ASSEMBLY INSTRUCTIONS
|
|
- Shanon Carroll
- 6 years ago
- Views:
Transcription
1 A Canopy Assembly and wired by Licensed Electrician 1. Fixture Stud must be affixed to Electrical Box 2. Insert Nipple into Hickey 3. Slide Glass Canopy onto Nipple and secure with Hanger Loop with Washer. Fixture Stud (not included) Electrical Box (not included) 3/8"--1/4" Open Hickey Ceiling Canopy (with ) 1/4" Nipple Hanger Loop with Washer 4. Open Threaded Connector by rotating nut counterclockwise. Place through Hanger Loop. (Not to be confused with Hanger Ring.) 5. Determine proper hanging height. Place link of chain through Threaded Connector. Tighten nut to close. Remove leftover chain. Threaded Connector Chain Hanger Ring Setscrew 6. Screw Threaded Pipe into Hanger Ring. Secure with Setscrew. Do NOT Overtighten. 1/2" Threaded Pipe
2 B Upper Stem Assembly Hanger Ring 1/2" Threaded Pipe Glass Ball 1. Slide Glass Ball onto Threaed Pipe followed by Glass Square Glass Square 2. Slide Upper Glass Stem onto Pipe. Glass Upper Stem Note: Stem & are packed assembled 3. Screw Threaded Washer onto end of Threaded Pipe to secure components. Do NOT overtighten. and wired by Licenced Electrician. Threaded Washer
3 1. Slide Small Arm Plate (with 5 holes) onto Pipe and follow up with Large Hex Nut with attached Pipe. Secure with Setscrew. Feed electrical wires through hex nut and connect to Small Arms. Make sure Arm Sleeves in plate are facing down. (See Fig. 1) 2. Insert Small Arms (5) into Plate holes. Secure each with Setscrew. Do NOT overtighten. (See Fig. 2) 3. Make sure arms are evenly spaced. 4. Slide Mirrored Bowl onto Threaded Pipe, followed by Slip Ring. Bowl must completely cover Small Arm Plate. Slide Slip Ring against bottom of Bowl. Secure with Setscrew. Do NOT overtighten. (See Fig. 3) 5. Slide Lower Glass Stem onto Threaded Pipe. Upper Glass Stem C First Tier Assembly Small Arm Small Arm Plate Arm Sleeve Large Hex Nut Mirrored Bowl Slip Ring Threaded Pipe Note: Stem & are packed assembled 6. Line up facets of Lower Glass Stem with that of Upper Glass Stem. 7. Screw Threaded Washer onto end of Threaded Pipe to secure components. Do NOT overtighten Lower Glass Stem Threaded Washer Figure 1 Figure 2 Figure 3
4 D Second Tier Assembly 1. Slide Large Arm Plate (with 10 holes) onto Threaded Pipe. Be certain that larger diameter of Plate is facing upwards towards First Tier Assembly. First Tier Assembly 2. Screw Small Hex Nut with attached Nipple onto end of Pipe to secure Large Arm Plate. Feed electrical wires through Small Hex Nut and connect Large Arms. Tighten Setscrew to secure Small Hex Nut. (See Fig.1) Large Arm 3. Insert Large Arms (10) into Arm Sleeves. Secure each arm with Setscrew. Do NOT overtighten. Make sure arms are spaced evenly. (See Fig. 2) 4. Insert Nipple into Small Hex Nut. Slide Large Mirrored Bowl onto Nipple. Mirrored Bowl must completely cover Large Arm Plate. Secure with Cone Nut. Do NOT overtighten. (See Fig. 3) Large Arm Plate Arm Sleeve Small Hex Nut (with Setscrew) Nipple Large Mirrored Bowl Cone Nut 5. Hang Glass Cube from Cone Nut. (See Fig. 4) Glass Cube (with hook) Figure 1 Figure 2 Figure 3 Figure 4 and wired by Licensed Electrician For customer service, please call DONGHIA
5 E Final Assembly 1. Insert 40 watt bulb into Lamp Socket. Or, if not using Lamp Shade, insert 60 watt bulb. Shown with extra chain links removed 2. Slide Glass Lamp Sleeve with metal liner over each Lamp Socket 3. Affix Lamp Shade with Flame clips to each Lamp Lamp Shade Flame Clip Glass Lamp Sleeve Bulb Lamp Socket
Assembly Instruction Sheet #IS-MCLG337RC For Style MCLG337RC
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 63.273.2700 Fax 63.23.702 www.quoizel. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire strippers,electricaltape,safetyglasses.
More informationWhen using electrical equipment, basic safety precautions should always be followed including the following:
INDUSTRIAL INSTALLATION INSTRUCTIONS Illumina BS100LED2FT-PLUS EACH MODEL NUMBER CONSISTS OF THE FOLLOWING: SERIES / LENGTH / OPERATION / LUMENS / COLOUR TEMP. / INPUT SERIES: LENGTH: OPERATION: BS100LED2PLUS
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More information(2) License Plate Plugs
PARTS LIST: 1 HD Bull Nose Bumper Assembly 12 12-1.75mm x 50mm 1 Driver/left Frame Mounting Bracket 40 12mm x 37mm OD x 3mm Flat Washers 1 Passenger/right Frame Mounting Bracket 20 12mm Lock Washers 1
More informationInstallation Instructions: Eco Linear High Bay
Installation Instructions: Eco Linear High Bay Installation Notes & Precautions: Read all precautions, warnings, instructions contained in this document. These instructions can be used to install Eco Linear
More informationINSTALLATION INSTRUCTION W Track Suspension system
SAFETY INSTRUCTIONS: - Suspension mounting system should be installed by a qualified electrician only. - System is intended for installation in accordance with National Electric Code, local and - Federal
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationTSM 610A. Installation Manual. Ver 2.4, 2014
TSM 610A Installation Manual Ver 2.4, 2014 Sewn Products Equipment Company - 971 Airport Road - Jefferson, GA 30549 Ph: 706-367-2755 Ph: 800-327-2677 Fax: 706-367-4112 www.sewnproducts.com sewnproducts@sewnproducts.com
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY FRONT BUMPER CHEVY SILVERADO 1500
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Heavy Duty Bumper Assembly 16 12mm Nylon Lock Nuts 1 Driver Mounting Bracket 8 4mm x 10mm Socket Head Screws 1 Passenger Mounting Bracket 4 Sensor Plugs 4 Support
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel. Pleasegotowww.quoizel.forproductcleaningtips.GototheCare+Maintenance selection. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire
More information2006 Saturn Ion ACCESSORIES & EQUIPMENT Doors - Ion
POWER DOOR LOCK SWITCH REPLACEMENT Removal Procedure Fig. 28: View Of Power Door Lock Switch 1. Using a flat-bladed tool, pry the switch from the door trim panel enough to expose the locking tabs. 2. Press
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationTrack Accessories. Single Circuit Track. L Connector T Connector X Connector. Mini Connector Floating Canopy End Feed Kit.
Single Circuit Single Circuit Track Live End Connector Flexible Connector Straight Connector Track supplied with dead end and mounting hardware Live end connector used for direct wiring Flexible connector
More informationC35. Assembly Instructions. Mobius Floor Lamp & C Page 1 of 7. Prepare Base (Figures 1& 2)
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 63.273.2700 Fax 63.23.702 www.quoizel. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire strippers,electricaltape,safetyglasses.
More informationVENETIA STUDIUM ICARO 3 TIERS
220-240V VENETIA STUDIUM ICARO 3 TIERS 126CAR-2 Mounting Instructions INDEX p. 3...contents of the box p. 4...warnings p. 5...electrical connections p. 6...installing the fixture p. 11...cleaning and maintenance
More informationC35 Mobius Floor Lamp & C Page 1 of 7
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationSconce INSTALLATION INSTRUCTIONS P B
INSTALLATION INSTRUCTIONS Sconce P34027 1 2017 of 8 KALLISTA Sconce INSTALLATION INSTRUCTIONS THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment
More informationRight Bar Light L Bracket Left Bar Light L Bracket. License Plate Bracket
LD1 FRONT BUMPER PART#R102616 R102619 PARTS LIST: 1 LD1 Bumper Assembly 16 10mm x 27mm OD x 3mm Flat Washers 1 Driver/left Frame Mounting Bracket 8 10mm Lock Washers 1 Passenger/right Frame Mounting Bracket
More informationInstallation Instructions: Eco SpunBay LED High Bays
Installation Instructions: Eco SpunBay LED High Bays Installation Notes & Precautions: Read all precautions, warnings, instructions contained in this document. These instructions can be used to install
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS This document explains mounting for pendant, recessed, and wall PENDANT - STEP ONE INSTALL MOUNTING POINTS Non-power feed mounting points may be positioned 1 to 12 or 12 to 18
More informationALL700RM-230V INSTALLATION INSTRUCTIONS
ALL700RM-230V INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power source
More information(2) Support Brackets (fit left or right) (2) 12mm x 40mm Bolt Plates
PARTS LIST: 1 bumper 6 12-1.75mm x 160mm Hex Bolts 2 Frame Mounting Brackets (fit left or right) 2 12-1.75mm x 50mm Hex Bolts 2 Support Brackets (fit left or right) 18 12mm x 37mm OD x 3mm Flat Washers
More informationPassenger/Right Support Bracket Driver/Left Support Bracket
PARTS LIST: 1 bumper 24 12mm x 37mm OD x 3mm Flat Washers 1 Driver/left Mounting Bracket 14 12mm Lock Washers 1 Passenger/right Mounting Bracket 14 12mm Hex Nuts 1 Driver/left Lower Support Bracket 2 Plastic
More informationCHANDELIER ITEM # MODEL # Français p. 8. Español p. 15 ATTACH YOUR RECEIPT HERE. Serial Number. Purchase Date
ITM #0394659 CHNDLIR MODL #8252-000 Français p. 8 spañol p. 5 TTCH YOUR RCIPT HR Serial Number Purchase Date Questions, problems, missing parts? efore returning to your retailer, call our customer service
More informationLicense Plate Bracket (4) Rubber Plugs. (2) Retaining Rings (2) Foam Spacers
LDB-NTIT62-FB PARTS LIST: 1 LD1 Bumper Assembly 2 8mm Hex Nuts 1 Driver/left L Bracket (center LED light) 2 6mm x 20mm Button Head Bolts 1 Passenger/right L Bracket (center LED light) 4 6mm x 18mm x 1.6mm
More informationINSTALLATION INSTRUCTIONS For Light*Waves Flex II Kit with 300-Watt remote transformer
IMPORTANT SAFETY INSTRUCTIONS READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. THIS IS A 12-VOLT SYSTEM
More informationThe lever must be placed at the lower position, when the track head is intended to be use in a one-circuit track system.
1-CIRCUIT TRACK Single circuit Extruded aluminum body Insulated solid 12-gauge copper Rated for maximum of 2400 watts Visual polarity groove Compatible with most 3-wire systems ET2 ET4 ET6 ET8 ET12 2 FT.
More informationRound or Square Type Low-Profile Housing with Toroidal Transformer for Flangeless Trims E3_LF-HDSM-WR_ 1.0
Installation Instructions for 90EHMH-LNIC Round or Square Type Low-Profile Housing with Toroidal Transformer for Flangeless Trims E_LF-HDSM-WR_.0 HALOGEN MR - ROUND/SQUARE FLANGELESS GENERAL PRODUCT INFORMATION:
More information2006 Jeep Commander ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Service Information - Commander
REMOVAL BULB Fig. 58: Remove/Install Rear Lamp Unit Bulbs NOTE: The rear lamp unit (1) contains four bulbs. For domestic vehicles they are: backup (2), park/stop (3), park/turn signal (4) and rear side
More informationVolvo - Product Code 100,1,2, 4, 6, 7, 8, 9, 10 & 112
Volvo - Product Code 100,1,2, 4, 6, 7, 8, 9, 10 & 112 Item Description Product_ Code On Hand Qty 20460353 TEMPERATURE SENSOR 100 1 3854260 DISTRIBUTOR 100 1 3854001 COIL 100 1 876839 GASKET KIT 100 1 70326595
More informationINSTRUCTIONS FOR OUTDOOR WALL LANTERN, MODEL LPT-1032
INSTRUCTIONS FOR OUTDOOR WALL LANTERN, MODEL LPT-1032 Page 1 Thank you for purchasing this Langport Lighting outdoor wall lantern. This product has been manufactured with the highest standards of safety
More informationLD1 FRONT BUMPER GMC SIERRA 1500
LDB-GSIE52-FB PARTS LIST: 1 LD1 Bumper Assembly 6 12mm Lock Washers 1 Driver/left Frame Mounting Bracket 6 12mm Hex Nuts 1 Passenger/right Frame Mounting Bracket 6 10-1.5mm x 35mm Hex Bolts 2 Tow Hook
More informationINSTALLATION INSTRUCTIONS LD-1 REAR BUMPER RAM 1500 PART#R R #PW017838
INSTALLATION INSTRUCTIONS LD-1 REAR BUMPER PART#R102617 R102620 #PW017838 PARTS LIST: 1 LD1 Bumper Assembly 4 12-1.75mm x 40mm Hex Bolts 1 Push in License Plate Light 4 12mm x 37mm x 3mm Flat Washers 2
More informationPlastic Ceiling Receptacle Lampholders
R C US Plastic Ceiling Receptacle Medium Base 250W 250V Plastic Ceiling Receptacle R-1 4.56" (115.8mm) 1.59" (40.4mm) S1174W 4.63" (117.6mm) 1.52" (38.6mm) Molded of high-temperature, thermoset plastic
More informationClutch Operated Roller Shade with Fascia Installation Instructions
Clutch Operated Roller Shade with Fascia Installation Instructions Tools Required for Installation: Power Drill & Drill Bits Installation Screws Level Pliers Measuring Tape Step #1 Bracket Installation
More informationDo not dispose of packaging until the shades are operating to your satisfaction.
for purchasing from smith+noble. Your new shade has been custom-crafted to your exact window dimensions from the highest quality materials. Once in your windows, they will provide you with a lifetime of
More informationECO-SERIES FRONT BUMPER FOR GM SIERRA #GM-19337
#GM-19337 Body Armor 4x4 272 Corporate Terrace St. Corona, CA 92879 951-808-0750 Customer Service hours: M-TH: 7:30am to 4:30 PM Pacific Time Friday: 8 AM Noon Pacific Time PARTS LIST: 1 LD1 Bumper Assembly
More informationHANGING LANTERN ITEM # MODEL #CP199MBK. Français p. 9. Español p. 17 ATTACH YOUR RECEIPT HERE. Serial Number. Purchase Date
ITEM #0650198 Portfolio is a registered trademark of LF, LLC. All Rights Reserved. ANGING LANTERN MOEL #CP199MBK Français p. 9 Español p. 17 ATTAC YOUR RECEIPT ERE Serial Number Purchase ate Questions,
More informationSconce INSTALLATION INSTRUCTIONS P34025
P34025 1 2016 of 7 KALLISTA THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product.
More informationPIL0478 ISSUE 01/ 07/16
ISSUE 01/ 07/16 PIL0478 ZAFIR G9 CEILING FITTING PIL0478 ISSUE 01/ 07/16 PART C PART E PART 21 SELV 1 1.B 1 3.1 3.3 3.4 3.5 3.6, 3.8 3.10 3.12 3.14 3.16 3.17 3.18 3.19 3.19 ATTENTION! THE TABLE BELOW
More informationIMPORTANT SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS READ ALL OF THESE INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE TRACK SYSTEM SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES IN THE TRACK CONFIGURATION
More information2015 Ford F150 Rear Bumper w/ LED
2015 Ford F150 Bumper w/ LED T527990 T527991 PARTS LIST: 1 Bumper Assembly 4 12mm Lock Washers 2 Mounting Brackets 6 12 mm Nylon Lock Nuts 4 Sensor Hole Plugs 8 4mm x 10mm Button Head Bolts 2 Plastic Plugs
More informationALL200RM/ALL200RM-CM
ALL200RM/ALL200RM-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationINSTRUCTION MANUAL SINKER. By HAY
INSTRUCTION MANUAL SINKER By HAY INTRODUCTION An elemental looking light available as either a small or large pendant. The fabric cord comes with a magnetic moulded ceiling cap in a textured finish. The
More informationSafeLite Installation Steps For a 2 x 2 Light Fixture
SafeLite Installation Steps For a 2 x 2 Light Fixture SafeLite Installation Instructions Fluorescent Fixtures (Refer to Diagrams) 1) For existing ceiling applications, remove ceiling tile from both sides
More informationAlphabet By Ledra Brands
700 Track 700 Track 700 Track is a 1 circuit, 20A rated, line voltage track system. Its lightweight, compact elegant design is easy to install saving on overall project costs. The track is a 120v 1-circuit
More informationTRAC-LITES One Circuit Trac System TRAC SECTIONS & SYSTEM COMPONENTS R Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Reduced-profile, single-circuit trac sections for surface or pendant mounting. Compatible with a full range of feed, connector
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationSURFACE CONTROLTrack SPECIFICATIONS
CONTROLTrack SURFACE CONTROLTrack SPECIFICATIONS GENERAL CONTROLTrack shall allow fixtures to be located anywhere along the track length. Fixtures shall be easily focused, switched, dimmed, accessorized
More informationILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT
082114EC ILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT Beghelli Canada 3900 14th Avenue Markham, Ontario L3R 4R3 Canada P: (905) 948-9500 F: (905) 948-8673 www.beghellicanada.com Beghelli
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationDRYING SYSTEM ASSEMBLY AND OPERATING MANUAL
Document Number: XM-DGA2PM-R0A DGA200 Rev160525 DRYING SYSTEM ASSEMBLY AND OPERATING MANUAL DRY GEAR PRO DRY GEAR PLUS w/removable Hangers FIRE RESEARCH CORPORATION www.fireresearch.com 26 Southern Blvd.,
More informationAquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationECO-SERIES REAR BUMPER FORD F150 PART # FD-2962
15-16 FORD F150 PART # FD-2962 Body Armor 4x4 272 Corporate Terrace St. Corona, CA 92879 951-808-0750 Customer Service hours: M-TH: 7:30am to 4:30 PM Pacific Time Friday: 8 AM Noon Pacific Time PARTS LIST:
More informationLED 2/3/4ft T8 Tube 120V
E-T8-1200-YR LED 2/3/4ft T8 Tube 120 Our LED Tubes utilize the latest LED chips as the light source, whilst using the standard T8 end caps, which makes it easy to install and replace traditional fluorescent
More informationSconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31421 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product. If you encounter
More informationRECESSED TRACK (120V) SPECIFICATIONS
RECESSED TRACK (120V) SPECIFICATIONS GENERAL Recessed track shall be approved by the NEC for flush-mounting into ceiling or any flat surface. Recessed Track shall allow fixtures to be easily focused, switched,
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
1 AQUALUMIN III NICHELESS POOL LIGHT INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationClutch Operated FlexShade NEXD Window shade with heavy duty clutch and 3 hardware profile. Cassette option.
INSTRUCTIONS INSTALLATION & OPERATION Overview - FlexShade Components Idler 1¼ Roller with Spline Atachment Clutch TOOLS REQUIRED Clutch PENCIL POWER DRILL Idler 1 Eliptical Hem Bar TAPE MEASURE LEVEL
More information(1) License Plate Light (2) License Plate Plugs
PARTS LIST: 1 HD Replacement Bumper 4 12mm x 40mm Hex Bolts 1 Driver/Left Bracket 4 12mm Nylon Lock Nuts 1 Passenger/Right Bracket 8 12mm x 37mm x 3mm Oversize Flat Washers 2 Thin Side Spacers 4 Rubber
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationMONORAIL KITS INSTALLATION INSTRUCTIONS PENDANTS
MONORAIL KITS PENDANTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read and unsderstand the following
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Commercial Supplemental Instructions (For use with Commercial & Industrial Sectional Doors Installation & Maintenance Manual) Things to Know Before You Begin This is a supplement
More informationTechnical Information
5 11 10 1 8 1 19 1 10 1 4 1 1 1 5 8 1 14 High Efficiency 1 1 19 14 15 1 18A 18B 4 0 18B 18A 1 MODEL B81-8100 (Basic SINGLE REDUCTION BASIC SINGLE REDUCTION UNIT (B-STYLE) ITEM # DESCRIPTION 1 HOUSING PIPE
More informationSpare Tire Access Guide (2) Plastic Plugs for License Plate on Trailer Plug Bracket Trailer Plug Bracket
LDB-CSIL55-RB PARTS LIST: 1 LD1 Bumper Assembly 12 14mm x 28mm OD x 2.5mm Flat Washers 1 Driver/left Frame Bracket 6 14mm Nylon Lock Nuts 1 Passenger/right Frame Bracket 4 12-1.75mm x 35mm Hex Bolts 1
More informationHP-2 / HP-6 Direct Installation Instructions Overview
Overview Helpful Video 0-10V Dimming Step 1 Mounting & Suspension Page 2 Step 2 Identification & Preparation Page 3 Step 3 Mounting to Structure Page 4 NOTE Step 4 Page 5 This installation requires proper
More informationALL W INSTALLATION INSTRUCTIONS
ALL1000-3300W INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power source
More informationLAMP BULB SERVICE TABLE OF CONTENTS
8L - 6 LAMPS XJ LAMP BULB SERVICE TABLE OF CONTENTS AND FRONT POSITION LAMP BULB...6 SIDE REPEATER LAMP BULB...6 AND FRONT POSITION LAMP BULB REAR FOG LAMP BULB...7 LICENSE PLATE LAMP BULB...7 (3) Pull
More informationML125T-26 Frame Parts
ML125T-26 2015Edition ML125T-26 Frame Parts 125261-1 Headlight Assy 125261-2 Headlight Housing Comp. 125261-3 Headlight Wire 125261-4 Headlight Buld 12v/35w 125261-5 Headlight Bulb 12v/5w 125261-6 Nut,
More informationSMF / DSF / DTF SMF / DSF / DTF 200
2006 SMF / DSF / DTF 200 1 The drawings in this parts book have been scaled so that parts can be easily recognized. 1 CYLINDER ASSY 2 CYLINDER ASSY Ref # Part # Description 1 410 0001A CYLINDER HEAD COVER
More informationSwell. Pablo Designs Pablo Studio 2015 Imported from China FINISHES FEATURES AND SPECIFICATIONS ADDITIONAL NOTES
FEATURES AND SPECIFICATIONS Voltage: 120V 60Hz Power consumption: 11 watts per light Color temperature: 3000K Luminosity: 800 lumens per light Luminaire efficacy: 73 lumens/watt Color rendition index:
More informationRound or Square Type Non-IC Adjustable Housing with Toroidal Transformer for Flangeless Trims E3_L_-HANM_ 1.7
Installation Instructions for 90EHMH-ANIC Round or Square Type Non-IC Adjustable Housing with Toroidal Transformer for Flangeless Trims E_L_-HANM_. HALOGEN MR - ROUND/SQUARE FLANGELESS GENERAL PRODUCT
More information49cc Prime Parts List
49cc Prime Parts List Last Revision 9/28/16 Bintelli Scooters 620 Dobbin Road Charleston, SC 29414 (843) 531-6833 Phone (843) 556-4080 Fax www.bintelliscooters.com Prime 49cc - #1 1 95201-06000-03 NUT
More informationLED Lighting for Convenience Stores, Canopies & Retail Buildings
LED Lighting for Convenience Stores, Canopies & Retail Buildings High performance LED Area Lights offer superior visibility and energy savings Full cut-off, wall mounted exterior lighting solutions engineered
More informationMP/MTFL LIGHT FIXTURE (Dimming)
Robern 701 N. Wilson Ave. Bristol, PA 19007 800.877.2376 MP/MTFL LIGHT FIXTURE (Dimming) General Notes 1. It is important that the armored cable be installed during electrical rough in. 2. When surface
More informationInstall Guide PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE
PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationPARTS CATALOGUE POWERMAX-125T REVISED 08/06/04
PARTS CATALOGUE POWERMAX-125T-7 REVISED 08/06/04 ENGINE INDEX FRAME SECTION FIG # FAN COVER/SHROUD E01 SECTION FIG # CYLINDER HEAD E02 CAMSHAFT VALVE E03 SIDE COVER F01 CAM CHAIN TENSIONER E04 R. & L.
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationMOUNTING SYSTEMS SPECIFICATIONS
MOUNTING SYSTEMS SPECIFICATIONS GENERAL Mounting Systems shall allow Track Systems to be fastened to or from various surfaces in a wide range of safe and approved methods. Mounting Systems shall have a
More informationJuno Trac-Master Trac Lighting Systems. Comprehensive line and low voltage track systems
Juno Trac-Master Trac Lighting Systems Comprehensive line and low voltage track systems Juno Trac-Master System Safe and simple installation is what you can expect from Juno one-circuit and two-circuit
More informationOperating Instructions
Operating Instructions Series L4000 Spring Driven Cord Reels 63 3 3A 3 7D 63 0 63 3 3B 63 8 63 X 6 A 63 5 63 8 3 X 6 A 63 5 63 9 L 4000 63 3 3 7 3 9 L 400 63 3 3 7A 3 9G L 4500 3 3 3 7B 63 0 Dimensions
More informationF i n i s h e d P r o d u c t S p e c i f i c a t i o n. WB Mini-Test Meter
Product No: 674057 F i n i s h e d P r o d u c t S p e c i f i c a t i o n WB Mini-Test Meter 10g nozzle 70lb ½ flask 19mm inlet/outlet 3 hanger hook Mini-Test Meter Tru-Test Inc, USA. 674057 Part Number
More informationHAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
9/23/2009 1 of 6 ITEM 1 QTY 8 Parts List PART NUMBER DESCRIPTION 3/8" CONICAL TOOTHED WASHER TOOLS REQUIRED #2 PHILLIPS SCREWDRIVER #2 STUBBY SCREWDRIVER 8mm SOCKET 13mm SOCKET RATCHET 12" EXTENSION TORQUE
More informationRectangular Linear LED High Bay
Rectangular Linear LED High Bay DESCRIPTION: Touch-Plate s Rectangular Linear High Bay was designed to provide higher lumens and even light distribution. With energy savings of up to 70% over traditional
More informationLuminaire Support Location Cable Mounting Kit. Non-Power Feed
INSTALLATION INSTRUCTIONS These installation instructions are used for installing the following luminaires and kits: Luminaire Support Location Cable Mounting Kit OLE4 (suspended) Normal Power Feed Non-Power
More informationPart No. PAFULAxxx. Figure 2
Part No. PAFULAxxx - Exhaust Vent -To be installed prior to siding- Remove the trim ring and collar from the vent assembly. Place tape or sealant between the Exhaust Vent and house. Align the tube with
More informationGTS150. Dune Buggy MINIMUM RECOMMENDED OPERATOR AGE: FOR OFF-ROAD USE ONLY. 10th letter in VIN: D-G
0-06 GTS50 0th letter in VIN: D-G Dune Buggy MINIMUM RECOMMENDED OPERATOR AGE: 6 FOR OFF-ROAD USE ONLY This vehicle is designed and manufactured for off-road use only. USA only: It does not conform to
More informationMONORAIL KITS INSTALLATION INSTRUCTIONS SPOTS
MONORAIL KITS INSTALLATION INSTRUCTIONS SPOTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read
More informationALL700/ALL700-CM INSTALLATION INSTRUCTIONS
ALL700/ALL700-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More informationTerraScreen Interior Greenwall System Field Installation Instructions (TW-4949 and TW-7049 Free-Standing)
TerraScreen Interior Greenwall System Field Installation Instructions (TW-4949 and TW-7049 Free-Standing) This instruction is a guide to installing the TerraScreen Interior Greenwall System on the free-standing
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationCustomer service: or Upper mounting ring. Canopy
Components included: Upper mounting ring Canopy Fixture base Fluorescent - 2 x 42 W 4-pin compact fluorescent lamps required (not included). Lutron recommends GE, Sylvania, or Philips lamps that are certified
More informationMicrofichesExcel. Tavola Posizione Codice Quant Ing
Tavola Posizione Codice Quant Ing 1 1 T1P52MI-A-011200 1 LH Crankcase 1 2 T1P52MI-A-011300 1 RH Crankcase 1 3 T11119 1 Crankcase gasket 1 4 TOR00037 4 Screw M5 6 1 5 T1P52MI-011400 2 Bush 1 6 T11118 2
More informationINSTALLATION INSTRUCTIONS ELEVATION REAR BUMPER FORD SUPERDUTY F #PW016687
INSTALLATION INSTRUCTIONS #PW016687 PARTS LIST: 1 Elevation Bumper Assembly 2 Plastic Plugs for license plate mount 2 2-hole Spacer Plates (for tow hitch only) 8 4mm x 10mm Socket Head Screws 4 Sensor
More information