GARO Charger GLB... -B

Transcription

1 GARO Charger GLB... -B Basic - No Load Balancing Model End User Instruction (EN) K-B-18-03

2 GARO Wallbox Assembly instructions/user Instructions (EN) EN TABLE OF CONTENTS Index Box Contents Box Contents GHL Variants Assembly Instruction for Fitters Mainboard Simplified Connection Diagram Step-by-Step Installation Setting The Charging Current Troubleshooting Technical Data Drill template (see the back of the box) GHL Wallbox Keys Manual Language labels 1 52

3 Serienr/SSI GLB GARO Wallbox Charger GLB with cable and connector, type 1 or 2 GARO Wallbox Charger GLB with type 2 socket outlet A C H D password endast wifiversion I B D F E (figure 1) A. Front cover B. Cover C. Base box (figure 3) D. Indication light G E. Key F. Connector type 1 or 2 G. Type 2 socket H. Personal protective circuit breaker, residual current circuit breaker and energy meter, if required. (figure 2) I. Serial no./ssid, password (Wi Fi version only) 3 4

4 EN Assembly instructions for fitters Circuit diagram EN RFID not available in GHL RCCB FUSE 2AT Assembly instructions for fitters Congratulations on selecting a GARO Wallbox EV Charger and contributing to a better environment. The GARO Charger is an AC charger enabling Mode 3 charging which complies fully with the requirements of IEC and IEC TS The product complies with IP Code IP44, with a closed front. It is to be fitted to a wall, and all installation must be carried out by an authorised fitter and comply with local installation regulations. L GKN A1 GK32 A2 N PE SW2 Fuse/RCCB FB Contactor FB Contactor control Line (L) Neutral (N) Protective earth (PE) A E Meter B+ Remote control A B + DataLink Max charging Factory default current (A) 16A SW1 Factory default Ext. charge control open=on, close=off *) see infobelow SW OCPP/Wi Finot available in GHL Important information for fitters: The charger must always be protected by a residual current circuit breaker and fuse. The three phase charger is equipped with a residual current circuit breaker and must be fitted with a max 32A fuse in the supply distribution box. The single phase charger is fitted with a personal protective charger with a maximum 125A fuse. Type 2 outlet L N PE * Remote control signal can be set in inverse function. See dip switch SW1(4) SW3 Reset button, Press down > 3 sec to reset WiFi back to default Access Point mode. N/A in GHL Type 2 outlet M 1. blue/brown 2. blue/red 3. blue/yellow 4. blue/green 5. white 6. red CP PP (figure 4) 5 6

5 Step-by-Step installation 1. Ensure the supply cable is not live. 2. Remove the drill template from the packaging. 3. Attach the drill template to the wall where the charger will be installed. Suitable height (see Technical data on page 45) 4. Drill/mark in accordance with the instructions on the drill template. T20 (figure 5) (figure 6) 5. Unlock the front cover with the key provided and slide the cover downwards. 6. The front cover has a built in stop position. To move past this position, grip the underside of the cover and lift outwards gradually while pulling downwards. 7. Loosen the seven screws and carefully remove the cover from the base box. 7 8

6 (figure 9) (figure 10) 15. Re install the front cover by feeding it in from below. 16. Lock the front cover with thekey. 17. Connect the power and ensure the indication light is constantly green. 18. If, not refer to the section on: Troubleshooting. 19. When the green light shines constantly, the charger is ready for use. 9 10

7 Setting The Charging Current Setting the charging current Switch 2 Depending on the size of the fuse, overload may occur, primarily at the property's meter fuse. The wallbox's charging current can be reduced using the switches on the circuit board. The supply voltage must be broken before the charging current is reduced. Setting the amperage for main fuses During installation, the amperage of the DIP switch SW1(1 2 3) must be adjusted to correspond with the size and strength of the main fuses. The DIP switch SW2(1 2 3 ) which controls the charger's maximum permitted charging current should be set to the recommended current values outlined below. Main fuse 16A 20A 25A 32A 40A 50A 63A SW1(1 2 3) 16A 20A 25A 32A 40A 50A 63A SW2(1 2 3) 13A 16A 20A 25A 32A 32A 32A S W 2 SW2 SW2 4 On = Fixed cable Off = Type 2 outlet with locking actuator Always ensure SW 4 is in ON position (figure 11) (figure 14) 11 12

8 Troubleshooting Technical data Indication Type of fault Measure Constant red light The residual current or Reset. Refer to section on personal protective current Resetting the residual current breaker or personal protective current has been tripped. breaker. Constant yellow light Broken cable Check cable Flashing yellow light Motor lock socketnot in Contact a qualified latched position. electrician No indication Check supply fuse If the measure advised does not help, contact a qualified fitter. Specification Standards/directives: IEC and IEC TS Installation: Voltage rating: Installation systems: Charging type: Mode 3 IP classification: Mechanical impact resistance: Application temperature: Storage temperature: Installation height: W eight: on wall or Garo Wallbox stand 230V/400 50Hz TT, TN and IT systems IP44 IK C C 35 0 C C metres above ground/land to lower edge of charger. around 3 kg including socket kg including cable and connector, single phase 5,4 kg including cable and connector, three phase 13 14