Bearing Reference CONTENTS. Guide S-2000

Transcription

1 ONTENTS Features / Benefits... B12-2 Specifications B12-4 How to Order... B12-4 Nomenclature B12-5 Selection... B12-7 Dimensions Pillow Block... B12-14 Flanges B12-30 Piloted Flange B12-38 Wide-Slot Take-Ups... B12-42 TP Take-Up... B12-46 Bearing Inserts... B12-48 End ap... B12-50 Part Number Index INDE-1 Key Word Index... KEYWORD-1 Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-1

2 Bearing Reference Longer Bearing Life By Design... E-Family Roller Specialty Tapered High capacity double row spherical rollers offer up to 250% more L 10 life than competitive brands Larger rollers More contact area ase-carburized inner rings resist cracking Static or dynamic misalignment up to ± 1º Expansion capability up to 3/8 (9.5mm) orrosion resistant flinger blocks contaminants Patented nitrile multiple lip seal resists heat and chemnical breakdown Seal land maintains full seal contact when misaligned UNISPHERE II IMPERIAL Reinforced polyamide cage Optional metallic labryrinth seal and steel cage provide high temperature and high speed capabilities Installation Savings... Factory lubed, sealed and adjusted, ready to slip onto the shaft 65º Springlok collar mount for increased holding power versus 90º or 120º Field convertible from non-expansion to expansion and expansion to non-expansion Elongated pillow block bolt holes to facilitate mounting 65 degree set screw mounting (dual collar on 4-7/16 and larger sizes) UNIFIED SAF B12-2

3 Offer Patented Seal Options To Maximize Bearing Life... TRIDENT Seals for low to medium speed Face rubbing triple lip seal Flinger to shield seal and bearing from contamination/damage Seal/land positive contact up to ± 1 degree of misalignment Patented design Labyrinth seals for higher speeds High speed for relatively clean environments Flinger shields seal and bearing from contamination/damage Seal operates with up to ± 1 degree of misalignment Patented design NOTE: Instruction manuals for Dodge bearings are available on Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-3

4 Bearing Reference E-Family Roller INH DODGE Spherical, including bearings, are general purpose, high-capacity, double-row spherical roller bearings. All are mounted in single piece precision machined housings. are mounted to shafts by means of set screw collars, with 65 degree set screw spacing for maximum clamping force. ASTM A48 lass 30 cast iron is the standard material used in housings. A-27 Grade lass 1 Steel is the standard material used in Steel S2000-HD housings. Housing designs are available for survival in extreme harsh environments, through the use of special finishes and stainless hardware. Housings are available in a variety of standard configurations, including pillow blocks, flanges, piloted flanges and take-up bearings. TRIDENT triple lip contact seal and Labyrinth seals are available on bearings. Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF HOW TO ORDER There are two ways to specify DODGE. Most of the product offerings have part numbers with listings shown throughout this catalog. Use of part numbers ensures accurate order processing. When part numbers are not shown, the product may be specified by description or part name. This method is used when ordering units that include modifications or options. To order by description, use the nomenclature key shown on page B12-5 and add any special instructions to the end of the description for options not covered by the nomenclature. DODGE Spherical are factory adjusted and pre-lubricated. For applications where extreme ambient temperatures, high speeds, or high loads are expected, a variety of specialty lubricants is available. Standard grease provided is lithium complex base Mobilgrease HP222. High temperature greases available include Mobil HTS #2. Other special lubricants are available upon request. Special lubricant options usually involve set-up charges, minimum quantities and list price premiums. To order, specify type of lubricant required at the end of the product name or after the standard part number. Example: except with Mobil HTS #2 grease or P2BS2108L except with Mobil HTS #2 grease For applications requiring modifications not listed, we encourage you to contact our Application Engineering Department for at SELETION PAGE B12-14 B12-4

5 NOMENLATURE S E P2B - S R E Bearing Reference E prefix denotes Type E dimensioned housing with S2000 spherical roller bearing insert * S prefix denotes cast steel housing P2B = P4B = F3R = F4S = F4R = F = HOUSING STYLE Pillow Block 2-Bolt Base, ast Iron Pillow Block 4-Bolt Base, ast Iron Flange Bearing 3-Bolt, ast Iron, Round Flange Bearing 4-Bolt, ast Iron, Square Flange Bearing 4-Bolt, ast Iron, Round Piloted Flanged (Flanged artridge) WSTU = Wide Slot Take-Up Bearing For Use In enter- Pull Frames TPHU = TPHU Take-up Bearing For Use In TPHU Or Top Angle Take-Up Frames BEARING TYPE SIZE SEAL OTHER DATA S2 = Inches and 16th R = TRIDENT Triple Lip Rubbing Seal 2 = 2 07 = 7/16 L = Labyrinth 207 = 2-7/16 Metallic Seal * Available in two or four bolt pillow blocks, four bolt square flanges and piloted flanges SELETION E = PAGE B12-14 Expansion Type Bearing - If E Does Not Appear, Bearing Is Non Expansion Type UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-5

6 Bearing Reference -E E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF Interchangeable with Type E style pillow blocks and flanges Same proven DODGE double row spherical insert 65 springlock collar mounting Up to ±1 misalignment capability Seal land on OD of inner ring maintains full contact pressure even when misaligned High capacity double row spherical bearing -HD Dodge S2000-HD mounted bearings feature proven S2000 technology deployed in steel housings designed specifically for harsh applications that demand superior housing strength. Major features include set screw mounting systems, high capacity cast steel housings with industry common dimensions, as well as high capacity, double row spherical inserts that are protected with either one of two effective sealing systems plus both closed & shaft-through end covers. 2-bolt pillow blocks in sizes 1-3/8 to 3-7/16 4-bolt pillow blocks in sizes 2-7/16 to 4-15/16 Flange bearings in sizes 1-3/8 to 4-7/16 Piloted flange bearings in sizes 1-3/8 to 4-15/16 In addition, S2000-HD feature single piece, sealed inserts that can be easily replaced in the field, without the time & trouble of a bearing tear down & rebuild. Field conversion between Non-Expansion & Expansion (fixed & float) can also be accomplished with the repositioning of a single snap ring. Housing configurations include two and four bolt base pillow blocks, and four bolt flanges. B12-6

7 SELETION SPHERIAL ROLLER BEARINGS DODGE Spherical Roller have the capacity to carry heavy radial loads and combined radial and thrust loads. The maximum recommended load which can be applied is limited by various components in the system such as bearing, housing, shaft, shaft attachment, speed and life requirements as listed in this catalog. DODGE spherical roller bearings have been applied successfully even when these limits have been exceeded under controlled operating conditions. ontact DODGE Application Engineering ( ) for applications which exceed the recommendations of this catalog. L 10 Hours Life - The life which may be expected from at least 90% of a given group of bearings operating under identical conditions. 10/ L 10 Life, Hours = ( ) P ( RPM ) Where: = Dynamic apacity (Table 1 on page B12-9) lbs. P = Equivalent Radial Load, lbs. GENERAL Heavy Service - For heavy shock loads, frequent shock loads, or severe vibrations, add up to 50% (according to severity of conditions) to the Equivalent Radial Load to obtain a Modified Equivalent Radial Load. onsult DODGE Application Engineering for additional selection assistance. Thrust load values shown in the table below are recommended as a guide for general applications that will give adequate L 10 life. Spherical bearings require a radial load at least equal to the thrust load for proper operation. If the thrust load exceeds this limit, consult Application Engineering. Where substantial radial load is also present, it is advisable to calculate actual L 10 life to assure that it meets the requirements. The effectiveness of the shaft attachment to carry thrust load depends on proper tightening of the set screws, shaft tolerance and shaft deflections. Therefore, it is advisable to use auxiliary thrust carrying devices such as shaft shoulder, snap ring or a thrust collar to locate the bearing under thrust loads heavier than shown below, or where extreme reliability is desired. RPM Over 2000 Recommended Thrust Load /20 /40 /60 The shaft tolerances recommended below are adequate for normal radial and radial/thrust load applications. The radial load is limited by the attachment to the shaft (see Table 1 on page B12-9). Where the applied radial load (F R) exceeds this limit (maximum allowable slip fit radial load), a snug-to-light press fit of the shaft is required. Since the allowable load, especially at a low speed, is very large, the shaft should be checked to assure adequate shaft strength. The magnitude and direction of both the thrust and radial load must be taken into account when selecting a housing. When pillow blocks are utilized, heavy loads should be directed through the base. Where uplift loads are involved, see Tables 6, 7 and 8 on pages B12-12 and B12-13 and for maximum values. Where a load pulls the housing away from the mounting base, both the hold-down bolts and housing must be of adequate strength. Auxiliary load carrying devices such as shear bars are advisable for side or end loading of pillow blocks and radial loads for flange units. Tolerances UP TO 1-1/ /16 TO /16 TO BEARING SUPPORTING RADIAL LOADS ONLY 1. Define L 10 Life Hours desired. 2. Establish bearing radial load, F R (F R = P for Pure Radial Load onditions). The DODGE program BEST can be used to find application loads. 3. Establish RPM. Using the easy selection Table 4 on page B12-10, find, under the RPM column, the equivalent radial load that equals or is slightly higher than the application radial load for the desired life. The shaft size on the far left will be the minimum shaft size that you can use for your application. If the desired life is different than the values shown on the chart, use alternate Method A shown below. Example: 1. L 10 Life = 30,000 Hours 2. Radial load = 4000 lbs. 3. RPM = 1,020 At the intersection of the 1,020 RPM column and the 30,000 hours L 10 life row, the equivalent radial load of 4092 lbs. exceeds the 4000 lbs. radial load for shaft size 2-7/16. A bearing with bore 2-7/16, or larger, may be used for this application. The DODGE Bearing Evaluation and Selection Technique (BEST) is a menu driven computer program that calculates bearing loads, fatigue life and operating temperature for a two bearing shaft system based on user supplied input parame ters. This interactive program is available at under the Product Selection area. PAGE B12-5 PAGE B12-14 Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-7

8 Bearing Reference E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL SELETION ALTERNATE METHOD A - SELETING A BEARING FOR AN L 10 LIFE VALUE NOT SHOWN IN THE EASY SELETION HART. The L 10 life equation can be rearranged so that the bearing dynamic capacity is identified in terms of L 10, RPM and P = ( ) 0.3 L 10 RPM P (P = F R for Pure Radial Load onditions) Since the L 10, RPM and P are known, solve for. Select from the dynamic capacity column on Table 1 on page B12-9 the value equal to or greater than the value just cal culated. The bore size on the far left represents the proper bore size selection. heck that the application RPM does not exceed the MA. RPM on Table 1. Also check that the radial load does not exceed the Maximum Allowable Slip Fit Radial Load shown on Table 1 on page B12-9. If it does, a line-to-line to light press fit of shaft is required. When selecting an L 10 life of less than 30,000 hours, par ticular attention must be paid to shaft deflection and proper lubricant selection. SELETING BEARINGS SUPPORTING OMBINATION RADIAL AND THRUST LOADS When a bearing supports both a radial load and a thrust load, the loading on the two rows is shared unequally depending on the ratio of thrust to radial load. The use of the (radial factor) and Y (thrust factor) from Table 1 con verts the applied thrust load and radial loads to an equiva lent radial load having the same effect on the life of the bearing as a radial load of this magnitude. The equivalent radial load P = F R + YF A Where: P = Equivalent radial load, lbs. F R = Radial load, lbs. (see Table 1 for allowable slip fit maximum load) F A = Thrust (axial) load, lbs. e = Thrust load to radial load factor (Table 1) = Radial load factor (Table 1) Y = Thrust load factor (Table 1) To find and Y, calculate F A/F R and compare to e for the selected bore size. Determine and Y from Table 1 on page B12-9 depending on whether F A/F R is equal to or less than e, or F A/F R is greater than e. Substitute all known values into the equivalent radial load equation. P (equiva lent radial load) can be used in the life formula to deter mine L 10, or it can be compared to the allowable equivalent radial load ratings for the speed and hours life desired in the easy selection Table 4 on page B SELETING BEARINGS SUPPORTING ONLY THRUST LOADS Spherical Roller generally are not recommended for pure thrust load applications. However, they will per form satisfactorily under very light pure thrust loads. onsult DODGE Application Engineering ( ). SELETING LUBRIATION DODGE S2000 spherical roller bearings are lubricated at the factory with Mobilgrease HP 222 grease. Mobilgrease HP 222 grease is a superior industrial grease using a lithium complex thickener and highly refined base oil. This grease will adequately handle low and medium speeds with low and medium loads at normal temperatures as defined on Table 5 on page B For very low and high speeds, for heavy loads and for low and high temperatures, special greases must be used. ontact DODGE Application Engineering ( ). DODGE engineers will recommend bearings and lubricants for the above unusual conditions. DODGE also has the expertise to custom design and build special bearings for your needs. The only maintenance requirement for DODGE Unitized roller bearings is periodic relubrication at regular intervals as outlined in the appropriate instruction manuals. MISALIGNMENT ONSIDERATIONS In nearly all applications, good design practice requires two bearings supporting the shaft. In cases where three or more bearings are installed, unless precautions are taken to line the bearings up both vertically and horizontally, it is possible to induce heavy loads. In the case of two bearings, alignment is not as critical, especially with DODGE Unitized Spherical Roller. S2000 bearings are designed to allow a maximum of ±1 of static and dynamic misalignment. To ensure good alignment, mounting surfaces must be checked for flatness and must lie in the same plane. When tightening base bolts, each bolt should be alternately tightened in incremental torque values until full torque is achieved to prevent the angular shifting of the pillow block that occurs when one bolt is tightened to its full torque. Shimming may be required to minimize misalignment. UNIFIED SAF PAGE B12-5 PAGE B12-14 B12-8

9 SELETION Table 1: S2000-HD Spherical Roller Inches Basic Bearing Description e F A/F R< e F A/F R>e Max. Allowable Slip Fit Y Y Radial Load F R* lbs. Dynamic apacity () lbs. PAGE B12-5 Static apacity o lbs. Maximum Speed ** Labyrinth RPM PAGE B12-14 TRIDENT Triple Lip RPM 1-3/8 1-7/16 1-1/2 1-11/16 1-3/ ,750 3,750 20,800 20,800 21,000 22,000 3,600 3,360 2,900 2, / ,000 22,000 24,000 3,180 2, / ,860 27,000 29,000 2,700 1, / ,840 39,000 47,500 2,250 1, / / / ,500 11,500 41,500 65,500 53,000 81,500 2,040 1,560 1,490 1, / ,400 83, ,000 1,320 1, / , , ,000 1, / , , ,000 1, * If load exceeds the maximum allowable slip fit load, line- to-line to light press fit of shaft required. Maximum slip fit radial loads apply if recommended shaft sizes are used. ** Maximum speed is dependent on load and ambient conditions, consult DODGE Engineering. After final alignment of the shaft and installation of the housings, tighten both setscrews hand tight, then the setscrews should be tightened alternately and in small increments to the torque specified in Table 2. After 24 hours operation, the setscrews should be retightened to the torque in Table 2 to assure full locking of the inner race to the shaft. are should be taken that the socket key or driver is in good condition with no rounded corners and the key is fully engaged in the setscrew and held square with the setscrew to prevent rounding out of the setscrew socket when applying maximum torque. Table 2: Set Screw Torque Values Set Screw Torque Table Socket Set Screw Tightening Torque 1-3/8-1-3/4 in. 5/16 in. 165 Inch Pounds 1-15/16-2-7/16 in. 3/8 in. 290 Inch Pounds 2-11/16-3-7/16 in. 1/2 in. 620 Inch Pounds 3-15/ /16 in. 5/8 in Inch Pounds Table 3: Lubrication Intervals Lubrication (In Weeks) Read Preceding Paragraphs Before Establishing Lubrication Schedule Hours Run per Day 1 to 250 RPM 251 to 500 RPM 501 to 750 RPM 751 to 1000 RPM 1001 to 1500 RPM 1501 to 2000 RPM 2001 to 2500 RPM 2501 to 3000 RPM Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-9

10 Bearing Reference E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL SELETION Table 4: Easy Selection Table for Double Row Spherical Roller Inches 1-3/8 to 1-1/2 1-11/16 to 1-3/4 1-15/16 to 2 2-3/16 2-7/ /16 to 3 L 10 Life Hours Allowable Equivalent Radial Load Rating (lbs.) at Various Revolutions per Minute ,020 1,200 1,320 1,560 1,750 2,040 2,250 2, ,000 7,498 6,090 5,393 4,626 3,758 3,182 3,034 2,890 2,808 2,671 2,581 2,465 2,393 1,495 2,157 2,122 2,078 30,000 5,393 4,380 3,878 3,327 2,703 2,289 2,182 2,078 2,020 1,921 1,856 1,773 1,721 1,495 1,552 1,526 1,495 40,000 4,947 4,018 3,558 3,052 2,479 2,100 2,002 1,907 1,853 1,762 1,703 1,626 1,579 1,495 1,423 1,400 1,371 60,000 4,380 3,558 3,150 2,703 2,195 1,859 1,773 1,688 1,641 1,560 1,508 1,440 1,398 1,324 1,260 1,240 1, ,000 3,758 3,052 2,703 2,319 1,883 1,595 1,521 1,448 1,407 1,339 1,293 1,235 1,199 1,136 1,081 1,063 1,042 10,000 7,498 6,090 5,393 4,626 3,758 3,182 3,034 2,890 2,808 2,671 2,581 2,465 1,579 2,266 2,157 2,122 30,000 5,393 4,380 3,878 3,327 2,703 2,289 2,182 2,078 2,020 1,921 1,856 1,773 1,579 1,630 1,552 1,526 40,000 4,947 4,018 3,558 3,052 2,479 2,100 2,002 1,907 1,853 1,762 1,703 1,626 1,579 1,495 1,423 1,400 60,000 4,380 3,558 3,150 2,703 2,195 1,859 1,773 1,688 1,641 1,560 1,508 1,440 1,398 1,324 1,260 1, ,000 3,758 3,052 2,703 2,319 1,883 1,595 1,521 1,448 1,407 1,339 1,293 1,235 1,199 1,136 1,081 1,063 10,000 7,930 6,441 5,704 4,893 3,975 3,366 3,209 3,057 2,970 2,825 2,729 1,720 2,531 2,396 2,282 30,000 5,704 4,633 4,102 3,519 2,859 2,421 2,308 2,198 2,136 2,032 1,963 1,720 1,820 1,724 1,641 40,000 5,232 4,250 3,763 3,228 2,622 2,221 2,117 2,017 1,960 1,864 1,801 1,720 1,670 1,581 1,505 60,000 4,633 3,763 3,332 2,859 2,322 1,966 1,875 1,786 1,735 1,650 1,594 1,523 1,479 1,400 1, ,000 3,975 3,228 2,859 2,452 1,992 1,687 1,608 1,532 1,489 1,416 1,368 1,306 1,269 1,201 1,144 10,000 9,733 7,905 7,000 6,005 4,878 4,131 3,939 3,751 3,645 3,467 2,210 3,199 3,106 2,941 30,000 7,000 5,686 5,035 4,319 3,508 2,971 2,833 2,698 2,622 2,494 2,210 2,301 2,234 2,115 40,000 6,421 5,216 4,618 3,962 3,218 2,726 2,599 2,475 2,405 2,288 2,210 2,111 2,050 1,940 60,000 5,686 4,618 4,089 3,508 2,850 2,413 2,301 2,191 2,130 2,026 1,957 1,869 1,815 1, ,000 4,878 3,962 3,508 3,010 2,445 2,070 1,974 1,880 1,827 1,738 1,679 1,603 1,557 1,474 10,000 14,058 11,419 10,111 8,674 7,046 5,967 5,689 5,418 5,266 5,008 4,838 4,621 4,487 30,000 10,111 8,213 7,272 6,239 5,068 4,292 4,092 3,897 3,787 3,602 3,480 3,324 3,227 40,000 9,275 7,534 6,671 5,723 4,649 3,937 3,753 3,575 3,474 3,304 3,192 3,049 2,960 60,000 8,213 6,671 5,907 5,068 4,116 3,486 3,324 3,165 3,076 2,926 2,827 2,700 2, ,000 7,046 5,723 5,068 4,348 3,531 2,991 2,851 2,716 2,639 2,510 2,425 2,316 2,249 10,000 14,959 12,151 10,759 9,230 7,497 6,350 6,054 5,766 3,697 5,329 5,149 4,917 30,000 10,759 8,739 7,738 6,639 5,392 4,567 4,354 4,147 3,697 3,833 3,703 3,537 40,000 9,870 8,017 7,098 6,090 4,946 4,189 3,994 3,804 3,697 3,516 3,397 3,244 60,000 8,739 7,098 6,285 5,392 4,380 3,709 3,537 3,368 3,273 3,113 3,008 2, ,000 7,497 6,090 5,392 4,626 3,758 3,182 3,034 2,890 2,808 2,671 2,580 2,464 10,000 23,611 19,178 16,981 14,569 11,833 10,022 9,555 6,004 8,844 8,411 30,000 16,981 13,793 12,213 10,478 8,511 7,208 6,872 6,004 6,360 6, /16 40,000 15,577 12,653 11,203 9,612 7,807 6,612 6,304 6,004 5,835 5,549 60,000 13,793 11,203 9,920 8,511 6,913 5,855 5,582 5,316 5,166 4, ,000 11,833 9,612 8,511 7,302 5,931 5,023 4,789 4,561 4,432 4,216 Only the labyrinth seal (L seal) may be used to the right of the heavy line. In the light shaded area, a line-to-line to light press fit on the shaft is required. For applications in the dark shaded area, the maximum load for the specific speed is shown. The load does not correspond to the 10 shown at the left. UNIFIED SAF PAGE B12-5 PAGE B12-14 B12-10

11 SELETION Table 4: Easy Selection Table for Double Row Spherical Roller (continued) Inches L 10 Life Hours Allowable Equivalent Radial Load Rating (Lbs.) At Various Revolutions Per Minute ,020 1,200 1,320 1,560 1,750 2,040 2,250 2, ,000 29,919 24,302 21,518 18,461 14,995 12,699 7,988 11,531 11,206 30,000 21,518 17,478 15,476 13,278 10,785 9,134 7,988 8,294 8, /16 40,000 19,739 16,033 14,197 12,180 9,893 8,378 7,988 7,608 7,393 60,000 17,478 14,197 12,571 10,785 8,760 7,419 7,073 6,737 6, ,000 14,995 12,180 10,785 9,252 7,515 6,365 6,068 5,779 5,616 10,000 37,489 30,450 26,963 23,132 18,789 10,498 15,171 14,449 30,000 26,963 21,901 19,392 16,637 13,513 10,498 10,911 10, /16 40,000 24,733 20,090 17,789 15,261 12,396 10,498 10,009 9,533 60,000 21,901 17,789 15,751 13,513 10,976 9,296 8,863 8, ,000 18,789 15,261 13,513 11,593 9,417 7,975 7,603 7,242 10,000 52,628 42,747 37,851 32,473 26,377 14,738 21,298 30,000 37,851 30,745 27,224 23,356 18,971 14,738 15, /16 40,000 34,722 28,203 24,973 21,424 17,402 14,738 14,051 60,000 30,745 24,973 22,112 18,971 15,409 13,050 12, ,000 26,377 21,424 18,971 16,275 13,220 11,196 10,674 Only the labyrinth seal (L seal) may be used to the right of the heavy line. In the light shaded area, a line-to-line to light press fit on the shaft is required. For applications in the dark shaded area, the maximum load for the specific speed is shown. The load does not correspond to the L 10 shown at the left. Table 5: Definition Of Operating onditions For Unitized Spherical Roller LOW SPEED UP TO 20% OF MA. RPM (TABLE 1) MEDIUM SPEED OVER 20% TO 80% OF MA. RPM HIGH SPEED MOVER 80% OF MA. RPM LIGHT LOAD NORMAL LOAD HEAVY LOAD LOW TEMPERATURE UP TO 8% OF (TABLE 1) OVER 8% TO 18% OF OVER 18% OF = DYNAMI APAITY -20 TO -100 F MEDIUM TEMPERATURE OVER 20 F TO 200 F HIGH TEMPERATURE OVER 200 F TO 250 F PAGE B12-5 PAGE B12-14 Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-11

12 Bearing Reference SELETION E-Family Roller 120º 150º 180º Specialty Tapered UNISPHERE II IMPERIAL Table 6: Housing Rating, 2-Bolt, ast Iron* Bore Maximum Recommended Housing ap Loads, lb /8 to 1-1/ /8 to 1-3/ /16 to / / /16 to /16 to 3-7/ / Table 7: Housing Rating, 4-Bolt, ast Iron* Bore Maximum Recommended Housing ap Loads, lb / / / /16 to / / / / * When utilizing heavy cap loads on pillow block housings, the installation must adhere to the following procedures: 1. The pillow block base bolts must be of high strength (Grade 8) bolts and properly tightened to mounting structure. 2. Stop bars (shear strips) should be used against the plummer block where side loads are encountered. 3. In all cases where loads are heavy, the L 10 life of the bearing should be checked for proper selection and life requirements. UNIFIED SAF PAGE B12-5 PAGE B12-14 B12-12

13 SELETION S2000-HD Bearing Reference Table 8: Steel Housed S Housing Ratings* Maximum Recommended Housing Loads, lb s Basic Bearing Description P2B P4B 1-3/8 1-7/16 1-1/2 1-11/16 1-3/4 1-15/ / / / / / / / / * It is important to note that the values listed above are housing fracture loads from variou applied directions. These loads may exceed bearing, mounting bolt and/or shaft capacities. Applications subject to heavy housing loads, particularly shock loads, must adhere to the following procedures: (1) The pillow block base bolts must be of high strength (Grade 8) bolts and properly tightened to mounting structure. (2) Stop bars (shear strips) should be used against the plummer block where side loads are encountered. (3) In all cases where loads are heavy, the L 10 life of the bearing should be checked for proper selection and life requirements., PAGE B12-5 PAGE B12-14 UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-13

14 Bearing Reference Pillow Block 2-BOLT BASE - INH E-Family Roller G 30 NOTE: All sizes use a 1/8-27 NPT hydraulic grease fitting Specialty Tapered F BOLT DIA. H M J D MIN D MA B UNISPHERE II IMPERIAL L S A L S A R Y MA Z MIN EPANSION NON-EPANSION UNIFIED SAF B12-14

15 Pillow Block 2-BOLT BASE - INH Bearing Reference Bearing Inch TRIDENT Seal Labyrinth Seal Non-Expansion Expansion Non-Expansion Expansion Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name 1-3/ P2B-S2-106R P2B-S2-106RE P2B-S2-106L P2B-S2-106LE / P2B-S2-107R P2B-S2-107RE P2B-S2-107L P2B-S2-107LE 1-1/ P2B-S2-108R P2B-S2-108RE P2B-S2-108L P2B-S2-108LE / P2B-S2-111R P2B-S2-111RE P2B-S2-111L P2B-S2-111LE 1-3/ P2B-S2-112R P2B-S2-112RE P2B-S2-112L P2B-S2-112LE / P2B-S2-115R P2B-S2-115RE P2B-S2-115L P2B-S2-115LE P2B-S2-200R P2B-S2-200RE P2B-S2-200L P2B-S2-200LE / P2B-S2-203R P2B-S2-203RE P2B-S2-203L P2B-S2-203LE / P2B-S2-207R P2B-S2-207RE P2B-S2-207L P2B-S2-207LE 2-11/ P2B-S2-211R P2B-S2-211RE P2B-S2-211L P2B-S2-211LE / P2B-S2-215R P2B-S2-215RE P2B-S2-215L P2B-S2-215LE P2B-S2-300R P2B-S2-300RE P2B-S2-300L P2B-S2-300LE / P2B-S2-307R P2B-S2-307RE P2B-S2-307L P2B-S2-307LE / P2B-S2-315R P2B-S2-315RE P2B-S2-315L P2B-S2-315LE D F A B Bolt G H J L M R S Total Min Max Dia. Exp. Y Z 1-3/8 1-7/16 1-1/2 1-11/16 1-3/ /2 1/ /16 1/ / / / / / / / / / / / / /4 7/ /4 1/ / / UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-15

16 Bearing Reference Pillow Block with Type E Dimensions 2-BOLT E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-16

17 Pillow Block with Type E Dimensions 2-BOLT Bearing Reference Bearing Series * TRIDENT Seal Labyrinth Seal Non Expansion Expansion Non Expansion Expansion Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name / EP2B-S2-106R EP2B-S2-106RE EP2B-S2-106L EP2B-S2-106LE 1-7/ EP2B-S2-107R EP2B-S2-107RE EP2B-S2-107L EP2B-S2-107LE / EP2B-S2-111R EP2B-S2-111RE EP2B-S2-111L EP2B-S2-111LE / EP2B-S2-115R EP2B-S2-115RE EP2B-S2-115L EP2B-S2-115LE EP2B-S2-200R EP2B-S2-200RE EP2B-S2-200L EP2B-S2-200LE / EP2B-S2-203R EP2B-S2-203RE EP2B-S2-203L EP2B-S2-203LE / EP2B-S2-207R EP2B-S2-207RE EP2B-S2-207L EP2B-S2-207LE 2-11/ EP2B-S2-211R EP2B-S2-211RE EP2B-S2-211L EP2B-S2-211LE / EP2B-S2-215R EP2B-S2-215RE EP2B-S2-215L EP2B-S2-215LE EP2B-S2-300R EP2B-S2-300RE EP2B-S2-300L EP2B-S2-300LE / EP2B-S2-307R EP2B-S2-307RE EP2B-S2-307L EP2B-S2-307LE *onsult Dodge For s Not Listed A B# # Min D Max F Bolt Dia. G# H# J# L M R S 1-3/8 1-7/ / / / / / / / / / / / / / / / / / / / / / / /4 7/ /4 1/ /2-13 1/ Notes: A And R Dimensions Do Not Include Y Dimension # Reference Dimension Only Total Exp. Y Z Set Screw S/S Torque In/Lbs UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-17

18 Bearing Reference Steel -HD Pillow Block 2-Bolt E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-18

19 SELETION Steel -HD Pillow Block 2-Bolt Bearing Reference Dodge Non-Expansion Dodge Expansion Part No. Description Part No. Description 1-3/ SP2B-S2-106R SP2B-S2-106RE 1-7/ SP2B-S2-107R SP2B-S2-107RE 1-1/ SP2B-S2-108R SP2B-S2-108RE 1-11/ SP2B-S2-111R SP2B-S2-111RE 1-3/ SP2B-S2-112R SP2B-S2-112RE 1-15/ SP2B-S2-115R SP2B-S2-115RE SP2B-S2-200R SP2B-S2-200RE 2-3/ SP2B-S2-203R SP2B-S2-203RE 2-7/ SP2B-S2-207R SP2B-S2-207RE 2-11/ SP2B-S2-211R SP2B-S2-211RE 2-15/ SP2B-S2-215R SP2B-S2-215RE SP2B-S2-300R SP2B-S2-300RE 3-7/ SP2B-S2-307R SP2B-S2-307RE 3-15/ SP2B-S2-315R SP2B-S2-315RE A B Min D Max F Bolt Dia. G H J L M R S 1-3/8 1-7/16 1-1/2 1-11/16 1-3/ /2 1/ /16 1/ / / / / / / / / / / / / /4 7/ /4 1/ / / "A" & "R" Dimensions Do Not Include "Y" Dimension PAGE B12-5 " Total Exp" PAGE B12-14 Y Z UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-19

20 Bearing Reference SELETION Steel -HD Pillow Block 2-Bolt With Type E Dimensions E-Family Roller G 1/8-27 NPT F J Specialty Tapered H M D MIN D MA B UNISPHERE II IMPERIAL L S L A HSG S L A HSG R Y MA Z MIN EPANSION NON-EPANSION UNIFIED SAF PAGE B12-5 PAGE B12-14 B12-20

21 Steel -HD Pillow Block 2-BOLT With Type E Dimensions Bearing Reference Dodge Non-Expansion Dodge Expansion Part No. Description Part No. Description 1-3/ SEP2B-S2-106R SEP2B-S2-106RE 1-7/ SEP2B-S2-107R SEP2B-S2-107RE 1-11/ SEP2B-S2-111R SEP2B-S2-111RE 1-15/ SEP2B-S2-115R SEP2B-S2-115RE SEP2B-S2-200R SEP2B-S2-200RE 2-3/ SEP2B-S2-203R SEP2B-S2-203RE 2-7/ SEP2B-S2-207R SEP2B-S2-207RE 2-11/ SEP2B-S2-211R SEP2B-S2-211RE 2-15/ SEP2B-S2-215R SEP2B-S2-215RE SEP2B-S2-300R SEP2B-S2-300RE 3-7/ SEP2B-S2-307R SEP2B-S2-307RE A B Min D Max F Bolt Dia G H J L M R S 1-3/8 1-7/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / A & R Dimensions Do Not Include Y Dimension Total Exp Y Z Set Screw SS Torque In/lbs UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-21

22 Bearing Reference Pillow Block 4-BOLT BASE E-Family Roller S L HSG S L HSG L A L A R Specialty Tapered E F BOLT DIA. G J 1-15/16 THRU 3-15/16" ONSTRUTION EPANSION 1-15/16 THRU 3-15/16" ONSTRUTION NON-EPANSION H M S L HSG S L HSG UNISPHERE II IMPERIAL D MIN D MA B L A 4-7/16 THRU 4-15/16" ONSTRUTION EPANSION L A R 4-7/16 THRU 4-15/16" ONSTRUTION NON-EPANSION UNIFIED SAF B12-22

23 Pillow Block 4-BOLT BASE Bearing Reference Bearing Inch TRIDENT Seal Labyrinth Seal Non-Expansion Expansion Non-Expansion Expansion Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name / P4B-S2-115R P4B-S2-115RE P4B-S2-115L P4B-S2-115LE P4B-S2-200R P4B-S2-200RE P4B-S2-200L P4B-S2-200LE / P4B-S2-203R P4B-S2-203RE P4B-S2-203L P4B-S2-203LE / P4B-S2-207R P4B-S2-207RE P4B-S2-207L P4B-S2-207LE 2-11/ P4B-S2-211R P4B-S2-211RE P4B-S2-211L P4B-S2-211LE / P4B-S2-215R P4B-S2-215RE P4B-S2-215L P4B-S2-215LE P4B-S2-300R P4B-S2-300RE P4B-S2-300L P4B-S2-300LE / P4B-S2-307R P4B-S2-307RE P4B-S2-307L P4B-S2-307LE / P4B-S2-315R P4B-S2-315RE P4B-S2-315L P4B-S2-315LE / P4B-S2-407R P4B-S2-407RE P4B-S2-407L P4B-S2-407LE / P4B-S2-415R P4B-S2-415RE P4B-S2-415L P4B-S2-415LE A B Min D Max F E Bolt G H J L M R S Dia. 1-15/ / / / / / / / / / / / /8 3/ /4 1/ / / / / / /8 N/A N/A 4-15/ / /8 N/A N/A Total Exp. Y Z UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-23

24 Bearing Reference Pillow Block with Type E Dimensions 4-BOLT E-Family Roller W L S HSG L A W L S HSG L A R Y MA Z MIN Specialty Tapered G 1/8-27 NPT 2-7/16 THRU 3-15/16" ONSTRUTION EPANSION 2-7/16 THRU 3-15/16" ONSTRUTION NON-EPANSION UNISPHERE II IMPERIAL E D MIN D MA B F H M J L W S HSG L A 4-7/16 THRU 4-15/16" ONSTRUTION EPANSION W L S HSG L A R 4-7/16 THRU 4-15/16" ONSTRUTION NON-EPANSION UNIFIED SAF B12-24

25 Pillow Block with Type E Dimensions 4-BOLT TRIDENT Seal Labyrinth Seal Bearing Non Expansion Expansion Non Expansion Expansion Series * Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name / EP4B-S2-207R EP4B-S2-207RE EP4B-S2-207L EP4B-S2-207LE 2-11/ EP4B-S2-211R EP4B-S2-211RE EP4B-S2-211L EP4B-S2-211LE / EP4B-S2-215R EP4B-S2-215RE EP4B-S2-215L EP4B-S2-215LE EP4B-S2-300R EP4B-S2-300RE EP4B-S2-300L EP4B-S2-300LE / EP4B-S2-307R EP4B-S2-307RE EP4B-S2-307L EP4B-S2-307LE / EP4B-S2-315R EP4B-S2-315RE EP4B-S2-315L EP4B-S2-315LE / EP4B-S2-407R EP4B-S2-407RE EP4B-S2-407L EP4B-S2-407LE / EP4B-S2-415R EP4B-S2-415RE EP4B-S2-415L EP4B-S2-415LE *onsult Dodge For s Not Listed A B# # Min D Max F E Bolt G # H # J # L M R S Total Y Z Dia. Exp. 2-7/ / / / / / / /8 3/ /4 1/ /2 1/ / / / / / / /8 N/A N/A 5/ / / /8 N/A N/A 5/ Notes: A And R Dimensions Do Not Include Y Dimension # Reference Dimension Only Set Screw S/S Torque In/Lbs Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-25

26 Bearing Reference Steel -HD Pillow Block 4-Bolt E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-26

27 Steel -HD Pillow Block 4-Bolt Bearing Reference Dodge Non-Expansion Dodge Expansion Dodge Part No. Description Dodge Part No. Description 2-7/ SP4B-S2-207R SP4B-S2-207RE 2-11/ SP4B-S2-211R SP4B-S2-211RE 2-15/ SP4B-S2-215R SP4B-S2-215RE SP4B-S2-300R SP4B-S2-300RE 3-7/ SP4B-S2-307R SP4B-S2-307RE 3-15/ SP4B-S2-315R SP4B-S2-315RE 4-7/ SP4B-S2-407R SP4B-S2-407RE 4-15/ SP4B-S2-415R SP4B-S2-415RE A B Min D Max E F Bolt Dia. G H J L M R S 2-7/ / / / / / / / / / / / / / / / / / / A & R Dimensions Do Not Include Y Dimension Total Exp Y Z UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-27

28 Bearing Reference Steel S2000-HD Pillow Block 4-Bolt With Type E Dimensions E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-28

29 Steel S2000-HD Pillow Block 4-Bolt With Type E Dimensions Dodge Non-Expansion Dodge Expansion Dodge Part No. Description Dodge Part No. Description 2-7/ SEP4B-S2-207R SEP4B-S2-207RE 2-11/ SEP4B-S2-211R SEP4B-S2-211RE 2-15/ SEP4B-S2-215R SEP4B-S2-215RE SEP4B-S2-300R SEP4B-S2-300RE 3-7/ SEP4B-S2-307R SEP4B-S2-307RE 3-15/ SEP4B-S2-315R SEP4B-S2-315RE 4-7/ SEP4B-S2-407R SEP4B-S2-407RE 4-15/ SEP4B-S2-415R SEP4B-S2-415RE A B D Min 2-7/ / / / / / / / / / / / / A & R Dimensions Do Not Include Y Dimension # Reference Dimension Only J L M R S 2-7/ / / / / / / / / / / / / / / / / /8 N/A N/A 5/ A & R Dimensions Do Not Include Y Dimension D Max Total Exp E Y F Bolt Dia Z G Set Screw H S/S Torque In/Lbs Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-29

30 Bearing Reference Flange Bearing - Round B ØDD B ØDD E-Family Roller Specialty Tapered D F F D UNISPHERE II IMPERIAL J L 1-3/8" THRU 1-1/2" ONSTRUTION A E Y MA Z MIN J L 1-11/16" - 3" ONSTRUTION A E P H EPANSION H NON-EPANSION UNIFIED SAF B12-30

31 Flange Bearing - Round Bearing Inch TRIDENT Seal Labyrinth Seal Non-Expansion Expansion Non-Expansion Expansion Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name 1-3/ F3R-S2-106R F3R-S2-106RE F3R-S2-106L F3R-S2-106LE / F3R-S2-107R F3R-S2-107RE F3R-S2-107L F3R-S2-107LE 1-1/ F3R-S2-108R F3R-S2-108RE F3R-S2-108L F3R-S2-108LE / F4R-S2-111R F4R-S2-111RE F4R-S2-111L F4R-S2-111LE 1-3/ F4R-S2-112R F4R-S2-112RE F4R-S2-112L F4R-S2-112LE / F4R-S2-115R F4R-S2-115RE F4R-S2-115L F4R-S2-115LE F4R-S2-200R F4R-S2-200RE F4R-S2-200L F4R-S2-200LE / F4R-S2-203R F4R-S2-203RE F4R-S2-203L F4R-S2-203LE / F4R-S2-207R F4R-S2-207RE F4R-S2-207L F4R-S2-207LE 2-11/ F4R-S2-211R F4R-S2-211RE F4R-S2-211L F4R-S2-211LE / F4R-S2-215R F4R-S2-215RE F4R-S2-215L F4R-S2-215LE F4R-S2-300R F4R-S2-300RE F4R-S2-300L F4R-S2-300LE 1-3/8 A B D DD E F Bolt Dia. H J L P 1-7/ /2* / /2 1-11/16 1-3/4 1-15/ /2** / /2** / / /8** / / /8** / / /16 3 * 3 Equally spaced bolt holes ** 4 Equally spaced bolt holes /4** / Total Exp. Y Z Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-31

32 Bearing Reference Flange Bearing - Square B E-Family Roller D N Specialty Tapered D B F UNISPHERE II IMPERIAL J L G A K H Y MA Z MIN J L G P A H EPANSION NON-EPANSION UNIFIED SAF B12-32

33 Flange Bearing - Square Bearing Inch TRIDENT Seal Labyrinth Seal Non-Expansion Expansion Non-Expansion Expansion Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name 1-3/ F4S-S2-106R F4S-S2-106RE F4S-S2-106L F4S-S2-106LE / F4S-S2-107R F4S-S2-107RE F4S-S2-107L F4S-S2-107LE 1-1/ F4S-S2-108R F4S-S2-108RE F4S-S2-108L F4S-S2-108LE / F4S-S2-111R F4S-S2-111RE F4S-S2-111L F4S-S2-111LE 1-3/ F4S-S2-112R F4S-S2-112RE F4S-S2-112L F4S-S2-112LE / F4S-S2-115R F4S-S2-115RE F4S-S2-115L F4S-S2-115LE F4S-S2-200R F4S-S2-200RE F4S-S2-200L F4S-S2-200LE / F4S-S2-203R F4S-S2-203RE F4S-S2-203L F4S-S2-203LE / F4S-S2-207R F4S-S2-207RE F4S-S2-207L F4S-S2-207LE 2-11/ F4S-S2-211R F4S-S2-211RE F4S-S2-211L F4S-S2-211LE / F4S-S2-215R F4S-S2-215RE F4S-S2-215L F4S-S2-215LE F4S-S2-300R F4S-S2-300RE F4S-S2-300L F4S-S2-300LE / F4S-S2-307R F4S-S2-307RE F4S-S2-307L F4S-S2-307LE / F4S-S2-315R F4S-S2-315RE F4S-S2-315L F4S-S2-315LE F A B D Bolt G H J K L N P Dia 1-3/8 1-7/16 1-1/2 1-11/16 1-3/ /2 1/ /16 1/ / / / / / / / / / / / / /4 3/ /4 1/ / / / Total Exp. Y Z Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-33

34 Bearing Reference Flange Bearing - Square with Type E Dimensions E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-34

35 Flange Bearing - Square with Type E Dimensions Bearing Series * TRIDENT Seal Labyrinth Seal Non Expansion Expansion Non Expansion Expansion Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name / EF4B-S2-106R EF4B-S2-106RE EF4B-S2-106L EF4B-S2-106LE 1-7/ EF4B-S2-107R EF4B-S2-107RE EF4B-S2-107L EF4B-S2-107LE / EF4B-S2-111R EF4B-S2-111RE EF4B-S2-111L EF4B-S2-111LE / EF4B-S2-115R EF4B-S2-115RE EF4B-S2-115L EF4B-S2-115LE EF4B-S2-200R EF4B-S2-200RE EF4B-S2-200L EF4B-S2-200LE / EF4B-S2-203R EF4B-S2-203RE EF4B-S2-203L EF4B-S2-203LE / EF4B-S2-207R EF4B-S2-207RE EF4B-S2-207L EF4B-S2-207LE 2-11/ EF4B-S2-211R EF4B-S2-211RE EF4B-S2-211L EF4B-S2-211LE / EF4B-S2-215R EF4B-S2-215RE EF4B-S2-215L EF4B-S2-215LE EF4B-S2-300R EF4B-S2-300RE EF4B-S2-300L EF4B-S2-300LE / EF4B-S2-307R EF4B-S2-307RE EF4B-S2-307L EF4B-S2-307LE / EF4B-S2-315R EF4B-S2-315RE EF4B-S2-315L EF4B-S2-315LE / EF4B-S2-407R EF4B-S2-407RE EF4B-S2-407L EF4B-S2-407LE *onsult Dodge For s Not Listed F A B # # D DD Bolt G H # J # L N P Total Y Z Dia. Exp. 1-3/8 1-7/ / / / / / / / / / / / / / / / / / / / / / / /4 3/ /4 1/ /2-13 1/ / / / / / / /8 N/A N/A 5/ Note(S): P Dimension Is For Non-Expansion Only A And P Dimensions Do Not Include Y Dimension # - Reference Dimensions Only Set Screw S/S Torque In/Lbs Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-35

36 Bearing Reference Steel -HD Flange 4-Bolt E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-36

37 Steel -HD Flange 4-Bolt Dodge Non-Expansion Dodge Expansion Dodge Part No. Description Dodge Part No. Description 1-3/ SF4S-S2-106R SF4S-S2-106RE 1-7/ SF4S-S2-107R SF4S-S2-107RE 1-1/ SF4S-S2-108R SF4S-S2-108RE 1-11/ SF4S-S2-111R SF4S-S2-111RE 1-3/ SF4S-S2-112R SF4S-S2-112RE 1-15/ SF4S-S2-115R SF4S-S2-115RE SF4S-S2-200R SF4S-S2-200RE 2-3/ SF4S-S2-203R SF4S-S2-203RE 2-7/ SF4S-S2-207R SF4S-S2-207RE 2-11/ SF4S-S2-211R SF4S-S2-211RE 2-15/ SF4S-S2-215R SF4S-S2-215RE SF4S-S2-300R SF4S-S2-300RE 3-7/ SF4S-S2-307R SF4S-S2-307RE 3-15/ SF4S-S2-315R SF4S-S2-315RE A B D F Bolt Dia. G H J K L N P 1-3/8 1-7/16 1-1/2 1-11/16 1-3/ /2 1/ /16 1/ / / / / / / / / / / / / /4 3/ /4 1/ / / P Dimension Is For Non-Expansion Only A & P Dimensions Do Not Include Y Dimension Total Exp Y Z Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-37

38 Bearing Reference Piloted Flange E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-38

39 Piloted Flange Bearing Inch TRIDENT Seal Labyrinth Seal Non-Expansion Expansion Non-Expansion Expansion Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name 1-3/ F-S2-106R F-S2-106RE F-S2-106L F-S2-106LE / F-S2-107R F-S2-107RE F-S2-107L F-S2-107LE 1-1/ F-S2-108R F-S2-108RE F-S2-108L F-S2-108LE / F-S2-111R F-S2-111RE F-S2-111L F-S2-111LE 1-3/ F-S2-112R F-S2-112RE F-S2-112L F-S2-112LE / F-S2-115R F-S2-115RE F-S2-115L F-S2-115LE F-S2-200R F-S2-200RE F-S2-200L F-S2-200LE / F-S2-203R F-S2-203RE F-S2-203L F-S2-203LE / F-S2-207R F-S2-207RE F-S2-207L F-S2-207LE 2-11/ F-S2-211R F-S2-211RE F-S2-211L F-S2-211LE / F-S2-215R F-S2-215RE F-S2-215L F-S2-215LE F-S2-300R F-S2-300RE F-S2-300L F-S2-300LE / F-S2-307R F-S2-307RE F-S2-307L F-S2-307LE / F-S2-315R F-S2-315RE F-S2-315L F-S2-315LE /16 ** F-S2-407R F-S2-407RE F-S2-407L F-S2-407LE /16 ** F-S2-415R F-S2-415RE F-S2-415L F-S2-415LE 1-3/8 1-7/16 1-1/2 1-11/16 1-3/4 1-15/16 2 F A B D DD E Bolt G H * K L M N P Q Dia / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /4** / /8 N/A N/A 4-15/ /8** / /8 N/A N/A ** Housing utilize 6 bolts equally spaced * +.000/-.002 Total Exp. Y Z Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-39

40 Bearing Reference Piloted Flange with Type E Dimensions E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-40

41 Piloted Flange with Type E Dimensions Bearing Series * TRIDENT SEAL Labyrinth Seal Non Expansion Expansion Non Expansion Expansion Part No. Part Name Part No. Part Name Part No. Part Name Part No. Part Name / F-S2-106R F-S2-106RE F-S2-106L F-S2-106LE 1-7/ F-S2-107R F-S2-107RE F-S2-107L F-S2-107LE / F-S2-111R F-S2-111RE F-S2-111L F-S2-111LE / F-S2-115R F-S2-115RE F-S2-115L F-S2-115LE F-S2-200R F-S2-200RE F-S2-200L F-S2-200LE / F-S2-203R F-S2-203RE F-S2-203L F-S2-203LE / F-S2-207R F-S2-207RE F-S2-207L F-S2-207LE 2-11/ F-S2-211R F-S2-211RE F-S2-211L F-S2-211LE / F-S2-215R F-S2-215RE F-S2-215L F-S2-215LE F-S2-300R F-S2-300RE F-S2-300L F-S2-300LE / F-S2-307R F-S2-307RE F-S2-307L F-S2-307LE / F-S2-315R F-S2-315RE F-S2-315L F-S2-315LE / EF-S2-407R EF-S2-407RE EF-S2-407L EF-S2-407LE / EF-S2-415R EF-S2-415RE EF-S2-415L EF-S2-415LE A B # # D DD E # F Bolt Dia. G H # K ## L M N P Q # Total Exp. Y Z Set S/S Screw Torque In/Lbs 1-3/8 1-7/ / / / / / / / / / / / / / / / / / / / / / / / / / / / /8 3/ /8-11 3/ /4 1/ /2 1/ / / / / / / /4 ** / /8 N/A N/A 5/ / /8 ** / /8 N/A N/A 5/ ## Note(S): P And G Dimensions Are For Non-Expansion Only A And P Dimensions Do Not Include Y Dimension # - Reference Dimension Only Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-41

42 Bearing Reference Wide Slot Take-Up 1-3/8 THRU 2-3/16 INH E-Family Roller D F Specialty Tapered N M H G K J B E UNISPHERE II IMPERIAL L R S A T EPANSION L R S A T NON-EPANSION Y MA Z MIN UNIFIED SAF B12-42

43 Wide Slot Take-Up 1-3/8 THRU 2-3/16 INH Bearing TRIDENT Seal Take-Up Non-Expansion Expansion Frame Inch Part No. Part Name Part No. Part Name 1-3/ WSTU-S2-106R WSTU-S2-106RE /16 P WSTU-S2-107R WSTU-S2-107RE 1-1/ WSTU-S2-108R WSTU-S2-108RE / WSTU-S2-111R WSTU-S2-111RE P / WSTU-S2-112R WSTU-S2-112RE / WSTU-S2-115R WSTU-S2-115RE P WSTU-S2-200R WSTU-S2-200RE /16 P WSTU-S2-203R WSTU-S2-203RE A B D E F G H J K 1-3/8 1-7/16 1-1/2 1-11/16 1-3/ /8 1-1/ / / / / L M N R S T Total Exp 1-3/8 1-7/16 1-1/2 1-11/16 1-3/ /16 1/ / / / / Y Z Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-43

44 Bearing Reference Wide Slot Take-Up 2-7/16 THRU 4-15/16 INH E-Family Roller S R S R Specialty Tapered D F L A L A UNISPHERE II IMPERIAL N M B E H G K J L T 1-3/8 THRU 3-15/16" ONSTRUTION S R T A 4-7/16 THRU 4-15/16" ONSTRUTION T 1-3/8 THRU 3-15/16" ONSTRUTION L S R T A 4-7/16 THRU 4-15/16" ONSTRUTION UNIFIED SAF B12-44

45 Wide Slot Take-Up 2-7/16 THRU 4-15/16 INH Bearing Inch Take-Up Frame Non-Expansion TRIDENT Seal Expansion Part Number Part Name Part Number Part Name /16 P WSTU-S2-207R WSTU-S2-207RE 2-11/ WSTU-S2-211R WSTU-S2-211RE /16 P WSTU-S2-215R WSTU-S2-215RE WSTU-S2-300R WSTU-S2-300RE /16 P WSTU-S2-307R WSTU-S2-307RE /16 P WSTU-S2-315R WSTU-S2-315RE /16 P WSTU-S2-407R WSTU-S2-407RE /16 P WSTU-S2-415R WSTU-S2-415RE A B D E F G H J K 2-7/ / / / / /8 1-7/ / / / / / / L M N R S T Total Exp 2-7/ / / / / /4 1/ / / / /8 N/A N/A 4-15/ /8 N/A N/A See Page B15-20 for P Take-Up Frame Y Z Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-45

46 Bearing Reference TPHU Take-Up E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL UNIFIED SAF B12-46

47 TPHU Take-Up Bearing Inch 1-15/16 Take-Up Frame TRIDENT Seal Non-Expansion Expansion Part Number Part Name Part Number Part Name TPHU-S2-115R TPHU-S2-115RE TP10 TPHU TPHU-S2-200R TPHU-S2-200RE /16 TP30 TPHU TPHU-S2-203R TPHU-S2-203RE /16 TP40 TPHU TPHU-S2-207R TPHU-S2-207RE 2-11/ TPHU-S2-211R TPHU-S2-211RE /16 TP40 TPHU TPHU-S2-215R TPHU-S2-215RE TPHU-S2-300R TPHU-S2-300RE /16 TP50 TPHU TPHU-S2-307R TPHU-S2-307RE /16 TP60 TPHU TPHU-S2-315R TPHU-S2-315RE /16 N/A TPHU TPHU-S2-407R TPHU-S2-407RE /16 N/A TPHU TPHU-S2-415R TPHU-S2-415RE A B D E F G H J K L M 1-15/ / / / / / / / / See Page B19-20 Thru B19-25 For TP And TPHU Frames 1-15/16 N P Q R S T U V W Total Exp / / / / / / / / See Page B19-20 Thru B19-25 For TP And TPHU Frames Y Z Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-47

48 Bearing Reference Bearing Insert B ONTAT SEAL B E-Family Roller D F SHAFT DIA D F SHAFT DIA Specialty Tapered A E A E 1-3/8 THRU 3-15/16" ONSTRUTION 4-7/16 THRU 4-15/16" ONSTRUTION UNISPHERE II IMPERIAL A D B F SHAFT DIA LABYRINTH SEAL E A D B F SHAFT DIA E UNIFIED SAF 1-3/8 THRU 3-15/16" ONSTRUTION 4-7/16 THRU 4-15/16" ONSTRUTION B12-48

49 Bearing Insert Bearing TRIDENT Seal Labyrinth Seal Part Number Part Name Part Number Part Name 1-3/ INS-S2-106R INS-S2-106L / INS-S2-107R INS-S2-107L 1-1/ INS-S2-108R INS-S2-108L / INS-S2-111R INS-S2-111L 1-3/ INS-S2-112R INS-S2-112L / INS-S2-115R INS-S2-115L INS-S2-200R INS-S2-200L / INS-S2-203R INS-S2-203L / INS-S2-207R INS-S2-207L 2-11/ INS-S2-211R INS-S2-211L / INS-S2-215R INS-S2-215L INS-S2-300R INS-S2-300L / INS-S2-307R INS-S2-307L / INS-S2-315R INS-S2-315L / INS-S2-407R INS-S2-407L / INS-S2-415R INS-S2-415L A B D E 1-3/8 1-7/16 1-1/2 1-11/16 1-3/ / / / / / / / / / Bearing Reference UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-49

50 Bearing Reference Steel Open End overs E-Family Roller Specialty Tapered UNISPHERE II IMPERIAL Dodge Part No. Front End Backside S2000 & S2000-HD E-S2000 & ES2000-HD S2000 & S2000-HD E-S2000 & ES2000-HD Description Dodge Part No. Description Dodge Part No. Description Dodge Part No. Description 1-3/ S2EO S2EO S2IPBEO S2IPBEO / S2EO S2EO S2IPBEO S2IPBEO / S2EO S2EO S2IPBEO ES2IPBEO / S2EO S2EO S2IPBEO S2IPBEO / S2EO S2EO S2IPBEO ES2IPBEO / S2EO S2EO S2IPBEO S2IPBEO S2EO S2EO S2IPBEO S2IPBEO / S2EO S2EO S2IPBEO S2IPBEO / S2IPEO S2IPEO S2IPBEO S2IPBEO / S2EO S2EO S2IPBEO S2IPBEO / S2EO S2EO S2IPBEO S2IPBEO S2EO S2EO S2IPBEO S2IPBEO / S2IPEO S2IPEO S2IPBEO S2IPBEO / S2IPEO S2IPEO S2IPBEO S2IPBEO / S2IPEO S2IPEO S2BEO S2BEO / S2IPEO S2IPEO S2BEO S2BEO UNIFIED SAF B12-50

51 Steel losed End overs Bearing Reference S2000 & S2000-HD E-S2000 & ES2000-HD Dodge Part No. Description Dodge Part No. Description 1-3/8 to 1-1/ S2E IPE /16 to 1-3/ S2E IPE /16 to S2E IPE10 2-3/ S2E IPE11 2-7/ S2E IPE /16 to S2E IPE15 3-7/ S2IPE S2IPE / S2IPE S2IPE20 4-7/ S2IPE S2IPE / S2IPE S2IPE26 UNIFIED SAF IMPERIAL UNISPHERE II Specialty Tapered E-Family Roller B12-51