Product Information Packet ECP4406T-4 150HP,1785RPM,3PH,60HZ,445T,A4488M,TEFC

Transcription

1 Product Information Packet ECP4406T-4 150HP,1785RPM,3PH,60HZ,445T,A4488M,TEFC Copyright All product information within this document is subject to ABB Motors and Mechanical Inc. copyright protection, unless otherwise noted.

2 Part Detail Revision: K Status: PRD/A Change #: Proprietary: No Type: AC Elec. Spec: A44WG3335 CD Diagram: Mfg Plant: Mech. Spec: Layout: Poles: 04 Created Date: Base: Eff. Date: Leads: 3#1/0 Y Specs Catalog Number: ECP4406T-4 Insulation Class: F Enclosure: TEFC Inverter Code: Inverter Ready Frame: 445T KVA Code: F Frame Material: Iron Lifting Lugs: Standard Lifting Lugs Frequency: HZ Motor Lead Quantity/Wire Size: 1/0 AWG Synchronous Frequency: HZ Motor Type: A4488M Frequency: HZ Mounting Arrangement: F1 XP Class and Group: None Power Factor: 86 XP Division: Division II Product Family: Other Agency Approvals: CSA EEV Pulley End Bearing Type: Ball Auxillary Box: No Auxillary Box Pulley Face Code: Standard Base Indicator: Rigid Shaft Ground Indicator: No Shaft Grounding Bearing Grease Type: Polyrex EM (-0F +300F) Shaft Rotation: Reversible Constant Torque Speed Range: Shaft Slinger Indicator: No Slinger Voltage: V Speed Code: Single Speed Design Code: B Motor Standards: NEMA Drip Cover: No Drip Cover Starting Method: Direct on line Duty Rating: CONT Thermal Device - Bearing: NONE (OLD) Page of 14

3 Feedback Device: NO FEEDBACK Thermal Device - Winding: None Heater Indicator: No Heater XP Temp Code: T3 Page 3 of 14

4 Nameplate NP338 CAT NO ECP4406T-4 SPEC NO. P44G3930 HP 150 AMPS 169 VOLTS 460 DESIGN B FRAME 445T RPM 1785 HZ 60 AMB 40 SF 1.15 D.E. BRG.DATA 6318 O.D.E. BRG.DATA 6318 PH 3 DUTY CONT INSUL.CLASS F D.E. BRG. 90BC03J30X TYPE P ENCL TEFC CODE F O.D.E. BRG. 90BC03J30X POWER FACTOR 86 NEMA NOM EFFICIENCY /4 LOAD EFF MAX CORR KVAR 30.0 GUARANTEED EFFICIENCY 95.0 TEMP CODE T3 TEMP = 00 CHP HZ CT HZ VT HZ 0-60 INVERTER-TEMP-CODE T3 SER.NO. MOTOR WEIGHT Page 4 of 14

5 Nameplate NP496L MOBIL POLYREX EM Page 5 of 14

6 Parts List Part Number Description Quantity SA49388 SA P44G EA RA3653 RA P44G EA LABEL, MYLAR EA PU N/P (RELEASE QTY 10,000) UL CSA LABEL EA VD LABEL WARNING EA NP338 SS CP XEX SEVERE DUTY MAIN NP EA A G8 BRKT WCA KB EA B CLAMP EA RA G8 SHORT FAN COVER W/BAFFLE ASSEMBLY EA DA KEY 1/4X1/4X1-3/4 L EA R FAN KB 34/150 (84) EA A GREASE POLYREX EM LB FK HHCS 3/4-10X-1/ PLTD EA CK HHCS 3/8-16X1L PLATED EA DK HHCS 1/-13X3-3/4 PLTD EA A CPLG 1/8 HEX TYPE EA A WSHR EA AB LCKW 3/8 STD. PLATED EA AB P/NIP 1/8 X 8" L Pipe Nipple EA A G8 BRKT WCA KB EA FK HHCS 3/4-10X-1/ PLTD EA DK HHCS 1/-13X3-3/4 PLTD EA C +CBCST BLKT EA A CBCST BLKT EA Page 6 of 14

7 Parts List (continued) Part Number Description Quantity G GASK, LAC FT C GASK EA DK HHCS 1/-13X1 PLATED EA D T/LUG #4AWG-1/0AWG W/HOLE FOR.50 BOLT EA A PLUG - FAN COVER EA LB HHTTS 1/4-0X3/4 PLTD EA MG105N19 WILKO BLUE GREEN - 55 GAL DRUMS 0.50 GA EA DRSCR #6-1/4 304 S.S..000 EA KA KEY 7/8X7/8X6-3/4 L EA AB PPLG 3/4 PLATED.000 EA LA SOCKET SET SCREW EA G RETAIN RING EA BK HHCS 5/16-18X1/ PLATED EA A CPLG 1/8 HEX TYPE EA BK HHCS 5/16-18X3/4 PLATED EA A THERMAL BARRIER -- G8 -- BRACKET MTD EA AB LCKW 5/16 STD. PLATED EA AB P/NIP 1/8X5-1/L GALV EA FF N/P EA AB BUSH 1/4 TO 1/8 PLTD EA BB P/NIP 1/4X8 PLATED EA A SLGR EA BB P/NIP 1/4X5-1/L PLT EA AB BUSH 1/4 TO 1/8 PLTD EA Page 7 of 14

8 A GASKET, EA BK HHCS 5/16-18X1L PLATED EA A GREASE FITTING CAP EA A ALFTG 1/8" 1610-BL EA A ALFTG 1/8" 1610-BL EA A GREASE FITTING CAP EA A SLGR EA PK5004A09 BASE 48 X 39-1/4 STACK X 4 RUUNER EA LB1449 DIV-/NEC WARNING LABEL EA A DRAIN.000 EA NP496L MOTOR LUBE NAMEPLATE EA G GREASE RELIEF FITTING, ALEMITE EA G GREASE RELIEF FITTING, ALEMITE EA Page 8 of 14

9 xt Product Information Packet: ECP4406T-4-150HP,1785RPM,3PH,60HZ,445T,A4488M,TEFC REL. S.O. AMPS E/S FRAME HP TYPE 445LP 150 P 3/ DUTY 169 CONT 40/F 1.15 B F TEFC ROTOR AMB C/ INSUL. S.F. TEST S.O PERFORMANCE LOAD HP AMPERES RPM NO LOAD 1/4 /4 3/4 4/4 5/4 LOCKED ROTOR PULL UP BREAKDOWN FULL LOAD PHASE/ HERTZ NEMA DESIGN TEST DATE SPEED TORQUE RPM TORQUE % FULL LOAD RPM CODE LETTER % POWER FACTOR TORQUE LB.-FT. VOLTS ENCL. STATOR RES.@5 C OHMS (BETWEEN LINES) % EFFICIENCY AMPERES Page 9 of 14 AMPERES SHOWN FOR 460. VOLT CONNECTION. IF OTHER VOLTAGE CONNECTIONS ARE AVAILABLE, THE AMPERES WILL VARY INVERSELY WITH THE RATED VOLTAGE REMARKS: TYPICAL DATA NEMA NOMINAL EFFICIENCY = 95.8 PCT. DR. BY CK. BY APP. BY DATE CD CD R. MCELVEEN A-C MOTOR PERFORMANCE DATA A44WG3335-R001 1/18/11 ISSUE DATE 03/14/18 Printed on 3/14/18 bengap01.ba

10 xt Product Information Packet: ECP4406T-4-150HP,1785RPM,3PH,60HZ,445T,A4488M,TEFC RPM 1785 S.F ROTOR 0 445LP VOLTS 460 NEMA DESIGN B TEST S.O. TYPICAL DATA 150 AMPS 169 CODE LETTER F TEST DATE --- P DUTY CONT ENCLOSURE TEFC STATOR RES.@ 5 C.098 3/60 AMB C/INSUL 40/F E/S 0 REL S.O. FRAME HP TYPE PHASE/HERTZ SPEED IN RPM (4) TORQUE IN LB. FT. () P.F.() & EFF.(3) IN % AMPS AT 460 VOLTS (1) AMPS AT 460 VOLTS (1) NEMA NOMINAL EFFICIENCY = 95.8 PCT SPEED IN RPM,(FLT = 44 LB. FT.) OHMS (BETWEEN LINES) HORSEPOWER FL Page 10 of 14 AMPERES SHOWN FOR 460 VOLT CONNECTION, IF OTHER VOLTAGE CONNECTIONS ARE AVAILABLE, THE AMPERES WILL VARY INVERSELY WITH THE RATED VOLTAGE. DR. BY CK. BY APP. BY DATE CD CD R. MCELVEEN 1/18/11 A-C MOTOR PERFORMANCE CURVES Printed on 3/14/18 bengap01.baldor.com A44WG3335-R001 03/14/18 ISSUE DATE

11 xt Product Information Packet: ECP4406T-4-150HP,1785RPM,3PH,60HZ,445T,A4488M,TEFC RPM 1785 S.F ROTOR 0 445LP VOLTS 460 NEMA DESIGN B TEST S.O. TYPICAL DATA 150 AMPS 169 CODE LETTER F TEST DATE --- P DUTY CONT ENCLOSURE TEFC STATOR RES.@ 5 C.098 3/60 AMB C/INSUL 40/F E/S 0 OHMS (BETWEEN LINES) REL. S.O. FRAME HP TYPE PHASE/HERTZ TIME IN SEC. MOTOR INITIAL TEMPERATURE: 13C FOR OVERLOAD AND ACC. OVERLOAD 13 C FOR LOCKED-ROTOR LOCKED-ROTOR, 40.C ACCELERATION LOCKED-ROTOR % FULL LOAD CURRENT Page 11 of 14 REMARKS: THERMAL LIMIT CURVE NEMA NOMINAL EFFICIENCY = 95.8 PCT. AMPERES SHOWN FOR 460 VOLT CONNECTION, IF OTHER VOLTAGE CONNECTIONS ARE AVAILABLE, THE AMPERES WILL VARY INVERSELY WITH THE RATED VOLTAGE. DR. BY CK. BY APP. BY DATE CD CD R. MCELVEEN 1/18/11 A-C MOTOR PERFORMANCE CURVES A44WG3335-R001 ISSUE DATE 03/14/18 Printed on 3/14/18 bengap01.ba

12 F DUTY MASTER ALTERNATING CURRENT MOTORS SQUIRREL-CAGE INDUCTION F ENCLOSURE: TOTALLY ENCLOSED FRAME G445T ABOVE NEMA RATINGS COOLING: FAN COOLED MOUNTING: FOOT INCLUDES 444T FRAME MOUNTING HOLES E E D 8.36 D SQ. KEY 4.4 C C LEAD OPENING /16 8 HOLES B B GROUND HOLES QTY 1 1/-13 TAP; QTY 1 3/8-16 TAP VARIES +.00,-.06 VARIES +.000,-.001 ON STANDARD MOTORS THIS IS CONDUIT SIZE. ON XT AND CORROSION PROOF MOTOR THIS IS PIPE TAP. MOTOR WEIGHTS MAY VARY BY 15% DEPENDING ON RATING. OBSTRUCTION MUST NOT ENCROACH ON AIR INLET 5 WEIGHT (LBS): 130 DRIVE END AIR DEFLECTOR IS ONLY INCLUDED WHEN NECESSARY. A SHEET NUMBER 1 OF CONDUIT BOX LOCATED ON OPPOSITE SIDE WHEN F-. IF MOUNTING CLEARANCE DETAILS ARE REQUIRED, CONSULT FACTORY. MAXIMUM PERMISSIBLE SHAFT RUNOUT WHEN MEASURED AT END OF STANDARD SHAFT EXTENSION IS.003" T.I.R. TO 5 INCH DIA DIMENSIONS ARE IN INCHES; SEE SHEET FOR DIMENSIONS IN MILLIMETERS CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT MOTOR PERFORMANCE IS SUITABLE IN THE APPLICATION. REV. DESC: SHEET NEEDS METRIC FOOT HOLE DIMENSION REV: E VERSION: 05 REVISED: 09::56 06/1/014 TDR: MODEL NO REF: G445T/444T STD FOOTED SIDE/CENTER C/B BY: RAGRA Material: C A Page 1 of 14

13 F DUTY MASTER ALTERNATING CURRENT MOTORS SQUIRREL-CAGE INDUCTION F ENCLOSURE: TOTALLY ENCLOSED FRAME G445T ABOVE NEMA RATINGS COOLING: FAN COOLED MOUNTING: FOOT INCLUDES 444T FRAME MOUNTING HOLES E E D 1.3 D SQ. KEY C C LEAD OPENING HOLES B B GROUND HOLES QTY 1 1/-13 TAP; QTY 1 3/8-16 TAP VARIES +.0,-1.5 VARIES +.00,-.03 ON STANDARD MOTORS THIS IS CONDUIT SIZE. ON XT AND CORROSION PROOF MOTOR THIS IS PIPE TAP. MOTOR WEIGHTS MAY VARY BY 15% DEPENDING ON RATING. OBSTRUCTION MUST NOT ENCROACH ON AIR INLET 5 WEIGHT (KGS): 970 DRIVE END AIR DEFLECTOR IS ONLY INCLUDED WHEN NECESSARY. A SHEET NUMBER OF CONDUIT BOX LOCATED ON OPPOSITE SIDE WHEN F-. IF MOUNTING CLEARANCE DETAILS ARE REQUIRED, CONSULT FACTORY. MAXIMUM PERMISSIBLE SHAFT RUNOUT WHEN MEASURED AT END OF STANDARD SHAFT EXTENSION IS.08 MM T.I.R. TO 17 MM DIA DIMENSIONS ARE IN MILLIMETERS; SEE SHEET 1 FOR DIMENSIONS IN INCHES CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT MOTOR PERFORMANCE IS SUITABLE IN THE APPLICATION. REV. DESC: SHEET NEEDS METRIC FOOT HOLE DIMENSION REV: E VERSION: 05 REVISED: 09::56 06/1/014 TDR: MODEL NO REF: G445T/444T STD FOOTED SIDE/CENTER C/B BY: RAGRA Material: C A Page 13 of 14

14 Page 14 of 14