Product Information Packet EM44254T HP,1785RPM,3PH,60HZ,L449T,A44200M,TEF

Transcription

1 Product Information Packet EM44254T HP,1785RPM,3PH,60HZ,L449T,A44200M,TEF Copyright All product information within this document is subject to ABB Motors and Mechanical Inc. copyright protection, unless otherwise noted.

2 Part Detail Revision: P Status: PRD/A Change #: Proprietary: No Type: AC Elec. Spec: A44WG4997 CD Diagram: Mfg Plant: Mech. Spec: Layout: Poles: 04 Created Date: Base: Eff. Date: Leads: 6# P Specs Catalog Number: EM44254T-2340 Frame Prefix: L Enclosure: TEFC Heater Indicator: Heater Included, 120 V Frame: L449T Insulation Class: F Frame Material: Iron Inverter Code: Not Inverter Frequency: HZ IP Rating: NONE Synchronous Frequency: HZ KVA Code: H Frequency: HZ Lifting Lugs: Standard Lifting Lugs HZ Motor Lead Quantity/Wire Size: 6 AWG XP Class and Group: None Motor Type: A44200M XP Division: Not Applicable Mounting Arrangement: F1 Agency Approvals: CCSA US Power Factor: 88 CSA EEV Pulley End Bearing Type: Ball Auxillary Box: Auxillary Box Pulley Face Code: Standard Base Indicator: Rigid Shaft Ground Indicator: No Shaft Grounding Bearing Grease Type: Polyrex EM (-20F +300F) Shaft Rotation: Reversible Voltage: V Shaft Slinger Indicator: Shaft Slinger V Speed Code: Single Speed Design Code: - Motor Standards: Other Page 2 of 18

3 Drip Cover: No Drip Cover Starting Method: Direct on line Duty Rating: CONT Thermal Device - Bearing: NONE (OLD) Feedback Device: NO FEEDBACK Thermal Device - Winding: RTD Only Page 3 of 18

4 Nameplate NP3132L SPEC NO. P44G5953 CAT.NO. EM44254T-2340 FRAME L449T HP 250 VOLTS 2300/4000 PHASE 3 DESIGN - TYPE P RPM 1785 AMPS 56.3/32.4 HZ 60 AMB 40 SF 1.15 DRIVE END BEARING 110BC02J30X DUTY CONT INSUL.CLASS F OPP D.E. BEARING 6318/C3VL0241 ENCL TEFC CODE H NEMA NOM/CSA QUOTED EFF NEMA-NOM-EFFICIENCY 95 SER.NO. MOTOR WEIGHT Page 4 of 18

5 Nameplate AAA EQUIPPED WITH 120V/245W AND 240V/245W SPACE HEATERS 120V HTR= 1H1,1H2 240V HTR= 2H1,2H2 Page 5 of 18

6 Nameplate NP2496L MOBIL POLYREX EM Page 6 of 18

7 Parts List Part Number Description Quantity SA SA P44G EA RA RA P44G EA P 06 AWG,UL3499,BLACK,7.5kV,BELDEN# FT BB EXT. LEAD LUG EA SC N/P EA LABEL, MYLAR EA NP3132L "BALDOR ONLY" INDUSTRIAL MOTOR, SS, EA FF N/P EA VD LABEL WARNING EA AAA N/P BLANK (RELEASE QTY 1,500) EA A GREASE POLYREX EM LB CK HHCS 3/8-16X1L PLATED EA FK HHCS 3/4-10X2-1/2 PLTD EA DK HHCS 1/2-13X3-3/4 PLTD EA DK HHCS 1/2-13X3-3/4 PLTD EA LA SOCKET SET SCREW EA DA KEY 1/4X1/4X1-3/4 L EA AB P/NIP 1/8X9"L Threaded both ends EA BB PIPE NIPPLE,DE BS EA AB CPLG 1/4" PLATED EA AB PPLG 1/4" PLTD EA AB 1/8" NPT SQHDPLG EA DA FAN F EA RA G28 SHORT FAN COVER W/BAFFLE ASSEMBLY EA Page 7 of 18

8 Parts List (continued) Part Number Description Quantity B G28 BRKT WCA EA A WSHR EA AB 1/8" NPT SQHDPLG EA B CLAMP EA A CPLG 1/8 HEX TYPE EA BK HHCS 5/16-18X1/2 PLATED EA BK HHCS 5/16-18X3/4 PLATED EA FK HHCS 3/4-10X2-1/2 PLTD EA AB FLTW BAFFLE EA AB FLTW BAFFLE EA AB P/NIP 1/8X9"L Threaded both ends EA BB PIPE NIPPLE,DE BS EA AB 1/8" NPT SQHDPLG EA AB CPLG 1/4" PLATED EA AB PPLG 1/4" PLTD EA K GASK, 26" LAC EA B G28 BRKT WCA EA D SLGR EA A CPLG 1/8 HEX TYPE EA A G28 AIR DEFLECTOR DRIVE END -- PLASTIC EA A THERMAL BARRIER -- G28 -- BRACKET MTD EA DB HSHCS1/2-13X1-3/4 PLATE EA AB WSHR.531ID 1.062OD EA A G28 C/BOX WCA EA Page 8 of 18

9 A GASKET, G28 LEAD THROAT EA DK HHCS 1/2-13X1 PLATED EA T CONDUIT BOX EA B CBCA WCA EA A +CBOX CVR BLKT - 400/ EA A LEAD GASKET FOR AUX LEADS EA A GASK EA AK HHCS 1/4-20X5/8 PLATED EA D T/PLT EA AK HHCS 1/4-20X1/2 PLATED EA GB SLRHMS 6-32X1/2 PLTD EA EA P/NIP 3/4X4 BLACK EA C T/BLK EA A ALFTG 1/8" 1610-BL EA A ALFTG 1/8" 1610-BL EA A GASKET, TERBD EA A PLUG - FAN COVER EA J TERMINAL LUG - MAKE FROM F EA A GREASE FITTING CAP EA A GREASE FITTING CAP EA G C/B KB EA A C/B EA A PLTE WCA EA B LEAD GASKET FOR AUX LEADS EA C TERBD EA B GASK EA Page 9 of 18

10 H TERBD EA A TERM BLK SPRT AUX FOR 320 AUX BOX EA LB HHTTS 1/4-20X1 PLATED EA CK HHCS 3/8-16X1-1/4 PLTD EA GB SLRHMS 6-32X1/2 PLTD EA FB 1.0 X 5.00 PIPE NIPPLE EA AA BUSH 2 TO 1 BLACK EA MG1025G05 WILKOFAST, , MED. GRAY CHAR. MET GA EA DRSCR #6-1/4 304 S.S EA KA 7/8 SQ X 6.75 KEY EA A RTD TAG EA A N/P GRD I/D EA CL N/P EA Y #3 SLEEVING (GREEN) FT Y #4 SLEEVING (GREEN) PER FT FT NP2496L MOTOR LUBE NAMEPLATE EA /449 WIDE SHIPPING SKID EA D CARRIAGE BOLT EA AB FLAT WASHER 3/8"PLATED EA AB WSHR.562ID 1.375OD EA C PLASTIC BAG 42X32X EA AC HEX NUT, SHIPPING EA LABEL, MYLAR EA Page 10 of 18

11 xt Product Information Packet: EM44254T HP,1785RPM,3PH,60HZ,L449T,A44200M,TEF REL. S.O. AMPS L449T 250 P 3/ / /32.4 CONT 40/F H TEFC E/S FRAME HP TYPE DUTY ROTOR AMB C/ INSUL. S.F. TEST S.O GE /1.25 PERFORMANCE LOAD HP AMPERES RPM NO LOAD 1/4 2/4 3/4 4/4 5/4 LOCKED ROTOR PULL UP BREAKDOWN FULL LOAD PHASE/ HERTZ NEMA DESIGN TEST DATE SPEED TORQUE RPM TORQUE % FULL LOAD RPM CODE LETTER % POWER FACTOR TORQUE LB.-FT. VOLTS ENCL. STATOR RES.@25 C OHMS (BETWEEN LINES) % EFFICIENCY AMPERES Page 11 of 18 AMPERES SHOWN FOR VOLT CONNECTION. IF OTHER VOLTAGE CONNECTIONS ARE AVAILABLE, THE AMPERES WILL VARY INVERSELY WITH THE RATED VOLTAGE REMARKS: TYPICAL DATA DR. BY CK. BY APP. BY DATE A-C MOTOR R.K. BRIDGES W.L. SMITH W.L. SMITH PERFORMANCE 04/30/14 ISSUE DATE 04/30/14 DATA A44WG4997-R001 Printed on 4/30/14 ragsun

12 xt Product Information Packet: EM44254T HP,1785RPM,3PH,60HZ,L449T,A44200M,TEF RPM 1785 S.F ROTOR GE L449T VOLTS 2300/4000 NEMA DESIGN -- TEST S.O. TYPICAL DATA 250 AMPS 56.3/32.4 CODE LETTER H TEST DATE --- P DUTY CONT ENCLOSURE TEFC STATOR RES.@ 25 C.416/1.25 3/60 AMB C/INSUL 40/F E/S - REL S.O. FRAME HP TYPE PHASE/HERTZ " ( ( $%" "&"' ##"!!! ##"!!" OHMS (BETWEEN LINES) Page 12 of 18 AMPERES SHOWN FOR CONNECTION, IF OTHER VOLTAGE CONNECTIONS ARE AVAILABLE, THE AMPERES WILL VARY INVERSELY WITH THE RATED VOLTAGE. DR. BY CK. BY APP. BY DATE Printed on 4/30/14 ragsun A-C MOTOR PERFORMANCE CURVES ISSUE DATE

13 F DUTY MASTER ALTERNATING CURRENT MOTORS SQUIRREL-CAGE INDUCTION F ENCLOSURE: TOTALLY ENCLOSED FRAME GL449T ABOVE NEMA RATINGS COOLING: FAN COOLED MOUNTING: FOOT INCLUDES DOWEL PIN HOLES, VERTICAL JACK SCREW HOLES, F1 AUX BOXES FOR WDG RTD & SPACE HEATERS AND 14X14X12 FABRICATED MAIN CBOX E E D SQ. KEY LEAD OPENING D C WDG RTDS (1)" NPT SPACE HTR (3/4)" NPT B 4X.38 THRU DOWEL HOLES XG= /2-13NC JACK SCREWS (4) TOTAL, 1 PER FOOT WEIGHT (LBS): HOLES 1/2-13 TAP THRU JACK SCREW HOLES YG= /16 6 HOLES GROUND HOLES QTY 1 1/2-13 TAP; QTY 1 3/8-16 TAP VARIES +.00,-.06 VARIES +.000,-.001 MOTOR WEIGHTS MAY VARY BY 15% DEPENDING ON RATING. OBSTRUCTION MUST NOT ENCROACH ON AIR INLET CONDUIT BOX LOCATED ON OPPOSITE SIDE WHEN F-2. IF MOUNTING CLEARANCE DETAILS ARE REQUIRED, CONSULT FACTORY. MAXIMUM PERMISSIBLE SHAFT RUNOUT WHEN MEASURED AT END OF STANDARD SHAFT EXTENSION IS.003" T.I.R. TO 5 INCH DIA. C B A DIMENSIONS ARE IN INCHES A CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT MOTOR PERFORMANCE IS SUITABLE IN THE APPLICATION. REV. DESC: ADD COG TO DRAWING REV: A VERSION: 01 REVISED: 01:40:05 08/31/2015 TDR: MODEL NO BY: RAGJSS1 4 Material: 3 REF: C D/S GL449T W/ 14X14X12 CB,DOWEL,JACK SCREWS,320 AUX,180 AUX 2 1 Page 13 of 18

14 F DUTY MASTER ALTERNATING CURRENT MOTORS SQUIRREL-CAGE INDUCTION F ENCLOSURE: TOTALLY ENCLOSED FRAME GL449T ABOVE NEMA RATINGS COOLING: FAN COOLED MOUNTING: FOOT INCLUDES DOWEL PIN HOLES, VERTICAL JACK SCREW HOLES, F1 AUX BOXES FOR WDG RTD & SPACE HEATERS AND 14X14X12 FABRICATED MAIN CBOX E E D SQ. KEY LEAD OPENING D C WDG RTDS (1)" NPT SPACE HTR (3/4)" NPT B 4X.38 THRU DOWEL HOLES XG= /2-13NC JACK SCREWS (4) TOTAL, 1 PER FOOT WEIGHT (N): HOLES 1/2-13 TAP THRU JACK SCREW HOLES YG= /16 6 HOLES GROUND HOLES QTY 1 1/2-13 TAP; QTY 1 3/8-16 TAP VARIES +.00,-1.5 VARIES +.000,-.025 MOTOR WEIGHTS MAY VARY BY 15% DEPENDING ON RATING. OBSTRUCTION MUST NOT ENCROACH ON AIR INLET CONDUIT BOX LOCATED ON OPPOSITE SIDE WHEN F-2. IF MOUNTING CLEARANCE DETAILS ARE REQUIRED, CONSULT FACTORY. MAXIMUM PERMISSIBLE SHAFT RUNOUT WHEN MEASURED AT END OF STANDARD SHAFT EXTENSION IS.076MM T.I.R. TO 127MM DIA. C B A DIMENSIONS ARE IN MM, SEE SHEET 1 FOR DIMENSIONS IN INCHES A CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT MOTOR PERFORMANCE IS SUITABLE IN THE APPLICATION. REV. DESC: ADD COG TO DRAWING REV: A VERSION: 01 REVISED: 01:40:05 08/31/2015 TDR: MODEL NO BY: RAGJSS1 4 Material: 3 REF: C D/S GL449T W/ 14X14X12 CB,DOWEL,JACK SCREWS,320 AUX,180 AUX 2 1 Page 14 of 18

15 Page 15 of 18

16 Marketing maintained PDF of MN408: Page 16 of 18

17 Marketing maintained PDF of MN416: Page 17 of 18