SIGN LOCATION AND VISIBILITY AT INTERSECTIONS

Transcription

1 Kerb Line Concrete bullnose B A B Median Kerb Concrete bullnose where required Single 300mm limit line Kerb Line A m ± 1.0 m Tolerance to accommodate site pedestrian cutdowns SIGNS A RG 5,6 B RG 17, PW 5, 19 SIGN LOCATION AND VISIBILITY AT INTERSECTIONS D3.7.1

2 NOTES: Triangular arrows to be added to Street Name signs as indicated on diagrams (both sides of sign). STREET NAME SIGNS ARTERIAL / COLLECTOR INTERSECTION D3.7.2

3 (A) Local Road (B) (A) (C) Local Road (C) (A) NOTES: 1. Triangular arrows to be added to Street Name signs as indicated on diagrams (both side of signs) STREET NAME SIGNS ARTERIAL OR COLLECTOR D3.7.3 INTERSECTION WITH LOCAL ROAD

4 (A) (A) (B) NOTES: 1. Triangular arrows to be added to Street Name signs as indicated on diagrams (both side of signs) STREET NAME SIGNS LOCAL / LOCAL INTERSECTIONS D3.7.4

5 Local Road Collector or Arterial Road Kerbline RG26 BEGINS ENDS Boundary Refer D3.9.2 for setout and marking ENDS shared path BEGINS RG26 Kerbline Kerbline RG26 BEGINS ENDS shared path CYCLE SIGNAGE FOR OFF ROAD CYCLE PATHS D3.7.5

6 Alleyway leading to major road or nearby school One sign at beginning of cul-de-sac only (unless cul-de-sac has an alleyway then one to go in alleyway). Cul-de-sac 500m max. Roads NOTE: (eg street light columns, power poles or signs) where possible using approved NEIGHBOURHOOD WATCH SIGNAGE D3.7.6

7 5mm 5mm 10mm 10mm Socket for 10mm tapered Socket for 10mm tapered aluminium pin aluminium pin NB 65 poles. Top to be no more than 50mm above Concrete 20 MPa NB50 + NB65 poles. Top of socket to be surface: i.e. Concrete, Cobbles or Asphalt Concrete 20 MPa This detail only to be used for Real Time Bus signage or at request of Councils Engineer. GROUND SOCKETS FOR REMOVABLE POLES D3.7.9

8 Sign blade NB 50 Galtube Plus pole See Note Ground Level Refer to D3.7.9 for Ground Socket details dia Min. NOTES: 1. to allow reinstatement of the surrounding surface up to the face of the pole. 2. Steel tube shall be:- Cast in-situ in 300 Dia concrete surround. INSTALLATION OF CHEVRON OR ROUTE AND LOW LEVEL ROAD NAME SIGN D3.7.10

9 2 / 6 Ø Tek Screws Street Sign Mount 2 / M6 Set Bolts M12 Bolt NB 56 Pole NB 56 Pole See Note 4 2/6 Ø Tek Screws Street Name Sign Blade Pole Cap 6 Ø Tek Screw Pole Cap M12 Bolt M6 Set Bolt sign blade Street Sign Mount M6 Set Bolt 3.7m Of NB 56 white powder coated Galtube Plus Pole 6 Ø Tek Screw M12 Bolt NOTES: The distance between the ground and the top of the top sign blade shall be 3.0m Cut notch into I ATTACHMENT OF STREET NAME SIGN BLADES TO POLES D3.7.11

10 Galloway St VARIES Galloway St VARIES Naylor St VARIES STREET NAME PLATE D3.7.12

11 OD Aluminium tube 25 x 25 Aluminium R.H.S. 4 Ø bolt with self locking nut. 8 Supply with 1360 x 125 drawstring bag Bag from Oxford Nylon Floro/Orange 210 x 210 Denier-Polyurethene coated 800mm water proofness (Nylox 88) Flag printed with 'Children' sign 975 FLAG FRAME Flag frame Fold over and sew at 42mm to Aluminium tube Opening this end Flag Pole Double fold edges 10mm and sew x 130 Back corner square. (Double thickness). Sew across diagonal and form Flat. FLAG MATERIALS: Flag:- Oxford Nylon PU/PVC backing 420 x 420 Denier, Colour Rescue Orange Back Corner square:- Textured Polyester Denier 700 FLAG NOTE: KEA CROSSING FLAG D3.7.13

12 Weld all round Weld all round Refer Detail A x 38.1 x 1.6 RHS Tack weld inside 50 NB pipe x 38.1 R.H.S. DETAIL A 50 NB Med. tube. Galvanised and white Refer to D3.7.9 for Ground Socket details Set in concrete 20MPa Ø bar 130 long weld all round to pipe 50 KEA CROSSING FLAG POLE D REGIONAL INFRASTRUCTURE TECHNICAL SPECIFICATION Version: AUGUST 2016

13 mm OD Tube mm OD Cap/Collar welded on 38mm OD Sleeve MALE BRACKET Sleeve welded to the 35mm Ø tube Not less than 1.5m in length Wooden support pole Type II bollard 35mm OD Male Bracket 35mm ID Female pole RG-28 sign 300mm Min. Female Bracket Height varies depending INSTALLATION OF FEMALE BRACKET ONTO POST 600mm preferred Ground 10mm Ø 47mm OD Nylon Bush 40mm ID Ø10mm Bolt 35mm ID Female pole RG-28 sign 300mm min. 600mm preferred NOTE: FEMALE BRACKET All components are to be galvanised steel SCHOOL PATROL SIGNS D3.7.15

14 Bus Stop Taxi NOTES: 1. Sign to be double sided. 2. Sign to be mounted to the back of a bus stop / taxi pole. 3. Sign 200x Symbol to suit sign. 5. BUS STOP / TAXI SUPPLEMENT D REGIONAL INFRASTRUCTURE TECHNICAL SPECIFICATION Version: AUGUST 2016

15 600 arrow and 20mm border NOTE: THROUGH TRUCK ROUTE MARKER D3.7.17

16 Sign as 50 Ø hole thru 150 RHS on of 125 RHS 125 x 125 x 6 RHS (Max) 150 x 150 x 6 RHS high x 75 x 12 MS plate gussets Ø PVC Conduit NOTE: Every overhead or gantry to be individually designed for purpose ELEVATION OVERHEAD DIRECTIONAL SIGN STANDARD D3.7.18