Model: K0072. Smart Bluetooth Robot Car Kit User Guide

Size: px

Start display at page:

Download "Model: K0072. Smart Bluetooth Robot Car Kit User Guide"

Steven Jacobs
5 years ago
Views:

1 Model: K0072

3 Wheel 4 pieces Ultrasonic bracket M330 socket screws 2 bars M36 socket screws 6 bars Ultrasonic module Battery container Servo accessory 1 set M330 round head screws 8 bars Motor drive board Servo T-type fastener 8 pieces M2 nuts 2 pieces M3 nuts 16 pieces UNO R3 board for Arduino Deceleration DC motor 4 pieces Battery 2 pieces M210 round head screws 2 bars M36 round head screws 6 bars Line tracking module 5 Pin line tracking module cable 4 Pin ultrasonic module cable Battery charger M354 countersunk headscrews 2 bars HC-05 Bluetooth module Fixing tool 1 set Remote controller M24 micro servo screw 1bar M28 micro servo self-tapping screws 2bars Packing list Chassis

4 1 DC motors installation Step 1: Place the DC motor in the position marked on the chassis For example, the Front L and Front R marks should be matched between the motor and chassis Step 2: Install the DC motor 8 x M330 round head screws 4 x DC motors 8 x M3 nuts 1 x Chassis 8 x T-type fasteners

5 Step 3: Repeat the above steps

6 2 Tire installation 4 x Tires

7 3 Driver controller boards installation Step 1: Install Arduino UNO R3 4 x M3 nuts 4 x M36 socket screws 4 x M36 round head screws 1 x UNO R3 board for Arduino Step 2: Install motor driver board 1 x L293D motor drive expansion board

8 Step 3: Install Bluetooth module 1 x HC-05 Bluetooth module

9 4 Battery container installation 2 x M3 nuts 1 x Battery container 2 x M36 socket screws 2 x M354 countersunk head screws

10 5 Pan servo installation Step 1: Mount the Pan servo 1 x Servo 2 x M2 nuts 2 x M210 round head screws Step 2: Mount the accessory of the Pan servo 1 x Servo accessory 1 x M24 micro servoscrew 2 x M28 micro servo self-tappingscrews 1 x Holder for HC-SR04 Ultrasonic Module

11 Step 3: Ultrasonic Module installation 1 x HC-SR04 Ultrasonic Module

12 6 Mounting the tracking module 2 x M3 nuts 1 x Tracking module 2 x M330 socket screws 2 x M36 round head screws

13 7 Servo wiring Connect the cables in the orientation shown in the illustration below. Note the positions of the yellow and brown wires Tracking module wiring 20cm 5-Pin cable

14 9 Ultrasonic module wiring 20cm 4-Pin cable 10 Battery container wiring ----

15 11 DC motors wiring J2 connector for Front DC motors J1 connector for Rear DC motors

16 After nishing installing and wiring, please insert two batteries, push the button in the front of the motor board and wait 5 seconds for the car to work. That is not all for this car kit. There is a CD that comes with the car kit, check the CD For: Arduino example sketch and library Mobile apps to control the car Instruction manual Working modes demo and more If you: Prefer an online and updated version Do not have a CD reader Find the CD defective or missing Please go to: With additional content of: Troubleshooting User experience sharing and more Dear Customer: Thanks for using the UCTRONICS Smart Bluetooth Robot Car Kit K0072 for Arduino. You can nd more information at the links below. Please don't hesitate to let us know if you need any hands-on support from us.we love helping our customers learn and play with our products. Contact us: Custom support: support@uctronics.com Business: sales@uctronics.com Tel: Web:

ARDUINO 2WD SMART ROBOT CAR KIT

EN ARDUINO 2WD SMART ROBOT CAR KIT P a g e 2 PARTS LIST Please make sure that the following pieces are included in your kit Component Quantity Remarks Arduino Sensor Shield v5.0 1 Align pins using needle