ASTON SERIES COMPACT Commercial Ton Water Source/Geothermal Heat Pump. Submittal Data English Language/IP Units SD1022AGA 05/14

Transcription

1 ASTON SERIES COMPACT Commercial Ton Water Source/Geothermal Heat Pump Submittal Data English Language/IP Units SD1022AGA 05/14

2 Model Nomenclature GB V 048 T L C A N 15 A 16 N A SS 23 * Model Type GB Aston Compact Cabinet Configuration V Vertical H - Horizontal Unit Capacity (MBTUH) Single Speed 009, 012, 015, 018, 024, 0 036, 042, 048, 060, 070 Dual-Capacity 026, 038, 049, 064, 072 Discharge Configuration T Top (Vertical) E End (Horizontal) S Side (Horizontal) Return Air Configuration L Left R Right Voltage 0 8-2/60/ /60/1 ( ) 3 8-2/60/3 ( ) 4 460/60/3 ( ) 5 575/60/3 (PSC Only ) Refrigeration Option 0 None 2 HWG Only w/o Pump (Vertical ) G Hot Gas Bypass ( ) R Hot Gas Reheat ( ) B Hot Gas Bypass w/hot Gas Reheat ( ) Blower Options 0 PSC Blower (Single Speed Only) 1 Variable Speed ECM Blower ( ) 2 High Static Variable Speed ECM Blower (036, 038, 042, 048, 049) 3 High Static PSC Blower ( ) 4 5-Speed ECM Blower ( ) Water Coil Option C Copper D Insulated Copper N CuproNickel P Insulated CuproNickel Note: Phase Guard Only Available on 8-2/60/3, 460/60/3, and 575/60/3 Vintage * - Factory Use Only Non-Standard Options SS Standard Drain Pan Option 0 Composite, No Secondary Connection 1 Composite, Secondary Connection 2 Stainless Steel, No Secondary Connection 3 Stainless Steel, Secondary Connection Air Coil Option 3 Standard 4 AlumiSeal TM Filter Option A MERV 4 B MERV 13 Cabinet Option 0 Unpainted Cabinet, Filter Rail 1 Painted Cabinet, Filter Rail 2 Unpainted Cabinet, 4-Sided Filter Rack 3 Painted Cabinet, 4-Sided Filter Rack Electrical Option N None A IntelliStart Only E IntelliStart and Disconnect P Phase Guard, No Disconnect B Phase Guard, Disconnect D No Phase Guard, Disconnect Control Option A Aurora TM Base Control (ABC) 4 FX10 std. No Communications 5 FX10 w/ Open N2 Com Card 6 FX10 w/ LonWorks Com Card 7 FX10 w/ BacNet Com Card Water Control Option N None R Water Flow Regulator V 2-Way Valve B 2-Way Valve w/ Water Flow Regulator Sound Kit Option A None B Sound Kit Rev.: 24 April 14D SD1022AGA 05/14 2 Page of

3 AHRI Data PSC Motors ARI/ASHRAE/ISO English (IP) Units Model Capacity Modulation Flow Rate Water Loop Heat Pump Ground Water Heat Pump Ground Loop Heat Pump Cooling Brine Heating Cooling Heating Full Load 77 EWT 68 EWT 59 EWT Part Load 68 Cooling EWT 86 Heating Brine Full Load 32 Part Load 41 gpm cfm Capacity EER Capacity Capacity EER Capacity Capacity EER Capacity Btu/h Btuh/W Btu/h Btu/h Btuh/W Btu/h Btu/h Btuh/W Btu/h 009 Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , , , Cooling capacities based upon 80.6 DB, 66.2 WB entering air temperature Heating capacities based upon 68 DB, 59 WB entering air temperature All ratings based upon 8V operation Variable Speed ECM and 5-Speed ECM Motors AHRI/ASHRAE/ISO English (IP) Units Model Capacity Modulation Flow Rate Water Loop Heat Pump Ground Water Heat Pump Ground Loop Heat Pump Cooling Brine Heating Cooling Heating Full Load 77 EWT 68 EWT 59 EWT Part Load 68 Cooling EWT 86 Heating Brine Full Load 32 Part Load 41 gpm cfm Capacity EER Capacity Capacity EER Capacity Capacity EER Capacity Btu/h Btuh/W Btu/h Btu/h Btuh/W Btu/h Btu/h Btuh/W Btu/h 015 Single , , , , , , Single , , , , , , Single , , , , , , Single , , , , ,0 21.9, Single , , , , , , Single , , , , , , Single , , , , ,0.1 35, Single , , , , , , Single , , , , , , Full , , , , , ,0 4.3 Part 7.0 7, , , , , ,0 4.8 Full , , , , , , Part ,0.3 29, , , , , Full , , , , , ,0 4.0 Part , , , ,0 4.7, , Full , , , , , , Part , , , ,0 5.0, , Full , , , , , , Part , , , , , , Cooling capacities based upon 80.6 DB, 66.2 WB entering air temperature Heating capacities based upon 68 DB, 59 WB entering air temperature All ratings based upon 8V operation SD1022AGA 05/14 3 Page of

4 Vertical Dimensional Data Standard filter rails for open return applications Field installed duct flange Deluxe filter rack for ductable return applications A N R S A N Air coil Q Q ACCESS PANEL B P G F AIR COIL SIDE 4 3 FRONT 1.4 in (3.5 cm) Top View - Right Return M M AIR COIL SIDE FRONT 1.4 in (3.5 cm) Top View - Left Return 4 3 P G F B 2' (61 cm) Alternate Service Access 2' (61 cm) Service Access Left Return (Right Return opposite side) Isometric View - Left Return U T W Air coil Air coil ACCESS PANEL ACCESS PANEL V C H E D 1.6 in (4.1 cm) Condensate 3/4 in PVC glue socket 1.6 in (4.1 cm) L J supply 1 in (25.4 mm) knockout Low voltage 1/2" (12.7 mm) knockout L K 8 7 Condensate 3/4 in PVC glue socket 1.6 in (4.1 cm) E H D C 1.6 in (4.1 cm) J L 6 8 ACCESS PANEL 8 7 K L Front View - Right Return Front View - Left Return Right View - Right Return Left View - Left Return SD1022AGA 05/14 4 Page of

5 Vertical Dimensional Data cont. Vertical Models Electrical Knockouts Water Connections Overall Cabinet J K L 1/2 in. 1/2 in. A B C D E F G H Loop Knockout 1 in. cond cond cond Width Depth Height* In Out HWG In HWG Out Condensate Water FPT HWG Provisions Low Voltage Low Voltage in N/A N/A /2 in. N/A cm N/A N/A mm N/A in /4 in cm mm 22.2 mm in /4 in cm mm 22.2 mm in in cm mm 22.2 mm in in cm mm 22.2 mm Supply in in cm mm 22.2 mm Discharge Connection duct flange installed (±0.10 in) **Return Connection using deluxe fi lter rack (±0.10 in) Vertical Models M N P Q R S T U V W Filter Rack Return Supply Width Supply Depth Return Depth Width Height in cm in cm in cm in cm in cm in cm Condensate is 3/4 in. PVC female glue socket and is switchable from side to front. *Discharge flange is field installed and extends 1 in. (25.4 mm) from top of cabinet. **Vertical units shipped with standard 2 in. (field adjustable to 1 in.) open application filter rack extending 2.2 in. from unit and is not suitable for duct connection, for ductable return connection applications, order the deluxe 2 in. (field adjustable to 1 in.) duct collar/filter rack which extends 3.25 in. from the unit and is suitable for duct connections. Vertical Disconnect When using disconnect, do not use dimension L from the standard vertical dimensional data. Use dimension LL from the vertical disconnect dimensional data. Vertical Models LL [45.2] [36.3] [38.9] [36.3] [36.3] [36.3] External Dimensions in inches [cm] Supply 1.8 in. [4.6 cm] Disconnect Location LL Alternative Location Disconnect Located on this Side for a Right Return Vertical Shown in Left Return Configuration SD1022AGA 05/14 5 Page of

6 Horizontal Dimensional Data Right Return Standard filter rails 1 in. [2.5 cm] knockout 0.5 in. [1.3 cm] knockout Front K 1.7 in. [5.3 cm] CP 1.7 in. [5.3 cm] Standard filter rails Front Left Return AP J E AP CMP A RR Front View D AP CMP ' (61 cm) Service Access J 2' (61 cm) Service Access Condensate "X" PVC size End Discharge Deluxe filter rack option shown 2.3 in. [5.8 cm] N P H FILTER RACK AIR COIL SIDE Right Return End Discharge Side Discharge E D CP AP LR Front View Side Discharge Left Return End Discharge Condensate "X" PVC size End Discharge Deluxe filter rack option shown P N BLOWER L OUTLET Legend M C AP = Alternate Service Panel C M L BP CP = Blower Service Panel = Control Access Panel BLOWER OUTLET 2.1 in. [5.3 cm] CMP = Compressor Service Panel 2.1 in. [5.3 cm] A A K 0.5 in. [1.3 cm] knockout 1 in. [2.5 cm] knockout FILTER RACK AIR COIL SIDE 2.3 in. [5.8 cm] H P N 1.5 in. [3.8 cm] 1.5 in. [3.8 cm] N P BP L M BLOWER OUTLET Right Return Side Discharge AP CMP K 0.5 in. [1.3 cm] J knockout Front Front 1 in. [2.5 cm] J knockout 0.5 in. [1.3 cm] K knockout AP CMP Left Return Side Discharge BLOWER OUTLET M L BP Air Coil C Q S T T S Q FILTER RACK CONNECTION R Deluxe filter rack option (shown) C R FILTER RACK CONNECTION Air Coil Front Front B Right Return Side View B Left Return Side View SD1022AGA 05/14 6 Page of

7 Horizontal Dimensional Data cont. Water Connections Electrical Knockouts Overall Cabinet Horizontal J K Models A B C D E H Loop 1/2 in. cond 1 in. cond Width Depth Height* In Out Condensate Water FPT Low Voltage Supply in /2 in cm mm in /4 in cm mm in /4 in cm mm in in cm mm in in cm mm in in cm mm in in cm mm Discharge Connection Return Connection Horizontal duct fl ange installed (±0.10 in.) using deluxe fi lter rack option (±0.10 in.) PVC Size Models L M N P Q R S T X Supply Width Supply Depth Return Depth Return Height in /4 cm in /4 cm in /4 cm in /4 cm in /4 cm in /4 cm in / cm Horizontal units shipped with standard 2 in. (field adjustable to 1 in.) open application filter rack extending 2.2 in. from unit and is not suitable for duct connection, for ductable return connection applications, order the deluxe 2 in. (field adjustable to 1 in.) filter rail/filter rack which extends 3.25 in. from the unit and is suitable for duct connections. Horizontal Disconnect When using disconnect, do not use dimension K from the standard horizontal dimensional data. Use dimension KK from the horizontal disconnect dimensional data. Horizontal Models KK [.8] [23.4] [23.4] [28.4] [25.9] [28.4] [25.9] Dimensions in inches [cm] Disconnect Located on this Side for a Left Return 2.1 in. [5.3 cm] Disconnect Location KK Supply Horizontal Shown in Right Return Configuration SD1022AGA 05/14 7 Page of

8 Hanger Bracket Locations H Right Left B D E Compressor Section Air Handler Section F G C E D Compressor Section Air Handler Section G F A H 3/8 Threaded Rod (not supplied) Vibration Isolator Washer Bolt and Lockwasher Hex Nuts (not supplied) NOTE: Model sizes will be shipped with six (6) hanger brackets. Only five (5) hanger brackets will be used on the unit. See the above illustration for the fifth hanger bracket location. All other models will use four (4) hanger brackets. Hanger Bracket Dimensions Single Speed Dual Capacity Model Hanger Kit Part Number Unit Hanger Dimensions A B C H n/a in. 99S0A04 cm n/a in n/a 99S0A04 cm n/a in n/a 99S0A04 cm n/a in n/a 99S0A04 cm n/a in n/a 99S0A04 cm n/a in n/a 99S0A04 cm n/a in S0A03 cm in n/a 99S0A04 cm n/a in n/a 99S0A03 cm n/a in n/a 99S0A04 cm n/a in n/a 99S0A04 cm n/a in S0A03 cm Weight Distribution Single Speed Model Vertical Weight Horizontal Weight Horizontal Weight Distribution Front Back D E F G [78] [80] [15] [] [15] [] [78] [80] [15] [] [15] [] [95] [100] [29] [18] [32] [16] [95] [100] [29] [18] [32] [16] [127] [134] [34] [31] [34] [13] [129] [134] [34] [31] [34] [13] [136] [138] [39] [36] [39] [18] [166] [170] [52] [43] [34] [27] [168] [172] [54] [45] [36] [29] [186] [191] [54] [] [43] [36] [2] [6] [61] [54] [45] [39] [127] [134] [34] [31] [34] [13] [163] [170] [52] [43] [34] [27] [168] [172] [54] [45] [36] [29] [186] [191] [54] [] [43] [36] [2] [6] [61] [54] [45] [39] Weights are listed in lbs. [kg]. Dual Capacity SD1022AGA 05/14 8 Page of

9 Physical Data Model Single Speed Compressor (1 each) Rotary Scroll Factory Charge R-410A, oz [kg] Vertical 29 [0.82] 36 [1.02] 38 [1.08] 48 [1.36] 56 [1.59] 68 [1.93] 84 [2.38] 86 [2.44] 92 [2.61] 100 [2.83] 128 [3.63] Factory Charge R-410A, oz [kg] Horizontal 29 [0.82] 36 [1.02] 42 [1.19] 42 [1.19] 54 [1.53] 64 [1.81] 78 [2.21] 84 [2.38] 92 [2.61] 84 [2.38] 118 [3.35] Blower Motor & Blower Blower Motor Type/Speeds Blower Motor, hp [W] Oversized PSC Blower Motor, hp [W] Blower Wheel Size (Dia x W), in. [mm] Oversized Blower Wheel Size (Dia x W), in. [mm] VS ECM Not Available Variable Speed ECM 5-Spd ECM Not Available 5-Speed ECM PSC PSC 4 Speeds PSC - 3 Speeds VS ECM Not Available 1/2 [373] 1/2 [373] 1/2 [373] 1/2 [373] 1/2 [373] 1/2 [373] 1/2 [373] 1 [746] 1 [746] 5-Spd ECM Not Available 1/2 [373] 1/2 [373] 1/2 [373] 1/2 [373] 1/2 [373] 1 [746] 1 [746] 1 [746] 1 [746] PSC 1/10 [75] 1/10 [75] 1/6 [134] 1/6 [134] 1/5 [149] 1/3 [249] 1/2 [373] 1/2 [373] 1/2 [373] 1 [746] 1 [746] VS ECM Not Available 1 [746] 1 [746] Not Available PSC Not Available 1/3 [249] 1/2 [373] 1/2 [373] 3/4 [560] 3/4 [560] N/A N/A VS ECM 5-Spd ECM PSC VS ECM PSC Not Available Not Available 6 x 8 [152 x 3] 6 x 8 [152 x 3] 9 x 7 [229 x 178] 9 x 7 [229 x 178] 9 x 7 [229 x 178] Not Available 9 x 7 [229 x 178] 9 x 7 [229 x 178] 9 x 7 [229 x 178] Not Available 9 x 7 [229 x 178] 9 x 7 [229 x 178] 9 x 7 [229 x 178] 9 x 7 [229 x 178] 9 x 7 [229 x 178] 9 x 7 [229 x 178] 9 x 7 [229 x 178] 9 x 7 [229 x 178] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 10 x 10 [254 x 254] 11 x 10 [279 x 254] 10 x 10 [254 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 10 x 10 [254 x 254] 11 x 10 [279 x 254] 10 x 10 [254 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 10 x 10 [254 x 254] 11 x 10 [279 x 254] 10 x 10 [254 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] Not Available Not Available Coax and Water Piping Water Connections Size - FPT - in. [mm] 1/2 [12.7] 1/2 [12.7] 3/4 [19.05] 3/4 [19.05] 3/4 [19.05] 3/4 [19.05] 1 [25.4] 1 [25.4] 1 [25.4] 1 [25.4] 1 [25.4] HWG Connection Size - Female Sweat I.D. - in [mm] (Vertical Only) Not Available 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] Coax and Piping Water Volume - gal [l] 0.26 [0.98] 0.3 [1.12] 0.4 [1.49] 0.4 [1.49] 0.4 [1.49] 0.75 [2.83] 0.9 [3.41] 0.9 [3.41] 1.25 [4.72] 1.5 [5.68] 1.5 [5.68] Vertical Air Coil Dimensions (H x W), in. [mm] 12 x x x 19 x 24 x 28 x 28 x x 25 [ x 25 [ x 25 [ x 25 [914 [5 x 6] [6 x 6] [483 x 8] [483 x 8] [610x 8] [711 x 8] [711 x 635] x 635] x 635] x 635] x 635] Air Coil Total Face Area, ft 2 [m 2 ] 1.3 [0.121] 1.8 [0.167] 2.6 [0.242] 2.6 [0.242] 3.3 [0.7] 3.9 [0.362] 4.9 [0.455] 5.6 [0.5] 5.6 [0.5] 6.3 [0.585] 6.3 [0.585] Air Coil Tube Size, in [mm] 5/16 [7.9] 3/8 [9.5] 5/16 [7.9] 5/16 [7.9] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] Air Coil Number of rows Filter Standard - 1 in. [25mm] Pleated MERV 4 Throwaway, in [mm] Filter Standard - 2 in. [51mm] Pleated MERV 13 Throwaway, in [mm] Horizontal 1-16 x [6 x 8] 1-16 x [6 x 8] 1-16 x 18 [6 x 457] 1-16 x 18 [6 x 457] 1-24 x 24 [610 x 610] 1-24 x 24 [610 x 610] 1-24 x 24 [610 x 610] 1-24 x 24 [610 x 610] 28 x 24 [712 x 610] 28 x 24 [712 x 610] 28 x 24 [712 x 610] 28 x 24 [712 x 610] 28 x [712 x 762] 28 x [712 x 762] 32 x [813 x 762] 32 x [813 x 762] 32 x [813 x 762] 32 x [813 x 762] x 36 [762 x 914] x 36 [762 x 914] x 36 [762 x 914] x 36 [762 x 914] Air Coil Dimensions (H x W), in. [mm] 12 x 16 [5 x 6] 16 x 16 [6 x 6] 18 x 21 [457 x 533] 18 x 21 [457 x 533] 18 x 27 [457 x 686] 18 x [457 x 762] x 35 [8 x 889] x [8 x 1016] x [8 x 1016] x 45 [8 x 1143] x 45 [8 x 1143] Air Coil Total Face Area, ft 2 [m 2 ] 1.3 [0.121] 1.8 [0.167] 2.6 [0.242] 2.6 [0.242] 3.4 [0.316] 3.8 [0.353] 4.9 [0.455] 5.6 [0.5] 5.6 [0.5] 6.3 [0.585] 6.3 [0.585] Air Coil Tube Size, in. [mm] 5/16 [7.9] 3/8 [9.5] 5/16 [7.9] 5/16 [7.9] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] Air Coil Number of rows Filter Standard - 1 in. [25mm] Pleated MERV 4 Throwaway, in. [mm] 1-16 x 18 [6 x 8] 1-16 x 18 [6 x 8] 2-18 x 14 [457 x 356] 2-18 x 14 [457 x 356] 1-18 x 18 [457 x 457] 1-18 x 14 [457 x 356] 1-18 x 18 [457 x 457] 1-18 x 14 [457 x 356] 2-18 x [457 x 8] 1 - x [8 x 8] 1 - x 22 [8 x 559] 1 - x [8 x 8] 1 - x 22 [8 x 559] 1 - x 25 [8 x 635] 1 - x 22 [8 x 559] 1 - x 25 [8 x 635] 1 - x 22 [8 x 559] Filter Standard - 2 in. [51mm] Pleated MERV 13 Throwaway, in. [mm] 1-16 x 18 [6 x 8] 1-16 x 18 [6 x 8] 1-18 x 29 [457 x 737] 1-18 x 29 [457 x 737] 1-18 x 32 [457 x 813] 1-18 x 32 [457 x 813] 1 - x 37 [686 x 9] 1 - x [8 x 8] 1 - x 22 [8 x 559] 1 - x [8 x 8] 1 - x 22 [8 x 559] 1 - x 25 [8 x 635] 1 - x 22 [8 x 559] 1 - x 25 [8 x 635] 1 - x 22 [8 x 559] 4/11/14 SD1022AGA 05/14 9 Page of

10 Physical Data cont. Model Dual Capacity Compressor (1 each) Copeland 2-speed Scroll, UltraTech Factory Charge R410-A, oz [kg] Vertical 56 [1.59] 78 [2.21] 93 [2.64] 104 [2.95] 128 [3.63] Factory Charge R410-A, oz [kg] Horizontal 52 [1.47] 74 [2.10] 93 [2.64] 118 [3.35] 138 [3.91] Variable Speed ECM Blower Motor and Blower Blower Motor Type/Speeds Variable Speed ECM 5-Speed ECM VS ECM 1/2 [373] 1/2 [373] 1/2 [373] 1 [746] 1 [746] Blower Motor- hp [W] 5-Spd ECM 1/2 [373] 1/2 [373] 1 [746] 1 [746] 1 [746] Oversized Blower Motor- hp [W] VS ECM not available 1 [746] 1 [746] Not Available Not Available Blower Wheel Size (Dia x W), in. [mm] Blower Wheel Size (Dia x W), in. [mm] VS ECM 5-Spd ECM 9 x 7 [229 x 178] 9 x 7 [229 x 178] Oversized Blower Wheel Size (Dia x W), in. [mm] VS ECM Not Available 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] 11 x 10 [279 x 254] Not Available 11 x 10 [279 x 254] 11 x 10 [279 x 254] Not Available Coax and Water Piping Water Connections Size - FPT - in [mm] 3/4 [19.05] 1 [25.4] 1 [25.4] 1 [25.4] 1 [25.4] HWG Connection Size - Female Sweat I.D. - in. [mm] (Vertical Only) 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] 1/2 [12.7] Coax and Piping Water Volume - gal [l] 0.7 [2.6] 1.3 [4.9] 1.6 [6.1] 1.6 [6.1] 2.3 [8.7] Vertical Air Coil Dimensions (H x W), in. [mm] 24 x [610 x 8] 28 x 25 [711 x 635] 32 x 25 [813 x 635] 36 x 25 [914 x 635] 36 x 25 [914 x 635] Air Coil Total Face Area, ft 2 [m 2 ] 3.3 [0.7] 4.9 [0.451] 5.6 [0.5] 6.3 [0.585] 6.3 [0.585] Air Coil Tube Size, in. [mm] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] Air Coil Number of rows Filter Standard - 1 in. [25mm] Pleated MERV 4 Throwaway, in. [mm] Filter Standard - 2 in. [51mm] Pleated MERV 13 Throwaway, in. [mm] Horizontal Air Coil Dimensions (H x W), in. [mm] 28 x 24 [712 x 610] 28 x 24 [712 x 610] 18 x 27 [457 x 686] 28 x [711 x 762] 28 x [711 x 762] x 35 [8 x 889] 32 x [813 x 762] 32 x [813 x 762] x [8 x 1016] 36 x [914 x 762] x 36 [762 x 914] x 45 [8 x 1143] x 36 [762 x 914] x 36 [762 x 914] x 45 [8 x 1143] Air Coil Total Face Area, ft 2 [m 2 ] 3.4 [0.316] 4.9 [0.451] 5.6 [0.5] 6.3 [0.585] 6.3 [0.585] Air Coil Tube Size, in. [mm] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] 3/8 [9.5] Air Coil Number of rows Filter Standard - 1 in. [25mm] Pleated MERV 4 Throwaway, in. [mm] Filter Standard - 2 in. [51mm] Pleated MERV 13 Throwaway, in. [mm] 1-18 x 18 [457 x 457] 1-18 x 14 [457 x 356] 1-18 x 32 [457 x 813] 2-18 x [457 x 8] 1 - x 37 [8 x 9] 1 - x 22 [8 x 559] 1 - x [8 x 8] 1 - x [8 x 8] 1 - x 22 [8 x 559] 1 - x 25 [8 x 635] 1 - x 22 [8 x 559] 1 - x 25 [8 x 635] 1 - x 22 [8 x 559] 1 - x 25 [8 x 635] 1 - x 22 [8 x 559] 1 - x 25 [8 x 635] 1 - x 22 [8 x 559] 4/11/14 SD1022AGA 05/14 10 Page of

11 Electrical Availability PSC Static Single Speed Models Dual Capacity Models Voltage Option /60/1 8-2/60/1 w/intellistart 265/60/1 Standard 8-2/60/3 (also w/intellistart) 460/60/3 (also w/intellistart) 575/60/3 8-2/60/1 (also w/intellistart) 265/60/1 8-2/60/3 (also w/intellistart) High 460/60/3 (also w/intellistart) 575/60/3 1/2/13 5-Speed ECM Static Single Speed Models Dual Capacity Models Voltage Option /60/1 8-2/60/1 w/intellistart 265/60/1 Standard 8-2/60/3 (also w/intellistart) 460/60/3 (also w/intellistart) 575/60/3 1/2/13 Variable Speed ECM Static Single Speed Models Dual Capacity Models Voltage Option /60/1 8-2/60/1 w/intellistart 265/60/1 Standard 8-2/60/3 (also w/intellistart) 460/60/3 (also w/intellistart) 575/60/3 8-2/60/1 265/60/1 8-2/60/3 (also w/intellistart) High 460/60/3 (also w/intellistart) 575/60/3 1/2/13 SD1022AGA 05/14 11 Page of

12 Electrical Data PSC Motor Single Speed Model Rated Voltage Voltage Min/Max Compressor MCC RLA LRA LRA** Blower Motor FLA Total Unit FLA Min Circ Amp Max Fuse/ HACR Breaker /60/1 187/ n/a /15 265/60/1 238/ n/a / /60/1 187/ n/a /15 265/60/1 238/ n/a / /60/1 187/ n/a /60/1 238/ n/a / /60/1 187/ /60/1 238/ n/a /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ * 265/60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ * 265/60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ * 265/60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/3 187/ /60/3 414/ /15 575/60/3 517/ n/a /15 8-2/60/1 187/ * 8-2/60/3 187/ /60/3 414/ /60/3 517/ n/a /15 8-2/60/1 187/ /60/3 187/ /60/3 414/ /60/3 517/ n/a /15 8-2/60/1 187/ * 8-2/60/3 187/ /60/3 414/ /60/3 517/ n/a /15 8-2/60/1 187/ /60/3 187/ /60/3 414/ /60/3 517/ n/a /15 8-2/60/1 187/ /60/3 187/ /60/3 414/ /60/3 517/ n/a /06/13 HACR circuit breaker in USA only *With optional High-static PSC motor **With optional IntelliStart SD1022AGA 05/14 12 Page of

13 Electrical Data cont. 5-Speed ECM Motor Dual Capacity Single Speed Model Rated Voltage Voltage Min/Max Compressor MCC RLA LRA LRA** Blower Motor FLA Total Unit FLA Min Circ Amp Max Fuse/ HACR Breaker 8-2/60/1 187/ n/a /60/1 238/ n/a /15 8-2/60/1 187/ /60/1 238/ n/a /60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ HACR circuit breaker in USA only **With optional IntelliStart 5/21/13 SD1022AGA 05/14 13 Page of

14 Electrical Data cont. Variable Speed ECM Motor Single Speed Dual Capacity Model Rated Voltage Voltage Min/Max Compressor MCC RLA LRA LRA** CAUTION: When installing a unit with a variable speed ECM blower motor in 460/60/3 voltage, a neutral wire is required to allow proper unit operation. Blower Motor FLA Total Unit FLA Min Circ Amp Max Fuse/ HACR Breaker /60/1 187/ n/a /60/1 238/ n/a /60/1 187/ /60/1 238/ n/a /60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ * 265/60/1 238/ n/a /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ * 8-2/60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ * 8-2/60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /15 8-2/60/1 187/ /60/1 238/ n/a /60/3 187/ /60/3 414/ /60/1 187/ * 265/60/1 238/ n/a /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ * 8-2/60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ /60/1 187/ /60/3 187/ /60/3 414/ HACR circuit breaker in USA only 5/21/13 *With optional 1 HP variable speed ECM motor **With optional IntelliStart SD1022AGA 05/14 14 Page of

15 Blower Performance Data Standard PSC Motor Blower Blower Motor Airflow (cfm) at External Static Pressure (in. wg) Model Spd Size HP H MH x 8 1/10 ML* L H MH* x 8 1/10 ML L H M 9 x 7 1/ L H M 9 x 7 1/ L H M 9 x 7 1/ L H M 9 x 7 1/ L H M 10 x 10 1/ L H M 10 x 10 1/ L H M 10 x 10 1/ L H M 11 x L H M 11 x L Optional High Static PSC Motor Blower Blower Motor Airflow (cfm) at External Static Pressure (in. wg) Model Spd Size HP H M 9 x 7 1/ L H M 9 x 7 1/ L H M 10 x 10 1/ L H M 10 x 10 3/ L H M 10 x 10 3/ L Factory settings are in Bold Air flow values are with dry coil and 1 in. MERV 4. For wet coil performance first calculate the face velocity of the air coil (Face Velocity [fpm] = Airfl ow [cfm] / Face Area [sq ft]). Then for velocities of 0 fpm reduce the static capability by 0.03 in. wg, 0 fpm by 0.08 in. wg, 0 fpm by 0.12in. wg. and 0 fpm by 0.16 in. wg. * Denotes setting for 265 V operation. Setting Blower Speed - PSC CAUTION: Disconnect all power before performing this operation. BLOWER SPEED WIRE HIGH MEDIUM LOW PSC BLOWER MOTOR BODY SD1022AGA 05/14 15 Page of

16 Blower Performance Data cont. 5-Speed ECM - Single Speed Model Motor Spd Motor Tap T Stat Cnct. Blower Size Motor HP Airflow (cfm) at External Static Pressure (in. wg) High 5 Med High 4 W Med 3 9 x 7 1/ Med Low 2 Y Low 1 G High Med High 4 W Med 3 9 x 7 1/ Med Low 2 Y Low 1 G High 5 W Med High 4 Y Med 3 9 x 7 1/ Med Low 2 G Low High Med High 4 W Med 3 Y1 9 x 7 1/ Med Low Low 1 G High 5 W Med High 4 Y Med 3 11 x 10 1/ Med Low Low 1 G High Med High 4 W Med 3 11 x Med Low 2 Y Low 1 G High Med High 4 W Med 3 Y1 11 x Med Low Low 1 G High 5 W Med High 4 Y Med 3 11 x Med Low Low 1 G High 5 W Med High 4 Y Med 3 11 x Med Low Low 1 G Factory settings are in Bold Air fl ow values are with dry coil and standard 1 in. fi lter 11//12 About 5-Speed ECM Constant Torque Motors The 5-speed ECM is a Constant Torque ECM motor and delivers air flow similar to a PSC but operates as efficiently as a variable speed ECM motor. Because it is an ECM motor, the 5-speed ECM can ramp slowly up or down like the variable speed ECM motor. There are 5 possible speed taps available on the 5-speed ECM motor with #1 being the lowest airflow and #5 being the highest airflow. These speed selections are preset at the time of manufacture and are easily changed in the field if necessary. If more than one tap are energized at the same time, built in logic gives precedence to the highest tap number and allows air flow to change with G, Y1, Y2 and W signals. Each of those 5 speeds has a specific Torque value programmed into the motor for each speed selection. As static pressure increases, airflow decreases resulting in less torque on the rotor. The motor responds only to changes in torque and adjusts its speed accordingly. The 5-speed ECM motor is powered by line voltage but the motor speed is energized by 24VAC. 5-Speed ECM Benefits: - High efficiency - Soft start - 5 speeds with up to 4 speeds on-line - Built in logic allows air flow to change with G, Y1, Y2 and W signals - Super efficient low airflow continuous blower setting (G) SD1022AGA 05/14 16 Page of

17 Blower Performance Data cont. 5-Speed ECM - Dual Capacity Model 026 Motor Speed Motor Tap T stat Cnct. Blower Size Motor HP Airflow (cfm) at External Static Pressure (in. wg) High 5 W Med High 4 Y Med 3 9 x 7 1/ Med Low 2 Y Low 1 G High 5 W Med High 4 Y Med 3 Y1 11 x 10 1/ Med Low Low 1 G High 5 W Med High Med 3 Y2 11 x Med Low 2 Y Low 1 G High 5 W Med High 4 Y Med 3 11 x Med Low 2 Y Low 1 G High 5 W Med High 4 Y Med 3 11 x Med Low 2 Y Low 1 G Factory speed settings are in Bold Air fl ow values are with dry coil and standard fi lter For wet coil performance first calculate the face velocity of the air coil (Face Velocity [fpm] = Airfl ow [cfm] / Face Area [sq ft]). Then for velocities of 0 fpm reduce the static capability by 0.03 in. wg, 0 fpm by 0.08 in. wg, 0 fpm by 0.12in. wg., and 0 fpm by 0.16 in. wg. Highest setting is for auxiliary heat (W) and lowest setting is for constant blower (G). The Y1 and Y2 settings must be between the G and W settings. Setting Blower Speed - 5-Speed ECM 5-speed ECM blower motors have five (5) speeds of which three (3) are selectable on single speed and four (4) are selectable on dual capacity. CAUTION: Disconnect all power before performing this operation. 5-Speed ECM Motor Connections - Single Speed 5-Speed ECM Motor Connections - Dual Capacity C - Black L - Orange G - Green C High Voltage Connections 3/16 in. L G N N - Brown C - Black L - Orange G - Green C High Voltage Connections 3/16 in. L G N N - Brown G - Blue Y1 - Red Low Voltage Connections 1/4 in. AUX - Gray G - Blue Y1 - Red Low Voltage Connections 1/4 in. AUX - Gray Y2 - Tan SD1022AGA 05/14 17 Page of

18 Blower Performance Data cont. Variable Speed ECM Motor Single Speed Model Max ESP Blower Size Motor hp x 7 1/ x 7 1/ x 7 1/ x 7 1/ x 10 1/2 036 w/1hp* x x 10 1/2 042 w/1hp* x x 10 1/2 048 w/1hp* x x x 10 1 Dual Capacity Model Max ESP Blower Size Motor hp x 7 1/ x 10 1/2 038 w/1hp* x x 10 1/2 049 w/1hp* x x 10 1 Airflow DIP Switch Settings L M H L M H L M H L M H L M H L M H L M H L M H L M H L M H L M H L M H Air Flow DIP Switch Settings L M H L M H L M H L M H L M H L M H x 10 1 L M H Factory settings are at recommended L-M-H DIP switch locations M-H settings MUST be located within boldface cfm range Lowest and Highest DIP switch settings are assumed to be L and H respectively cfm is controlled within ±5% up to the maximum ESP Max ESP includes allowance for wet coil and 1 in. MERV 4 SD1022AGA 05/14 18 Page of

19 Operating Limits Operating Limits Cooling Heating () ( C) () ( C) Air Limits Min. Ambient Air Rated Ambient Air Max. Ambient Air Min. Entering Air Rated Entering Air db/wb 80.6/ / Max. Entering Air db/wb 110/83 43/ Water Limits Min. Entering Water Normal Entering Water Max. Entering Water NOTE: Minimum/maximum limits are only for start-up conditions, and are meant for bringing the space up to occupancy temperature. Units are not designed to operate at the minimum/maximum conditions on a regular basis. The operating limits are dependent upon three primary factors: 1) water temperature, 2) return air temperature, and 3) ambient temperature. When any of the factors are at the minimum or maximum levels, the other two factors must be at the normal level for proper and reliable unit operation. Legend ABBREVIATIONS AND DEFINITIONS: cfm = airflow, cubic feet/minute EWT = entering water temperature, Fahrenheit gpm = water flow in gallons/minute WPD = water pressure drop, psi and feet of water EAT = entering air temperature, Fahrenheit (dry bulb/wet bulb) HC = air heating capacity, TC = total cooling capacity, SC = sensible cooling capacity, = total power unit input, kilowatts HR = total heat of rejection, HE = total heat of extraction, HWC = hot water generator capacity, EER = Energy Efficient Ratio = BTU output/watt input = Coefficient of Performance = Btu output/btu input LWT = leaving water temperature, LAT = leaving air temperature, TH = total heating capacity, LC = latent cooling capacity, S/T = sensible to total cooling ratio SD1022AGA 05/14 19 Page of