FHP s EnviroSaver the best investment for your environment and home.

Transcription

1 EnviroSaver The two-stage EnviroSaver from FHP provides you with a unit that will suit your budget while incorporating innovative technology for reduced energy costs. FHP was the industry leader in introducing ozone friendly refrigerants into our product line. The EnviroSaver with Copeland s UltraTech two stage scroll compressor and an ECM blower motor represents another first for FHP. Specifically designed for Geothermal applications, the EnviroSaver uses the earth's energy to heat and cool your home with savings of up to 60% on your utility bills when compared to conventional systems. You want the very best for your home and the environment. FHP s two stage EnviroSaver Series will provide a unit to meet your expectations.

2 FHP S TWO STAGE EnviroSaver goes beyond industry standards to bring you our highest efficiency unit together with the benefits of the new generation of environmentally friendly refrigerant. A heat pump operates at full load conditions less than 60 percent of the time so it is only logical to have a unit that can match this load profile. The EnviroSaver features Copeland s UltraTech Two Stage Unloading Scroll Compressor which, when controlled by a multistage thermostat, stages the compressor to match the actual demand for heating and cooling. The result lower energy bills, increased comfort and better humidity control. ADVANCED TECHNOLOGY Copeland s UltraTech unloading compressors take scroll technology to the next level while preserving the simplicity in design and reliability of a scroll compressor. In addition to the UltraTech scroll compressor the EnviroSaver is equipped with an ECM (Electronically Commutated Motor) fan motor. This motor is factory programmed to vary the airflow based on the stages of compressor operation resulting in additional energy savings and a greater level of comfort in the living space. What this means to you are lower electric utility bills for heating and cooling. GEOTHERMAL READY All FHP EnviroSaver units come ready for operation in a geothermal application. Using the earth s energy to heat and cool your home is not only good for the environment but can result in savings of 60 percent or more over conventional heating and cooling systems. Increase your energy savings with an internally mounted heat recovery system providing much of your hot water needs at virtually no additional operating costs. QUIET OPERATION ECM fan motors and the UltraTech s compressor s remarkably quiet operation, up to four times quieter than a comparable reciprocating compressor, combine to give you a unit with truly whisper quiet operation. ENVIRONMENTALLY FRIENDLY Refrigerant R-410A, the industries choice as a replacement for refrigerant R-22, preserves the earth s fragile ozone layer and assures you of availability of supply for the life of the unit. Geothermal operation contributes to a cleaner environment without the need for an unsightly outside unit. Do not be caught with high service charges once refrigerant R-22 has been phased out and is in short supply. FHP QUALITY Electro coated evaporator coils together with a Galvalume Plus finish and FHP s thirty years experience are your assurance of a quality product. FHP s EnviroSaver the best investment for your environment and home. FHP Manufacturing Company 601 NW 65th Court Fort Lauderdale, FL

3 ES SERIES TWO STAGE heat pumps O ur two stage EnviroSaver Series goes beyond industry standards to bring you high efficiency together with the benefits of the new generation of environmentally friendly refrigerants. A heat pump operates at full load conditions less than 60 percent of the time so its only logical to have a unit that can match the load profile. FHP s EnviroSaver features Copeland s UltraTech Two Stage Unloading Scroll Compressor which, when controlled by a multistage thermostat, stages the compressor to match the demand for heating and cooling. The result: lower energy bills, increased comfort and better humidity control. In addition to the UltraTech Scroll Compressor, the EnviroSaver is equipped with an ECM (Electronically Commutated Motor) fan motor. This motor is factory programmed to vary the airflow based on the stages of compressor operation resulting in additional energy savings and a greater level of comfort in the living space. Both the UltraTech Scroll Compressor and ECM fan motor have been engineered for reduced sound making this the quietest unit on the market today. All FHP EnviroSaver units come ready for operation in a geothermal application. Geothermal installations are the most cost-effective and energy efficient heating and cooling systems available today. Increase your energy savings with an internally mounted heat recovery system providing much of your hot water needs at virtually no additional operating cost. Cost Effective Up to 60% savings are possible using FHP s ES EnviroSaver Series in a geothermal application. Additional investment costs are more than offset when energy costs savings are considered. The system s long life and low maintenance help reduce the overall life cycle costs. Environmentally Friendly FHP is the industry leader in the development of the environmentally friendly technology that is designed into the EnviroSaver Series. Using Refrigerant R-410A gives you protection from potentially skyrocketing maintenance costs associated with obsolete refrigerants. FHP Quality and Reliability FHP s EnviroSaver Series feature coated evaporator coils and stainless steel drain pans as standard to ensure long trouble free life of the units. Rigorous factory testing of each unit ensures trouble free operation from the start while FHP s thirty years of experience in heat pumps are your assurance of a state of the art quality product. ISO 9001:2000 Certified

4 ES SERIES TWO STAGE HORIZONTAL VERTICAL COUNTERFLOW DIMENSIONS VERTICAL/C. FLOW HORIZONTAL MODEL WIDTH DEPTH HEIGHT WIDTH LENGTH HEIGHT A B C D E F ES025, ES ES ES All ratings & specifications are subject to change without notice. ARI / ISO PERFORMANCE DATA ENTERING WATER TEMPERATURES Water Loop Ground Loop Ground Water MODEL CFM 86 F 68 F 77 F 32 F 59 F 50 F CAPACITY AND EFFICIENCY DATA COOLING COOLING COOLING CAPACITY EER CAPACITY COP CAPACITY EER CAPACITY COP CAPACITY EER CAPACITY COP (WLHP) (WLHP) (WLHP) (WLHP) (GLHP) (GLHP) (GLHP) (GLHP) (GWHP) (GWHP) (GWHP) (GWHP) ES025 Part Load , , , , , , Full Load , , , , , , ES035 Part Load , , , , , , Full Load , , , , , , ES049 Part Load , , , , , , Full Load , , , , , , ES061 Part Load , , , , , , Full Load , , , , , , ES071 Part Load , , , , , , Full Load , , , , , , Tabulated performance data is at noted entering water temperatures and entering air conditions of 80.6 F DB/66.2 F WB at ARI/ISO rated CFM ENERGY STAR RATED 601 N.W. 65TH COURT FT. LAUDERDALE, FL PHONE: (954) FAX: (800) heat pumps Rev. 11/08

5 GUIDE SPECIFICATIONS ES Series Two Stage R-410A GENERAL Units shall be performance certified to ISO standard for Water Loop Pump, Ground Water Pump and Ground Loop Pump applications. Units shall be Underwriter Laboratories (UL and ULc) listed for safety on all models. Each unit shall be run tested at the factory. Each unit shall be pallet mounted and stretch wrapped. The units shall be manufactured in an ISO9001:2000 certified facility. The units shall be warranted by the manufacturer against defects in materials and workmanship for a period of i) in the case of residentially sold units having the last digit of the serial number as a 'T'; five years on all parts and 10 years on the refrigerant circuit components ii) on all other units; five years on the compressor and one year on all other parts. The units shall be designed to operate with entering fluid temperatures between 50 F (10 C) and 110 F (43.3 C) in cooling and temperatures between 25 F (-3.9 C) and 80oF (27 C) in heating as manufactured by FHP Manufacturing in Fort Lauderdale, Florida. CASING & CABINET The cabinet shall be fabricated from heavy-gauge steel finished with Galvalume plus, an aluminum-zinc alloy with a clear acrylic coating for additional corrosion protection. The interior shall be insulated with ½ (12.7mm) thick, multi density, coated, glass fiber. All units shall allow sufficient service access to replace the compressor without unit removal. One blower and two compressor compartment access panels shall be removable with supply and return ductwork in place. A duct collar shall be provided on the supply air opening. A filter rack with 1" (25.4mm) thick disposable filters and a 1" (25.4mm) return air duct collar shall be provided with each unit. The units shall have an insulated divider panel between the air handling section and the compressor section to minimize the transmission of compressor noise, and to permit service testing without air bypass. Units shall have a stainless steel condensate drain pan. REFRIGERATION CIRCUITS All units shall contain a sealed refrigerant circuit including a hermetic two stage scroll compressor, bi-directional thermal expansion valve metering device, finned tube air-to-refrigerant heat exchanger, refrigerant reversing valve and service ports. Compressor shall be high efficiency scroll type, designed for heat pump duty, quiet operation and mounted on rubber vibration isolators. Compressor motors shall be equipped with overload protection. Refrigerant reversing valves shall be pilot operated sliding piston type with replaceable encapsulated magnetic coils energized only during the cooling cycle. The finned tube coil shall be constructed of lanced aluminum fins not exceeding fourteen fins per inch bonded to rifled copper tubes in a staggered pattern not less than three rows deep and have a 450 PSIG (3100 kpa) working pressure. Coils shall have a baked polyester enamel coating for protection against most airborne chemicals. Coil end plates shall be aluminum. The coaxial water-to-refrigerant heat exchanger shall be constructed of a convoluted copper (optional cupronickel) inner tube and steel outer tube with a designed refrigerant working pressure of 450 PSIG (3100 kpa) and a designed water side working pressure of no less than 400 PSIG (2750 kpa). The water-to-refrigerant heat exchanger shall be insulated to prevent condensation at low fluid temperatures. FAN MOTOR & ASSEMBLY The fan shall be direct drive centrifugal forward curved type with a dynamically balanced wheel. The housing and wheel shall be designed for quiet low velocity operation. The fan housing shall be removable from the unit without disconnecting the supply air ductwork for servicing of the fan motor. The fan motor shall be an ECM-2 microprocessor controlled DC type motor with internal programming factory set for the specific unit and featuring soft start/stop and a delay off feature for maximum efficiency and quiet operation. Air flow rates shall be varied according to the staging of the unit. There will further be provisions for adjusting the air delivery of the motor and blower by +/- 15% from rated air flow. ELECTRICAL Controls and safety devices will be factory wired and mounted within the unit. Controls shall include compressor contactor, 24V transformer, reversing valve coil and solid state lock-out controller (UPM). The UPM controller shall include the following features: diagnostic LED's, low pressure bypass time delay (to prevent nuisance low pressure lockouts during operation with low fluid temperatures), anti short cycle time delay, random start time delay and one time intelligent reset. When the safety controls are activated the lock-out circuit shall reset itself the first time. If the safety controls are subsequently activated, then the lock-out circuit shall disable the compressor until it is reset at the thermostat or main circuit breaker to prevent compressor operation during fault conditions. A lock-out indicating terminal shall be provided in the low voltage circuit. Safety devices include a low pressure cutout set a 40 PSIG (280 kpa) for loss of charge protection (freezestat and/ or high discharge gas temperature sensor is not acceptable) and a high pressure cutout control set at 600 PSIG (4100 kpa). The ECM motor interface board shall provide a screw type terminal block for thermostat connection, LED's to indicate thermostat status and air delivery. It shall also provide a means of changing the motor program to any of up to four pre-programmed options. Direct wiring of the motor control harness to the thermostat is not acceptable. A terminal block with screw terminals shall be provided for control wiring. An optional condensate overflow device shall be factory installed to stop compressor operation if drain pan overflow is imminent. An optional energy management relay to allow unit control by an external source shall be factory installed. PIPING Supply, return water and condensate drain connections shall be brass female pipe thread fittings and mounted flush to cabinet exterior. INTERNAL ELECTRIC HEAT 208/ volt units shall be equipped with optional factory installed internal electric resistance heat for auxiliary and emergency heat. Electric heater must be Underwriter's Laboratories (UL and ULc) approved for safety when installed in the unit. External heater packages or heater packages not specifically listed for use with the unit are unacceptable. Electric heater packages shall include a heater collar mounted to the blower outlet, individual thermal overload protected heater elements no greater than 5kW each and magnetic contactors. er packages shall have a separate power supply connection from the compressor and this power supply shall also power the unit blower motor and control transformer for safe operation. HEAT RECOVERY PACKAGE 208/230 volt units shall be equipped with a optional factory installed internal heat recovery kit for domestic hot water production. This kit shall include an internally protected pump, double walled coaxial waterto-refrigerant heat exchanger, 140 F (60 C) hot water temperature limit switch and an on/off switch/circuit breaker. LOOP PUMP PACKAGE - CONSULT FACTORY 208/ volt units shall be equipped with an optional factory installed ground loop pump kit. This kit shall include a 1/6 HP loop pump, isolation valves and a set of purge connections for purging and pressurizing the ground loop with the unit in place. The pump, all piping and valves shall be internal to the unit. ESSPECS.INDD REV: 10-06

6 FHP Manufacturing Co. 601 N.W. 65th Court Fort Lauderdale, FL Phone: (954) Fax: (800) ES Two Stage Series Vertical Dimensions A B C D E F G H J K M N P Q Condenser Recommended MODEL R/A Duct R/A Duct Filter Rack Water Replacement Width Depth Height Flg Width Flg Height Height Connections Nominal Filter Size ES025, /4" F.P.T. 24 X 24 X 1 ES " F.P.T. 24 X 30 X 1 ES " F.P.T. 24 X 30 X 1 ES " F.P.T. 16 X 30 X 1 (2) Left Hand Return ESVTDGIP INT II.P65 REV: Right Hand Return (FRT) (FLT) NOTES: All dimensions within +/ ". All condensate drain connections are 3/4" FPT. All Recovery Kit connections are 1/2" FPT. Internal electric heat available on /1/60 top discharge units only Internal Recovery Kit available on volt units only. Specifications subject to change without notice.

7 FHP Manufacturing Co. 601 N.W. 65th Court Fort Lauderdale, FL Phone: (954) Fax: (800) ES Two Stage Series Horizontal Dimensions A B C D E F G H J K M N P Q R T Condenser Recommended MODEL R/A Duct Filter Rack R/A Duct Water Replacement Width Depth Height Flg Width Height Flg Height Connections Nom. Filter Size ES025, /4" F.P.T. 18 X 30 X 1 (1) ES " F.P.T. 18 X 20 X 1 (2) ES " F.P.T. 18 X 20 X 1 (2) ES " F.P.T. 20x24x1 (2) Left Hand Return End Blow (FLE) Left Hand Return Straight Through (FLS) Left Hand Return Right Hand Return Right Hand Return End Blow (FRE) Right Hand Return Straight Through (FRS) NOTES: All dimensions within +/ ". All condensate drain connections are 3/4" FPT. All Recovery connections are 1/2" FPT. Internal electric heat available on volt units only Internal Recovery Kit available on volt units only. Units can be field converted between end blow and straight through supply air configurations. Specifications subject to change without notice. EVHZDGIP.P65 REV: 6-07

8 FHP Manufacturing Co. 601 N.W. 65th Court Fort Lauderdale, FL Phone: (954) Fax: (800) ES Two Stage Series Counterflow Dimensions A B C D E F G H J K M N P Condenser Recommended MODEL R/A Duct R/A Duct Filter Rack Water Replacement Width Depth Height Opening Opening Flg Width Flg Height Height Connections Nominal Filter Size ES025, /4" F.P.T. 24 X 24 X 1 ES " F.P.T. 24 X 30 X 1 ES " F.P.T. 24 X 30 X 1 ES " F.P.T. 16 X 30 X 1 (2) ESCFDGIP INT II.P65 REV: Left Hand Return (FLB) Right Hand Return (FRB) NOTES: All dimensions within +/ ". All condensate drain connections are 3/4" FPT. All Recovery Kit connections are 1/2" FPT. Internal electric heat available on /1/60 bottom discharge units only Internal Recovery Kit available on volt units only. Specifications subject to change without notice.

9 Electrical Elect. Compressor Loop Pump Min. Max. 208/ / Norm ISO CERTIFIED PERFORMANCE DATA Rated at 500 CFM and 6.0 GPM Cooling ing Cooling ing Cooling ing 18, , , , , , CAPACITY DATA - PART LOAD COOLING All performance at 500 CFM and 6.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES025.1IP60 Rev: 9-05 F to F 30 o 30 o 30 o ES / x 7 DD Scroll 290 lbs 315 lbs

10 Electrical Elect. Compressor Loop Pump Min. Max. 208/ / Norm ISO CERTIFIED PERFORMANCE DATA Rated at 800 CFM and 6.0 GPM Cooling ing Cooling ing Cooling ing 26, , , , , , CAPACITY DATA - FULL LOAD COOLING All performance at 800 CFM and 6.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES025.2IP60 Rev: 9-05 F to F 30 o 30 o 30 o ES / x 7 DD Scroll 290 lbs 315 lbs

11 Electrical Elect. Compressor Loop Pump Min. Max. 208/ / / / / Note: 460 Volt Units (-4) Require Both Ground and Neutral Wires Norm 800 ISO CERTIFIED PERFORMANCE DATA Rated at 800 CFM and 9.0 GPM Cooling ing Cooling ing Cooling ing 24, , , , , , CAPACITY DATA - PART LOAD COOLING All performance at 800 CFM and 9.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES035.1IP60 Rev: / x 7 DD Scroll 290 lbs 315 lbs F to F 30 o 30 o 30 o ES

12 Electrical Elect. Compressor Loop Pump Min. Max. 208/ / / / / Note: 460 Volt Units (-4) Require Both Ground and Neutral Wires Norm ISO CERTIFIED PERFORMANCE DATA Rated at 1200 CFM and 9.0 GPM Cooling ing Cooling ing Cooling ing 36, , , , , , CAPACITY DATA - FULL LOAD COOLING All performance at 1200 CFM and 9.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES035.2IP60 Rev: o 30 o 30 o F to F ES / x 7 DD Scroll 290 lbs 315 lbs

13 Electrical Elect. Compressor Loop Pump Min. Max. 208/ / / / / Note: 460 Volt Units (-4) Require Both Ground and Neutral Wires Norm ISO CERTIFIED PERFORMANCE DATA Rated at 1000 CFM and 12.0 GPM Cooling ing Cooling ing Cooling ing 34, , , , , , CAPACITY DATA - PART LOAD COOLING All performance at 1000 CFM and 12.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES049.1IP60 Rev: o 30 o 30 o F to F ES / x 8 DD Scroll 318 lbs 348 lbs

14 Electrical Elect. Compressor Loop Pump Min. Max. 208/ / / / / Note: 460 Volt Units (-4) Require Both Ground and Neutral Wires Norm ISO CERTIFIED PERFORMANCE DATA Rated at 1600 CFM and 12.0 GPM Cooling ing Cooling ing Cooling ing 48, , , , , , CAPACITY DATA - FULL LOAD COOLING All performance at 1600 CFM and 12.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES049.2IP60 Rev: F to F / x 8 DD Scroll 318 lbs 348 lbs o 30 o 30 o ES

15 Electrical Elect. Compressor Loop Pump Min. Max. 208/ / / / / Note: 460 Volt Units (-4) Require Both Ground and Neutral Wires Norm ISO CERTIFIED PERFORMANCE DATA Rated at 1400 CFM and 14.0 GPM Cooling ing Cooling ing Cooling ing 42, , , , , , CAPACITY DATA - PART LOAD COOLING All performance at 1400 CFM and 14.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES061.1IP60 Rev: o 30 o 30 o F to F ES / x 9 DD Scroll 390 lbs 415 lbs

16 Electrical Elect. Compressor Loop Pump Min. Max. 208/ / / / / Note: 460 Volt Units (-4) Require Both Ground and Neutral Wires Norm ISO CERTIFIED PERFORMANCE DATA Rated at 2000 CFM and 14.0 GPM Cooling ing Cooling ing Cooling ing 60, , , , , , CAPACITY DATA - FULL LOAD COOLING All performance at 2000 CFM and 14.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES061.2IP60 Rev: o 30 o 30 o F to F ES / x 9 DD Scroll 390 lbs 415 lbs

17 Electrical Elect. Compressor Loop Pump Min. Max. 208/ Norm ISO CERTIFIED PERFORMANCE DATA Rated at 1400 CFM and 18.0 GPM Cooling ing Cooling ing Cooling ing 51, , , , , , CAPACITY DATA - PART LOAD COOLING All performance at 1400 CFM and 18.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage. For conditions other than rated, consult the FHP EAD ES071.1IP60 Rev: o 30 o 30 o F to F ES / x 9 DD Scroll 450 lbs 495 lbs

18 Electrical Elect. Compressor Loop Pump Min. Max. 208/ Norm ISO CERTIFIED PERFORMANCE DATA Rated at 2200 CFM and 18.0 GPM Cooling ing Cooling ing Cooling ing 72, , , , , , CAPACITY DATA - FULL LOAD COOLING All performance at 2200 CFM and 18.0 GPM Sensible db 61 o wb 75 o db 63 o wb db 67 o wb db 71 o wb F to F protection and magnetic contactors (208/230-1-nly) optional UL approved internal Recovery Package and/or Ground Performance based on ARI/ISO rated air flow, fluid flow and voltage.for conditions other than rated, consult the FHP EAD ES071.2IP60 Rev: o 30 o 30 o F to F ES / x 9 DD Scroll 450 lbs 495 lbs