HANNAY REELS. Fire Fighting Reels. Hannay booster and large-diameter hose reels give you:

Transcription

1 Fire Fighting Reels HANNAY REELS Hannay booster and large-diameter hose reels give you: Faster clean up Preconnect or storage No draining, stacking, or dragging All sizes and capacities Efficient use of vehicle space Increased hose capacity H-9407-F Revision 6

2 INTRODUCTION It s easier to handle hose from booster to large diameter hose when Hannay Reels are lending a hand. Pumper with six reel units 1" booster hose to 4"LD collapsible hose. Fire fighters around the world depend on Hannay Reels. For decades, Hannay Reels has set the standard of quality and reliability for hose reels in the fire fighting industry. In supplying both apparatus manufacturers and after-market fire departments worldwide, Hannay has consistently serviced the needs of the industry. With Hannay Reels, there s no draining, stacking, or dragging. Plus, fire fighters appreciate quick attack and fast pick-up. Through research and development of internationally recognized standard models, to custom one-of-a-kind applications, Hannay continues to meet the specific needs of the vehicle or fire department. Our fire fighting reels come in all sizes and capacities and make efficient use of vehicle space. Numerous options and configurations are readily available to meet your needs. Attention Truck Committees and Specifiers of Fire Apparatus Products shown and described in this catalog are suggested models for broad use applications throughout the fire fighting industry. All our components are designed for multiple configurations to fit all your applications and space requirements. Therefore, all reel models can be adjusted dimensionally to fit your specific needs. For special requirements, contact your Hannay dealer or call our inside sales group. To order any Hannay Reel in this brochure, use the specifications listed here in conjunction with our Ordering Guide & Accessory Catalog.

3 Specifying Location of Components Optional Location of Components: Location of the inlet, outlet riser and rewind mechanism can be varied to meet your requirements and must be specified on your order. The drawings Right Top Rewind (RT) reels have the inlet, outlet riser and rewind mechanism on the operator s right. Hose unwinds from the top of the reel. Right Bottom Rewind (RB) reels have the inlet, outlet riser and rewind mechanism on the operator s right. Hose unwinds from the bottom of the reel. Note: Use position initials as suffix after model number, ie: EF RT Optional Motor Locations Electric rewind motors can be installed in any of the positions shown in these drawings. The Bottom Rear position is standard. The motor below show the component locations. Unless otherwise specified, most reels will be shipped as Right Top Rewind with the inlet, outlet riser and rewind mechanism on the operator s right. Left Top Rewind (LT) reels have the inlet, outlet riser and rewind mechanism on the operator s left. Hose unwinds from the top of the reel. Left Bottom Rewind (LB) reels have the inlet, outlet riser and rewind mechanism on the operator s left. Hose unwinds from the bottom of the reel. Bottom Rear Bottom Front Elevated 2 o clock Elevated 10 o clock (Standard) is installed inside the frame on Model ESF reels, which are designed for installation in restricted space. HOW TO SPECIFY HANNAY REELS Optional Auxiliary Rewind Positions Horizontal ring and pinion gear crank rewind mechanism is the standard configuration. Optional positions include vertical and 30 above centerline, as shown in these drawings. Both are available at extra cost and must be specified. Horizontal Vertical 30 Angle (Standard) Optional Roller Positions Optional roller assembly mounting kits, up to 2 of either can be mounted per reel. Consult factory, and indicate installation location front or rear of reel. High Mount Low Mount 1

4 Series F4000 Compact reels for booster hose. To handle single 3/4" I.D. or 1" I.D. hose. Series F4000 Standard Configuration Shown Compact reels for use in restricted spaces or on slide-on units. Also for use in brush and forest fire fighting vehicles. Rewind: Choose direct crank rewind (removable) or chain and sprocket drive powered by electric, hydraulic or compressed air motor. Crank is not supplied on power rewind models but is available at extra cost when specified. Brakes & Locks: Reels with direct crank rewind only are supplied with a spring tension brake, other brakes may be specified. (See Ordering Guide & Accessory Catalog.) Inlet: Standard inlet is 90-degree ball bearing swivel joint with 1" female NPT threads. Outlet: Standard outlet is 1" male NST threads (1.375" x 8 threads per inch). Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: F4000 series reels NOT recommended for use with Niedner Reeltex hose. 2

5 Series F4000 Specifications Dimensions and capacities E G 18.12" 460 B C 8" 203 H 9.88" 251 Y 10" 254 X D 14.5" 368 F4000 NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series F4000, request ISO 68. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Number inches Crank Rewind mm See Note 2 feet lb. m NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. I.D. (in) 3/4" 1" E F I.D. (mm) For power rewind ELEC ELEC O.D. (in) 1-9/32" 1-9/16" see Note 4 A B E AIR F AIR X NET SHIP O.D. (mm) CRANK HYD CRANK HYD F * F F A Specifications subject to change. Notes: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 2. Weights shown in chart are for crank rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric Hydraulic Air Dimension F is the overall length of standard model reels. On crank rewind models, the dimension shown is with the crank in rewind position. Reels require 3 1/2" clearance to remove crank handle. 4. When ordering power rewind models, prefix number with: A = Air Rewind E = Electric Rewind HD = Hydraulic Rewind (Air rewind reels are supplied with control valve and hose, 12v and 24v DC rewind reels are supplied with switch and solenoid, 115v AC rewind reels are not supplied with switch but can be ordered separately, hydraulic rewind reels are not supplied with control valve. *When shipped as a parcel package (via Fed-Ex or UPS Ground) 3

6 Series F For booster hose. To handle 3/4" I.D. or 1" I.D. hose. Series F The standard painted steel booster hose reel is the dependable, rugged reel that has set the standard for fire service reels for more than 50 years. The Super Booster reel is the top of the line. It weighs up to 50% less than standard booster reels and features an all-aluminum frame and drum, polished aluminum discs, and plated drive chain, sprocket, hub assembly, swivel joint and fasteners. No painting or finishing is required. When ordering place prefix SB before Model Number. Specifications and dimensions for Super Booster reels and standard booster hose reels are identical except for materials and weight. Rewind: Gear-driven crank rewind is standard. Choose chain and sprocket drive powered by electric, hydraulic or compressed air motor. Brakes & Locks: These reels supplied with a pinion brake as standard. Other brakes and locking devices may be specified. (See Ordering Guide & Accessory Catalog.) Inlet: Standard inlet is 1" 90-degree ball bearing swivel joint with 1" female NPT threads. Outlet: Standard outlet is 1" male NST threads. (1.375" x 8 threads per inch.) Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 4

7 Series F Specifications Dimensions and capacities B E 6 1/2" 165 C 10.5" 267 G H X A F Series F Y D NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series F, request ISO 84, for Super Booster, request ISO 122. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Approx. Weight Number inches (Steel) (Alum.) mm Crank Rewind Crank Rewind See Note 3 See Note 3 feet lb. lb. m NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. kg. I.D. (in) 3/4" 1" I.D. (mm) For power rewind F O.D. (in) 1-9/32" 1-9/16" see Note 4 A B D E CRANK F F G H X Y NET SHIP NET SHIP O.D. (mm) HYD ELEC AIR *F *F *F *F F F *F *F F F F F Specifications subject to change. Notes: 1. A two-way flow hub is available at no extra cost and must be specified. Assembly is threaded on both ends so swivel joint can be attached at either end of the reel. A pipe cap seals the opposite end. (See Ordering Guide & Accessory Catalog.) 2. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 3. Weights (lbs.) shown in chart are for manual rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric Air Hydraulic When ordering power rewind models, prefix model number with: E = Electric rewind (1/3 HP) EP = Electric rewind (1/2 HP) A = Air rewind HD = Hydraulic Rewind (Air rewind reels are supplied with control valve and hose; 12v and 24v DC rewind reels are supplied with switch and solenoid, 115v AC rewind reels are not supplied with switch but can be ordered separately, hydraulic rewind reels are not supplied with control valve.) 5. For polished aluminum reels, prefix complete model number with SB ; for example: SBEF * The F dimension for these models is shown for 1/3 HP motors. Add 2" to F dimension for 1/2 HP motors. The F dimension for all other reels is shown for 1/2 HP. Reels handling 200 or more must use 1/2 HP Motor. (Use prefix EP when ordering.) 6. When installing FH-3 rollers add 41/2 to D dimension. 5

8 Series SF For booster hose inboard mounted motor. To handle 3/4" I.D. or 1" I.D. hose. Series SF The inboard motor location and high profile of this reel make it suitable for installation in cabinets or wells that have space restrictions. All models are available as Super Booster reels with aluminum and plated components as described on page 4. Rewind: Gear-driven crank rewind is standard. Choose chain and sprocket drive powered by electric, hydraulic or compressed air motor. Brakes & Locks: These reels supplied with a pinion brake as standard. Other brakes and locking devices may be specified. (See ordering Guide & Accessory Catalog.) Inlet: Standard inlet is 1" 90-degree ball bearing swivel joint with 1" female NPT threads. Outlet: Standard outlet is 1" male NST threads (1.375" x 8 threads per inch). Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 6

9 Series SF Specifications Dimensions and capacities B E 6 1/2 165 C 10.5" 267 G H X A F Series SF NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series SF, request ISO 84. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Approx. Weight Number inches (Steel) (Alum.) mm Crank Rewind Crank Rewind See Note 3 See Note 3 feet lb. lb. m NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. kg. I.D. (in) 3/4" 1" I.D. (mm) For power rewind O.D. (in) 1-9/32" 1-9/16" see Note 4 O.D. (mm) A B D E F G H X Y NET SHIP NET SHIP SF SF SF *SF *SF SF SF *SF *SF *SF *SF Y D Specifications subject to change. Notes: 1. A two-way flow hub is available at no extra cost and must be specified. Assembly is threaded on both ends so swivel joint can be attached at either end of the reel. A pipe cap seals the opposite end (See Ordering Guide & Accessory Catalog.) 2. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 3. Weights (lbs.) in chart are for manual rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric Air Hydraulic When ordering power rewind models, prefix model number with: E = Electric Rewind (1/3 HP) EP = Electric Rewind (1/2 HP) A = Air Rewind HD = Hydraulic Rewind (12v and 24v DC rewind reels are supplied with switch and solenoid; 115v AC rewind reels are not supplied with switch but can be ordered separately.) (Use prefix EP when ordering.) 5. For polished aluminum reels, prefix complete model number with SB ; for example: SBESF All frames are rollformed channel, except Super Booster, which is square tubing. * Reels handling 200 or more must use 1/2 HP Motor. 7

10 Kit TF Twin Kit for booster hose reels. To handle 3/4" I.D. or 1-1/2" I.D. hose. Two F Series Reels, and a Twin Fire Reel Conversion Kit High mount top wind position Two F Series Reels, and a Twin Fire Reel Conversion Kit and Two optional outrigger roller assemblies Twin booster hose reels combine matched F or FF Series reels in a single unit with a center-mounted roller and spool assembly. Hose from both reels can be used on either side of the truck. Rugged unit frame construction maintains alignment and simplifies installation when two reels are combined. All models are also available as Super Booster reel with aluminum and plated components as described on page 4 or pages FH-3 Roller and Spool Assembly Not recommended for hoses larger than 1-1/2'' I.D. Speeds handling and reduces hose wear. Buffed stainless steel rollers resist corrosion, pitting and abrasion. Polished, chrome-plated spools and blocks add lasting beauty to your equipment. Delrin bearing surfaces assure quite operation and minimum wear. Assembly can be factory-installed, when specified, or ordered for field installation on reels or other equipment. To order: For factory installation, specify FH-3 Assembly and indicate position on reel. As a component, the complete model number of the reel must be specified. P/N FH-3 Top Wind Outrigger Mounting Brackets P/N

11 TF Kit Specifications Dimensions and options Twin Fire Reel Conversion Kit FH-3 Roller Assembly Frame Components Part No. Description (model of reel must be specified) Steel Reels Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for small steel pressed frame (23-24 and smaller) Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for large steel pressed frame (25-26 and larger) Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for steel roll form frame Super Booster Reels Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for small aluminum pressed frame (23-24 and smaller) Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for large aluminum pressed frame (25-26 and larger) Conversion Kit for Twin Fire Reel w/fh3 Roller Assembly for aluminum roll form frame Dimensions of Twin Kit for F Series Reels: (in conjunction with chart on page 5, after assembly) for models ending with E 48.5'' 52.5'' 60.5'' 66.5'' Dimension J 28.0'' 31.38'' 31.38'' 33.75'' E J Options: (model must be specified) For additional outrigger option (see lower photo top of page 8): you will need FH-3 Roller & Spool assemblies, and FH-3 Top Wind Outrigger Mounting Brackets. Assembly can be factory-installed, when specified, or ordered for field installation on reels or other equipment. 9

12 Series 7100/7200 For dual agent applications. To handle dual hose (3/4" I.D. thru 1 1/2" I.D.). Series 7100 Standard Configuration Shown These reels have two swivel joint inlets and two outlet risers to simultaneously handle two equal lengths of hose. Hoses can be different diameters, in which case the larger hose diameter determines the reel capacity. All models are available as Super Booster reel with aluminum and plated components as described on page 4. Rewind: Gear-driven crank rewind is standard. Choose chain and sprocket drive powered by electric, hydraulic or compressed air motor. Brakes & Locks: These reels supplied with a pinion brake as standard. Other brakes and locking devices may be specified. (See ordering Guide & Accessory Catalog.) Inlet: Series 7100 Standard inlets are 1" 90-degree ball bearing swivel joints with 1" female NPT threads. Series 7200 Standard inlets are 1 1/2" 90-degree ball bearing swivel joints with 1 1/2" female NPT threads and 2" victaulic groove. Outlets: Series 7100 Standard outlets are 1" male NST threads (1.375" x 8 threads per inch). Series 7200 Standard outlets are 1 1/2" male NST threads (1.990" x 9 threads per inch). Other sizes and/or threads can be furnished and must be specified. Standard inlets, outlet risers and hub assemblies are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: Series 7100 These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Series 7200 These reels operate at pressures to 600 psi (41 bar) and handle product temperatures from 20º F to +225º F ( 29º C to +107º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 10

13 Series 7100/7200 Specifications Dimensions and capacities B E 6 1/2 165 C 10.5" 267 G H X A F Series 7100/7200 Y D NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series 7100, request ISO 72, for Series 7200, request ISO 74. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Number inches Crank Rewind mm See Note 2 feet lb. m NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. I.D. (in) 3/4" 1" 1-1/2" I.D. (mm) For power rewind O.D. (in) 1-9/32" 1-9/16" 2-1/16" see Note 4 F F F F O.D. (mm) A B D E CRANK ELEC AIR HYD G H X Y NET SHIP 2/100 2/ /31 2/ /150 2/ /46 2/ /200 2/ /61 2/ /250 2/ /76 2/ / / / / / / Specifications subject to change. Notes: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 2. Weights in chart are for manual rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric Air Hydraulic When ordering power rewind models prefix model number with: EP = Electric Rewind (1/2 HP) A = Air Rewind HD = Hydraulic Rewind (Air rewind reels are supplied with control valve and hose, 12v and 24v DC rewind reels are supplied with switch and solenoid 115v AC rewind reels are not supplied with switch but can be ordered separately, hydraulic rewind reels are not supplied with control valve.) 4. For polished aluminum reels, prefix complete model number with SB ; for example: SBEP

14 Series 3100/3600 For industrial fire protection. To handle 3/4" I.D. thru 1 1/2" I.D. hose. Series 3600 These reels are designed to handle booster hose or preconnected collapsible hose for in-plant, forestry and off shore fire protection systems. The reel can be installed on the floor or wall. Since water is always available at the reel, the reel can also be used for general warehouse and maintenance operations. These reels are constructed of steel, with optional construction of aluminum or stainless steel. Optional finishes of galvanized or special paint systems including E coat and marine grade finishes for salt water environments are available. Consult factory for additional information and pricing. Rewind: Choose disc rewind or removable direct crank rewind. Brakes & Locks: Reels are supplied with spring actuated pinlock. Other brakes and locks may be specified. (See Ordering Guide & Accessory Catalog.) Inlet: Series 3100 Standard inlet is 1" 90-degree ball bearing swivel joint with 1" female NPT threads. Series 3600 Standard inlet is 1 1/2" 90-degree ball bearing swivel joint with 1 1/2" female NPT threads and 2" victaulic groove. Standard Configuration Shown Outlet: Series 3100 Standard outlet is 1" male NST threads (1.375" x 8 threads per inch). Series 3600 Standard outlet is 1 1/2" male NST threads (1.990" x 9 threads per inch). Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Optional Pressures & Temperatures: Series 3100 These reels operate at pressures to 1000 psi (69 bar) and handle product temperatures from 80º F to +185º F ( 62º C to+85º C). Series 3600 These reels operate at pressures to 600 psi (41 bar) and handle product temperatures from 20º F to +225º F ( 29º C to +107º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 12

15 Series 3100/3600 Specifications Dimensions and capacities E B G C 10.5" 267 H Y D 21.75" " 648 Series 3100/3600 X A F NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series 3100, request ISO 113, for Series 3600, request ISO 111. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Number inches Crank Rewind feet mm lb. m kg. collapsible NOTE 1 inch = 25.4 mm x, y indicate mounting holes I.D. (in) 3/4" 1" 1-1/2" 1" 1-1/2" 1-3/4" I.D. (mm) O.D. (in) 1-9/32" 1-9/16" 2-1/16" 1/2x1-3/4" 3/4"x3" 7/8"x3-1/4" O.D. (mm) x44 19x76 22x83 A B D E F G H X NET SHIP Specifications subject to change. Notes: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 2. Power rewind are not available on these models. See Series F or FF. 3. Four inches clearance needed for crank handle removal. 13

16 Series FF For large booster hose or preconnected collapsible hose. To handle 1 1/4" I.D. or 1 1/2" I.D. booster hose or 1 1/2" I.D. or 1 3/4" I.D. collapsible hose. Series FF Standard Configuration Shown These reels have a 1 1/2" I.D. full-flow hub assembly to accommodate large diameter booster hose or preconnected collapsible hose. The flanged outlet riser can be removed for easy hose installation. All models listed can be supplied without inlet, outlet riser, or hub assembly for dry storage of collapsible hose. All models are available as Super Booster reel with aluminum and plated components as described on page 4. Rewind: Gear-driven crank rewind is standard. Choose chain and sprocket drive powered by electric, hydraulic or compressed air motor. Brakes & Locks: These reels supplied with a pinion brake as standard. Other brakes and locking devices may be specified. (See ordering Guide & Accessory Catalog.) Inlet: Standard inlet is 1 1/2" 90-degree ball bearing swivel joint with 1 1/2" female NPT threads and 2" victaulic groove. Outlet: Standard outlet is 1 1/2" male NST threads. (1.990" x 9 threads per inch.) Other sizes and/or threads can be furnished and must be specified. Standard inlet, outlet riser and hub assembly are steel. These components can be supplied in stainless steel, at extra cost, to meet special product handling requirements. Optional Rollers: Rollers may be purchased as accessory items. Specify roller position when ordering. Mounting brackets are necessary. (See Ordering Guide & Accessory Catalog.) Operating Pressures & Temperatures: These reels operate at pressures to 600 psi (41 bar) and handle product temperatures from 60º F to +175º F ( 51º C to +79º C). Reels to operate at other pressures and temperatures can be furnished at extra cost. CAUTION: When using Niedner Reeltex hose a special riser and/or larger drum diameter is required (consult factor y). 14

17 Series FF Specifications Dimensions and capacities B E 6 1/2 165 C 10.5" 267 G H NOTICE: A FLEXIBLE CONNECTOR MUST BE USED BETWEEN THE INLET PIPE AND THE INLET SWIVEL JOINT. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series FF, request ISO 18. Specifications subject to change. Notes: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters. 2. Weights in chart are for manual rewind models. Add these amounts for power rewind models. Net (lbs.) Ship (lbs.) Net (kg.) Ship (kg.) Electric Air Hydraulic X A F Series FF Hose Capacity of Reel Model Reel Dimensions Approx. Weight Approx. Weight Number inches (Steel) (Alum.) mm Crank Rewind Crank Rewind feet See Note 3 See Note 3 m lb. lb. collapsible NOTE 1 inch = 25.4 mm x, y indicate mounting holes kg. kg. I.D. (in) 1-1/4" 1-1/2" 1-1/2" 1-3/4" I.D. (mm) For power rewind O.D. (in) 1-13/16" 2-1/16" 3/4"x3" 7/8"x3-1/4" see Note 3 O.D. (mm) x76 22x83 A B D E F G H X Y NET SHIP NET SHIP FF FF FF FF FF FF FF When ordering power rewind models, prefix model number with: EP = Electric Rewind ( 1 /2 H.P.) A = Air Rewind HD = Hydraulic Rewind (Air rewind reels are supplied with control valve and hose; 12v and 24v DC rewind reels are supplied with switch and solenoid. 115 v AC rewind reels are not supplied with switch but can be ordered separately, hydraulic rewind reels are not supplied with control valve.) 4. For polished aluminum reels, prefix complete model number with SB ; for example: SBEPFF Dimensions shown for reels up to and including disc size reflect pressed frames. All others are rollformed channel frames, except Super Booster, which is square tubing. Y D 15

18 Series LD Reels and spools to handle up to 6" I.D. collapsible hose. Typical Installations: Single large-capacity reel installed in the hose bed area to handle long lengths of pre-coupled hose. Hose pays out from the top of the reel so gravity assists unwinding. Two reels installed in the hose bed. In this arrangement, the upper reel is unloaded only if necessary. Payout and rewinding of the upper reels are facilitated by the position of the lower reel. Two reels with larger-diameter discs and narrower drums can also be installed sideby-side in the rear of the hose bed to handle approximately the same amount of hose. This method allows a center walkway or paying out two lines simultaneously if required. Hannay Reels offer the most efficient method of handling large diameter collapsible hose. Payout is fast and direct. Rewinding is considerably faster than reloading a hose bed, and reeling the hose eliminates sharp bends in the hose. Drainage is also facilitated by reeling. Location of these large reels on the apparatus is unique to each fire department and its specific needs. A single large reel is favored by some departments, while others find a pair of somewhat smaller reels to be more efficient. The illustrations above show frequently used installations and they are intended only as a guide. Hannay Reels standard reels for large-diameter collapsible hose are of all-steel construction; however, they can be constructed of all-aluminum if required for finish and weight considerations. Reel and Spool Specifications Description: Spools include discs, drum, axle and sprocket for chain. (Chain and rewind motor not supplied.) Spool assemblies include all components except the frame which is fabricated by the apparatus builder. Reel assemblies include discs, drum, axle, pillow block bearings, rewind mechanism, motor and frame. Discs are either heavy gauge steel with rolled edges and concentric reinforcing ribs or 3/16" thick steel with 1/2" rod welded around circumference (also available in aluminum). Drums are formed by reinforced tie rods with radial supports. Frames are heavy duty square tubing. Rewind options: Chain and sprocket drive mechanism powered by electric or hydraulic rewind motors. Electric rewind system includes 12v or 24v DC motor with reversible leads, remote push-button operating switch, solenoid and connectors. A clutch reduction unit is standard and installed on the reel assembly to increase torque and permit slower operating speeds. The rewind motor can be installed inboard or outboard of the reel frame. A variety of hydraulic rewind systems can be configured with standard hydraulic components (see hydraulic circuit information on page 17). Reel and spool assemblies are equipped with a reversible type hydraulic motor with SAE O-ring fittings. Other hydraulic system components are supplied by truck or vehicle manufacturer. Consult factory for hydraulic motor requirements. Brakes: A caliper disc brake system is supplied, when specified, to control reel unwinding speed (when free-wheeling) and/or to lock the reel while the vehicle is traveling. The brake is hydraulically operated and is self-contained. Important: Hose capacity is based on the flat hose dimensions listed below, with couplings at 100 foot intervals. Flat Hose Dimensions THICK x WIDTH I.D. THICK x WIDTH METRIC EQUIVALENT 1" 1 /2" x 1 3 /4" 12.7 x /2" 3 /4" x 3" 19.0 x /4" 7 /8" x 3 1 /4" 22.2 x " 3 /4" x 3 1 / x /2" 3 /4" x 4" 19.0 x " 1 /2" x 5" 12.7 x " 1 /2" x 6 1 /2" 12.7 x " 1 /2" x 8" 12.7 x " 1 /2" x 10" 12.7 x

19 LD Reels and Spools Installation Guide Hydraulic Requirements It is IMPORTANT that the End user provide the O.E.M. with complete specifications as to the required operation of the large diameter reel being specified. Any speed and torque requirements MUST be known to properly specify the correct reel for the application. The schematics shown here are EXAMPLES ONLY! THE CORRECT PUMP AND HYDRAULICS ARE THE RESPONSIBILITY OF THE TRUCK MANUFACTURER, in conjunction with the PURCHASER. Notes: 1. The schematics shown are for reference only and may not necessarily reflect customer requirements. 2. Hannay Reels does not recommend specific brands for hydraulic system components. We suggest you work with your hydraulic component supplier to meet your specs. Series LD Reel with hydraulic motor rewind and optional caliper disc brake installed. Custom Reels The standard reel assembly and spool assembly models listed represent the most frequently specified customer requirements for handling large-diameter fire hose. Because of the many possible variations in reel installation and hose capacity requirements, we will also custom build reels and spools to your specifications to become an integral part of the apparatus. Reels can be built of either steel or aluminum construction and various finishes are available. 17

20 LD REEL & SPOOL CONFIGURATIONS Reel & Spool Configurations Version A, B, and C: Version A Spool with sprocket for No. 50 chain. Chain and rewind motor not supplied. Version B Spool assembly with No. 50 chain and sprocket and hydraulic rewind motor. Version C Spool assembly with No. 41 chain and sprocket and electric rewind motor with clutch and double reduction unit. Disc diameters (E dimension) up to and including 39" only. Version F Reel: Version F Complete reel assembly with No. 50 chain and sprocket and hydraulic rewind motor mounted inside the frame. When ordering use prefix model number with HD; for example, HDLD version F. Version G Reel: Version G (high profile) complete reel assembly with chain and sprocket drive and electric rewind motor, including clutch and double reduction unit. Motor is mounted inside the frame. Disc diameters (E dimension) up to and including 39" only. When ordering use prefix model number with EP; for example, EPLD version G. F dimension = A dimension +4 C C C Version H Reel: Version H (low profile) complete reel assembly with chain and sprocket drive and electric rewind motor, including clutch and double reduction unit. Motor is mounted outside the frame. Disc diameters (E dimension) up to and including 39" only. When ordering use prefix model number with EP; for example, EPLD version H. Subtract 5" from dimensions G and H in chart for this version. F dimension = A dimension +7 C

21 Series LD Specifications See Reel & Spool Configurations on page 18. Be sure to check dimensions and weights prior to ordering. To receive a detailed parts breakdown drawing for Series LD, request ISO 104. Hose Capacity of Reel Model Reel Dimensions Approx. Weight Number NOTE 1 inch = 25.4 mm (Steel) Power Rewind feet inches lb. m mm kg. I.D. (in) 1-1/2" 1-3/4" 2" 2-1/2" 3" 4" 5" 6" I.D. (mm) A B D E G H NET SHIP LD LD LD LD LD LD LD LD LD LD Electric rewind not available on these models. Specifications subject to change. Note: 1. Upon request, reels can be supplied with drum lengths other than shown and with disc sizes in other diameters LD LD LD LD LD LD LD

22 NOTES 20

23 It s easier to handle hose from booster to large diameter hose when Hannay Reels are lending a hand.

24 Narrow roads in an old fishing village such as ours require long lengths of large diameter hose for proper water volume. Hannay Series LD fit the bill perfectly, fast payout and pickup answered our needs. Jim Burrows, Fire Coordinator Kennebunkport (ME) Fire Department Fire fighting and rescue operations all around the country depend on Hannay Reels. For years, Hannay has produced the best fire fighting and rescue hose and cable reels found anywhere in the world. Fire fighters and rescue squads have come to depend on Hannay Reels for their dependability, ease of use, and long life. But don t take our word for it. Here s what some of our customers have to say about Hannay Reels. Hannay Reels gives us easy hose dispersal and quick pick-up. Malcolm Farrell, Wilson Fire Department, Windsor, CT. The speed of our first attack is crucial, and Hannay Reels give us instant on with even partial payout. So we re right where the emergency is. Peter Goldstein, Coram, Long Island (NY) Fire Department In rescue operations, you have to be fast to be effective. Hannay Reels save us time in payout and clean-up. John Dugan, Wellsboro (PA) Fire Department To order Hannay Reels. Please refer to our Ordering Guide & Accessory Catalog enclosed in this package. For more information on all our hose and cable reels for fire fighting and rescue operations, please request our Triad Rescue Reels Catalog. 1st Lt. George Conklin of Unexcelled Fire Company states, Hannay makes the hardest job easier. When the men are exhausted and fatigued from fighting a fire, they can pack up the hose in one-third the time. Available from: The reel leader. 553 State Route 143 Westerlo, NY Telephone TOLL FREE GO REELS FAX REELING ( ) USA or FAX (International) WSP 10M 12/02 H-9407-F Revision 6