***Before starting : view the Virtual tour located at c:/programs/msoffice/powerpointviewer And carry out the tutorials in the manuals supplied***
|
|
- Susan McDaniel
- 5 years ago
- Views:
Transcription
1 Fatigue Machine Turn on Chiller isolator to machine (Located behind Torque/ Tension Machine) Turn on main isolator to machine Reset Isolator switch and wait for all LEDs to go from red to off LED s Starter Overload - Motor Overload very rare Pressure Line Filter - Filter on top of Reservoir Return Line Filter - Filter on RHS of Reservoir Oil Temperature - Thermocouple in Reservoir attached to water valve Oil Level - Sensor in Reservoir Turn on PC power Supply and monitor ***Before starting : view the Virtual tour located at c:/programs/msoffice/powerpointviewer And carry out the tutorials in the manuals supplied*** Open Virtual Control Panel Reset control panel and check LEDs all green ***Before starting Pump and oil pressure set up machine parameters*** Main Menu 1 Input Zero - If want the stroke zero datum to be offset (default AUTO datum set to current position) Working Range - each Stroke = max +/- 50 mm Strain = extensometer only colour coded for Load = Load Cell 100 KN capacity. OPERATING INSTRUCTION FATIGUE MACHINE Page 1 of 7 10/09/2002 Chris Crouch
2 Proportional Gain - Difference set value to measured value (Auto Gain Control) Servo Integrator - errors) Set to ON (applies bias current which reduces servo null Servo Dither - Set to ON (signal 500Hz fed to servo valve to reduce static friction) Cycle Counter - Set number of cycles to run and stop test Input Limits Menu 2 Input Limits should all be OFF Upper and Lower Input Limits - set to Default (max working range) Function Generator Menu 3 Ramp Generator Compressive (-) Tensile (+) Mode - Soft keys bottom of screen (Stroke/Strain/Load) Rate - 5 KN/sec Load 1 mm/sec Stroke (select /h,/min) Hold Level - Value required Hold Time - When Off when ramp reaches the hold level it stops When On Ramp reaches hold level it Holds for time limit set and then starts Ramp2 Generator. (maybe cyclic) Status - Off Highlight and turn ON to start Ramp Generator Oscillator Waveform - Sine (pull down menu of various types) OPERATING INSTRUCTION FATIGUE MACHINE Page 2 of 7 10/09/2002 Chris Crouch
3 Mode - Highlight to select softkey choice (Stroke/ Strain/ Load) Amplitude - Type in Value (max deviation from starting point ) Highlighted mode allows softkey Adaptive On (More accurate amplitude limit values at machine limits) Frequency - Osc freq set from 1mHz to Hz Status - Off Highlight and turn ON to start Oscillator cycle Soft Start - 2 sec Prevents shock loads by allowing time set to reach amplitude level and to decay to zero. (0-2 sec) Inner Limit Menu 4 Inner Limits should all be OFF Calibration Menu 5 Use default values Baud Rate bps Bias - 0 Servo Drive limit % Test code - 0 VCP window File - Open controller settings (default machine settings 0 4 ) factory default settings DCU settings Pull down Hydraulic menu Push Reset Button Turn ON - PUMP A (wait for LED to go green and Pressure button to activate) Turn On - PRESSURE OK window OPERATING INSTRUCTION FATIGUE MACHINE Page 3 of 7 10/09/2002 Chris Crouch
4 Turn ON Crosshead control using key on front panel LED red Move crosshead up or down Control speed by opening or closing star tap Move Piston to ZERO position using scroll bar Add specimen to top jaws Move crosshead down to locate inside bottom jaws Close speed control tap Clockwise Turn key off Typical starting values Ramp Generator Ramp 1 Stroke Ramp 2 Load 1 mm/ sec 5 KN/ sec 10 mm 10 KN 0 time (OFF if Ramp1only) OFF Status ON OFF Oscillator Waveform Sine Mode ; Stroke Amplitude 5 mm Frequency 1 Hz Status ON To produce graphs and save data use Macro function and / or Block editor Block Editor Block 1 Wait (append) Block 2 Stroke hold for 5 sec no status on block Block 3 Load -20 KN (compression) 1 KN/s yes acquire data OPERATING INSTRUCTION FATIGUE MACHINE Page 4 of 7 10/09/2002 Chris Crouch
5 Block 4 L 0 KN 2 KN/s No graph/ data acquire Block 5 stroke hold 1 sec No data /graph Enter password Capital ESH save block as XXXX To run Block Program Set up machine settings Stroke 5 mm Load 20 KN Retrieve Block Program XXXX Save to result file XXXX Specimen dia 40 mm with M10 thread at ends Sq XX mm width and depth Run test T/ on pump & pressure Raise/ lower crosshead Fit specimen Start test Results saved into data files (binary bits) and need to convert to ASCII by running Playback program in Macro files To View Data Open ASCII file by using exporter software Click on Exporter Icon Choose file to export XXXX.dat Choose destination : C:/Programfiles/ MicrosoftOffice/Office /Excel.exe Save file XXXX.xls OPERATING INSTRUCTION FATIGUE MACHINE Page 5 of 7 10/09/2002 Chris Crouch
6 Fatigue Machine Name plate has Machine specification on Pressure and Filters Machine Number Working Pressure bar (Push in knob to read current Pressure) Hydraulic Flow Rate - 23 L / min Pressure Filter - R63013 Return Flow Filter - R6121 Oil Capacity Litres Oil Type - Shell Tellus 37 (Grade 37) Pressure Gauge on Reservoir set to 9.25 Water Valve set to 2.25 Reservoir piping Draw (return overflow) Pressure Return Frame built for 250 KN Load Cell supplied) Piston only rated for 100 KN (Load Cell and clamping ring Load Cell attached to Machine 29/03/01 hours of running = 1,000 Should Change Oil after 5 years hours or when oil dirty. flat jaws 0-6 mm 6-12 mm Round jaws in toolbox Tensile sprung jaws - tighten and release specimen undo allen head screws M12 2 screws open and close jaws if become stuck OPERATING INSTRUCTION FATIGUE MACHINE Page 6 of 7 10/09/2002 Chris Crouch
7 Compression test Adaptors to clamp vacuum furnace to head and cylinder also for compression testing large jaw at top Need washers/ slave spacers Tighten lock washer on jaws so there is 1/2 a turn to tighten Slave disc on jaws top and bottom Vacuum Furnace Tensile test 800C under vac Extensometer Add clip to strain gauge before fitting Add clip and gauge to specimen Ceramic extensometer for furnace colour coded cabling LVDT extensometer for furnace colour coded cabling Data acquisition card has a maximum of 10,000 cycles only This is maximum program capacity due to design limits of downloading data to hard drive. OPERATING INSTRUCTION FATIGUE MACHINE Page 7 of 7 10/09/2002 Chris Crouch
SHOCK ABSORBER/DAMPER TESTING MACHINE
SHOCK ABSORBER/DAMPER TESTING MACHINE Dampening force of a shock absorber is directly proportional to velocity and this parameter needs to be precisely controlled. A small variation of 1mm in a stroke
More informationIntroduction. Figure 1: Labeled picture of the Instron 3367 load frame.
Operation of the Instron Tensile Test Machine With an Existing Method in Bluehill 3 Software Introduction by Andrew E. Frerichs, 3/25/11 Michelle Grawe; 10/6/14 Introduction The Instron device is a displacement
More informationMTS Criterion Series 40 Specifications - Comparative
MTS Criterion Series 40 Specifications - Comparative Model 41 Model 42 Model 43 Model 44 C41.103 C42.503 C43.104 C43.304 C43.504 C44.104 C44.304 Maximum Rated kn 1 5 10 30 50 10 30 Force Capacity lbf 220
More informationSetting Up an Oscillation Amplitude Sweep Test
Setting Up an Oscillation Amplitude Sweep Test 6. Select an Oscillation Amplitude test. 8. Enter the Soak time to allow for temperature equilibration. ( A ten-minute soak time is 9. Enter the Frequency
More informationKEMKRAFT ENGINEERING, INC. MODEL KEI-234 STEERING WHEEL TORQUE/INCLINOMETER TESTER
INSTRUCTION MANUAL STEERING WHEEL TORQUE/ INCLINOMETER SYSTEM MODEL KEI-234 W / INTERNAL BARCODE SCANNER REVISION DATE: 17-AUG-1999 1 GENERAL DESCRIPTION... 3 INSTALLATION... 3 SYSTEM SETUP... 4 To change
More informationAn Introduction to Fatigue Testing Equipment, Test Setup & Data Collection
An Introduction to Fatigue Testing Equipment, Test Setup & Data Collection Lisa Goodwin Servohydraulic Sales Specialist & Market Manager - Instron The difference is measurable 1 Themes.. Certainty of Measurement
More informationHYDRAULIC & ENGINEERING INSTRUMENTS. Servo Hydraulic Universal Fatigue Testing System
HYDRAULIC & ENGINEERING INSTRUMENTS Servo Hydraulic Universal Fatigue Testing System Servo Hydraulic Universal Fatigue Testing System (Capacity-Ranges from kn-0kn) HI Series of Servo Hydraulic Universal
More informationHS CYCLIC CUM STATIC TRIAXIAL TEST SYSTEM
HS28.610 CYCLIC CUM STATIC TRIAXIAL TEST SYSTEM Meets the essential requirements of ASTM-5311/3999 Introduction The system is a highly advanced combination of hydraulic and pneumatic technology where σ1
More informationServohydraulic Testing Machines for Dynamic Testing UFIB Series
Servohydraulic Testing Machines for Dynamic Testing UFIB Series Capacity: 10-250 kn or more S.a.e. ibertest Made in Europe (Spain) Fabricantes desde 1970 Universal Servo hydraulic Dynamic Testing Machines,.
More informationAdvanced Force / Torque Indicator
32-1128 Advanced Force / Torque Indicator The 5i advanced digital force / torque indicator is designed to work with a wide range of Mark-10 remote force and torque sensors (see page 3). With exclusive
More informationVacuum Pump ( /-03) SP3. Owner s Manual
Vacuum Pump (01840-02/-03) SP3 Owner s Manual Congratulations on your choice of purchasing the SP3 Vacuum Pump! The new SP3 Vacuum Pump lets you to charge and discharge most of the shock absorbers, steering
More informationCompression/Tension Testing Machines
Manual Cement Compression and Flexure Testing Machines UTCM-6310/UTCM-6410 The UTCM-6310 and UTCM-6410 single and double testing chamber Manual compression and flexure testing machines are designed to
More informationOperating Instructions for Instron Model 4400 Series Load Frames
OperatingInstructionsforInstronModel4400 Series LoadFrames John D. Williams and David E. Farrow SAFETY FIRST TheInstron 4400loadframegenerateshighforces.Thecapacityoftheframeis100kN(thatis, 22.5kipsor11.3tons).Theframedoesnotknowthedifferencebetweenasteelplateandyourhand.
More informationServo and Proportional Valves
Servo and Proportional Valves Servo and proportional valves are used to precisely control the position or speed of an actuator. The valves are different internally but perform the same function. A servo
More informationData Sheet. Motorized Test Stand w/pc Control ESM303
Page 1 of 5 The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbf [1.5 kn], with a rugged design suitable for laboratory and
More informationLoadcell Tension Control
CORTEX INDUSTRIAL SYSTEM CONTROLLER Loadcell Tension Control Instruction Manual Model CORTEX-D00 Table of Contents 1. General Description... 2 2. Specifications... 3 2.1 Electrical... 3 2.2 Physical...
More informationMitsubishi. VFD Manuals
Mitsubishi VFD Manuals Mitsubishi D700 VFD Installation Mitsubishi FR-D700 VFD User Manual Mitsubishi D700 Parallel Braking Resistors VFD Wiring Diagram - Apollo Mitsubishi VFD to Interpreter Mitsubishi
More informationData Sheet. Motorized Test Stand w/pc Control ESM303H. Standard Features. Page 1 of 5
Page 1 of 5 The ESM303H is a highly configurable horizontal force tester for tension and compression measurement applications up to 300 lbf [1.5 kn], with a rugged design suitable for laboratory and production
More informationServo-hydraulic Universal Testing Machine HUT Type DP
Test type Slip & Tensile Strength Permanent Elongation & Tensile Strength Static Tension Test Static Compression Test Cyclic Tension & Compression Test Test standards AC 133: 2010: 4.1 BS 8110: PART 1:
More informationTORQUE CALIBRATION USING THE PROEDIT PROCEDURE WIZARD AND CALIBRATING USING PROCAL
TORQUE CALIBRATION USING THE PROEDIT PROCEDURE WIZARD AND CALIBRATING USING PROCAL - Overview Torque Calibration The Transmille 3000A Series torque calibration option uses the EA014 Torque adapter, a transducer
More informationSP4 DOCUMENTATION. 1. SP4 Reference manual SP4 console.
SP4 DOCUMENTATION 1. SP4 Reference manual.... 1 1.1. SP4 console... 1 1.2 Configuration... 3 1.3 SP4 I/O module.... 6 2. Dynamometer Installation... 7 2.1. Installation parts.... 8 2.2. Connectors and
More informationSeries 1780 Dynamometer V2 Datasheet
Series 1780 Dynamometer V2 Datasheet Typical use Outrunner brushless motor characterization 25 kgf / 0-100 A 40 kgf / 0-150 A (Plus) Propeller characterization up to 47 Servo testing and control Battery
More informationVFD - Mitsubishi. VFD Manuals. Mitsubishi D700 VFD Installation. Mitsubishi FR-D700 VFD User Manual. Mitsubishi D700 Parallel Braking Resistors
VFD - Mitsubishi VFD Manuals Mitsubishi D700 VFD Installation Mitsubishi FR-D700 VFD User Manual Mitsubishi D700 Parallel Braking Resistors VFD Wiring Diagram - Apollo Mitsubishi VFD to Interpreter Mitsubishi
More informationCONTROL UNIT OMEGA 800-R. User manual
CONTROL UNIT OMEGA 800-R User manual INDEX 1. DESCRIPTION AND MAIN FEATURES... 3 2. DISPLAY AND CONTROL BUTTONS... 4 3. INSTALLATION AND CONNECTIONS... 5 4. MENU STRUCTURE... 6 5. HOW TO CHECK OR MODIFY
More informationHydraulic Proportional and Closed Loop System Design
Hydraulic Proportional and Closed Loop System Design Neal Hanson Product Manager Industrial Valves and Electrohydraulics 1 Electrohydraulics Contents 1. Electrohydraulic Principles 2. Proportional Valve
More informationTECHNICAL PRODUCT DATASHEET
FORM-ENG-0018 REV A 06-02-03 ISO 9001 CERTIFIED Phone: (352) 629-5020 or 800-533-3569 Fax: (352)-629-2902 SUITABLE FOR EXTERNAL DISTRIBUTION TECHNICAL PRODUCT DATASHEET Sentry Pressure Governor P/N 3045-101-00-CL1
More informationESM1500 / ESM750. Data Sheet. Motorized Force Test Stands. Standard Features. Page 1 of 6
Page 1 of 6 ESM1500 1,500 lbf [6.7 kn] 32 in [813 mm] travel ESM1500S 1,500 lbf [6.7 kn] 14.2 in [360 mm] travel ESM750S 750 lbf [3.4 kn] 14.2 in [360 mm] travel ESM1500 and ESM750 singlecolumn force testers
More informationSERVO-HYDRAULIC UNIVERSAL TESTING MACHINE SERIES D
SERVO-HYDRAULIC UNIVERSAL TESTING MACHINE SERIES D STANDARD BS 8110: PART 1: 1997 3.12.8.16.2, BS4482. BS4483, BS4449, ASTM A 1034: 10.5, 10.7 TEST TYPE Slip & Tensile Strength Permanent Elongation & Tensile
More informationESM1500 / ESM750. Data Sheet. Motorized Force Test Stands. Standard Features. Page 1 of 6
Page 1 of 6 ESM1500S 1,500 lbf [6.7 kn] 14.2 in [360 mm] travel ESM1500 1,500 lbf [6.7 kn] 32 in [813 mm] travel ESM750 750 lbf [3.4 kn] 32 in [813 mm] travel ESM750S 750 lbf [3.4 kn] 14.2 in [360 mm]
More informationTE 91 PRECISION ROTARY VACUUM TRIBOMETER
TE 91 PRECISION ROTARY VACUUM TRIBOMETER Description The TE 91 Precision Rotary Vacuum Tribometer is based on a bench mounted test chamber. A motor driven test spindle, in the form of standard rotary feedthrough,
More informationBAYLAN AUTOMATED TEST BENCH
BAYLAN AUTOMATED TEST BENCH At this test bench, the electromagnetic flow meters are used with the measurement method. Calibrations of flowmeters are made with the help of the water collection tank and
More informationÖhlins Vacuum Oil Filling Machine ( /-05)
Öhlins Vacuum Oil Filling Machine (01840-04/-05) Owner s Manual TO DO BEFORE FIRST START ATTENTION TO GET THE BEST PERFORMANCE FROM THE PUMP, THE FILTER WILL BE ENCLOSED SEPARATELY DURING TRANSPORT. BEFORE
More informationObserve all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning.
Introduction OPERATING INSTRUCTIONS: MCD REMOTE OPERATOR Order Codes: 175G94 (for MCD 2) 175G361 + 175G9 (for MCD 5) 175G361 (for MCD 3) 1. Introduction 1.1. Important User Information Observe all necessary
More informationOMEM200 Tuning Manual 3v Series ECU. Tuning Manual OMEM200.
200 Series ECU Tuning Manual OMEM200 www.omextechnology.com 0 1 Introduction... 3 1.1 What this manual covers... 3 1.2 Notation Used in This Manual... 3 2 Software... 4 3 Sensor Setup... 5 3.1 Throttle
More informationFLEC AIR PUMP Operators Manual JULY QUI-1030 VERSION 1.2
FLEC AIR PUMP 1001 Operators Manual JULY 2009 QUI-1030 VERSION 1.2 This page left intentionally blank FLEC AIR PUMP 1001 Operators Manual Contents 1. Introduction 4 2. Operating instructions 5 2.1. Operating
More informationGloboFleet. User manual. GloboFleet Downloadkey EAN / GTIN
GloboFleet GloboFleet Downloadkey User manual EAN / GTIN 4260179020070 Content Content / Overview...2 Read out tachograph data...3 Read out tachograph data and driver card...4 Transfer data to a computer...5
More informationAutomatic Genset Controller, AGC-4 Display readings Push-button functions Alarm handling Log list
OPERATOR'S MANUAL Automatic Genset Controller, AGC-4 Display readings Push-button functions handling Log list DEIF A/S Frisenborgvej 33 DK-7800 Skive Tel.: +45 9614 9614 Fax: +45 9614 9615 info@deif.com
More informationIssue 2.0 December EPAS Midi User Manual EPAS35
Issue 2.0 December 2017 EPAS Midi EPAS35 CONTENTS 1 Introduction 4 1.1 What is EPAS Desktop Pro? 4 1.2 About This Manual 4 1.3 Typographical Conventions 5 1.4 Getting Technical Support 5 2 Getting Started
More informationBRAKE TESTER DECELEROMETER
OC3010_GBM_21009 BRAKE TESTER DECELEROMETER OWNER S MANUAL Version 8.++ ORBIT CONTROLS AG Zürcherstrasse 137 CH-8952 Schlieren/ZH Tel: + 41 44 730 2753 Fax: + 41 44 730 2783 info@orbitcontrols.ch www.orbitcontrols.ch
More informationServo-hydraulic Universal Testing Machine HUT Type D
Test type Slip & Tensile Strength Permanent Elongation & Tensile Strength Static Tension Test Static Compression Test Test standards BS 8110: PART 1: 1997 3.12.8.16.2 BS4482 BS4483 BS4449 ASTM A 1034:
More informationTE 88 MULTI-STATION FRICTION & WEAR TEST MACHINE
TE 88 MULTI-STATION FRICTION & WEAR TEST MACHINE Background The TE 88 Multi-Station Friction and Wear Test Machine is design for wear testing of materials under high contact pressures in pin on disc, block
More informationConcrete ASTM COMPRESSION TESTER ACCESSORIES
ADR Advanced Digital Readout Menu-driven with simple data entry. Dual input and operating modes. Peak hold and auto stress calculation. RS232C output. Pace deviation bar graph for accurate load rate applications.
More informationT100 Vector Impedance Analyzer. timestechnology.com.hk. User Manual Ver. 1.1
T100 Vector Impedance Analyzer timestechnology.com.hk User Manual Ver. 1.1 T100 is a state of the art portable Vector Impedance Analyzer. This powerful yet handy instrument is specifically designed for
More informationBERMAD Waterworks. Insertion Flow Meter Device (IFM)
IFM-MUT1222PRV BERMAD's IFM-MUT1222-PRV SENSOR is designed for measuring the flow rate of valves sized DN80 to DN600 (3-24 ). This document describes the installation process of the sensor. For larger
More informationADHESION/RELEASE TESTER
ADHESION/RELEASE TESTER MODEL AR-2000 OPERATING INSTRUCTIONS CHEMINSTRUMENTS 510 COMMERCIAL DRIVE FAIRFIELD, OHIO 45014 (513) 860-1598 www.cheminstruments.com Revision 1.0 December 13, 2016 CONTENTS PRODUCT
More informationInstalling a Programmed Fronius SCERT in a Managed AC Coupled system
Installing a Programmed Fronius SCERT in INTRODUCTION This document is included with Fronius SCERT PV Inverters that have been programmed. It applies only to units that have been programmed and are ready
More informationLiquid, semi-liquid, dry, humidified, pressurized test chamber
The Falex MultiSpecimen Test Machine The Falex MultiSpecimen Test Machine is the most versatile commercial system for evaluating friction, wear, and abrasion characteristics of materials, coatings, and
More informationUniversal Testing Machine
Universal Testing Machine Model NRI-TS500-50 Please read this carefully before use. Keep it in the reference manual Page 1 20/12/2010 Table Contents Matter. Page Use of 3 To SUPERVISOR in charge of this
More informationSP5 INSTALLATION AND SETUP MANUAL
SP5 INSTALLATION AND SETUP MANUAL 1 Installation 1.1 Introduction The SP5 System consists of a Data Acquisition unit (DAQ) with two complete Roller control channels, each Roller Control Channel consists
More informationGENERAL MOTORS SERVICE PARTS OPERATION 6200 Grand Pointe Drive, Grand Blanc, MI 48439
LS IGNITION CONTROLLER 19355418 Ignition Control for Carbureted LS Series Engines (24x Crankshaft Index/1x Camshaft Index, 58x Crankshaft Index/4x Camshaft Index) Parts Included Quantity Ignition Controller
More informationSP PRO KACO Managed AC Coupling
SP PRO KACO Managed AC Coupling Introduction The SP PRO KACO Managed AC Coupling provides a method of linking the KACO Powador xx00 and Powador xx02 series grid tie inverters to the SP PRO via the AC Load
More informationAUTOMATIC TERMINAL CRIMPING MACHINE CPR-ZERO INSTRUCTION MANUAL
AUTOMATIC TERMINAL CRIMPING MACHINE CPR-ZERO INSTRUCTION MANUAL TABLE OF CONTENTS INTRODUCTION 1 STANDARD OPERATION MANUAL 61 KEEP SAFETY IN MAIND 2 Preparation for operation SPECIFICATUONS Supply wire
More informationCement Compression & Flexural Testing Machines
The Compression & Flexural testing product line from Torontech offers a wide variety that will fit almost any budget. Different options between models include digital or analog display, single or dual
More informationVERTEX UNIVERSAL TESTING MACHINE
OVERVIEW : Loading Accuracy as high as + 1% Straining at variable speeds to suit a wide range of materials. Continuous roll autographic recorder supplied as standard to enable study of the behavior of
More informationa measurable difference...
This testing machine with integrated steel plate welded frame structure, using single boom and double-function piston liner to load testing force and fixing specimen with cylindrical pin, load cell measuring
More informationWarning! Before continuing further, please ensure that you have NOT mounted the propellers on the MultiRotor.
Mission Planner Setup ( optional, do not use if you have already completed the Dashboard set-up ) Warning! Before continuing further, please ensure that you have NOT mounted the propellers on the MultiRotor.
More informationVT-HACD-DPQ Digital Controller for electro-hydraulic Injection Molding Machines
VT-HACD-DPQ Digital Controller for electro-hydraulic Injection Molding Machines Start-up DeviceNet Interface RE 30146-03-Z/08.07 2/120 Bosch Rexroth AG Hydraulics Start-up DeviceNet Interface RE 30146-03-Z/08.07
More informationCOMPASS MODULE INSTALLATION & OPERATION MANUAL RMI ROCKY MOUNTAIN INSTRUMENT PO BOX 683 THERMOPOLIS, WY 82443
COMPASS MODULE INSTALLATION & OPERATION MANUAL RMI ROCKY MOUNTAIN INSTRUMENT PO BOX 683 THERMOPOLIS, WY 82443 Table of Contents Technical Specifications Physical... 1 Electrical... 1 Mechanical... 1 Installation
More informationDevice Description User Manual Logix MD+ Positioners with HART
Device Description User Manual Logix MD+ Positioners with HART CONTENTS DD MENU CHART... 3 GENERAL INFORMATION... 6 INTRODUCTION... 6 QUALIFIED PERSONNEL... 6 USING THIS DOCUMENT... 6 TERMS CONCERNING
More informationload frames Juni 2002 Damper Testing INOVA-GMBH JS Folie Nr. 2
Damper Testing Juni 2002 Damper Testing INOVA-GMBH JS Folie Nr. 1 load frames Inova has a wide range of standard load frames from 10 kn up to 2 MN. This Standard load frames will be modified to meet the
More informationINDEX 1 Introduction 2- Software installation 3 Open the program 4 General - F2 5 Configuration - F3 6 - Calibration - F5 7 Model - F6 8 - Map - F7
SET UP MANUAL INDEX 1 Introduction 1.1 Features of the Software 2- Software installation 3 Open the program 3.1 Language 3.2 Connection 4 General - F2 4.1 The sub-folder Error visualization 5 Configuration
More informationPowerJet Sequential Injection INDEX. 1 Introduction 1.1 Features of the Software. 2- Software installation
INDEX 1 Introduction 1.1 Features of the Software 2- Software installation 3 Open the program 3.1 Language 3.2 Connection 4 Folder General - F2. 4.1 The sub-folder Error visualization 5 Folder Configuration
More informationGENERAL INFORMATION. H-1649, H-1650, H-1651 H-1653, H-1654 Easy-Count. uline.com. that may hurt accuracy:
π H-1649, H-1650, H-1651 H-1653, H-1654 Easy-Count counting scale 1-800-295-5510 uline.com 1-800-295-5510 GENERAL INFORMATION Avoid placing the scale in locations that may hurt accuracy: 1. Temperature
More informationOnline Capacity Tester MK70 User and PC-Software Manual
Online Capacity Tester MK70 User and PC-Software Manual User manual Online-Battery-Tester - 2 User manual Online-Battery-Tester - 3 Introduction: With this processor controlled capacity tester you can
More information1. An inverter can be programmed to stop an AC motor quickly by enabling
Student ID: 53703105 Exam: 086053 - Controlling Industrial Motors When you have completed your exam and reviewed your answers, click Submit Exam. Answers will not be recorded until you hit Submit Exam.
More informationTECHNICAL DOCUMENT EPC HORSEPOWER LIMITING
ELECTRONIC 1 A pump is a volume output device only. It delivers oil flow directly related in polarity and amplitude to the command voltage input to the pump amplifier (). Pressure at the pump output is
More informationZwick. Materials testing. Product Information LTM 5/10 electro-dynamic testing machine
CTA: 113389 113384 testing machine Range of application The LTM is an electro-dynamic testing machine with a drive based on linear motor technology. 's new, patented drive concept enables the LTM to be
More information(If this step is missed, then OBD software is not going to work. So it's CRUCIAL that you follow below steps).
How to Install ELM327 USB/Bluetooth on Mac and OBD Software Posted by Alex (Im) E. on 28 January 2013 02:53 AM This article will guide you on how to install ELM327 USB Cable / Bluetooth scanner on your
More informationVFD. Variable Frequency Drive
VFD Variable Frequency Drive Mitsubishi Mitsubishi D700 VFD Installation Mitsubishi FR-D700 VFD User Manual Mitsubishi D700 Parallel Braking Resistors VFD Wiring Diagram - Apollo Mitsubishi VFD to Interpreter
More informationSmart Load Cell TRQ1/TPL torque / top load tester family
SMARTLOADCELL USER S MANUAL Smart Load Cell TRQ1/TPL torque / top load tester family Serial numbers: TRQ1 torque tester: ST-E TPL-.. Top Load tester: ST-E Date of purchase:... Warranty: 3 years SLC-TRQ/TPL
More informationAutomated Seat Belt Switch Defect Detector
pp. 10-16 Krishi Sanskriti Publications http://www.krishisanskriti.org/publication.html Automated Seat Belt Switch Defect Detector Department of Electrical and Computer Engineering, Sri Lanka Institute
More informationInstron Model 4400 Series Load Frames
OPERATING INSTRUCTIONS Instron Model 4400 Series Load Frames THE COMPRESSION TEST Introduction Read General Operating Instructions to familiarize yourself with the Instron 4400. SAFETY FIRST Safety glasses
More informationOPERATING INSTRUCTIONS AutoForce
OPERATING INSTRUCTIONS AutoForce TRANSLATION OF THE ORIGINAL OPERATING INSTRUCTIONS READ CAREFULLY PRIOR TO STARTING UP! KEEP OPERATING INSTRUCTIONS IN A SAFE PLACE! ART.: ISSUE: 8072 0213 02/2017 - Translation
More informationMARELLI SRA EDL8 ECU
MARELLI SRA EDL8 ECU INTRODUCTION AIM has developed special applications for many of the most popular ECUs; by special applications we mean user-friendly systems which allow to easily connect your ECU
More informationPOWER SUPPLY MODEL XP-800. TWO AC VARIABLE VOLTAGES; 0-120V and 7A, PLUS UP TO 10A. Instruction Manual. Elenco Electronics, Inc.
POWER SUPPLY MODEL XP-800 TWO AC VARIABLE VOLTAGES; 0-120V and 0-40V @ 7A, PLUS 0-28VDC @ UP TO 10A Instruction Manual Elenco Electronics, Inc. Copyright 1991 Elenco Electronics, Inc. Revised 2002 REV-I
More informationW SERIES IMPULSE VOLTAGE TEST SYSTEM APPLICATION FEATURES
W SERIES IMPULSE VOLTAGE TEST SYSTEM Impulse Voltage Test System is used to generate impulse voltages from 100 KV to 2400 KV simulating lightning strokes and switching surges with energies up to 240 KJ.
More informationDENISON HYDRAULICS Jupiter 500 Driver Card Series S
Back to Content DENISON HYDRAULICS Jupiter 500 Driver Card Series S20-11712-0 Publ. 9-AM681 E-Mail: denison@denisonhydraulics.com Internet: http://www.denisonhydraulics.com SYSTEM FEATURES SYSTEM FEATURES
More informationC224-E031A. Autograph AGS-J. Shimadzu Table-top Type Universal Tester
C224-E031A Autograph AGS-J Shimadzu Table-top Type Universal Tester All the necessary functions in a compact body! AGS-J Autograph AGS-J Shimadzu Table-top Type Universal Tester All the necessary functions
More informationUsing Advanced Limit Line Features
Application Note Using Advanced Limit Line Features MS2717B, MS2718B, MS2719B, MS2723B, MS2724B, MS2034A, MS2036A, and MT8222A Economy Microwave Spectrum Analyzer, Spectrum Master, and BTS Master The limit
More informationPV Master OPERATION MANUAL
PV Master OPERATION MANUAL GoodWe Technical Services Center December, 2017 Ver. 1.00 BRIEF INTRODUCTION PV Master is an external application for GoodWe inverters to monitor or configure inverters or to
More informationEBIKE DIAGNOSIS FLOWS
EBIKE DIAGSIS FLOWS 1 SUMMARY Check Tool Instructions 2 Display and Controller check tool 3 Display Holder check tool 7 Motor check tool 8 Battery check tool 9 Torque Sensor check tool 12 Customized controller
More informationUSERS MANUAL MCD REMOTE OPERATOR
USERS MANUAL MCD REMOTE OPERATOR Order Code: 175G9004, 175G3061 Contents Contents Introduction...2 Important User Information...2 General Description...2 Symbols Used in this Manual...2 Installation...3
More informationGenerator Sets Controller 210. Operation Manual. Ver1.0
Generator Sets Controller 210 Operation Manual Ver1.0 Note This information could include technical inaccuracies or typographical error. Manufacturer may make improvements and/or changes in the product(s)
More informationFurnace Web Site FAQs. Pro Press 100 / Pro 100 / Pro 100 plus. Lift. Belt Noise
Furnace Web Site FAQs Pro Press 100 / Pro 100 / Pro 100 plus Lift Belt Noise A Worn belt Over time the belt may become dry or worn due to heat and travel. Replace the belt Tight If the belt was recently
More informationFlowrite EA 599 Series SKB/C/D 62UA Series Electronic Valve Actuator 24 Vac Proportional Control Advanced Features
Flowrite EA 599 Series SKB/C/D 62UA Series Electronic Valve Actuator 24 Vac Proportional Control Advanced Features Technical Instructions Document No. 55-77 EA-599-8 April 3, 24 EA228R EA379R SKB/C SKD
More informationOperating Instructions EVG620 Aligner
Operating Instructions EVG620 Aligner The tool uses 5 masks only. It can align to small pieces and up to a 4 wafer. Using the Tool for Top Side Alignment 1. Insure that the lamp is glowing by checking
More informationStatic Servohydraulic Universal Testing Machines
Materials Testing Systems 45 Static Servohydraulic Universal Testing Machines A B C D E F G H I J K L M N O P Q R S T 46 Materials Testing Systems Static Servohydraulic Universal Testing Machines for Load
More informationPlanting. Press to Highlight Configuration. Gauge Wheel Load Alarm. Value must be entered for your specific planter and parallel arm combination
To create a configuration, make the following button presses to start the Configuration Wizard and then follow the instructions given on the display. Planting Start of Configuration Wizard Enter Settings
More informationHydraulic Universal Testing Machine
WAW-E Series Computer-Controlled Electro-hydraulic Servo Universal Testing Machine Application: WAW-E Series Computer-Controlled Electro-hydraulic Servo Universal Testing Machine is suitable to test various
More informationHi-Z USB Wireless. Introduction/Welcome
Hi-Z USB Wireless Introduction/Welcome Thank you for selecting the Hi-Z Antennas USB Wireless system. The Hi-Z USB Wireless system provides control functions from a personal computer to operate a Hi-Z
More informationINSTALLATION, OPERATION and MAINTENANCE Manual
INSTALLATION, OPERATION and MAINTENANCE Manual Type VSD - Intelligent Valve Controller w/ Bluetooth and Capacitor Backup Module Basic Setup, Valve Diagnostics & Software Configuration Imtex Controls Limited
More informationTouch plate serial number. Please save this info here for use later:
Touch Plate Manual Touch plate serial number. Please save this info here for use later: Copyright Next Wave Automation All Rights Reserved. Version 2 April14th 2017 Updates of this manual are available
More informationTorque Wrenches
- 171 - Digital Torque Wrenches Digital Torque Wrenches The new AmPro digital torque wrenches are designed for simple and precise measurement of industrial, automotive, aerospace and many other applications.
More informationEco-Propel TM Variable Speed Pump Kit Instruction and Operation Manual, p/n Revision 0
Eco-Propel TM Variable Speed Pump Kit Instruction and Operation Manual, p/n 107065-01 Revision 0 May 20, 2016 Contents Introduction 2 Installation Pre-installation 3 Installation Procedure 4 Electrical
More informationSTAR. series. Servo proportional valve Rated flows up to 80 l/m. Features
STAR series 65 Servo proportional valve Rated flows up to 8 l/m Features Maximum operating pressure 15 bar ISO 172-4-4--92 mounting pattern Internal pilot supply (4 port) Suitable for -way or 4-way applications
More informationMATRIX LLC LEVEL CONTROL PANEL
MATRIX LLC LEVEL CONTROL PANEL Installation Operation Maintenance Manual 1-26-09 REV-0.3 1 INDEX Introduction. 3 Product Configurations..... 4 I/O Descriptions. 8 Operation o Intercooler, Accumulator,
More informationOPERATING MANUAL Digital Diesel Control Remote control panel for WhisperPower generator sets
Art. nr. 40200261 OPERATING MANUAL Digital Diesel Control Remote control panel for WhisperPower generator sets WHISPERPOWER BV Kelvinlaan 82 9207 JB Drachten Netherlands Tel.: +31-512-571550 Fax.: +31-512-571599
More informationCS 430RC. Solid De-icer Controller Configuration and Set-up Manual
CS 430RC Solid De-icer Controller Configuration and Set-up Manual 2/17 Table of Contents 1 Systems Modes of Operation 3 2 System Features 4 3 System Description 5 4 System Specifications 6 4.1 CS-430RC
More informationELECTRICAL MACHINES LAB.
ﺟﺎﻣﻌﺔ ﺟﺎزان ﻛﻠــﯿﺔ اﻟﮭﻨﺪﺳﺔ ﻗﺴــﻢ اﻟﮭﻨﺪﺳﺔ اﻟﻜﮭﺮﺑﺎﺋﯿﺔ Jazan University Engineering College Electrical Engineering Department ﻣﻌﻤﻞ اﻵﻻت اﻟﻜﮭﺮﺑﺎﺋﯿﺔ ELECTRICAL MACHINES LAB. ھﻨﺪﺳﺔ ﻛﮭﺮﺑﺎﺋﯿﺔ - 421 ھﻜﮫ : اﻟﻤﻘﺮر
More informationInlet Controller SB3500 USER'S MANUAL
Inlet Controller USER'S MANUAL NOTICE Every effort has been made to ensure that this manual is complete, accurate and up-to-date. The information contained in it is however subject to change without notice
More information