PERFORMANCE SPECIFICATION SHEET

Transcription

1 INCHPOUND MILPRF39006/31D 21 March 2018 SUPERSEDING MILPRF39006/31C 21 April 2011 PERFORMANCE SPECIFICATION SHEET CAPACITOR, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM (POLARIZED, SINTERED SLUG), EXTENDED RANGE, (VOLTAGE DERATED TO +125 C), ESTABLISHED RELIABILITY, STYLE CLR91 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MILPRF NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parentheses. 3. Metric equivalents are given for general information only. 4. The weld shall not be enclosed in the end seal. FIGURE 1. Style CLR91 capacitors. AMSC N/A FSC 5910

2 MILPRF39006/31D Case size L 1/ (0.79).016 (0.41) Dimensions in inches (mm) Basic case Insulated case D D ±.016 (0.41) max E ±.250 (6.35) T1.453 (11.51).188 (4.78).219 ( 5.56) (38.10) T2.641 (16.28).281 (7.14).312 ( 7.92) (57.15) T3.766 (19.46).375 (9.52).406 (10.31) (57.15) T4 62 (26.97).375 (9.52).406 (10.31) (57.15) 1/ Length of basic case sleeving shall be as specified in MILPRF QUALIFICATION: FIGURE 1. Style CLR91 capacitors Continued. A manufacturer shall be considered qualified to this specification sheet by similarity if the manufacturer is qualified to style CLR81 capacitors in MILPRF39006/25 and if the design and construction of the capacitors in this specification sheet is the same as the design and construction of the capacitors covered by MILPRF39006/25. REQUIREMENTS: Dimensions and configuration: See figure 1. Case type: Tantalum, tubular, insulated. Seal type: Hermetic (glasstotantalum anode). Terminals: Axialwire lead: Cathode and anode (type N32, N51, or N52 of MILSTD1276). Rated temperature: 55 C to, voltage derated to +125 C (see figure 2). FIGURE 2. Voltage derating with temperature. 2

3 MILPRF39006/31D Rated voltage: See table I. Capacitance () nominal (nom): See table I. tolerance: ±10 percent or ±20 percent (see table I). Failure rate level: M, P, R, and S (see table I). DC leakage (DCL) (at ): See table I. (nominal): MILSTD Dissipation factor (DF) : See table I. Seal: MILSTD202112, conditions A or D, and C. Shock (specified pulse): MILSTD202213, condition I (100 g's) or condition D (500 g's), as applicable. Vibration, high frequency: MILSTD202204, condition D (20 g's) or condition H (80 g's), as applicable. Random vibration (when applicable): MILSTD202214, test condition IIK (53.79 g's). Thermal shock: MILSTD202107, condition A (with step 3 at +125 C). The following shall apply: Number of cycles: In accordance with MILPRF DCL: 200 percent of value of table I for qualification and group C. DCL: 125 percent of value of table I for group B. Cap: Within ±5 percent of initial measurement. DF: 115 percent of initial requirement. Salt spray (corrosion): MILSTD202101, condition B (48 hours). Solderability: MILSTD Terminal strength: Pull: MILSTD202211, condition A. Wirelead bend: In accordance with MILPRF Surge voltage: See table I. Moisture resistance: MILSTD DCL: 125 percent of value of table I. Cap: Within ±8 percent of initial measurement. DF: 115 percent of initial requirement. Dielectric withstanding voltage (DWV): MILSTD ,000 V dc, minimum. Insulation resistance (IR): MILSTD202302, condition B. 100 megohms, minimum. 3

4 MILPRF39006/31D Low temperature (storage): Method 502 of MILSTD810. Cap: Within ±5 percent of initial measurement. Stability at low and high temperatures: Step 1 (): Cap: Within tolerance of table I value. Step 2 (55 C): Impedance. See table I. Cap: See table I. Step 3 (): Cap: Within ±5 percent of step 1 value. Step 4 (): Cap: See table I. Step 5 (+125 C): Cap: See table I. Step 6 (): Cap: Within ±5 percent of step 1 value. 4

5 MILPRF39006/31D Reverse voltage: As specified in MILPRF Cap: Within tolerance of table I value. Life at : MILSTD ,000 hours (qualification): Cap: Within ± 10 percent of initial measurement. 10,000 hours (group B) and extended life: DCL (): 125 percent of table I value. DCL (): See table I. Cap: Within +10 percent, 20 percent of initial measurement. DF: 200 percent of table I value. DWV: 2,000 V dc, minimum. IR.: 100 megohms, minimum. AC ripple life at (qualification and group C): Test ripple current: See table I. Test voltage: percent of rated voltage (see table I). Cap: Within ±10 percent of initial measurement. Life at +125 C: MILSTD Cap: Within ± 10 percent of initial measurement. DWV: 2,000 V dc, minimum. IR.: 100 megohms, minimum. 5

6 MILPRF39006/31D 2,000 hours (group C): DCL (+125 C): 125 percent of table I value. DCL (): See table I. Cap: Within +10 percent, 20 percent of initial measurement. DF: 200 percent of table I value. DWV: 2,000 V dc, minimum. IR.: 100 megohms, minimum. Barometric pressure: MILSTD202105, condition E (150,000 feet) (45,720.1 m). Test voltage: Rated voltage. Resistance to soldering heat: MILSTD202210, condition C. Cap: Within ±5 percent of initial measurement. Marking: In accordance with MILPRF39006, with the following exception: The manufacturer may mark the T1 case size "H" designated capacitors as follows: Polarity of all parts: Series of (+) symbols encircling positive end (see figure 1). Example: M39006/ 31H0001 JAN TM A Voltage groups ( rated voltage): I 6 V through 15 V II 25 V through 75 V. III 100 V and 125 V. 6

7 MILPRF39006/31D tolerance DC leakage +125 C Dissipation factor ESR at 2/ TABLE I. Capacitor characteristics. Impedance 7 Capacitance change at 55 C +125 C Max 40 khz ripple current 3/ µf ±% µa µa % Ohms Ohms % % % ma rms 6 V dc at 1/ 4 V dc at +125 C 1/ Surge () 6.9 V dc Case size PIN M39006/31 4/ Failure rate level (%/1,000 hrs) M() P(0.1) R(0.01) S(0.001) 220 ± ,000 T ± ,000 T ± ,500 T ± ,500 T ,500 ± ,900 T ,500 ± ,900 T ,200 ± ,300 T ,200 ± ,300 T V dc at 1/ 5 V dc at +125 C 1/ Surge () 9.2 V dc 180 ± ,000 T ± ,000 T ± ,500 T ± ,500 T ,500 ± ,900 T ,500 ± ,900 T ,800 ± ,300 T ,800 ± ,300 T V dc at 1/ 7 V dc at +125 C 1/ Surge () 11.5 V dc 150 ± T ± T ± ,450 T ± ,450 T ,200 ± ,850 T ,200 ± ,850 T ,500 ± ,300 T ,500 ± ,300 T V dc at 1/ 10 V dc at +125 C 1/ Surge () 17.2 V dc 100 ± T ± T ± ,450 T ± ,450 T ± ,800 T ± ,800 T ,000 ± ,300 T ,000 ± ,300 T V dc at 1/ 15 V dc at +125 C 1/ Surge () 28.8 V dc 68 ± T ± T ± ,400 T ± ,400 T ± ,750 T ± ,750 T ± ,100 T ± ,100 T V dc at 1/ 20 V dc at +125 C 1/ Surge () 34.5 V dc 56 ± T ± T ± ,200 T See footnotes at the end of table.

8 MILPRF39006/31D tolerance DC leakage +125 C Dissipation factor TABLE I. Capacitor characteristics Continued. ESR at 2/ Impedance Capacitance change at 55 C +125 C Max 40 khz ripple current 3/ Case size PIN M39006/31 4/ Failure rate level (%/1,000 hrs) M() P(0.1) R(0.01) S(0.001) µf ±% µa µa % Ohms Ohms % % % ma rms 30 V dc at 1/ 20 V dc at +125 C 1/ Surge () 34.5 V dc Continued. 220 ± ,200 T ± ,500 T ± ,500 T ± ,000 T ± T V dc at 1/ 30 V dc at +125 C 1/ Surge () 57.5 V dc 33 ± T ± T ± ,200 T ± ,200 T ± ,450 T ± ,450 T ± ,900 T ± ,900 T V dc at 1/ 40 V dc at +125 C 1/ Surge () 69.0 V dc 27 ± T ± T ± T ± ,100 T ± ,400 T ± ,400 T ± ,850 T ± ,850 T V dc at 1/ 50 V dc at +125 C 1/ Surge () 86.2 V dc 22 ± T ± T ± ,000 T ± ,000 T ± ,300 T ± ,300 T ± ,800 T ± ,800 T V dc at 1/ 65 V dc at +125 C 1/ Surge () V dc 10 ± T ± T ± ,300 T ± ,300 T ± ,600 T ± ,600 T ± ,000 T ± ,000 T V dc at 1/ 85 V dc at +125 C 1/ Surge () V dc 6.8 ± T ± T ± ,200 T ± ,200 T ± ,500 T See footnotes at the end of table. 8

9 MILPRF39006/31D tolerance DC leakage +125 C Dissipation factor TABLE I. Capacitor characteristics Continued. ESR at 2/ Impedance Capacitance change at 55 C +125 C Max 40 khz ripple current 3/ Case size PIN M39006/31 4/ Failure rate level (%/1,000 hrs) M() P(0.1) R(0.01) S(0.001) µf ±% µa µa % Ohms Ohms % % % ma rms 125 V dc at 1/ 85 V dc at +125 C 1/ Surge () V dc Continued. 47 ± ,500 T ± ,900 T ± ,900 T / Reverse voltage rating at is 3 V dc and at +125 C is 2 V dc. 2/ Maximum ESR is calculated by the following equation: ESR = DF, where: 2π f C DF = Maximum dissipation factor from table I; f = 120 Hz; C = Nominal capacitance. 3/ For ripple current limits at various temperatures, voltages, and frequencies, see table II. 4/ Dash number shall include the letter H to indicate the optional vibration and shock requirements (i.e., g s random vibration, 80 g s sinusoidal vibration, and 500 g s shock) or the will be deleted. The acquiring activity may substitute an H designated part in place of a non H designated part at their option. TABLE II. Ripple current multipliers versus frequency, temperature, and applied peak voltage. 1/ 2/ 3/ 4/ 5/ Frequency of applied ripple current Ambient still air temperature in C % of 100% 90% rated 80% peak 70% voltage 662/3% Frequency of applied ripple current Ambient still air temperature in C % of rated peak voltage 100% 90% 80% 70% 662/3% 120 Hz 800 Hz 1 khz khz 40 khz 100 khz / At +125 C, the rated voltage of the capacitors decreases to percent of the rated voltage. 2/ The peak of the applied ac ripple voltage plus the applied dc voltage must not exceed the dc voltage rating of the capacitor either forward or reverse. 3/ The ripple current listed in table I represents a rating calculated by using a maximum internal temperature rise ( T) at +50 C at 40 khz at ambient temperature, with a maximum peak rated voltage of percent of the peak voltage rating. 4/ The maximum allowable internal temperature rise ( T) decreases linearly to a calculated 10 C rise at +125 C ambient. 5/ The internal temperature rise is directly proportional to the ESR of the capacitor, and ESR increases with decreasing frequency. 9

10 MILPRF39006/31D Substitution of H designated parts for non H designated parts: The acquiring activity may substitute an H designated part in place of a non H designated part at their option. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MILPRF39006, this document also references: MILPRF39006/25 MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD MILSTD810 MILSTD MILSTD MILSTD1276 Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 DLA CC (Project ) Review activities: Navy AS, MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at 10