Risk Assessment Form

Size: px
Start display at page:

Download "Risk Assessment Form"

Transcription

1 Assessment Form Oil Salvage Limited Assessment Record Activity: Collection of Garage Waste Using Box Vans Ref Number: RA04 Having assessed the hazards and risks, I believe that if the control measures identified are applied Oil Salvage Ltd will, so far as is reasonably practicable reduce the risk to an acceptable level Assessed by: R. Salamanca Signed: Date: 25/01/17 Approved by: M.Vernon Signed: Date: 25/01/17 Summary of s (Residual) Hazard Hazard Hazard Slips, trips & falls 1D Work at Height 1C Hazardous Substances 1C Manual Handling 1C Unfamiliar with customer sites 1C Driving 1C Refuelling 1D Traffic Movements 1C Traffic Movements around client site 1C Driver Fatigue 1C Fire/Explosion 1C Traffic Movements around client site 1C P.P.E. Requirements Gloves Safety footwear Overalls Hearing protection Dust Mask Respiratory Eye Protection Face Shield Hi-Viz BS EN 374:1994, BS EN 388:1994 BS EN ISO20345:2011 Overalls BS EN 166 BS EN ISO 20471:2013 Class 2

2 What are the hazards Slips, trips & falls Manual Handling Refuelling Driver fatigue Who might s Contractors other road users How might they Injuries caused by slipping, tripping or falling Injuries through poor lifting technique Inherent Control Measures Residual L S R L S R 4 D 4D 4 C 4C Contact with Diesel fuel 2 D 3D Road accident leading to injury 4 C 4C The driver is visiting a customer s site so has no control over the condition of the site s flooring so the driver must visually assess the floor s condition looking for oil spills, wet patches potholes etc. before entering. Storage areas may also be outside so ice / snow must be assessed for. The driver is to wear good safety footwear with good grip. Hazardous, slippy conditions must be reported back to management to await further instructions. Point of work risk assessment to be completed Spill kits are on vehicles The drums and batteries are heavy objects. Filers/rags are collected in wheelie bins which are on wheels to aid movement. Van fitted with tail lift to get items into and out of van. Tail lift subject to inspections under LOLER. Lifting devices are provided to aid in the lifting and movement of items Lifting devices must be used at all times. All drives are to be trained in manual handling techniques. Drivers to check route before moving equipment. Seek assistance if required to hold doors open etc. Drivers to inspect equipment before use Damaged or missing equipment must be reported to management for immediate replacement. Each driver has a two week induction period with another experience driver. COSHH assessments carried out for diesel Operatives to wear PVC gloves when refuelling Shift patterns are designed to minimise the risk of driver fatigue. Drivers instructed to take breaks if they become tired 1 D 1D 1 D 1D Are further controls required?

3 What are the hazards Working at height Unfamiliar with customer sites Traffic Movements Fire/explosion Who might s Drivers Customer employees and others s contractors general public How might they Fall off the back of the box van or while getting into cab Injury through lack of awareness of hazards Impact with a vehicle Heat from fire causing burns Fumes/smoke from fire Inherent Control Measures Residual L S R L S R 4 C 4C Safe means of access provided on all vehicles. Tail lift must be used as per operational instructions. Tail lifts inspected in accordance with LOLER Vehicles regularly cleaned to remove oil, grease and dirt. Safety footwear, gloves & overalls to be worn at all times. Driver to use hand grabs when getting in/out of cab. Keep minimum equipment at height. All drives have undergone training in working at height during induction. Drivers regularly visit most sites and are aware of the hazards and other safety issues on site. Point of work risk assessment to be used If required by site driver will do site induction Sales/admin will get as much information as possible before delivery/collection regarding safety issues prior to first collection/delivery Drivers to obey PPE requirements for customer sites. Vehicles park in designated parking/loading area Avoid reversing where possible. Newer vehicles fitted with cameras and audible warning to aid or warn of reversing vehicle Assistance may be required in some circumstances to aid reversing Driver to wear hi viz vest or jacket. When on a new site the driver must seek guidance from the site supervisor over traffic routes and the transport management plan. All box vans are serviced and inspected and records available. Fire extinguishers provide. All drivers trained in actions to take in the event of a fire. Staff provided with anti-static overalls. No smoking allowed in the workplace including vehicles Drums of mixed fuels and oils to be sealed when moving Are further controls required?

4 What are the hazards Hazardous substances eg Burns (battery acid) Driving Who might s Contractors Other road users How might they Contact with acid Mercury from the fluorescent tubes & lamps Road accidents leading to injury Inherent Control Measures Residual L S R L S R 4 C 4C 4 C 4C Vehicle batteries contain sulphuric acid that is corrosive. Drivers are to ensure that all batteries are capped before moving. The batteries are to be stored inside the battery box for transportation. PPE to be worn when handling batteries including eye protection, gloves, overalls and sturdy safety boots. All materials in correctly marked containers Fluorescent tubes are stored in boxes for transport to avoid breaking them. Any breakages are contained. All drivers are trained and hold the relevant licence for the vehicle Time allocated at start of each day for drivers to carryout pre use checks of vehicles Drivers to obey speed limits Driver licence checks carried out annually Mobile phones are not to be used while driving Position of all vehicles can be tracked on computer at office. Ensure head height of vehicle is sufficient especially on commercial vehicle forecourts and customer sites to pass underneath. List further controls required? Traffic Movements around client site Impact with a vehicle -Vehicles park in designated parking/loading area. -Avoid reversing where possible (Use rear parking camera a Mirrors). -Newer vehicles fitted with cameras and audible warning to aid or warn of reversing vehicles within its vicinity. -Assistance may be required in some circumstances to aid reversing (This will have be a trained Reversing Assistant). -Driver to wear hi viz clothing (Drivers are all in Orange coveralls which have reflective strips on them). -When on an unfamiliar site the driver must seek guidance from the site supervisor over traffic routes and the transport management plan.

5 Traffic Movements around client site Impact with a vehicle -Vehicles park in designated parking/loading area. -Avoid reversing where possible (Use rear parking camera a Mirrors). -Newer vehicles fitted with cameras and audible warning to aid or warn of reversing vehicles within its vicinity. -Assistance may be required in some circumstances to aid reversing (This will have be a trained Reversing Assistant). -Driver to wear hi viz clothing (Drivers are all in Orange coveralls which have reflective strips on them). -When on an unfamiliar site the driver must seek guidance from the site supervisor over traffic routes and the transport management plan.

6 Record of Further Actions from Assessment Assessment Number RA04 Title Hazard Required Action Who When Date Completed Signature Note that this document forms part of your Safe System of Work (SSoW) and the precautions made within this document must be adhered too at all times. If you deem anything to be unsuitable please see your supervisor or Compliance Manager as soon as possible before you carry out any works. Name Signature Date X X X

7 Probability Matrix Severity A B C D E PTD or < 3 Fatalities 3 or more fatalities Major Injury or Health Effect Minor Injury or Health Effect Slight Injury or Health Effect 5 Frequent 5A 5B 5C 5D 5E 4 Likely 4A 4B 4C 4D 4E 3 Occasional 3A 3B 3C 3D 3E 2 Seldom 2A 2B 2C 2D 2E 1 Improbable 1A 1B 1C 1D 1E Assessment risk Index Criteria Unacceptable under existing controls requires immediate action Manageable under risk control & mitigation. Requires Management approval Acceptable after review of the operation. Requires monitoring to ensure controls are effective. To look at what more can be done to reduce risk. Acceptable if controls implemented.

8 Part 2. THINK Part 1. STOP Date Project Title POINT OF WORK RISK ASSESSMNET (PoWRA) Location PLEASE TICK YES NO Before you start Are you at the correct location? Do you have the right documentation for the job? Do you have the right PPE for the job? Are tools, leads & plant tested? Are ladders inspected? Is lifting equipment inspected? If you have answered 'no' to any of the above, please take the required action or report this to your supervisor. IF IN DOUBT, ASK! Health & Safety Assessment (If the hazard is present, tick the box) Fall from Height Confined Space Adverse Weather Falling or flying objects Dust to you from your work Chemical or harmful substances Fumes to others from your work Heat, Fire or Explosion Noise Stored energy or insecure load Asphyxiation or drowning Vibration Traffic or moving vehicles to plant Electricity Other, state: Contact with stationary object Manual Handling Object overturning or collapsing Slips, trips or falls on the same level Poor Lighting Temperature If Required, you must have a Rescue Plan in place. Provide brief details. You must always be able to provide a way of safe escape in the event of something going wrong.

9 Part 4. REVIEW Part 3. ACT If no control measures are in place for the hazards identified above, then Part 3 (On the next page) needs to be completed and appropriate control measures out in place before work commences Additional Safety Assessment Remaining Hazard (Identified Overleaf) Control Measure or Precautions High Medium Low Are there any lessons for next time? Has the work created any new hazards? End of Job Review If you have answered 'Yes' to either of these questions, make a breif note and tell your supervisor. YES NO YES NO Has a Assessment briefing taken place? Who performed the briefing: Name: Date:

Revision Date Reviewed By Authorised By. V3 22/01/2018 D Newton P FitzPatrick. processes Task. Coupling and Uncoupling Coupling.

Revision Date Reviewed By Authorised By. V3 22/01/2018 D Newton P FitzPatrick. processes Task. Coupling and Uncoupling Coupling. Safe Working Procedure: TAT SWP 003v3 Coupling and Uncoupling Risk Assessment Ref: TAT - RA003.3 Revision Date Reviewed By Authorised By V3 22/01/2018 D Newton P FitzPatrick Changes to coupling and uncoupling

More information

GENERIC RISK ASSESSMENT - TRAVEL BY COACH

GENERIC RISK ASSESSMENT - TRAVEL BY COACH THE MANAGEMENT OF HEALTH AND SAFETY AT WORK REGULATIONS 1999 GENERIC RISK ASSESSMENT - TRAVEL BY COACH DATE OF ASSESSMENT March 017 DATE OF REVIEW March 018 NEXT REVIEW DATE March 019 1 Risk Assessment

More information

MORELAND CITY COUNCIL Operations Centre 7-9 Walter Street Hadfield Vic 3046 Tel:

MORELAND CITY COUNCIL Operations Centre 7-9 Walter Street Hadfield Vic 3046 Tel: MORELAND CITY COUNCIL Operations Centre 7-9 Walter Street Hadfield Vic 3046 Tel: 8311 4300 Approved by the Walter Street OHS committee Date: Operation Brief Description of Activity Waste Collection Using

More information

ESSENTIAL SAFETY RESOURCES

ESSENTIAL SAFETY RESOURCES ESSENTIAL SAFETY RESOURCES GS-3009 DRIVING SAFETY Originator: Safety Advisor s Signature: Type Name Approval: HSE Manager s Signature: Type Name Approval: Operations Manager s Signature: Type Name Table

More information

State existing practical or management controls for this hazard

State existing practical or management controls for this hazard by this hazard () Complete the assessment table for each hazard identified. Staff/Passengers (SP) Employees (E) Students (S) Others (O) Special Needs (SN) State what control measures are in use at the

More information

Policy Sponsor: Assistant Vice President. Responsible Unit: Facilities Management

Policy Sponsor: Assistant Vice President. Responsible Unit: Facilities Management Policy Sponsor: Assistant Vice President Approval Date: January 2010 Gas Powered Pole Pruners/Saws Safe Work Instructions Responsible Unit: Revisions: Service: Environmental Services Shop: Grounds and

More information

TJ Drivers Knowledge Assessment

TJ Drivers Knowledge Assessment Name Position Date 1. What must I wear whilst carrying out my daily operations? Protective Footwear T Shirt and Trainers Sun glasses High Visibility Clothing Safety Helmet Baseball Cap Safety Glasses if

More information

MUNICIPAL SOLID WASTE OPERATIONS SAFETY AUDIT/SURVEY TOOL. Injury prevention during solid waste operations

MUNICIPAL SOLID WASTE OPERATIONS SAFETY AUDIT/SURVEY TOOL. Injury prevention during solid waste operations MUNICIPAL SOLID WASTE OPERATIONS SAFETY AUDIT/SURVEY TOOL Injury prevention during solid waste operations Instructions: This is a scored pro-active safety auditing tool designed for periodic use to reduce

More information

SAFETY ALERT - # TOWING INCIDENT

SAFETY ALERT - # TOWING INCIDENT Incident Summary: An injury recently occurred on an oil and gas site undergoing production workover activities. A worker had the first three fingers of his right hand pinched and severely injured in the

More information

Quarries National Joint Advisory Committee (QNJAC) Plant Safety. Information Sheet 3. November Drill Rigs Maintenance and Safety checks

Quarries National Joint Advisory Committee (QNJAC) Plant Safety. Information Sheet 3. November Drill Rigs Maintenance and Safety checks Quarries National Joint Advisory Committee (QNJAC) Plant Safety Information Sheet 3 November 2011 Drill Rigs Maintenance and Safety checks This Information Sheet has been developed by the Quarries National

More information

Technical Test Theory Dump Truck - Articulated Chassis A56

Technical Test Theory Dump Truck - Articulated Chassis A56 1 a) Give ONE advantage and b) TWO disadvantages of rear-mounted cameras. 2 What is the purpose of a ROPS cab? 3 Give TWO reasons why the dump truck operator should have an understanding of the type of

More information

Technical Test Theory Wheeled Loading Shovel A21

Technical Test Theory Wheeled Loading Shovel A21 1 Name THREE ways that a plant operator can contribute in ensuring repeat business with the client or principal contractor. 2 Using the Operator s Manual, state the figure for the tyres operating pressure.

More information

RTV900 Safety Code. Please contact us for further information: Tel: Visit:

RTV900 Safety Code. Please contact us for further information: Tel: Visit: RTV900 Safety Code DEALER S STAMP Please contact us for further information: Tel: 0800 023 1111 Visit: www.kubota.co.uk Email: sales@kubota.co.uk Kubota (UK) Ltd, Dormer Road, Thame, Oxfordshire. OX9 3UN

More information

Dump Truck. 1. What is the definition of, or how can a hazard be described?

Dump Truck. 1. What is the definition of, or how can a hazard be described? 57 1. What is the definition of, or how can a hazard be described? 2. What is the purpose of a risk assessment? 3. List SIX typical subject areas that should be covered in a site induction. Roles and responsibilities

More information

Waste & Litter Collection utilizing the Rear Loading Compactor

Waste & Litter Collection utilizing the Rear Loading Compactor MORELAND CITY COUNCIL Operations Centre 7-9 Walter Street Hadfield Vic 3046 Tel: 8311 4300 Approved by the Walter Street OHS committee Date: Operation Brief Description of Activity Waste & Litter Collection

More information

Dump Truck - Articulated Chassis A56

Dump Truck - Articulated Chassis A56 Dump Truck - Articulated Chassis A56 What is the definition of, or how can a hazard be described? What is the purpose of a risk assessment? List SIX typical subject areas that should be covered in a site

More information

TOOL BOX TALKS. Municipality General Safety Rules SAFE (7233)

TOOL BOX TALKS. Municipality General Safety Rules SAFE (7233) TOOL BOX TALKS Municipality General Safety Rules Safety is of the utmost importance in the discharge of work or duty. These safety rules are designed to promote proper safety practices on the job. They

More information

MORELAND CITY COUNCIL Operations Centre 7-9 Walter Street Hadfield Vic 3046 Tel:

MORELAND CITY COUNCIL Operations Centre 7-9 Walter Street Hadfield Vic 3046 Tel: MORELAND CITY COUNCIL Operations Centre 7-9 Walter Street Hadfield Vic 3046 Tel: 8311 4300 Approved by the Walter Street OHS committee Date: September 2014 Operation Brief Description of Activity Waste

More information

6.0 Vehicles and machinery

6.0 Vehicles and machinery Code of Practice for Preventing Injury and Occupational Ill Health in Agriculture 6.0 Vehicles and machinery 6.1. Risk assessment Farm vehicles and machinery account for the highest proportion of farm

More information

SAFE OPERATION 1. BEFORE OPERATION

SAFE OPERATION 1. BEFORE OPERATION 1 The best insurance against accidents is to abide by the safety regulations. Read and understand this manual carefully before operating the excavator. Every user, however experienced, should carefully

More information

Quarries National Joint Advisory Committee (QNJAC) Plant Safety. Information Sheet 1. November Mobile Plant Maintenance and Safety checks

Quarries National Joint Advisory Committee (QNJAC) Plant Safety. Information Sheet 1. November Mobile Plant Maintenance and Safety checks Quarries National Joint Advisory Committee (QNJAC) Plant Safety Information Sheet 1 November 2011 Mobile Plant Maintenance and Safety checks This Information Sheet has been developed by the Quarries National

More information

V2 02/11/15 D Newton P FitzPatrick. Changes to coupling and uncoupling processes Task. Coupling and Uncoupling Coupling. Uncoupling.

V2 02/11/15 D Newton P FitzPatrick. Changes to coupling and uncoupling processes Task. Coupling and Uncoupling Coupling. Uncoupling. Safe Working Procedure: TAT Coupling and Uncoupling SWP 003 v2 Risk Assessment Ref: TAT - RA003 Revision Date Reviewed By Authorised By V2 02/11/15 D Newton P FitzPatrick Changes to coupling and uncoupling

More information

Dump Truck. 1. What is the definition of, or how can a hazard be described?

Dump Truck. 1. What is the definition of, or how can a hazard be described? rticulated Chassis 56 1. What is the definition of, or how can a hazard be described? 2. What is the purpose of a risk assessment? 3. List SIX typical subject areas that should be covered in a site induction.

More information

Airport Operating Standard. Spill Prevention and Response

Airport Operating Standard. Spill Prevention and Response Airport Operating Standard Spill Prevention and Response June 2018 Contents Introduction 2 Responsibilities 3 Prevention 4 Response 6 Effluent spills 8 Emergency facilities 8 Further enquiries, contacts

More information

SAFE WORK PROCEDURE SWP 053 TRACTOR OPERATION DOC. NO. D15/81228

SAFE WORK PROCEDURE SWP 053 TRACTOR OPERATION DOC. NO. D15/81228 MORELAND CITY COUNCIL Operations Centre 7-9 Walter Street Hadfield Vic 3046 Tel: 8311 4300 Approved by the Walter Street OHS committee Date: Operation Brief Description of Activity Collection & Disposal

More information

A56. Rear Tipping Dump Truck

A56. Rear Tipping Dump Truck A56 Rear Tipping Dump Truck General Safety Information for CPCS Technical Test This is for guidance purposes only and does not relate directly to specific CPCS technical test questions. It should only

More information

SWI/001 KESCRG SAFE WORKING INSTRUCTIONS FOR GENERATORS

SWI/001 KESCRG SAFE WORKING INSTRUCTIONS FOR GENERATORS SWI/001 KESCRG SAFE WORKING INSTRUCTIONS FOR GENERATORS Safe Working Instructions for Generators Page 1 of 5 1. Revision Table Revision Date Comments 1 01/03/2012 First Issue 2. Objectives 2.1. The objective

More information

Safe Work Instructions Tools and Equipment

Safe Work Instructions Tools and Equipment Safe Work Instructions Version 1.00! 23 March 2015 Table of Contents PURPOSE AND SCOPE...4 HAND TOOLS...6 ELECTRIC POWER TOOLS...7 PETROL POWERED TOOLS...9 PORTABLE ELECTRICITY GENERATOR...12 PNEUMATIC

More information

Technical Test Theory Telescopic Handler A17

Technical Test Theory Telescopic Handler A17 1 State the possible effect of lifting a load whilst facing downhill on a slope. 2 How can a qualification or card benefit a plant operator? 3 According to regulations (such as Lifting Operations and Lifting

More information

SSMP ELEMENT 4 O & M Program APPENDIX 4.3. Sewer Pipe Cleaning Standard Operating Procedures (SOPs)

SSMP ELEMENT 4 O & M Program APPENDIX 4.3. Sewer Pipe Cleaning Standard Operating Procedures (SOPs) SSMP ELEMENT 4 O & M Program APPENDIX 4.3 Sewer Pipe Cleaning Standard Operating Procedures (SOPs) City of San Mateo CODE OF SAFE PRACTICES Table of Contents A B C D E F G Air Compressor and Pressure Vessel

More information

Employee Safety and Training Manual

Employee Safety and Training Manual Employee Safety and Training Manual (Forms may be used as a master or photocopies made. Signed forms should be kept with employees personnel file.) Safety Policy Safety Policy for ANNUALLY (Insert company

More information

Full time Bus Driver Job Description

Full time Bus Driver Job Description Full time Bus Driver Job Description Purpose of the Role A bus driver is responsible for driving a passenger carrying vehicle (PCV), providing good customer service and a safe and comfortable journey throughout

More information

Turbocharger / A100-L Original assembly instructions English

Turbocharger / A100-L Original assembly instructions English Assembly Instructions Turbocharger / A100-L Original assembly instructions English This document is valid for the A100-L series: A165-L, A170-L, A175-L, A180-L, A185-L, A190-L Purpose The assembly instructions

More information

Technical Test Theory Telescopic Handler A17

Technical Test Theory Telescopic Handler A17 1 Using the lifting capacity diagram for A17: a) what is the maximum lifting capacity at maximum height, b) what is the lifting capacity with the boom angle at 45 degrees and a boom extension of 2.5 metres

More information

Safe Driving Standards & Procedures

Safe Driving Standards & Procedures Type: POLICY Revision: 01 Owner: BRL Document Name: HSPOL 016 Status: Current Nov 2014 Review Date: February 1, 2018 Effective Date: 01 January 2015 Total Pages: 5 Scope: The following standard applies

More information

Guidance on safe procedures for staff and students in respect of road traffic incidents and breakdowns

Guidance on safe procedures for staff and students in respect of road traffic incidents and breakdowns Guidance on safe procedures for staff and students in respect of road traffic incidents and breakdowns If your vehicle breaks down, think first of all of other road users and; Get the vehicle safely off

More information

Ladder Safety Program

Ladder Safety Program Ladder Safety Program For Adopted LC-1022 Rev. 06/16 Page 1 I. Introduction The Organization recognizes that employees use ladders on a regular

More information

Ensure staff are trained in use of equipment

Ensure staff are trained in use of equipment Work at height Can you avoid working at height in the first place? No Yes Plan the task required Risk assess the task required Ensure staff are trained in use of equipment Ensure equipment has been correctly

More information

Personal Protective Equipment Standards

Personal Protective Equipment Standards Safe Working Procedure: TAT SWP 021v3 Risk Assessment Ref: DRV RA021v3 General Road Risk Revision Issue Date Reviewed By Authorised By V3 07/06/2017 D Newton P FitzPatrick Review Date 09/06/2018 Change

More information

Today, we re going to talk about battery safety. We ll discuss all the key issues associated with using batteries safely, including battery hazards,

Today, we re going to talk about battery safety. We ll discuss all the key issues associated with using batteries safely, including battery hazards, Today, we re going to talk about battery safety. We ll discuss all the key issues associated with using batteries safely, including battery hazards, battery charging, and battery maintenance. Although

More information

LEARNER GUIDE. Roller - LR. PO Box 2026 Mountain Gate VIC 3156 p: ABN: RTO: 21396

LEARNER GUIDE. Roller - LR. PO Box 2026 Mountain Gate VIC 3156 p: ABN: RTO: 21396 LEARNER GUIDE Roller - LR PO Box 2026 Mountain Gate VIC 3156 p: 03 9763 5449 ABN: 37 106 951 900 RTO: 21396 Assessor Guidelines Specific (Performance Assessment) ASSESSMENT INSTRUMENT SPECIATIONS The performance

More information

Turbocharger / TPS-H Original assembly instructions English

Turbocharger / TPS-H Original assembly instructions English Assembly Instructions Turbocharger / TPS-H Original assembly instructions English This document is valid for the TPS-H series: TPS44-H, TPS48-H, TPS52-H Purpose TPS-H turbocharger The assembly instructions

More information

Turbocharger / VTR..0, VTR..1 Original assembly instructions English

Turbocharger / VTR..0, VTR..1 Original assembly instructions English Assembly Instructions Turbocharger / VTR..0, VTR..1 Original assembly instructions English This document is valid for the VTR..0/..1 series: VTR160, VTR200, VTR250, VTR320, VTR400 VTR161, VTR201, VTR251,

More information

Make/Model/Type/Size Hands On- Training w/employee participation on starting and handling of Chain Saw. What Are The Risks?

Make/Model/Type/Size Hands On- Training w/employee participation on starting and handling of Chain Saw. What Are The Risks? -Tool Kit- Gloves, Hearing Protection, Face Shield, Due to the nature of our work, it is necessary at times to use chainsaws. In order to ensure your safety and the safety of your Brieser co-workers, it

More information

Vehicle battery BATTERY WARNING SYMBOLS BATTERY CARE

Vehicle battery BATTERY WARNING SYMBOLS BATTERY CARE Vehicle battery BATTERY WARNING SYMBOLS On the battery label, the warning signs are as follows: BATTERY CARE No smoking, no naked flames, no sparks. The battery may emit explosive gas. Keep away from children

More information

CPCS renewal test factsheet

CPCS renewal test factsheet CPCS renewal test factsheet Introduction to the CPCS renewal test The industry-led CPCS Management Committee has determined that key safety-related knowledge must be checked on each category prior to the

More information

Installation Instructions for Aux 101 Kit A044Z055

Installation Instructions for Aux 101 Kit A044Z055 Instruction Sheet 7-2013 Installation Instructions for Aux 101 Kit A044Z055 1 Introduction The information contained within is based on information available at the time of going to print. In line with

More information

Element 3: Musculoskeletal Hazards and Risk Control

Element 3: Musculoskeletal Hazards and Risk Control Manually and Mechanically Operated Load Handling Equipment There are many different types of lifting and moving equipment such as manually operated trucks and hoists and mechanically operated forklift

More information

RISK ASSESSMENT SUMMARY

RISK ASSESSMENT SUMMARY Assessment Ref no: RA.UK.009 (ERP UK Battery Box Risk Assessment) Assessed By: Steve Smith Approved By: John Redmayne Review Date: 13/10/2017 Approval Date: 13/10/2017 RISK ASSESSMENT SUMMARY Description:

More information

Ashvale Light Bulb Replacement - Qualitative Risk Assessment Ref: - LBRA/14 Brian Urquhart

Ashvale Light Bulb Replacement - Qualitative Risk Assessment Ref: - LBRA/14 Brian Urquhart Ashvale Light Bulb Replacement - Qualitative Assessment Ref: - LBRA/14 Brian Urquhart 14 Ashvale Light Bulb Replacement - Qualitative Assessment Review Date: Annually ( Assessments to be reviewed annually

More information

Technical Test Theory Lorry Loader A36

Technical Test Theory Lorry Loader A36 1 Using the Operator s Manual, state the hydraulic tank oil capacity OR oil type. Note: The Operator s Manual for the machine being used for the test MUST be available for reference by the candidate. 2

More information

Ride on roller Note: It is recommended that you read the Supporting Information page before you read this factsheet.

Ride on roller Note: It is recommended that you read the Supporting Information page before you read this factsheet. Ride on roller Note: It is recommended that you read the Supporting Information page before you read this factsheet. Preparation and completing work (Preparation) Ride on rollers fall into the category

More information

TLI Transport and Logistics Training Package. Companion Volume Implementation Guide - Range of Conditions Tables

TLI Transport and Logistics Training Package. Companion Volume Implementation Guide - Range of Conditions Tables TLI Transport and Logistics Training Package Release 1.0 Companion Volume Implementation Guide - Range of Conditions Tables Contents TLIC1013 Ride courier/delivery bicycle... 1 TLIC3003 Drive medium rigid

More information

BACKING BEST MANAGEMENT PRACTICES

BACKING BEST MANAGEMENT PRACTICES because SAFETY MATTERS. www.swana.org/safety BACKING BEST MANAGEMENT PRACTICES According to industry and OSHA data, backing represents approximately 25% of all injuries and accidents in the solid waste

More information

IMIVR06 Remove and transport heavy vehicles

IMIVR06 Remove and transport heavy vehicles Overview This unit is about recovering and transporting heavy upright vehicles from the roadside or similar hard, level standing. IMIVR06 1 Performance criteria You must be able to: P1 wear suitable personal

More information

Technical Test Theory Mobile Elevating Work Platform - Boom A26

Technical Test Theory Mobile Elevating Work Platform - Boom A26 1 Why are those who operate MEWPs generally regarded as safety-critical workers? 2 What are the possible outcomes of facing prosecution for not complying with legislation and regulations? 3 How do stabilisers

More information

INSTRUCTION MANUAL. Stephenson Road Speedwell Industrial Estate Staveley Chesterfield S43 3JN

INSTRUCTION MANUAL. Stephenson Road Speedwell Industrial Estate Staveley Chesterfield S43 3JN INSTRUCTION MANUAL Stephenson Road Speedwell Industrial Estate Staveley Chesterfield S43 3JN Telephone: 0800 1300 402 Fax: 01246 471 277 Website: www.morclean.com Email: information@morclean.com Contents

More information

TargetSolutions ONLINE COURSE CATALOG

TargetSolutions ONLINE COURSE CATALOG ONLINE COURSE CATALOG 1 TargetSolutions delivers employee training that helps public entities mitigate risk, We reduce believe claims a well-trained and save police money. department is a safer, more efficient

More information

Articulated Dumper. pre use check sheet page 1/5. How to use this check sheet:

Articulated Dumper. pre use check sheet page 1/5. How to use this check sheet: pre use check sheet page 1/5 How to use this check sheet: Plantshifter.com has created a whole range of pre use check sheets, these sheets are free to download to help you maintain you plant and machinery

More information

TABLE OF CONTENTS SECTION TITLE PAGE NUMBER

TABLE OF CONTENTS SECTION TITLE PAGE NUMBER Worker Falls from Trailer Type of Incident: Fatality Date of Incident: January 29, 2009 TABLE OF CONTENTS SECTION TITLE PAGE NUMBER 1.0 DATE AND TIME OF INCIDENT 3 2.0 NAME & ADDRESS OF PRINCIPAL PARTIES

More information

A Guide to lifesaving rule investigation: Always obey the speed limit

A Guide to lifesaving rule investigation: Always obey the speed limit A Guide to lifesaving rule investigation: Always obey the speed limit Author Lee Parlett, Corporate Investigation and Assurance Manager Function STE Date October 2015 Version 1.3 Always obey the speed

More information

2500 LB ELECTRIC A-FRAME JACK OWNER S MANUAL

2500 LB ELECTRIC A-FRAME JACK OWNER S MANUAL 2500 LB ELECTRIC A-FRAME JACK OWNER S MANUAL SPECIFICATIONS: Models Applicable: 2500 lb Electric A-Frame Jack Maximum Lift Capacity: 2500 lbs (continuous use) Retracted Height: 31 3 /8 Vertical Travel:

More information

North Dakota State University Grounds Maintenance Equipment

North Dakota State University Grounds Maintenance Equipment North Dakota State University Grounds Maintenance Equipment I. Introduction Grounds maintenance equipment is an important part of the work activities on NDSU campus. They can make grounds maintenance jobs

More information

1. Cranes. 3. Hazardous Chemicals. 4. Signs. 2. Trenching and Excavations

1. Cranes. 3. Hazardous Chemicals. 4. Signs. 2. Trenching and Excavations A Safe Operation Safety Tips for Heavy Construction 1. Cranes Cranes are a common piece of equipment on heavy construction jobsites. Always perform a walk around inspection before and after each shift

More information

Motive Power. Network Power. Chargers. Bloc Batteries. Accessories. Service

Motive Power. Network Power. Chargers. Bloc Batteries. Accessories. Service The Eternity Technologies range is built using only the highest quality and most efficient production processes at our state-of-the-art manufacturing centre in the UAE. It is this innovation, modern design

More information

Guardian Electrical Solutions Ltd DRIVING AT WORK POLICY

Guardian Electrical Solutions Ltd DRIVING AT WORK POLICY 1. Introduction Guardian recognises that it employs a number of staff who are required as part of their employment to operate vehicles whilst at work. In this context driving at work means 'driving whilst

More information

Below are details for liquid waste haulers on the process for discharging domestic wastewater at SA Water septic waste disposal stations (SWDS).

Below are details for liquid waste haulers on the process for discharging domestic wastewater at SA Water septic waste disposal stations (SWDS). Liquid hauled waste Discharging domestic hauled waste Once a liquid waste hauler has authorisation and is issued their vehicle swipe cards, they must ensure all drivers attend the relevant SA Water/ Allwater

More information

TELESCOPIC LADDER MODEL NO: TL-2B / TL-3B

TELESCOPIC LADDER MODEL NO: TL-2B / TL-3B TELESCOPIC LADDER MODEL NO: TL-2B / TL-3B PART NO: 3500240 / 3500242 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0918 - ISS 1 INTRODUCTION Thank you for purchasing this CLARKE telescopic

More information

waste collection Overview Vehicle Service Management Material Handlers Drivers % 10% 20% Other 30%

waste collection Overview Vehicle Service Management Material Handlers Drivers % 10% 20% Other 30% waste collection 72 2006-2012 768 compensable injuries Cost almost $28 million Resulted in over 122,000 days of time-loss A compensable rate of 6.9 per 100 FTE or 1 in 15 employees Figure 53. Compensable

More information

Motive Power. Network Power. Chargers. Bloc Batteries. Accessories. Service

Motive Power. Network Power. Chargers. Bloc Batteries. Accessories. Service The Eternity Technologies range is built using only the highest quality and most efficient production processes at our state-of-the-art manufacturing centre in the UAE. It is this innovation, modern design

More information

SAFE WORK PROCEDURE LOCATION OF WORK WRITTEN BY: APPROVED BY: DATE: LAST REVISION

SAFE WORK PROCEDURE LOCATION OF WORK WRITTEN BY: APPROVED BY: DATE: LAST REVISION Page 1 of 5 LOCATION OF WORK WRITTEN BY: APPROVED BY: DATE: LAST REVISION All Schools Lorie Carriere Jason Graham Donna Hancox Gordon Howe April 27, 2010 March 8, 2017 HAZARDS PRESENT Sun burns Muscle

More information

Li-ion Cordless Screwdriver

Li-ion Cordless Screwdriver Li-ion Cordless Screwdriver HPC-0023 Please note that your safety is your personal responsibility PLEASE READ BEFORE USE AND RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. IMPORTANT NOTE: ALWAYS CHECK

More information

SeekTech Inductive Clamp

SeekTech Inductive Clamp Inductive Clamp Manual SeekTech Inductive Clamp! Read this Operator s Manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock,

More information

360 o Excavator. pre use check sheet page 1/5. How to use this check sheet:

360 o Excavator. pre use check sheet page 1/5. How to use this check sheet: pre use check sheet page 1/5 How to use this check sheet: Plantshifter.com has created a whole range of pre use check sheets, these sheets are free to download to help you maintain you plant and machinery

More information

Electrical Safety Program

Electrical Safety Program Electrical Safety Program Medford Area Public School District 124 West State St School District: Medford, WI 54451 715 748 4620 Review Date(s): January 2018 Program Dave Makovsky Coordinator: Purpose and

More information

Driver safety guide. Winter means business

Driver safety guide. Winter means business Driver safety guide Winter means business Winter. Bring it on. Because your business can t afford to stop over winter, neither can you. Making sure your vans and drivers are ready for anything the season

More information

Management Plan for Aerial Lifts (ANSI/SLA ) ISD #535

Management Plan for Aerial Lifts (ANSI/SLA ) ISD #535 Management Plan for Aerial Lifts (ANSI/SLA 92.3-1990 1926.453) ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9½ Street Rochester, MN 55904 507-328-4507 Modification Date Document Modification

More information

SAFE WORK ENVIRONMENTAL METHOD STATEMENT SWEMS 0002 INSTALLATION & DISMANTLING OF 3 PLANK HANGERS PERIMETER RAIL

SAFE WORK ENVIRONMENTAL METHOD STATEMENT SWEMS 0002 INSTALLATION & DISMANTLING OF 3 PLANK HANGERS PERIMETER RAIL Safe Work and Environmental Method Statement. Contractor: Premium Scaffold Solutions Pty Ltd ABN # 42 149 568 981 Address: U5 8/10 Tullamarine Park Road TULLAMARINE VIC 3043 Workplace / Project: WRA Referred

More information

JHT ACN COMPANY INDUCTION JOHN HEGGART TRANSPORT. Ph: Fax: P.O BOX 1271 Warragul Vic

JHT ACN COMPANY INDUCTION JOHN HEGGART TRANSPORT. Ph: Fax: P.O BOX 1271 Warragul Vic JOHN HEGGART TRANSPORT PTY. LTD. ACN 094 311 243 COMPANY INDUCTION JOHN HEGGART TRANSPORT Ph:0356232231 Fax:0356232483 P.O BOX 1271 Warragul Vic 3820 Email: jht@dcsi.net.au Table of Contents. 1.0 JHT Goal

More information

CPCS renewal test factsheet

CPCS renewal test factsheet CPCS renewal test factsheet Introduction to the CPCS renewal test The industry-led CPCS Management Committee has determined that key safety-related knowledge must be checked on each category prior to the

More information

RELIANT HOLDINGS LTD AND ITS AFFILIATES Safety Management System. Preparation: Safety Mgr Authority: CEO Issuing Dept: Safety Page: Page 1 of 5

RELIANT HOLDINGS LTD AND ITS AFFILIATES Safety Management System. Preparation: Safety Mgr Authority: CEO Issuing Dept: Safety Page: Page 1 of 5 Preparation: Safety Mgr Authority: CEO Issuing Dept: Safety Page: Page 1 of 5 Purpose This program is written to be in compliance with local regulatory requirements and provide directives to managers,

More information

Light condition and operation Windshield glass condition Wiper blade condition Paint condition and corrosion Fluid leaks Door and hood lock condition

Light condition and operation Windshield glass condition Wiper blade condition Paint condition and corrosion Fluid leaks Door and hood lock condition GENERAL CHECKS Engine Compartment The following should be checked regularly: Engine oil level and condition Transmission fluid level and condition Brake fluid level Clutch fluid level Engine coolant level

More information

Service Truck Operator Ministry of Training, Colleges and Universities

Service Truck Operator Ministry of Training, Colleges and Universities On-site Orientation Service Truck Operator Ministry of Training, Colleges and Universities On-Site Orientation Service Truck Operator Program/Programme #P600108 Development Date: November 2008 Implementation

More information

Safe Driving Policy. 1. Objectives of the policy. 2. Code of conduct. 3. Responsibilities as an employee. Rev. Number 4 Page: Page 1 of 5

Safe Driving Policy. 1. Objectives of the policy. 2. Code of conduct. 3. Responsibilities as an employee. Rev. Number 4 Page: Page 1 of 5 Title: Safe Driving Policy : THG_POL_10 Page: Page 1 of 5 7/2/201 1. Objectives of the policy HS&E Chairman: : Safe Driving Policy a. To ensure that all company vehicles are operated by authorized drivers

More information

Coupling & Uncoupling of Trailers Tool Box Talk

Coupling & Uncoupling of Trailers Tool Box Talk Coupling & Uncoupling of Trailers Tool Box Talk Coupling & Uncoupling Coupling is the linking of a semi trailer to a towing truck, tractor unit, leading trailer or dolly. Uncoupling is the detachment of

More information

Activity / Exercise: Minibus Travel

Activity / Exercise: Minibus Travel Unit: 1011(Amesbury) Sqn Activity / Exercise: Minibus Travel RA Number: 1011/RA/Travel/2/MinibusTravel/2017 GRA: YES/NO (please delete as appropriate) Relevant Publications / Pamphlets/Procedures: 1. ACP5

More information

Snow and Ice Clearing Policy

Snow and Ice Clearing Policy Snow and Ice Clearing Policy DOCUMENT CONTROL: Version: 3.1 Ratified by: Risk Management Sub Group Date ratified: 16 December 2015 Name of originator/author: Environmental and Waste Manager Name of responsible

More information

Safety Training Topic ELECTRICAL SAFETY

Safety Training Topic ELECTRICAL SAFETY Safety Training Topic Purpose of Meeting To remind workers that electrical hazards can result in a serious injury. To reinforce electrical safety rules. To consider ways to protect yourself from electrical

More information

A23. Skid Steer Loaders

A23. Skid Steer Loaders A23 Skid Steer Loaders General safety information for CPCS technical test This is for guidance purposes only and does not relate directly to specific CPCS technical test questions. It should only be used

More information

SAFETY DIRECTIVE 2.0 DEPARTMENTS AFFECTED

SAFETY DIRECTIVE 2.0 DEPARTMENTS AFFECTED SAFETY DIRECTIVE Title: Ladders Issuing Department: Town Manager s Safety Office Effective Date: July 1, 2014 Approved: Gilbert Davidson, Town Manager Type of Action: New 1.0 PURPOSE This procedure has

More information

RDA HEALTH & SAFETY GUIDELINES

RDA HEALTH & SAFETY GUIDELINES RDA HEALTH & SAFETY GUIDELINES FOR CARRIAGE DRIVING GROUPS, THESE GUIDELINES SHOULD BE READ IN CONJUNCTION WITH THE CARRIAGE DRIVING SAFETY CODE IN SECTION 2(d) OF THE MEMBERSHIP MANUAL PLEASE BE AWARE

More information

Notice to all Users of the Weigh Northland Gantries

Notice to all Users of the Weigh Northland Gantries Notice to all Users of the Weigh Northland Gantries Purpose of the Gantry Compliance Process September 2017 Gantry Compliance Safe lifting equipment and competent operators are essential for minimising

More information

AIRSIDE OPERATIONAL SAFETY POLICY SPILL PREVENTION AND RESPONSE MARCH This document is uncontrolled when printed

AIRSIDE OPERATIONAL SAFETY POLICY SPILL PREVENTION AND RESPONSE MARCH This document is uncontrolled when printed AIRSIDE OPERATIONAL SAFETY POLICY SPILL PREVENTION AND RESPONSE MARCH 2015 Produced by Melbourne Airport in the interest of Airport Safety and Security Table of Contents SECTION ONE INTRODUCTION 1.1 Introduction...

More information

Pintle Hook Lesson Plan QUALIFICATION TRAINING PACKAGE

Pintle Hook Lesson Plan QUALIFICATION TRAINING PACKAGE DEPARTMENT OF THE AIR FORCE Headquarters US Air Force Washington, D.C. 20330-1030 QTP24-3-PTLHK 14 February 2017 Pintle Hook Lesson Plan QUALIFICATION TRAINING PACKAGE CONTENTS SECTION 1 OVERVIEW... 3

More information

Safety Resources p r o d u c t i n d e x

Safety Resources p r o d u c t i n d e x PRODUCT INDEX Safety Resources p r o d u c t i n d e x A Accessories eye protection...................... 22 23 lighting............................. 224 respirator................... 89 91, 93 95 Accumulation

More information

Safety. After working through this lesson, you should be able to:

Safety. After working through this lesson, you should be able to: Safety The summaries and their associated interpretations contained in this document are for general information only, not legal advice. To interpret or apply the law, you must consult the legally enforceable

More information

Hazards in Sanitation. Presented by: Josh Kemp, CSEA OSH Specialist

Hazards in Sanitation. Presented by: Josh Kemp, CSEA OSH Specialist Hazards in Sanitation Presented by: Josh Kemp, CSEA OSH Specialist Agenda Introduction Sanitation Fatalities Regulatory Requirements Other Sanitation Hazards Discussion What do you think are some of the

More information

DRIVER INDUCTION INFORMATION & CROSSRAIL VEHICLE SAFETY KIT

DRIVER INDUCTION INFORMATION & CROSSRAIL VEHICLE SAFETY KIT DRIVER INDUCTION INFORMATION & CROSSRAIL VEHICLE SAFETY KIT Supplementary Guide Contents 1. Introduction 1 2. Drugs and alcohol policies 2 3. Lorry routes 4 4. Crossrail safety requirements 5 5. Worksite

More information

Position Number Community Division/Region Yellowknife North Slave

Position Number Community Division/Region Yellowknife North Slave IDENTIFICATION Department Position Title Infrastructure Firefighter Position Number Community Division/Region 33-7791 Yellowknife North Slave PURPOSE OF THE POSITION The Firefighter is responsible for

More information

Safe use of quad bikes

Safe use of quad bikes INFORMATION SHEET Safe use of quad bikes On average, five people are killed on New Zealand farms each year in work-related quad bike incidents. In addition, there are more than 100 severe injuries each

More information