National Crane 600E2 Series
|
|
- Lester Perry
- 5 years ago
- Views:
Transcription
1 National Crane 6E2 Series Product Guide Features 27,4 m (9 ft) foursection boom 18,1 t (2 USt) rating Self-lubricating Easy Glide wear pads Internal anti-two block
2 Features National Crane Series 6E2,3 t (18 USt) maximum capacity 36,9 m (121 ft) maximum vertical reach 24,7 m (81 ft) maximum vertical hydraulic reach Four-section boom At 9 ft, the Series 6E2 four-section boom is the longest in its size range. The long boom allows the operator to perform more lifts without the use of a jib, reducing setup time and improving efficiency. Easy Glide boom wear pads Easy Glide boom wear pads reduce the conditions that cause boom chatter and vibration. The net result is smoother crane operation. Outriggers The Series 6E2 comes equipped with A-frame outriggers and ASH rear stabilzers. An optional single front stabilizer is available for 36 stability. Rear stabilizers include an independent stabilizer control and bolt/clamp-on mounting. Outriggers are equipped with a motion alarm and an outrigger monitoring system. Front: 6,73 m (22.8 ft) span Rear: 3 m (1 ft) span
3 Features Best in class performance and serviceability The steel torsion box and flatbed further reduce frame flex Speedy-reeve boom tip and sheave blocks simplify rigging changes by decreasing the time needed to change line reeving Crane components painted before assembly reduce the chance of rust, improve serviceability and enhance the appearance of the crane A control knob located on the swing motor brake release valve can be easily adjusted to the crane operator s swing speed preference Engine start/stop switches Emergency stop overrides located at control station Hydraulic reservoir capacity of 66 gal Serviceability * Product may be shown with optional equipment. Bearings on the boom and retract cables can be greased through access holes in the boom side plates. Removable winch allows the internal telescoping cylinder to be removed quickly, without dismantling the boom Internal anti-two-block wire routing eliminates external reel and wire to protect crane components The boom sheave case is open, allowing access to replace the internal anti-two-block wire and to observe internal boom components Internal boom parts have been reduced, decreasing service time when rebuilding the machine
4 Contents Features 2 Mounting configurations 5 Specifications 6 Capacities 8 Dimensions Accessories 17 4
5 CWT Mounting configurations The configurations are based on the Series 6E2 with an 85% stability factor. The complete unit must be installed in accordance with factory requirements and a test performed to determine actual stability and counterweight requirements since individual truck chassis vary mm (") MIN 3629 kg (8 lb) MIN 4264 kg (94 lb) MAX 46 mm (4") MIN CWT 4763 kg (1,5 lb) ASH Configuration 1 with Torsion Box 18 Full Capacity Work Area Working area Gross Axle Weight Rating Front... 6 kg (14, lb) Gross Axle Weight Rating Rear kg (34, lb) Gross Vehicle Weight Rating kg (48, lb) Wheelbase cm (232 in) Cab to Axle/trunnion (CA/CT) cm (4 in) Frame Section Modulus (SM) under crane: (758 MPa 11, PSI)... 2 cm 3 (15.9 in 3 ) Frame Section Modulus (SM) over rear stabilizers: (758 MPa 11, PSI) cm 3 (13 in 3 ) Stability Weight, Front kg (8 lb) minimum* Stability Weight, Rear kg (1,5 lb) minimum* Estimated Average Final Weight kg (3, lb) Requires front SFO stabilizer to give machine full capacity 36 around the truck. Truck must meet the minimum requirements above. Front stabilizer gives the machine a solid base, helping the operator control loads precisely. Extended front frame rails required for SFO installation. SFO 18 cm³ (11 in³) 33 cm³ 1727 mm (2in³) (") 123 cm³ MIN (7.5 in³) 3493 kg (77 lb) MIN 482 (9 lb) MAX 328 cm³ (2 in³) 46 mm (4") MIN 4763 kg (1,5 lb) ASH Configuration 2 with Torsion Box 36 Full Capacity Work Area Working area...36 Gross Axle Weight Rating Front... 6 kg (14, lb) Gross Axle Weight Rating Rear kg (34, lb) Gross Vehicle Weight Rating kg (48, lb) Wheelbase cm (232 in) Cab to Axle/trunnion (CA/CT) cm (4 in) Frame Section Modulus (SM) under crane: (758 MPa 11, PSI) cm 3 (2 in 3 ) Frame Section Modulus (SM) over rear stabilizers: (758 MPa 11, PSI) cm 3 (13 in 3 ) Stability Weight, Front kg (77 lb) minimum* Stability Weight, Rear kg (1,5 lb) minimum* Estimated Average Final Weight kg (3,6 lb) Allows the installation of the Model 6E2 on a chassis. In most cases, the chassis will not require reinforcing, and the amount of counterweight required is minimized, increasing payload capacities. Extended front frame rails required for SFO installation kg (65 lb) MIN 76 mm (66") MIN 3692 mm (156") MIN CWT 439 kg (95 lb) MIN 1956 mm (77") MIN SRO Configuration 3 with Torsion Box Rear Mount Working area Gross Axle Weight Rating Front kg (12, lb) Gross Axle Weight Rating Rear kg (34, lb) Gross Vehicle Weight Rating kg (46, lb) Wheelbase cm (222 in) Cab to Axle/trunnion (CA/CT) cm (156 in) Frame Section Modulus (SM) under crane: (758 MPa 11, PSI)... 2 cm 3 (15.9 in 3 ) Frame Section Modulus (SM) over rear stabilizers: (758 MPa 11, PSI) cm 3 (15.9 in 3 ) Stability Weight, Front kg (65 lb) minimum* Stability Weight, Rear kg (95 lb) minimum* Estimated Average Final Weight kg (28,75 lb) Notes: Gross Vehicle Weight rating (GVWR) is dependent on all components of the vehicle (axles, tires, springs, frame, etc.) meeting manufacturers recommendations: always specify GVWR when purchasing trucks Diesel engines require a variable speed governor and energize-to-run fuel solenoid for smooth crane operation; electronic fuel injection requires EET engine remote throttle All mounting data is based on a National Series 6E2 with an 85% stability factor The complete unit must be installed in accordance with factory requirements, and a test performed to determine actual stability and counterweight requirements per SAE J765; contact the factory for details Transmission neutral safety interlock switch is required with optional remote control *Estimated axle scale rates prior to installation of crane, stabilizers and subbase for 85% stability. Series 6E2 5
6 Specifications Boom and jib combinations data Available in six basic models: Model 638E2 Equipped with a 4,88 m - 11,58 m ( ft - 38 ft) three-section boom. Maximum tip height is 14,63 m (48 ft) (no jib option available). 4,88 m - 11,58 m ( ft - 38 ft) three-section boom Model 649E2 Equipped with a 4,88 m - 15 m ( ft - 49 ft) four-section boom. Maximum tip height is 17,98 m (59 ft). 4,88 m - 15 m ( ft - 49 ft) four-section boom (no jib option available). Model 66E2 Equipped with a 7,12 m - 18,3 m (24 ft - 6 ft) three-section boom. Maximum tip height is 21,3 m (7 ft) (no jib option available). 7,2 m - 18,3 m (24 ft - 6 ft) three-section boom Model 671E2 Equipped with a 8,23 m - 21,64 m (27 ft - 71 ft) three-section boom. This model can be equipped with a 7,62 m - 13,72 m (25 ft - 45 ft) two-section jib. Maximum tip height with 13,72 m (45 ft) jib is 38,25 m (125 ft). 8,23 m - 21,64 m (27 ft - 71 ft) three-section boom 6FJ45M 7,62 m - 13,72 m (25 ft - 45 ft) two-section jib Model E2 Equipped with a 7,32 m - 24,38 m (24 ft - 8 ft) four-section boom. Maximum tip height is 27,44 m (9 ft) (no jib option available). 7,32 m - 24, 38 m (24 ft - 8 ft) four-section boom Model 69E2 Equipped with a 8,23 m - 27,43 m (27 ft - 9 ft) four-section boom. This model can be equipped with a 7,62 m - 13,72 m (25 ft - 45 ft) two section jib. Maximum tip height with 13,72 m (45 ft) jib is 43,95 m (144 ft). 8,23 m - 27,43 m (27 ft - 9 ft) four-section boom 6FJ45M 7,62 m - 13,72 m (25 ft - 45 ft) two-section jib Note: Maximum tip is measured with outriggers/stabilizers fully extended. 6
7 Specifications 6E2 winch data All winch pulls and speeds are shown on the fourth layer. 1 part line 2 part line 3 part line 4 part line 5 part line 6 part line Winch line pulls would increase on the first and second layers. Winch line pulls may be limited by the winch capacity or the ANSI 5 to 1 cable safety factor, shown below this chart. Hook blocks are rated at maximum capacity for the block. Do not exceed rated cable pull with any block. Winch Cable supplied Average breaking strength Max pull Max pull Max pull Max pull Max pull Max pull Standard planetary winch 9/ in diameter rotation resistant kg (38,5 lb) 3492,66 kg (77 lb) 6985,32 kg (15,4 lb) 1 477,98 kg (23,1 lb) 13 97,65 kg (3,8 lb) ,96 kg (38,5 lb) ,96 kg (4, lb) Winch pull Winch speed BOS winch speed Rope capacity Layer kg lb mpm fpm mpm fpm m ft , Note: All ratings based on 128,7 LPM at 22,75 MPa (34 GPM at 33 psi) Burst of Speed maximum bull = 13 kg (3 lb) Winch Bare drum pull Allowable cable pull With standard rotation resistant rope 4627 kg (1,2 lb) 3493 kg (77 lb) Loadline deduct Block type Rating Weight Downhaul weight 3,49 t (3.85 USt) kg (15 lb) 1-sheave block 1,48 t (11. USt) 91 kg (2 lb) 2-sheave block 17,46 t (19.25 USt) 1 kg (5 lb) Series 6E2 7
8 Capacities Series 638E2: 11,58 m (38 ft) boom National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET A B 2 4 RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load chart RADIUS (ft) ft 4, 36,15 3,25 25,6 21,9,75 1, A 24 ft 28, 24,3 2,9 18,15,2 14,2 12, B 31 ft 27,5 23,45 2,15 17,8 15,8 14,15 12,9 1, ft 25,75 22,2 19,2 17,5 15,2 13,75 12, NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. 8 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
9 Capacities Series 649E2: 15 m (49 ft) boom National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET A B C RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load chart RADIUS (ft) ft 4, 29,6 24,7 2,4 13, A 25 ft 38,1 27,4 23,2 2,2 17,75 15,75 12, B 33 ft 26,2 22,2 19,25 17, 15,2 12, C 41 ft 25,3 21,3 18,45,3 14, 12, ft 19,5 17,5 15, 13,75 11, , NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. Series 6E2 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 9
10 Capacities Series 66E2: 18,3 m (6 ft) boom National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET A B C RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load chart RADIUS (ft) 24 ft A 33 ft B 42 ft C 51 ft 6 ft , 27,2 22,8 19,65 17,15 15,15 11, ,8 21,6 18,7,4 14,6 11, , 2,7 17,8 15,75 14,5 11, ,4 17,4 15,25 13,6 11, ,15 14,95 13,2 1, NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. 1 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
11 Capacities Series 671E2: 21,64 m (71 ft) boom National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET A B C D RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load chart RADIUS (ft) 28 ft A ft B 44 ft C 53 ft D 62 ft 71 ft , 26,15 21,6 18,5,6 14,9 11, ,2 21,45 18,4, 14,2 11, ,6 2,8 17,8 15,85 14, 11, ,4 17,45 15,3 13, 11, ,8 14,65 13, 1, ,65 1, NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. Series 6E2 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 11
12 Capacities Series 671E2: 21,64 m (71 ft) boom with 13,72 m (45 ft) jib National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET 2 nd Jib 45' 1 st Jib 25' Do not 2 extend jib into 1 this area A B C D RADIUS IN FEET HEIGHT IN FEET Load chart CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Note: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths. 12 RADIUS (ft) ft 4, 25, 21, 17,9, 14,3 11, A ft 24,75 21, 17,95 15, 13,7 11, B 44 ft 24,25 2,45 17,45 15,5 13,65 1, C 53 ft 2,1 17,15 15, 13,25 1, D 62 ft, 14,4 12,75 1, ft 12,45 12,45 1, NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane ft JIB ft JIB
13 Capacities Series E2: 24,38 m (8 ft) boom National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET A B C D RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load chart RADIUS (ft) 24 ft A 36 ft B 47 ft C 58 ft D 69 ft 8 ft , 27,1 22,4 19,5 17,1 14,75 11, ,4 21,4 18,, 14,2 11, ,6 17, 15,3 13, 11, ,5 14,75 13,5 1, ,15 1, NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. Series 6E2 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 13
14 Capacities Series 69E2: 27,43 m (9 ft) boom National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET A -1 B C D RADIUS IN FEET HEIGHT IN FEET CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Load chart RADIUS (ft) 27 ft A 41 ft B 54 ft C 66 ft D 78 ft 9 ft , 25,75 21,4 18,45,4 14,75 11, ,95 17,75 15,25 13,3 1, , 15, 13,2 1, ,45 12, NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. 14 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
15 Capacities Series 69E2: 27,43 m (9 ft) boom with 13,72 m (45 ft) jib National Crane will send you a chart on request or you may secure needed load rating information through your nearest National Crane dealer. LENGTH IN FEET 2 nd Jib 45' 1 st Jib 25' Do not extend 3 jib into this area A -1 B C D RADIUS IN FEET HEIGHT IN FEET Load chart CAUTION: Do not operate crane booms, jib extensions, any accessories or loads within 3 m (1 ft) of live power lines or other conductors of electricity. Jib and boom capacities shown are maximum for each section. Do not exceed capacities at reduced radii Load ratings shown on the load rating charts are maximum allowable loads with the outriggers properly extended on a firm, level surface and the crane leveled and mounted on a factory recommended truck. Always level the crane with the level indicator located on the crane. The operator must reduce load to allow for factors such as wind, ground conditions, operating speeds and their effects on freely suspended loads. Overloading this crane may cause structural collapse or instability. Weights on any accessories attached to the boom or loadline must be deducted from the load chart capacities. Do not exceed jib capabilities at any reduced boom lengths. Do not deadhead lineblock against boom tip when extending boom or winching up. Keep at least three wraps of loadline on drum at all times. Use only specified cable with this machine. Note: 1. Operate with jib by radius when main boom is fully extended. If necessary increase boom angle to maintain loaded radius. 2. Operate with jib by boom angle when main boom is not fully extended. Do not exceed rated jib capacities at any reduced boom lengths. RADIUS (ft) ft 4, 25,2 2,8 17,85 15,8 14,15 1, A 41 ft 2, 17, 14,85 12,9 1, B 54 ft,7 14,7 12,9 1, C 66 ft 14,25 12, D 78 ft ft ft JIB ft JIB NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. Series 6E2 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 15
16 Dimensions Dimensions are in mm (in) unless otherwise specified..5 x 5.8 (1.38 x 2.) Full R TYP 8X Slot 38 (1.5) TYP 143 (5.62) TYP 73 (2.88) TYP 173 (42.25) Scale: 1/12 17 (42.13) Maintain clearance for R1144 (R45.) Tailswing 533 (21.) 18 (138.5) 1132 (44.5) 38' boom: 8.5" Retracted/38' Extended (5,1 m - 11,6 m) 49' boom: ' Retracted/49' Extended (4,88 m - 15 m) 6' boom: 24' Retracted/6' Extended (7,2 m - 18,3 m) 71' boom: 27' 7" Retracted/71' Extended (8,41 m - 21,64 m) 8' boom: 24' Retracted/8' Extended (7,3 m - 24,4 m) 9' boom: 27' 1" Retracted/9' Extended (8,48 m - 27,43 m) G 8. 3 ( ) 9.95 Ground penetration 278 (11.) 667 (26.25) 2387 (94.) 1833 (72.) 292 (11.5) 2343 (92.25) 959 (37.75) 2156 (85.) 1777 (7.) 278 (11.) 4 (18.) 1256 (49.5) Frame height 978 (38.5) 386 (121.5) Ground Level 119 (4.) 1218 (48.) 46 (.) 338 (13.25) 548 (21.5) 176 (42.5) 1275 (5.25) Weight includes all items except Ash 363 kg (83 lb) and bed. Series Retracted length Extended length Subbase G (wet) Dry/Wt With oil/ wt 638E2 5,1 m ( ft 7 in) 11,7 m (38 ft 3 in) 5,5 m (18 ft) 1,23 m (48.3 in) 92 kg (13,651 lb) 6462 kg (14,246 lb) 649E2 4,9 m ( ft) 14,9 m (49 ft) 5,5 m (18 ft) 1,28 m (5.7 in) 6481 kg (14,289 lb) 6751 kg (14,884 lb) 66E2 7,3 m (24 ft) 18,3 m (6 ft) 5,5 m (18 ft) 1,52 m (59.9 in) kg (14,876 lb) 718 kg (15,471 lb) 671E2 8,4 m (27 ft 7 in) 21,6 m (71 ft) 6,1 m ( 2 ft) 1,9 m (.7 in) 7181 kg (15,831 lb) 51 kg (,426 lb) E2 7,3 m (24 ft) 24,4 m (8 ft) 5,5 m (18 ft) 1,71 m (67.5 in) 7256 kg (15,996 lb) 7526 kg (,591 lb) 69E2 8,5 m (27 ft 1 in) 27,4 m (9 ft) 6,1 m (2 ft) 1,98 m (78.1 in) 77 kg (,976 lb) 797 kg (17,571 lb) Subbase Weight C.G. length Standard 18 ft 1229 kg (271 lb) 2,87 m (113 ft) Standard 2 ft 1345 kg (2965 lb) 2,87 m (113 ft) Standard 22 ft 1444 kg (3184 lb) 3,18 m (125 ft) Subbase C.G. are located from center of rotation THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
17 Accessories Radio Remote Controls Eliminate the handling and maintenance concerns that accompany cabled remotes. Operate to a range of about 76 m (25 ft), varying with conditions. Heavy-duty Personnel Basket 12 lb (544 kg) capacity steel basket with safety loops for two passengers. Gravity leveling 183 cm x 17 cm (72 in x 42 in) platform. Fast attachment and secure locking systems. Load chart must show 143 kg (23 lb) minimum to operate this accessory. Duty Cycle Package Burst-of-Speed winch control option, with dual stand up control and hydraulic oil cooler, self-contained radiator system with electric fan. Continuous Rotation Allows rotation of turret/boom without rotation stop. Single Front Outrigger Center mount front stabilizer for 36 stability with a 25 in vertical stroke. Bulkhead Options Steel 3 in solid wall bulkhead Spanish-Language Danger Decals, Control Knobs, and Operators Manuals RB4R BSA-1 BSA-R1 (provides rotation) DCPKG CR SFO BHSD SDD SOM Series 6E2 17
18 18 Notes
19 Notes Series 6E2 19
20 Manitowoc Cranes Regional headquarters Americas Manitowoc, Wisconsin, USA Tel: Fax: Shady Grove, Pennsylvania, USA Tel: Fax: Europe, Middle East, Africa Dardilly, France Tel: +33 () Fax: +33 () China Shanghai, China Tel: Fax: Greater Asia-Pacific Singapore Tel: Fax: Regional offices Americas Brazil Alphaville Mexico Monterrey Chile Santiago Europe, Middle East, Africa France Baudemont Cergy Decines Germany Langenfeld Italy Lainate Netherlands Breda Poland Warsaw Portugal Baltar Russia Moscow South Africa Johannesburg U.A.E. Dubai U.K. Buckingham China Beijing Chengdu Guangzhou Xian Greater Asia-Pacific Australia Brisbane Melbourne Sydney India Chennai Delhi Hyderabad Pune Korea Seoul Philippines Makati City Singapore Factories Brazil Passo Fundo China TaiAn Zhangjiagang France Charlieu Moulins Germany Wilhelmshaven India Pune Italy Niella Tanaro Portugal Baltar Fânzeres USA Manitowoc Port Washington Shady Grove This document is non-contractual. Constant improvement and engineering progress 214 Manitowoc Form No.6E2 PG Part No.6E2 /414 / PDF
GIUFFRE.COM. National Crane 500E2 Series GIUFFRE BROS CRANES INC. Product Guide
National Crane 5E2 Series Product Guide Features 16,3 t (18 USt) rating 21,6 m (71 ft) three-section boom Self-lubricating Easy Glide wear pads Internal anti-two block Features National Crane Series 5E2
More informationNational Crane Series 800D Product Guide ASME B30.5 Imperial 85%
National Crane Series 8D Product Guide ASME B3.5 Imperial 85% Features 2,87 t (23 USt) rating 3,48 m (1 ft) four-section boom Self-lubricating Easy Glide wear pads Internal Anti-Two Block Features National
More informationNational Crane 400B Series
National Crane 4B Series Product Guide Features 17,1 m (56 ft) three-section boom 9,1 t (1 USt) rating Self-lubricating Easy Glide wear pads Internal anti-two block Features National Crane Series 4B 9,7
More informationNational Crane Series 300C
National Crane Series 3C Product Guide Features 7,3 t (8 USt) rating 14, m (46 ft) three-section boom Self-lubricating Easy Glide wear pads Internal anti-two-block Features National Crane Series 3C 7,3
More informationNational Crane 600H Series
National Crane 6H Series Product Guide Features 18,1 t (2 USt) rating Six boom options available from 11,58 m (38 ft) to 27,42 m (9 ft) Full-, mid-, and retracted-span outriggers Mentor LMI System Internal
More informationNational Crane Series NBT15
National Crane Series NBT15 Product Guide Features 13,4 t (15 USt) rating 18,3 m (60 ft) three-section boom Self-lubricating Easy Glide wear pads Internal anti-two block Load sense hydraulics Radio remote
More informationNational Crane Series 1300A
National Crane Series 1300A Product Guide ASME B30.5 Imperial 85% Features 27,2 t (30 USt) rating 33,52 m (110 ft) four-section boom Self-lubricating Easy Glide wear pads Internal anti-two-block Vision
More informationNational Crane Series 1400H Product Guide
National Crane Series 14H Product Guide Features 29,9 t (33 USt) rating 38,72 m (127 ft) five-section boom Self-lubricating Easy Glide wear pads Internal anti-two-block Features National Crane 14H 29,9
More informationNational Crane Series 800H
National Crane Series 8H Data Sheet Features 3,48 m (1 ft) four-section boom 2,86 t (23 USt) rating Self-lubricating Easy Glide wear pads Dimensions 85 mm (31.69") 247 mm (94.") Maximum transport width
More informationNational Crane 600H Series
National Crane 6H Series Product Guide Features 18,1 t (2 USt) rating Six boom options available from 11,58 m (38 ft) to 27,42 m (9 ft) Full-, mid-, and retracted-span outriggers Mentor LMI System Internal
More informationNational Crane Series 1400H
National Crane Series 14H Product Guide Features 29,9 t (33 USt) rating 38,72 m (127 ft) five-section boom Self-lubricating Easy Glide wear pads Internal anti-two-block Features National Crane 14H 29,9
More informationNational Crane Series 1400A
National Crane Series 14A Product Guide ASME B3.5 Imperial 85% Features 29,9 t (33 USt) rating 38,72 m (127 ft) five-section boom Self-lubricating Easy Glide wear pads Internal anti-two-block Vision cab
More informationSeries 500E. product guide. contents. features. All New Design. Features 2. 71' Three-Section Boom. 18 Ton Rating. Mounting Configurations 3
Series product guide features All New Design 71' Three-Section Boom 18 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block Auxiliary Stabilizers Variable Displacement Hydraulic System
More informationSeries 600E. product guide. contents. features. All New Design. Features 2. 90' Four-Section Boom. 20 Ton Rating. Mounting Configurations 3
Series 6E product guide features All New Design 9' Four-Section Boom 2 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block Auxiliary Stabilizers Variable Displacement Hydraulic System
More informationSeries 900A. product guide. contents. features. 103' Four-Section Boom. Features Ton Rating. Self-lubricating Easy Glide Wear Pads
Series 9A product guide features 13' Four-Section Boom 26 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:
More informationNational Crane Series 1400H
National Crane Series 1400H Product Guide Features 29,9 t (33 USt) rating 38,72 m (127 ft) five-section boom Self-lubricating Easy Glide wear pads Internal anti-two-block Features National Crane 1400H
More informationNational Crane Series 1100
National Crane Series 1100 Product Guide Features ř 25,4 t (28 USt) rating ř 32,0 m (105 ft) four-section boom m ř Self-lubricating Easy Glide wear ar pads Features National Crane 1100 Four-section boom
More informationSeries 900A. product guide. contents. features. 103' (31.4 m) Four-Section Boom. Features Ton (23.6 mt) Rating
Series 9A product guide features 13' (31.4 m) Four-Section Boom 26 Ton (23.6 mt) Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block contents Features 2 Mounting Configurations 3 Specifications
More informationNATIONAL MODEL 990A - 26 TON CAPACITY
LIFTING CHARTS - Boom Trucks NATIONAL MODEL 99A - 26 TON CAPACITY Load Chart Rating: Series 99A (27.4 m) Boom with 44 ft. (13.4 m) Jib 2ND JIB 44FT 1ST JIB 25FT LENGTH IN FEET 9 54 27-1 2 8 7 6 A B C D
More informationSeries 400B. product guide. contents. features. 56' Three-section boom. Features Ton rating. Internal anti-two-block. Mounting Configurations 3
Series 4B product guide features 56' Three-section boom 1 Ton rating Internal anti-two-block Self-lubricating Easy Glide wear pads contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:
More informationSeries 400B. product guide. contents. features. 56' Three-Section Boom. Features Ton Rating. Internal Anti-two-block. Mounting Configurations 3
Series 4B product guide features 56' Three-Section Boom 1 Ton Rating Internal Anti-two-block Self-lubricating Easy Glide Wear Pads contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:
More informationNational Crane Series NBT30H
National Crane Series NBT30H Product Guide Features 27,2 t (30 USt) rating 33,52 m (110 ft) four-section boom All new design Multi-position Easy Reach control panel Graphical LMI Features National Crane
More informationNational Crane Series NBT45
National Crane Series NBT45 Product Guide Features ř 40,8 t (45 USt) rating ř 43,3 m (142 ft) five-section boom ř Self-lubricating Easy Glide wear pads ř 2041 kg (4500 lb) tailswing counterweight Features
More informationNational Crane Series NBT50
National Crane Series NBT50 Preliminary Product Guide Features 31,1 m (102 ft) four-section full power boom and optional 39,01 m (128 ft) five-section full power boom 45,36 t (50 USt) at 2,44 (8 ft) and
More informationNational Crane 1800 Series
National Crane 1800 Series Product Guide Features 36,29 t (40 USt) rating 43,28 m (142 ft) five-section boom (80 ft) Self-lubricating Easy Glide wear pads Tailswing counterweight Features Outriggers Outrigger
More informationSeries 1400A. product guide. contents. features. Features ' (38.72 m) Five-Section Boom. Mounting Configurations Ton (29.
Series 14A product guide features 127' (38.72 m) Five-Section Boom 33 Ton (29.9 mt) Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block NEW VISION CAB contents Features 2 Mounting Configurations
More informationNational Crane Series NBT36
National Crane Series NBT36 Product Guide Features 32,7 t (36 USt) rating 38,7 m (127 ft) five-section boom Self-lubricating Easy Glide wear pads Features National Crane Series NBT36 32,7 t (36 USt) maximum
More informationNational Crane Series NBT50
National Crane Series NBT50 Preliminary Product Guide Features 31,1 m (102 ft) four-section full power boom and optional 39,01 m (128 ft) five-section full power boom 45,36 t (50 USt) at 2,44 (8 ft) and
More informationSeries product guide. contents. features. View thousands of Crane Specifications on FreeCraneSpecs.com. 127 ft (38.70 m) Five-Section Boom
Series 15 product guide features 127 ft (38. m) Five-Section Boom 36 USt (32.66 t) Rating Easy Glide Wear Pads contents Features 2 Mounting Configurations 3 Specifications 4 Capacities 5 Accessories 9
More informationSeries 1300A. product guide. contents. features. All New Design. Features ' Four-Section Boom. Mounting Configurations 3.
Series product guide features All New Design 110' Four-Section Boom 30 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-twoblock NEW VISION CAB contents Features 2 Mounting Configurations
More informationPotain Igo 50 Product Guide
Potain Igo 5 Product Guide Features 4 kg (8818 lb) maximum capacity 1 1 kg () capacity at 131 ft (4 m) 4 m (131 ft) maximum operating hook radius 33,8 m (111 ft) maximum hook height with jib set at 2 23,2
More informationPotain Igo T 130 Product Guide
Potain Igo T 1 Product Guide Features 8 kg (17,637 ) maximum capacity 1 kg (86 ) capacity at 5 m (16 ) 5 m (16 ) maximum operating hook radius 37,3 m (1 ) maximum tip hook height with jib horizontal 61
More information600H Product Guide. Features. ASME B30.5 Imperial 85% Standard RCL System. 18,1 t (20 USt) rating
6H Product Guide ASME B3.5 Imperial 85% Features 18,1 t (2 USt) rating Five boom options available from 15 m (49 ft) to 27,42 m (9 ft) Multiple outrigger positions Standard RCL System Internal anti-two
More information400B Product Guide. Features. ASME B30.5 Imperial 85% 9,1 t (10 USt) rating. Multiple mounting configurations. 17,1 m (56 ft) three-section boom
4B Product Guide ASME B3.5 Imperial 85% Features 9,1 t (1 USt) rating 17,1 m (56 ft) three-section boom Multiple mounting configurations Internal anti-two block NATIONAL CRANE 4B The 4B Series delivers
More informationPotain HDT 80 Product Guide
View View thousands thousands of of Crane Crane Specifications Specifications on on FreeCraneSpecs.com FreeCraneSpecs.com Potain HDT 80 Product Guide Features 6000 kg (13,228 ) maximum capacity 1350 kg
More information1300 kg (2866 lb) capacity at 40 m (131 ft) 40 m (131 ft) maximum operating hook radius. 44,5 m (146 ft) maximum hook height with jib set at 30
Potain Igo T 70 Product Guide Features 4000 kg (8818 lb) maximum capacity 1300 kg (2866 lb) capacity at 40 m (131 ft) 40 m (131 ft) maximum operating hook radius 44,5 m (146 ft) maximum hook height with
More informationGrove GMK6350. Product Guide. Features. 15,5 m - 60 m (51 ft ft) five-section full power MEGAFORM boom
Grove GMK6350 Product Guide Features 15,5 m - 60 m (51 ft - 197 ft) five-section full power MEGAFORM boom 11 m - 19 m (36 ft - 62 ft) telescoping offsettable swingaway extension 21 m - 61 m (69 ft - 200
More informationShuttlelift CD5520 Product Guide
Shuttlelift CD552 Product Guide Features 18 t (2 USt) capacity 16,6 m (54.5 ft) four-section, four-plate full power boom 9,7 t (1 USt) deck carrying capacity Exclusive pivoting boom nose Features Steering
More informationGrove YB5520 Product Guide ASME B30.5 Imperial 85%, Metric 85% and DIN/ISO
Grove YB552 Product Guide ASME B3.5 Imperial 85%, Metric 85% and DIN/ISO Features 18 t (2 USt) capacity 16,6 m (54.5 ft) four-section, four-plate full power boom 9,7 t (1 USt) deck carrying capacity Exclusive
More informationShuttlelift CD5520 Product Guide
Shuttlelift CD552 Product Guide Features 1 t (2 USt) capacity 16,6 m (54.5 ft) four-section, four-plate full power boom 9,7 t (1 USt) deck carrying capacity Exclusive pivoting boom nose Features Steering
More informationGrove YB5515 (Dual Fuel)
Grove YB5515 (Dual Fuel) Product Guide Features 13,6 t (15 USt) capacity threesection boom with 12,5 m (41 ft) outreach 4,6 m (15 ft) offsettable swingaway extension 9072 kg (20,000 lb) deck carrying capacity
More informationShuttlelift CD5540F (Dual Fuel) Product Guide
Shuttlelift CD55F (Dual Fuel) Product Guide Features 13, t (15 USt) capacity threesection boom with 1,5 m (1 ft) outreach, m (15 ft) offsettable swingaway extension 97 kg (, lb) deck carrying capacity
More informationPotain Igo T 85 A Product Guide
Potain Igo T A Product Guide Features 6 (13,2 ) axiu capacity 1 (86 ) capacity at (18 ) (18 ) axiu operating hook radius 51 (167 ) axiu hook height with (18 ) jib set at 38 (125 ) axiu tip hook height
More informationIgo T 85. Preliminary. product guide. contents. features. Features 2. Specifications 3. Transport 4. Weights 5. Dimensions 6.
Preliminary product guide contents Features 2 Specifications 3 Transport 4 Weights 5 Dimensions 6 features 13,228 lb (6 000 kg) maximum capacity 2,756 lb (1 250 kg) capacity at 148 ft (45 m) 148 ft (45
More informationProduct Guide ASME B30.5 Imperial 85%
Grove RT9150E Product Guide ASME B30.5 Imperial 85% Features 135 t (150 USt) rating 12,9 m - 60,0 m (42 ft - 197 ft) six-section, full power pin boom 11 m -18 m (36 ft - 59 ft) offsettable bi-fold swingaway
More informationPotain MD. Range. Characteristics. Max. jib: 62,5 à 80,0 m Max. load: 10,0 à 40,0 t Tip load: 2,0 à 5,4 t Mast: 1,60 à 2,45 m Hoist: 33 à 150 LVF
Potain MD Range Characteristics Max. jib: 62,5 à 80,0 m Max. load: 10,0 à 40,0 t Tip load: 2,0 à 5,4 t Mast: 1,60 à 2,45 m Hoist: 33 à 150 LVF Considered to be the parent range to tower cranes, MD cranes
More informationGrove rough-terrain cranes. Features and benefits
Grove rough-terrain cranes Features and benefits Grove is a leading manufacturer of the industry s most reliable cranes. The full line of Grove mobile hydraulic cranes ranges from 8 t to 450 t, (8.5 USt
More informationGrove RT540E. Product Guide. Features. 35 t (40 USt) capacity. 9,8 m 31 m (32 ft 102 ft) foursection
Grove RT5E Product Guide Features t ( USt) capacity 9,8 m 31 m (32 ft 102 ft) foursection full power boom 7,9 m 13,7 m (26 ft ft) offsettable telescopic swingaway extension Dual-axis electric joystick
More informationGrove RT600E Product Guide
Grove RT600E Product Guide ASME B30.5 Imperial 85% Features 10 m - 32 m (33 ft - 105 ft) four-section full-power boom 8,8 m 15,5 m (29 ft 51 ft) telescopic swingaway extension Maximum main boom tip height
More informationGrove GMK6300L North American Product Guide
Grove GMK6300L North American Product Guide Features 350 USt capacity 15,6 m - 80 m (51 ft - 263 ft) seven-section full power MEGAFORM boom with TWIN-LOCK pinning 12 m - 21 m (39 ft - 69 ft) hydraulic
More informationGrove RT600E. Product Guide. Features. View thousands of Crane Specifications on FreeCraneSpecs.com
Grove RT600E Product Guide Features 10 m - 32 m (33 ft - 105 ft) four-section full power boom 8,8 m 15,5 m (29 ft 51 ft) telescopic swingaway extension Maximum main boom tip height of 34 m (112 ft) Maximum
More informationShuttlelift CD7725. Product Guide. Features. 22 t (25 USt) capacity. 21,6 m (71 ft) four-section full power boom
Shuttlelift CD7725 Product Guide Features 22 t (25 USt) capacity 21,6 m (71 ft) four-section full power boom 13,6 t (15 USt) deck carrying capacity Tilt steering wheel Load sensing piston hydraulic pump
More informationGrove RT9150E. Provisional Product Guide
Grove RT9150E Provisional Product Guide Features 135 t (150 USt) capacity 12,9 m - 60,0 m (42 ft - 197 ft) six-section, full power boom 11 m -18 m (36 ft - 59 ft) offsettable bi-fold swingaway extension
More informationShuttlelift CD7725. Product Guide. Features. 22 t (25 USt) capacity. 21,6 m (71 ft) four-section full power boom
Shuttlelift CD7725 Product Guide Features 22 t (25 USt) capacity 21,6 m (71 ft) four-section full power boom 13,6 t (15 USt) deck carrying capacity Tilt steering wheel Load sensing piston hydraulic pump
More informationGrove YB7725. Product Guide. Features. 22 t (25 USt) capacity. 21,6 m (71 ft) four-section full power boom. 13,6 t (15 USt) deck carrying capacity
Grove YB7725 Product Guide Features 22 t (25 USt) capacity 21,6 m (71 ft) four-section full power boom 13,6 t (15 USt) deck carrying capacity Tilt steering wheel Load sensing piston hydraulic pump Proportional
More informationGrove RT540E. Product Guide. Features. 35 t (40 USt) capacity. 9,8 m 31 m (32 ft 102 ft) four-section full power boom
Grove RT5E Product Guide Features t ( USt) capacity 9,8 m 31 m (32 ft 102 ft) four-section full power boom 7,9 m 13,7 m (26 ft ft) offsettable telescopic swingaway extension Dual-axis electric joystick
More informationPotain MDT CITY. Range Brochure. Model Max. load Max. jib Tip load Mast Hoist. MDT98 6 t 55 m 1,2 t to 55 m 3,8-4,5 m 25 & 33 ch
Potain MDT CITY Range Brochure Model Max. load Max. jib Tip load Mast Hoist MDT98 6 t 55 m 1,2 t to 55 m 3,8-4,5 m 25 & 33 ch MDT128 6 t 55 m 1,6 t to 55 m 3,8-4,5 m 25, 33 & 50 ch MDT178 8 t 60 m 1,5
More informationProduct Guide. Features. Tilt steering wheel. Load sensing piston hydraulic pump. Proportional hydraulic controls
Grove YB7725 Product Guide Features 22 t (25 USt) capacity 21,6 m (71 ft) four-section full power boom 13,6 t (15 USt) deck carrying capacity Tilt steering wheel Load sensing piston hydraulic pump Proportional
More informationGrove RT770E. Product Guide. Features. full power boom. 10,1 m - 17,1 m (33 ft - 56 ft) offsettable bi-fold lattice swingaway extension
Grove RT770E Product Guide Features 65 t (70 USt) capacity 11 m 42 m (36 ft 138 ft) five-section full power boom 10,1 m - 17,1 m (33 ft - 56 ft) offsettable bi-fold lattice swingaway extension 6,1 m (20
More informationGrove GMK6400. North American Provisional Product Guide. Features. 450 USt rating. 15,4 m - 60 m (51 ft ft) five-section boom
Grove GMK6400 North American Provisional Product Guide Features 450 USt rating 15,4 m - 60 m (51 ft - 197 ft) five-section boom 79 m (259 ft) luffing jib New self-rigging MegaWingLift 135 t (297,000 lb)
More informationManitowoc Product Guide ASME B30.5 Metric / Imperial
Manitowoc 8500-1 Product Guide ASME B30.5 Metric / Imperial Features 80,0 t (85 USt) capacity 61 m (200 ft) heavy-lift boom Max boom + jib combination: 54,9 m (180 ft) + 18,3 m (60 ft) 213 kw (285 P) engine
More informationGrove YB7725 Product Guide
Grove YB77 Product Guide Features 22 t ( USt) capacity 21,6 m (71 ft) four-section full power boom 13,6 t (15 USt) deck carrying capacity Tilt steering wheel sensing piston hydraulic pump Proportional
More informationGrove RT530E-2. Product Guide. Features. 30 t (30 USt) capacity. 8,8 m 29,0 m (29 ft 95 ft) four-section full power boom
Grove RT5E-2 Product Guide Features t ( USt) capacity 8,8 m 29,0 m (29 ft 95 ft) four-section full power boom 7,9 m - 13,7 m (26 ft - 45 ft) offsettable telescopic swingaway extension Dual-axis electric
More informationGrove RT770E. Product Guide. Features. 65 t (70 USt) capacity. 11 m 42 m (36 ft 138 ft) five-section full power boom
Grove RT770E Product Guide Features 65 t (70 USt) capacity 11 m 42 m (36 ft 138 ft) five-section full power boom 10,1 m - 17,1 m (33 ft - 56 ft) offsettable bi-fold lattice swingaway extension 6,1 m (20
More informationGrove RT9150E Product Guide
Grove RT9150E Product Guide Features 135 t (150 USt) capacity 12,9 m -,0 m (42 ft - 197 ft) six-section, full power boom 11 m -18 m (36 ft - 59 ft) offsettable bi-fold swingaway extension One 8 m (26 ft)
More informationproduct guide contents features Industrial Hydraulic Crane Features 2 Specifications 3
product guide features 22 ton (19.9 mt) capacity 360 on outriggers @ 8.5 ft. (2.6m) radius 15 ton (13.6 mt) deck carrying capacity 15 ton (13.6 mt) on rubber capacity 43 ft. (13.1m) 3-section boom or 67
More information11 m 18 m (36 ft 59 ft) bi-fold lattice swingaway, hydraulic luffing or manual offset
Grove GMK5135 Product Guide Features 110 t (135 USt) capacity 12,9 m 50,8 m (42 ft 167 ft) five-section full power boom 11 m 18 m (36 ft 59 ft) bi-fold lattice swingaway, hydraulic luffing or manual offset
More informationGrove RT9150E. Product Guide ASME B30.5 Imperial 85% Features. View thousands of Crane Specifications on FreeCraneSpecs.com
Grove RT9150E Product Guide ASME B30.5 Imperial 85% Features 135 t (150 USt) rating 12,9 m - 60,0 m (42 ft - 197 ft) six-section, full power pin boom 11 m -18 m (36 ft - 59 ft) offsettable bi-fold swingaway
More informationBoom truck 36 tons. national series BOOM LENGTHS: 31ft to 127ft JIB LENGTHS: 31ft JIB OFFSETS:
Boom truck 3 tons national series : ft to 7ft JIB : ft JIB OFFSETS: NOTES: portland office: 53.23.11 seattle office: 2.74.4 features Why Buy a National Crane Series? 3 USt (32. t) Rating The provides a
More informationGrove RT530E-2. Product Guide. Features. 30 t (30 USt) capacity. 8,8 m 29,0 m (29 ft 95 ft) four-section full power boom
Grove RT5E-2 Product Guide Features t ( USt) capacity 8,8 m 29,0 m (29 ft 95 ft) four-section full power boom 7,9 m - 13,7 m (26 ft - 45 ft) offsettable telescopic swingaway extension Dual-axis electric
More informationNational Crane Series NBT45 Product Guide
National Crane Series NBT45 Product Guide ASME B.5 Imperial 85% Features,8 t (45 USt) ratg 49,1 m (161 ft) five-section boom Self-lubricatg Easy Glide wear pads 41 kg ( lb) tailswg counterweight Features
More informationGrove GMK3055. Product Guide. Features
Grove GMK3055 Product Guide Features 9,7 m 43 m (32 ft 141 ft) 6-section full power boom Patented TWIN-LOCK boom pinning system 8,7 m 15 m (28.5 ft 49.2 ft) bi-fold lattice swingaway, hydraulic luffing
More informationGrove GMK4115L. Product Guide. Features. 100 t (115 USt) capacity
Grove GMK4115L Product Guide Features 100 t (115 USt) capacity 11,7 m 60 m (38 ft 197 ft) seven-section full power MEGAFORM TM boom with TWINLOCK TM pinning 10 m 17 m (33 ft 56 ft) hydraulic offset bi-fold
More informationShuttlelift CD7725. Product Guide. Features. 22 t (25 USt) capacity. 21,6 m (71 ft) four-section full power boom
Shuttlelift CD7725 Product Guide Features 22 t (25 USt) capacity 21,6 m (71 ft) four-section full power boom 13,6 t (15 USt) deck carrying capacity Tilt steering wheel Load sensing piston hydraulic pump
More informationGrove TMS9000E Product Guide
Grove TMS9000E Product Guide Features 90 t (110 USt) capacity 11,2 m - 43,3 m (36 ft - 142 ft) five-section full power boom Patented TWIN-LOCK boom pinning system 10 m - 17 m (33 ft - 56 ft) bi-fold lattice
More informationGrove RT880E. Product Guide. Features. View thousands of Crane Specifications on FreeCraneSpecs.com
Grove RT880E Product Guide Features 75 t (80 USt) capacity 12,6 m - 39,0 m (41 ft - 128 ft) four-section, full power boom 10,0 m - 17,0 m (33 ft - 56 ft) offsettable lattice swingaway extension 6,1 m (20
More informationSeries 800D. product guide. contents. features. 100' ft (30.48 m) Four-Section Boom. Features USt (20.87 t) Rating. Easy Glide Wear Pads
913.321.7 Series product guide features 1' ft (3.4 m) Four-Section oom 23 USt (2.7 t) Rating Easy Glide Wear Pads Internal nti-two-block contents Features 2 Mounting onfigurations 3 Specifications 4 apacities
More informationGrove RT540E. Product Guide. Features. 35 t (40 USt) capacity. 9,8 m 31 m (32 ft 102 ft) 4-section full power boom
Grove RT5E Product Guide Features t ( USt) capacity 9,8 m 31 m (32 ft 102 ft) 4-section full power boom 7,9 m 13,7 m (26 ft ft) offsettable telescopic swingaway extension Dual-axis electric joystick controllers
More informationGrove RT600E. Product Guide. Features. 10 m - 32 m (33 ft ft) four-section full power boom
Grove RT600E Product Guide Features 10 m - 32 m (33 ft - 105 ft) four-section full power boom 8,8 m 15,5 m (29 ft 51 ft) telescopic swingaway extension Maximum main boom tip height of 34 m (112 ft) Maximum
More informationGrove RT880E. Product Guide. Features
Grove RT880E Product Guide Features 75 t (80 USt) capacity 12,6 m - 39,0 m (41 ft - 128 ft) four-section, full power boom 10,0 m - 17,0 m (33 ft - 56 ft) offsettable lattice swingaway extension 6,1 m (20
More information10 m - 17 m (33 ft - 56 ft) bi-fold lattice swingaway, hydraulic luffing or manual offset
Grove GMK5115 Product Guide Features 100 t (115 USt) capacity 11,7 m - 60 m (38 ft - 197 ft) seven-section full power boom 10 m - 17 m (33 ft - 56 ft) bi-fold lattice swingaway, hydraulic luffing or manual
More informationManitowoc Product Guide. Features
Manitowoc 8000-1 Product Guide Features 80 USt capacity 200 heavy-li boom Max boom + jib combination: 180 + 60 285 P engine 525 fpm maximum line speed 17,000 lb rated line pull Contents Specifications
More informationProduct Guide. Features. four-section full power boom. swingaway extension. swingaway extension
Grove RT700E Product Guide Features 50 t - 55 t (50 USt - 60 USt) capacity 11 m 33,5 m (36 ft 110 ft) four-section full power boom 10,1 m (33 ft) offsettable lattice swingaway extension 10,1 m - 17,1 m
More information11 m - 18 m (36 ft - 59 ft) bi-fold lattice swingaway, hydraulic luffing or manual offset
Grove GMK5165-2 Product Guide ASME B30.5 Imperial 85% Features 130 t (165 USt) capacity 12,9 m - 60 m (42 ft - 197 ft) six-section full power MEGAFORM boom with TWIN-LOCK pinning 11 m - 18 m (36 ft - 59
More informationGrove RT880E. Product Guide. Features
Grove RT880E Product Guide Features 75 t (80 USt) capacity 12,6 m - 39,0 m (41 ft - 128 ft) four-section, full power boom 10,0 m - 17,0 m (33 ft - 56 ft) offsettable lattice swingaway extension 6,1 m (20
More informationGrove TMS700E. Product Guide. Features. Page t or 55 t (50 USt or 60 USt) capacity
Page 1 Grove TMS0E Product Guide Features t or t ( USt or USt) capacity 11 m 33,5 m (36 ft 110 ft) four-section, full power sequenced synchronized boom 10,1 m 17 m (33 ft 56 ft) offsettable bi-fold lattice
More informationProduct Guide. Features. Max boom + jib combination:
Manitowoc 8500-1 Product Guide Features 80,0 t (85 USt) capacity 61 m (200 ft) heavy-lift boom Max boom + jib combination: 54,9 m (180 ft) + 18,3 m (60 ft) 213 kw (285 P) engine 160 m/min (525 fpm) maximum
More informationProduct Guide. Features. 6 ft 110 ft) four-section, full power sequenced synchronized. nchronized boom. swingaway extension.
Grove TMS0E Product Guide Features ř t or t ( USt or USt) capacity ř 11 m 33,5 m (36 6 ft 110 ft) four-section, full power sequenced synchronized nchronized boom ř 10,1 m 17 m (33 33 ft 56 ft) offsettable
More information11 m - 18 m (36 ft - 59 ft) bi-fold lattice swingaway, hydraulic luffing or manual offset
Grove GMK5165-2 Product Guide Features 130 t (165 USt) capacity 12,9 m - 60 m (42 ft - 197 ft) six-section full power MEGAFORM boom with TWIN-LOCK pinning 11 m - 18 m (36 ft - 59 ft) bi-fold lattice swingaway,
More informationShuttlelift CD5500 Series
Shuttlelift CD55 Series Product Guide Features CD55F: 13, t (15 USt) capacity threesection boom with,5 m (41 ft) outreach CD55B: 1,3 t ( USt) capacity foursection boom with 1, m (54 ft in) outreach 4,
More informationGMK4115. product guide. contents. features. All Terrain Crane. 115-ton (100 mt) capacity. Features 2
product guide features 115-ton (100 mt) capacity 37-171 ft. (11.3-52 m) 6 section full power Mega Form boom with Twin Lock pinning 33-56 ft. (10-17 m) hydraulic offset bi-fold swingaway 2 X 16 ft. (5 m)
More informationManitowoc 10000A-1 Product Guide ASME B30.5 Imperial
Manitowoc 10000A-1 Product Guide ASME B30.5 Imperial Features 100 USt capacity 200 heavy-li boom Max boom + jib combination: 190 + 60 285 P engine 535 fpm maximum line speed 25,200 lb rated line pull Features
More informationGrove GMK4115L. Product Guide. Features. 100 t (115 USt) capacity
Grove GMK4115L Product Guide Features 100 t (115 USt) capacity 11,7 m 60 m (38 ft 197 ft) 7 section full power MEGAFORM TM boom with TWINLOCK TM pinning 10 m 17 m (33 ft 56 ft) hydraulic offset bi-fold
More informationGrove GMK5275. Product Guide. Custom Service Crane, Inc. Features. 220 t (275 Ust) capacity
Grove GMK5275 Product Guide Features 220 t (275 Ust) capacity 13,3 m - 68 m (44 ft - 223 ft) seven-section full-power MEGAFORM boom with TWIN-LOCK pinning 12 m - 21 m (39 ft - 69 ft) hydraulic offset bi-fold
More informationGrove RT700E. Product Guide. Features. 50 t - 55 t (50 USt - 60 USt) capacity. 11 m 33,5 m (36 ft 110 ft) four-section full power boom
Grove RT700E Product Guide Features 50 t - 55 t (50 USt - 60 USt) capacity 11 m 33,5 m (36 ft 110 ft) four-section full power boom 10,1 m (33 ft) offsettable lattice swingaway extension 10,1 m - 17,1 m
More informationGrove TMS700E. Product Guide. Features. 50 t or 55 t (50 USt or 60 USt) capacity
Grove TMS700E Product Guide Features 50 t or 55 t (50 USt or 60 USt) capacity 11 m 33,5 m (36 ft 110 ft) four-section, full power sequenced synchronized boom 10,1 m 17 m (33 ft 56 ft) offsettable bi-fold
More informationSeries 1300A Hydraulic Crane 30 Ton Load Ratings
Series 13A Hydraulic Crane 3 Ton Load Ratings DANGER AN UNTRAINED OPERATOR SUBJECTS HIMSELF AND OTHERS TO DEATH OR SERIOUS INJURY YOU MUST NOT OPERATE THIS CRANE UNLESS You have been trained in the safe
More informationGrove YB5500 Series. Product Guide. Features. YB5515: 13,6 t (15 USt) capacity three-section boom with 12,5 m (41 ft) outreach
Grove YB55 Series Product Guide Features YB5515: 13,6 t (15 USt) capacity threesection boom with 12,5 m (41 ft) outreach : 16,3 t (18 USt) capacity foursection boom with 16,6 m (54 ft 6 in) outreach 4,6
More informationManitowoc Product Guide ASME B30.5 Metric / Imperial
Manitowoc 11000-1 Product Guide ASME B30.5 Metric / Imperial Features 100 t (110 USt) capacity 61,0 m (200 ft) heavy-lift boom Max boom + jib combination: 57,9 m (190 ft) + 18,3 m (60 ft) 213 kw (285 P)
More informationSeries 1400A Hydraulic Crane 33 Ton
Series 1A Hydraulic Crane 33 Ton Load Ratings DANGER AN UNTRAINED OPERATOR SUBJECTS HIMSELF AND OTHERS TO DEATH OR SERIOUS INJURY YOU MUST NOT OPERATE THIS CRANE UNLESS You have been trained in the safe
More information