INTERNATIONAL ARMOR CORPORATION BODY ARMOR AND ACCESSORIES

Transcription

1 INTERNATIONAL ARMOR CORPORATION BODY ARMOR AND ACCESSORIES Call Toll Free:

2 Vests Concealable INTERNATIONAL ARMOR CORPORATION T-Armor NIJ STANDARDS BALLISTIC CHART Threat Level Caliber Bullet Bullet Description Nominal Bullet Diameter Acceptable Manufacturer IIA 9 mm Luger 8.0 g (124 gr) FMJ RN 9 mm (.355 in) Remington S&W 11.7 g (180 gr) FMJ 10 mm (.400 in) Remington II 9 mm Luger 8.0 g (124 gr) FMJ RN 9 mm (.355 in) Remington Mag 10.2 g (158 gr) JSP 9.1 mm (.357 in) Remington IIIA 357 SIG 8.1 g (124 gr) TMJ 9.0 mm (.355 in) Speer 4362 Bullet Model Number.44 Mag 15.6 g (240 gr) JHP 10.9 mm (.429 in) Speer 4453 or 4736 ** III 7.62 mm NATO 9.6 g (147 gr) FMJ-SPIRE PT BT * 7.62 mm (.308 in) *** *** IV M2 AP 10.8 g (166 gr) FMJ-SPIRE PT AP* 7.62 mm (.308 in) May be obtained from U.S. Military M2 AP ammunition * Verify that jacket is ferrous (use of magnet acceptable). ** Note: These two models are the same bullet but sold in different quantities. *** Bullet may be obtained from U.S. military/nato M80 ammunition, or from other manufacturers meeting the specifications for the projectile in the M80 cartridge. s Available in NIJ Level IIA, II, and IIIA Ballistic/stab-shank armor upon request 6 x 8, 15.24cm x 20.32cm pocket size Choice of soft trauma plate or steel plate included Available in male and female sizing Small (34-36) Medium (38-40) (42-44) X (46-48) XX (50-52) XXX (54-56) XXXX (58-60) Available in custom sizes Vests come in choice of short, regular, long lengths White, Black Designed to maximize ventilation while minimizing heat Cool mesh carrier increases air circulation and absorbs moisture to keep cool and dry Snug fit and contour design allows for maximum conceal-ability FREQUENTLY ASKED QUESTIONS ABOUT BODY ARMOR Q. How does body armor work? A. When a bullet strikes a body armor panel, the fibers absorb and disperse the energy of the impact across a generalized area. Most concealable body armor is made of a number of layers. These layers assist in the energy dispersion process and help to reduce the effects of blunt trauma caused by the force of impact energy that is delivered by the projectile. Q. How long does body armor last? A. There are a number of factors that can influence the service life of body armor. The National Institute of Justice (NIJ) has done research (detailed in the publication entitled Old Armor Tests As Good As New and available from NLECTC at or ) that indicates that age is not the only determining factor. Other factors to consider include: how regularly the armor was worn; how it was cared for; whether the armor fit the wearer properly (most people lose or gain weight over a period of years); and the overall condition of the armor (do the fasteners still work properly, and so on). We encourage departments that issue body armor to have a routine inspection program for body armor, just as they would for weapons, vehicles, and other types of issued equipment. Q. What types of materials are used to make body armor? A. There are a number of materials used in the manufacturing of body armor. Concealable, or soft body armor can be made from a number of different types of woven or non woven materials. The most recognized of these is Kevlar, which is made by DuPont. Other materials include Spectra, which is made by AlliedSignal, and Twaron, made by Akzo Nobel. These materials are manufactured in a variety of styles and weaves. Hard armor plates can be made from a number of materials, including metals, ceramics, and other composite materials. Q. Which ballistic material is better? A. Each fiber has its own advantages and disadvantages. The construction of the vest (what type or types of materials and the number of layers of each material used) and the weave of the fibers can influence the performance of the vest. To determine which is best for you, look at and try out a number of vests in the protection level you desire. When you narrow your choice to several vests, call NLECTC for the test data. In the end, it is your choice based on the factors that are most important to you. Q. What threat level of armor should I wear? A. First assess the type of threat you face on a daily basis. Review data from shooting incidents in your area, as well as the types of weapons being confiscated from suspects. Also factor in what type of sidearm you are carrying; Federal Bureau of Investigation (FBI) Uniform Crime Report (UCR) data indicate that approximately one in six officers killed in the line of duty were shot with their own weapon. Other considerations are: the climate in which you work, typical duty assignment, and personal preference considerations (comfort and fit). Again, the decision is ultimately yours. Q. Which manufacturer makes the best body armor? A. NLECTC tests body armor from many manufacturers to verify their products meet minimum performance standards necessary for police use. The test does not compare one manufacturer or their products with another. We recommend that you look at armor from a number of manufacturers. Inquire about their customer service/support, and talk with other agencies about the armor they have purchased and used. Our Consumer Product List gives a complete listing of manufacturers and models that comply with NIJ Standard You can also call NLECTC at or to get the most current information on models that comply with the standard. Side Panel Style s Available in NIJ Level IIA, II, and IIIA Ballistic/stab-shank armor upon request 6 x 8, 15.24cm x 20.32cm pocket size Choice of soft trauma plate, steel plate, or optional level III AK-47 plate Optional back plate pocket Available in male and female sizing Small (34-36) Medium (38-40) (42-44) X (46-48) XX (50-52) XXX (54-56) XXXX (58-60) Available in custom sizes Vests come in choice of short, regular, long lengths White, Black, Blue, Tan, Camouflage Full front, back and side protection 6 point elastic adjustment straps on shoulders and sides to ensure perfect fit Double adjustment straps on shoulder to properly suspend body armor for maximum comfort and to keep panels from sagging Water resistant Lightweight and discrete Excellent ventilation and heat dissipation 2 Call Toll Free: Call Toll Free:

3 Vests Tactical Vests Tactical Cross Draw Vest Modular Vest Protection level NIJ Level IIIA Interior pockets for use of level III or level IV hard armor plates 2.6 lb 1.2kg 10 x 12 front and back plate pockets Measurement 21 x 21 x cm x 53.34cm x 2.54cm One size fits most Pockets 9 Pouches 2 side utility pouches 2 rifle magazine pouches 2 small utility pouches on the chest 2 pistol magazine pouches 1 gun pouch Pouches come with Velcro and plastic fasten for security Adjustable shoulder straps Adjustable side straps so one size fits most Grip on shoulders for stably bracing weapons Inside pouches for additional storage Back pouch for hydration bladder MOLLE webbing on front and back for additional accessories Belt straps on bottom attach to any size belt Pistol pouch contained by quick-release elastic strap and plastic clasp s Small (34-36 )to XXXXL (58-60) Custom Sizing available Pouches Black All modular pouches are designed to exact specifications of the equipment being carried Full line of standard pockets and pouches can accommodate any special or custom request, modular grid system Practically limitless pocket and web configuration Balanced loads front and back Concealed front and back hard armor plate pockets Front zipper for rapid access or removal Side adjustments for proper fit Removable ballistic panels Removable rifle butt retention pad Front and back removable ID Attachment system for communication wiring Includes four pouches to fit modular grid system Optional Features NIJ Level III or IV 10 x12 hard armor plates Helmet friendly ballistic collar Ballistic groin and biceps protectors 1000 denier Cordura outer shell Carry bag Basic Tactical Vest MOLLE Interceptor Vest Available in NIJ Level II and IIIA Optional coverage Level III or IV hard armor plates NIJ Level IIIA Interior pockets for use of level III or level IV hard armor plates s Two sizes of Hard Armor plate pockets in front and back 8 x 10, 20.32cm x 25.4cm 10 x 12, 25.4cm x 30.48cm Available in variety of sizes from small to XXL in women s and men s sizes Special design for women s vest for improved contour and fit Available in custom sizes ranging between 3.8 and 6.6 pounds depending on size with use of ballistic panels Camouflage, Black, Navy Blue, Tan, OD Green, ACU Provides front, side, and back protection Internal pouches for ballistic panels External pouches for hard armor plates Velcro shoulder straps for easy donning and adjustability for comfort and fit Removable I.D. patches in front and back Available with or without ballistic collar protection s 10 x 12 front and back plate pockets small to Xtra Woodland and Desert MOLLE webbing on front and back for use of MOLLE gear Front and back hard armor plate pockets Back pocket for hydration bladder Adjustable side straps for secure fit Double Velcro front closure assures secure fit Removable ballistic panels Optional Features Ballistic collar protection Ballistic groin protection Ballistic biceps protection Side plate pockets 4 Call Toll Free: Call Toll Free:

4 Vests Tactical Vests Tactical MOLLE Vest s NIJ Level IIIA Interior pockets for use of level III or level IV hard armor plates 10 x 12 front and back plate pockets small to XXtra Black Adjustable shoulder straps with two-sided Velcro closure for extra security Internal Velcro waist fastener with elastic for snug fit Adjustable side-to-front closure with two-sided Velcro for secure, and snug fit Water resistant ballistic material Water resistant Nylon outershell Front and back pouches for 10 x 12 hard armor panel Front and back area for removable ID Webbing on front and back for use of MOLLE accessories Breast area has webbing with Velcro atop to allow for velcro fastening and MOLLE accessory use Optional Features Ballistic biceps protection Ballistic collar protection Removable exterior pockets Provides front, side, and back protection Internal pouches for ballistic panels External pouches for hard armor plates Velcro shoulder straps for easy donning and adjustability for comfort and fit Removable I.D. patches in front and back Basic Tactical Vest with Yoke Protection Protective Features s Available in NIJ Level II and IIIA Optional coverage Level III or IV hard armor plates Two sizes of Hard Armor plate pockets in front and back 8 x 10, 20.32cm x 25.4cm 10 x 12, 25.4cm x 30.48cm Removable Ballistic Yolk Protector Available in variety of sizes from small to XXL in women s and men s sizes Special design for women s vest for improved contour and fit Available in custom sizes ranging between 3.8 and 6.6 pounds depending on size with use of ballistic panels Camouflage, Black, Navy Blue, Tan, OD Green, ACU Narc Special NIJ Level IIIA Front interior and back exterior pockets for use of level III or level IV hard armor plates 8 x 10 front and back pockets 10 x 12 front and back pockets s Small (34-36) Medium (38-40) (42-44) X (46-48) XX (50-52) XXX (54-56) XXXX (58-60) Available in custom sizes Front zipper and two-sided Velcro closure Adjustable sides for secure fit 4 rapid access utility pockets in front Radio pocket on left side Flashlight pocket on back shoulder Front and back panels attach at shoulders Removable front and back ID Flex cuff compartment on either shoulder Optional Features NIJ level III or IV hard armor plates Ballistic groin protection Ballistic collar protection (helmet friendly) Rifle retention butt pad Concealed back hard armor plate pocket 1000 denier cordura outershell Carry bag MOLLE webbing on front and back for use of MOLLE gear Front and back hard armor plate pockets Back pocket for hydration bladder Adjustable side straps for secure fit Double Velcro front closure assures secure fit Removable ballistic panels MOLLE Vest with Collar and Biceps Protection Protective Features s NIJ Level IIIA Interior pockets for use of level III or level IV hard armor plates 10 x 12 front and back plate pockets Removable ballistic collar and biceps protection small to XXtra Woodland and Desert 6 Call Toll Free: Call Toll Free:

5 Plate Carriers Vests Specialized Organic Plate Carrier NIJ Level III Front and back 15 x 12 s Sides 6 x 6 5 x 8 One size Desert Tan, Coyote,Navy, Black, OD Green Organic Polyethylene Plates NIJ Level III State-of-the-art technologies Ultra-light rifle plate Vest dependent Front and back placement Complete front and back protection Resistant against water, sun, temperature change, acids and oils Adjustable Velcro shoulder straps Adjustable side Velcro closure Front and back pouches for 15 x 12 organic plates Side pockets for full side protection with 5 x 8 or 6 x 6 Polyethylene ballistic plates Magazine Carrier Vest Front and Back Pouches for use of 10 x12 Ballistic Plates Measurement Pockets Front Panel Length cm width cm Back Panel cm cm 6 pockets in front Each at 5.5 x 3 x 3.5 Or 13.97cm x 7.62cm x 8.89cm 2.8lbs 1.3kg Front Pocket cm cm Separate front and back pouches for ballistic plates MOLLE webbing system for added accessories and pouches Easy frontal accessibility to Velcro pouches Side snaps adjustable for snug fit Shoulder straps adjustable for snug fit Includes shoulder pads for lasting comfort Organic Polyethylene Plate 12 x cm x 38.1cm 4.8lb 2.2kg MOLLE Plate Carrier with Pockets Front and Back Pouches for use of 10 x12 Ballistic Plates Measurements Front 15 x 16 38cm x 40.64cm Back 15.5 x cm x 40.64cm 2.4lb 1.1kg MOLLE Webbing allowing for addition or removal of different MOLLE accessories including: Magazine pouches, storage pouches, cuff pouches, hydration pouch, ammo pouch, etc. Adjustable shoulder straps with quick release snaps and padding for comfort Adjustable waist straps with quick release snaps Contoured cut for easy movement Reporter Vest Protection level s Pockets Small to X- Available in custom sizes 3 secured zipper pockets on front 2 large 8 x 7 pouches with Velcro closures 3.5 x 3.5 stacked pockets with Velcro closures 5 x 4.5 chest pouch with Velcro closure 8 x 5.5 pouch with Velcro closure and pen/pencil holder 11 x 11 back pouch with triple Velcro closure Right and left hand pockets Right and left interior pockets with Velcro closure Discrete ballistic protection Full front, back and partial side protection Front ballistic flap with Velcro closure allows for full chest coverage Removable front and back ballistic panels Adjustable side straps for secure fit Interior side elastic straps for comfort, fit and maneuverability Front zipper for easy donning and removal 8 Call Toll Free: Call Toll Free:

6 Vests Specialized Anti-Riot Suit Coast Guard Vest Protection level s Small, Medium,, Extra 11.2lb 5.08kg Measurement 23 x 21 x cm x 53.34cm x 15.24cm Blue, Black, and Orange Total of four flotation pieces attached to vest 2 in the front 12 x 9.5 x at the nape 7 x 12 x on the back 15 x 13 x 2.25 Water resistant exterior Adjustable Velcro straps at shoulders and sides for secure fit Ballistic protection in front, back and sides Adjustable Velcro waist strap inside for secure fit 4 Front to back adjustable groin straps with clasps for secure fit 4 utility pockets on the front Additional ballistic groin protection flap that can be left up or put down Description Full body coverage Hard-shell exterior made from nylon 66 Soft interior for comfort Ergonomic design Jointed pieces for maximum maneuverability Adjustable straps for secure fit Components Chest protector Back protector Shoulder protector Abdomen and groin protector Thigh protector Leg and foot protector Biceps and forearm protector Tactical gloves Carry bag CANVAS Material Swatches Optional pieces Anti-riot helmet Ballistic shield Bordeaux Sandstone Camo Green 483 Coyote Flannel Desert Camo Woodland Digital Camo Multi Camouflage Green Camouflage NYLON Black Navy Blue Tactical Khaki Steel White 10 Call Toll Free: Call Toll Free:

7 Helmets Helmets PASGT Helmet Military Standard 662F Offset three point suspension system Interior shock absorption system Ergonomically fit Optimal ambient hearing Communication device friendly Ballistic collar friendly Adjustable headband Circumference Small Medium Extra Measurements: s Length Width Height Small Medium Extra Small Medium Extra 2.76lbs 1250g 2.87lbs 1300g 2.98lbs 1350g Available in black, tan, and sage green 3.36lbs 1525g Rapid Response Helmet Sm/Med Med/Lg Lg/XL 2.67 lbs 1211g 2.93 lbs 1328g 3.18 lbs 1445g Sizing Sm/Med Med/Lg Lg/XL Head 53cm 56cm /8 Head 56cm 59cm 22 1/8 23 3/8 59cm 61cm 23 3/8 24 Up to 7 Up to 7 3/8 Up to 7 5/8 Green, Tan, Black, Camouflage, ACU Model IA0034 Helmet Military Standard 662F Occ-dial at back allows for maximum secure fit Head-lock chinstrap system increases helmet stability Night vision mount Elastic band reduces vibration of night vision devices Compatible with most night vision devices 4 Position accessory rail connectors for use of helmet accessories MICH Helmet Military Standard 662F Compatible with night vision, communication, nuclear, biological, and chemical equipment Performs in temperatures -40 F to 160 F Fully adjustable strap-harness suspension for maximization of stability and comfort Improved interface with body armor, for full range of motion Helmet mount optional Circumference Small Medium Extra Measurements: s Length Width Height Small Medium Extra Small Medium Extra 2.95lbs 1340g 3.06lbs 1390g 3.17lbs 1440g 3.51lbs 1590g Full protection against non-ballistic threats 2.6 lbs 1.18 kg Black Anti-Riot Helmet Provides full head, neck, and face protection against non-ballistic threats Helmet and face-shield made of high impact resistant plastic Inside is padded to minimize shock of blunt trauma to head Face shield can flip-up Comes with neck protector Adjustable chin strap allows for perfect fit Available in black, tan, and sage green TC-2001 Helmet Military Standard 662F Compact size reduces risk of interference Convenient use as paratrooper helmet Lightweight and comfort enhances mobility Adjustable sizes between XXS to XL by adapting inside padding system Four-point adjustable chinstrap retention system Med Lg XL Compliance 3 lbs 1360g 3.25 lbs 1474g Black, Tan, Sage Green 3.4 lbs 1542g Compliant with use of all major gas masks worn under helmet Compliant with use of night-vision goggles Face Shield Level II Circumference Small Medium Extra Measurements: s Length Width Height Small Medium Extra Medium Extra 5.8lbs 2631g 6.0lbs 2721g Available in black, tan, and sage green 6.4lbs 2903g PASGT Helmet w/face Shield Military Standard 662F Offset three point suspension system Interior shock absorption system Ergonomically fit Optimal ambient hearing Communication device friendly Ballistic collar friendly Adjustable headband Full coverage of face Flip-up Face shield with level II ballistic protection 12 Call Toll Free: Call Toll Free:

8 Accessories Backpacks Ballistic Face Mask Half Measurements: NIJ Level IIIA Half Length cm Width cm Full cm cm Back Pack Panel NIJ Level IIIA 0.2lb Dimensions x 12.5 Ballistic Face Mask Full cm Half Full cm 1.2lbs 0.5kg 1.4lbs 0.7kg Ergonomic fit Designed to maximize comfort while providing total facial protection Additional padding incorporated at forehead and sides to minimize shock from ballistic threats Six-point elastic system allows user to adjust for perfect fit Full face mask for use without use of helmet To stop 44 magnum Half face mask compatible with ballistic helmets for maximum protection Available in custom sizes Available in executive briefcase panel Built-in pocket for ballistic protection back pack panel level IIIA Adjustable shoulder straps and waist belt for comfort and easier carry 5 main compartments with additional storage inside Ideal for easy organization and accessibility MOLLE webbing on exterior for attachment of extra accessories Optional back pack panel insert for ballistic protection Lightweight Full coverage of back Multi-hit, to stop 44 magnum Available to fit executive briefcase Available in custom sizing Back Pack Measurements: Length cm Width cm Height cm 5.8lbs 2.63kg Pockets Pocket L x W x H Main 21 x 20 x 7.5 External 13 x 11 x 3.5 Lower 6 x 12.5 x 3.5 Side 9 x 5 x 2 Laptop Bag Measurement 15 x 12 x 4 2.4lbs 1.1kg Ballistic Chaps Protection level s Standard size: Length = 31 (78.74cm) Width at thigh = 20 (50.8cm) Width at calf = 17 (43.18cm) Available in custom sizes Brown, Navy, Black, Tan, Forest Camo, Camo Can be sewn into denim pants Full front and partial side protection Removable ballistic panel Adjustable Velcro belt loop with quick-release plastic snap - to keep chaps in place 3 adjustable elastic straps with Velcro at thigh, knee and calf to ensure a secure fit and comfort Cutout at bottom to fit over footwear Can be made to fit denim pants for discrete ballistic protection Protection from: Two DM-51 hand grenades One 1lb. pipe bomb.22 Cal 17 gn FS pave V50: 1568 ft/s and 1573 ft/s MOLLE webbing on exterior for extra attachments Three main pouches with extra pockets and compartments inside. Drop system made to allow laptop to open while laptop carrier is carried. Pouch to insert ballistic protection briefcase panel level IIIA 14 Call Toll Free: Call Toll Free:

9 Hard Armor Plates Ceramic In-Conjunction NIJ Level IV with IIIA Vest Able to defeat level IV threats when used with level IIIA vest Single curve Defeats 7.62mm NATO 148gr. (.308) FMJ at 2780 fps and lesser threats when used with IIIA vest State-of-the-art technologies Ultra-light rifle plate Vest dependent Resistant against water, sun, temperature change, acids and oils Polyethylene In-Conjunction NIJ Level III with IIIA Vest 5 x 8 Ceramic In-Conjunction 5 x cm x 20.32cm 6 x 8 Ceramic In-Conjunction 6 x cm x 20.32cm 8 x 10 Ceramic In-Conjunction 8 x cm x 25.4cm 10 x 12 Ceramic In-Conjunction 5 x 8 Polyethylene Plate In-Conjunction 5 x cm x 20.32cm 6 x 6 Polyethylene Plate In-Conjunction 6 x cm x 15.24cm 6 x 8 Polyethylene Plate In-Conjunction 6 x cm x 20.32cm 8 x 10 Polyethylene Plate In-Conjunction 8 x cm x 25.4cm 10 x 12 Polyethylene Plate In-Conjunction 10 x cm x 30.48cm 25mm 18mm 15mm 15mm 16mm 16mm 16mm 22mm 25mm 3.2lb 1.5kg 3.2lb 1.5kg 5.0lb 2.3kg 7.4lb 3.4kg 0.8lb 0.36kg 0.6lb 0.27kg 1.0lb 0.45kg 2.2lb 1.0kg 2.6lb 1.18kg Ceramic Stand Alone NIJ Level IV Stand Alone Able to defeat level IV threats without support from tactical vest Single curve Front and back placement Defeats 7.62mm NATO 148gr. (.308) FMJ at 2780 fps and lesser threats without additional ballistic support Polyethylene Stand Alone NIJ Level III Stand Alone State-of-the-art technologies Ultra-light rifle plate Defeats level 3 threats without additional ballistic support Front and back placement Resistant against water, sun, temperature change, acids and oils 10 x 12 Ceramic Stand Alone 10 x 12 Ceramic Stand Alone Lightweight Organic Polyethylene Plate Polyethylene Stand Alone Single Curve Polyethylene Stand Alone Triple Curve 12 x cm x 38.1cm 21mm 20mm 20mm 30mm 30mm 8.6lb 3.6kg 6.6lb 3.0kg 4.8lb 2.2kg 3.4lb 1.5kg 3.4lb 1.5kg 16 Call Toll Free: Call Toll Free:

10 Hard Armor Plates Titanium/Steel NIJ Level III with IIIA Vest Front and back placement 30% lighter than other steel armor plates Capable of stopping multiple hits from 7.62mm x 51mm (.308 caliber) FMJ and lesser threat as AK-47/ Kalashnikov 7.62mm x 39mm Ballistic Shield NIJ Level IIIA NIJ Level III Available 4.5 x 16 Ballistic glass cut out for visibility Padded handles for comfortable use and handling Retention straps Optional protective case 5 x 8 Titanium/Steel Plate 6 x 6 Titanium/Steel Plate 6 x 8 Titanium/Steel Plate 8 x 10 Titanium/Steel Plate Ballistic Shield Level llla Ballistic Shield Level lll 5 x cm x 20.32cm 6 x cm x 15.24cm 6 x cm x 20.32cm 8 x cm x 25.4cm 40 x x 23 7mm 10mm 5mm 7mm cm cm 2.8lb 1.3kg 2.2lb 1.0kg 2.6lb 1.2kg 3.8lb 1.7kg 20lb 50lb 22.68kg Titanium/Steel NIJ Level III with IIIA Vest AK x 12 Steel Plate 7mm 5.6lb 2.4kg 10 x12 Titanium/Steel Plate 10mm 7.6lb 3.4kg Trauma Plate Concealable For use with concealable vests Allows for protection without conspicuous appearance Front and back plates Lightweight Trauma Plate Concealable 6 x cm x 20.32cm 4mm 0.4lb 0.2kg The International Armor Story With over 20 years experience, International Armor Corporation is proud to serve in an industry that is significant to our law enforcement and military community. By leveraging experience with vision, we have strived and succeeded in providing our clients with body armor protection unparalleled in quality, customization, and innovation. As a premier leader in the body armor industry, our research team carefully selects and designs proven and approved technology and material to meet all your protection needs. Our analysis team collaborates with you to make smart customization decisions. And whether you are interested in learning more about our products, contacting our staff, or simply have questions regarding our website, our service team can help you get the answers you need. Full support from beginning to end, our highly skilled industry professionals work in unison towards one clear goal: your security. Our body armor is certified to be in full compliance with the National Institute of Justice (NIJ) /04 standards All ballistic panels manufactured by International Armor Corporation are covered by a 5 year warranty from date of purchase All nylon covers carry a 3-year warranty from date of purchase All removable poly-cotton carriers carry a 18 month warranty from date of purchase By accepting any of International Armors products, the purchaser accepts all and full responsibility for all aspects of the product and its use including but limited to fit, style, size, body coverage, threat level, ballistic properties, and configuration. 18 Call Toll Free: Call Toll Free:

11 CONTACT INTERNATIONAL ARMOR International Armor Corp. Administrative Offices and Manufacturing Headquarters 1315 Calle Avanzado San Clemente, Ca Phone: (949) Fax: (949) International Armor Corporation Toll Free in U.S.: Local / International: (9:00am 5:00pm PST) Fax: Customer Service and Product Information Office 2913 El Camino Real #401 Tustin, CA Phone: (714) help@internationalbodyarmor.com Order Information: sales@internationalbodyarmor.com International Service and Product Information: intl@internationalbodyarmor.com For K-9 One Vest sales or inquiries, please contact our K-9 Specialist: 1315 Calle Avanzado San Clemente, Ca K9@internationalbodyarmor.com