CONTENTS. GRIP TIGHT Adapter Ball Bearings

Transcription

1 CONTENTS GRIP TIGHT Adapter Ball Bearings Features / Benefits B2-2 How to Order / Nomenclature B2-4 Selection B2-5 Selection/Dimensions GRIP TIGHT Pillow Blocks GT Normal Duty B2-8 GTAH Air Handling B2-12 GTB Low Back B2-16 GTM Medium Duty B2-22 GTMAH Air Handling B2-26 GT Tapped Base B2-30 GRIP TIGHT 2 Bolt Flanges GT Normal Duty B2-32 GTAH Air Handling B2-36 GTM Medium Duty B2-40 GT LFT Normal Duty B2-42 GRIP TIGHT 3 Bolt Flanges GT FB Flanged Brackets B2-44 GT LF Normal Duty B2-46 GRIP TIGHT 4 Bolt Flanges GT Normal Duty B2-48 GTAH Air Handling B2-52 GTM Medium Duty B2-56 GTMAH Air Handling B2-60 GRIP TIGHT Piloted Flanges (fl anged cartridge) GT Normal Duty B2-64 GTM Medium Duty B2-66 GRIP TIGHT Take-Up Bearings GT Normal Duty Narrow Slot B2-68 GTM Medium Duty Narrow Slot B2-72 GT Normal Duty Wide Slot B2-74 GTM Medium Duty Wide Slot B2-78 GT Normal Duty Top Angle B2-82 GTM Medium Duty Top Angle B2-84 GRIP TIGHT Inserts GT Normal Duty B2-86 GTM Medium Duty B2-90 Related Products B2-96 Part Number Index Key Word Index GRIP TIGHT Adapter Ball Bearing E-Z KLEEN Bearing Quick Reference B2-1

2 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing GRIP TIGHT Adapter Ball Bearings DODGE proudly introduces a new, totally different ball bearing with a name that says it all: GRIP TIGHT. With its patent pending pull/push adapter system, fully concentric 360 inner ring, and completely interchangeable housing design, the new DODGE GRIP TIGHT Adapter ball bearing is the easy-on/ easyoff solution for damage free shafting, reduced vibration, and greater cost/inventory savings. The new GRIP TIGHT Adapter ball bearing is shaftready right out of the box and offered in a variety of housing styles for normal and medium duty operations. It accommodates commercial grade and some undersize shafting to lower costs, and all GRIP TIGHT Adapter assemblies fi t into a standard DODGE ball bearing housing. Plus this new DODGE bearing has been specifi cally engineered to run at higher speeds and operate cooler for longer grease life. In test comparisons, the new GRIP TIGHT Adapter ball bearing even proved it could suppress fretting corrosion and scarring to shafts and journals, thus saving not only time but added labor/maintenance costs. Easy-On / Easy-Off During mounting, the patent pending collar/inner ring system locks the tapered adapter sleeve under the bearing and onto the shaft. To dismount, the built in bearing puller pulls the bearing off the adapter and pushes the adapter in the opposite direction (out from under the bearing). Non-metallic retainer provides added strength Grade 10 balls promote quiet operation Lock/inner ring interface acts as bearing puller to ease disassembly Rugged housing for easy installation and alignment Case-carburized inner ring ensures greater wear resistance and longer life PROGUARD PLUS seal with fl ingers protects by keeping lubricants in, contaminants out B2-2

3 GRIP TIGHT Adapter Ball Bearings Housing Styles Off the shelf and shaft ready, the DODGE GRIP TIGHT Adapter ball bearing is offered for normal and medium duty in a variety of housing styles, including pillow block; tapped base; two-, three-, and fourbolt fl ange; piloted fl ange; take-up, and E-Z KLEEN design. Bearing Quick Reference Less Product Inventory for Signifi cant Savings With DODGE GRIP TIGHT Adapter ball bearings, you can reduce your inventory as much as 25% - 45%. Rather than inventory a complete line of individual bore sizes for each housing style, you can now purchase a housing assembly and adapters separately, with the adapter determining the bore size within a housing series. Damage Free ing The new DODGE GRIP TIGHT Adapter bearing features a unique adapter-mount design that is specifi cally developed to withstand axial forces that are generated during mounting or dismounting. The adapter provides superior holding power, as well as suppresses fretting corrosion and vibration. In test comparisons, a setscrew mounted bearing promotes shaft fretting corrosion and scarring. But the new DODGE GRIP TIGHT Adapter bearing comes off the shaft quickly and reveals no shaft fretting corrosion or scarring. There is no need to recondition your shaft so you save time and avoid added labor/ maintenance. E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Full Contact on for Better Grip, Less Vibration Setscrew locking can distort the inner ring and cause system induced vibration. But with the new DODGE GRIP TIGHT Adapter, the adapter attaches itself to the shaft for full concentric contact 360 through the length of the bearing. B2-3

4 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing HOW TO ORDER NOMENCLATURE GRIP TIGHT Thin Wall Adapter Ball Bearings There are two ways to specify DODGE Bearings. Most of the product offerings have part numbers with listings shown throughout this catalog. Use of the part numbers ensures accurate order processing. When part numbers are not shown, the product may be specifi ed by description or part name. Nomenclature P2B GT 104S NL This method is used when ordering units that include modifi cations or options. To order by description, use the nomenclature key shown below and add any special instructions to the end of the description for options not covered by the nomenclature. Modifi cation or feature CR = Corrosion Resistant Insert HT = High Temperature option (400 F maximum) LL = Low torque labyrinth seal MOD = Modifi ed NL = No Lube Fitting (sealed for life) P = Polymer Housing SH = Stainless Steel Housing Inches: First digit = Number of inches Second & third digits = Numbers of sixteenths of an inch 104 = Indicates 1-4/16 or 1-1/4 S = Next smaller ring size. E.g. 1-1/4 would be written as 104S Metric First two digits = number of millimeters M = Metric Bearing Type GT = Wide inner ring, normal duty, thin wall adapter locking GTM = Wide inner ring, medium duty, thin wall adapter locking Suffi xes to the above: AH = Air Handling B = Low backing height pillow block EZ = E-KLEEN (used with polymer and stainless steel housed units) U = Higher back pillow block (for interchangeability with competitor pillow blocks) Housing F2B = 2 bolt fl ange F4B = 4 bolt fl ange FB = Flange bracket FC = Flanged cartridge (piloted fl ange) INS = Insert NSTU = Narrow slot take-up P2B = 2 bolt base pillow block TB = Tapped base pillow block WSTU = Wide slot take-up /DIMENSIONS PAGE B2-30 B2-4

5 DODGE mounted ball bearings are primarily designed for radial loading. However, they have the capacity to carry thrust loads and combined radial/thrust loads. The maximum recommended load which can be applied is limited by various components in the system, such as bearing, housing, shaft attachments, speed and life requirements. DODGE mounted ball bearings have been applied successfully when these limits have been exceeded under controlled operating conditions. Contact DODGE Engineering for applications which exceed these recommendations. Select a bearing from the Selection Chart that has a radial load rating at the operating speed equal to or greater than the calculated Equivalent Radial load for a desired L10 life. This simple method is all that is required for the majority of general applications and provides for occasional average shock loads. L 10 Hours Life-is the life which may be expected for at least 90% of a given group of bearings operating under identical conditions. For an L 10 hours life other than those listed in the Selection Chart, multiply the equivalent Radial load by one of the following factors. For 50,000 L 10 hours life, use a factor of 1.18 and for 80,000, use Then select a bearing from the bold face (30,000) L 10 ratings only in the Selection Chart that has a rating equal to or greater than this value. Heavy Service-For heavy shock loads, frequent shock loads or severe vibrations, add up to 50% (according to severity of conditions) to the Equivalent Radial Load to obtain a Modifi ed Equivalent Radial Load. Consult Application Engineering for additional selection assistance. A thrust load value of C/10 is recommended as a guide for general applications and will give adequate L10 life. Where substantial radial load pulls the housing away from the mounting base, both the hold-down bolts and housing must be of adequate strength. Auxiliary load carrying devices, such as sheer bars, are advisable for side or end-loading of pillow blocks and radial loads for fl ange units. To determine the L 10 hours life for loads and RPM s not listed use the following equation: (3) C L 10 = x P RPM ( ) Where: L 10 = Life, hours C = Dynamic Capacity, lbs. or N P = Equivalent Radial Load, lbs. or N When the load on a ball bearing is solely a radial load with no thrust (axial) load, the Equivalent Radial Load (P) is equal to the actual radial load. However, when a thrust (axial) load is applied, the radial and thrust loads applied must be converted into an Equivalent Radial Load. The use of the X (radial factor) and Y (thrust factor) from Table 1 convert the actual applied thrust and radial loads to an Equivalent Radial Load which has the same effect on the life of a bearing as a radial load of this magnitude. P = (X x F R ) + (Y x F A ) Where: P = Equivalent Radial Load, lbs. F R = Radial load, lbs. F A = Thrust load, lbs. e = Thrust load to radial load factor (Table 1 ) X = Radial load factor (Table 1 ) Y = Thrust Factor (Table 1 ) C O = Basic static capacity To fi nd X and Y, fi rst calculate F A /C O to determine e. Calculate F A /F R and compare to e to determine the X and Y factors to use from Table 1. Substitute all known values into the Equivalent Radial Load equation. The Equivalent Radial loads (P) thus determined can be used in the L 10 life formula or compared to the allowable Equivalent Radial Load rating desired in the expanded rating chart to select a bearing (Table 2 ). If calculated value of P is less than F R, use P=F R. Table 1: Radial/Thrust Factors If F F A /F R is equal to or less A If F e than e A /F R is greater than e F A /F R e F A /F R > e C O X Y X Y Lubrication-DODGE Ball Bearings are lubricated at the factory and are ready to run. The bearings are initially lubricated with a lithium complex based grease and should be relubricated with the same or some equivalent. For high speeds, high loads, extreme temperatures and other abnormal operating conditions, special greases may be required. Contact DODGE Application Engineering for recommendations on these types of applications. Misalignment-DODGE Ball Bearings are designed to allow a maximum of ± 2 static misalignment. These bearings are not suitable for dynamic misalignment. To ensure good alignment, mounting surfaces must be checked for fl atness and must lie in the same plane. When tightening base bolts, each bolt should be alternately tightened in incremental torque values until full torque is achieved to prevent the angular shifting of the pillow block that occurs when one bolt is tightened to its full torque. Shimming may be required to minimize misalignment. Tolerances Normal Inches Commercial Tolerances Inches Up to 1-1/ Over 1-1/2 to 2-1/ Over 2-1/ Recommended Tolerances GRIP TIGHT Ball Bearings Inches GRIP TIGHT Adapter Ball Bearing E-Z KLEEN Bearing Quick Reference B2-5

6 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Table 2: Easy Selection Table Ring GT GTM DYNAMIC CAPACITY C (LBS) STATIC CAPACITY Co (LBS) Max RPM Proguard Plus Labyrinth (Contact) Seal (LL) Seal L10 LIFE Hours ALLOWABLE EQUIVALENT RADIAL LOAD RATINGS (LBS.) AT VARIOUS RPM ,000 1,500 1,750 2,200 2,600 3,000 3,200 3,600 20, /2 30, /8-2,158 1,000 12,000 14,500 40, mm 60, , , /4 30, ,899 1,390 10,000 13,000 40, mm 60, , /8 15/ mm 1-1/8 1-3/16 1-1/4 30mm 3/4 3,146 1,565 9,000 12, mm 4,368 2,250 7,500 11,000 20, , , , , ,000 1, , , , , /4 20,000 1,471 1, /16 1-3/8 30,000 1, /4 5,759 3,065 6,300 9,500 40,000 1, /16 30mm 60,000 1, mm 100, ,000 1,873 1,299 1, /16 1-1/2 30,000 1,636 1, /2** 7,332 4,005 5,600 8,500 40,000 1,487 1, mm 35mm 60,000 1, ,000 1, /8 20,000 2,016 1,398 1, /16 1-1/2 30,000 1,761 1,221 1, ,891 4,450 5,300 8,000 40,000 1,600 1, /4 40mm 60,000 1, mm 100,000 1, ,000 2,016 1,398 1, / /16 30,000 1,761 1,221 1, /4 7,891 4,450 4,800 7,500 40,000 1,600 1, mm 45mm 60,000 1, ,000 1, ,000 2,492 1,728 1,457 1,157 1, /16 30,000 2,177 1,509 1,273 1, /16 2 9,755 5,630 4,300 6,700 40,000 1,978 1,371 1, mm 50mm 60,000 1,728 1,198 1, ,000 1,457 1, ,000 3,012 2,088 1,761 1,398 1,221 1, /4 2-3/16 30,000 2,631 1,824 1,539 1,221 1, /16 2-1/4 11,791 6,955 4,000 6,000 40,000 2,391 1,657 1,398 1, mm 55mm 60,000 2,088 1,448 1, ,000 1,761 1,221 1, /16 70mm 2-7/16 2-1/2 65mm / /16 75mm 70mm 20,000 3,575 2,479 2,091 1,659 1,450 1,317 1,150 1,093 1, ,000 3,123 2,165 1,826 1,450 1,266 1,150 1, ,995 8,410 3,600 5,000 40,000 2,837 1,967 1,659 1,317 1,150 1, ,000 2,479 1,719 1,450 1,150 1, ,000 2,091 1,450 1, ,000 3,799 2,634 2,222 1,763 1,540 1,400 1,223 1,161 1,076 1, ,000 3,319 2,301 1,941 1,540 1,346 1,223 1,068 1, ,872 9,255 3,200 4,800 40,000 3,015 2,091 1,763 1,400 1,223 1, ,000 2,634 1,826 1,540 1,223 1, ,000 2,222 1,540 1,299 1, ,000 4,446 3,083 2,600 2,064 1,803 1,638 1,431 1,359 1,259 1,191 1,136 1,112 1, /16 30,000 3,884 2,693 2,272 1,803 1,575 1,431 1,250 1,187 1,100 1, ,407 11,015 3,000 4,500 40,000 3,529 2,447 2,064 1,638 1,431 1,300 1,136 1,079 1, mm 60,000 3,083 2,138 1,803 1,431 1,250 1, ,000 2,600 1,803 1,521 1,207 1, ,000 5,479 3,799 3,204 2,543 2,222 2,019 1,763 1,675 1,552 1,468 1,400 1,370 1, /16 30,000 4,787 3,319 2,799 2,222 1,941 1,763 1,541 1,463 1,356 1,282 1,223 1,197 1, /2 85mm 21,451 13,940 2,600 3,800 40,000 4,349 3,015 2,543 2,019 1,763 1,602 1,400 1,330 1,232 1,165 1,111 1,087 1,045 60,000 3,799 2,634 2,222 1,763 1,541 1,400 1,223 1,161 1,076 1, ,000 3,204 2,222 1,874 1,487 1,299 1,181 1, ** Piloted fl ange Only Labyrinth seal required when operating in the shaded area /DIMENSIONS PAGE B2-8 B2-6

7 Table 2: Easy Selection Table L10 ALLOWABLE EQUIVALENT RADIAL LOAD RATINGS (LBS.) AT VARIOUS RPM Ring LIFE GT GTM 3,800 4,000 4,300 4,500 4,800 5,000 5,300 5,600 6,000 6,300 6,700 7,500 8,000 8,500 9,000 9,500 10,000 11,000 12,000 13,000 14,500 Hours 20, /2 30, /8-40, mm 60, , /4 20mm 7/8 15/ mm 1-1/8 1-3/16 1-1/4 30mm 1-1/4 1-3/8 1-7/16 35mm 1-1/2 40mm - 3/4 1 25mm 1-3/16 1-1/4 30mm 1-7/16 1-1/2** 35mm 1-5/8 1-11/16 1-1/2 1-3/4 40mm 45mm 1-15/ mm 2 2-3/16 55mm 2-1/4 2-7/16 60mm /16 70mm 1-11/16 1-3/4 45mm 1-15/ mm 2-3/16 2-1/4 55mm 2-7/16 2-1/2 65mm / /16 75mm 70mm / mm 20, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,000 1,050 1,032 1, , , , , ,000 1, /16 30,000 1, /2 40,000 1,027 85mm 60, , ** Piloted Flange Only Labyrinth seal required when operating in the shaded area GRIP TIGHT Adapter Ball Bearing E-Z KLEEN Bearing Quick Reference B2-7

8 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY PILLOW BLOCKS (GTU) (GTU) 207 Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1/ P2B-GT AN-GT / P2B-GT P2B-GT AN-GT mm P2B-GT-17M AN-GT-03-17M 1/ P2B-GTU AN-GT / P2B-GTU P2B-GTU AN-GT mm P2B-GTU-17M AN-GT-03-17M 3/ P2B-GT AN-GT P2B-GT-04 20mm P2B-GT-20M AN-GT-04-20M 7/ P2B-GT AN-GT / P2B-GT AN-GT P2B-GT P2B-GT AN-GT mm129 P2B-GT-25M AN-GT-05-25M 1-1/ P2B-GT AN-GT / P2B-GT AN-GT P2B-GT / P2B-GT-104S AN-GT S 30mm P2B-GT-30M AN-GT-06-30M 1-1/ P2B-GTU AN-GT / P2B-GTU AN-GT P2B-GTU / P2B-GTU-104S AN-GT mm P2B-GTU-30M AN-GT-06-30M 1-1/ P2B-GT AN-GT / P2B-GT AN-GT P2B-GT / P2B-GT AN-GT mm P2B-GT-35M AN-GT-07-35M B2-8

9 /DIMENSIONS GT NORMAL DUTY PILLOW BLOCKS Bearing Quick Reference E-Z KLEEN Weight F D lbs A B C Bolt G H J L M R# S# U V W X* Z 203 kg min. max. Dia. 1/ / /64 3-1/4 4-1/16 3/8 27/32 25/64 2-5/ /32 1-1/16 13/32 57/64 2-1/4 4-1/2 3/8 1/8 59/64 5/ mm M / / /64 3-1/4 4-1/16 3/8 27/32 17/32 2-9/ /32 1-3/16 13/32 57/64 2-1/4 4-1/2 3/8 1/8 59/ /8 1.6 (GTU) 17mm M / /32 5-1/4 1-21/64 3-3/8 4-3/16 3/8 27/32 33/ /64 1-1/2 1-5/16 31/64 63/64 2-1/4 4-1/2 1/2 1/8 1-3/ mm M / /64 5-1/2 1-13/ /16 4-1/2 3/8 27/32 37/ / /64 1-7/16 1/2 61/64 2-1/2 5 1/2 3/16 1-1/64 15/ mm M / /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 5/8 3-1/4 2-5/64 1-5/8 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-1/8 30mm M / /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 45/64 3-5/16 2-5/ /16 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-1/8 1-3/ (GTU) 1-1/ mm M / /8 6-1/2 1-47/ /16 5-7/16 1/2 15/16 45/64 3-3/4 2-3/8 1-7/8 9/16 1-1/ / /16 9/16 3/16 1-9/ mm M * Only 1 pillow block can be dowel pinned per shaft # R & S Dimensions will vary slightly depending on true shaft diameter 1-3/16 1-3/ /4 1-7/ GRIP TIGHT Adapter Ball Bearing B2-9

10 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY PILLOW BLOCKS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-1/ P2B-GT AN-GT / P2B-GT P2B-GT AN-GT mm P2B-GT-40M AN-GT-08-40M 1-5/ P2B-GT-110L AN-GT L / P2B-GT AN-GT P2B-GT / P2B-GT AN-GT mm P2B-GT-45M AN-GT-09-45M 1-15/ P2B-GT AN-GT P2B-GT P2B-GT AN-GT mm P2B-GT-50M AN-GT-10-50M P2B-GTM AN-GTM / P2B-GT AN-GT P2B-GT / P2B-GT AN-GT mm P2B-GT-55M AN-GT-11-55M 2-1/ P2B-GTM AN-GTM / P2B-GT P2B-GT AN-GT mm P2B-GT-60M AN-GT-12-60M 2-1/ P2B-GTM AN-GTM / P2B-GT P2B-GT AN-GT mm P2B-GT-70M AN-GT-14-70M 2-15/ P2B-GT AN-GT P2B-GT P2B-GT AN-GT mm P2B-GT-75M AN-GT-15-75M 2-15/ P2B-GTU AN-GT P2B-GTU P2B-GTU AN-GT (GTU) P2B-GTU-75M Assembled To Order B2-10

11 /DIMENSIONS GT NORMAL DUTY PILLOW BLOCKS E-Z KLEEN Bearing Quick Reference Weight F D lbs A B C Bolt G H J L M R# S# U V W X* Z kg min. max. Dia / /32 7-1/4 1-15/16 5-3/16 5-7/8 1/2 29/32 15/16 4-3/16 2-5/8 2-1/8 21/32 1-3/ / /32 11/16 3/ /64 1-5/ mm M / /64 7-7/ /2 6-3/16 1/2 29/32 3/4 4-9/ /64 2-1/8 21/ /64 3-3/8 6-3/4 11/16 3/16 1-9/ / / mm M / /64 8-1/8 2-1/ /16 5/8 1-1/64 3/4 4-17/32 3-1/8 2-1/4 21/ / /16 7-3/8 13/16 3/16 1-9/ mm M /64 8-7/8 2-5/16 6-3/8 7-7/16 5/8 1-7/32 7/8 4-15/ /64 2-1/2 45/64 1-7/ /16 7-7/8 13/16 3/ /32 2-3/ / mm M / /64 9-1/2 2-3/8 6-7/8 7-15/16 5/8 1-7/32 7/8 5-3/8 3-11/16 2-3/4 49/ /32 4-1/4 8-1/2 7/8 3/ /32 2-7/ mm M / / /4 2-11/16 7-1/2 8-1/2 3/4 1-5/16 15/16 6-5/ /8 1-33/64 4-7/8 9-3/4 15/16 3/ / / mm M / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/ /32 4-7/16 3-1/2 57/64 1-9/16 5-1/ /16 3/16 1-5/ mm M / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/ /32 4-7/16 3-1/4 57/ /64 5-1/ /16 3/16 1-5/ (GTU) 75mm M * Only 1 pillow block can be dowel pinned per shaft # R & S Dimensions will vary slightly depending on true shaft diameter GRIP TIGHT Adapter Ball Bearing B2-11

12 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY PILLOW BLOCKS (GTU) (GTU) Unit without Adapter Sleeve & Lock Complete Unit Adapter Sleeve & Lock Nut Assembly Nut Part No. Description Part No. Description Part No. Description P2B-GTAH AN-GT / P2B-GTAH P2B-GTAH AN-GT P2B-GTAH-17M AN-GT-03-17M P2B-GTUAH AN-GT P2B-GTUAH AN-GT P2B-GTUAH-17M AN-GT-03-17M 3/ P2B-GTAH AN-GT P2B-GTAH-04 P2B-GTAH-20M AN-GT-04-20M P2B-GTAH AN-GT P2B-GTAH AN-GT P2B-GTAH P2B-GTAH AN-GT mm P2B-GTAH-25M AN-GT-05-25M P2B-GTAH AN-GT / P2B-GTAH AN-GT P2B-GTAH-06 P2B-GTAH-104S AN-GT S P2B-GTAH-30M AN-GT-06-30M 1-1/ P2B-GTUAH AN-GT / P2B-GTUAH AN-GT P2B-GTUAH-06 P2B-GTUAH-104S AN-GT S P2B-GTUAH-30M AN-GT-06-30M 1-1/ P2B-GTAH AN-GT P2B-GTAH AN-GT / P2B-GTAH P2B-GTAH-07 AN-GT P2B-GTAH-35M Assembled to order B2-12

13 /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY PILLOW BLOCKS Bearing Quick Reference E-Z KLEEN Weight F D lbs A B C Bolt G H J L M R# S# U V W X* Z kg min. max. Dia / / /64 3-1/4 4-1/16 3/8 27/32 25/64 2-5/ /32 1-1/16 13/32 57/64 2-1/4 4-1/2 3/8 1/8 59/64 5/ mm M / / /64 3-1/4 4-1/16 3/8 27/32 17/32 2-9/ /32 1-3/16 13/32 57/64 2-1/4 4-1/2 3/8 1/8 59/ /8 1.6 (GTU) 17mm M / /32 5-1/4 1-21/64 3-3/8 4-3/16 3/8 27/32 33/ /64 1-1/2 1-5/16 31/64 63/64 2-1/4 4-1/2 1/2 1/8 1-3/ mm M / /64 5-1/2 1-13/ /16 4-1/2 3/8 27/32 37/ / /64 1-7/16 1/2 61/64 2-1/2 5 1/2 3/16 1-1/64 15/ mm M / /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 5/8 3-1/4 2-5/64 1-5/8 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-1/8 30mm M / /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 45/64 3-5/16 2-5/ /16 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-1/8 1-3/ (GTU) 1-1/ mm M / /8 6-1/2 1-47/ /16 5-7/16 1/2 15/16 45/64 3-3/4 2-3/8 1-7/8 9/16 1-1/ / /16 9/16 3/16 1-9/ mm M * Only 1 pillow block can be dowel pinned per shaft # R & S Dimensions will vary slightly depending on true shaft diameter 1-3/16 1-3/ /4 1-7/ GRIP TIGHT Adapter Ball Bearing B2-13

14 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY PILLOW BLOCKS Assembled to order Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-1/ P2B-GTAH AN-GT P2B-GTAH P2B-GTAH AN-GT P2B-GTAH-40M AN-GT-08-40M 1-5/ P2B-GTAH-110L AN-GT L 1-11/ P2B-GTAH AN-GT P2B-GTAH-09 P2B-GTAH AN-GT P2B-GTAH-45M AN-GT-09-45M 1-15/ P2B-GTAH AN-GT P2B-GTAH P2B-GTAH AN-GT P2B-GTAH-50M AN-GT-10-50M P2B-GTMAH AN-GTM / P2B-GTAH AN-GT P2B-GTAH-11 P2B-GTAH AN-GT P2B-GTAH-55M AN-GT-11-55M P2B-GTMAH AN-GTM / P2B-GTAH P2B-GTAH AN-GT P2B-GTAH-60M AN-GT-12-60M P2B-GTMAH AN-GTM / P2B-GTAH P2B-GTAH AN-GT mm P2B-GTAH-70M AN-GT-14-70M 2-15/ P2B-GTAH AN-GT P2B-GTAH P2B-GTAH AN-GT P2B-GTAH-75M AN-GT-15-75M 2-15/ P2B-GTUAH AN-GT P2B-GTUAH AN-GT P2B-GTUAH-75M AN-GT-15-75M B2-14

15 /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY PILLOW BLOCKS E-Z KLEEN Bearing Quick Reference Weight F D lbs A B C Bolt G H J L M R# S# U V W X* Z kg min. max. Dia / /32 7-1/4 1-15/16 5-3/16 5-7/8 1/2 29/32 15/16 4-3/16 2-5/8 2-1/8 21/32 1-3/ / /32 11/16 3/ /64 1-5/ mm M / /64 7-7/ /2 6-3/16 1/2 29/32 3/4 4-9/ /64 2-1/8 21/ /64 3-3/8 6-3/4 11/16 3/16 1-9/ / / mm M / /64 8-1/8 2-1/ /16 5/8 1-1/64 3/4 4-17/32 3-1/8 2-1/4 21/ / /16 7-3/8 13/16 3/16 1-9/ mm M /64 8-7/8 2-5/16 6-3/8 7-7/16 5/8 1-7/32 7/8 4-15/ /64 2-1/2 45/64 1-7/ /16 7-7/8 13/16 3/ /32 2-3/ / mm M / /64 9-1/2 2-3/8 6-7/8 7-15/16 5/8 1-7/32 7/8 5-3/8 3-11/16 2-3/4 49/ /32 4-1/4 8-1/2 7/8 3/ /32 2-7/ mm M / / /4 2-11/16 7-1/2 8-1/2 3/4 1-5/16 15/16 6-5/ /8 1-33/64 4-7/8 9-3/4 15/16 3/ / / mm M / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/ /32 4-7/16 3-1/2 57/ /64 5-1/ /16 3/16 1-5/ mm M / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/ /32 4-7/16 3-1/4 57/ /64 5-1/ /16 3/16 1-5/ (GTU) 75mm M * Only 1 pillow block can be dowel pinned per shaft # R & S Dimensions will vary slightly depending on true shaft diameter GRIP TIGHT Adapter Ball Bearing B2-15

16 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTB NORMAL DUTY PILLOW BLOCKS 203 (GT) Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1/ P2B-GT AN-GT / P2B-GT P2B-GT AN-GT mm P2B-GT-17M AN-GT-03-17M 3/ P2B-GTB AN-GT P2B-GTB-04 20mm P2B-GTB-20M AN-GT-04-20M 7/ P2B-GTB AN-GT / P2B-GTB AN-GT P2B-GTB P2B-GTB AN-GT mm P2B-GTB-25M AN-GT-05-25M 1-1/ P2B-GTB AN-GT / P2B-GTB AN-GT P2B-GTB / P2B-GTB-104S AN-GT S 30mm P2B-GTB-30M AN-GT-06-30M 1-1/ P2B-GTB AN-GT / P2B-GTB AN-GT / P2B-GTB P2B-GTB-07 AN-GT mm P2B-GTB-35M Assembled to order B2-16

17 /DIMENSIONS GTB NORMAL DUTY PILLOW BLOCKS E-Z KLEEN Bearing Quick Reference Weight F D lbs A B C Bolt G H J L M R# S# U V W X* Z kg min. max. Dia. 1/ / /64 3-1/4 4-1/16 3/8 27/32 25/64 2-5/ /32 1-1/16 13/32 57/64 2-1/4 4-1/2 3/8 1/8 59/ /8 17mm M / /32 5-1/4 1-21/64 3-3/8 4-3/16 3/8 27/32 29/ /64 1-1/2 1-1/4 31/64 63/64 2-1/4 4-1/2 1/2 1/8 1-1/64 20mm M / /64 5-1/2 1-13/ /16 4-1/2 3/8 27/32 29/ / /64 1-5/16 1/2 61/64 2-1/2 5 1/2 3/16 1-1/8 15/ mm M / /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 9/16 3-3/16 2-5/64 1-9/16 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-9/64 1-3/ / mm M / /8 6-1/2 1-47/ /16 5-7/16 1/2 15/16 41/ /16 2-3/8 1-13/16 9/16 1-1/ / /16 9/16 3/ /64 1-3/ / mm M * Only 1 pillow block can be dowel pinned per shaft # R & S Dimensions will vary slightly depending on true shaft diameter GRIP TIGHT Adapter Ball Bearing B2-17

18 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTB NORMAL DUTY PILLOW BLOCKS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-1/ P2B-GTB AN-GT / P2B-GTB P2B-GTB AN-GT mm P2B-GTB-40M AN-GT-08-40M 1-5/ P2B-GTB-110L AN-GT L / P2B-GTB AN-GT P2B-GTB / P2B-GTB AN-GT mm P2B-GTB-45M AN-GT-09-45M 1-15/ P2B-GTB AN-GT P2B-GTB P2B-GTB AN-GT mm P2B-GTB-50M AN-GT-10-50M P2B-GTB-200L AN-GTM / P2B-GTB AN-GT P2B-GTB / P2B-GTB AN-GT mm P2B-GTB-55M AN-GT-11-55M 2-1/ P2B-GTB-204L AN-GTM / P2B-GTB P2B-GTB AN-GT mm P2B-GTB-60M AN-GT-12-60M 2-15/ P2B-GTB AN-GT P2B-GTB P2B-GTB AN-GT P2B-GTB-75M Assembled to order B2-18

19 /DIMENSIONS E-Z KLEEN Bearing Quick Reference Weight F D lbs A B C Bolt G H J L M R# S# U V W X* Z kg min. max. Dia. 1-1/ /32 7-1/4 1-15/16 5-3/16 5-7/8 1/2 29/32 3/ /8 1-15/16 21/32 1-3/ / /32 11/16 3/ /64 1-5/ mm M / /64 7-7/ /2 6-3/16 1/2 29/32 11/16 4-7/ /64 2-1/16 21/ /64 3-3/8 6-3/4 11/16 3/16 1-9/ / / mm M / /64 8-1/8 2-1/ /16 5/8 1-1/64 11/ /32 3-1/8 2-3/16 21/ / /16 7-3/8 13/16 3/16 1-9/ mm M /64 8-7/8 2-5/16 6-3/8 7-7/16 5/8 1-7/32 51/64 4-7/8 3-27/64 2-7/16 45/64 1-7/ /16 7-7/8 13/16 3/ /32 2-3/ / mm M / /64 9-1/2 2-3/8 6-7/8 7-15/16 5/8 1-7/32 51/64 5-5/ / /16 49/ /32 4-1/4 8-1/2 7/8 3/ /32 2-7/16 60mm M / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/16 1-3/ /32 4-7/16 3-5/16 57/64 1-9/16 5-1/ /16 3/16 1-5/ mm M * Only 1 pillow block can be dowel pinned per shaft # R & S Dimensions will vary slightly depending on true shaft diameter GRIP TIGHT Adapter Ball Bearing B2-19

20 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTH-E EXPANSION PILLOW BLOCKS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part Part Part Description Description Description Number Number Number 205 P2B-GTH-100-E AN-GT P2B-GTH-05-E 25mm P2B-GTH-25M-E AN-GT-05-25M 1-3/ P2B-GTH-103-E AN-GT / P2B-GTH-104S-E P2B-GTH-06-E AN-GT S 30mm P2B-GTH-30M-E AN-GT-06-30M / P2B-GTH-107-E AN-GT P2B-GTH-07-E 35mm P2B-GTH-35M-E AN-GT-07-35M 1-11/ P2B-GTH-111-E AN-GT P2B-GTH-112-E P2B-GTH-09-E AN-GT mm P2B-GTH-45M-E AN-GT-09-45M 1-15/ P2B-GTH-115-E AN-GT P2B-GTH-200-E P2B-GTH-10-E AN-GT mm P2B-GTH-50M-E AN-GT-10-50M 2-3/ P2B-GTH-203-E AN-GT / P2B-GTH-204-E P2B-GTH-11-E AN-GT mm P2B-GTH-55M-E AN-GT-11-55M / P2B-GTH-207-E AN-GT P2B-GTH-12-E P2B-GTH-60M-E AN-GT-12-60M Use GTM Medium Duty Pillow Blocks for non-expansion Assembled to order B2-20

21 /DIMENSIONS GTH-E EXPANSION PILLOW BLOCKS Bearing Quick Reference Weight F D lbs A B C Bolt kg min. max. Dia. G H J /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 3/4 3-5/16 25mm M / /64 6-7/ /16 5-7/16 1/2 1 11/ /16 1-1/ mm M / /8 7-15/16 2-1/32 5-1/16 6-5/16 1/2 1-3/16 3/4 4-3/16 35mm M / /64 8-1/8 2-3/ /2 5/8 15/16 3/4 4-9/ / mm M / /64 9-1/2 2-1/ /2 5/8 1-7/16 7/8 5-3/ mm M / / / /8 7-7/8 5/8 1-7/16 1-1/16 5-5/ / mm M / / /4 3-1/4 7-3/ /16 3/4 1-5/8 1-1/16 6-1/4 60mm M T L M R# S# Total U V W Z Expansion / /16 1/2 61/64 5/32 2-7/8 5-3/4 9/16 3/16 1-1/64 25mm /16 2-5/64 1-7/8 17/32 1-5/64 3/16 3-1/8 6-1/4 11/16 3/16 1-1/8 1-1/ mm /16 2-3/8 2-1/8 9/16 1-1/16 3/ /16 7-3/8 23/32 3/16 1-9/64 35mm / /64 2-1/4 21/ /64 1/4 3-11/16 7-3/8 13/16 3/16 1-9/ /4 45mm /16 3-1/8 2-1/2 21/ /64 1/4 4-3/8 8-3/4 7/8 3/16 1-9/ mm / /64 2-3/4 45/64 1-7/32 1/4 4-3/4 9-1/2 1-1/8 3/ / /4 55mm / / / /32 1/4 5-1/4 10-1/2 1-1/4 3/ /32 60mm # R & S dimensions will vary slightly depending on true shaft Only 1 pillow block can be dowel pinned per shaft GRIP TIGHT Adapter Ball Bearing E-Z KLEEN B2-21

22 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY PILLOW BLOCKS Complete Unit Unit Without Adapter & Nut Adapter & Nut Assembly Part No. Description Part No. Description Part No. Description 205 3/ P2B-GTM P2B-GT AN-GTM P2B-GTM AN-GTM P2B-GTU-06 25mm P2B-GTM-25M AN-GTM-06-25M P2B-GTMU AN-GTM P2B-GTMU-06 (GTMU) P2B-GTMU-25M AN-GTM-06-25M 1-3/ P2B-GTM AN-GTM / P2B-GT P2B-GT AN-GT mm P2B-GTM-30M AN-GTM-07-30M / P2B-GTM AN-GTM P2B-GT-08 35mm P2B-GTM-35M AN-GTM-08-35M / P2B-GTM AN-GTM P2B-GT-09 40mm P2B-GTM-40M AN-GTM-09-40M 1-11/ P2B-GTM AN-GTM / P2B-GTM P2B-GT AN-GTM mm P2B-GTM-45M AN-GTM-10-45M 1-11/ P2B-GTMU AN-GTM P2B-GTMU P2B-GTU AN-GTM (GTMU) P2B-GTMU-45M Assembled to order B2-22

23 /DIMENSIONS GTM MEDIUM DUTY PILLOW BLOCKS Bearing Quick Reference E-Z KLEEN Weight F D lbs A B C Bolt G H J L M R# S# U V W X@ Z kg min. max. Dia /4 2.4 (GTMU) /64 5-1/2 1-13/ /16 4-1/2 3/8 27/32 37/64 2-5/ /64 1-7/16 1/2 61/64 2-1/2 5 1/2 3/16 1-1/ M /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 5/8 3-1/4 2-5/ /16 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-1/8 25mm M /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 11/16 3-5/16 2-5/64 1-3/4 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-1/8 25mm M / /8 6-1/2 1-47/ /16 5-7/16 1/2 15/16 45/64 3-3/4 2-3/8 1-7/8 9/16 1-1/ / /16 9/16 3/16 1-9/64 1-1/ mm M / /32 7-1/4 1-15/16 5-3/16 5-7/8 1/2 29/32 15/16 4-3/16 2-5/8 2-1/8 21/32 1-3/ / /32 11/16 3/ /64 35mm M / /64 7-7/ /2 6-3/16 1/2 29/32 3/4 4-9/ /64 2-1/8 21/ /64 3-3/8 6-3/4 11/16 3/16 1-9/32 40mm M / /64 8-1/8 2-1/ /16 5/8 1-1/64 3/4 4-17/32 3-1/8 2-1/4 21/ / /16 7-3/8 13/16 3/16 1-9/32 1-3/ mm M / /64 8-1/8 2-1/ /16 5/8 1-1/64 13/ /32 3-1/8 2-5/16 21/ / /16 7-3/8 13/16 3/16 1-9/ / (GTMU) 45mm M #R & S dimensions will vary slightly depending on true shaft Only 1 pillow block can be dowel pinned per shaft GRIP TIGHT Adapter Ball Bearing B2-23

24 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY PILLOW BLOCKS Complete Unit Unit Without Adapter & Nut Adapter & Nut Assembly Part No. Description Part No. Description Part No. Description 1-15/ P2B-GTM AN-GTM P2B-GTM P2B-GT AN-GTM mm P2B-GTM-50M AN-GTM-11-50M 2-3/ P2B-GTM AN-GTM / P2B-GTM P2B-GT AN-GTM mm P2B-GTM-55M AN-GTM-12-55M 2-7/ P2B-GTM AN-GTM / P2B-GTM P2B-GT AN-GTM mm P2B-GTM-60M AN-GTM-14-60M 65mm P2B-GTM-65M AN-GTM-14-65M / P2B-GTM AN-GTM P2B-GT-15 70mm P2B-GTM-70M AN-GTM-15-70M 2-15/ P2B-GTM AN-GTM P2B-GTM P2B-GT AN-GTM mm P2B-GTM-75M AN-GTM-16-75M 3-7/ P2B-GTM AN-GTM / P2B-GTM P2B-GT AN-GTM mm P2B-GTM-85M Assembled to order B2-24

25 /DIMENSIONS GTM MEDIUM DUTY PILLOW BLOCKS E-Z KLEEN Bearing Quick Reference Weight F D lbs A B C Bolt G H J L M R# S# U V W X@ Z kg min. max. Dia / /64 8-7/8 2-5/16 6-3/8 7-7/16 5/8 1-7/32 7/8 4-15/ /64 2-1/2 45/64 1-7/ /16 7-7/8 13/16 3/ / mm M / /64 9-1/2 2-3/8 6-7/8 7-15/16 5/8 1-7/32 7/8 5-3/8 3-11/16 2-3/4 49/ /32 4-1/4 8-1/2 7/8 3/ /32 2-1/ mm M / / /4 2-11/16 7-1/2 8-1/2 3/4 1-5/16 15/16 6-5/ /8 1-33/64 4-7/8 9-3/4 15/16 3/ /32 2-1/ mm mm M / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/ /32 4-7/16 3-1/2 57/64 1-9/16 5-1/ /16 3/16 1-5/ mm M / / / /2 9-1/2 7/8 1-7/16 1-1/4 6-31/ /16 3-1/2 29/ /64 5-1/ /32 3/16 1-5/ mm M / / /8 10-5/ /8 7/8 1-19/32 1-5/ / /64 6-9/ /8 1-3/16 3/ / /2 85mm M #R & S dimensions will vary slightly depending on true shaft Only 1 pillow block can be dowel pinned per shaft GRIP TIGHT Adapter Ball Bearing B2-25

26 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTMAH AIR HANDLING MEDIUM DUTY PILLOW BLOCKS Complete Unit Unit Without Adapter & Nut Adapter & Nut Assembly Part No. Description Part No. Description Part No. Description 205 P2B-GTMAH P2B-GTAH AN-GTM P2B-GTMAH AN-GTM P2B-GTUAH-06 P2B-GTMAH-25M AN-GTM-06-25M P2B-GTMUAH AN-GTM P2B-GTMUAH-06 (GTMU) P2B-GTMUAH-25M AN-GTM-06-25M 1-3/ P2B-GTMAH AN-GTM P2B-GTAH P2B-GTAH AN-GT mm P2B-GTMAH-30M AN-GTM-07-30M / P2B-GTMAH AN-GTM P2B-GTAH-08 35mm P2B-GTMAH-35M AN-GTM-08-35M 209 P2B-GTMAH AN-GTM P2B-GTAH-09 40mm P2B-GTMAH-40M AN-GTM-09-40M 1-11/ P2B-GTMAH AN-GTM P2B-GTMAH P2B-GTAH AN-GTM mm P2B-GTMAH-45M AN-GTM-10-45M / P2B-GTMUAH AN-GTM (GTMU) P2B-GTMUAH P2B-GTUAH AN-GTM P2B-GTMUAH-45M Assembled to order B2-26

27 /DIMENSIONS GTMAH AIR HANDLING MEDIUM DUTY PILLOW BLOCKS Bearing Quick Reference E-Z KLEEN Weight F D lbs A B C Bolt G H J L M R# S# U V W X Z kg min. max. Dia / /64 5-1/2 1-13/ /16 4-1/2 3/8 27/32 37/64 2-5/ /64 1-7/16 1/2 61/64 2-1/2 5 1/2 3/16 1-1/ /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 5/8 3-1/4 2-5/64 1-5/8 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-1/8 25mm M /64 6-1/4 1-47/64 4-1/4 5 1/2 15/16 11/16 3-5/16 2-5/64 1-3/4 17/32 1-5/64 2-7/8 5-3/4 9/16 3/16 1-1/8 (GTMU) 25mm M / /8 6-1/2 1-47/ /16 5-7/16 1/2 15/16 45/64 3-3/4 2-3/8 1-7/8 9/16 1-1/ / /16 9/16 3/16 1-9/ /4 30mm M / /32 7-1/4 1-15/16 5-3/16 5-7/8 1/2 29/32 15/16 4-3/16 2-5/8 2-1/8 21/32 1-3/ / /32 11/16 3/ /64 35mm M / /64 7-7/ /2 6-3/16 1/2 29/32 3/4 4-9/ /64 2-1/8 21/ /64 3-3/8 6-3/4 11/16 3/16 1-9/ mm M / /64 8-1/8 2-1/ /16 5/8 1-1/64 3/4 4-17/32 3-1/8 2-1/4 21/ / /16 7-3/8 13/16 3/16 1-9/ /4 45mm M / /64 8-1/8 2-1/ /16 5/8 1-1/64 13/ /32 3-1/8 2-5/16 21/ / /16 7-3/8 13/16 3/16 1-9/ /4 (GTMU) 45mm M #R & S dimensions will vary slightly depending on true shaft diameter GRIP TIGHT Adapter Ball Bearing B2-27

28 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTMAH AIR HANDLING MEDIUM DUTY PILLOW BLOCKS Complete Unit Unit Without Adapter & Nut Adapter & Nut Assembly Part No. Description Part No. Description Part No. Description 1-15/ P2B-GTMAH AN-GTM P2B-GTMAH P2B-GTAH AN-GTM mm P2B-GTMAH-50M AN-GTM-11-50M 2-3/ P2B-GTMAH AN-GTM P2B-GTMAH P2B-GTAH AN-GTM mm P2B-GTMAH-55M AN-GTM-12-55M 2-7/ P2B-GTMAH AN-GTM / P2B-GTMAH P2B-GTAH AN-GTM mm P2B-GTMAH-65M AN-GTM-14-65M / P2B-GTMAH AN-GTM P2B-GTAH-15 70mm P2B-GTMAH-70M AN-GTM-15-70M 2-15/ P2B-GTMAH AN-GTM P2B-GTMAH P2B-GTAH AN-GTM mm P2B-GTMAH-75M AN-GTM-16-75M 3-7/ P2B-GTMAH AN-GTM P2B-GTMAH P2B-GTAH AN-GTM mm P2B-GTMAH-85M Assembled to order B2-28

29 /DIMENSIONS GTMAH AIR HANDLING MEDIUM DUTY PILLOW BLOCKS Bearing Quick Reference E-Z KLEEN Weight F D lbs A B C Bolt G H J L M R# S# U V W X Z kg min. max. Dia. 1-15/ /64 8-7/8 2-5/16 6-3/8 7-7/16 5/8 1-7/32 7/8 4-15/ /64 2-1/2 45/64 1-7/ /16 7-7/8 13/16 3/ / mm M / /64 9-1/2 2-3/8 6-7/8 7-15/16 5/8 1-7/32 7/8 5-3/8 3-11/16 2-3/4 49/ /32 4-1/4 8-1/2 7/8 3/ / /4 55mm M / / /4 2-11/16 7-1/2 8-1/2 3/4 1-5/16 15/16 6-5/ /8 1-33/64 4-7/8 9-3/4 15/16 3/ / /2 65mm M / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/ /32 4-7/16 3-1/2 57/64 1-9/16 5-1/ /16 3/16 1-5/ mm M / / / /2 9-1/2 7/8 1-7/16 1-1/4 6-31/ /16 3-1/2 29/ /64 5-1/ /32 3/16 1-5/ mm M / / /8 10-5/ /8 7/8 1-19/32 1-5/ / /64 6-9/ /8 1-3/16 3/ / /2 85mm M #R & S dimensions will vary slightly depending on true shaft diameter GRIP TIGHT Adapter Ball Bearing B2-29

30 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY TAPPED BASE PILLOW BLOCKS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 204 3/ TB-GT TB-GT AN-GT mm TB-GT-20M TB-GT-04M AN-GT-04-20M 7/ TB-GT AN-GT / TB-GT TB-GT AN-GT TB-GT AN-GT mm TB-GT-25M TB-GT-05M AN-GT-05-25M 1-1/ TB-GT AN-GT / TB-GT TB-GT AN-GT / TB-GT-104S AN-GT S 30mm TB-GT-30M TB-GT-06M AN-GT-06-30M 1-1/ TB-GT AN-GT / TB-GT TB-GT AN-GT / TB-GT AN-GT mm TB-GT-35M TB-GT-07M AN-GT-07-35M 1-1/ TB-GT TB-GT AN-GT TB-GT AN-GT mm TB-GT-40M TB-GT-08M AN-GT-08-40M 1-5/ TB-GT-110L AN-GT L / TB-GT TB-GT AN-GT / TB-GT AN-GT mm TB-GT-45M TB-GT-09M AN-GT-09-45M 1-15/ TB-GT TB-GT AN-GT TB-GT AN-GT mm TB-GT-50M TB-GT-10M Assemble to order B2-30

31 /DIMENSIONS GT NORMAL DUTY TAPPED BASE PILLOW BLOCKS Bearing Quick Reference E-Z KLEEN Weight R* lbs A B C D J L M N UNC- S# Z kg Thread 3/ /32 2-7/8 1-1/ /16 1-1/2 1-5/16 1/2 3/ /64 1-3/ mm M8 x / / / / /64 1-7/16 1/2 3/ /64 1-1/64 15/ mm M10 x / / / /8 2-5/ /16 5/8 7/ /64 1-1/8 30mm M10 x / /8 4-1/4 1-7/8 3-1/4 3-3/4 2-3/8 1-7/8 3/4 1/ /16 1-9/ mm M10 x / /64 4-5/8 1-7/8 3-1/2 3-15/16 2-5/8 1-15/16 3/4 1/ / / / mm M12 x / / /4 4-1/4 2-55/64 2-1/8 3/4 1/ /16 1-9/ mm M12 x / /64 5-1/ /8 3-1/8 2-1/4 7/8 5/ /64 1-9/ mm M16 x #S dimension will vary slightly depending on true shaft diameter * Mounting surface bolt holes on all GRIP TIGHT Tapped Base Units must have at least 1/16 bolt clearance 1-3/16 1-3/8 1-11/ /4 1-7/16 1-3/ GRIP TIGHT Adapter Ball Bearing B2-31

32 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY 2 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1/ F2B-GT AN-GT / F2B-GT F2B-GT AN-GT mm F2B-GT-17M AN-GT-03-17M 204 3/ F2B-GT AN-GT F2B-GT-04 20mm F2B-GT-20M AN-GT-04-20M 7/ F2B-GT AN-GT / F2B-GT AN-GT F2B-GT F2B-GT AN-GT mm F2B-GT-25M AN-GT-05-25M 1-1/ F2B-GT AN-GT / F2B-GT AN-GT F2B-GT / F2B-GT-104S AN-GT S 30mm F2B-GT-30M AN-GT-06-30M 1-1/ F2B-GT AN-GT / F2B-GT AN-GT F2B-GT / F2B-GT AN-GT mm F2B-GT-35M Assembled to order. B2-32

33 /DIMENSIONS GT NORMAL DUTY 2 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt H J L M N Z kg Dia. 1/ /64 3-7/8 1-27/64 3 3/8 3/8 39/ /32 2-1/8 1-1/8 1-29/ / mm M / / / / /32 3/8 1/2 11/16 1-1/2 2-3/8 1-1/2 1-43/ mm M / /64 4-7/8 1-35/ /64 7/16 1/2 21/ /64 2-3/4 1-7/ /64 15/ mm M / /64 5-9/ / /32 7/16 1/2 11/16 2-5/64 3-1/8 1-9/16 1-3/4 30mm M / /8 6-1/8 1-25/32 5-1/8 1/2 9/16 41/64 2-3/8 3-3/4 1-27/ / mm M #C dimension will vary slightly depending on true shaft diameter. 1-3/16 1-3/ /4 1-7/ GRIP TIGHT Adapter Ball Bearing B2-33

34 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY 2 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-1/ F2B-GT AN-GT / F2B-GT F2B-GT AN-GT mm F2B-GT-40M AN-GT-08-40M 1-5/ F2B-GT-110L AN-GT L / F2B-GT AN-GT F2B-GT / F2B-GT AN-GT mm F2B-GT-45M AN-GT-09-45M 1-15/ F2B-GT AN-GT F2B-GT F2B-GT AN-GT mm F2B-GT-50M AN-GT-10-50M F2B-GTM AN-GTM / F2B-GT AN-GT F2B-GT / F2B-GT AN-GT mm F2B-GT-55M AN-GT-11-55M 2-1/ F2B-GTM AN-GTM / F2B-GT F2B-GT AN-GT mm F2B-GT-60M Assembled to order. B2-34

35 /DIMENSIONS GT NORMAL DUTY 2 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt H J L M N Z kg Dia. 1-1/ /32 6-3/4 1-31/ /32 1/2 9/16 43/64 2-5/8 4-1/8 1-53/64 2-7/ / mm M / /64 7-1/ /32 1/2 5/8 11/ /64 4-3/8 1-29/32 2-3/ / / mm M / /64 7-7/16 2-3/64 6-3/16 1/2 5/8 21/32 3-1/8 4-9/16 2-1/32 2-1/ mm M /64 8-5/8 2-5/32 7-1/4 5/8 11/16 11/ /64 5-1/4 2-17/64 2-9/ / / mm M / / /16 2-5/ /64 7/8 13/16 23/ /16 5-1/2 2-15/32 2-7/ / mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-35

36 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY 2 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description F2B-GTAH AN-GT / F2B-GTAH F2B-GTAH AN-GT F2B-GTAH-17M AN-GT-03-17M 204 F2B-GTAH F2B-GTAH-04 F2B-GTAH-20M AN-GT-04-20M F2B-GTAH AN-GT F2B-GTAH F2B-GTAH-05 F2B-GTAH AN-GT F2B-GTAH-25M AN-GT-05-25M F2B-GTAH AN-GT F2B-GTAH AN-GT F2B-GTAH-06 F2B-GTAH-104S AN-GT S F2B-GTAH-30M AN-GT-06-30M F2B-GTAH AN-GT F2B-GTAH AN-GT F2B-GTAH-07 F2B-GTAH AN-GT F2B-GTAH-35M Assembled to order. B2-36

37 /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY 2 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt H J L M N Z kg Dia. 1/ /64 3-7/8 1-27/64 3 3/8 3/8 39/ /32 2-1/8 1-1/8 1-29/ / mm M / / / / /32 3/8 1/2 11/16 1-1/2 2-3/8 1-1/2 1-43/ mm M / /64 4-7/8 1-35/ /64 7/16 1/2 21/ /64 2-3/4 1-7/ /64 15/ mm M / /64 5-9/ / /32 7/16 1/2 11/16 2-5/64 3-1/8 1-9/16 1-3/4 1-3/ / mm M / /8 6-1/8 1-25/32 5-1/8 1/2 9/16 41/64 2-3/8 3-3/4 1-27/ /64 1-3/ / mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-37

38 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY 2 BOLT FLANGE BEARINGS Adapter Sleeve & Lock Nut Complete Unit Unit without Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description F2B-GTAH AN-GT F2B-GTAH AN-GT F2B-GTAH-40M AN-GT-08-40M F2B-GTAH-110L AN-GT L 209 F2B-GTAH F2B-GTAH-09 F2B-GTAH AN-GT F2B-GTAH-45M AN-GT-09-45M F2B-GTAH AN-GT F2B-GTAH AN-GT F2B-GTAH-50M AN-GT-10-50M F2B-GTMAH AN-GTM F2B-GTAH F2B-GTAH-11 F2B-GTAH AN-GT F2B-GTAH-55M AN-GT-11-55M F2B-GTMAH AN-GTM F2B-GTAH AN-GT F2B-GTAH-60M Assembled to order. B2-38

39 /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY 2 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt H J L M N Z kg Dia. 1-1/ /32 6-3/4 1-31/ /32 1/2 9/16 43/64 2-5/8 4-1/8 1-53/64 2-7/ / mm M / /64 7-1/ /32 1/2 5/8 11/ /64 4-3/8 1-29/32 2-3/ / / mm M / /64 7-7/16 2-3/64 6-3/16 1/2 5/8 21/32 3-1/8 4-9/16 2-1/32 2-1/ mm M /64 8-5/8 2-5/32 7-1/4 5/8 11/16 11/ /64 5-1/4 2-17/64 2-9/ / / mm M / / /16 2-5/ /64 7/8 13/16 23/ /16 5-1/2 2-15/32 2-7/ / mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-39

40 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY 2 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 205 3/ F2B-GTM F2B-GT AN-GTM F2B-GTM AN-GTM F2B-GT-06 25mm F2B-GTM-25M AN-GTM-06-25M 1-3/ F2B-GTM AN-GTM / F2B-GT F2B-GT AN-GT mm F2B-GTM-30M AN-GTM-07-30M / F2B-GTM AN-GTM F2B-GT-08 35mm F2B-GTM-35M AN-GTM-08-35M 1-1/ F2B-GTM AN-GTM / F2B-GT-110L F2B-GT-09 40mm F2B-GTM-40M AN-GTM-09-40M 1-11/ F2B-GTM AN-GTM / F2B-GTM F2B-GT AN-GTM mm F2B-GTM-405M AN-GTM-10-45M 1-15/ F2B-GTM AN-GTM F2B-GTM F2B-GT AN-GTM mm F2B-GTM-50M AN-GTM-11-50M F2B-GTM AN-GTM / F2B-GTM F2B-GT AN-GTM mm F2B-GTM-55M Assembled to order. B2-40

41 /DIMENSIONS GTM MEDIUM DUTY 2 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt kg Dia. H J L M N Z 205 3/ /64 4-7/8 1-35/ /64 7/16 1/2 19/ /64 2-3/4 1-7/ / /64 5-9/ / /32 7/16 1/2 19/32 2-5/64 3-1/8 1-9/16 1-3/4 25mm M / /8 6-1/8 1-25/32 5-1/8 1/2 9/16 35/64 2-3/8 3-3/4 1-27/ / / mm M / /32 6-3/4 1-31/ /32 1/2 9/16 37/64 2-5/8 4-1/8 1-53/64 2-7/32 35mm M / /64 7-1/ /32 1/2 5/8 9/ /64 4-3/8 1-29/32 2-3/ / mm M / /64 7-7/16 2-3/64 6-3/16 1/2 5/8 17/32 3-1/8 4-9/16 2-1/32 2-1/ / mm M / /64 8-5/8 2-5/32 7-1/4 5/8 11/16 17/ /64 5-1/4 2-17/64 2-9/ mm M / / /16 2-5/ /64 7/8 13/16 9/ /16 5-1/2 2-15/32 2-7/ / mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-41

42 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT LFT NORMAL DUTY 2 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter & Nut Adapter & Nut Assembly Part No. Description Part No. Description Part No. Description 1/ LFT-GT AN-GT / LFT-GT LFT-GT AN-GT LFT-GT-17M AN-GT-03-17M 204 3/ LFT-GT AN-GT LFT-GT-04 20mm LFT-GT-20M AN-GT-04-20M 7/ LFT-GT AN-GT / LFT-GT AN-GT LFT-GT LFT-GT AN-GT mm LFT-GT-25M AN-GT-05-25M 1-1/ LFT-GT AN-GT / LFT-GT AN-GT LFT-GT / LFT-GT-104S AN-GT S LFT-GT-30M AN-GT-06-30M 1-1/ LFT-GT AN-GT / LFT-GT AN-GT LFT-GT / LFT-GT AN-GT LFT-GT-35M Assembled to order. B2-42

43 /DIMENSIONS GT LFT NORMAL DUTY 2 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight lbs A B C# D G H J L M N* kg 1/ /64 3-3/ /64 2-1/2 9/32 3/8 39/ /32 2-1/8 1-15/ / mm / /32 3-9/ / /16 11/32 27/64 5/8 1-1/2 2-3/8 1-11/ mm / /64 3-3/4 1-7/ /32 27/64 19/ /64 2-5/8 1-7/16 15/ mm / /64 4-7/16 1-5/8 3-9/16 13/32 15/32 19/32 2-5/64 3-1/4 1-23/32 30mm / /8 4-13/ / /16 13/32 1/2 35/64 2-3/8 3-1/2 1-53/ mm #C dimension will vary slightly depending on true shaft diameter 1-3/16 1-3/ /4 1-7/ GRIP TIGHT Adapter Ball Bearing B2-43

44 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY FLANGED BRACKETED BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 204 3/ FB-GT FB-GT AN-GT / FB-GT AN-GT / FB-GT FB-GT AN-GT FB-GT AN-GT / FB-GT AN-GT / FB-GT FB-GT AN-GT / FB-GT-104S AN-GT S 1-1/ FB-GT AN-GT / FB-GT FB-GT AN-GT / FB-GT AN-GT / FB-GT AN-GT FB-GT FB-GT AN-GT B2-44

45 /DIMENSIONS GT NORMAL DUTY FLANGED BRACKETED BEARINGS Bearing Quick Reference E-Z KLEEN F Weight A B C# D E Bolt G H I J K L M Z lbs Dia / /32 4-1/4 1-19/32 1-1/2 1-11/16 3/8 7/8 5/ /2 63/64 1-1/2 2-3/8 1-21/2 7/ / /64 4-3/4 1-11/16 1-5/8 1-13/16 3/8 1-1/8 3/8 3-3/8 2-3/4 1-7/ /64 2-1/2 1-3/ / / /64 5-3/8 1-25/32 1-7/8 2-1/16 3/8 1-1/4 3/8 3-3/4 3-1/4 1-1/8 2-5/64 2-3/4 1-53/64 1-1/ / / /8 6-1/8 1-57/ /8 1/2 1-1/4 1/2 4-1/4 3-3/4 1-5/16 2-3/8 3-1/4 1-31/32 1-7/ / /64 7-1/2 2-5/64 2-3/4 2-15/16 1/2 1-5/8 1/2 5-3/16 4-5/8 1-1/2 3-1/ / #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-45

46 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT LF NORMAL DUTY 3 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1/ LF-GT AN-GT / LF-GT LF-GT AN-GT LF-GT-17M AN-GT-03-17M 3/ LF-GT AN-GT LF-GT-04 LF-GT-20M AN-GT-04-20M 7/ LF-GT AN-GT / LF-GT AN-GT LF-GT LF-GT AN-GT LF-GT-25M AN-GT-05-25M 1-1/ LF-GT AN-GT / LF-GT AN-GT LF-GT / LF-GT-104S AN-GT S LF-GT-30M AN-GT-06-30M 1-1/ LF-GT AN-GT / LF-GT AN-GT LF-GT / LF-GT AN-GT LF-GT-35M AN-GT-07-35M B2-46

47 /DIMENSIONS GT LF NORMAL DUTY 3 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight lbs A B C# D G H J L M N* kg 1/ /64 3-3/ /64 2-1/2 9/32 3/8 39/ / /32 1-7/ / mm / /32 3-9/ / /16 23/64 27/64 5/8 1-1/2 1-25/ / mm / /64 3-3/4 1-7/ /32 27/64 19/ /64 1-7/8 1-47/64 15/ mm / /64 4-7/16 1-5/8 3-9/16 13/32 15/32 19/32 2-5/64 2-7/32 2-3/64 30mm / /8 4-13/ / /16 13/32 1/2 35/64 2-3/8 2-13/ / mm # C dimension will vary slightly depending on true shaft diameter 1-3/16 1-3/ /4 1-7/ GRIP TIGHT Adapter Ball Bearing B2-47

48 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY 4 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1/ F4B-GT AN-GT / F4B-GT F4B-GT AN-GT mm F4B-GT-17M AN-GT-03-17M 204 3/ F4B-GT AN-GT F4B-GT-04 20mm F4B-GT-20M AN-GT-04-20M 7/ F4B-GT AN-GT / F4B-GT AN-GT F4B-GT F4B-GT AN-GT mm F4B-GT-25M AN-GT-05-25M 1-1/ F4B-GT AN-GT / F4B-GT AN-GT F4B-GT / F4B-GT-104S AN-GT S 30mm F4B-GT-30M AN-GT-06-30M 1-1/ F4B-GT AN-GT / F4B-GT AN-GT F4B-GT / F4B-GT AN-GT mm F4B-GT-35M to order B2-48

49 /DIMENSIONS GT NORMAL DUTY 4 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt H J L N Z kg Dia. 1/ / /64 2-1/8 3/8 7/16 39/ / / / / mm M / /32 3-3/8 1-39/64 2-1/2 3/8 7/16 11/16 1-1/2 1-15/ / mm M / /64 3-3/4 1-35/64 2-3/4 7/16 1/2 21/ /64 2-1/ /64 15/ mm M / /64 4-1/4 1-45/64 3-1/4 7/16 1/2 11/16 2-5/64 2-3/16 1-3/4 30mm M / /8 4-3/4 1-49/64 3-5/8 1/2 9/16 41/64 2-3/8 2-7/ / mm M #C dimension will vary slightly depending on true shaft diameter. 1-3/16 1-3/ /4 1-7/ GRIP TIGHT Adapter Ball Bearing B2-49

50 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY 4 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-1/ F4B-GT AN-GT / F4B-GT F4B-GT AN-GT mm F4B-GT-40M AN-GT-08-40M 1-5/ F4B-GT-110L AN-GT L / F4B-GT AN-GT F4B-GT / F4B-GT AN-GT mm F4B-GT-45M AN-GT-09-45M 1-15/ F4B-GT AN-GT F4B-GT F4B-GT AN-GT mm F4B-GT-50M AN-GT-10-50M F4B-GTM AN-GTM / F4B-GT AN-GT F4B-GT / F4B-GT AN-GT mm F4B-GT-55M AN-GT-11-55M 2-1/ F4B-GTM AN-GTM / F4B-GT F4B-GT AN-GT mm F4B-GT-60M AN-GT-12-60M 2-1/ F4B-GTM AN-GTM / F4B-GT F4B-GT AN-GT mm F4B-GT-70M AN-GT-14-70M 2-15/ F4B-GT AN-GT F4B-GT F4B-GT AN-GT mm F4B-GT-75M to order B2-50

51 /DIMENSIONS GT NORMAL DUTY 4 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt H J L N Z kg Dia. 1-1/ /32 5-1/8 1-31/32 4 1/2 9/16 43/64 2-5/8 2-3/8 2-7/ / mm M / /64 5-3/ /8 1/2 5/8 11/ /64 2-3/4 2-3/ / / mm M / /64 5-5/8 2-3/64 4-3/8 1/2 5/8 21/32 3-1/8 2-7/8 2-1/ mm M /64 6-1/2 2-9/64 5-1/8 5/8 11/16 11/ /64 3-1/4 2-9/ / / mm M / /64 6-7/8 2-5/16 5-5/8 5/8 11/16 23/ /16 3-1/2 2-7/ / mm M / /64 7-3/8 2-53/64 5-7/8 5/8 11/16 23/ / / / mm M / /64 7-3/4 3-3/16 6 3/4 1 51/64 4-7/16 3-7/8 3-3/ mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-51

52 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY 4 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description F4B-GTAH AN-GT F4B-GTAH AN-GT F4B-GTAH-17M AN-GT-03-17M 204 F4B-GTAH AN-GT F4B-GTAH-20M AN-GT-04-20M F4B-GTAH AN-GT F4B-GTAH AN-GT F4B-GTAH F4B-GTAH AN-GT F4B-GTAH-25M AN-GT-05-25M F4B-GTAH AN-GT / F4B-GTAH AN-GT F4B-GTAH-06 F4B-GTAH-104S AN-GT S F4B-GTAH-30M AN-GT-06-30M F4B-GTAH AN-GT F4B-GTAH AN-GT F4B-GTAH / F4B-GTAH AN-GT F4B-GTAH-35M to order B2-52

53 /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY 4 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt H J L N Z kg Dia. 1/ / /64 2-1/8 3/8 7/16 39/ / / / / mm M / /32 3-3/8 1-39/64 2-1/2 3/8 7/16 5/8 1-1/2 1-15/ / mm M / /64 3-3/4 1-35/64 2-3/4 7/16 1/2 19/ /64 2-1/ /64 15/ mm M / /64 4-1/4 1-45/64 3-1/4 7/16 1/2 19/32 2-5/64 2-3/16 1-3/4 30mm M / /8 4-3/4 1-49/64 3-5/8 1/2 9/16 17/32 2-3/8 2-7/ / mm M #C dimension will vary slightly depending on true shaft diameter. 1-3/16 1-3/ /4 1-7/ GRIP TIGHT Adapter Ball Bearing B2-53

54 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY 4 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description F4B-GTAH AN-GT F4B-GTAH F4B-GTAH AN-GT F4B-GTAH-40M AN-GT-08-40M F4B-GTAH-110L AN-GT L / F4B-GTAH AN-GT F4B-GTAH / F4B-GTAH AN-GT F4B-GTAH-45M AN-GT-09-45M 1-15/ F4B-GTAH AN-GT F4B-GTAH F4B-GTAH AN-GT mm F4B-GTAH-50M AN-GT-10-50M F4B-GTMAH AN-GTM / F4B-GTAH AN-GT F4B-GTAH-11 F4B-GTAH AN-GT F4B-GTAH-55M AN-GT-11-55M F4B-GTMAH AN-GTM / F4B-GTAH F4B-GTAH AN-GT F4B-GTAH-60M AN-GT-12-60M F4B-GTMAH AN-GTM F4B-GTAH F4B-GTAH AN-GT F4B-GTAH-70M AN-GT-14-70M 2-15/ F4B-GTAH AN-GT F4B-GTAH F4B-GTAH AN-GT F4B-GTAH-75M to order B2-54

55 /DIMENSIONS GTAH AIR HANDLING NORMAL DUTY 4 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D Bolt kg Dia. H J L N Z 1-1/ /32 5-1/8 1-31/32 4 1/2 9/16 43/64 2-5/8 2-3/8 2-7/ / mm M / /64 5-3/ /8 1/2 5/8 11/ /64 2-3/4 2-3/ / / mm M / /64 5-5/8 2-3/64 4-3/8 1/2 5/8 21/32 3-1/8 2-7/8 2-1/ mm M /64 6-1/2 2-9/64 5-1/8 5/8 11/16 11/ /64 3-1/4 2-9/ / / mm M / /64 6-7/8 2-5/16 5-5/8 5/8 11/16 23/ /16 3-1/2 2-7/ / mm M / /64 7-3/8 2-53/64 5-7/8 5/8 11/16 23/ / / / mm M / /64 7-3/4 3-3/16 6 3/4 1 51/64 4-7/16 3-7/8 3-3/ mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-55

56 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY 4 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 205 3/ F4B-GTM F4B-GT AN-GTM F4B-GTM AN-GTM F4B-GT-06 25mm F4B-GTM-25M AN-GTM-06-25M 1-3/ F4B-GTM AN-GTM / F4B-GT F4B-GT AN-GT mm F4B-GTM-30M AN-GTM-07-30M / F4B-GTM AN-GTM F4B-GT-08 35mm F4B-GTM-35M AN-GTM-08-35M / F4B-GTM AN-GTM F4B-GT-09 40mm F4B-GTM-40M AN-GTM-09-40M 1-11/ F4B-GTM AN-GTM / F4B-GTM F4B-GT AN-GTM mm F4B-GTM-45M to order B2-56

57 /DIMENSIONS GTM MEDIUM DUTY 4 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight lbs. kg F A B C# D Bolt H J L N Z Dia / /64 3-3/4 1-35/64 2-3/4 7/16 1/2 21/ /64 2-1/ / /64 4-1/4 1-45/64 3-1/4 7/16 1/2 11/16 2-5/64 2-3/16 1-3/4 25mm M / /8 4-3/4 1-49/64 3-5/8 1/2 9/16 41/64 2-3/8 2-7/ / / mm M / /32 5-1/8 1-31/32 4 1/2 9/16 43/64 2-5/8 2-3/8 2-7/32 35mm M / /64 5-3/ /8 1/2 5/8 11/ /64 2-3/4 2-3/32 40mm M / /64 5-5/8 2-3/64 4-3/8 1/2 5/8 21/32 3-1/8 2-7/8 2-1/ / mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-57

58 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY 4 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-15/ F4B-GTM AN-GTM F4B-GTM F4B-GT AN-GTM mm F4B-GTM-50M AN-GTM-11-50M 2-3/ F4B-GTM AN-GTM / F4B-GTM F4B-GT AN-GTM mm F4B-GTM-55M AN-GTM-12-55M 2-7/ F4B-GTM AN-GTM / F4B-GTM F4B-GT AN-GTM mm F4B-GTM-65M AN-GTM-14-65M / F4B-GTM AN-GTM F4B-GT-15 70mm F4B-GTM-70M AN-GTM-15-70M 2-15/ F4B-GTM AN-GTM F4B-GTM F4B-GT AN-GTM mm F4B-GTM-75M AN-GTM-16-75M 3-7/ F4B-GTM AN-GTM / F4B-GTM F4B-GT AN-GTM mm F4B-GTM-85M to order B2-58

59 /DIMENSIONS GTM MEDIUM DUTY 4 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs. A B C# D Bolt kg Dia. H J L N Z 1-15/ /64 6-1/2 2-9/64 5-1/8 5/8 11/16 11/ /64 3-1/4 2-9/ mm M / /64 6-7/8 2-5/16 5-5/8 5/8 11/16 23/ /16 3-1/2 2-7/ / mm M / /64 7-3/8 2-53/64 5-7/8 5/8 11/16 23/ / / / mm M / /64 7-3/4 3-3/16 6 3/4 1 51/64 4-7/16 3-7/8 3-3/64 70mm M / /16 7-3/4 3-3/8 6 3/4 7/8 57/ /16 4-9/ / mm M / /64 8-7/ /64 6-3/4 3/ /16 4-5/8 3-39/ /2 85mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-59

60 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTMAH AIR HANDLING MEDIUM DUTY 4 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 205 F4B-GTMAH F4B-GTAH AN-GTM F4B-GTMAH AN-GTM F4B-GTAH-06 F4B-GTMAH-25M AN-GTM-06-25M 1-3/ F4B-GTMAH AN-GTM F4B-GTAH F4B-GTAH AN-GT F4B-GTMAH-30M AN-GTM-07-30M / F4B-GTMAH-107 F4B-GTAH AN-GTM F4B-GTMAH-35M AN-GTM-08-35M 209 F4B-GTMAH AN-GTM F4B-GTAH-09 F4B-GTMAH-40M AN-GTM-09-40M 1-11/ F4B-GTMAH AN-GTM F4B-GTMAH F4B-GTAH AN-GTM F4B-GTMAH-45M to order B2-60

61 /DIMENSIONS GTMAH AIR HANDLING MEDIUM DUTY 4 BOLT FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs. A B C# D Bolt H J L N Z kg Dia / /64 3-3/4 1-35/64 2-3/4 7/16 1/2 21/ /64 2-1/ / /64 4-1/4 1-45/64 3-1/4 7/16 1/2 11/16 2-5/64 2-3/16 1-3/4 25mm M / /8 4-3/4 1-49/64 3-5/8 1/2 9/16 41/64 2-3/8 2-7/ / / mm M / /32 5-1/8 1-31/32 4 1/2 9/16 43/64 2-5/8 2-3/8 2-7/32 35mm M / /64 5-3/ /8 1/2 5/8 11/ /64 2-3/4 2-3/32 40mm M / /64 5-5/8 2-3/64 4-3/8 1/2 5/8 21/32 3-1/8 2-7/8 2-1/ / mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-61

62 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTMAH AIR HANDLING MEDIUM DUTY 4 BOLT FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-15/ F4B-GTMAH AN-GTM F4B-GTMAH F4B-GTAH AN-GTM F4B-GTMAH-50M AN-GTM-11-50M 2-3/ F4B-GTMAH AN-GTM F4B-GTMAH F4B-GTAH AN-GTM F4B-GTMAH-55M AN-GTM-12-55M 2-7/ F4B-GTMAH AN-GTM F4B-GTMAH F4B-GTAH AN-GTM F4B-GTMAH-65M AN-GTM-14-65M 215 F4B-GTMAH AN-GTM F4B-GTAH-15 F4B-GTMAH-70M AN-GTM-11-70M 2-15/ F4B-GTMAH AN-GTM F4B-GTMAH F4B-GTAH AN-GTM F4B-GTMAH-75M AN-GTM-16-75M 3-7/ F4B-GTMAH AN-GTM F4B-GTMAH F4B-GTAH AN-GTM F4B-GTMAH-85M to order B2-62

63 /DIMENSIONS Bearing Quick Reference E-Z KLEEN Weight F lbs. A B C# D Bolt H J L N Z kg Dia. 1-15/ /64 6-1/2 2-9/64 5-1/8 5/8 11/16 11/16 3-1/4 3-1/4 2-9/ mm M / /64 6-7/8 2-5/16 5-5/8 5/8 11/16 23/32 3-1/2 3-1/2 2-7/ / mm M / /64 7-3/8 2-53/64 5-7/8 5/8 11/16 23/ / / / / mm M / /64 7-3/4 3-3/16 6 3/4 1 51/64 4-1/4 3-7/8 3-3/64 70mm M / /16 7-3/4 3-3/8 6 3/4 7/8 57/64 4-1/2 4-9/ / mm M / /64 8-7/ /64 6-3/4 3/4 1 53/ /8 3-39/64 85mm M #C dimension will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-63

64 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY PILOTED FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-1/ FC-GT AN-GT / FC-GT AN-GT FC-GT / FC-GT-104S AN-GT S 30mm FC-GT-30M AN-GT-06-30M 1-1/ FC-GT AN-GT / FC-GT AN-GT FC-GT / FC-GT AN-GT mm FC-GT-35M AN-GT-07-35M 1-1/ FC-GT AN-GT / FC-GT FC-GT AN-GT mm FC-GT-40M AN-GT-08-40M 1-5/ FC-GT-110L AN-GT L 1-11/ FC-GT AN-GT FC-GT / FC-GT AN-GT mm FC-GT-45M AN-GT-09-45M 1-15/ FC-GT AN-GT FC-GT FC-GT AN-GT mm FC-GT-50M AN-GT-10-50M FC-GTM AN-GTM / FC-GT AN-GT FC-GT / FC-GT AN-GT mm FC-GT-55M AN-GT-11-55M 2-1/ FC-GTM AN-GTM / FC-GT FC-GT AN-GT mm FC-GT-60M AN-GT-12-60M 2-1/ FC-GTM AN-GTM / FC-GT FC-GT AN-GT mm FC-GT-70M AN-GT-14-70M B2-64

65 /DIMENSIONS GT NORMAL DUTY PILOTED FLANGE BEARINGS Bearing Quick Reference E-Z KLEEN Weight F lbs A B C# D E Bolt G# H K* L Z kg Dia. 1-1/ /64 4-3/8 1-43/64 3-5/8 1/4 3/8 1-27/64 13/ / /32 1-3/ / mm M / / /64 4-1/8 3/8 3/8 1-27/64 27/32 3-3/8 2-3/8 1-1/ / / mm M / /32 5-1/4 1-31/32 4-3/8 7/16 7/ /32 57/64 3-5/8 2-5/8 1-37/ / mm M / /64 5-3/4 1-61/64 4-3/4 7/16 1/2 1-33/64 29/ / / / / mm M / /64 6-1/ /8 15/32 1/2 1-17/32 59/64 4-1/4 3-1/8 1-19/ mm M /64 6-3/8 2-7/32 5-3/8 5/8 1/2 1-19/ /2 3-27/ / / / mm M / /64 7-1/8 2-15/32 6 7/8 1/2 1-19/ / / / mm M / /64 7-5/8 2-53/64 6-1/2 1-1/8 1/2 1-45/64 1-1/16 5-1/ / / mm M #C & G dimensions will vary slightly depending on true shaft diameter. * * mm GRIP TIGHT Adapter Ball Bearing B2-65

66 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY PILOTED FLANGE BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description FC-GTM AN-GTM FC-GT-06 25mm FC-GTM-25M AN-GTM-06-25M 1-3/ FC-GTM AN-GTM / FC-GT FC-GT AN-GT mm FC-GTM-30M AN-GTM-07-30M 1-7/ FC-GTM AN-GTM / FC-GT FC-GT AN-GT mm FC-GTM-35M AN-GTM-08-35M 1-1/ FC-GTM-108L AN-GTM / FC-GT-110L FC-GT AN-GT mm FC-GTM-40M AN-GTM-09-40M 1-11/ FC-GTM AN-GTM / FC-GTM FC-GT AN-GTM mm FC-GTM-45M AN-GTM-10-45M 1-15/ FC-GTM AN-GTM FC-GTM FC-GT AN-GTM mm FC-GTM-50M AN-GTM-11-50M 2-3/ FC-GTM AN-GTM / FC-GTM FC-GT AN-GTM mm FC-GTM-55M AN-GTM-12-55M 2-7/ FC-GTM AN-GTM / FC-GTM FC-GT AN-GTM mm FC-GTM-65M AN-GTM-14-65M 2-15/ FC-GTM AN-GTM FC-GTM FC-GT AN-GTM mm FC-GTM-75M AN-GTM-16-75M 3-7/ FC-GTM AN-GTM / FC-GTM FC-GT AN-GTM mm FC-GTM-85M to order B2-66

67 /DIMENSIONS GTM MEDIUM DUTY PILOTED FLANGE BEARINGS E-Z KLEEN Bearing Quick Reference Weight F lbs A B C# D E Bolt G# H K* L Z kg Dia /64 4-3/8 1-43/64 3-5/8 1/4 3/8 1-27/64 13/ / /32 25mm M / / /64 4-1/8 3/8 3/8 1-27/64 27/32 3-3/8 2-3/8 1-1/ / mm M / /32 5-1/4 1-31/32 4-3/8 7/16 7/ /32 57/64 3-5/8 2-5/8 1-37/ / mm M / /64 5-3/4 1-61/64 4-3/4 7/16 1/2 1-33/64 29/ / / / mm M / /64 6-1/ /8 15/32 1/2 1-17/32 59/64 4-1/4 3-1/8 1-19/ / mm M / /64 6-3/8 2-7/32 5-3/8 5/8 1/2 1-19/ /2 3-27/ / mm M / /64 7-1/8 2-15/32 6 7/8 1/2 1-19/ / / / mm M / /64 7-5/8 2-53/64 6-1/2 1-1/8 1/2 1-45/64 1-1/16 5-1/ / / mm M / /16 8-3/4 3-5/16 7-1/2 1-1/4 5/8 2-9/64 1-3/16 6-3/8 4-11/16 2-1/ mm M / / /4 3-17/32 8-5/8 1-1/8 3/4 2-13/32 1-5/8 7-3/8 5-3/16 2-7/ mm M #C & G dimensions will vary slightly depending on true shaft diameter. * * mm GRIP TIGHT Adapter Ball Bearing B2-67

68 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY NARROW SLOT TAKE-UP BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 204 3/ NSTU-GT AN-GT NSTU-GT-04 20mm NSTU-GT-20M AN-GT-04-20M 7/ NSTU-GT AN-GT / NSTU-GT AN-GT NSTU-GT NSTU-GT AN-GT mm NSTU-GT-25M AN-GT-05-25M 1-1/ NSTU-GT AN-GT / NSTU-GT AN-GT NSTU-GT / NSTU-GT-104S AN-GT S 30mm NSTU-GT-30M AN-GT-06-30M 1-1/ NSTU-GT AN-GT / NSTU-GT AN-GT NSTU-GT / NSTU-GT AN-GT mm NSTU-GT-35M AN-GT-07-35M 1-1/ NSTU-GT AN-GT / NSTU-GT NSTU-GT AN-GT mm NSTU-GT-40M Assembled to order B2-68

69 /DIMENSIONS GT NORMAL DUTY NARROW SLOT TAKE-UP BEARINGS E-Z KLEEN Bearing Quick Reference Take- Weight F P Up lbs A B C* D E Screw G H J L M@ N Pin R# S# Z Frame kg Dia. Dia. 3/ /32 3-1/2 1/4 1-1/2 2-3/16 3/4 7/16 7/8 1-3/8 1-1/2 2-5/8 3-1/8 5/16 31/64 63/64 1-3/ mm / / NS /64 3-9/16 1/4 1-1/2 2-3/16 3/4 7/16 7/8 1-3/8 1-51/64 2-5/8 3-1/8 5/16 1/2 61/64 1-1/64 25mm / / /4 2.6 NS /64 4-5/16 1/4 2-1/2 2-11/16 3/4 1/2 15/16 1-3/8 2-5/64 3-1/2 4-1/8 5/16 17/32 1-5/64 1-1/8 30mm / / / NS /8 4-1/2 1/4 2-1/2 2-11/16 3/4 1/2 15/16 1-3/8 2-3/8 3-1/2 4-1/8 5/16 9/16 1-1/16 1-9/64 35mm / /32 5-3/8 5/ /4 7/8 21/32 1-5/32 2-5/8 2-5/ /4 3/8 21/32 1-3/ / /8 4.5 NS400 40mm #R & S dimensions will vary slightly depending on true shaft diameter. * +/-.015, +.010, mm, -.50mm GRIP TIGHT Adapter Ball Bearing B2-69

70 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY NARROW SLOT TAKE-UP BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-5/ NSTU-GT-110L AN-GT L / NSTU-GT AN-GT NSTU-GT / NSTU-GT AN-GT mm NSTU-GT-45M AN-GT-09-45M 1-15/ NSTU-GT AN-GT NSTU-GT NSTU-GT AN-GT mm NSTU-GT-50M AN-GT-10-50M NSTU-GTM AN-GTM / NSTU-GT AN-GT NSTU-GT / NSTU-GT AN-GT mm NSTU-GT-55M AN-GT-11-55M 2-1/ NSTU-GTM AN-GTM / NSTU-GT NSTU-GT AN-GT mm NSTU-GT-60M Assembled to order B2-70

71 /DIMENSIONS GT NORMAL DUTY NARROW SLOT TAKE-UP BEARINGS Bearing Quick Reference E-Z KLEEN Weight Take-Up F P lbs Frame A B C* D E Screw G H J L M@ N Pin R# S# Z kg Dia. Dia / / /4 4.7 NS /64 5-7/16 5/ /4 7/8 23/32 1-7/32 1-5/8 2-55/ /4 3/8 21/32 1-3/16 1-9/32 45mm / /64 5-1/2 5/ /4 7/8 19/32 1-3/32 1-5/8 3-1/ /4 3/8 21/ /64 1-9/ NS mm / /4 6.5 NS /64 6-1/8 5/16 3-1/2 3-5/8 1 11/16 1-9/32 1-3/4 3-27/64 4-7/16 5-3/8 7/16 45/64 1-7/ /32 55mm / / /16 5/16 3-3/4 3-7/8 1 11/16 1-9/32 1-5/8 3-11/ /16 5-3/4 7/16 49/ / / / NS415 60mm #R & S dimensions will vary slightly depending on true shaft diameter. * +/-.015, +.010, mm, -.50mm GRIP TIGHT Adapter Ball Bearing B2-71

72 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY NARROW SLOT TAKE-UP BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 205 3/ NSTU-GTM NSTU-GT AN-GTM NSTU-GTM AN-GTM NSTU-GTU-06 25mm NSTU-GTM-25M AN-GTM-06-25M 1-3/ NSTU-GTM AN-GTM / NSTU-GT NSTU-GT AN-GT mm NSTU-GTM-30M AN-GTM-07-30M / NSTU-GTM AN-GTM NSTU-GT-08 35mm NSTU-GTM-35M AN-GTM-08-35M / NSTU-GTM AN-GTM NSTU-GT-09 40mm NSTU-GTM-40M AN-GTM-09-40M 1-11/ NSTU-GTM AN-GTM / NSTU-GTM NSTU-GT AN-GTM mm NSTU-GTM-45M AN-GTM-10-45M 1-15/ NSTU-GTM AN-GTM NSTU-GTM NSTU-GT AN-GTM mm NSTU-GTM-50M AN-GTM-11-50M 2-3/ NSTU-GTM AN-GTM / NSTU-GTM NSTU-GT AN-GTM mm NSTU-GTM-55M Assembled to order B2-72

73 /DIMENSIONS GTM MEDIUM DUTY NARROW SLOT TAKE-UP BEARINGS Bearing Quick Reference E-Z KLEEN Weight lbs kg Take- Up Frame A B C* D E F Screw Dia. G H J L M@ N P Pin Dia. R# S# Z 1-15/32 3-1/2 1/4 1-1/2 2-3/16 3/4 7/16 7/8 1-3/8 1-1/2 2-5/8 3-1/8 5/16 31/64 63/64 63/ /4 1.7 NS /64 4-5/16 1/4 2-1/2 2-11/16 3/4 1/2 15/16 1-3/ /2 4-1/8 5/16 17/32 1-5/64 1-1/32 NS308 25mm / /8 4-1/2 1/4 2-1/2 2-11/16 3/4 1/2 15/16 1-3/8 2-19/64 3-1/2 4-1/8 5/16 9/16 1-1/16 1-3/ /4 NS mm / /32 5-3/8 5/ /4 7/8 21/32 1-5/32 1-5/8 2-1/ /4 3/8 21/32 1-3/16 1-9/64 NS400 35mm / /32 5-7/16 5/ /4 7/8 23/32 1-7/32 1-5/8 2-43/ /4 3/8 21/32 1-3/16 1-5/32 NS400 40mm / /64 5-1/2 5/ /4 7/8 19/32 1-3/32 1-5/8 2-15/ /4 3/8 21/ /64 1-5/ /4 NS400 45mm / /64 6-1/8 5/16 3-1/2 3-5/8 1 11/16 1-9/32 1-3/4 3-1/4 4-7/16 5-3/8 7/16 45/64 1-7/32 1-3/ NS407 50mm / / /16 5/16 3-3/4 3-7/8 1 11/16 1-9/32 1-5/8 3-1/2 4-15/16 5-3/4 7/16 49/ /32 1-5/ /4 NS415 55mm #R & S dimensions will vary slightly depending on true shaft diameter. * +/-.015, +.010, mm, -.50mm GRIP TIGHT Adapter Ball Bearing B2-73

74 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY WIDE SLOT TAKE-UP BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 204 3/ WSTU-GT AN-GT WSTU-GT-04 20mm WSTU-GT-20M AN-GT-04-20M 7/ WSTU-GT AN-GT / WSTU-GT AN-GT WSTU-GT WSTU-GT AN-GT mm WSTU-GT-25M AN-GT-05-25M 1-1/ WSTU-GT AN-GT / WSTU-GT AN-GT WSTU-GT / WSTU-GT-104S AN-GT S 30mm WSTU-GT-30M AN-GT-06-30M 1-1/ WSTU-GT AN-GT / WSTU-GT AN-GT WSTU-GT / WSTU-GT AN-GT mm WSTU-GT-35M AN-GT-07-35M 1-1/ WSTU-GT AN-GT / WSTU-GT WSTU-GT AN-GT mm WSTU-GT-40M Assembled to order B2-74

75 /DIMENSIONS GT NORMAL DUTY WIDE SLOT TAKE-UP BEARINGS E-Z KLEEN Bearing Quick Reference Weight lbs kg Take- Up Frame F A B C* D E Screw G H J K L M* N R# S# T Z Dia. 3/ / /16 17/ /8 5/8 3/8 5/ /4 1-1/ /8 31/64 63/64 1-3/8 1-3/64 20mm / / WS / /16 17/ /16 5/8 3/8 5/ / / /8 1/2 61/64 1-3/8 1-1/64 25mm / / /4 2.5 WS /64 4-3/8 17/32 2-1/4 2-3/4 3/4 3/8 5/8 2-3/16 1-7/16 2-5/64 3-1/2 4-1/8 17/32 1-5/64 1-5/8 1-1/8 30mm / / / WS /8 4-7/8 17/32 2-1/2 3-1/16 3/4 1/2 5/8 2-1/2 1-7/16 2-3/8 3-1/2 4-1/8 9/16 1-1/16 1-5/8 1-9/64 35mm / / /16 11/16 3-1/4 3-1/2 1 5/8 3/4 3-1/4 1-15/16 2-5/ /2 21/32 1-3/ / / /8 5.9 WS400 40mm #R & S dimensions will vary slightly depending on true shaft diameter. *+/-.015, +/-.38mm GRIP TIGHT Adapter Ball Bearing B2-75

76 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY WIDE SLOT TAKE-UP BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-5/ WSTU-GT-110L AN-GT / WSTU-GT AN-GT WSTU-GT / WSTU-GT AN-GT mm WSTU-GT-45M AN-GT-09-45M 1-15/ WSTU-GT AN-GT WSTU-GT WSTU-GT AN-GT mm WSTU-GT-50M AN-GT-10-50M WSTU-GTM AN-GTM / WSTU-GT AN-GT WSTU-GT / WSTU-GT AN-GT mm WSTU-GT-55M AN-GT-11-55M 2-1/ WSTU-GTM AN-GTM / WSTU-GT WSTU-GT AN-GT mm WSTU-GT-60M AN-GT-12-60M 2-1/ WSTU-GTM AN-GTM / WSTU-GT WSTU-GT AN-GT mm WSTU-GT-70M AN-GT-14-70M 2-15/ WSTU-GT AN-GT WSTU-GT WSTU-GT AN-GT mm WSTU-GT-75M Assembled to order B2-76

77 /DIMENSIONS GT NORMAL DUTY WIDE SLOT TAKE-UP BEARINGS E-Z KLEEN Bearing Quick Reference Wgt. Take- Up F lbs Frame A B C* D E Screw G H J K L M* N R# S# T Z / / /4 5.9 kg Dia. WS /64 5-5/8 11/16 3-1/4 3-7/16 1 5/8 3/4 3-1/4 1-15/ / /4 21/32 1-3/ /16 1-9/32 45mm / /645-13/16 11/16 3-3/8 3-9/16 1 5/8 3/4 3-1/4 1-15/16 3-1/ /4 21/ /641-15/16 1-9/ WS mm / WS / /646-11/16 1-1/16 3-3/4 4-3/16 1-1/4 3/ /2 3-27/64 5-1/8 5-7/8 45/64 1-7/32 2-1/2 1-11/32 55mm / /64 7-1/2 1-1/ /16 1-1/4 3/4 1-1/ /2 3-11/16 5-1/8 5-7/8 49/ /32 2-1/2 1-15/ / WS502 60mm / /64 8-9/16 1-1/16 4-3/4 5-3/8 1-1/2 13/16 1-1/4 4-3/8 2-3/ /16 6-9/16 7/8 1-33/64 2-3/4 1-19/ / WS515 70mm / /64 9-1/8 1-1/16 4-3/4 5-1/2 1-1/2 13/16 1-1/4 4-3/8 2-3/4 4-7/ / /16 57/ /64 2-3/4 1-5/ WS515 75mm #R & S dimensions will vary slightly depending on true shaft diameter. *+/-.015, +/-.38mm GRIP TIGHT Adapter Ball Bearing B2-77

78 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY WIDE SLOT TAKE-UP BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 205 3/ WSTU-GTM WSTU-GT AN-GTM WSTU-GTM AN-GTM WSTU-GTU-06 25mm WSTU-GTM-25M AN-GTM-06-25M 1-3/ WSTU-GTM AN-GTM / WSTU-GT WSTU-GT AN-GT mm WSTU-GTM-30M AN-GTM-07-30M / WSTU-GTM AN-GTM WSTU-GT-08 35mm WSTU-GTM-35M AN-GTM-08-35M / WSTU-GTM AN-GTM WSTU-GT-09 40mm WSTU-GTM-40M AN-GTM-09-40M 1-11/ WSTU-GTM AN-GTM / WSTU-GTM WSTU-GT AN-GTM mm WSTU-GTM-45M Assembled to order B2-78

79 /DIMENSIONS GTM MEDIUM DUTY WIDE SLOT TAKE-UP BEARINGS Bearing Quick Reference E-Z KLEEN Weight Take-Up F lbs Frame A B C* D E Screw G H J K L M* N R# S# T Z kg Dia. 1-29/ /16 17/ /16 5/8 3/8 5/ / / /8 1/2 61/64 1-3/8 61/ /4 2.7 WS /64 4-3/8 17/32 2-1/4 2-3/4 3/4 3/8 5/8 2-3/16 1-7/16 2-5/64 3-1/2 4-1/8 17/32 1-5/64 1-5/8 1-1/8 WS308 25mm / /8 4-7/8 17/32 2-1/2 3-1/16 3/4 1/2 5/8 2-1/2 1-7/16 2-3/8 3-1/2 4-1/8 9/16 1-1/16 1-5/8 1-9/ /4 WS308 30mm / / /16 11/16 3-1/4 3-1/2 1 5/8 3/4 3-1/4 1-15/16 2-5/ /2 21/32 1-3/ / /64 WS400 35mm / /64 5-5/8 11/16 3-1/4 3-7/16 1 5/8 3/4 3-1/4 1-15/ / /4 21/32 1-3/ /16 1-9/32 WS400 40mm / / /16 11/16 3-3/8 3-9/16 1 5/8 3/4 3-1/4 1-15/16 3-1/ /4 21/ / /16 1-9/ /4 WS400 45mm #R & S dimensions will vary slightly depending on true shaft diameter. *+/-.015, +/-.38mm GRIP TIGHT Adapter Ball Bearing B2-79

80 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY WIDE SLOT TAKE-UP BEARINGS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-15/ WSTU-GTM AN-GTM WSTU-GTM WSTU-GT AN-GTM mm WSTU-GTM-50M AN-GTM-11-50M 2-3/ WSTU-GTM AN-GTM / WSTU-GTM WSTU-GT AN-GTM mm WSTU-GTM-55M AN-GTM-12-55M 2-7/ WSTU-GTM AN-GTM / WSTU-GTM WSTU-GT AN-GTM mm WSTU-GTM-65M AN-GTM-14-65M / WSTU-GTM WSTU-GT AN-GTM mm WSTU-GTM-70M AN-GTM-15-70M 2-15/ WSTU-GTM AN-GTM WSTU-GTM WSTU-GT AN-GTM mm WSTU-GTM-75M Assembled to order B2-80

81 /DIMENSIONS GTM MEDIUM DUTY WIDE SLOT TAKE-UP BEARINGS E-Z KLEEN Bearing Quick Reference Weight lbs kg Take- Up F Frame A B C* D E Screw G H J K L M* N R# S# T Z Dia. 1-15/ / /16 1-1/16 3-3/4 4-3/16 1-1/4 3/ /2 3-27/64 5-1/8 5-7/8 45/64 1-7/32 2-1/2 1-11/ WS502 50mm / /64 7-1/2 1-1/ /16 1-1/4 3/4 1-1/ /2 3-11/16 5-1/8 5-7/8 49/ /32 2-1/2 1-15/ /4 WS502 55mm / /64 8-9/16 1-1/16 4-3/4 5-3/8 1-1/2 13/16 1-1/4 4-3/8 2-3/ /16 6-9/16 7/8 1-33/64 2-3/4 1-19/ / WS515 65mm / /64 9-1/8 1-1/16 4-3/4 5-1/2 1-1/2 13/16 1-1/4 4-3/8 2-3/4 4-7/ / /16 57/ /64 2-3/4 1-5/8 WS515 70mm / /16 9-1/8 1-1/16 4-3/4 5-1/2 1-1/2 13/16 1-1/4 4-3/8 2-3/4 4-11/16 6-1/2 7-1/4 29/ /64 2-3/4 1-5/ WS608 75mm #R & S dimensions will vary slightly depending on true shaft diameter. *+/-.015, +/-.38mm GRIP TIGHT Adapter Ball Bearing B2-81

82 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY TOP ANGLE TAKE-UP BEARINGS Complete Unit Unit Without Adapter & Nut Adapter & Nut Assembly Part No. Description Part No. Description Part No. Description 1-15/ TP-GT AN-GT TP-GT TP-GT AN-GT TP-GTM AN-GTM / TP-GT TP-GT AN-GT / TP-GT AN-GT / TP-GTM TP-GT AN-GTM / TP-GT AN-GT / TP-GTM TP-GT AN-GTM / TP-GT AN-GT / TP-GT TP-GT Assembled to order B2-82

83 /DIMENSIONS GT NORMAL DUTY TOP ANGLE TAKE-UP BEARINGS Bearing Quick Reference E-Z KLEEN Take-Up Weight Frame A B C D E J L R# S# T Z lbs 1-15/ TP /64 6-1/2 2-3/ /4 6-3/8 3-1/8 21/ /64 2-3/8 1-9/ /16 TP / /2 6-3/4 3-3/8 6-7/8 3-27/64 45/64 1-7/32 2-3/8 1-11/32 2-1/ TP30 2-7/64 7-1/2 2-3/ /2 7-7/ /16 49/ /32 2-3/4 1-15/ TP /64 8-1/2 2-1/ /16 4 7/8 1-33/64 2-3/4 1-19/32 2-1/4 2-1/ / / / TP /64 8-1/2 2-1/ /16 4-7/16 57/ /64 2-3/4 1-5/8 Lube fi tting thread size - 1/8-27 NPT #R & S dimensions will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-83

84 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY TOP ANGLE TAKE-UP BEARINGS Complete Unit Unit Without Adapter & Nut Adapter & Nut Assembly Part No. Description Part No. Description Part No. Description 1-11/ TP-GTM AN-GTM TP-GT / TP-GTM AN-GTM / TP-GTM AN-GTM TP-GT TP-GTM AN-GTM / TP-GTM AN-GTM TP-GT / TP-GTM AN-GTM / TP-GTM AN-GTM TP-GT / TP-GTM AN-GTM / TP-GM TP-GT AN-GTM / TP-GTM AN-GTM TP-GT TP-GTM AN-GTM / TP-GTM AN-GTM TP-GT / TP-GTM AN-GTM B2-84

85 /DIMENSIONS GTM MEDIUM DUTY TOP ANGLE TAKE-UP BEARINGS Bearing Quick Reference E-Z KLEEN Take-Up Weight Frame A B C D E J L R# S# T Z lbs 1-11/ TP /64 6-1/2 2-3/ /4 6-3/8 3-1/8 21/ /64 2-3/8 1-9/32 1-3/ / TP / /2 6-3/4 3-3/8 6-7/8 3-27/64 45/64 1-7/32 2-3/8 1-11/ TP30 2-7/64 7-1/2 2-3/ /2 7-7/ /16 49/ /32 2-3/4 1-15/ TP /64 8-1/2 2-1/ /16 4 7/8 1-33/64 2-3/4 1-19/32 2-3/16 2-7/ /4 2-1/ GRIP TIGHT Adapter Ball Bearing / TP /64 8-1/2 2-1/ /16 4-7/16 57/ /64 2-3/4 1-5/8 2-15/ TP /16 9-1/2 2-3/ /2 9-5/8 4-11/16 29/ /64 3-1/8 1-5/ TP / /8 10-1/2 5-1/ / /64 3-1/8 1-45/64 Lube fi tting thread size - 1/8-27 NPT #R & S dimensions will vary slightly depending on true shaft diameter. 3-7/ / B2-85

86 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY BEARING INSERTS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1/ INS-GT AN-GT / INS-GT INS-GT AN-GT mm INS-GT-17M AN-GT-03-17M 204 3/ INS-GT AN-GT INS-GT-04 20mm INS-GT-20M AN-GT-04-20M 7/ INS-GT AN-GT / INS-GT AN-GT INS-GT INS-GT AN-GT mm INS-GT-25M AN-GT-05-25M 1-1/ INS-GT AN-GT / INS-GT AN-GT INS-GT / INS-GT-104S AN-GT S 30mm INS-GT-30M AN-GT-06-30M 1-1/ INS-GT AN-GT / INS-GT AN-GT INS-GT / INS-GT AN-GT mm INS-GT-35M Assembled to order. B2-86

87 /DIMENSIONS GT NORMAL DUTY BEARING INSERTS Bearing Quick Reference E-Z KLEEN Weight N lbs A C D J L SetScrew W# X Y# kg (UNF) 1/ / /32 13/32 59/64 15/ /8 0.3 #10-32 x 1/4 17mm / / /2 31/64 63/64 63/ #10-32 x 1/4 20mm / / /64 1/2 61/64 61/64 15/ #10-32 x 1/ mm / / /32 1-1/32 1-5/64 #10-32 x 1/4 30mm / / /64 9/16 1-3/64 1-1/ #10-32 x 1/4 35mm #W & Y dimensions will vary slightly depending on true shaft diameter. 1-3/16 1-3/ /4 1-7/ GRIP TIGHT Adapter Ball Bearing B2-87

88 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT NORMAL DUTY BEARING INSERTS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-1/ INS-GT AN-GT / INS-GT INS-GT AN-GT mm INS-GT-40M AN-GT-08-40M 1-5/ INS-GT-110L AN-GT L / INS-GT AN-GT INS-GT / INS-GT AN-GT mm INS-GT-45M AN-GT-09-45M 1-15/ INS-GT AN-GT INS-GT INS-GT AN-GT mm INS-GT-50M AN-GT-10-50M INS-GTM AN-GTM / INS-GT AN-GT INS-GT / INS-GT AN-GT mm INS-GT-55M AN-GT-11-55M 2-1/ INS-GTM AN-GTM / INS-GT INS-GT AN-GT mm INS-GT-60M AN-GT-12-60M 2-1/ INS-GTM AN-GTM / INS-GT INS-GT AN-GT mm INS-GT-70M AN-GT-14-70M 2-15/ INS-GT AN-GT INS-GT INS-GT AN-GT mm INS-GT-75M Assembled to order. B2-88

89 /DIMENSIONS GT NORMAL DUTY BEARING INSERTS Bearing Quick Reference E-Z KLEEN Weight N lbs A C D J L SetScrew W# X Y# kg (UNF) 1-1/ / /2 21/32 1-9/64 1-3/ /8 2.0 #10-32 x 1/4 40mm / / /64 21/32 1-5/32 1-3/ / /4 2.5 #10-32 x 1/4 45mm / / /16 21/32 1-5/ / #10-32 x 1/4 50mm / /4 45/64 1-3/16 1-7/ / /4 3.3 #10-32 x 1/4 55mm / / /2 49/64 1-5/ / / #10-32 x 1/4 60mm / / /16 7/8 1-15/ / / #10-32 x 1/4 70mm / / /4 57/64 1-5/8 1-43/ #10-32 x 1/4 75mm #W & Y dimensions will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-89

90 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY BEARING INSERTS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 205 3/ INS-GTM INS-GT AN-GTM INS-GTM AN-GTM INS-GT-06 25mm INS-GTM-25M AN-GTM-06-25M 1-3/ INS-GTM AN-GTM / INS-GT INS-GT AN-GT mm INS-GTM-30M AN-GTM-07-30M / INS-GTM AN-GTM INS-GT-08 35mm INS-GTM-35M AN-GTM-08-35M 1-1/ INS-GTM AN-GTM / INS-GT-110L INS-GT-09 40mm INS-GTM-40M AN-GTM-09-40M 1-11/ INS-GTM AN-GTM / INS-GTM INS-GT AN-GTM mm INS-GTM-45M Assembled to order. B2-90

91 /DIMENSIONS GTM MEDIUM DUTY BEARING INSERTS Bearing Quick Reference E-Z KLEEN Weight N lbs A C D J L SetScrew W# X Y# kg (UNF) 205 3/ / /64 #10-32 x 1/4 1/2 61/64 61/ / /32 1-1/32 1-5/64 #10-32 x 1/4 25mm / / /64 9/16 1-3/64 1-1/ /4 1.7 #10-32 x 1/4 30mm / / /2 21/32 1-9/64 1-3/16 #10-32 x 1/4 35mm / / /64 21/32 1-5/32 1-3/ /8 2.5 #10-32 x 1/4 40mm / / /16 21/32 1-5/ / /4 3.0 #10-32 x 1/4 45mm #W & Y dimensions will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-91

92 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GTM MEDIUM DUTY BEARING INSERTS Complete Unit Unit without Adapter Sleeve & Lock Nut Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description Part No. Description 1-15/ INS-GTM AN-GTM INS-GTM INS-GT AN-GTM mm INS-GTM-50M AN-GTM-11-50M 2-3/ INS-GTM AN-GTM / INS-GTM INS-GT AN-GTM mm INS-GTM-55M AN-GTM-12-55M 2-7/ INS-GTM AN-GTM / INS-GTM INS-GT AN-GTM mm INS-GTM-65M AN-GTM-14-65M / INS-GTM AN-GTM INS-GT-15 70mm INS-GTM-70M AN-GTM-15-70M 2-15/ INS-GTM AN-GTM INS-GTM INS-GT AN-GTM mm INS-GTM-75M AN-GTM-16-75M 3-7/ INS-GTM AN-GTM / INS-GTM INS-GT AN-GTM mm INS-GTM-85M Assembled to order. B2-92

93 /DIMENSIONS GTM MEDIUM DUTY BEARING INSERTS Bearing Quick Reference E-Z KLEEN Weight N lbs A C D J L SetScrew W# X Y# kg (UNF) 1-15/ / /4 45/64 1-3/16 1-7/ #10-32 x 1/4 50mm / / /2 49/64 1-5/ / /4 4.8 #10-32 x 1/4 55mm / / /16 7/8 1-15/ / /2 5.4 #10-32 x 1/4 65mm / / /4 57/64 1-5/8 1-43/64 #10-32 x 1/4 70mm / / /2 29/ / / #10-32 x 1/4 75mm / / /4 1-51/ /2 8.7 #10-32 x 1/4 85mm #W & Y dimensions will vary slightly depending on true shaft diameter. GRIP TIGHT Adapter Ball Bearing B2-93

94 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing /DIMENSIONS GT AND GTM ADAPTER & LOCK NUT ASSEMBLIES Adapter Sleeve & Lock Nut Assembly Adapter Sleeve & Lock Nut Assembly Part No. Description Part No. Description 1/ AN-GT / AN-GTM / AN-GT / AN-GTM mm AN-GT-03-17M 1-15/ AN-GT / AN-GT AN-GT mm AN-GT-04-20M 45mm AN-GTM-10-45M 3/ AN-GTM mm AN-GT-10-50M 7/ AN-GT / AN-GTM / AN-GT AN-GTM AN-GT / AN-GT mm AN-GT-05-25M 2-1/ AN-GT AN-GTM mm AN-GTM-11-50M 1-1/ AN-GT mm AN-GT-11-55M 1-3/ AN-GT / AN-GTM / AN-GT S 2-1/ AN-GTM mm AN-GTM-06-25M / AN-GT mm AN-GT-06-30M 55mm AN-GTM-12-55M 1-3/ AN-GTM mm AN-GT-12-60M 1-1/ AN-GT / AN-GTM / AN-GT / AN-GTM / AN-GT / AN-GT mm AN-GTM-07-30M 65mm AN-GTM-14-65M 35mm AN-GT-07-35M 70mm AN-GT-14-70M 1-7/ AN-GTM / AN-GTM / AN-GT / AN-GT / AN-GT AN-GT mm AN-GTM-08-35M 70mm AN-GTM-15-70M 40mm AN-GT-08-40M 75mm AN-GT-15-75M 1-1/ AN-GTM / AN-GTM / AN-GT L AN-GTM / AN-GT mm AN-GTM-16-75M 1-3/ AN-GT / AN-GTM mm AN-GTM-09-40M / AN-GTM mm AN-GT-09-45M 85mm AN-GTM-18-85M B2-94

95 /DIMENSIONS GT AND GTM ADAPTER & LOCK NUT ASSEMBLIES E-Z KLEEN Bearing Quick Reference Weight Weight lbs A B L lbs kg kg A B L 1/ / / / / / mm / / / mm mm / / mm.3 7/ / / / / mm / / mm /8.4 55mm.4 1-3/ / / / / mm / mm.2 55mm / / mm.6 1-1/ / / / / / / mm mm mm.2 70mm.6 1-7/ / /11/ / / / / mm mm mm.3 75mm / / / / / / mm / / / mm / mm.3 85mm GRIP TIGHT Adapter Ball Bearing B2-95

96 Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing DODGE Ball Bearing End Covers Fits DODGE cast iron housed ball bearings: Pillow Blocks, 2 and 4 Bolt fl anges, and Take-Up bearings Injected molded, impact resistant, OSHA safety yellow end covers meet requirements for exposed rotating shafts Stainless steel C washer for gripping power No modifi cation or machining of existing housings required Concentric knockout grooves on inside of end cover for thrushaft DODGE six digit part number and description embossed inside Operating temperature to 250 F For no relubrication/sealed for life applications (-NL), part number hex head plug is available /DIMENSIONS PAGE B2-8 B2-96