THE NETHERLANDS (N E D E R L A N D) EC TYPE-APPROVAL CERTIFICATE

Transcription

1

2 Vehicle Technology Division THE NETHERLANDS (N E D E R L A N D) EC TYPE-APPROVAL CERTIFICATE Communication concerning: - type-approval (1) - extension of type-approval (1) - refusal of type-approval (1) - withdrawal of type-approval (1) of a type of vehicle with regard to Directive 2002/24/EC as last amended by Directive 2005/30/EC. EC type-approval number Reason for extension Approval mark : e4*2002/24*1151*00 : Not applicable : e4*2002/24* General 0.1. Make(s) (trade name of the manufacturer) : Access 0.2. Type : SP250 Variant(s) : Not applicable Version(s) : SP250-S Commercial name(s) : Access Motor, as option: SS250R, Hammel, Quadzilla, Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike 0.3. Means of identification of type, if marked on the vehicle :???SP???????????? Location of that marking : On the right side of frame body 0.4. Category (2) :L7e 0.5. Name and address of the vehicle manufacturer : Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. P.O. Box 777 Tel (0) Vehicle Approval and Information 2700 AT Zoetermeer Fax + 31 (0) The Netherlands WVTA v2.00 Page 1 of 4

3 Type-approval number: e4*2002/24*1151* Name(s) and address(es) of assembly plant(s) : Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. The undersigned hereby certifies the accuracy of the manufacturer s description in the attached information document of the vehicle type described above, for which one or several representative samples, selected by the competent approval authorities, has (have) been submitted as prototype(s) of the vehicle type and that the attached test results are applicable to the vehicle type. The vehicle type meets/does not meet (1) the technical requirements of all relevant separate Directives (as last amended) listed in the table of Annex I to Directive 2002/24/EC. The approval is granted/refused/withdrawn (1). Place : Zoetermeer Signature : Date : Attachments: Information document, Parts 1 and 2 (Annex II). Test results (Annex VII). Name(s) and specimen(s) of the signature of the persons authorised to sign the certificates of conformity and a statement of their position in the company. A model certificate of conformity. (1) Delete where not applicable. (2) According to the classification introduced in Article 1. WVTA v2.00 Page 2 of 4

4 Type-approval number: e4*2002/24*1151*00 ANNEX VII TEST RESULTS (Article 5(1), first subparagraph) In each case, the information must make clear to which variant and version it is applicable. One version may not have more than one result. 1. Results of the sound level tests. Number of the base Directive and latest amending Directive applicable to the approval. In the case of a Directive with two or more implementation stages, indicate also the implementation stage: - 97/24/EC Chapter 9 as last amended by 2005/30/EC Variant/version -- / SP250-S Moving db(a) Stationary db(a) at (min -1 ) Results of the exhaust emission tests. Number of the base Directive and latest amending Directive applicable to the approval. In the case of a Directive with two or more implementation stages, indicate also the implementation stage: - 97/24/EC Chapter 5 as last amended by 2005/30/EC, stage 2003 Variant/version -- / S Type I CO (g/km) HC (g/km) (1) NO x (g/km) (1) HC + NO x (g/km) (2) Type II CO (g/min) (2) HC (g/min) (2) CO (% vol) at normal idle speed (1) Specify the idle speed (1) (3) 1500± CO (% vol) at high idle speed (1) Specify the idle speed 2100±100 (1) (3) Engine oil temperature (1) (4) 64 C at 1540 min C at 2190 min WVTA v2.00 Page 3 of 4

5 Type-approval number: e4*2002/24*1151*00 3. Compression ignition engine Variant/version Corrected value of absorption coefficient (m -1 ) (1) Only for motorcycles and motor tricycles and for quadricycles as defined in Article 1, paragraph 3(b). (2) Only for mopeds and for light quadricycles as defined in Article 1, paragraph 3(a). (3) Mention the measurement tolerance. (4) Applicable for four-stroke engines only. WVTA v2.00 Page 4 of 4

6 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: CERTIFICATE OF CONFORMITY CERTIFICATE OF CONFORMITY ACCOMPANYING EACH VEHICLE IN THE SERIES OF THE TYPE WHICH HAS BEEN APPROVED The undersigned: hereby certifies that the following vehicle: 0.1. Make: Access 0.2. Type: SP250 Variant: N.A. Version: SP250-S Commercial name(s): Access Motor, as option: SS250R, Hammel, Quadzilla, Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike 0.4. Vehicle category: L7e Vehicle category according to Directive 97/24/EC, Chapter 7: N.A Name and address of the manufacturer: Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C Location of the statutory plate: R, x1147, y126, z660 Vehicle identification number: RK3SP03105A Location of the vehicle identification number on the chassis: R, x100, y87, z455 Conforms in all respects to the type described in EC type-approval - EC type-approval number: e4*2002/24*1151*00 - Dated: The vehicle can be permanently registered without requiring any further approvals, for driving on the right/left and for using metric/imperial units for the speedometer. Chia-Yi, Taiwan, R.O.C. (Place) (Date) (Signature) (Position)

7 Additional Information 1. Number of axles: 2 and wheels: 4 3. Wheel base: 1270 mm 6.1. Length: 1825 mm 7.1. Width: 1230 mm 8. Height: 1140 mm Mass of the vehicle (with bodywork) in running order: 221 kg Unladen mass of the vehicle: 211 kg Technically permissible maximum laden mass: 371 kg Distribution of this mass among the axles: kg kg Technically permissible mass on each axle: kg kg 17. Maximum mass of trailer: N.A. (brake):.kg (unbraked): kg Maximum vertical load at the coupling point for a trailer: N.A. 20. Engine manufacturer: Access Motor Co., Ltd. 21. Engine type as marked on the engine: E Engine number: E10R Working principle: electric/spark ignition/compression ignition, four/two stroke 23. Number and arrangement of cylinders: One, vertical 24. Cylinder capacity: cm Fuel: P 26. Maximum net power or maximum continuous rated power as applicable: 12.9 kw at 7000 min Ratio: maximum net power or maximum continuous rated power/mass of the vehicle in running order: kw/kg 28. Gearbox (type): A(automatic) 29. Gear ratio: CVT GEARBOX CHAIN Minimum Maximum FORWARD REVERSE RATIO 1 st gear D gear 1: : : : : : Tyre size designation: Axle 1: Axle 2: or

8 37. Body: No 41. Number and configuration of doors: N.A Number and position of seats: 2, r1: 1C, r2: 1C Approval mark of coupling device, if fitted: N.A. 44. Maximum speed: 85 km/h 45. Sound level: In accordance with 97/24/EC Chapter 9, amendment 2005/30/EC Stationary: 82 db(a) at engine speed: 3500 min -1 Drive-by: 79 db(a) 46. Exhaust emissions: In accordance with 97/24/EC Chapter 5, amendment 2005/30/EC, stage 2003 Type I test: CO: g/km, HC: g/km, NOx: g/km, HC+NOx: -- Type II test: for motorcycles and tricycles: CO: % Visible air pollution caused by an engine with compression ignition: N.A. - corrected value of absorption coefficient: N.A. 47. Fiscal power or national code number(s): Italy: France: Spain: Belgium: Germany: Luxembourg: Denmark: Netherlands: Greece: United Kingdom: Irland: Portugal: Austria: Sweden: Finland: Czech Republic: Estonia: Cyprus: Latvia: Lithuania: Hungary: Malta: Poland: Slovenia: Slovakia: 50. Remarks: 51. Exemptions:

9

10 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 TEST REPORT according to Council Directive on the approximation of the laws of the Member States relating to the Type-approval of two or three-wheel motor vehicles No.: 2002/24/EC including all amendments until No.: 2005/30/EC Previously granted EC-system type approval : -- Structure of report : 0. General information 1. Test object(s) and general test information 2. Test minutes 3. Remark concerning tested object(s) 4. Appendices 5. Statement of conformity TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 1 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

11 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP General information 0.1. Trademark or trade name of the vehicle 0.2. Manufacturer s name for the type of the vehicle 0.3. Name and address of the manufacturer 0.4. Name and address of the manufacturer s authorized representative 0.5. No. of information document date of issue date of last amendment : Access : SP250 : Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. : Not applicable : : : SP /24-00 May 10, TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 2 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

12 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Test object(s) and general test information 1.1. Test object(s) Identification no. : RK3SP03105A000004, Engine No. *E10R000010* Variant(s) Version(s) Sort / category : Not applicable : SP250-S : Quadricycles / L7e 1.2. General test information Order issued by (if different from manufacturer) : Test object received on : Test date : March 28 to May 5, Test site : Tai-Bao, Sha-Lu, Lung-Tan and Chutung / Taiwan Remark : The results of the test refer exclusively to the object(s) mentioned under point 1.1. of this report. TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 3 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

13 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Test minutes 2.1. Test facilities : The test facilities used are in compliance with the requirements of the directive Test results : The vehicle type has been tested according to the amendments mentioned in appendix 0. See Appendix Variants and components Variant(s) Version(s) : Not applicable : SP250-S 3. Remarks concerning tested object(s) All versions of the vehicle type as stated in the information document are covered with the tested vehicle version(s) and test object(s) respectively. TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 4 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

14

15 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 List of modifications Appendix 0 Correction of : -- Modification of : -- Addition of : -- Deletion of : -- TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 6 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

16 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Test minutes of the frame directive Appendix 1 1. General 1.1. Make : Access 1.2. Type : SP250 Variant(s) Version(s) : Not applicable : SP250-S 1.3. Name and address of manufacturer : Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C Name and address of manufacturer s authorized representative : Not applicable 2. General arrangement of vehicle 2.1. Category of vehicle : L7e 2.2. Maximum design speed : 85 km/h according to SD 95/1/EC, amendment 2002/41/EC Conformity checks Approval number : Requirements fulfilled : Not applicable 2.3. Wheels Number : Symmetrical or asymmetrical configuration : Not applicable 2.4. Frame layout diagram : See drawing No A03-H00 TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 7 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

17 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Masses and dimensions : According to SD 93/93/EEC, amendment 2004/86/EC Conformity checks Approval number : Requirements fulfilled : Not applicable 3.1. Mass of vehicle in running order : See Information Document SP /24-00, Distribution of that mass between the axles 3.2. Mass of vehicle in running order together with rider Distribution of that mass between the axles 3.3. Maximum technically permissible mass declared by the manufacturer Division of that mass between the axles Maximum technically permissible mass on the axles : See Information Document SP /24-00, : See Information Document SP /24-00, 2.2. : See Information Document SP /24-00, : See Information Document SP /24-00, 2.3. : See Information Document SP /24-00, : See Information Document SP /24-00, Vehicle length : 1825 mm 3.5. Vehicle width : 1230 mm 3.6. Vehicle height : 1140 mm TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 8 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

18 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Engine 4.1. Manufacturer of engine : See Information Document SP /24-00, Make : See Information Document SP /24-00, Type : E Spark- or compression-ignition engine : Spark-ignition / compression ignition engine Operating cycle : See Information Document SP /24-00, Cooling system : See Information Document SP /24-00, Lubrication system : Injection into induction system Number, arrangement and firing order of cylinders : See Information Document SP /24-00, Bore, stroke and cylinder capacity : See Information Document SP /24-00, Full drawing of induction system : See Information Document SP /24-00, Compression ratio : See Information Document SP /24-00, Maximum net power and maximum net torque Conformity checks Approval number : See Information Document SP /24-00, , according to SD 95/1/EC, amendment 2002/41/EC : Requirements fulfilled, for test results see appendix 3 : Not applicable Fuel tank : According to SD 97/24/EC Chapter 6, amendment 2005/30/EC See Information Document SP /24-00, TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 9 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

19 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Conformity checks Approval number (installation) Approval number (component) : Requirements fulfilled : Not applicable : See Information Document SP /24-00, Fuel supply : See Information Document SP /24-00, Anti-tampering measures for mopeds and motorcycles Conformity checks Approval number : Not applicable : Not applicable : Not applicable Electrical system : See Information Document SP /24-00, Generator : See Information Document SP /24-00, Electromagnetic compatibility : According to SD 97/24/EC Chapter 8, amendment 2005/30/EC see Information Document SP /24-00, Conformity checks Approval number : Requirements fulfilled : Not applicable Sound level and exhaust system : According to SD 97/24/EC Chapter 9, amendment 2005/30/EC Conformity checks Approval number : Requirements fulfilled, for test results see appendix 6 : Not applicable Make of exhaust system : See Information Document SP /24-00, Type of exhaust system : One main muffler TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 10 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

20 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Sound level Stationary noise, db(a) at min -1 : 82 / 3500 Noise when in motion in db(a) : Anti-pollution devices : According to SD 97/24/EC Chapter 5, amendment 2005/30/EC Conformity checks Approval number : Requirements fulfilled, for test results see appendix 4 : Not applicable 4.5. Electric traction motor : Not applicable 5. Transmission Type : Manual / automatic 2.2. Maximum design speed : According to SD 95/1/EC, amendment 2002/41/EC see Information Document SP /24-00, 4.6. Conformity checks Approval number : Requirements fulfilled : Not applicable Speedometer : According to SD 2000/7/EC, see Information Document SP /24-00, Tyres : According to SD 97/24/EC Chapter 1, amendment 2005/30/EC see Information Document SP /24-00, 5.2. Conformity checks Approval number : Requirements fulfilled : Not applicable Tyres of any tyre manufacturer may be fitted provided that they are of the same dimensions, E/emark approved according to ECE-R75 or 97/24/EC, chapter 1 and of a load index of 19 (front tyre) / 32 (rear tyre) or more and a speed index of G (all tyres) or more. TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 11 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

21 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Braking system : According to SD 93/14/EEC, see Information Document SP /24-00, 7. Conformity checks Approval number 8. Installation of lighting and lightsignalling devices Conformity checks Approval number : Requirements fulfilled, for test results see appendix 2 : Not applicable : According to SD 93/92/EEC, amendment 2000/73/EC See Information Document SP /24-00, 8.2. : Requirements fulfilled : Not applicable 9. Lighting and light-signalling devices : According to SD 97/24/EC Chapter 2, amendment 2005/30/EC see Information Document SP /24-00, 8.1. Conformity checks : Requirements fulfilled Approval number : See Information Document SP /24-00, Miscellaneous Coupling devices and their attachment : Not applicable Identification of controls, tell-tales and indicators : According to SD 93/29/EEC, amendment 2000/74/EC see Information Document SP /24-00, 9.2. Conformity checks Approval number : Requirements fulfilled : Not applicable Statutory inscriptions : According to SD 93/34/EEC, amendment 1999/25/EC see Information Document SP /24-00, 9.3. Conformity checks Approval number : Requirements fulfilled : Not applicable TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 12 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

22 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Location of statutory plate : At the front side of the front frame under radiator Devices to prevent unauthorised use : According to SD 93/33/EEC, amendment 1999/23/EC See Information Document SP /24-00, 9.4. Conformity checks Approval number : Requirements fulfilled : Not applicable Audible warning device : According to SD 93/30/EEC, see Information Document SP /24-00, 9.5. Conformity checks Approval number, annex II (installation) Approval number, annex I (component) : Requirements fulfilled : Not applicable : See Information Document SP /24-00, Location of rear registration plate : According to SD 93/94/EEC, amendment 1999/26/EC See Information Document SP /24-00, 9.6. Conformity checks Approval number : Requirements fulfilled : Not applicable External projections : According to SD 97/24/EC Chapter 3, amendment 2005/30/EC Conformity checks Approval number : Requirements fulfilled : Not applicable B. Information relating solely to two-wheel mopeds and motorcycles Not applicable C. Information relating solely to three-wheel mopeds, motor tricycles and quadricycles TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 13 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

23 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Windows : Without (vehicle without bodywork) Rear-view mirrors : According to SD 97/24/EC Chapter 4, amendment 2005/30/EC See Information Document SP /24-00, C 2.6. Conformity checks Approval number (installation) Approval number (component) : Requirements fulfilled : Not applicable : See Information Document SP /24-00, C Anchorages for safety belts : Without (vehicle without bodywork) TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 14 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

24 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Test minutes of braking system Appendix 2 0. Test condition 0.1. Test date : April 26, Test site : Tai-Bao / Taiwan 1. Test facilities : The test equipment used was in compliance with the requirements of the directive. 2. Test object(s) 2.1. Type : SP250 Variant : -- Version : SP250-S 2.2. Technically permissible mass on axles Axle 1 [kg] Axle 2 [kg] : 152 kg : 219 kg 2.3. Load conditions of the vehicle during the test Unladen Laden Axle 1 [kg] Axle 2 [kg] Total [kg] Number and arrangement of the axles : 2 axles TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 15 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

25 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Brief description of the service braking device Combined (service brake) Front (secondary brake) Manufacturer of the brake system Manufacturer of brake pad Rear (secondary brake) Manufacturer of the brake system Manufacturer of brake pad : Foot lever, manually operated, mechanical and hydraulic transfer, disc brakes : Hand lever, manually operated, mechanical and hydraulic transfer, two disc brakes : Access Motor Co., Ltd. : Horng Fuu Industrial Co., Ltd. : Hand lever, manually operated, mechanical and hydraulic transfer, single disc brake : Access Motor Co., Ltd. : Horng Fuu Industrial Co., Ltd Other devices (anti-lock, etc.) : Parking brake device: Independent hand lever, purely mechanical device acting on the rear axle TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 16 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

26 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Test results 3.1. Type-0 test, with engine disconnected / automatic transmission under normal driving condition Test speed Measured performance Measured force applied to control (km/h) (m/s 2 ) (N) Unladen, dry brakes Combined service brake Secondary brake axle Secondary brake axle Laden, dry brakes Combined service brake Secondary brake axle Secondary brake axle TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 17 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

27 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Reference tests for wet brake : Not applicable Test speed Measured performance Measured force applied to control (km/h) (m/s 2 ) (N) Unladen, dry brakes Service brake axle 1 between 0.5 and 1s / max Service brake axle 2 between 0.5 and 1s / max Laden, dry brakes Service brake axle 1 between 0.5 and 1s / max Service brake axle 2 between 0.5 and 1s / max Tests for wet brake : Test speed Measured performance Measured force applied to control (km/h) (m/s 2 ) (N) Unladen, wet brakes Service brake axle 1 between 0.5 and 1s / max Service brake axle 2 between 0.5 and 1s / max laden, wet brakes Service brake axle 1 between 0.5 and 1s / max Service brake axle 2 between 0.5 and 1s / max TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 18 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

28 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Type-0 test, engine connected : Not applicable Unladen, dry brakes Test speed Measured performance Measured force applied to the controls (km/h) (m/s 2 ) (N) Combined braking device applied 30% V max < % V max. (additional test) 80% V max. (max. 160 km/h) < < 500 TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 19 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

29 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Type-1 test, (fade test) : Not applicable Distance between the initiation of two consecutive stops : 1000 m Number of braking : 10 Laden, dry brakes Test speed Measured performance Measured force applied to control (km/h) (m/s 2 ) (N) Combined service brake Type 1 test, with engine connected / automatic transmission under normal driving condition : Not applicable Measured Measured force Test speed performance applied to control Laden, dry brakes Reference test Combined service brake (km/h) (m/s 2 ) (N) Combined service brake Parking brake test (if applicable) : The parking brake device is capable of holding the laden vehicle stationary on an 18% up or down gradient. TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 20 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

30 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Test minutes of max. engine power and torque Appendix 3 0. Test condition 0.1. Test date : April 26, Test site : Tai-Pao / Taiwan 1. Test facilities : The test equipment used was in compliance with the requirements of the directive. 2. Test vehicle(s) 2.1. Type : SP250 Variant : -- Version : SP250-S 2.2. Engine type / number : E10 / without, prototype 3. Engine performance 3.1. Test conditions Pressures measured at maximum power Barometric : kpa Water vapour pressure : 3.96 kpa Exhaust (to be measured when the original induction systems are not used) Inlet depression at engine intake system (to be measured when the original induction systems are not used) : -- : -- TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 21 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

31 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Temperatures measured at maximum power of the engine Intake air : 312 K Outlet of the inlet inter- cooler : -- Cooling liquid Engine cooling liquid outlet : 346 K Reference point in case of air cooling : -- Oil in the oil sump : -- Fuel Injector intake : -- Fuel-consumption measuring device Exhaust gas, measured at the point adjacent to the outlet flange(s) of the exhaust manifolds : 308 K : 1079 K Characteristics of the dynamometer Make Type : ARCOM s.r.l. : FR Fuel For positive ignition engines operating on liquid fuel Make Specification : China Petroleum Corp. : Reference fuel according to Annex IV of 97/24/EC Chapter 5 amended by 2005/30/EC Anti-knock additive (lead, etc.) Type : Not applicable TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 22 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

32 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Content mg/litre Test Report No.: / /06 Access Motor Co., Ltd. SP250 : Not applicable Octane number RON No. : 95.4 MON No. : 85.1 Relative density at 15 C at 4 C Calorific value : : : Not applicable Lubricant Make Specifications : China Petroleum Corp. : API SF/CD SAE viscosity grade : 10W/ Correction factor for mechanical efficiency of the transmission Overall factor (n1*n2*n3*n4) : 1 * Gear wheel Chain Belt (n1) : n.a. (n2) : n.a. (n3) : n.a. Hydraulic coupling or converter (n4) : n.a. TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 23 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

33 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Detailed results of measurement engine speed min rotation speed of dynamometer brake min dynamometer brake load N torque measured at crankshaft Nm power measured kw barometric pressure kpa inlet air temperature K water vapour pressure kpa atmosph. Correction factor mechanical correction factor corrected net torque at crankshaft Nm corrected power kw measured fuel flow (not corrected) g/kw h Engine temperature at the spark plug washer / engine coolant outlet K lubricating oil temperature at measuring point K air temperature after pressure charger K exhaust temperature K air temperature downstream of the supercharger K pressure downstream of the supercharger kpa Maximum net power :12.71 kw at 7002 min -1 Maximum net torque :20.61 Nm at 3501 min -1 TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 24 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

34 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Test minutes of anti-pollution devices Appendix 4 0. Test condition 0.1. Test date : April 12, Test site : Chutung / Taiwan 1. Test facilities : The test equipment used was in compliance with the requirements of the directive Equivalent inertia mass - acc. to section Absorbed power Pa - acc. to section 5.2. : 280 kg : 1.17 kw 1.3. Method of setting according to : Annex II, Appendix 1, point 5.2 of the directive. 2. Test vehicle(s) 2.1. Type Variant Version : SP250 : -- : SP250-S 2.2. Identification number : RK3SP03105A Masses Mass of vehicle in running order : 221 kg Reference mass : 296 kg Maximum mass of vehicle : 371 kg 2.4. Gear box Transmission type : Manual / automatic Number of gear ratios : 5 / not applicable TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 25 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

35 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Gear ratio First gear : -- Second gear : -- Third gear : -- Fourth gear : -- Fifth gear : -- Final drive ratio : 1: Tyres Front Rear Dimensions Dynamic rolling circumference mm Check of performances referred to in annex II, appendix 1, paragraph to this regulation 2.5. Tire pressure of the driven wheel on the dynamometer : Not applicable : 35 kpa TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 26 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

36 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Type I test : (Verifying the average emission of gaseous pollutants in a congested urban area) 1st measured value* 2nd measured value* 3rd measured value* CO [g/km] HC [g/km] NOx [g/km] Mean value* Test result* limit value A (2003) * Rounded value 4. Type II test : (Verifying the emission at idling speed and high idle) Idling speed 1/min CO (Vol %) oil temperature (ºC) 5. Reference fuel No. : Reference fuel according to Annex IV of 97/24/EC Chapter 5, amendment by 2005/30/EC TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 27 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

37 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Test minutes of noise-measuring Appendix 6 0. Test condition 0.1. Test date : May 5, Test site : Lung-Tan / Taiwan 1. Test facilities : The test equipment used was in compliance with the requirements of the directive. 2. Test vehicle(s) 2.1. Type : SP250 Variant : -- Version : SP250-S 2.2. Identification number : RK3SP03105A Engine 2.1. Manufacturer : Access Motor Co., Ltd Type : E Model : Four-stroke / two-stroke 2.4. Rated max. power (according to...) : 12.9 kw at 7000 min -1 (95/1/EC amendment 2002/41/EC) 2.5. Maximum design speed : 85 km/h 3. Transmission : Manual / automatic 4. Equipment 4.1. Exhaust silencer Manufacturer or authorized representative Model : Access Motor Co., Ltd. : Expansion, absorption, reflection EC type-approval number : -- TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 28 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

38 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Type Test Report No.: / /06 Access Motor Co., Ltd. SP250 : A03 In acc. with drawing no. : A03-H Air filter / Intake silencer Manufacturer or authorized representative Model : Access Motor Co., Ltd. : Air filter, dry EEC type-approval number Type in acc. with drawing no. : A03 : E / E Tyre size - front : rear : TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 29 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

39 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Measurement 5.1. Sound level of vehicle in motion Correction factor : Not applicable 1st measurement 2nd measurement Test result Measurement result Left-hand side db(a) Right-hand side db(a) db(a)/e Approach speed 50 km/h (automatic transmission without manual override) 50 km/h (automatic transmission without manual override) 5.2. Sound level of stationary vehicle 1 st measurement 2 nd measurement 3 rd measurement Test result Left db(a) Right db(a) Engine speed min db(a)/e TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 30 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

40 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP250 Test minutes of speedometer Appendix 7 0. Test condition 0.1. Test date : April 26, Test site : Tai-Bao / Taiwan 1. Test facilities : The test equipment used was in compliance with the requirements of the directive. 2. Test vehicle(s) 2.1. Type : SP250 Variant : -- Version : SP250-S 2.2. Identification number : RK3SP03105A Vehicle designed Vmax [km/h] : Mass in running order [kg] : Distribution [kg] axle 1 : 109 axle 2 : Tyre dimensions axle 1 : axle 2 : Tyre pressure [kpa] axle 1 : Speedometer axle 2 : Make(s) / type(s) : ACEWELL / ACE-3853 or KOSO / BC-SA 7.2. Speed indicated by : Digital TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 31 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

41 TÜV Kraftfahrt GmbH Accreditation: RDW Manufacturer : Type : Test Report No.: / /06 Access Motor Co., Ltd. SP Measurement 8.1. Temp at speedometer ( C) [23±5 C] : 28 C 8.2. Test result Make: ACEWELL Test Displayed speed True speed Error Limit (km/h) No V 1 (km/h) V 2 (km/h) V 1 -V 2 (km/h) Make: KOSO Test Displayed speed True speed Error Limit (km/h) No V 1 (km/h) V 2 (km/h) V 1 -V 2 (km/h) TÜV Kraftfahrt GmbH Technologiezentrum Verkehrssicherheit e6.rdw Page 32 Typprüfstelle Fahrzeuge/Fahrzeugteile Am Grauen Stein, D Köln (Poll)

42 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / /24/EC INFORMATION DOCUMENT PART 1 A. INFORMATION RELATING JOINTLY TO MOPEDS, MOTOR CYCLES, MOTOR TRICYCLES AND QUADRICYCLES 0. General 0.1. Make : Access 0.2. Type : SP250 Variant : N/A Version : SP250-S Commercial name : Access Motor, as option: SS250R, Hammel, Quadzilla, Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike 0.3. Means of type identification if stated on vehicle :???SP???????????? Location of that means of identification : On the right side of frame body, see drawing no: A03-H Vehicle category : L7e 0.5. Name and address of manufacturer Address : Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C Name(s) and address(s) of assembly plants : Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C Name and address of manufacturer s authorized representative, if any 0.7. Location and method of affixing statutory inscriptions to the chassis The serial numbering of the type begins with No Position and method of affixing the component type-approval mark for components and separate technical units : N/A : Riveted on the right side of frame body, see drawing no: A03-H00 : RK3SP03105A : Components approval marks are fixed by mold, engraving of sticker to the components. PAGE 1 / 20

43 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / General arrangement of vehicles 1.1. Photos and/or drawings of a typical vehicle : See drawing no: A03-H Dimensional drawing of the complete : See drawing no: A03-H00 vehicle Wheelbase : 1270 mm 1.3. Number of axles and wheels : Two axles, two wheels on each axle 1.4. Position and arrangement of engine : Central and vertical 1.5. Number of seating positions : Hand of drive left or right : N/A Vehicle is equipped to be driven in righthand : Both or left-hand rule of the road traffic 2. Masses 2.0. Unladen mass : 211 kg 2.1. Mass of vehicle in running order : 221 kg Distribution of that mass between the axles : Front- 109 kg, rear- 112 kg 2.2. Mass of vehicle in running order, together with rider : 296 kg Distribution of that mass between the axles : Front- 138 kg, rear- 158 kg 2.3. Maximum technically permissible mass : 371 kg declared by the manufacturer Division of that mass between the axles : Front- 152 kg, rear- 219 kg Maximum technically permissible mass on : Front- 152 kg, rear- 219 kg each of the axles 2.4. Maximum hill-starting ability at the maximum technically permissible mass declared by the manufacturer : Maximum tow-able mass : N/A 2.6. Maximum mass of the combination : N/A 3. Engine 3.0. Manufacturer : Access Motor Co., Ltd Make : Access Type : E Location of engine number : Left side of the crankcase 3.2. Spark- or compression-ignition engine Specific characteristics of the engine Operating cycle : Spark ignition, four stroke Number, arrangement and firing order of : One, vertical cylinders Bore : Ø71.0 mm PAGE 2 / 20

44 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Stroke : 63.0 mm Cylinder capacity : cc Compression ratio : 11.0± 0.1: Drawings of cylinder head, piston(s), piston rings and cylinder(s) Idling speed min -1 : 1600± 100 min Maximum net power output : 12.9 kw at 7000 min Net maximum torque : 21.0 Nm at 3500 min -1 : See drawing no: E10-H00, E10-H00, E10-000, E10-010~1, E10-010~2, E10-010~ Fuel : Diesel/ petrol/ mixture/ LPG/ other Fuel tank Maximum capacity : 14.8± 0.2 L Drawing of tank with indication of : See drawing no:12100-a03-h00 materials used Diagram clearly indicating the position of : See drawing no:12100-a03-h00 the tank on the vehicle Approval number of the fuel tank fitted : N/A Fuel supply Via carburetor(s) : Yes / no Make(s) : Mikuni Type(s) : BSR33, see drawing no: E10-H Number fitted : Settings Diffusers : Venturi, see drawing no: E10-H Level in float chamber : 31.5±0.5 mm Mass of float : 10± 0,2 g Float needle : 5 mm Fuel curve as a function of the air flow and : N/A settings required in order to maintain that curve Cold-starting system: manual/automatic : Manual / automatic Operating principle(s) : Enrich the air fuel mixture rate by using the choke mechanism to assist the cold starting. The choke is controlled by choke switch By fuel injection : Yes / no Description of system : N/A Operating principle direct / indirect / : N/A turbulence chamber injection Injection pump N/A PAGE 3 / 20

45 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Make(s) : N/A Type(s) : N/A Maximum fuel flow rate mm 3 / per stroke or : N/A cycle at a pump rotational speed of min -1 or characteristic diagram Injection advance : N/A Injection advance curve : N/A Calibration procedure: test bench/engine : N/A Regulator N/A Type : N/A Cut-off point : N/A Cut-off point under load : N/A Cut-off point under no load : N/A Idling speed : N/A Injection pipework N/A Length : N/A Internal diameter : N/A Injector(s) N/A either Make(s) : N/A Type(s) : N/A Opening pressure or characteristic diagram : N/A Cold starting system Either N/A Make(s) : N/A Type(s) : N/A Description : N/A Secondary starting device : N/A Make(s) : N/A Type(s) : N/A Description of system : N/A By fuel injection : Yes / no Description of system : N/A Operating principle: injection into Induction manifold (single/ multiple point)/direct injection/ other(state which) : N/A Make(s) of the injection pump : N/A Type(s) of the injection pump : N/A PAGE 4 / 20

46 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Injectors: opening pressure or characteristic diagram : N/A Injection advance : N/A Cold-starting system N/A Operating principle(s) : N/A Operating/setting limits : N/A Fuel pump : Yes / no Electrical equipment Nominal voltage : 12V, negative earth Generator Type : V Nominal power : 210± 5 W Ignition Make (s) : EYANG Type(s) : A Operating principle : Condenser discharge ignition Ignition advance curve or operating set point : See drawing no: A Static timing : 5 before TDC, see drawing no: A Points gap : N/A Dwell angle : N/A Anti-radio interference system : Spark plug cap with resistor and resistor spark plug Terminology and drawing of anti-radio interference equipment Indication of the nominal DC resistance value and, in the case of resistive ignition lead, statement of nominal resistance per metre Cooling system : Liquid / air Nominal setting for the engine-temperature control device : Spark plug: NGK R DPR7EA 9, see drawing no: A : Plug cap: 10± 1 kω, Spark plug: 5± 0.5 kω : Control valve opened when water is more than 75 C Liquid Nature of liquid : Long life coolant additive: 50%, water: 50% Circulating pump(s) : Yes / no Air Blower : Yes / no Induction system Supercharging : Yes / no PAGE 5 / 20

47 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Make(s) : N/A Type(s) : N/A Description of system : N/A Intercooler : With / without Description and drawings of induction pipework and accessories (plenum chamber, heating device, additional air intakes, etc.) : See drawing no: E10-010, A Description of induction manifold : See drawing no: E Air filter, drawings : See drawing no: E Make(s) : LIAN WANG Type(s) : A03 (marking: E10-000) Inlet silencer, drawings : See drawing no: E Make(s) : LIAN WANG Type(s) : A Exhaust system Drawing of complete exhaust system : See drawing no: A03-H Minimum cross-section of the inlet and : See drawing no: E10-H00 exhaust ports Induction system or equivalent data Maximum, valve lift, opening and closing angles in relation to the dead centres, or data concerning the settings of other possible systems : See drawing no e10-h Reference and/or setting ranges : ~ mm Measures taken against air pollution Device for recycling crankcase gases, : See drawing no: E10-H10 solely in the case of four-stroke engines Additional anti-pollution devices : Catalyst Catalytic converter : Yes / no Number of catalytic converters and : 1 elements Dimensions, shape and volume of the : See drawing no a catalytic converter(s) Type of catalytic action : 3 way catalytic converter PAGE 6 / 20

48 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Total charge of precious metal : See drawing no a Relative concentration : See drawing no a Substrtae (structure and material) : See drawing no a Cell density : 100 cpsi Type of casing for the catalytic converter(s) : See drawing no a Location of the catalytic converter(s) : See drawing no: A03-H Oxygen sensor : Yes / no Type : N/A Location : N/A Control range : N/A Air injection : Yes / no Type : N/A Exhaust gas recirculation : Yes / no Characteristics : N/A Other systems : N/A Location of the coefficient of absorption : N/A symbol 3.3. Electric traction motor Type : N/A Maximum continuous rated power : N/A Operating voltage : N/A Battery Number of cells : N/A Mass : N/A Capacity : N/A Location : N/A 3.4. Other motors or combinations of motors : N/A 3.5. Cooling system temperatures permitted by the manufacturer Liquid cooling Maximum temperature at outlet : 90 C Air cooling : N/A Reference point : N/A Maximum temperature at reference point : N/A 3.6. Lubrication system Description of system : Lubricant oil splashed to the cylinder camshaft by oil pump PAGE 7 / 20

49 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Location of oil reservoir : Below the crankcase Feed system : Oil pump Lubricant mixed with the fuel Percentage : N/A Oil cooler : Yes / no Drawing(s) : N/A Make(s) : N/A Type(s) : N/A 4. Transmission 4.1. Diagram of transmission system : See drawing no: E10-H Type : CVT 4.3. Clutch : Centrifugal 4.4. Gearbox Type : Automatic / manual Method of selection: by hand/foot : By hand / foot PAGE 8 / 20

50 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Gear ratios Minimum continuously variable transmission 1 2 Maximum continuously variable transmission Reverse gear N R1 R2 R3 Rt 1:1 1:1 1:1 1 st gear: 1:9.059 D gear: 1: st gear: 1:3.009 D gear: 1: : : : :2.667 N : gear ratio R1 : primary ratio (ratio of engine speed to rotational speed of primary gearbox shaft). R2 : secondary ratio (ratio of rotational speed of primary shaft to rotational speed of secondary shaft in gearbox). R3 : final drive ratio (ratio of rotational speed of gearbox output shaft to rotational speed of driven wheels). Rt : overall ratio 1 st gear: 1: D gear: 1: st gear: 1:8.026 D gear: 1: : Brief description of the electrical and/or electronic components used in the transmission 4.6. Maximum speed of vehicle and gear in which it is reached : N/A : 85 km/h 4.7. Speedometer Make(s) : ACEWELL, as option: KOSO Type(s) : ACE-3853 (ACEWELL), BC-SA (KOSO) Photographs and/or drawings of the complete system : See drawing no: A (ACEWELL), A (KOSO), A03-H speed range displayed : ACEWELL: 0~ 300 km/h KOSO: 0~ 199 km/h PAGE 9 / 20

51 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Tolerance of the measuring mechanism of the speedometer : ACEWELL km/h Tolerance 0~ +2.5% 0~ +5% Tolerance Range KOSO 0~ 1.0 km/h 0~ 3.0 km/h km/h Tolerance 0~ +5% 0~ +8.3% Tolerance Range Technical constant of the speedometer : Setting parameter: Method of operation and description of the drive mechanism Overall transmission ratio of the drive mechanism 0~ 2.0 km/h 0~ 5 km/h : Magnetic detect, digital display with back-lighting :N/A 5. Suspension 5.1. Drawing of suspension arrangement : See drawing no: A03-H Brief description of the electrical and/or electronic components used in the suspension : N/A 5.2. Tyres (category, dimensions and maximum loading) and rims (standard type) : Front Category Special Normal Size Max load 92.5 kg 92.5 kg Rim Rear Category Normal Special Normal Size Max load 132 kg 132 kg 128 kg Rim Nominal rolling circumference : Front mm, rear mm Tyre pressures recommended by the : 35 kpa manufacturer Tyre/ wheel combinations : Front / Rear / 8 9 or / Minimum-speed category symbol compatible with the theoretical maximum design speed of the vehicle : G Minimum load-capacity index with the maximum load on each tyre : Front- 19, rear Categories of use compatible for the vehicle : Front and rear- normal or special PAGE 10 / 20

52 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Steering 6.1. steering gear and control Type of gear : Handle bar on the front shaft steering Brief description of the electrical and/or electronic components used in the steering system : N/A 7. Braking 7.1. Diagram of braking devices : See drawing no a03-h Front and rear brakes, disc and/or drum : Front and rear- disc Make(s) : Horng Fuu Industrial Co.,Ltd Type(s) : Front: A (RH), A (LH) Rear: A Drawing of parts of the brake system Shoes and/or pads : N/A Linings and/or pads : See drawing no: A03-000~1, A03-000~ Brake levers and/or pedals : Brake levers: see drawing no: A A Brake pedal: see drawing no: A Hydraulic reservoirs : See drawing no: A03-000, A03-000, A Other devices: drawing and description : Mechanical parking brake device acting on the rear brake, See drawing no A03-H00, A Brief description of the electrical and/or electronic components used in the braking : N/A system 8. Lighting and light-signalling devices Trade Mark Type Quantity/ Color Tell Tale Approval No. Remark Driving lamp JUTE JUTE A013 1 / White E9-113R Passing lamp JUTE JUTE A013 1 / White N.A. E9-113R Front position lamp Front direction indicator Rear direction Indicator JUTE JUTE 0003-P 1 / White Illumination of speedometer Max lux E4-50R JUTE JUTE W016-W 2 / Amber E9-50R JUTE JUTE SAF-MR 2 / Amber E9-50R PAGE 11 / 20

53 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP /24-00 Rear position Lamp JUTE JUTE 0002-T 1 / Red Illumination of speedometer E4-50R Stop lamp JUTE JUTE 0002-T 1 / Red N.A. E4-50R License Plate illuminator Rear retro reflector JUTE JUTE 0002-T 1 / White N.A. E4-50R JUTE 9605 JUTE / Red N.A. E13*03R00*03R0 2*0279* Diagram showing the location of the lighting and light-signalling devices 8.3. Hazard warning lamps : Yes 8.4. Additional requirements relating to special : N/A vehicles 8.5. Brief description of the electrical and/or electronic components used in the lighting system and in the light-signalling system : N/A 9. Equipment 9.1. Coupling devices Type: hook/ring/other : N/A Photographs and/ or drawing showing the position and the construction of the coupling devices : N/A 9.2. Arrangement and identification of controls, tell-tales and indicators Photographs and/or drawings of the arrangement of the symbols, controls, telltales and indicators PAGE 12 / 20 : See drawing no a03-h00 : See drawing no: A03-000, A03-000, A Statutory inscriptions Photographs and/or drawings showing the location of the statutory inscriptions and the chassis number : See drawing no A03-H Photographs and/or drawings showing the official part of the inscriptions Photographs and/or drawings of the chassis number : See drawing no: A : See drawing no: A03-H Device(s) to protect against unauthorized use Type of device(s) : Type Summary description of device(s)used : Steering shaft is locked to the frame body by a lock pin, See drawing no: A03-H Audible warning device(s) Summary description of device(s) used and : One electromagnetic DC horn

54 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Make(s) : Knight Horn Type(s) : KMG-80E Type-approval mark : E13-II Drawing(s) showing the location of the audible warning device(s) in relation to the structure of the vehicle : See drawing no: A03-H Details of the method of attachment, including the part of the vehicle structure to which the audible warning device(s) is (are) attached : See drawing no: A03-H Location of rear registration plate : See drawing no: A03-H Inclination of plane in relation to the : 29 vertical B. INFORMATION RELATING SOLELY TO TWO-WHEEL MOPEDS AND MOTORCYCLES Not applicable C. INFORMATION RELATING SOLELY TO THREE-WHEEL MOPEDS, MOTOR TRICYCLES AND QUADRICYCLES 1. Dimensions and masses 1.1. Dimensions to be complied with when building unbodied chassis Length : 1825 mm Width : 1230 mm Unladen height : 1140 mm Front overhang : 255 mm Rear overhang : 300 mm Limit position for centre of gravity of bodied vehicle 1.2. Masses Maximum payload declared by manufacturer : N/A : 75 kg 2. Equipment 2.1. Bodywork Nature of bodywork : N/A General dimensional arrangement drawing : N/A of inside General dimensional arrangement drawing of outside : N/A PAGE 13 / 20

55 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Materials and methods of manufacture : N/A Passenger doors, locks and hinges : N/A Configuration, dimensions, direction and : N/A maximum opening angle of doors Drawing of locks and hinges and their : N/A location in the doors Technical description of locks and hinges : N/A 2.2. Windscreen and other glazing Windscreen Materials used : N/A Other glazing Materials used : N/A 2.3. Windscreen wiper(s) : N/A Detailed technical description : N/A 2.4. windscreen washer(s) : N/A Detailed technical description : N/A 2.5. Defrosting and demisting : N/A Detailed technical description : N/A 2.6. Rear-view mirror(s) Make : FU Type-approval mark : L-E Variant : N/A Drawing(s) showing the location of the rear-view mirror(s) in relation to the structure of the vehicle : See drawing no: A03-H Detailed information on the method of attachment, including that part of the structure of the vehicle to which the rearview mirror is attached 2.7. Seats Number : Location : Center of vehicle Coordinates or drawing of the R point Driving seat : N/A Other seats : N/A Intended seat-back inclination : N/A Driving seat : N/A Other seats : N/A PAGE 14 / 20 : Mirrors are mounted on the handle bar by using screws

56 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Seat adjustment range, where appropriate Driving seat : N/A Other seats : N/A 2.8. Passenger-compartment heating system Summary description of type of vehicle in respect of the heating system if this uses heat from the liquid engine coolant : N/A Detailed description of the type of the vehicle in respect of the heating system if this uses the cooling air or exhaust gases as a heat source, including An overall drawing of the heating system giving its location on the vehicle An overall drawing of the heat exchanger used in systems utilizing the heat from the exhaust gases, or of the parts where that exchange takes place A sectional drawing of the heat exchanger or parts where heat exchange takes place, together with a statement of the wall thickness, of the materials used and the characteristics of their surface Specifications regarding the method of manufacture and technical data relating to other major components of the heating system, such as the fan : N/A : N/A : N/A : N/A : N/A 2.9. Safety belts Number and location of safety belts, together with a reference to the seats where that type of equipment may be installed : N/A Anchorages Number and location of the anchorages : N/A Photographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages, together with an indication of the R-point position : N/A Drawings of the anchorages and the parts of the structure of the vehicle to which they are attached Designation of the types of belts(*) authorized for attachment to the anchorages on the vehicle : N/A : N/A PAGE 15 / 20

57 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP / Description of a specific type of belt, one anchorage of which is attached to the seat back-rest or incorporates an energydissipation device : N/A PAGE 16 / 20

58 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP /24-00 PART 2 SEPARATE DIRECTIVE APPROVAL NUMBERS The following information shall be supplied on the vehicle to be type approved with regard to existing system, separate technical unit or component approvals(*): Headin g No Separate Directive No Subject Approval No ( 1 ) Extension date Variants and versions covered 18 95/1/EC Maximum torque and maximum net power of engine 19 97/24/EC (C7) Anti-tampering measures for mopeds and motorcycles /24/EC (C6) Fuel tank /1/EC Maximum design speed of vehicle /93/EEC Masses and dimensions /24/EC (C10) Trailer coupling devices 28 97/24/EC (C5) Anti-air pollution measures /24/EC (C1) Tyres Front: E11-54R or E4-75R Rear: E4-75R or E11-54R or E4-75R Braking system 31 93/14/EEC 32 93/92/EEC Installation of lighting and light-signalling devices on the vehicle PAGE 17 / 20

59 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP /24-00 Headin g No Separate Directive No 33 97/24/EC (C2) Lighting and lightsignalling devices Subject Approval No( 1 ) Extension date Head lamp (high & low): E9-113R Front position lamp: E4-50R Rear position and stop lamp, rear registration lamp: E4-50R , ext.01 Front direction indicator: E9-50R Rear direction indicator: E9-50R Rear retro reflector: E13*03R00*03R02*0279* Sep Nov /30/EEC Audible warning device E13*28R00*28R00*0036* Variants and versions covered Ver. B 35 93/94/EC Position for the mounting of rear registration plate 36 97/24/EC (C8) Electromagnetic compatibility 37 97/24/EC (C9) Sound level and exhaust system /24/EC (C4) Rear-view mirror(s) E11-81R /24/EC (C3) External projections /31/EEC Stand (except in the case of vehicles having three or more wheels) 41 93/33/EEC Devices to prevent unauthorized use of the vehicle 42 97/24/EC (C12) Windows; windscreen wipers; windscreen washers; and so on 43 93/32/EEC Passenger hand-hold for two-wheel vehicles Headin Separate Directive Subject Approval No( 1 ) Extension Variants and PAGE 18 / 20

60

61 Access Motor Co., Ltd. 5, Chung-Hsin Road, Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi, Taiwan, R.O.C. Tel: Fax: Issue date: May 10, 2006 Original Application Doc. No.: SP /24-00 LIST OF CONTENTS Item Title Drawing No. Notes 1. Frame A03-H00 2. Vehicle over view A03-H00 3. Cylinder E10-H00 4. Cylinder head E10-H00 5. Piston E Piston ring 1st E10-010~1 7. Piston ring 2nd E10-010~2 8. Piston ring (oil) E10-010~3 9. Fuel cup comp A03-H Carburetor Assy E10-H CDI A Ignition coil, plug cap A Intake pipe E nd air induction valve A Air filter Assy E Inlet silencer E Exhaust muffler comp A03-H Valve angle E10-H R-crankcase venthole system E10-H Catalytic A Transmission system E10-H Speedometer A Speedometer A Speedometer system A03-H Diagram of braking system A03-H Inner pad A03-000~1 27. Outer pad A03-000~2 28. Brake lever Assy (LH) A Brake lever Assy (RH) A Brake pedal A Master cylinder A Front brake caliper (RH & LH) 31335/31336-A Rear brake caliper A Mechanical parking brake A Telltales,controls and indicators A Manufacturer s data plate A VIN code A03-H00 PAGE 20 / 20

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94