Installation instructions, accessories. Multimedia monitor with DVD, Dual screen. Multimedia monitor with DVD, Dual screen V1.

Size: px

Start display at page:

Download "Installation instructions, accessories. Multimedia monitor with DVD, Dual screen. Multimedia monitor with DVD, Dual screen V1."

Scarlett Garrett
6 years ago
Views:

1 Installation instructions, accessories Instruction No Version Part. No Multimedia monitor with DVD, Dual screen Volvo Car Corporation Multimedia monitor with DVD, Dual screen V1.2 Page 1 / 55

2 Equipment IMG A IMG IMG IMG IMG Page 2 / 55

3 IMG Page 3 / 55

4 IMG Page 4 / 55

5 IMG Page 5 / 55

6 INTRODUCTION Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer. Note! There are two versions of cable harness for the tunnel console, with or without preparations for Digital TV receivers. The images in the installation instructions show cable harness without Digital TV receiver. 1 Slide both the front seats all the way back and upwards all the way at the front and rear edge. Press the headrest downwards. Find the headrest's two locks on the back of the seat. Press in the catches and pull the headrest upwards at the same time. The seats may require lowering slightly at the rear edge again so that the headrest can be pulled out of the backrest completely. Therefore lower the seat as much as possible so that the headrest can be released and removed. Remove the headrest on both front seats and allow the seats to remain in the same position. IMG Page 6 / 55

R8504225 3 Remove the sound barrier on the driver's

7 2 Remove both the side panels from the tunnel console. R Remove the sound barrier on the driver's side by first removing the two screws and then prizing it away at the top edge. R Page 7 / 55

8 4 Pull the handle (1), move the tunnel compartment backward and lift it away (2). IMG Remove the cover. It shall not be re-used. R Page 8 / 55

Use a weatherstrip and pry off the gear selector panel at the rear edge.

9 6 Applies to cars with automatic gearbox Turn the ignition key to position II. Applies to all models Move the gear selector lever to its rearmost position. Use a weatherstrip and pry off the gear selector panel at the rear edge. R Turn the ignition key to position 0. Note! Wait at least three minutes before unplugging the connectors or removing other electrical equipment. IMG Page 9 / 55

10 8 Press in the catches underneath and remove the panel. IMG Remove the small storage compartment. IMG Page 10 / 55

Release the telephone cable. Remove the handset. Remove the screw (3).

11 10 Applies to cars with telephone Unhook and disconnect the connector (1). Disconnect the telephone cable from the load-removing grommet (2). Release the telephone cable. Remove the handset. Remove the screw (3). Push the catch to one side (4). Remove the telephone cradle. R Applies to all models Remove the six screws. IMG Page 11 / 55

socket. IMG-268405 13 Disconnect the connector.

12 12 Lift up and remove the upper section. At the same time disconnect the connector to the AUX socket. IMG Disconnect the connector. Press in the catches and unhook it from the tunnel console. IMG Page 12 / 55

The junction (1) must be at the rear edge of the SRS control module.

13 14 Remove the two screws and lift out the tunnel console. IMG Take the cable harness (C) from the kit and position it as illustrated. The junction (1) must be at the rear edge of the SRS control module. The cable marked with blue tape must go to the right seat and the other to the left seat. The cable with 2 x 4 pin connectors must be routed forward on the driver's side. IMG Page 13 / 55

14 16 Route the cables in the join for the floor mats further along the seat rail. Position the cable in a loop under the seat. IMG Take the cable with the two 4 pin connectors and route forward on the driver's side. IMG Page 14 / 55

18 Carry out points 18-45 on both sides of the seats

IMG-268411 19 Turn the panel upwards at the front edge.

15 18 Carry out points on both sides of the seats Remove the screw for the seat's side panel. IMG Turn the panel upwards at the front edge. Unhook it from the seat at the rear edge. IMG Page 15 / 55

16 20 Remove the knob for the lumbar support adjustment by removing the cover using a small screwdriver and pull the knob straight off. IMG Take a long cable tie from the kit and insert it through the hole for adjusting the lumbar support and inside the upholstery. The cable tie must be routed between the thin foam of the upholstery and the support pad. IMG Page 16 / 55

17 22A Illustrations A and B Remove cable harness (A) from the kit. Tape the cable terminals on the cable tie. Tape together as flat as possible. (Image B) Route the cable harness through and out at the headrest hole. Remove the cable tie from the cable harness. 22B IMG IMG Applies to the right-hand front seat Thread the cable tie from the headrest's inner mounting down to the hole for lumbar adjustment. The cable tie must be routed between the upholstery's thin foam and the protective pad (also see image 29). IMG Page 17 / 55

18 24 Applies to the left-hand front seat. Thread the cable tie from the headrest's outer mounting down to the hole for lumbar adjustment. The cable tie must be routed between the upholstery's thin foam and the protective pad (also see image 29). IMG Applies to both seats Tape the cable harness on the cable tie. Tape as flat as possible. See image 22 B. Pull it up towards the upper edge of the seat and out through the hole for the headrest. Remove the cable tie and tape from the cable harness. IMG Page 18 / 55

19 26 Caution! There are two brown cables in the cable harness. The brown cable to terminal 4 is twinned with the blue cable to terminal 3. Position: IMG Not connected. White (W) Blue (BL) Brown (BN) Red/White (R/W) Red (R) Black (SB) Brown (BN) Yellow (Y) Green (GN) Gray (GR) Pink (P) 27 Take the grey connector from the kit. Connect the cable harness terminals according to point 26. Press in the connector's catch. IMG Page 19 / 55

20 28 Adjust the length on the cable harness so that the connector protrudes 140mm. The cable harness must be positioned in front of the hole for the headrest. IMG Using your fingers, press the cable harness under the protective pad, the cable harness must not press out the upholstery after installation. 1. Padding 2. Protective pad IMG Page 20 / 55

21 30 Take the headrest and the upholstery from the kit. Pull the upholstery over the headrest. IMG Pull the two corners of the upholstery over. IMG Page 21 / 55

22 32 Hook the upholstery onto the two cutouts. IMG Fold in the upholstery's two reinforcements. IMG Page 22 / 55

23 34 Fold up the upholstery's reinforcement. Locate the hole under the upholstery on the side of the headrest. Note! The inward facing side in the car. Make a mark for making a hole using a piece of tape. Fold back the upholstery's reinforcement. IMG Install the 5 clips. IMG Page 23 / 55

24 36 Fold in the upholstery's mounting. IMG Take the display from the kit. Install on the headrest. IMG Page 24 / 55

25 38 Align the display in the headrest's two cutouts. IMG Install the two screws. IMG Page 25 / 55

26 40 Locate the hole under the upholstery on the headrest side, marked with tape. Make a hole in the upholstery using a scriber or an awl. Note! The inward facing side in the car. IMG Take the coat hook from the kit. Press into the hole. Tap it in lightly using a plastic hammer so that it secures properly. IMG Page 26 / 55

IMG-317335 43 Install the headrest on the seat.

27 42 Position the panel on the seat. Position the cable harness in the panel's cutout. IMG Install the headrest on the seat. Only slide it down so that the distance between the seat and lower edge of the headrest is approximately 50mm. IMG Page 27 / 55

28 44 Connect the connector and push the headrest down to the locked position. Check that the head restraint has locked into place by pulling it upwards. IMG Check that the headrest upholstery is correctly aligned against the panel. Repeat steps for the other side. IMG Page 28 / 55

46 Applies to the right-hand front seat and cars without heated seats Take a clip with cable tie from the kit and install it on the plate edge on the left-hand side of the right-hand seat.

29 46 Applies to the right-hand front seat and cars without heated seats Take a clip with cable tie from the kit and install it on the plate edge on the left-hand side of the right-hand seat. IMG Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the seat belt buckle. Tighten the cable tie (1). Secure the cable using two cable ties (2). IMG Page 29 / 55

Secure the cable using three cable ties (1).

30 48 Applies to the right-hand front seat and cars with heated seats Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the heating element. Secure the cable using three cable ties (1). IMG Applies to the right-hand front seat Route the cable harness in an arc under the seat. Secure it using three cable ties in the existing cable harness. IMG Page 30 / 55

50 Take a piece of foam tape from the kit and cut it in the centre. Fold the seat forward slightly and connect the cable harness from the floor to the connector (1).

Check that the cable harness is not trapped when the seat is slid forwards and backwards.

31 50 Take a piece of foam tape from the kit and cut it in the centre. Fold the seat forward slightly and connect the cable harness from the floor to the connector (1). Tape one cut piece of foam tape around the connectors. Place a cable tie on each side of the connectors and tighten. Check that the cable harness is not trapped when the seat is slid forwards and backwards. The right-hand seat means the passenger seat Fold the backrest forward and backwards and check that the cable harness is not trapped when folding the backrest. IMG Applies to the left-hand seat and cars without heated seats Take a clip with cable tie from the kit and install it on the plate edge on the right-hand side of the left-hand seat. IMG Page 31 / 55

52 Take the cable harness from the headrest and pull forward, underneath the seat. Follow the cable harness for the seat belt buckle. Tighten the cable tie (1).

32 52 Take the cable harness from the headrest and pull forward, underneath the seat. Follow the cable harness for the seat belt buckle. Tighten the cable tie (1). Secure the cable using two cable ties (2). IMG Applies to the left-hand front seat and cars with heated seats Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the heating element. Secure the cable using three cable ties (1). IMG Page 32 / 55

33 54 Applies to the left-hand front seat. Route the cable harness under the seat. Connect the cable harness from the floor to the connector (1). Secure it using a cable tie in the existing cable harness or in a bracket. Tape one cut piece of foam tape around the connectors. Place a cable tie on each side of the connectors and tighten. Check that the cable harness is not trapped when the seat is slid forwards and backwards. The left-hand seat means the passenger seat IMG Fold the backrest forward and backwards and check that the cable harness is not trapped when folding the backrest. 55 Applies to all models Fold the ashtray out, press it down and remove IMG Page 33 / 55

34 56 Pull out the cup holder to its limit position. IMG Turn the tunnel console. Lift up the catch and remove the cup holder. IMG Page 34 / 55

35 58 Remove the four screws. IMG Pull the opening handle. Remove the two screws and lift off the lower section. IMG Page 35 / 55

36 60 Fold the cover up and remove the two screws. Remove the cover by sliding it forward. The cover will not be reused. IMG Remove the plug for the 12 V socket. Remove the two rubber supports. IMG Page 36 / 55

37 62 Lift up the two catches and remove the inner section of the ashtray. It will not be reused. IMG Release the two catches and remove the 12 V socket. IMG Page 37 / 55

38 64 Mark as illustrated on the tunnel console's storage compartment. Pre-drill using a Ø 2.5 mm (3/32") bit. Drill out the hole. Use a Ø35 mm (1 3/8") diameter hole saw. Smooth off the hole edges. IMG Points apply when the tunnel console is not prepared for the RSE system Mark as illustrated on the tunnel console's upper section. Drill using a Ø 5mm (13/64") bit. IMG Page 38 / 55

39 66 Mark as illustrated on the tunnel console's upper section. Saw and cut out the hole according to the markings. IMG Applies to all models Take the lower section of the cover and cable harness (B) from the kit. Insert the end with the three (4 x with Digital TV receiver) connectors through the hole. Install the rubber grommet. IMG Page 39 / 55

40 68 Secure the cable harness with a tie strap. IMG Take the DVD unit and 4 M4x6 screws from the kit. Connect the three (4 x with Digital TV receiver) connectors to the DVD unit. IMG Page 40 / 55

the open button or screw tower. Install the four screws and tighten.

41 70 Place the DVD unit in the lower section of the cover as illustrated. Ensure that the cable harness goes under the DVD unit and does not protrude towards the open button or screw tower. Install the four screws and tighten. IMG Take the cover's upper section and 4 screws, PF5x16, from the kit. Install the cover. IMG Page 41 / 55

42 72 Turn the cover, install the four screws and tighten to 3 Nm (2.2 lbf.ft.). IMG Route the cable harness in from the DVD unit through the drilled hole and down on the right-hand side of the tunnel console. Install the rubber grommet. Check that the rubber grommet's flanges are against the console. IMG Page 42 / 55

43 74 Take the AV panel from the kit. Connect the green connector to it. IMG Install the 12 V socket to the panel. IMG Page 43 / 55

IMG-268466 77 Press the panel into place.

44 76 Secure the cable harness clips on the flange of the AV panel. IMG Press the panel into place. Secure the panel with one screw (ST 3.5x13) from the kit. IMG Page 44 / 55

45 78 Reinstall the rubber support, the ashtray and the plug for the 12 V socket. IMG Install the cover on the tunnel console and tighten with the two screws. IMG Page 45 / 55

46 80 Open and close the cover three times. Check that the lock at the front edge works and that the rubber bushings are in place. The cable harness should be in a loop as illustrated. IMG Turn the console and route the cable harness as illustrated. IMG Page 46 / 55

82 Thread the cable harness out through the square cut out on the lower section of the tunnel console. Secure the two clips of the cable harness on the plastic flanges.

47 82 Thread the cable harness out through the square cut out on the lower section of the tunnel console. Secure the two clips of the cable harness on the plastic flanges. Tighten the lower section using the 6 screws. IMG Take a cable tie and secure the 12V socket's cable by the clip on the cable harness from the DVD unit. The cable tie catch should point towards the outer side of the tunnel console. Reinstall the cup holder. IMG Page 47 / 55

48 84 Make marks for drill holes on the opening handle for the tunnel console as illustrated. Pre-drill using a Ø 2.5 mm (3/32") bit. Drill out the hole using a Ø 6 mm ( 15/64") drill bit. IMG Take the cover and 2 x PF5x12 screws from the kit. Install the cover on the opening handle. Digital TV receivers must then be installed: Continue with the installation instructions: TV receiver, digital. IMG Page 48 / 55

IMG-268491 87 Connect the 4 pin black connector from the cable harness

49 86 Reinstall the front tunnel console and at the same time pull up the connectors for the RSE system, 12 V socket and telephone if applicable. IMG Connect the 4 pin black connector from the cable harness (B) to the one disconnected from the AUX socket. IMG Page 49 / 55

50 88 Take the upper panel for the front tunnel console. Remove the AUX socket by releasing the catches at the front and rear edge. IMG Take the new AUX socket from the kit and connect it to the 7 pin connector from cable harness (B). Install the socket in the panel with the connector's catch backwards. IMG Page 50 / 55

90 Install the tunnel console's upper panel. Check that the panel hooks securely at the front edge. Reinstall the tunnel console's 8 screws and tighten them.

51 90 Install the tunnel console's upper panel. Check that the panel hooks securely at the front edge. Reinstall the tunnel console's 8 screws and tighten them. IMG Applies to cars with telephone Reinstall the telephone cradle with the screws (3). Route the telephone cable. Install the telephone cable in the load-removing grommet (2). Connect the connector (1). IMG Page 51 / 55

52 92 Applies to all models Connect the connector for the 12V socket. IMG Take the rear tunnel console. Connect the two connectors for the RSE system (3 x with Digital TV-receiver.) Take two pieces of foam tape from the kit and wrap them around the connectors. Cut off the foam tape excess. IMG Page 52 / 55

53 94 Insert the connectors into the tunnel console. Hook the connector on for the 12 V socket. Slide the rear tunnel console forwards in its grooves until it locks and check that the cable harness is not trapped. IMG Take the cable with the 2 x 4 pin connector and route forward on the driver's side. Fold the carpet to one side and place the cable underneath. IMG Page 53 / 55

54 96 Locate the 4 pin, grey connector for the power supply. It is secured on the thick cable harness under the dashboard on the driver's side. Note! The pre-routed connector is already connected on certain versions. IMG Connect the cable harness to the existing connector (1). Wrap a piece of foam tape around the connected connectors and cut off the excess. Install the connector (2) on the car's existing cable harness using a cable tie. Note! The pre-routed connector is already connected on certain versions. In such a case, disconnect it and connect both connectors from the new cable harness. Wrap a piece of foam tape around the connectors. IMG Reinstall: the small storage compartment the panel at the gear selector side panels the sound barrier Page 54 / 55

55 98 Install the batteries in the remote control and headsets. Region code the DVD player. Information is in VIDA under: Product specifications Design and Function 39 Media, communication and navigation 393 Equipment for entertainment Rear seat entertainment system Design To activate the TV function IMG Aim the remote control at the screen and press DAY/NIGHT ("on/off") for approx. 5 seconds until SERVICE MENU is displayed. Enter code 1971, press OK. Select SET TV, press OK. Select TV connected, press OK. Exit. 99 Installing decals (Only applies to USA and Canada) Take the black decal from the kit. Clean the area (1) where the decal will be located. Use a mixture of 30% windscreen washer fluid and 70% water. Wipe dry. Remove the backing paper from the adhesive side of the decal. Secure the decal as illustrated. Press the decal into place properly. R Page 55 / 55

393: Multimedia system for the rear seat Multimedia system for the rear seat

393: Multimedia system for the rear seat S80 (07-), 2008, B8444S, TF-80SC AWD, L.H.D, YV1AH852881073834, 073834 4/1/2013 PRINT 393: Multimedia system for the rear seat Multimedia system for the rear seat