSITION FT OPERATING 73FT MODE 88FT 1 MAIN - NO JIB STOWED 2 MAIN - JIB STOWED 8 24, ,25 25 FT TELE JIB , FT TELE 17, JIB ,35 MAN BASKET 15,35 ON 8MAIN 14, , 74 12, , MAN BASKET ON 25 FT TELE JIB , 7 1, , ,5 MAN BASKET ON 44 FT TELE JIB.5 6,9.5 5, 38 4,5 28 3, LMI OPERATING CODE SWITCH ,35 6,8 5,6 4,7 3,95 3,15 2, , 6,4 5, 4,6 3,95 3,3 2, 2,2 1, 1, FT 1, 9,1 7,15 6,5 5,15 4,5 3,9 3,35 2,9 2, 2,5 1, 1, LOADLINE EQUIPMENT DEDUCT Downhaul weight 15lb. (68kg) One sheave block 35lb. (138kg) Two sheave block 3lb. (161kg) Three sheave block 5lb. (26kg) LOAD RADIUS (FEET) FT JIB 3,95 3, 3,5 2,6 2,25 1,95 1,8 1, 1,3 1, FT JIB 2, 2,5 2, 2,25 1,85 1, 1,35 1,2 1, LOADLINE EQUIPMENT DEDUCT ( lb ) Downhaul weight 15 lb (68 Kg) One sheave block 35 lb (138 Kg) Two sheave block 3 lb (161 Kg) Three sheave block 5 lb (26 Kg) THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 9A

10 capacities Load Chart Rating: Series 913A (31.4 m) Boom 1 LENGTH IN FEET LENGTH IN FEET B D B 4 3 D RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 1 ft (3m) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii 12 Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. 1 Always level the crane with the level indicator located on the crane. 1. Capacities do not exceed 85% stability. The operator 2. must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on 8 freely suspended loads. Overloading this crane may cause structural collapse or instability. SWITCH Weights on any OPERATING POSITION accessories attached to the boom MODE or loadline 6 must be deducted from the load chart capacities. 1 MAIN - NO JIB STOWED Do not exceed jib capabilities at any reduced boom lengths. 11 MAN BASKET ON MAIN Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Downhaul weight Tw ve block HEIGHT IN FEET SERIES 913A/ NO JIB RADIUS IN FEET 8 1 LOADLINE EQUIPMENT DEDUCT Downhaul weight 15lb. (68kg) One sheave block 35lb. (138kg) Two sheave block 3lb. (161kg) Three sheave block 5lb. (26kg) Load Chart Rating: Series 913A (31.4 m) Boom 9A LOAD RADIUS (FEET) FT, 35,7 29,9 25,6 22,1 19,8 15,2 5, A 43FT 27, 23,1 2,2 17,9 14,6 11,4 9,1 7,1 2, B FT 25,4 21,7 19,8 16,8 14,2 11, 8,95 7,35 6,1 4,95 3,9 1,25 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane C 73FT 18,1 15,7 13, 1,5 8,7 7,15 5,95 5,5 4,3 3,5 2, D 88FT 14,6 12, 9,7 8,5 6,7 5, 4,9 4,25 3,6 3,5 2,5 2,5 1, FT 1,8 9,35 7,4 6,3 5,4 4, 4,15 3,6 3,15 2,7 2,3 1,9 1,5 1,15

11 Radio Remote Controls Eliminate the handling and maintenance concerns that accompany cabled remotes. Operate to a range of about 25 feet (76 m), varying with conditions. One-Person Basket Strong but lightweight steel basket with 3-lb. (139-kg) capacity, gravity hung with swing lock and full body harness. Heavy-duty Personnel Basket 1,2-lb. (544-kg) capacity steel basket with safety loops for four passengers. Gravity leveling 72- x 42-inch (183- x 17-cm) platform. Fast attachment and secure locking systems. Load chart must show 2,3 (143 kg) minimum to operate this accessory. Hydraulic Oil Cooler Automatic, self-contained radiator system with electric fans, cools oil under continuous duty-cycle operations. Continuous Rotation Allows rotation of turret/boom without stop. Single Front Outrigger Center mount front stabilizer with 25 vertical stroke. Outrigger Motion Alarms Available for A frame O/R only, not stabilizers. Available for A frame outriggers (Std mount only) and RSOD stabilizers. Hour Meter Hour meter in truck cab to record crane operation hours. Steel Tool Box Options Spanish-Language Danger Decals, Control Knobs, and Operators Manuals accessories NB4R (R4 functions) B1-S 2B1-S (for dual locking baskets) BSA-1 BSA-R1 (provides rotation) OC CR SFO OMA-1 OMA-2 HRM SDD SOM 11 9A

12 dimensions specifications Dimensions Specifications 12 ALL DIMENSIONS IN INCHES (MM) UNLESS OTHERWISE SPECIFIED 9A

13 notes 13 9A

14 notes 14 9A

15 notes 15 9A

16 Regional Headquarters Americas Manitowoc, Wisconsin, USA Tel: Fax: Shady Grove, Pennsylvania, USA Tel: Fax: Europe, Middle East, Africa Ecully, France Tel: Fax: Asia Pacific Shanghai, China Tel: Fax: Singapore Tel: Fax: Regional Offices Americas Brazil Alphaville Tel: Fax: Mexico Monterrey Tel: Fax: Europe, Middle East, Africa Algeria Hydra Tel: Fax: Czeck Republic Netvorice Tel: Fax: France Baudemont Tel: Fax: Cergy Tel: Fax: Decines Tel: Fax: Germany Langenfeld Tel: Fax: Hungary Budapest Tel: Fax: Italy Parabiago Tel: Fax: Netherlands Breda Tel: Fax: Poland Warsaw Tel: Fax: Portugal Alfena Tel: Fax: Lisbon Tel: Fax: Russia Moscow Tel: Fax: U.A.E. Dubai Tel: Fax: U. K. Middlesex Tel: Fax: Sunderland Tel: Fax: Asia Pacific Australia Melbourne Tel: Fax: Sydney Tel: Fax: China Beijing Tel: Fax: Xi an Tel: Fax: Korea Seoul Tel: Fax: Philippines Makati City Tel: Fax: Factories U.S.A. Manitowoc Shady Grove Brazil Alphaville France Charlieu La Clayette Moulins India Calcutta Puna Italy Niella Tanaro Germany Wilhelmshaven Portugal Fânzeres China Zhangjiagang Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment and price changes without notice. Illustrations shown may include optional equipment and accessories, and may not include all standard equipment. 27 MANITOWOC Printed in USA Form No. 9A / 77 / 2M