Corolla Verso. Swivel seat Installation Instructions. Model Year: Part Number: LHD RHD

Transcription

1 Corolla Verso Swivel seat Installation Instructions PICTURE HERE Model Year: 2004 Part Number: LHD RHD Weight: Installation Time: 28,7 kg 135 minutes Manual reference number AIM

2 Take off the Box CAUTION!! Do not move on the floor Do not put on the floor directly All pictures mentioned on this I/M are for LHD vehicle. 1 of 17

3 E F G H I J 1 C7120-D1500 Check all parts before installation. Parts List for Corolla Verso(LHD) France Only Part Number Parts Part Number Parts A 1 K 1 C7012-D1550 C7120-D B 1 L D1060 C7126-D C 1 M D1060 C D 1 N D S14 L27.5 S14 L S14 L O D1060 P D D D1085 Q D Picture No. S14 L23 French English 2 of 17

4 R 1 C7120-D1490 Check all parts before installation. Parts List for Corolla Verso(RHD) Part Number Parts Part Number Parts A 1 K 1 C7012-D1540 C7120-D B 1 L D1060 C7125-D1A C 1 M D1100 C D 1 N D S14 L27.5 E 9 O D P D1020 S14 L55 F D S14 L28 G 4 S D H 1 T I 1 U V D UK Only S14 L23 S12 S14 L22 3 of 17

5 Tools PROTECTION COVER 1 2 CAUTION!! 3 4 of 17

6 Remove the OE Seat 5 Bolts Seat Bolt Removal Remove the Headrest Bolt Bolt 10 Bolt 11 2 Bolts Bolt of 17

7 Seat Disassembly Some Parts are reused Installation screws (screw) 2 (screw) 15 T= of 17

8 Buckle Bracket Removal Move the Seat Rail forward and backward. (2 of torx bolts removal) T=40 Handling Wire Harness of Buckle Switch 1 Remove the clamp Fix the Wire Harness to the underside of Seat. 7 of 17

9 * Drill the center dent of r v t head with drill. Use the drill φ6 and φ9 beforeφ *Remov the bush with driver. φ13 φ φ13 φ Throw the OE Slide Rail away of 17

10 Assemble the Swivel Seat 41 Note Adjust the hight of seat cushion with vertical height adjuster. Height to : mm be kept A route wiring harness connect 9 of 17

11 45 Buckle Installation I 42 H M Tap hole Wave washer Flat washer Seat belt Buckle Switch G D Bolt Insert the Plate 48 G 49 G G T=30 10 of 17

12 Left Shroud Cover Installation C T= L Seat Anchorage Installation E 2 Bolts 11 of 17

13 J 62 France Only E 5 Bolts K connect Seat Unit Installation * Two technitian is required to install into the vehicle. F Long bolt E 2 bolts E E 12 of 17

14 YAW - RATE SENSOR BRACKET CHANGE (RHD) UK Only E 3 Bolts 2 Nuts T 21 R Anchorage Bracket OEM Brackets 6.0 S YAW RATE SENSOR Installation 70 E 2 Bolts K Cut 1. Cut in Floor Carpet. (Part of the thick line) 2. Tear off urethane inside of carpet. (Inside of the broken line) 3. Remove the Yaw rate sensor from the OEM Bracket. 4. Install Yaw rate sensor on Bracket S with the nuts removed at Install Yaw rate sensor Bracket on Anchorage Bracket with 2 nuts. 13 of 17

15 UK Only connect Seat Unit Installation * Two technitian is required to install into the vehicle F Long bolt T 2 Bolts Short bolts E E 14 of 17

16 78 O 1 Stick the caution label Put the protection seal. N 80 B 3 Stick PART (Carpet, front floor side) on the side wall of Console Box. Note Before sticking the carpet, remove oil from the surface of Console Box Stick the Caution Label on the door trim. (passenger side) P Please make sure the Unit swivels properly after finishing installation. * Check if the "Warning Lamp" for airbag and seat belt on Indicator is turned-off after Engin starting 15 of 17

17 Label putting position (CRS) Put CRS Q staickers as below. For France Only 82 Put on Side of Instrument Panel Q Two places Put the label on O/M of base Vehicle. O/M 16 of 17

18 Label putting position (CRS) Put CRS V staickers as below. For UK Only 83 Put on Side of Instrument Panel V Two places Put the label on O/M of base Vehicle. OM 17 of 17

19 Toyota Motor Europe NV/SA Bourgetlaan 60 B-1140 Brussels Installation checksheet Version date: 15/09/2006 Corolla Verso R1 Mobility project : swivel seats Operator: Date: VIN: Before installation Box content OK Serial number Lift Up seat Supervisor check: During installation VSC ECU and sensor do not interfer with swivel seat Earth connection firmly fitted Foam around connectors B+ terminal in fuse box has proper connection RHD Seat / headrest Don't squeeze wires Don't damage connectors during handling Front seat bolts on torque 37Nm After installation Dashboard All parts installed according to manual Seat (rail) covers well fitted L R SRS warning light comes on when turning key to 'ON' position SRS warning light goes off after approximately 6 seconds Passenger detection light working Wiring under seats strapped to original wiring Warning lights Inspect no damage on the covers / fabric L R Seat heaters working Plastic covers are well fitted? Tune, seek radio Stickers well fitted? Volume up and down (from steering wheel) Correct position comes on the screen automatically (after satellite reception, Arm and foot rest working ok? with full map navi) Console is well aligned with dashboard, Front rear movement is OK? no gaps Cigarette lighter operating Swivel movement is OK? Cigarette lighter illumination Force for operating swivel lever is OK? Audio illumination Electric Mirror working No traces of wiring No NVH while driving? No scratches on dash board VSC signal goes off System (seat operation) Back side Front seats General Wiring under seats leaves enough room for movements, no obstruction when moving forward/backward, up/down. No interference with swivel operation L R