Parking Brake Shoe: Adjustments
|
|
|
- Deborah Francis
- 5 years ago
- Views:
Transcription
1 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 1 Parking Brake Shoe: Adjustments Transmission-Mounted Parking Brake Disassembly 1. Remove the Parking brake assembly from the vehicle.
2 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 2
3 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 3 2. Remove the parking brake filler plug and drain the lubricant. 3. Remove the parking brake vent.
4 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 4 4. Mount the parking brake in a vise so that the vise jaws grip the output flange yoke. 5. If required, use a hammer and punch to relieve the locking punch mark from the locknut flange so that the locknut can be freely turned. 6. Using a 2 9/16 Inch Hex Locknut Wrench T70T4252-D, remove the lock nut from the mainshaft. 7. Remove the lock nut washer. 8. Remove the parking brake from the vise.
5 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 5 9. NOTE: Use care not to lose the mainshaft shim. Using 2-3 Jaw Puller D8OL-1013-A or equivalent, separate the mainshaft, parking brake drum and output flange assembly from the parking brake housing. 10. Remove the mainshaft shim from the mainshaft.
6 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page CAUTION: The mainshaft, parking brake drum and output flange are factory balanced and serviced as an assembly only. Match mark and disassemble only if replacing the parking brake rear bearing or parking brake rear seal. Match mark the output flange, parking brake drum and mainshaft for assembly reference. 12. Mount the mainshaft, parking brake drum and output flange assembly in vise gripping the output flange yoke. 13. CAUTION: To maintain factory balance, do not remove the mainshaft-to-output flange bolts from the mainshaft. Remove the four 11/16 mainshaft-to-output flange nuts. 14. Remove the mainshaft and parking brake drum from the output flange.
7 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Remove the output flange from the vise. 16. If damaged or leaking, remove the output flange plug from the center of the output flange.
8 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Using 2-3 Jaw Puller D8OL-1O13-A with Bearing Pulling Attachment D79L4621-A and Step Plate D8OL or equivalents, remove the parking brake rear bearing from the mainshaft. 18. Remove the parking brake rear seal from the mainshaft. Discard the seal. 19. NOTE: Insert the tool jaws into the recesses provided in the parking brake housing. Using Bearing Cup Puller T77F A, remove the parking brake rear bearing cup from the parking brake housing. 2O. Turn the parking brake housing over and remove the mainshaft spacer. Remove the O-ring from the spacer. 21. Using Seal Remover TOOL-1175-AC or equivalent, remove the parking brake front seal. Discard the seal. 22. Remove the parking brake front bearing cone from the parking brake housing. 23. NOTE: Position the tool jaws in the recesses provided in the casting.
9 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 9 Using Bearing Cup Puller T77F-1102-A or equivalent, remove the parking brake front bearing cup from the parking brake housing. 24. Remove the four backing plate-to-parking brake housing bolts. 25. NOTE: To aid assembly, observe the orientation of the actuating lever and actuating lever spring. NOTE: Because the parking brake shoes and the backing plate are serviced as a combined unit, they are not disassembled any further. Remove the parking brake shoe and backing plate assembly from the parking brake housing. 26. Remove the splash shield from the parking brake housing.
10 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Remove the actuating lever and the actuating lever spring from the parking brake housing. ransmission-mounted Parking Brake Assembly 1. Using Bearing Cup Replacer T88T-2598-E, install the parking brake rear bearing cup in the parking brake housing.
11 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Position the parking brake rear bearing cone in the parking brake rear bearing cup. 3. NOTE: The lip of the parking brake rear seal should face inward. Using Seal Replacer T58T-2598-C, install a new parking brake rear seal. 4. Turn the parking brake housing over and, using Bearing Cup Replacer T88T-2598-D, install the parking brake front bearing cup.
12 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Using the orientation noted at disassembly, position the actuating lever spring on the parking brake housing. 6. Apply a light coating of Ford Disc Brake Caliper Slide. Grease D7AZ A or equivalent meeting Ford specification ESA-M1C172-A to the ball of the actuating lever. 7. Position the actuating lever ball end through the coil of the actuating lever spring into the mating hole in the parking brake housing. 8. Position the splash shield on the parking brake housing over the actuating lever cam.
13 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Position the parking brake shoe and backing plate assembly on the splash shield. 10. Install the four backing plate-to-housing bolts through the. backing plate and splash shield. Tighten to Nm (87-90 lb-ft). 11. Position the actuating lever spring on the actuating lever to apply tension. 12. CAUTION: Use softjaws to protect the mainshaft.
14 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 14 Mount the mainshaft in a suitable vise with the flange end upward. 13. If necessary, apply sealer and install the output flange plug. Make sure the plug is flush with the output flange bore. 14. Aligning the disassembly match marks, position the parking brake drum and output flange over the mainshaft-to-output flange bolts. 15. Install, but do not tighten, the four 11/16 mainshaft-to-output flange nuts.
15 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Remove the mainshaft, parking brake drum and output flange assembly from the vise and reverse the position so that the vise clamps on the output flange yoke. 17. Tighten the mainshaft-to-output flange nuts to Nm (84-86 lb-ft). 18. CAUTION: Use care not to damage the parking brake rear bearing seal. Carefully guide the parking brake housing over the mainshaft. 19. NOTE: The mainshaft shim determines the mainshaft end play and is available in increments of O.048mm ( inch).
16 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 16 Install the mainshaft shim. 20. Install the parking brake front bearing cone.
17 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Seat the front bearing cone, using Bearing Cone Replacer T88T-2598-F. 22. NOTE: For mainshaft end play measurement, install the mainshaft spacer without the O-ring. Install the mainshaft spacer. 23. Install the lock nut washer. 24. Install a new lock nut and, using 2 9/16-Inch Hex Locknut Wrench T70T4252-D, tighten to Nm ( lb-ft). 25. Remove the parking brake from the vise and position on a smooth flat surface with the output flange down.
18 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Mount Dial Indicator with Bracketry TOOLA2O1-C or equivalent between the mainshaft and the parking brake housing to check end play. 27. While rotating the parking brake housing on the mainshaft to center the bearings, apply pressure up and down while taking an end play reading. A reading of mm ( inches) is required. If the measurement is not within specification, a thinner or thicker shim will be required. 28. Mount the parking brake in a vise, gripping the output flange yoke. 29. Remove the lock nut, lock nut washer and mainshaft spacer from the mainshaft. 30. NOTE: Use care not to lose the mainshaft shim.
19 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 19 If required to install different size mainshaft shim, use 2-3 Jaw Puller D8OL-1013-A or equivalent, to separate the mainshaft, parking brake drum and output flange assembly from the parking brake housing only enough to free the parking brake front bearing cone. 31. If required, remove the parking brake front bearing cone and install the mainshaft shim required to meet end play specification.
20 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page If required, reinstall the parking brake front bearing cone. 33. If required, seat the front bearing cone using Bearing Cone Replacer T88T-2595-F. 34. NOTE: The lip of the parking brake front seal must face inward.
21 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 21 Using Seal Replacer T88T-2598-B, install a new parking brake front seal. 35. Install a new O-ring in the groove of the mainshaft spacer. 36. Install the mainshaft spacer on the mainshaft up to the inner race of the parking brake front bearing.
22 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Install the lock nut washer, the lock nut and, using 2 9/1 6-Inch Hex Locknut Wrench T70T4252-D tighten to Nm ( lbft). 38. Use a hammer and punch to dimple the lock nut flange into the notch on the mainshaft. 39. NOTE: The parking brake vent must be clean and open. Install the parking brake vent. Tighten to Nm (8-12 lb-ft). 40. Remove the parking brake from the vise. 41. Install the parking brake on the vehicle.
23 1997 Ford Truck F 350 2WD Pickup V L VIN G EFI Copyright 2007, ALLDATA 9.50 Page Fill the parking brake to the bottom of the filler hole with Motorcraft MERCON Multi-Purpose Automatic Transmission Fluid, XT-2-QDX or DDX or MERCON equivalent. 43. Install the parking brake filler plug. Tighten to Nm (26-29 lb-ft).
1. Remove the parking brake assembly. 2. Remove the 4 bolts holding the yoke flange and drum. Remove the yoke flange and drive.
Disassembly NOTE: To replace the brake assembly, brake shoe and lining assemblies, or other operational components the complete parking brake assembly must be removed from the vehicle. 1. Remove the parking
1999 F-150/250 Workshop Manual
Page 1 of 30 SECTION 205-03: Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 1999 F-150/250 Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 01/08/2003 Axle Front Drive Special Tool(s)
DISASSEMBLY AND ASSEMBLY
205-03-1 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-1 DISASSEMBLY AND ASSEMBLY Axle Front Drive Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) Special Tool(s) Carrier Bearing Replacer
1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
Page 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint
2001 F-650/750 Workshop Manual
26. Pack the reverse idler gear bearings with lubricant. Use Moly number 2 lubricant or equivalent. 27. Install the following: 1. Assemble the reverse idler gear and bearings onto the idler shaft. 2. Position
DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.
308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing
SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
IN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s)
205-02A-1 IN-VEHICLE REPAIR Differential Bearings Special Tool(s) Protector, Drive Pinion Thread 205-460 Special Tool(s) Installer, Differential Shim 205-220 (T85L-4067-AH) 205-02A-1 2-Jaw Puller 205-D072
Assembly. NOTE: Before beginning assembly, perform/inspect the following:
Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2
DISASSEMBLY AND ASSEMBLY
205-02B-1 DISASSEMBLY AND ASSEMBLY Differential Case and Ring Gear Material Item Specification 205-02B-1 Special Tool(s) Additive Friction Modifier EST-M2C118-A XL-3 2-Jaw Puller 205-D072 (D97L-4221-A)
Page 1 of 6 Axle Shaft, Hub, Oil Seal and Outer Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Locknut Wrench T85T-4252-AH Removal 1. Set the parking brake and loosen the eight
DISASSEMBLY AND ASSEMBLY
211-02-1 Power Steering 211-02-1 DISASSEMBLY AND ASSEMBLY Steering Gear Special Tool(s) Holding Fixture, Transmission 307-003 (T57L-500-B) Special Tool(s) Installer, Worm Bearing Locknut 211-012 (T66P-3553-B)
BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
ASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing
Inspection and Verification, Ranger
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk53a03.htm~gen~ref.htm Page 1 of 1 Section 05-03A: Wheel Hubs and Bearings, Front Wheels, 4- Wheel Drive DIAGNOSIS AND TESTING 1997 Ranger 4x4 with Dana
1995 Town Car/Crown Victoria/Grand Marquis
Page 1 of 23 Section 11-04: Steering Column DISASSEMBLY AND ASSEMBLY 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual Steering Column Disassembly 1. Disconnect battery ground cable (14301)
REMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
SECTION B Manual Transaxle/Transmission TR6060
308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2
SUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - REAR 1988 Toyota Celica REAR SUSPENSION Toyota IRS DESCRIPTION The Toyota Independent Rear Suspension (IRS) system utilizes MacPherson struts, which fasten to axle carrier and wheel housing.
DESCRIPTION AND OPERATION. Description
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk73001.htm~gen~ref.htm Page 1 of 1 Section 07-03: Transmission, Manual, M5OD DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Description The M5OD
Page 1 of 15 Transmission, Model S5-42 ZF Model S5-42 ZF Disassembly NOTE: For 4x4 and F-Super Duty vehicles, skip to Step 5. 1. Attach the transmission to the Bench Mounted Holding Fixture T57L-500-B
2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul
2001-05 AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transaxle installation. Oil cooling system contamination may cause premature transaxle
1997 Thunderbird/Cougar
Page 1 of 7 Section 11-04: Steering Column 1997 Thunderbird/Cougar Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 05/16/2000 Steering Column Disassembly CAUTION: Do not remove the steering
Differential Bearings
SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Bearings Special Tool(s) 2 Jaw Puller
Differential Bearings
SECTION 205-02A: Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 04/02/2009 Differential Bearings Special Tool(s) 2 Jaw Puller
4.2 WATER PUMP (GEAR CASE MOUNTED AND LATER) (GCM)
SERIES 60 SERVICE MANUAL 4.2 WATER PUMP (GEAR CASE MOUNTED - 1991 AND LATER) (GCM) The centrifugal-type water pump circulates the engine coolant through the cooling system. The pump is mounted on the rear
REAR AXLE Click on the applicable bookmark to selected the required model year
REAR AXLE 27-1 REAR AXLE CONTENTS GENERAL INFORMATION.................. 2 SERVICE SPECIFICATIONS................. 3 LUBRICANTS.............................. 3 SEALANTS AND ADHESIVES.............. 4 SPECIAL
Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
BRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE
BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated
DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
2001 Dodge RAM 3500 PICKUP
1 of 76 9/14/2012 7:02 PM 2001 Dodge RAM 3500 PICKUP Submodel: Engine Type: L6 Liters: 5.9 Fuel Delivery: FI Fuel: DIESEL Subarticles MANUAL- NV3500 - DISASSEMBLY MANUAL- NV3500 - DISASSEMBLY MANUAL -
Differential Ring And Pinion
SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Ring And Pinion Special Tool(s) 2 Jaw
MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed
IDENTIFICATION MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED 1998 MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed Transmission has 2 identification labels, located on lower left side of case. One
1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
1997 Explorer/Mountaineer
Page 1 of 9 Section 308-07C: Transfer Case All-Wheel Drive DISASSEMBLY AND ASSEMBLY 1997 Explorer/Mountaineer Workshop Manual Transfer Case Special Service Tool(s) Bearing Cone Replacer T88T-7025-B Bearing
Steering Gearbox Disassembly
Steering Gearbox Disassembly Steering Rack Disassembly 5. Unbend the lock washer. Before disassembling the gearbox, wash it off with solvent and a brush. Do not dip seals and O-rings in solvent. 1. Remove
BRAKE SYSTEM Article Text 1992 Mitsubishi Mirage For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Monday, April 01, :05AM
Article Text ARTICLE BEGINNING 1992 BRAKES Chrysler Motors/Mitsubishi - Disc & Drum Chrysler Motors: Colt, Colt 200, Colt Vista, Ram-50, Stealth, Summit, Summit Wagon; Mitsubishi: Diamante, Eclipse, Expo/Expo
DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1.
2004 SUSPENSION Front - TSX DESCRIPTION NOTE: For system description and component location, see Fig. 1. Fig. 1: Identifying Front Suspension Components Wednesday, March 12, 2008 8:30:45 8:30:55 PM Page
SUZUKI SQ 416/420/625 M.Y TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS
SUZUKI SQ 416/420/625 M.Y 1998-2005 TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS WARNING/CAUTION/NOTE IMPORTANT Please read this manual and follow its instructions carefully.
1993 Bronco/Econoline/F-Series
Page 1 of 7 Section 11-02A: Steering Pump, Power, C-II DISASSEMBLY AND ASSEMBLY Workshop Manual Power Steering Pump NOTE: Prior to disassembly of the power steering pump, the pump must be removed from
12. FRONT WHEEL/FRONT BRAKE/
12 12 12-0 SERVICE INFORMATION... 12-1 FRONT BRAKE... 12-7 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-18 STEERING HANDLEBAR... 12-3 FRONT FORK... 12-21 FRONT WHEEL... 12-4 SERVICE INFORMATION GENERAL
ASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s)
307-01-1 Automatic Transaxle/Transmission 307-01-1 ASSEMBLY Transmission Special Tool(s) Adjustment Set, Transmission Band 307-S022 (T71P-77370-A) Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P-77103-X)
DRIVE AXLE - INTEGRAL HOUSING
DRIVE AXLE - INTEGRAL HOUSING 1993 Toyota Celica 1993 DRIVE AXLES Toyota Differentials & Axle Shafts - Integral Housing Toyota; Celica All-Trac DESCRIPTION Drive axle assembly is a hypoid type with integral
MANUAL TRANSAXLE Return to Main Table of Contents
MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note
Page 1 of 22 SECTION 307-01: Automatic Transaxle/Transmission 4R70E/4R75E ASSEMBLY Procedure revision date: 05/29/2009 Transmission Printable View (1554 KB) Special Tool(s) Air Test Plate, Transmission
MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. ASSEMBLY...24 Gear Components...24
MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
2003 E-Series Workshop Manual
Page 1 of 20 SECTION 307-01B: Automatic Transmission 4R70W 2003 E-Series Workshop Manual ASSEMBLY Procedure revision date: 04/27/2006 Transmission Printable View (1828 KB) Special Tool(s) Dial Indicator
DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I
DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment
If it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
IN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
SPECIAL TOOLS Dodge Pickup 5.9L Eng R3500. Fig 1: Identifying Remover C-3985-B (Special Tool) 9/6/13 Printer Friendly View
Procedures 2003 Dodge Pickup 5.9L Eng R3500 manual transmission SPECIAL TOOLS Fig 1: Identifying Remover C-3985-B (Special Tool) www2.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=
MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. Case Components...27
MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle
204-01 Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014 Axle 1 N620604 Axle pivot nut 2 N806859 Axle pivot bolt 3 3007 LH/ 3006 RH LH/ 3006 RH Axle Removal NOTICE:
DIFFERENTIALS & AXLE SHAFTS
DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,
12. FRONT WHEEL/FRONT BRAKE/
12 4.5kgm 0.9kg-m 4.5kg-m 12-0 SERVICE INFORMATION... 12-1 HYDRAULIC BRAKE... 12-10 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-16 FRONT WHEEL... 12-3 STEERING HANDLEBAR... 12-19 FRONT BRAKE...
Model 4360 Teardown and Reassembly Instructions
Clean the outside surface of the transaxle. Place the shifter in neutral position. Remove detent cover screw (item 3), detent cover (item 4), detent springs (item 5), and detent balls (item 6). Use a magnet
SUSPENSION - FRONT Infiniti G20 DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Front G20
SUSPENSION - FRONT 1992 Infiniti G20 1991-92 SUSPENSION Front G20 DESCRIPTION G20 uses a 4-wheel independent multi-link suspension system. Transverse links are connected to bottom of steering knuckle.
REAR DIFFERENTIAL LOCATION INDEX
2007 DRIVELINE/AXLES Differential - MX-5 Miata REAR DIFFERENTIAL LOCATION INDEX Fig. 1: Identifying Location Of Rear Differential Components DIFFERENTIAL OIL INSPECTION 1. Park the vehicle on level ground
SECTION D Fuel Charging and Controls Turbocharger
303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger... 303-04D-2 303-04D-2 Fuel Charging and Controls Turbocharger
Front Hub and Disc (4WD Model)
4C 8 DRIVE SHAFT SYSTEM Disassembled View Front Hub and Disc (4WD Model) 411RW001 Legend (1) Bolt (2) Cap (3) Snap Ring and Shim (4) Hub Flange (5) Lock Washer and Lock Screw (6) Hub Nut (7) Outer Bearing
2012 Expedition, Navigator Workshop Manual
Item Part Number Description 1 W720586 Differential housing cover bolt (12 required) 2 4033 Differential housing cover 3 Differential bearing cap bolts (part of 4010) (4 required) 4 Differential bearing
SECTION TF CONTENTS TRANSFER IDX
TRANSFER SECTION TF GI MA EM LC PREPARATION...2 Special Service Tools...2 Commercial Service Tools...3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...4 NVH Troubleshooting Chart...4 Transfer...4
TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.
TRANSMISSION 6.7 GENERAL See Figure 6-46. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. b06x6x Neutral st Gear Mainshaft Mainshaft 4 5 4 5 Countershaft Out
This file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION AXLE SHAFTS & BEARINGS Removal CAUTION: Failure to turn off air suspension power before raising vehicle may result in unexpected inflation or deflation of air springs. DO NOT reconnect
Reverse Idler Gear Shaft
«1993 Thunderbird/Cougar Table of Contents» «Group 07: TRANSMISSION» «Section 07-03: Transmission, Manual--M5R2» «DISASSEMBLY AND ASSEMBLY» Reverse Idler Gear Shaft Disassembly Remove the following parts
SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS
SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS General Description and Operation... 5B-2 Shift Lever... 5B-2 Transmission Assembly... 5B-2 Specifications... 5B-3 Diagnostic Information and Procedures...
FRONT AXLE Click on the applicable bookmark to selected the required model year. Purchased from
FRONT AXLE Click on the applicable bookmark to selected the required model year. 26-1 FRONT AXLE CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 4 LUBRICANTS... 4 SEALANTS... 5 SPECIAL TOOLS...
PROPELLER SHAFT & DIFFERENTIAL CARRIER SECTIONPD CONTENTS IDX. PROPELLER SHAFT...3 Preparation...3 C200. REAR FINAL DRIVE...40 Preparation...
PROPELLER SHAFT & DIFFERENTIAL CARRIER SECTIONPD GI MA EM LC EC CONTENTS FE PROPELLER SHAFT...3 Preparation...3 SPECIAL SERVICE TOOLS...3 Noise, Vibration and Harshness (NVH) Troubleshooting...4 NVH TROUBLESHOOTING
Service Manual. #19 Gearmatic Winch
Allis Chalmers Service Manual #19 Gearmatic Winch Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF ALLIS CHALMERS OR IT S SUCCESSORS. ALLIS CHALMERS AND IT S SUCCESSORS
Steering Gear: Service and Repair POWER STEERING GEAR BOX
2003 Kia Truck Sorento V6-3.5L Copyright 2013, ALLDATA 10.52 Page 1 Steering Gear: Service and Repair POWER STEERING GEAR BOX COMPONENTS REMOVAL 1. Drain the power steering fluid. 2. Disconnect the pressure
M Ring and Pinion Installation
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. Axle Shaft Removal (1994-2012 Mustang typical) STEP 1: STEP 2: Remove the 10 differential housing cover bolts and drain
BRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
Installation Instructions for the Tera low range Dana 20 (LOW20)
Installation Instructions for the Tera low range Dana 20 (LOW20) Tera Manufacturing, Inc. 5251 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.288.2571 www.teraflex.biz Attention: Verify
POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly
POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly DISASSEMBLY: 1. Remove pump from car and allow to drain. 2. Remove pulley from front of pump. This requires
Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.
«1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept
TRANSMISSION AND TRANSFER CASE
DR TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page MANUAL TRANSMISSION- G56- SERVICE INFORMATION...1 MANUAL TRANSMISSION- GETRAG 238- SERVICEINFORMATION...69 MANUAL
TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.
TRANSMISSION 6.7 GENERAL See Figure 6-45. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. Mainshaft Neutral Mainshaft st Gear b06x6x Countershaft 4 Out 5 Countershaft
COLT 2310, 2510, AND 2712 COM PACT TRACTORS CHAPTER 7 BEARINGS, SEALS, GASKETS
COLT 2310, 2510, AND 2712 COM PACT TRACTORS CHAPTER 7 BEARINGS, SEALS, GASKETS END PLAY SEE SPECIFICATIONS "A" SHIM C" GASKET "B" STEEL WASHER IF REQUIRED 7-A-l Figure 7-A-l illustrates the correct assembly
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CENTER BEARING SUPPORT ASSEMBLY Removal 1. With transmission in neutral and parking brake off, raise vehicle. Scribe alignment marks on all flange/yokes and slip joints to be disassembled
MANUAL TRANSMISSION SECTION MT CONTENTS TRANSMISSION/TRANSAXLE MT-1 SERVICE INFORMATION POSITION SWITCH...13 Checking...13
TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Service Notice or Precaution...2 PREPARATION... 3 Special Service Tool...3 Commercial
TRANSFER SECTIONTF CONTENTS IDX
TRANSFER SECTIONTF GI MA EM LC EC CONTENTS FE PREPARATION...2 Special Service Tools...2 Commercial Service Tools...3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...5 NVH Troubleshooting Chart...5
DISASSEMBLY AND ASSEMBLY
307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,
INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks
INSTRUCTIONS Disassembly To protect against accidental start-up of vehicle, always disconnect the negative battery cable before working on the motorcycle. Failure to disconnect the battery cable could
SECTION Front Drive Axle/Differential
205-03-i Front Drive Axle/Differential 205-03-i SECTION 205-03 Front Drive Axle/Differential CONTENTS PAGE Axle... 205-03-2 205-03-2 Front Drive Axle/Differential 205-03-2 Axle Special Tool(s) C-Frame
Steering Column. Disassembly. 1. Remove instrument panel cover and reinforcement from vehicle as described in this section.
Page 1 of 14 Section 11-04A: Steering Column, Ranger 1997 Aerostar/Ranger Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 05/17/2000 Steering Column Disassembly 1. Remove instrument panel
Mustang Differential Gears - Installation Instructions
Mustang Differential Gears - Installation Instructions The below installation instructions work for the following products: Ford Racing Gears - 3.73 Gears for 8.8" Ford Rear End Ford Racing Gears - FRPP
TRANSFER SECTIONTF CONTENTS IDX EXIT. Counter Gear...20
TRANSFER SECTIONTF GI MA EM LC EC CONTENTS FE CL PREPARATION...2 Special Service Tools...2 Commercial Service Tools...3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...5 NVH Troubleshooting Chart...5
Brake Shoe: Service and Repair Removal Procedure
2000 Buick Century V6-3.1L VIN J Copyright 2013, ALLDATA 10.52 Page 1 Brake Shoe: Service and Repair Removal Procedure ^ Tools Required - J38400 Brake Shoe Spanner and Spring Remover Caution: Keep fingers
M-4851-M8A SUPER 8.8 IRS MUSTANG AUTOMATIC PINION FLANGE KIT
Please visit fordperformanceracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
Gear Products Inc N. 161st E. Ave. Tulsa, OK Phone (918) Fax (918)
SERVICE MANUAL Disassembly & Assembly Procedures Worm Gear Swing Drive 003 Series Gear Products Inc. 1111 N. 161st E. Ave. Tulsa, OK 74116 Phone (918) 234-3044 Fax (918) 234-3455 Worm Gear Swing Drive
1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
MANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34
MANUAL TRANSAXLE SECTIONMT GI MA EM LC EC CONTENTS FE PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
Transmission Overhaul Procedures-Bench Service
How to Install the Auxiliary Countershaft Assembly Special Instructions To make auxiliary section assembly easier, you can make an auxiliary section fixture out of a 2" x 12" piece of wood. 3' 1' 3" 4.56"
Transmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
LoMax 205 CASE & 3:1 GEAR SET. Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case
LoMax 205 CASE & 3:1 GEAR SET Part No. 2800 Instruction Rev: 2007.08.16 Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case Kit Components: 1. (1) 42x25