Meuangvang Development Co.LTD Standard Working Procedure 013 Jump Starting Vehicles

Transcription

1 1. Application To provide a standard work practice for as required in accordance with Safety Management Program 2. Revision Schedule Rev # Old Section Ref New Section Ref Description of Changes 0 New document created 3. Table of Contents 1 Application 8 Definitions 2 Revision Schedule 9 Purpose & Expected outcomes 3 Table Of Contents 10 Task 4 Personal Protective Equipment 11 Written Assessment 5 Accountability 12 Improvement Suggestion 6 Training Requirements 13 Approval 7 Document Storage 14 MVDCSWP013 Jump Start Vehicles May 2008 Page 1

2 4. Personal Protective Equipment (PPE) / Special Equipment Hard Hat Safety Glasses Reflective Clothing Gloves Special Equipment Set of heavy duty jumper leads with clamping jaws or receptacle fittings suitable for the application 5. Accountability Supervisors are to ensure employees have completed training and the assessment included in this SWP 6. Training Requirements Employees are to receive training in the correct procedure for 7. Document Storage The electronic master version of this document, together with the associated Forms and Templates, is stored on the Safety Managers computer. Safety Manager/ officer are responsible of maintaining the document. 8. Definitions (a) (b) jump starting vehicles and equipment not fitted with special jump start connections, and vehicles and equipment fitted with jump start receptacle connections MVDCSWP013 Jump Start Vehicles May 2008 Page 2

3 9. Purpose and Expected Outcomes and Flowchart To provide a standard process for the creation, review, authorisation and issue of documents which require control, specifically those operational documents shown in the document structure below. To ensure a common format of documentation is followed, to eliminate duplication and to ensure accurate and current information is readily available to all employees. PROCESS FLOWCHART. Safety Management Program Policies and Rules Standard Work Procedures Risk Assessment Hazard Identification Training Management Planning Training,& Training Manuals Competency Assessments MVDCSWP013 Jump Start Vehicles May 2008 Page 3

4 10. Tasks Task Steps Hazards Additional Information and Controls Detail of each step in the task, presented in a logical sequence. Identification of any hazards involved with the task step. Any other relevant detail or information that will assist with the performing of the task and any requirements for risk mitigation. Inspect jumper leads for frayed Checking Equipment ends, exposed wires, cuts or punctures in the insulation and check the ends for loose or burned connections. Check Vehicles Ensure vehicle park brakes are on and park in neutral Task Steps Hazards Additional Information and Controls Detail of each step in the task, presented in a logical sequence. Identification of any hazards involved with the task step. Any other relevant detail or information that will assist with the performing of the task and any requirements for risk mitigation. Jump Start Using Jump Start Fittings/Lead Connect jumper lead to vehicle/equipment requiring jump start via special connection. Connect other end to vehicle/equipment to be used for boost. Start boost vehicle and leave running. Start vehicle being jump started. Disconnect leads in reverse order. Move boost vehicle to a safe distance before attempting to operate the vehicle/equipment. MVDCSWP013 Jump Start Vehicles May 2008 Page 4

5 Task Steps Hazards Additional Information and Controls Detail of each step in the task, presented in a logical sequence. Jump Starting Using Clamp Type Jumper Leads The following sequence must be followed to avoid sparks/arcing: Identification of any hazards involved with the task step. Any other relevant detail or information that will assist with the performing of the task and any requirements for risk mitigation. Always start by attaching the red positive lead to the battery pole of flat battery vehicle first (+ve Red) Then connect the other end of this red lead to the battery pole of boost battery (+ve Red) Connect the negative black lead to the chassis or engine, or negative pole of the battery on boost vehicle. Connect the other end of this black lead to the chassis or engine in an area away from the flat battery. Start the boost vehicle and leave running. Start the vehicle being jump started. Disconnect jumper leads in reverse order, black earth lead first, then red positive lead. Move boost vehicle to a safe distance before attempting to operate the vehicle/equipment. MVDCSWP013 Jump Start Vehicles May 2008 Page 5

6 MVDCSWP013 Jump Start Vehicles May 2008 Page 6

7 11. Written Assessment 1. I have received training in jump starting vehicles? 2. How should the vehicles be parked? 3. If you answered no to the first question what are you going to do about it? 4. What do you check the jumper leads for? 5. List 2 hazards you need to be aware of before jump starting a vehicle? I have read and understood this procedure and have had any questions in regard to this procedure thoroughly explained. Name: Signature: Date: Training Coordinator: Signature: Date: MVDCSWP013 Jump Start Vehicles May 2008 Page 7

8 12. Improvement Suggestion Possible Cause Corrective Action Additional Information 13. Approval Revision 01 øéêö ê Approved by(position)»ñ»º  (ª ÁÎ ) Signature of Approver ì¾ À ñ º øé»ñ»º Date ñ ê Prepared by ½ ¼  P Brears Safety Consultant Reviewed Approved MVDCSWP013 Jump Start Vehicles May 2008 Page 8