IMPORTANT SAFETY INSTRUCTIONS
|
|
- Wesley Barrett
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS READ ALL OF THESE INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE TRACK SYSTEM SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES IN THE TRACK CONFIGURATION ARE MADE THE BELOW TRACK COMPONENTS ARE FOR USE WITH "TR1" AND "TR2" TRACK ONLY. ONLY THE FOLLOWING TRACK FIXTURE SERIES ARE FOR USE WITH "TR1" AND "TR2" TRACK ONLY. IMPORTANT SAFETY INSTRUCTIONS 1) Read all instructions. 2) Do not install this track in damp or wet locations. 3) Do not cut any track sections. 4) Do not install any part of track system less than 5ft. above the floor. 5) Do not install any fixture assembly closer than 6in. from any curtain or similar combustible material. 6) Disconnect electrical power before adding or changing the configuration of the track. 7) Do not attempt to energize anything other than lighting track fixtures on the track. To reduce the risk of fire and electrical shock, do not attempt to connect power tools, extension cords, appliances, and the like to the track. 8) Track system is not intended for the use with power supply cord or convenience receptacle adapter. 9) The Track system is to be supplied by a single 120V branch circuit. 10) If track is pendant mounted, maximum pendant length is not to exceed 48in., maximum distance between pendants is 48in. SAVE THESE INSTRUCTIONS
2 INSTALLATION INSTRUCTIONS: (1) UNPACK TRACK SECTION(S) : (3) INSTALL FEEDS : (Note: Typical end feed configuration shown. See instructions included with individual feeds.) (2) MOUNT TRACK: [1] Slip the screw provided through the pre-drilled holes in the tracks and screw the toggle onto the screw. [2] Slip the toggle through the holes pre-drilled in the ceiling. [3] Tighten the screws until the track is flush to the ceiling. Do not over tighten the screw. [4] For 16 16" T-Bar suspension ceilings order: TBC, for deep tile T-Bar suspension ceilings order: TBD 1-CIRCUIT [1] Run the building supply leads through the crossbar and the nipple. [2] Attach the crossbar to the j-box (by others) with j-box screws (by others). Then screw the nipple into the crossbar. [3] Run the supply leads through the washer and the feed then the hex nut. [4] Insert the feed into the track. [5] Lightly tighten the hex nut onto the nipple. [6] Wire feed unit/s using the schematics below. Then finish tightening the hex nut. [7] Secure the canopy to the feed using screw provided. 1-Circuit Track Single circuit track is rated for 20A MAX SUPPLY. One branch circuit 120V, 20A x 120V x.8 NEC saftey factor=1920w MAX LOAD. A) B) 2-CIRCUIT [A] 2-Circuit Track With Two Feeds Two circuit track is rated for 20A Max. each conductor. One branch circuit 120/240V permits two circuits 2400w each, 20A x 120V=2400W x.8 NEC saftey factor=1920w MAX LOAD. Each conductor or 3840W LOAD TOTAL. [B] 2-Circuit Track With One Feed Two circuit track is rated 20A MAX SUPPLY. One branch circuit 120V, 20A x 120V=2400W x.8 NEC saftey factor=1920w MAX LOAD TOTAL or 960W LOAD each conductor.
3 INSTALLATION INSTRUCTIONS: (4) INSTALL CONNECTORS : (Note: These instructions can be used with all standard LSI straight, L, T and X connectors.) [1] Insert the connector into the track. Make sure the polarity arrow on the connector is aligned with the polarity groove on the track. [2] Lock the connector into the track using the integral screw provided. [3] Repeat until the configuration is complete. [4] Insert the dead end cover into open ends of the track configuration and secure with the screw provided. PENDANT INSTALLATION : [1] Install j-boxes (by others) at pendant support locations. *Note: Maximum pendant length is not to exceed 48in., maximum distance between pendants is 48in.* [2] Attach the crossbar to the j-box with the j-box screws (by others). [3] Attach one the square nut to one side of the stem. [4] Feed supply leads through the same end. [5] Slide the square nut onto the crossbar so that the stem hangs. [6] Slide the canopy up the stem until the canopy is flush with the ceiling. Tighten the canopy's locking screw to hold the canopy in place. [7] Attach the track support by sliding the other square nut through the slot in the track support. Then screw the track support onto the stem. [8] Slide the track support into the grooves on the top of the track (as shown below). For pendant feed mounting point distances see below. [9] Screw in the spreader screws until tight, this will lock the track support into place. PENDANT FEED PENDANT SUPPORT
4 Sample System Installation: Wire feed as shown below. Line up polarity arrows with the grooves and insert feeds and connectors into track sections to assemble components. LEF2 TR2 [A] 2-CIRCUIT [A] 2-Circuit Track With Two Feeds Two circuit track is rated for 20A Max. each conductor. One branch circuit 120/240V permits two circuits 2400w each, 20A x 120V=2400W x.8 NEC saftey factor=1920w MAX LOAD. Each conductor or 3840W LOAD TOTAL. [B] 2-CIRCUIT [B] 2-Circuit Track With One Feed Two circuit track is rated 20A MAX SUPPLY. One branch circuit 120V, 20A x 120V=2400W x.8 NEC saftey factor=1920w MAX LOAD TOTAL or 960W LOAD each conductor. Dot=Connector polarity arrow location =Hot side of connector/track section
5 2-Circuit Interconnection Accessories: All track components are C-UL-US listed. Installations are suitable for dry locations only. Each connector and feed accessory contains two hot (120V) conductors and a single common neutral conductor allowing for separate switching. The Maximum capacity at 120 Volts, 60Hz. is 40 Amps (20 Amps per circuit on a 120V/240V single phase, 3-wire power feed). NEC allows 80 % of full capacity or 3840 Watts maximum. Three-way Connector: Flexible Connector: Polarity-Configuration Legend: Mini Connector: LC2: 2-Circuit, 3-way connector, use as standard 'L' or reverse polarity 'L', includes optional straight cover, connector has (1) 1 2" K.O. on top that can be used as power feed, Floating Feed: Shown Mounted To Track Section FC2: 2-circuit, versitile connector allows wall to ceiling or pitched ceiling applications, ±90 horizontal range (MAX.), ±135 vertical range (MAX.), Surface Conduit Feed: MC2: 2-circuit, conductive end to end connector, specify color End Feed Kit w/box Cover: EFB2: 2-circuit, square cover plate with end feed, kit includes j-box mounting bracket, threaded nipple and nut, End Feed T-Bar: EFT2: 2-circuit, ceiling end feed has square canopy cover, (3) 1 2" K.O.'s on top can be used with T-grid installations, FF2: 2-circuit, can be installed anywhere along the track section, kit includes square j-box canopy cover, j-box mounting bracket, track adaptor and one DE series end cap, specify color. 'T' Connector: TC2: 2-Circuit, 'T' connector has (1) 1 2 " K.O. on top which can be used as a feed point, TCR2: 2-Circuit, reverse polarity 'T' connector has (1) 1 2 " K.O. on top which can be used as a feed point, Live End: Replacement Dead End: SCF2: 2-Circuit, end feed has (1) 1 2 " K.O. on top and (1) 1 2" K.O. at end for surface conduit, SCFR2: 2-Circuit, reverse polarity end feed has (1) 1 2" K.O. on top and (1) 1 2" K.O. at end for surface conduit, Three-way T-Bar: TBC2: 2-Circuit, connector has square canopy cover, (3) 1 2" K.O.'s on top can be used as a straight connector feed with T-grid installations, can be configured as a standard 'L' connector, a reverse polarity 'L' connector or a straight connector, Outlet Box Cover: 'X' Connector: EFT2: 2-circuit, 'X' connector has (1) 1 2" K.O. on top LEF2: 1 2-circuit, power feed has (1) 2 " K.O. on top for standard electrical conduit, DE: End cap for 2-circuit track, (2) supplied with every track section, that can be used as a feed point, wired as two seperate 'L' sections, OBC: Square cover plate with threaded center access hole, kit includes grounding washer, treaded nipple and nut, for use with LEF2, TBC2, TC2, TCR2 or XC2 series or 1-circuit equivalents, covers 4" octangonal j-box,
INSTALLATION INSTRUCTIONS For Light*Waves Flex II Kit with 300-Watt remote transformer
IMPORTANT SAFETY INSTRUCTIONS READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. THIS IS A 12-VOLT SYSTEM
More informationWARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS
WARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS DO NOT solder connectors as this will prohibit the adapters circuit switch to move freely from circuit to circuit. Nordic Aluminium track adapters and accessories
More informationINTEGRID TRACK (120V) SPECIFICATIONS
INTEGRID TRACK (120V) SPECIFICATIONS GENERAL Integrid Track shall be a combination Track and main runner for mech - anically supporting suspended ceiling systems. Integrid Track shall allow fixtures to
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationTRAC-LITES One Circuit Trac System TRAC SECTIONS & SYSTEM COMPONENTS R Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Reduced-profile, single-circuit trac sections for surface or pendant mounting. Compatible with a full range of feed, connector
More informationSURFACE TRACK (120/250V) SPECIFICATIONS
SURFACE TRACK (120/250V) SPECIFICATIONS GENERAL Lighting Track shall allow fixtures to be located anywhere along the track length. Fixtures shall be easily focused, switched, dimmed, accessorized and removed
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationMOUNTING SYSTEMS SPECIFICATIONS
MOUNTING SYSTEMS SPECIFICATIONS GENERAL Mounting Systems shall allow Track Systems to be fastened to or from various surfaces in a wide range of safe and approved methods. Mounting Systems shall have a
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationINSTALLATION INSTRUCTION W Track Suspension system
SAFETY INSTRUCTIONS: - Suspension mounting system should be installed by a qualified electrician only. - System is intended for installation in accordance with National Electric Code, local and - Federal
More informationNT-300 Series Single Circuit Track System & Accessories
NT-300 Series Single Circuit Track System & Accessories Type Project Catalog No. Lamp/Wattage PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated flat, solid integral copper conductors.
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationGEMINI HOUSING SPECIFICATIONS
GEMINI HOUSING SPECIFICATIONS GENERAL Gemini Housing shall support Track of six foot intervals. In addition, the extra compartment shall be able to be used for a multitude of elec trical or mechanical
More informationRECESSED TRACK (120V) SPECIFICATIONS
RECESSED TRACK (120V) SPECIFICATIONS GENERAL Recessed track shall be approved by the NEC for flush-mounting into ceiling or any flat surface. Recessed Track shall allow fixtures to be easily focused, switched,
More informationCatalog # Project. Comments. Prepared by. L653 L =12'Nominal Actual length: 140-1/8" [3559mm] W=1 3/8" [3559mm] H =11/16" [17.5mm]
Miniature size, decorator finishes, push-in connectors, economy, all combine to make single-circuit Miniature Trac perfect for residential or commercial use. Polarized connectors and end caps are molded
More informationThe lever must be placed at the lower position, when the track head is intended to be use in a one-circuit track system.
1-CIRCUIT TRACK Single circuit Extruded aluminum body Insulated solid 12-gauge copper Rated for maximum of 2400 watts Visual polarity groove Compatible with most 3-wire systems ET2 ET4 ET6 ET8 ET12 2 FT.
More informationSURFACE CONTROLTrack SPECIFICATIONS
CONTROLTrack SURFACE CONTROLTrack SPECIFICATIONS GENERAL CONTROLTrack shall allow fixtures to be located anywhere along the track length. Fixtures shall be easily focused, switched, dimmed, accessorized
More informationProject. Comments. Prepared by. 20-1/8" [511mm] 44-1/8" [1121mm] 92-1/8" [2340mm] 140-1/8" [3559mm]
DESCRIPTION Miniature size, decorator finishes, push-in connectors, economy, all combine to make single-circuit Miniature Trac perfect for residential or commercial use. Polarized connectors and end caps
More informationJuno Trac-Master Trac Lighting Systems. Comprehensive line and low voltage track systems
Juno Trac-Master Trac Lighting Systems Comprehensive line and low voltage track systems Juno Trac-Master System Safe and simple installation is what you can expect from Juno one-circuit and two-circuit
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationAlphabet By Ledra Brands
700 Track 700 Track 700 Track is a 1 circuit, 20A rated, line voltage track system. Its lightweight, compact elegant design is easy to install saving on overall project costs. The track is a 120v 1-circuit
More informationTrack Accessories. Single Circuit Track. L Connector T Connector X Connector. Mini Connector Floating Canopy End Feed Kit.
Single Circuit Single Circuit Track Live End Connector Flexible Connector Straight Connector Track supplied with dead end and mounting hardware Live end connector used for direct wiring Flexible connector
More informationHeads. track. track heads. R20 Step Cylinder. R30 Step Cylinder. R20 Soft Square. R30 Soft Square. TH204 White TH205 Black TH303 Brushed Nickel
track Heads track heads R30 Step Cylinder TH206 White TH207 Black TH304 Brushed Nickel (1) R30/PAR30 75W max. (Long Neck) Dimensions: Height 6 1 2, Width 4 1 2, Extension 8 1 2 R20 Step Cylinder TH204
More informationJuno Trac-Lites System A complete and customizable track system with an array of features
Juno Trac-Lites System A complete and customizable track system with an array of features Juno Trac-Lites System Track sections are constructed of extruded aluminum and offer a low 1/2" profile that unobtrusively
More information1Unpack fixture. Suspensions/canopies are ordered and
DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at 1-800-448-4131 questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 2Determine
More informationCOMPACT BUSWAY 40 & 60 AMP HOUSING
40 & 60 AMP HOUSING B40 & HOUSING Each Track Busway housing section consists of an extruded aluminum housing with an insulated strip containing copper conductors mounted on the top interior wall. The aluminum
More informationLSI 20 Series 30A, 120V Surface Busway Components 1
LSI Busway System LSI 20 Series 30A, 120V Surface Busway Components 1 IBEW union made at LSI plant in USA Specification grade heavy duty.075 (1.8mm) extruded aluminum busway 8 foot (2.4m) and 12 foot (3.7m)
More informationInstallation Instructions for Monorail 2 Circuit 2 X 250 Watt Sloped Surface Mount Magnetic Transformer 120 Volt Input to 12 Volt Single Feed Output
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 0 Tel: 77-770-9 Fax: 77-9- www.edgelighting.com info@edgelighting.com MT-X0--SL_ 90-MT-X0--SL-0 Installation Instructions for Monorail
More informationAlbeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series)
GE Lighting Installation Guide Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series) Features UL 1598 Suitable for Wet Locations IP66 Rated Ingress Protection BEFORE YOU BEGIN Read these
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationCetra. Ceiling Power Entry Installation (AEC1, AEC14, or AEC16)
Figure A Power Pole Top Cap Trim Plate L Bracket (Long leg attached to top of panel) Ceiling Installation (AEC, AEC, or AEC) Recommended Tools Variable Speed Drill with Torque Option Pop Rivets Riveting
More informationMuseum Alkmaar - Alkmaar, Netherlands
Museum Alkmaar - Alkmaar, Netherlands 270 Lytespan 1 283 Lytebeam 287 Universal Suspensions TRACK 292 Nanotrack 1 267 TRACK Strellson - Moscow, Russia Construction: Total Max Load: Finish: Extruded aluminium
More information4 ft 8 ft 12 ft. straight factory bent. End Cap for Recessed Track Mount for Bruck s GEO track. Offered in white, matte silver or black.
Fixture : Geo Track Geo Track GEO Track is a 2 circuit line voltage track that is surface mounted or recessed. GEO Track is lightweight, compact elegant design that is easy to install saving on overall
More informationASSEMBLY INSTRUCTIONS
A Canopy Assembly and wired by Licensed Electrician 1. Fixture Stud must be affixed to Electrical Box 2. Insert Nipple into Hickey 3. Slide Glass Canopy onto Nipple and secure with Hanger Loop with Washer.
More informationSOLAR PHOTOVOLTAIC SYSTEMS INSPECTOR CHECKLIST
SOLAR PHOTOVOLTAIC SYSTEMS INSPECTOR CHECKLIST The following checklist is an outline of the general requirements found in the 1999 National Electrical Code (NEC) Article 690 for Photovoltaic (PV) Power
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationMONORAIL KITS INSTALLATION INSTRUCTIONS PENDANTS
MONORAIL KITS PENDANTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read and unsderstand the following
More informationPDI PowerWave 2 Bus System
1 GENERAL 1.1 Summary This specification covers the electrical characteristics and general requirements for a continuous opening, low voltage, vertical or horizontal power busway distribution system. System
More informationINSTALLATION AND OPERATING INSTRUCTIONS
INSTALLATION AND OPERATING INSTRUCTIONS MANUAL TRANSFER SWITCHES FROM 0 Residential Wattage Requirements Appliance Running Watts Add watts for starting Furnace blower, gas or fuel 1/8 hp 300 500 1/8 hp
More informationINSTALLATION MANUAL ELECTRIC DOUBLE OVEN RANGE
ENGLISH ESPAÑOL INSTALLATION MANUAL ELECTRIC DOUBLE OVEN RANGE Please read these instructions thoroughly before installing and operating the range. LDE3019ST LDE3017ST LDE3017SB LDE3017SW LDE3015ST LDE3015SB
More informationHP-2 / HP-6 Direct Installation Instructions Overview
Overview Helpful Video 0-10V Dimming Step 1 Mounting & Suspension Page 2 Step 2 Identification & Preparation Page 3 Step 3 Mounting to Structure Page 4 NOTE Step 4 Page 5 This installation requires proper
More informationLAD6 6 LED Architectural Downlight
Catalog # : Project : Prepared By : Date : LAD6 6 inch LED new construction downlight delivers superior performance and energy efficiency. Designed to use anodized aluminum reflectors delivering even illumination
More informationThe installation must only be performed by a licensed electrician. Disconnect power before installing the product or servicing it.
WARNING l The installation must only be performed by a licensed electrician. l To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70)
More informationAEROBAY INSTALLATION INSTRUCTIONS
AEROBAY INSTALLATION INSTRUCTIONS AEROBAY IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical
More informationTURBO DRIVE INSTALLATION MODEL 3700T TABLE FEED Sharp, Chevalier & Others
TURBO DRIVE INSTALLATION MODEL 3700T TABLE FEED Sharp, Chevalier & Others NOTE This Turbo Drive Table Feed is configured for mounting the feed on the right hand end of the table. The lead screw pitch is
More informationElle Surface Mounting Instructions
Step 1: Preparation, page 2 Warnings CAUTION risk of fire and this product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation
More informationLAD8 8 LED Architectural Downlight
Catalog # : Project : Prepared By : Date : LAD8 8 inch LED new construction downlight delivers superior performance and energy efficiency. Designed to use anodized aluminum reflectors delivering even illumination
More informationOCEAN COUNTY ARES EMERGENCY GENERATOR USE By WX2NJ. The following was taken from September and October Ocean County ARES Newsletters in 2012:
The following was taken from September and October Ocean County ARES Newsletters in 2012: I recently purchased a used 9KW dual-fuel (gasoline/propane) generator from a gentleman in Atlantic County, who
More informationLED SMD CANOPY FLAT FIXTURE
ASD LED Canopy Lights are designed to withstand the elements while producing a lot of light. Our low profile canopy has an acrylic lens which is UV resistant and vandal-resistant. This is an ideal replacement
More informationINSTRUCTION SHEET. Installation Instructions for Mercmaster LED Luminaire. Applications. Agency Ratings. Product Safety
650457-000 INSTRUCTION SHEET Installation Instructions for Mercmaster Luminaire for proper and safe installation of this product, please read the following instructions. Applications Marine and wet locations;
More informationLAD4 4 LED Architectural Downlight
Catalog # : Project : Prepared By : Date : LAD4 4 inch LED new construction downlight delivers superior performance and energy efficiency. Designed to use anodized aluminum reflectors delivering even illumination
More informationCirca Ambient Interior Luminaire
IMPORTANT SAFETY INSTRUCTIONS 1. Read carefully before installing fixture. Retain for future reference. To prevent electrical shock, turn off electricity at fuse box before proceeding. 2. Failure to follow
More informationQ-VAULT Installation Instructions. Q-Tran, Inc. Milford, CT
QVAULT Installation Instructions QTran, Inc. Milford, CT www.qtran.com QVAULT 342694 Luminairs Landscape Lighting Systems Certified to UL 1838 Standard. 342595 Luminairs Low Voltage Lighting Systems Certified
More informationLuminaire Support Location Cable Mounting Kit. Non-Power Feed
INSTALLATION INSTRUCTIONS These installation instructions are used for installing the following luminaires and kits: Luminaire Support Location Cable Mounting Kit OLE4 (suspended) Normal Power Feed Non-Power
More informationLumination TM LED Luminaire LUR Series
Installation Guide Lumination TM LED Luminaire LUR Series BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF FIRE OR ELECTRIC SHOCK Turn power off before inspection,
More informationAssembly instruction. Pendant Light Toccata GENERAL REMARKS ON SAFETY: Technical data: BOM
GENERAL REMARKS ON SAFETY: Read all of these instructions before installing fixtures. Keep all of the instructions for future reference. Turn off power before installing fixture. Installation is to be
More informationINSTRUCTION BOOK FOR. Cosmopolitan Electrol For Sizes Up To 9' x 12'
INSTRUCTION BOOK FOR Cosmopolitan Electrol For Sizes To 9' x 12' Important Safety Instructions When using your video equipment, basic safety precautions should always be followed, including the following:
More informationEnvironmental Series Air Curtains
INSTALLATION & OPERATING INSTRUCTIONS & PARTS MANUAL FOR ALL 120 and 230 VOLT 1/4, 1/2 AND 3/4 H.P. MOTOR MODELS Environmental Series Air Curtains READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,
More informationRated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications
WPC1-XXXX-T Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications Installation Instructions: Read these instructions in their entirety before performing any installation work. FOR USE WITH
More informationEasy/Tran TF STANDBY POWER FURNACE SWITCH TOOLS NEEDED FOR INSTALLATION. PARTS LIST for Easy / Tran TF FURNACE TRANSFER SWITCH
STANDBY POWER FURNACE SWITCH Easy/Tran TF Congratulations on your purchase of the Reliance Controls Easy/Tran TF furnace transfer switch. Reliance has been manufacturing transfer switches and equipment
More informationTURBO DRIVE INSTALLATION MODEL 4380T KNEE FEED Sharp, Alliant & Others
TURBO DRIVE INSTALLATION MODEL 4380T KNEE FEED Sharp, Alliant & Others NOTE This Turbo Drive Knee Feed is configured for mounting the feed on the front of the knee with the keypad facing left. The lead
More informationThe Da-Lite Difference.
The Da-Lite Difference. Instruction Book for Cosmopolitan Electrol For Sizes Up To 9'x12' DA-LITE SCREEN COMPANY, INC. 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101
More informationLumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationUltra-Thin Recessed LED Light Installation Guide
TM PROFESSIONAL GRADE LED LIGHTING www.aspectled.com Copyright 2012-2016. aspectled, Inc. 1 OVERVIEW aspectled s Ultra-Thin series of recessed lights are bright, energy efficient, attractively styled,
More informationHIGHBAY RAIL 400W INSTALLATION INSTRUCTIONS
TM INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical Code and
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationInstallation and Maintenance Manual (2014)
TRULY GREEN SOLUTIONS 100~200W Modular LED Light Fixture Installation and Maintenance Manual (2014) 1/10 Content Warning A. Hanging Ring Mount B. Pendant Mount C. Surface Mount D. Universal Hanging Bracket
More informationI. Pendant Mount Installation
LED HIGH BAY MAX Luminaires for High Bay Applications HBM SERIES IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: 1 THIS
More informationALL700RM-230V INSTALLATION INSTRUCTIONS
ALL700RM-230V INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power source
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationDukane Projection System (DPS)
Dukane Projection System (DPS) Installation Guidelines CEILING SCREEN CAMERA SPEAKERS VCR/DVD PC 1. Determine or measure the screen width or diagonal which corresponds to your projector to find the maximum
More informationProduct Overview. High Power 7W/ft. Fixture Summary (see following pages for more information) Power Level Watts Per Foot
Linea 1.5" Pendant Direct Features Quick-Line Linea 1.5" delivers your design scenario seamlessly and on time, everytime. Streamlined and flexible, these architectural LED pendants provide the freedom
More informationWhen using electrical equipment, basic safety precautions should always be followed including the following:
INDUSTRIAL INSTALLATION INSTRUCTIONS Illumina BS100LED2FT-PLUS EACH MODEL NUMBER CONSISTS OF THE FOLLOWING: SERIES / LENGTH / OPERATION / LUMENS / COLOUR TEMP. / INPUT SERIES: LENGTH: OPERATION: BS100LED2PLUS
More informationINSTALLATION MANUAL. Melink Corporation (513) Revision
INSTALLATION MANUAL Revision 130711 Table of Contents Step Installation Contractor Page 1 Install System Controller Electrical 4 2 Install Variable Frequency Drive Electrical 6 3 Install Touchpad Mechanical
More informationHALO. Track Lighting. Metal Halide + Track = STASIS. Stasis Metal Halide
HALO Metal Halide + Track = STASIS Track Lighting Stasis Metal Halide Stasis Features Stasis Ceramic Metal Halide = The Sharp NEW Reliable Workhorse Halo once again sets the new standard in Ceramic Metal
More informationAIR CLEANERS Model MC 3000 OWNER S MANUAL CAUTION Read complete instructions before operating. Please file for future reference.
AIR CLEANERS Model MC 3000 OWNER S MANUAL CAUTION Read complete instructions before operating. Please file for future reference. MODEL MC 3000 SPECIFICATION Input Volts: 208-230/430 VAC, 60Hz, 3 Phase
More informationILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT
082114EC ILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT Beghelli Canada 3900 14th Avenue Markham, Ontario L3R 4R3 Canada P: (905) 948-9500 F: (905) 948-8673 www.beghellicanada.com Beghelli
More informationLighting tracks and adapters for innovative luminaries
Lighting tracks and adapters for innovative luminaries The lighting track system Easy to cut Cutting to the required length can be done easily on site. It is not necessary to cut back or bend the copper
More informationLED IMPORTANT SAFETY INSTRUCTIONS
LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage
More information4-11/16 Square Boxes. With Conduit Knockouts OB/SB-1. 4SJ-3/4 1-1/2 Deep, Welded. 4SJ-EK 1-1/2 Deep, Welded. 4SJD-3/4 2-1/8 Deep, Welded
4-11/16 Square Boxes With Conduit Knockouts 4SJ-3/4 1-1/2 Deep, Welded 4SJ-EK 1-1/2 Deep, Welded 4SJD-3/4 4SJD-EK 4SJD-3/4-1 4SJD-1 4SJD-1-1/4 Number Depth Cubic Inch Knockout Description Wt. Lbs. Std.
More informationTURBO DRIVE INSTALLATION MODEL 9808T KNEE FEED Kent, Kingston KTM 3V & Webb Mills
TURBO DRIVE INSTALLATION MODEL 9808T KNEE FEED Kent, Kingston KTM 3V & Webb Mills NOTE This Turbo Drive Knee Feed is configured for mounting the feed on the front of the knee with the keypad facing left.
More informationRated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications
WPC2-XXXX-T Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications Installation Instructions: Read these instructions in their entirety before performing any installation work. FOR USE WITH
More informationINSTALLATION INSTRUCTION MANUAL
INSTALLATION INSTRUCTION MANUAL LED FLOOD LIGHT, 100-277VAC MODELS: SL923FLF-15W; SL923FLF-30W; SL923FLF-50W; SL923FLF-80W; SL923FLF-100W; SL923FLF-150W; SL923FLF-300W Model number parameter list: Model
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationLED Flat Panel Installation Instructions For 1 x4, 2 x2, and 2 x4 LED Flat Panels (FP Series)
LED Flat Panel Installation Instructions For 1 x4, 2 x2, and 2 x4 LED Flat Panels (FP Series) PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION SAFETY
More informationPIL0478 ISSUE 01/ 07/16
ISSUE 01/ 07/16 PIL0478 ZAFIR G9 CEILING FITTING PIL0478 ISSUE 01/ 07/16 PART C PART E PART 21 SELV 1 1.B 1 3.1 3.3 3.4 3.5 3.6, 3.8 3.10 3.12 3.14 3.16 3.17 3.18 3.19 3.19 ATTENTION! THE TABLE BELOW
More informationArc Fault Circuit Interrupter (AFCI) FACT SHEET
Arc Fault Circuit Interrupter (AFCI) FACT SHEET THE AFCI The AFCI is an arc fault circuit interrupter. AFCIs are newly-developed electrical devices designed to protect against fires caused by arcing faults
More informationP80074 (150 amp connectors) P80071 (300 amp connectors)
Overview: The Restore-Lite Temporary Power Restoration System is a compact mobile transformer unit that contains a single-phase, floating-tap transformer designed to restore power to customers who have
More informationSteel Outlet Boxes 4 11 /16" Welded
Steel Outlet Boxes 4 11 /16" Welded Steel Outlet Boxes Features & Benefits Ideal for exposed work applications, providing an easy method for the installation of electrical devices (switches, receptacles,
More informationTrac 12/25 and Trac 12 Systems. Two uniquely qualified systems to accept Trac 12 Fixtures
Trac 12/25 and Trac 12 Systems Two uniquely qualified systems to accept Trac 12 Fixtures Juno Trac 12/25 and Trac 12 System Comparisons The original Trac 12 and the rigid profile, higher amperage Trac
More informationElectrical Applications. Metal Framing & Cable Tray Superstrut Metal Framing System. Column A. Design Data: Materials: Column B
Electrical Raceway Series 800 Surface Raceway and Lighting Systems Superstrut channel together with snap-in closure strip is listed by Underwriters Laboratories as a surface metal raceway. Other accessories
More informationMaxLite LED Linear HighBay Fixtures
Operating Instructions MaxLite LED Linear HighBay Fixtures General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions,
More informationPHOTOVOLTAIC ELECTRICAL POWER SYSTEMS INSPECTOR/INSTALLER CHECKLIST
PHOTOVOLTAIC ELECTRICAL POWER SYSTEMS INSPECTOR/INSTALLER CHECKLIST The following checklist is an outline of the general requirements found in the 2005 National Electrical Code (NEC) Article 690 for Photovoltaic
More informationG2.1 RETROFIT LED LIGHTING
INSTALLATION INSTRUCTIONS FOR CHEVRON CANOPY: G2.1 RETROFIT LED LIGHTING Please review site plans before proceeding. Contact LSI Graphic Solutions Plus Customer Service at 1-(800) 678-2001 for installation
More informationLCD4 4 LED Commercial Downlight
Catalog # : Project : Prepared By : Date : LCD4 4 inch LED new construction downlight delivers superior performance and energy efficiency. Designed to use anodized aluminum reflectors delivering even illumination
More informationDIVISION 16 - ELECTRICAL SECTION 16xx0 MANUFACTURED WIRING SYSTEM ACCESS FLOOR
DIVISION 16 - ELECTRICAL SECTION 16xx0 16xx0-1. GENERAL MANUFACTURED WIRING SYSTEM ACCESS FLOOR The modular convenience power system ensures the electrification and delivery of power from the power panels
More informationLCD6 6 LED Commercial Downlight
Catalog # : Project : Prepared By : Date : LCD6 6 inch LED new construction downlight delivers superior performance and energy efficiency. Designed to use anodized aluminum reflectors delivering even illumination
More information