DEPARTMENT OF DEFENSE INTERFACE STANDARD
|
|
- Thomasine Watson
- 5 years ago
- Views:
Transcription
1 INCH-POUND MIL-STD-1560C 23 January 2017 SUPERSEDING MIL-STD-1560C 11 February 2015 DEPARTMENT OF DEFENSE INTERFACE STANDARD INSERT ARRANGEMENTS FOR MIL-DTL-38999, MIL-DTL-27599, AND SAE-AS29600 SERIES A ELECTRICAL CIRCULAR CONNECTORS AMSC N/A FSC 5935
2 FOREWORD 1. This standard is approved for use by all Departments and Agencies of the Department of Defense. 2. Comments, suggestions, or questions on this document should be addressed to Commander, DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus, Ohio, or ed to Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at ii
3 SUMMARY OF CHANGE 1 MODIFICATIONS 1. Change to table II, Cross-reference of insert arrangements by shell size on pages 9 through 12: Add reference to footnote 1/ next to each insert arrangement that requires either contact size 22 or 22M. Footnote 1/ states inactive for new design. Insert arrangements that specify contact sizes 22 and 22M, which are no longer used in new design, include series I arrangements 9-6, 9-44, 11-13, 13-22, 15-37, 17-55, 19-66, 19-67, 21-1, 23-1, 23-2, 25-1, 25-2, and series II arrangements 8-6, 8-44, 10-13, 12-22, 14-37, 16-42, 16-55, 18-53, 18-66, 18-67, 20-1, 20-2, 22-1, 22-2, 24-1, Except for insert arrangements 8-44 and 16-42, all of the above-referenced arrangements include the phrase (inactive for new design) within the figures themselves. Add (inactive for new design) to arrangements 8-44 and to harmonize with the other above-referenced figures. 2. Add tracer lines to insert arrangements 10-13, 10-35, and 11-35, and require contact identification numbers for contact cavities 1, 5, 10 and 13. The tracer lines are intended as a visual aid for the user to more easily locate contact cavities for insertion and removal of crimp in high density insert arrangements. In addition, update tracer line originally added to insert arrangement during revision C. MIL-STD-1560C with change 1 replaces the tracer line with its mirror image, in order for the line to follow cavity designators in sequential order. 3 Add tracer line around contact cavity A in insert arrangement The new tracer line is intended as a visual aid for the user to more easily locate contact locations in this high density insert arrangement. 4. Add requirement for tracer lines under all lower case contact cavity identification letters. The change is intended as a visual aid to better enable the user to differentiate between the upper case and lower case contact cavity identification letters in this high density insert arrangement. iii
4 CONTENTS PARAGRAPH PAGE FOREWORD... ii SUMMARY OF CHANGE 1 MODIFICATIONS... iii 1. SCOPE Scope 1 2. APPLICABLE DOCUMENTS General Government documents Specifications, standards, and handbooks Other Government documents, drawings and publications Order of precedence DEFINITIONS Definitions GENERAL REQUIREMENTS Recycled, recovered, environmentally preferable, or biobased materials DETAILED REQUIREMENTS Dimensions Marking Drawing notes NOTES Intended use Cross-reference Subject term (key word) listing Changes from previous issue FIGURE 1. Insert arrangement, electrical connector, shell size 9 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) Insert arrangement, electrical connector, shell size 11 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) Insert arrangement, electrical connector, shell size 13 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) Insert arrangement, electrical connector, shell size 15 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) Insert arrangement, electrical connector, shell size 17 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) Insert arrangement, electrical connector, shell size 19 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) Insert arrangement, electrical connector, shell size 21 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) iv
5 CONTENTS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS Insert arrangement, electrical connector, shell size 25 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) Insert arrangement, electrical connector, shell size 8 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) Insert arrangement, electrical connector, shell size 10 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) Insert arrangement, electrical connector, shell size 12 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) Insert arrangement, electrical connector, shell size 14 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) Insert arrangement, electrical connector, shell size 16 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) Insert arrangement, electrical connector, shell size 18 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) Insert arrangement, electrical connector, shell size 20 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) Insert arrangement, electrical connector, shell size 22 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) Insert arrangement, electrical connector, shell size 24 (Series II of MIL-DTL-38999, and Series II of MIL-DTL-27599) TABLE I. Cross-reference of figures to sections... 8 II. Cross-reference of figures to insert arrangements by shell size... 9 III. Cross-reference of superseded insert arrangements CONCLUDING MATERIAL v
6 1. SCOPE 1.1 Scope. This standard covers insert arrangements for use with MIL-DTL series I, II, III and IV; MIL-DTL series I and II; and SAE-AS29600 series A, circular, electrical connectors. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this standard. This section does not include documents cited in other sections of this standard or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, and 5 of this standard, whether or not they are listed. 2.2 Government documents Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL MIL-DTL Connectors, Electrical, Circular, Miniature, High Density, Quick Disconnect (Bayonet, Threaded, and Breech Coupling), Environment Resistant, Removable Crimp and Hermetic Solder s, General Specification for. - Connectors, Electrical, Circular, Miniature, Quick Disconnect, Environment Resistant, Solder s, General Specification for. (Copies of these documents are available online at Other Government documents, drawings and publications. The following other Government documents, drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DRAWINGS Electrical Connector Concentric Twinax, Socket, Shielded, Size 12 (For MIL-DTL Series I, III, and IV connectors) Electrical Connector Concentric Twinax, Pin, Shielded, Size 12 (For MIL-DTL Series I, III, and IV connectors) (Copies of DLA Land and Maritime drawings are available for download at internet web address Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. SAE INTERNATIONAL SAE-AS Connectors, Electrical, Circular, Miniature, Composite, High Density, Quick Coupling, Environment Resistant, Removable Crimp s, Associated Hardware, General Specification for. SAE-AS39029/59 - s, Electrical Connector, Socket, Crimp Removable, Shielded, Size 8 (for MIL-C Series I, III, and IV Connectors). 1
7 SAE-AS39029/60 - s, Electrical Connector, Pin, Crimp Removable, Shielded, Size 8 (for MIL-C Series I, III, and IV Connectors). SAE-AS39029/90 -, Electrical Connector, Concentric Twinax, Pin, Size 8. SAE-AS39029/91 -, Electrical Connector, Concentric Twinax, Socket, Shielded, Size 8. SAE-AS39029/113 -, Electrical Connector, Concentric Twinax, Pin, Size 8, MIL-DTL Series I, III and IV. SAE-AS39029/114 -, Electrical Connector, Concentric Twinax, Socket, Size 8, MIL-DTL Series I, III and IV. SAE-AS39029/121 - s, Electrical Connector, Socket, Crimp Removable, Expanded Performance, Sizes 10, 12, 16, 20, 22 and 23 (for MIL-DTL Series III Connectors). SAE-AS39029/122 - s, Electrical Connector, Pin, Crimp Removable, Expanded Performance, Sizes 10, 12, 16, 20, 22 and 23 (for MIL-DTL Series III Connectors). (Copies of these documents are available at or SAE International, 400 Commonwealth Drive, Warrendale, PA , and Tel: (inside USA and Canada) or (outside USA), or CustomerService@sae.org.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. DEFINITIONS 3.1 Definitions. The terms used in this standard are generally accepted by the electrical and electronics industries and are commonly used in electrical connector engineering practice, except for the following terms: a) Heat shrink sleeve. Shrink sleeves (also called heat shrink boots ) supplied with shielded are used for environmental sealing of the contact to the connector grommet cavity and to the cable. It is supplied with the contact, when specified. The sleeve is placed on the cable prior to terminating the contact. Once the cable is terminated, the shrink sleeve slides over the contact, and heat is applied to shrink the sleeve and melt the adhesive. Since the maximum temperature rating of a shrink sleeve is 175 C, a connector with a higher temperature rating will be derated to 175 C when twinax with shrink sleeves are used. b) Sealing boot. A sealing boot is a device that is used to environmentally seal a cable to a shielded electrical contact and the electrical contact to the grommet cavity within a connector insert. It is supplied with the contact, when specified. The boot is placed onto the cable prior to terminating the contact. Once the contact is installed into the connector, the boot slides forward into the grommet cavity to seal the contact to the connector. For this standard, a sealing boot may be required to be supplied with the connector for specified insert arrangements with size 8 shielded. A heat shrink sleeve is not used with a size 8 shielded contact when a sealing boot is specified. c) Inactive for new design. For this standard, insert arrangements that are specified as inactive for new design are not be used in new designs or equipment. An inactive arrangement may be used to support existing designs or equipment. 2
8 4. GENERAL REQUIREMENTS 4.1 Recycled, recovered, environmentally preferable, or biobased materials. Recycled, recovered, environmentally preferable, or biobased materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 5. DETAILED REQUIREMENTS 5.1 Dimensions. Dimensions shall be in accordance with the applicable section of this standard and the following dimensional data: a. indicates (center line) of insert arrangement. b. All dimensions are true position (TP). Dimensions are in inches, unless otherwise specified. Dimensions and markings: Front face of pin insert shown (socket insert opposite). c. dimensions- socket cavity diameter and pin engaging end diameter for each contact size: size Dimensions, socket cavity diameter and pin engaging end diameter Connector specification s, number of places as applicable insert, socket contact, contact cavity diameter 3 pin contact, engaging end diameter MIL-DTL min.0275 / MIL-DTL or MIL-DTL min.0300 ±.0005 MIL-DTL or 22D SAE-AS29600 series A.035 min.0300 ± M MIL-DTL or.036 min.0300 ±.0005 MIL-DTL MIL-DTL min.040 ± MIL-DTL or SAE-AS29600 series A.049 min.040 ± MIL-DTL min.0625 ±.0010 MIL-DTL or 16 SAE-AS29600 series A.071 min.0625 ± MIL-DTL min.094 ±.001 MIL-DTL or 12 SAE-AS29600 series A.103 min.094 ± MIL-DTL min.125 ± coax or twinax MIL-DTL or SAE-AS29600 series A.227 min.218 ±.001
9 d. Receptacle and plug gauge features: For MIL-DTL series I, II, and III, SAE AS29600 series A, and MIL-DTL series I and II receptacle connectors, functional gauge features for determining socket contact cavity locations or tip of pin contact locations shall be.002 smaller than H at MMC, and.006 smaller than GG at MMC. For MIL-DTL series I, II, and III; SAE AS29600 series A and MIL-DTL series I and II plug connectors, functional gauge features for determining socket contact cavity locations or the tip of pin contact locations shall be.002 larger than W at MMC and.006 larger than GG at MMC. Crimp removable contact tolerances shall be.015 at MMC (socket contact cavities) and.024 at MMC (tip of pin ). Fixed contact tolerances, including hermetically sealed and MIL-DTL fixed, shall be.004 at MMC. e. locations, geometric dimensioning and tolerancing requirements: Note: Some datums referenced in the below tables are found in the intermateability dimension figures in the associated connector specifications, including MIL-DTL-38999, MIL-DTL and SAE-AS For example, datums B, H, W, G, GG, F, C and L are shown in MIL-DTL Primary datum B (series I through III) is established by the plane along the surface of the front face of the receptacle shell and the plane along the surface of the front face of the plug shell. Secondary datum H is established by the inside diameter of the receptacle shell and secondary datum W is established by the outside diameter of the plug shell. Datums G and GG, which are used to establish angular orientation around the datum axis, are the centerlines of the keys or keyways. For series IV only, datum B is the front face of the receptacle shell and datum E is the front face of the plug shell. Series IV, datums L and C are established by plug and receptacle diameters. Series IV, datums H and G are used to establish angular orientation. 4
10 MIL-DTL Series I through IV (environmentally sealed with removable crimp ) Note: The pattern of the socket cavity / pin locations within the insert arrangement is constant. The pattern of the socket cavity / pin locations may shift in one direction, but the MMC modifiers on the secondary and tertiary datums do not allow socket cavity / pin position deviations within the pattern. 5
11 MIL-DTL Series I through IV (hermetically sealed with fixed ), and MIL-DTL Series I and II (environmentally sealed with fixed ) Note: The pattern of the socket cavity / pin locations within the insert arrangement is constant. The pattern of the socket cavity / pin locations may shift in one direction, but the MMC modifiers on the secondary and tertiary datums do not allow socket cavity / pin position deviations within the pattern. 6
12 SAE-AS29600, Series A (environmentally sealed with removable crimp ) Note: The pattern of the socket cavity / pin locations within the insert arrangement is constant. The pattern of the socket cavity / pin locations may shift in one direction, but the MMC modifiers on the secondary and tertiary datums do not allow socket cavity / pin position deviations within the pattern. 5.2 Marking. Marking shall be in accordance with MIL-DTL-38999, SAE-AS29600 series A, MIL-DTL-27599, and as shown in the applicable section of this standard. Sawtooth lines may be used in place of straight lines. 5.3 Drawing notes. The following information is applicable to all figures of this standard. a. Dimensions are in inches, unless otherwise specified. b. Metric equivalents are given for information only. c. Firewall applications: Insert arrangements using shielded (e.g. coax, twinax, etc.), including 17-2, 17-3, 17-11, 19-18, 19-19, 21-75, 21-76, 25-7, 25-8, 25-9, 25-10, 25-20, 25-21, 25-46, 25-47, and shall not be used in firewall connector applications. d. SAE-AS39029 : For application notes on SAE-AS39029, see MIL-DTL-38999, section 6. e. Each insert arrangement is shown using a conventional two-dimensional Cartesian system, with two perpendicular axes. The x-axis is always the horizontal axis, and the y-axis is always the vertical axis. The origin, or 0,0 point, is always where the two axes meet. The axes in each insert arrangement follow the standard two-dimensional, positive orientation, with the positive x-axis pointed to the right and the positive y-axis pointed up. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. This standard covers insert arrangements for use with MIL-DTL series I, II, III and IV; MIL-DTL series I and II; and SAE-AS29600 series A circular connectors. Information pertaining to shell size, arrangement number, number of, size of, service rating, contact location, and superseding information is contained in this document. 6.2 Cross-reference. See table I for a cross-reference of previous sections and current figures. See table II for a hyperlinked cross-reference to insert arrangement numbers by shell size. See table III for a cross-reference of superseded insert arrangements. 7
13 Title Insert arrangement, electrical connector, shell size 9 Insert arrangement, electrical connector, shell size 11 Insert arrangement, electrical connector, shell size 13 Insert arrangement, electrical connector, shell size 15 Insert arrangement, electrical connector, shell size 17 Insert arrangement, electrical connector, shell size 19 Insert arrangement, electrical connector, shell size 21 Insert arrangement, electrical connector, shell size 23 Insert arrangement, electrical connector, shell size 25 Insert arrangement, electrical connector, shell size 8 Insert arrangement, electrical connector, shell size 10 Insert arrangement, electrical connector, shell size 12 Insert arrangement, electrical connector, shell size 14 Insert arrangement, electrical connector, shell size 16 Insert arrangement, electrical connector, shell size 18 Insert arrangement, electrical connector, shell size 20 Insert arrangement, electrical connector, shell size 22 Insert arrangement, electrical connector, shell size 24 TABLE I. Cross-reference of figures to sections. Current figure Previous section Document MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL SAE-AS29600 MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL MIL-DTL Series I,III, IV I A I,III, IV I A I,III, IV I A I,III, IV I A I,III, IV I A I,III, IV I A I,III, IV I A I,III, IV I A I,III, IV I A II II II II II II II II II II II II II II II II II II 8
14 TABLE II. Cross-reference to insert arrangements by shell size. Shell size 9, figure 1 Insert arrangement Page Insert arrangement Page / / See footnotes at end of table. Shell size 11, figure 2 Insert arrangement Page Insert arrangement Page / See footnotes at end of table. Shell size 13, figure 3 Insert arrangement Page Insert arrangement Page / See footnotes at end of table. Shell size 15, figure 4 Insert arrangement Page Insert arrangement Page / See footnotes at end of table. Shell size 17, figure 5 Insert arrangement Page Insert arrangement Page / / / See footnotes at end of table. 9
15 TABLE II. Cross-reference to insert arrangements by shell size - Shell size 19, figure 6 Insert arrangement Page Insert arrangement Page / / / / See footnotes at end of table. Shell size 21, figure 7 Insert arrangement Page Insert arrangement Page / / / See footnotes at end of table. Shell size 23, figure 8 Insert arrangement Page Insert arrangement Page / / See footnotes at end of table. Shell size 25, figure 9 Insert arrangement Page Insert arrangement Page / / / / / / / / / / / / 167 See footnotes at end of table. 10
16 TABLE II. Cross-reference to insert arrangements by shell size - Shell size 8, figure 10 Insert arrangement Page Insert arrangement Page 8-3 1/ / See footnotes at end of table. Shell size 10, figure 11 Insert arrangement Page Insert arrangement Page / See footnotes at end of table. Shell size 12, figure 12 Insert arrangement Page Insert arrangement Page / See footnotes at end of table. Shell size 14, figure 13 Insert arrangement Page Insert arrangement Page / See footnotes at end of table. Shell size 16, figure 14 Insert arrangement Page Insert arrangement Page 16-6 / / / See footnotes at end of table. Shell size 18, figure 15 Insert arrangement Page Insert arrangement Page / / / See footnotes at end of table. 11
17 TABLE II. Cross-reference to insert arrangements by shell size - Shell size 20, figure 16 Insert arrangement Page Insert arrangement Page / / See footnotes at end of table. Shell size 22, figure 17 Insert arrangement Page Insert arrangement Page / / See footnotes at end of table. Shell size 24, figure 18 Insert arrangement Page Insert arrangement Page / / / Inactive for new design. 2/ To ensure environmental sealing, size 8 shielded for this insert arrangement require sealing boots in accordance with MIL-DTL-38999/62. 12
18 TABLE III. Cross-reference of superseded insert arrangements. 1/ Superseded insert arrangement number 2/ 6.3 Subject term (key word) listing. Coax Heat shrink sleeve Insert Shell size Sealing boot Socket Twinax Pin Superseded by insert arrangement number 3/ / Superseded arrangements are inactive for new design, but are still available for use in existing designs. 2/ Inactive for new design. Note: To meet environmental sealing requirements, size 8 shielded used with these insert arrangements may require separate, non-standard sealing boots that are furnished with the connector. For these insert arrangements, some connector grommet designs use a heat shrink sleeve only with specified size 8 shielded to meet environmental sealing requirements. Heat shrink sleeves have a maximum temperature rating of 175 C maximum. When heat shrink sleeves are used, connectors rated to 200 C max are derated to 175 C max. When heat shrink sleeves are used, sealing boots are not used, and when sealing boots are used, heat shrink sleeves are not used. 3/ To ensure environmental sealing, size 8 shielded for these insert arrangements require sealing boots in accordance with MIL-DTL-38999/62. Required sealing boots are furnished with the connector. When sealing boots are used, heat shrink sleeves are not used. 6.4 Changes from previous issue. The margins of this standard are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the previous issue. 13
19 position identification () s (Insert arrangement 9-3) location A (1.42) (0.46) B (0.00) (2.01) C (1.42) (0.46) (Applicable to MIL-DTL only) Shell size Arrangement no. Number of Size Service rating location Supersedes M All MS FIGURE 1. Insert arrangement, electrical connector, shell size 9 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600). 14
20 position s (Insert arrangement 9-6) location (1.14) (1.98) (1.98) (1.14) (0.00) (2.29) (1.98) (1.14) (1.14) (1.98) (0.00) (0.00) Shell size (Inactive for new design for MIL-DTL and SAE-AS29600) Arrangement Number of Size Service no. rating location Supersedes M M All MS FIGURE 1. Insert arrangement, electrical connector, shell size 9 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 15
21 position s (Insert arrangement 9-7) mm (inches) location mm (inches) A (.046) (.081) B (.093) (0.00) C (.046 ) (-.081) D (-.046) (-.081) E (-.093) (0.00) F (-.046) (.081) G (0.00) (0.00) Shell size (Applicable to MIL-DTL only) Arrangement Number of Size Service no. rating location D M All FIGURE 1. Insert arrangement, electrical connector, shell size 9 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 16
22 position s (Insert arrangement 9-23) position (0.00) (2.67) (1.89) (1.89) (1.89) (1.89) (2.67) (0.00) (2.67) (0.00) (1.89) (1.89) (1.89) (1.89) (0.00) (0.00) (0.00) (2.67) Shell size Arrangement no. Number of Size Service rating location N ALL Standard contact Pin Socket M39029/ M39029/ FIGURE 1. Insert arrangement, electrical connector, shell size 9 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 17
23 position s (Insert arrangement 9-35) location (1.14) (1.98) (1.98) (1.14) (0.00) (2.29) (1.98) (1.14) (1.14) (1.98) (0.00) (0.00) Shell size (Applicable to MIL-DTL and SAE-AS29600) Arrangement Number of Size Service no. rating location Supersedes D M All MS FIGURE 1. Insert arrangement, electrical connector, shell size 9 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 18
24 position s (Insert arrangement 9-44) location (0.00) (2.06) (2.03) (0.53) (0.00) (1.27) (2.03) (0.53) Shell size (Inactive for new design for MIL-DTL and SAE-AS29600) Arrangement Number of Size Service no. rating location Supersedes M All MS FIGURE 1. Insert arrangement, electrical connector, shell size 9 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 19
25 position s (Insert arrangement 9-98) location A (1.65) (0.97) B (0.00) (1.91) C (1.65) (0.97) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 1. Insert arrangement, electrical connector, shell size 9 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 20
26 + Y -X + X - Y position s (Insert arrangement 11-2) location A (2.41) (.00) B (2.41) (.00) Shell Arrangement Number of Size Service size no. rating location I All FIGURE 2. Insert arrangement, electrical connector, shell size 11 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 21
27 + X position s (Insert arrangement 11-4) location A (1.65) (1.65) B (1.65) (1.65) C (1.65) (1.65) D (1.65) (1.65) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 2. Insert arrangement, electrical connector, shell size 11 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600). 22
28 + X position s (Insert arrangement 11-5) location A (1.65) (1.42) B (2.87) (1.65) C (0.00) (3.30) D (2.87) (1.65) E (1.65) (1.42) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 2. Insert arrangement, electrical connector, shell size 11 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 23
29 s (Insert arrangement 11-13) (0.00) (3.71) (3.51) (1.14) (2.16) (3.00) (3.51) (1.14) (3.51) (1.14) (2.16) (3.00) (3.51) (1.14) (0.00) (1.42) (2.16) (3.00) (1.24) (0.89) (0.00) (3.71) (1.24) (0.89) (2.16) (3.00) Shell size Arrangement no. (Inactive for new design for MIL-DTL-38999) Number of Size Service rating location Supersedes M M ALL MS FIGURE 2. Insert arrangement, electrical connector, shell size 11 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 24
30 s (Insert arrangement 11-23) (0.00) (4.08) (3.53) (2.04) (1.77) (3.06) (1.77) (3.06) (3.53) (2.04) (0.00) (2.04) (3.53) (0.00) (1.77) (1.02) (3.53) (2.04) (1.77) (1.02) (1.77) (3.06) (0.00) (2.04) (0.00) (4.08) (1.77) (1.02) (1.77) (3.06) (1.77) (1.02) (3.53) (2.04) (0.00) (0.00) (3.53) (0.00) Shell size Arrangement no. Number of Size Service rating location N ALL Standard contact Pin Socket M39029/ M39029/ FIGURE 2. Insert arrangement, electrical connector, shell size 11 (Series I, III, IV of MIL-DTL38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 25
31 s (Insert arrangement 11-35) (0.00) (3.71) (3.51) (1.14) (2.16) (3.00) (3.51) (1.14) (3.51) (1.14) (2.16) (3.00) (3.51) (1.14) (0.00) (1.42) (2.16) (3.00) (1.24) (0.89) (0.00) (3.71) (1.24) (0.89) (2.16) (3.00) Shell size Arrangement no. (Applicable to MIL-DTL only) Number of Size Service rating location Supersedes D M All MS FIGURE 2. Insert arrangement, electrical connector, shell size 11 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 26
32 position s (Insert arrangement 11-98) location A (0.00) (3.30) B (3.30) (0.00) C (1.65) (2.87) D (1.65) (2.87) E (3.30) (0.00) F (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 2. Insert arrangement, electrical connector, shell size 11 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 27
33 position s (Insert arrangement 11-99) A (1.65) (2.87) B (3.30) (0.00) C (1.65) (2.87) D (1.65) (2.87) E (3.30) (0.00) F (1.65) (2.87) G (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 2. Insert arrangement, electrical connector, shell size 11 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 28
34 s (Insert arrangement 13-4) A (0.00) (3.81) B (3.71) (0.89) C (0.00) (2.11) D (3.71) (0.89) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 3. Insert arrangement, electrical connector, shell size 13 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600). 29
35 position s (Insert arrangement 13-8) location A (1.65) (3.99) B (4.32) (0.00) C (3.05) (3.05) D (0.00) (4.32) E (3.05) (3.05) F (4.32) (0.00) G (1.65) (3.99) H (0.00) (1.12) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 3. Insert arrangement, electrical connector, shell size 13 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 30
36 + Y - X + X position Shell size s (Insert arrangement 13-22) position (1.14) (5.00) (4.62) (2.24) (3.20) (4.01) (3.20) (4.01) (4.62) (2.24) (1.14) (5.00) (5.16) (0.00) (1.14) (2.72) (4.62) (2.24) (2.97) (0.66) (3.20) (4.01) (2.36) (1.91) (1.14) (5.00) (0.00) (3.05) (1.14) (5.00) (2.36) (1.91) (3.20) (4.01) (2.97) (0.66) (4.62) (2.24) (1.14) (2.72) (5.16) (0.00) (0.00) (0.76) Arrangement no. (Inactive for new design for MIL-DTL-38999) Number of Size Service rating location Supersedes M M All MS FIGURE 3. Insert arrangement, electrical connector, shell size 13 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) - Y 31
37 FIGURE 3. Insert arrangement, electrical connector, shell size 13 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 32
38 s (Insert arrangement 13-23) (0.00) (5.68) (2.05) (5.30) (2.05) (5.30) (0.00) (3.64) (3.83) (4.20) (1.97) (3.06) (5.09) (2.53) (3.31) (1.51) (5.66) (0.52) (3.60) (0.52) (5.46) (1.55) (2.75) (2.38) (4.53) (3.42) (1.03) (3.49) (2.99) (4.83) (1.03) (3.49) (1.04) (5.58) (2.75) (2.38) (1.04) (5.58) (3.60) (0.52) (2.99) (4.83) (3.31) (1.51) (4.53) (3.42) (1.97) (3.06) (5.46) (1.55) (0.00) (1.60) (5.66) (0.52) (1.60) (0.00) (5.09) (2.53) (0.00) (1.60) (3.83) (4.20) (1.60) (0.00) Shell size Arrangement no. Number of Size Service rating location N All Standard contact Pin Socket M39029/ M39029/ FIGURE 3. Insert arrangement, electrical connector, shell size 13 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 33
39 + Y - X + X s (Insert arrangement 13-35) position position (1.14) (5.00) (4.62) (2.24) (3.20) (4.01) (3.20) (4.01) (4.62) (2.24) (1.14) (5.00) (5.16) (0.00) (1.14) (2.72) (4.62) (2.24) (2.97) (0.66) (3.20) (4.01) (2.36) (1.91) (1.14) (5.00) (.00) (3.05) (1.14) (5.00) (2.36) (1.91) (3.20) (4.01) (2.97) (0.66) (4.62) (2.24) (1.14) (2.72) (5.16) (0.00) (.00) (0.76) Shell size Arrangement no. (Applicable to MIL-DTL only) Number of Size Service rating location Supersedes D M All MS FIGURE 3. Insert arrangement, electrical connector, shell size 13 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) - Y 34
40 s (Insert arrangement 13-98) A (0.00) (4.95) B (3.18) (3.81) C (4.90) (0.76) D (4.17) (2.67) E (0.00) (3.43) F (4.17) (2.67) G (4.90) (0.76) H (3.18) (3.81) J (1.65) (0.38) K (1.65) (0.38) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 3. Insert arrangement, electrical connector, shell size 13 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 35
41 s (Insert arrangement 15-5) A (0.00) (2.54) B (4.42) (0.61) C (2.39) (3.76) D (2.39) (3.76) E (4.42) (0.61) Shell size Arrangement no. Number of Size Service rating location Supersedes II All MS FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600). 36
42 s (Insert arrangement 15-15) A (2.54) (5.72) J (6.20) (0.36) B (5.13) (3.56) K (5.13) (3.56) C (6.20) (0.36) L (2.54) (5.72) D (5.54) (2.87) M (.00) (3.56) E (3.20) (5.31) N (2.79) (1.02) F (.00) (6.22) P (.00) (1.96) G (3.20) (5.31) R (2.79) (1.02) H (5.54) (2.87) Shell size Arrangement no Number of Size Service rating location P 1 16 I All other Supersedes MS FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 37
43 s (Insert arrangement 15-18) A (1.65) (6.40) K (4.95) (2.87) B (4.95) (2.87) L (1.65) (6.40) C (6.60) (0.00) M (1.65) (2.87) D (4.95) (2.87) N (1.65) (2.87) E (3.30) (5.72) P (3.30) (0.00) F (0.00) (5.72) R (1.65) (2.87) G (3.30) (5.72) S (1.65) (2.87) H (4.95) (2.87) T (3.30) (0.00) J (6.60) (0.00) U (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 38
44 s (Insert arrangement 15-19) position A (0.00) (5.72) L (4.95) (2.87) B (3.30) (5.72) M (3.30) (5.72) C (4.95) (2.87) N (1.65) (2.87) D (6.60) (0.00) P (1.65) (2.87) E (4.95) (2.87) R (3.30) (0.00) F (3.30) (5.72) S (1.65) (2.87) G (0.00) (5.72) T (1.65) (2.87) H (3.30) (5.72) U (3.30) (0.00) J (4.95) (2.87) V (0.00) (0.00) K (6.60) (0.00) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 39
45 position s (Insert arrangement 15-21) 40 A (2.68) (6.15) M (2.04) (6.10) B (6.35) (1.91) N (0.00) (4.70) C (6.86) (.051) P (3.05) (2.92) D (5.46) (3.18) R (4.32) (0.51) E (3.48) (5.61) S (2.41) (3.56) F (1.22) (6.50) T (0.00) (4.32) G (1.22) (6.50) U (2.41) (3.56) H (3.48) (5.61) V (4.32) (0.51) J (5.46) (3.18) W (3.05) (2.92) K (6.86) (0.51) X (0.00) (0.00) L (6.35) (1.91) FIGURE 4. Insert arrangement, electrical connector, shell size 15 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600)
46 Shell size Arrangement no Number of Size Service rating position Pin Standard contact Socket M39029/ Coax X M39029/ D, J, N M39029/ M39029/ I 17 22D All others M39029/ M39029/ FIGURE 4. Insert arrangement, electrical connector, shell size 15 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 41
47 position s (Insert arrangement 15-23) (2.04) (7.07) (2.04) (0.00) (0.00) (7.07) (4.08) (0.00) (2.04) (7.07) (6.12) (0.00) (5.10) (5.30) (7.14) (1.77) (3.06) (5.30) (5.10) (1.77) (1.02) (5.30) (3.06) (1.77) (1.02) (5.30) (1.02) (1.77) (3.06) (5.30) (1.02) (1.77) (5.10) (5.30) (3.06) (1.77) (6.12) (3.53) (5.10) (1.77) (4.08) (3.53) (7.14) (1.77) FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 42
48 s (Insert arrangement 15-23) position (2.04) (3.53) (6.12) (3.53) (0.00) (3.53) (4.08) (3.53) (2.04) (3.53) (2.04) (3.53) (4.08) (3.53) (0.00) (3.53) (6.12) (3.53) (2.04) (3.53) (7.14) (1.77) (4.08) (3.53) (5.10) (1.77) (6.12) (3.53) (3.06) (1.77) (5.10) (5.30) (1.02) (1.77) (3.06) (5.30) (1.02) (1.77) (1.02) (5.30) (3.06) (1.77) (1.02) (5.30) (5.10) (1.77) (3.06) (5.30) (7.14) (1.77) (5.10) (5.30) (6.12) (0.00) (2.04) (7.07) (4.08) (0.00) (0.00) (7.07) (2.04) (0.00) (2.04) (7.07) (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location N All Standard contact Pin Socket M39029/ M39029/ FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 43
49 s (Insert arrangement 15-35) (1.14) (6.65) (3.12) (3.02) (3.12) (5.51) (4.32) (1.02) (5.36) (4.06) (4.32) (1.27) (6.45) (2.03) (3.12) (3.23) (6.76) (.25) (1.14) (4.37) (6.27) (2.49) (1.14) (4.37) (5.08) (4.45) (3.12) (3.23) (3.30) (5.89) (4.32) (1.27) (1.14) (6.65) (4.32) (1.02) (1.14) (6.65) (3.12) (3.02) (3.30) (5.89) (1.14) (4.37) (5.08) (4.45) (1.14) (1.88) (6.27) (2.49) (2.29) (0.10) (6.76) (.25) (1.14) (2.08) (6.45) (2.03) (1.14) (2.08) FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 44
50 s (Insert arrangement 15-35) (5.36) (4.06) (2.29) (0.10) (3.12) (5.51) (1.14) (1.88) (1.14) (6.65) (0.00) (0.10) (1.14) (4.37) Shell size Arrangement no. (Applicable to MIL-DTL only) Number of Size Service rating location Supersedes D M All MS FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 45
51 s (Insert arrangement 15-37) (1.14) (6.65) (3.12) (3.02) (3.12) (5.51) (4.32) (1.02) (5.36) (4.06) (4.32) (1.27) (6.45) (2.03) (3.12) (3.23) (6.76) (0.25) (1.14) (4.37) (6.27) (2.49) (1.14) (4.37) (5.08) (4.45) (3.12) (3.23) (3.30) (5.89) (4.32) (1.27) (1.14) (6.65) (4.32) (1.02) (1.14) (6.65) (3.12) (3.02) (3.30) (5.89) (1.14) (4.37) (5.08) (4.45) (1.14) (1.88) (6.27) (2.49) (2.29) (0.10) (6.76) (0.25) (1.14) (2.08) (6.45) (2.03) (1.14) (2.08) FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 46
52 s (Insert arrangement 15-37) position (5.36) (4.06) (2.29) (0.10) (3.12) (5.51) (1.14) (1.88) (1.14) (6.65) (0.00) (0.10) (1.14) (4.37) Shell size Arrangement no. (Inactive for new design for MIL-DTL-38999) Number of Size Service rating location Supersedes M M All MS FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 47
53 s (Insert arrangement 15-97) position A (1.65) (5.94) G (5.26) (2.41) B (4.52) (4.52) H (5.94) (1.65) C (5.84) (0.58) J (4.52) (4.52) D (4.52) (4.52) K (1.65) (5.94) E (1.65) (5.94) L (1.19) (2.06) F (2.26) (5.97) M (1.19) (2.06) Shell size Arrangement no Number of Size Service rating location C, G, L, M 4 16 I 8 20 All others Supersedes MS FIGURE 4. Insert arrangement, electrical connector, shell size 15 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 48
54 s (Insert arrangement 17-2) (1.17) (8.26) (3.38) (7.59) (3.38) (7.59) (1.17) (8.26) (5.36) (6.38) (1.17) (5.87) (6.91) (4.65) (3.28) (5.00) (7.92) (2.57) (4.93) (3.38) (8.33) (0.28) (5.84) (1.27) (8.08) (2.01) (5.89) (1.02) (7.21) (4.17) (5.08) (3.18) (5.79) (5.99) (3.48) (4.85) (3.91) (7.34) (1.40) (5.82) (1.73) (8.15) (1.40) (5.82) (1.73) (8.15) (3.48) (4.85) (3.91) (7.34) (5.08) (3.18) (5.79) (5.99) (5.89) (1.02) (7.21) (4.17) (5.84) (1.27) (8.08) (2.01) (4.93) (3.38) FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 49
55 Shell size MIL-STD-1560C s (Insert arrangement 17-2) (8.33) (0.28) (3.28) (5.00) (7.92) (2.57) (1.17) (5.87) (6.91) (4.65) (0.00) (0.00) (5.36) (6.38) (Inactive for new design for MIL-DTL For new design, use arrangement no ) Arrangement no Number of Size Service rating position Pin Standard contact Socket 38 22D M All other M39029/ M39029/ (See note) Twinax 39 M39029/ M39029/ NOTE: To meet environmental sealing requirements, size 8 shielded used with this insert arrangement may require separate, non-standard sealing boots that are furnished with the connector. For this insert arrangement, some connector grommet designs use a heat shrink sleeve only with the size 8 shielded to meet environmental sealing requirements. Heat shrink sleeves have a maximum temperature rating of 175 C maximum. When heat shrink sleeves are used, connectors rated to 200 C max are derated to 175 C max. When heat shrink sleeves are used, sealing boots are not used, and when sealing boots are used, heat shrink sleeves are not used. FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 50
56 (INSERT ARRANGEMENT PATTERN ENTICAL TO 17-2, EXCEPT 17-3 USES SEALING BOOT IN ACCORDANCE WITH MIL-DTL-38999/62) s (Insert arrangement 17-3) (1.17) (8.26) (3.38) (7.59) (3.38) (7.59) (1.17) (8.26) (5.36) (6.38) (1.17) (5.87) (6.91) (4.65) (3.28) (5.00) (7.92) (2.57) (4.93) (3.38) (8.33) (0.28) (5.84) (1.27) (8.08) (2.01) (5.89) (1.02) (7.21) (4.17) (5.08) (3.18) (5.79) (5.99) (3.48) (4.85) (3.91) (7.34) (1.40) (5.82) (1.73) (8.15) (1.40) (5.82) (1.73) (8.15) (3.48) (4.85) (3.91) (7.34) (5.08) (3.18) (5.79) (5.99) (5.89) (1.02) (7.21) (4.17) (5.84) (1.27) (8.08) (2.01) (4.93) (3.38) FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 51
57 s (Insert arrangement 17-3) (8.33) (0.28) (3.28) (5.00) (7.92) (2.57) (1.17) (5.87) (6.91) (4.65) (0.00) (0.00) (5.36) (6.38) Shell size Arrangement no Number of Size Service rating position Pin Standard contact Socket 38 22D M All other M39029/ M39029/ M39029/113- M39029/114-1 Twinax 39 (See note) NOTE: For this insert arrangement, sealing boots in accordance with MIL-DTL-38999/62 shall be used to environmentally seal size 8 twinax. Heat shrink sleeves are not used when sealing boots are used. FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 52
58 + Y - X + X -Y s (Insert arrangement 17-6) A (3.07) (5.31) B (6.12) (0.00) C (0.00) (6.12) D (6.12) (0.00) E (3.07) (5.31) F (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600). 53
59 + Y - X + X -Y s (Insert arrangement 17-8) A (0.00) (5.99) B (3.25) (2.18) C (5.84) (1.98) D (2.39) (5.49) E (2.39) (5.49) F (5.84) (1.98) G (3.25) (2.18) H (0.00) (1.32) Shell size Arrangement no. Number of Size Service rating location Supersedes II All MS FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 54
60 s (Insert arrangement 17-11) position A (0.00) (7.37) G (4.83) (5.05) B (5.08) (2.54) H (6.99) (2.24) C (6.99) (2.24) J (5.08) (2.54) D (4.83) (5.05) K (0.00) (3.81) E (1.80) (7.16) L (0.00) (1.91) F (1.80) (7.16) Shell size Arrangement no Number of Size Service rating position 1 12 Coax J Standard Pin M39029/ Socket M39029/ Twinax B, L N A, C, D,E, F,G, H, K M39029/ M39029/ (For twinax part numbers and , see DLA Land and Maritime drawings and ) FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 55
61 s (Insert arrangement 17-23) position (1.02) (8.83) (2.04) (0.00) (1.02) (8.83) (4.08) (0.00) (4.08) (7.07) (6.12) (0.00) (2.04) (7.07) (8.16) (0.00) (0.00) (7.07) (7.14) (1.77) (2.04) (7.07) (5.10) (1.77) (4.08) (7.07) (3.06) (1.77) (7.14) (5.30) (1.02) (1.77) (5.10) (5.30) (1.02) (1.77) (3.06) (5.30) (3.06) (1.77) FIGURE 5. Insert arrangement, electrical connector, shell size 17 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 56
62 s (Insert arrangement 17-23) position (1.02) (5.30) (5.10) (1.77) (1.02) (5.30) (7.14) (1.77) (3.06) (5.30) (8.16) (3.53) (5.10) (5.30) (6.12) (3.53) (7.14) (5.30) (4.08) (3.53) (8.16) (3.53) (2.04) (3.53) (6.12) (3.53) (0.00) (3.53) (4.08) (3.53) (2.04) (3.53) (2.04) (3.53) (4.08) (3.53) (0.00) (3.53) (6.12) (3.53) (2.04) (3.53) (8.16) (3.53) (4.08) (3.53) (7.14) (5.30) (6.12) (3.53) (5.10) (5.30) (8.16) (3.53) (3.06) (5.30) (7.14) (1.77) (1.02) (5.30) (5.10) (1.77) (1.02) (5.30) (3.06) (1.77) (3.06) (5.30) (1.02) (1.77) (5.10) (5.30) (1.02) (1.77) (7.14) (5.30) (3.06) (1.77) (4.08) (7.07) (5.10) (1.77) (2.04) (7.07) (7.14) (1.77) (0.00) (7.07) (8.16) (0.00) (2.04) (7.07) (6.12) (0.00) (4.08) (7.07) (4.08) (0.00) (1.02) (8.83) (2.04) (0.00) (1.02) (8.83) (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location N All Standard contact Pin Socket M39029/ M39029/ FIGURE 5. Insert arrangement, electrical connector, shell size 17 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 57
63 s (Insert arrangement 17-26) location location A (0.00) (8.15) P (6.07) (5.44) B (3.33) (7.44) R (3.33) (7.44) C (6.07) (5.44) S (1.78) (4.50) D (7.75) (2.51) T (1.78) (4.50) E (8.10) (0.86) U (4.45) (2.39) F (7.06) (4.09) V (4.52) (0.91) G (4.80) (6.60) W (3.02) (3.84) H (1.70) (7.98) X (0.00) (5.16) J (1.70) (7.98) Y (3.02) (3.84) K (4.80) (6.60) Z (4.52) (0.91) L (7.06) (4.09) a (4.45) (2.39) M (8.10) (0.86) b (0.00) (1.65) N (7.75) (2.51) c (0.00) (1.65) Shell size Arrangement no. Number of Size Service rating Supersedes I All MS FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 58
64 + Y + X position s (Insert arrangement 17-35) (7.92) (2.18) (0.00) (2.39) (7.92) (0.10) (0.00) (4.67) (7.92) (2.39) (0.00) (6.96) (6.15) (5.61) (2.26) (8.03) (5.94) (3.33) (1.98) (5.61) (5.94) (1.04) (1.98) (3.33) (5.94) (1.24) (1.98) (1.04) (5.94) (3.53) (1.98) (1.24) (5.94) (5.82) (1.98) (3.53) (4.37) (7.09) (1.98) (5.82) (3.96) (4.47) (1.98) (8.10) (3.96) (2.18) (4.37) (7.09) (3.96) (0.10) (3.96) (4.47) (3.96) (2.39) (3.96) (2.18) (3.96) (4.67) (3.96) (0.10) (3.96) (6.96) (3.96) (2.39) (2.26) (8.03) (3.96) (4.67) (1.98) (5.61) (3.96) (6.96) FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600)
65 position s (Insert arrangement 17-35) (1.98) (3.33) (6.15) (5.61) (1.98) (1.04) (5.94) (3.33) (1.98) (1.24) (5.94) (1.04) (1.98) (3.53) (5.94) (1.24) (1.98) (5.82) (5.94) (3.53) (1.98) (8.10) (5.94) (5.82) (0.00) (8.36) (7.92) (2.18) (0.00) (4.47) (7.92) (0.10) (0.00) (2.18) (7.92) (2.39) (0.00) (0.10) Shell size Arrangement no. Number of Size Service rating location Supersedes D M All MS FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 60
66 + Y - X + X position s (Insert arrangement 17-55) (7.92) (2.18) (0.00) (2.39) (7.92) (0.10) (0.00) (4.67) (7.92) (2.39) (0.00) (6.96) (6.15) (5.61) (2.26) (8.03) (5.94) (3.33) (1.98) (5.61) (5.94) (1.04) (1.98) (3.33) (5.94) (1.24) (1.98) (1.04) (5.94) (3.53) (1.98) (1.24) (5.94) (5.82) (1.98) (3.53) (4.37) (7.09) (1.98) (5.82) (3.96) (4.47) (1.98) (8.10) (3.96) (2.18) (4.37) (7.09) (3.96) (0.10) (3.96) (4.47) (3.96) (2.39) (3.96) (2.18) (3.96) (4.67) (3.96) (0.10) (3.96) (6.96) (3.96) (2.39) (2.26) (8.03) (3.96) (4.67) (1.98) (5.61) (3.96) (6.96) - Y FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 61
67 position (Inactive for new design) s (Insert arrangement 17-55) (1.98) (3.33) (6.15) (5.61) (1.98) (1.04) (5.94) (3.33) (1.98) (1.24) (5.94) (1.04) (1.98) (3.53) (5.94) (1.24) (1.98) (5.82) (5.94) (3.53) (1.98) (8.10) (5.94) (5.82) (0.00) (8.36) (7.92) (2.18) (0.00) (4.47) (7.92) (0.10) (0.00) (2.18) (7.92) (2.39) (0.00) (0.10) Shell size Arrangement no. Number of Size Service rating location Supersedes M M All MS FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 62
68 s (Insert arrangement 17-99) location location A.000 (0.00) (8.15) N (7.75) (2.51) B (3.33) (7.44) P (6.07) (5.44) C (6.07) (5.44) R (3.33) (7.44) D (7.75) (2.51) S (1.78) (4.50) E (8.10) (0.86) T (1.78) (4.50) F (7.06) (4.09) U (4.45) (2.39) G (4.80) (6.60) V (3.81) (1.91) H (1.70) (7.98) W (0.00) (4.09) J (1.70) (7.98) X (3.81) (1.91) K (4.80) (6.60) Y (4.45) (2.39) L (7.06) (4.09) Z (0.00) (0.64) M (8.10) (0.86) Shell size Arrangement no Number of Size Service rating W, Z 2 16 I All others Supersedes MS FIGURE 5. Insert arrangement, electrical connector, shell size 17 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 63
69 s (Insert arrangement 19-11) position A (2.67) (6.60) G (6.99) (1.35) B (6.35) (3.35) H (6.35) (3.35) C (6.99) (1.35) J (2.67) (6.60) D (4.55) (5.46) K (0.00) (2.67) E (0.00) (7.14) L (0.00) (2.34) F (4.55) (5.46) Shell size Arrangement no. Number of Size Service rating location II All Supersedes MS FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600). 64
70 Shell size (Inactive for new design for MIL-DTL For new design, use arrangement no ) s (Insert arrangement 19-18) position A (1.73) (9.65) K (4.57) (4.57) B (4.57) (4.57) L (9.58) (1.65) C (9.58) (1.65) M (8.05) (0.00) D (8.05) (0.00) N (9.58) (1.65) E (9.58) (1.65) P (4.57) (4.57) F (4.57) (4.57) R (1.73) (9.65) G (1.73) (9.65) S (0.00) (8.10) H (0.00) (8.10) T (0.00) (1.12) J (1.73) (9.65) U (0.00) (1.12) Arrangement No. Number of Size Service rating location Standard contact Pin Socket 8 4 Twinax B, F, K, P M39029/ M39029/ (see note) 14 22D M All others M39029/58 M39029/56 NOTE: To meet environmental sealing requirements, size 8 shielded used with this insert arrangement may require separate, non-standard sealing boots that are furnished with the connector. For this insert arrangement, some connector grommet designs use a heat shrink sleeve only with the size 8 shielded to meet environmental sealing requirements. Heat shrink sleeves have a maximum temperature rating of 175 C maximum. When heat shrink sleeves are used, connectors rated to 200 C max are derated to 175 C max. When heat shrink sleeves are used, sealing boots are not used, and when sealing boots are used, heat shrink sleeves are not used. FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 65
71 Shell size (INSERT ARRANGEMENT PATTERN ENTICAL TO 19-18, EXCEPT USES SEALING BOOT IN ACCORDANCE WITH MIL-DTL-38999/62) s (Insert arrangement 19-19) position A (1.73) (9.65) K (4.57) (4.57) B (4.57) (4.57) L (9.58) (1.65) C (9.58) (1.65) M (8.05) (0.00) D (8.05) (0.00) N (9.58) (1.65) E (9.58) (1.65) P (4.57) (4.57) F (4.57) (4.57) R (1.73) (9.65) G (1.73) (9.65) S (0.00) (8.10) H (0.00) (8.10) T (0.00) (1.12) J (1.73) (9.65) U (0.00) (1.12) Arrangement no Number of 4 Size 8 (see note) Service rating Twinax 14 22D M location B,F,K,P All others Pin SAE-AS39029 / SAE-AS39029 /58 Standard contact Socket SAE-AS39029 / SAE-AS39029 /56 NOTE: For this insert arrangement, sealing boots in accordance with MIL-DTL-38999/62 shall be used to environmentally seal size 8 twinax. Heat shrink sleeves are not used when sealing boots are used. FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 66
72 s (Insert arrangement 19-23) position position (0.00) (9.99) (3.97) (6.88) (2.08) (9.77) (5.62) (5.62) (4.06) (9.12) (6.88) (3.97) (5.87) (8.08) (7.67) (2.06) (7.42) (6.68) (7.95) (0.00) (8.65) (4.99) (7.67) (2.06) (9.50) (3.09) (6.88) (3.97) (9.93) (1.04) (5.62) (5.62) FIGURE 6. Insert arrangement, electrical connector, shell size 19 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 67
73 s (Insert arrangement 19-23) position position (9.93) (1.04) (3.97) (6.88) (9.50) (3.09) (2.06) (7.67) (8.65) (4.99) (0.00) (5.91) (7.42) (6.68) (2.02) (5.55) (5.87) (8.08) (3.80) (4.52) (4.06) (9.12) (5.11) (2.95) (2.08) (9.77) (5.82) (1.03) (0.00) (9.99) (5.82) (1.03) (2.08) (9.77) (5.11) (2.95) (4.06) (9.12) (3.80) (4.52) (5.87) (8.08) (2.02) (5.55) (7.42) (6.68) (0.00) (5.91) (8.65) (4.99) (2.02) (5.55) (9.50) (3.09) (3.80) (4.52) (9.93) (1.04) (5.11) (2.95) (9.93) (1.04) (5.82) (1.03) (9.50) (3.09) (5.82) (1.03) (8.65) (4.99) (5.11) (2.95) (7.42) (6.68) (3.80) (4.52) (5.87) (8.08) (2.02) (5.55) (4.06) (9.12) (0.00) (3.87) (2.08) (9.77) (2.09) (3.25) (0.00) (7.95) (3.52) (1.61) (2.06) (7.67) (3.83) (0.55) (3.97) (6.88) (2.92) (2.53) (5.62) (5.62) (1.09) (3.71) (6.88) (3.97) (1.09) (3.71) FIGURE 6. Insert arrangement, electrical connector, shell size 19 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 68
74 s (Insert arrangement 19-23) position position (7.67) (2.06) (2.92) (2.53) (7.95) (0.00) (3.83) (0.55) (7.67) (2.06) (3.52) (1.61) (6.88) (3.97) (2.09) (3.25) (5.62) (5.62) (0.00) (1.83) (3.97) (6.88) (1.74) (0.56) (2.06) (7.67) (1.09) (1.48) (0.00) (7.95) (1.09) (1.48) (2.06) (7.67) (1.74) (0.56) Shell size Arrangement no. Number of Size Service rating location N All Standard contact Pin Socket M39029/ M39029/ FIGURE 6. Insert arrangement, electrical connector, shell size 19 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 69
75 position Shell size location s (Insert arrangement 19-28) location A (1.68) (8.97) R (7.26) (5.51) B (4.80) (7.75) S (4.80) (7.75) C (7.26) (5.51) T (1.68) (8.97) D (8.76) (2.49) U (0.00) (5.84) E (9.07) (0.84) V (3.15) (4.90) F (8.15) (4.06) W (5.31) (2.41) G (6.15) (6.73) X (5.79) (0.84) H (3.30) (8.51) Y (4.42) (3.84) J (0.00) (9.12) Z (0.00) (4.85) K (3.30) (8.51) a (4.42) (3.84) L (6.15) (6.73) b (5.79) (0.84) M (8.15) (4.06) c (5.31) (2.41) N (9.07) (0.84) d (3.15) (4.90) P (8.76) (2.49) e (0.00) (1.57) Arrangement no Number of Size Service rating location Supersedes 2 16 e, Z MS I All others 28 FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 70
76 + Y - X + X s (Insert arrangement 19-30) location location position A (1.65) (8.79) S (1.65) (8.79) B (4.72) (7.59) T (2.13) (5.51) C (7.16) (5.33) U (4.60) (3.28) D (8.64) (2.36) V (5.79) (0.20) E (8.92) (0.84) W (4.90) (2.97) F (8.00) (4.01) X (2.44) (5.16) G (5.99) (6.63) Y (0.00) (7.37) H (3.15) (8.38) Z (2.44) (5.16) J (3.15) (8.38) a (4.90) (2.97) K (5.99) (6.63) b (5.79) (0.20) L (8.00) (4.01) c (4.60) (3.28) M (8.92) (0.84) d (2.13) (5.51) N (8.64) (2.36) e (0.00) (1.83) P (7.16) (5.33) f (1.75) (1.93) R (4.72) (7.59) g (1.75) (1.93) Shell size Arrangement no Number of Size Service rating location 1 16 e I All others FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) - Y Supersedes MS
77 location s (Insert arrangement 19-32) location A (1.68) (8.97) T (1.68) (8.97) B (4.80) (7.75) U (0.00) (5.84) C (7.26) (5.51) V (3.15) (4.90) D (8.76) (2.49) W (5.31) (2.41) E (9.07) (0.84) X (5.79) (0.84) F (8.15) (4.06) Y (4.42) (3.84) G (6.15) (6.73) Z (1.65) (5.61) H (3.30) (8.51) a (1.65) (5.61) J (0.00) (9.12) b (4.42) (3.84) K (3.30) (8.51) c (5.79) (0.84) L (6.15) (6.73) d (5.31) (2.41) M (8.15) (4.06) e (3.15) (4.90) N (9.07) (0.84) f (0.00) (2.44) P (8.76) (2.49) g (2.44) (0.00) R (7.26) (5.51) h (0.00) (2.44) S (4.80) (7.75) j (2.44) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of 32 MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 72
78 position s (Insert arrangement 19-35) (9.07) (2.29) (1.14) (9.14) (9.07) (0.00) (1.14) (6.86) (9.07) (2.29) (1.14) (4.57) (7.09) (5.72) (1.14) (2.29) (7.09) (3.43) (1.14) (0.00) (7.09) (1.14) (1.14) (2.29) (7.09) (1.14) (1.14) (4.57) (7.09) (3.43) (1.14) (6.86) (7.09) (5.72) (1.14) (9.14) (5.11) (6.86) (3.12) (8.00) (5.11) (4.57) (3.12) (5.72) (5.11) (2.29) (3.12) (3.43) (5.11) (0.00) (3.12) (1.14) (5.11) (2.29) (3.12) (1.14) (5.11) (4.57) (3.12) (3.43) (5.11) (6.86) (3.12) (5.72) (3.12) (8.00) (3.12) (8.00) FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 73
79 position MIL-STD-1560C s (Insert arrangement 19-35) (3.12) (5.72) (5.11) (6.86) (3.12) (3.43) (5.11) (4.57) (3.12) (1.14) (5.11) (2.29) (3.12) (1.14) (5.11) (0.00) (3.12) (3.43) (5.11) (2.29) (3.12) (5.72) (5.11) (4.57) (3.12) (8.00) (5.11) (6.86) (1.14) (9.14) (7.09) (5.72) (1.14) (6.86) (7.09) (3.43) (1.14) (4.57) (7.09) (1.14) (1.14) (2.29) (7.09) (1.14) (1.14) (0.00) (7.09) (3.43) (1.14) (2.29) (7.09) (5.72) (1.14) (4.57) (9.07) (2.29) (1.14) (6.86) (9.07) (0.00) (1.14) (9.14) (9.07) (2.29) Shell size Arrangement no. (Applicable to MIL-DTL only) Number of Size Service rating location Supersedes D M All MS FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 74
80 position s (Insert arrangement 19-45) (9.07) (2.06) (2.24) (9.14) (9.07) (0.23) (1.14) (6.63) (9.07) (2.51) (1.14) (4.34) (7.72) (5.41) (1.14) (2.06) (7.09) (3.20) (1.14) (.23) (7.09) (0.91) (1.14) (2.51) (7.09) (1.37) (1.14) (4.80) (7.09) (3.66) (1.14) (7.09) (7.09) (5.94) (1.14) (9.37) (6.20) (7.11) (3.96) (7.65) (5.11) (4.34) (3.12) (5.49) (5.11) (2.06) (3.12) (3.20) (5.11) (0.23) (3.12) (0.91) (5.11) (2.51) (3.12) (1.37) (5.11) (4.80) (3.12) (3.66) (5.11) (7.09) (3.12) (5.94) (3.96) (7.65) (3.12) (8.23) FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 75
81 position s (Insert arrangement 19-45) (3.12) (5.49) (6.20) (7.11) (3.12) (3.20) (5.11) (4.34) (3.12) (0.91) (5.11) (2.06) (3.12) (1.37) (5.11) (0.23) (3.12) (3.66) (5.11) (2.51) (3.12) (5.94) (5.11) (4.80) (3.12) (8.23) (5.11) (7.09) (2.24) (9.14) (7.72) (5.41) (0.00) (8.61) (7.09) (3.20) (1.14) (6.63) (7.09) (0.91) (1.14) (4.34) (7.09) (1.37) (1.14) (2.06) (7.09) (3.66) (1.14) (0.23) (7.09) (5.94) (1.14) (2.51) (9.07) (2.06) (1.14) (4.80) (9.07) (0.23) (1.14) (7.09) (9.07) (2.51) (1.14) (9.37) Shell size Arrangement no. (Applicable to MIL-DTL-38999) Number of Size Service rating location Supersedes D M All MS FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 76
82 position s (Insert arrangement 19-66) (9.07) (2.29) (1.14) (9.14) (9.07) (0.00) (1.14) (6.86) (9.07) (2.29) (1.14) (4.57) (7.09) (5.72) (1.14) (2.29) (7.09) (3.43) (1.14) (0.00) (7.09) (1.14) (1.14) (2.29) (7.09) (1.14) (1.14) (4.57) (7.09) (3.43) (1.14) (6.86) (7.09) (5.72) (1.14) (9.14) (5.11) (6.86) (3.12) (8.00) (5.11) (4.57) (3.12) (5.72) (5.11) (2.29) (3.12) (3.43) (5.11) (0.00) (3.12) (1.14) (5.11) (2.29) (3.12) (1.14) (5.11) (4.57) (3.12) (3.43) (5.11) (6.86) (3.12) (5.72) (3.12) (8.00) (3.12) (8.00) FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 77
83 position s (Insert arrangement 19-66) (3.12) (5.72) (5.11) (6.86) (3.12) (3.43) (5.11) (4.57) (3.12) (1.14) (5.11) (2.29) (3.12) (1.14) (5.11) (0.00) (3.12) (3.43) (5.11) (2.29) (3.12) (5.72) (5.11) (4.57) (3.12) (8.00) (5.11) (6.86) (1.14) (9.14) (7.09) (5.72) (1.14) (6.86) (7.09) (3.43) (1.14) (4.57) (7.09) (1.14) (1.14) (2.29) (7.09) (1.14) (1.14) (0.00) (7.09) (3.43) (1.14) (2.29) (7.09) (5.72) (1.14) (4.57) (9.07) (2.29) (1.14) (6.86) (9.07) (0.00) (1.14) (9.14) (9.07) (2.29) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 78
84 position s (Insert arrangement 19-67) (9.07) (2.06) (2.24) (9.14) (9.07) (0.23) (1.14) (6.63) (9.07) (2.51) (1.14) (4.34) (7.72) (5.41) (1.14) (2.06) (7.09) (3.20) (1.14) (0.23) (7.09) (0.91) (1.14) (2.51) (7.09) (1.37) (1.14) (4.80) (7.09) (3.66) (1.14) (7.09) (7.09) (5.94) (1.14) (9.37) (6.20) (7.11) (3.96) (7.65) (5.11) (4.34) (3.12) (5.49) (5.11) (2.06) (3.12) (3.20) (5.11) (0.23) (3.12) (0.91) (5.11) (2.51) (3.12) (1.37) (5.11) (4.80) (3.12) (3.66) (5.11) (7.09) (3.12) (5.94) (3.96) (7.65) (3.12) (8.23) FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 79
85 position MIL-STD-1560C s (Insert arrangement 19-67) (3.12) (5.49) (6.20) (7.11) (3.12) (3.20) (5.11) (4.34) (3.12) (0.91) (5.11) (2.06) (3.12) (1.37) (5.11) (.23) (3.12) (3.66) (5.11) (2.51) (3.12) (5.94) (5.11) (4.80) (3.12) (8.23) (5.11) (7.09) (2.24) (9.14) (7.72) (5.41) (0.00) (8.61) (7.09) (3.20) (1.14) (6.63) (7.09) (0.91) (1.14) (4.34) (7.09) (1.37) (1.14) (2.06) (7.09) (3.66) (1.14) (0.23) (7.09) (5.94) (1.14) (2.51) (9.07) (2.06) (1.14) (4.80) (9.07) (0.23) (1.14) (7.09) (9.07) (2.51) (1.14) (9.37) Shell size Arrangement no. (Inactive for new design for MIL-DTL-38999) Number of Size Service rating location Supersedes M M All MS FIGURE 6. Insert arrangement, electrical connector, shell size 19 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 80
86 position s (Insert arrangement 21-1) (1.35) (10.82) (2.49) (8.18) (3.71) (10.26) (4.67) (7.11) (5.89) (9.19) (6.55) (5.59) (7.77) (7.67) (7.90) (3.58) (9.27) (5.77) (8.43) (1.22) (10.31) (3.58) (8.43) (1.22) (10.85) (1.22) (7.90) (3.58) (10.85) (1.22) (6.55) (5.59) (10.31) (3.58) (4.67) (7.11) (9.27) (5.77) (2.49) (8.18) (7.77) (7.67) (1.22) (6.12) (5.89) (9.19) (1.22) (6.12) (3.71) (10.26) (3.40) (5.05) (1.35) (10.82) (5.28) (3.53) (1.35) (10.82) (6.02) (1.22) (3.71) (10.26) (6.02) (1.22) (5.89) (9.19) (5.28) (3.53) (7.77) (7.67) (3.40) (5.05) FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 81
87 position s (Insert arrangement 21-1) (9.27) (5.77) (1.22) (6.12) (10.31) (3.58) (1.22) (6.12) (10.85) (1.22) (3.40) (5.05) (10.85) (1.22) (5.28) (3.53) (10.31) (3.58) (6.02) (1.22) (9.27) (5.77) (6.02) (1.22) (7.77) (7.67) (5.28) (3.53) (5.89) (9.19) (3.40) (5.05) (3.71) (10.26) (1.22) (3.71) (1.35) (10.82) (1.22) (3.71) (0.00) (8.20) (3.18) (2.29) (2.49) (8.18) (3.94) (0.00) (4.67) (7.11) (3.18) (2.29) (6.55) (5.59) (1.22) (3.71) (7.90) (3.58) (1.22) (3.71) (8.43) (1.22) (3.18) (2.29) (8.43) (1.22) (3.94) (0.00) (7.90) (3.58) (3.18) (2.29) (6.55) (5.59) (0.00) (1.35) (4.67) (7.11) (1.22) (0.74) (2.49) (8.18) (1.22) (0.74) (0.00) (8.81) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M 79 MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 82
88 + Y - X + X - Y s (Insert arrangement 21-11) position A (3.07) (8.43) G (8.84) (1.55) B (7.77) (4.50) H (7.77) (4.50) C (8.84) (1.55) J (3.07) (8.43) D (5.77) (6.86) K (0.00) (3.12) E (0.00) (8.97) L (0.00) (2.92) F (5.77) (6.86) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 83
89 s (Insert arrangement 21-16) position A (3.00) (8.18) J (8.66) (0.91) B (6.88) (5.36) K (6.88) (5.36) C (8.66) (0.91) L (3.00) (8.18) D (7.82) (3.81) M (0.00) (4.45) E (4.62) (7.37) N (3.91) (1.57) F (0.00) (8.71) P (2.39) (3.10) G (4.62) (7.37) R (2.39) (3.10) H (7.82) (3.81) S (3.91) (1.57) Shell size Arrangement no. Number of Size Service rating location Supersedes II All MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 84
90 position s (Insert arrangement (4.08) (10.60) (2.04) (0.00) (2.04) (10.60) (4.08) (0.00) (0.00) (10.60) (6.12) (0.00) (2.04) (10.60) (8.16) (0.00) (4.08) (10.60) (10.20) (0.00) (7.14) (8.83) (11.22) (1.77) FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 85
91 s (Insert arrangement 21-23) position (5.10) (8.83) (9.18) (1.77) (3.06) (8.83) (7.14) (1.77) (1.02) (8.83) (5.10) (1.77) (1.02) (8.83) (3.06) (1.77) (3.06) (8.83) (1.02) (1.77) (5.10) (8.83) (1.02) (1.77) (7.14) (8.83) (3.06) (1.77) (8.16) (7.07) (5.10) (1.77) (6.12) (7.07) (7.14) (1.77) (4.08) (7.07) (9.18) (1.77) (2.04) (7.07) (11.22) (1.77) (0.00) (7.07) (10.20) (3.53) (2.04) (7.07) (8.16) (3.53) (4.08) (7.07) (6.12) (3.53) (6.12) (7.07) (4.08) (3.53) (8.16) (7.07) (2.04) (3.53) (9.18) (5.30) (0.00) (3.53) (7.14) (5.30) (2.04) (3.53) (5.10) (5.30) (4.08) (3.53) (3.06) (5.30) (6.12) (3.53) (1.02) (5.30) (8.16) (3.53) (1.02) (5.30) (10.20) (3.53) (3.06) (5.30) (9.18) (5.30) (5.10) (5.30) (7.14) (5.30) (7.14) (5.30) (5.10) (5.30) (9.18) (5.30) (3.06) (5.30) (10.20) (3.53) (1.02) (5.30) (8.16) (3.53) (1.02) (5.30) (6.12) (3.53) (3.06) (5.30) (4.08) (3.53) (5.10) (5.30) FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 86
92 s (Insert arrangement 21-23) position (2.04) (3.53) (7.14) (5.30) (0.00) (3.53) (9.18) (5.30) (2.04) (3.53) (8.16) (7.07) (4.08) (3.53) (6.12) (7.07) (6.12) (3.53) (4.08) (7.07) (8.16) (3.53) (2.04) (7.07) (10.20) (3.53) (0.00) (7.07) (11.22) (1.77) (2.04) (7.07) (9.18) (1.77) (4.08) (7.07) (7.14) (1.77) (6.12) (7.07) (5.10) (1.77) (8.16) (7.07) (3.06) (1.77) (7.14) (8.83) (1.02) (1.77) (5.10) (8.83) (1.02) (1.77) (3.06) (8.83) (3.06) (1.77) (1.02) (8.83) (5.10) (1.77) (1.02) (8.83) (7.14) (1.77) (3.06) (8.83) (9.18) (1.77) (5.10) (8.83) (11.22) (1.77) (7.14) (8.83) (10.20) (0.00) (4.08) (10.60) (8.16) (0.00) (2.04) (10.60) (6.12) (0.00) (0.00) (10.60) (4.08) (0.00) (2.04) (10.60) (2.04) (0.00) (4.08) (10.60) (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location N All Standard contact Pin Socket M39029/ M39029/ FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 87
93 location s (Insert arrangement 21-24) position location A (4.45) (9.53) N (3.81) (5.08) B (8.89) (5.08) P (6.35) (0.00) C (10.16) (0.00) R (5.08) (3.81) D (8.89) (5.08) S (1.91) (6.35) E (5.08) (8.89) T (1.91) (6.35) F (0.00) (10.16) U (5.08) (3.81) G (5.08) (8.89) V (6.35) (0.00) H (8.89) (5.08) W (3.81) (5.08) J (10.16) (0.00) X (0.00) (3.81) K (8.89) (5.08) Y (2.54) (0.64) L (4.45) (9.53) Z (0.00) (2.54) M (0.00) (7.62) a (2.54) (0.64) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 88
94 s (Insert arrangement 21-25) location location position A (0.00) (10.16) P (5.72) (5.72) B (3.81) (9.53) R (3.81) (9.53) C (5.72) (5.72) S (1.91) (5.72) D (9.53) (4.45) T (6.35) (1.91) E (10.16) (0.64) U (3.81) (5.08) F (9.53) (3.18) V (3.81) (5.08) G (6.99) (7.62) W (6.35) (1.91) H (2.54) (10.16) X (1.91) (5.72) J (2.54) (10.16) Y (0.00) (1.91) K (6.99) (7.62) Z (3.18) (0.64) L (9.53) (3.18) a (0.00) (3.18) M (10.16) (0.64) b (3.18) (0.64) N (9.53) (4.45) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 89
95 position s (Insert arrangement 21-27) location location position A (0.00) (10.16) R (3.81) (9.53) B (3.81) (9.53) S (3.18) (5.72) C (6.99) (6.99) T (5.72) (2.54) D (9.53) (3.81) U (6.35) (1.27) E (10.16) (0.00) V (3.81) (5.08) F (9.53) (3.81) W (0.00) (6.35) G (6.99) (7.62) X (3.81) (5.08) H (2.54) (10.16) Y (6.35) (1.27) J (2.54) (10.16) Z (5.72) (2.54) K (6.99) (7.62) a (3.18) (5.72) L (9.53) (3.81) b (0.00) (2.54) M (10.16) (0.00) c (2.54) (0.64) N (9.53) (3.81) d (2.54) (0.64) P (6.99) (6.99) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 90
96 + Y + X position s (Insert arrangement 21-29) location location position (1.70) (10.46) (10.46) (1.52) (4.93) (9.45) (7.87) (3.71) (7.45) (7.14) (7.45) (7.14) (7.87) (3.71) (4.93) (9.45) (10.46) (1.52) (1.70) (10.46) (10.39) (1.88) (3.20) (5.08) (7.90) (4.29) (6.71) (0.08) (7.34) (7.67) (3.18) (5.26) (3.15) (10.08) (3.18) (5.26) (0.00) (8.81) (6.71) (0.08) (3.15) (10.08) (3.20) (5.08) (7.34) (7.67) (2.24) ) (7.90) (4.29) (2.24) (0.08) (10.39) (1.88) FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 91
97 Shell size Arrangement no Number of Size Service rating location , 22, 23, I 21, 24, 26, All others NOTES: 1. Trademark and shall appear in available space. identifying letter shall be located so as to identify relative contact. 2. The size 16 contact cavities are not located on the centerline of the arrangement. The size 16 contact cavities are positioned.003 below the centerline. FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 92
98 position s (Insert arrangement 21-35) (1.35) (10.82) (2.49) (8.18) (3.71) (10.26) (4.67) (7.11) (5.89) (9.19) (6.55) (5.59) (7.77) (7.67) (7.90) (3.58) (9.27) (5.77) (8.43) (1.22) (10.31) (3.58) (8.43) (1.22) (10.85) (1.22) (7.90) (3.58) (10.85) (1.22) (6.55) (5.59) (10.31) (3.58) (4.67) (7.11) (9.27) (5.77) (2.49) (8.18) (7.77) (7.67) (1.22) (6.12) (5.89) (9.19) (1.22) (6.12) (3.71) (10.26) (3.40) (5.05) (1.35) (10.82) (5.28) (3.53) (1.35) (10.82) (6.02) (1.22) (3.71) (10.26) (6.02) (1.22) (5.89) (9.19) (5.28) (3.53) FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 93
99 position MIL-STD-1560C s (Insert arrangement 21-35) (7.77) (7.67) (3.40) (5.05) (9.27) (5.77) (1.22) (6.12) (10.31) (3.58) (1.22) (6.12) (10.85) (1.22) (3.40) (5.05) (10.85) (1.22) (5.28) (3.53) (10.31) (3.58) (6.02) (1.22) (9.27) (5.77) (6.02) (1.22) (7.77) (7.67) (5.28) (3.53) (5.89) (9.19) (3.40) (5.05) (3.71) (10.26) (1.22) (3.71) (1.35) (10.82) (1.22) (3.71) (.00) (8.20) (3.18) (2.29) (2.49) (8.18) (3.94) (0.00) (4.67) (7.11) (3.18) (2.29) (6.55) (5.59) (1.22) (3.71) (7.90) (3.58) (1.22) (3.71) (8.43) (1.22) (3.18) (2.29) (8.43) (1.22) (3.94) (0.00) (7.90) (3.58) (3.18) (2.29) (6.55) (5.59) (0.00) (1.35) (4.67) (7.11) (1.22) (0.74) (2.49) (8.18) (1.22) (0.74) (0.00) (8.81) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M ALL MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 94
100 position s (Insert arrangement 21-39) A (1.65) (10.44) X (0.00) (7.49) B (4.80) (9.42) Y (3.20) (6.50) C (7.47) (7.47) Z (5.89) (4.55) D (9.42) (4.80) a (7.11) (1.45) E (10.44) (1.65) b (7.11) (1.88) F (10.44) (1.65) c (5.51) (4.80) G (9.42) (4.80) d (2.84) (6.73) H (7.47) (7.47) e (2.84) (6.73) J (4.80) (9.42) f (5.51) (4.80) K (1.65) (10.44) g (7.11) (1.88) L (1.65) (10.44) h (7.11) (1.45) M (4.80) (9.42) i (5.89) (4.55) N (7.47) (7.47) j (3.20) (6.50) P (9.42) (4.80) k (0.00) (4.17) R (10.44) (1.65) m (2.90) (1.22) FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 95
101 position MIL-STD-1560C s (Insert arrangement 21-39) S (10.44) (1.65) n (2.69) (2.72) T (9.42) (4.80) p (0.00) (4.80) U (7.47) (7.47) q (2.69) (2.72) V (4.80) (9.42) r (2.90) (1.09) W (1.65) (10.44) Shell size Arrangement no Number of Size Service rating location 2 16 r, m I All others Supersedes MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 96
102 + Y + X Shell size Arrangement no. Number of Insert arrangement Size Service rating location Supersedes I All MS FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 97
103 (Inactive for new design for MIL-DTL For new design, use arrangement no ) s (Insert arrangement 21-75) X axis Y axis A (4.57) (4.57) B (4.57) (4.57) C (4.57) (4.57) D (4.57) (4.57) Shell size Arrangement no. Number of Size 8 (see note) Service rating location Standard contact Pin Socket Twinax All M39029/ M39029/ NOTE: To meet environmental sealing requirements, size 8 shielded used with this insert arrangement may require separate, non-standard sealing boots that are furnished with the connector. For this insert arrangement, some connector grommet designs use a heat shrink sleeve only with the size 8 shielded to meet environmental sealing requirements. When heat shrink sleeves are used, sealing boots are not used, and when sealing boots are used, heat shrink sleeves are not used. Heat shrink sleeves have a maximum temperature rating of 175 C maximum. When heat shrink sleeves are used, connectors rated to 200 C max are derated to 175 C max. FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 98
104 (INSERT ARRANGEMENT PATTERN ENTICAL TO 21-75, EXCEPT USES SEALING BOOTS IN ACCORDANCE WITH MIL-DTL-38999/62) s (Insert arrangement 21-76) X axis Y axis A (4.57) (4.57) B (4.57) (4.57) C (4.57) (4.57) D (4.57) (4.57) Shell size Arrangement No. Number of Size 8 (see note) Service rating location Standard contact Pin Socket Twinax All M39029/ M39029/ NOTE: For this insert arrangement, sealing boots in accordance with MIL-DTL-38999/62 shall be used to environmentally seal size 8 twinax. Heat shrink sleeves are not used with size 8 twinax when sealing boots are used. FIGURE 7. Insert arrangement, electrical connector, shell size 21 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 99
105 position s (Insert arrangement 23-1) (10.87) (6.12) (0.00) (1.19) (11.86) (3.91) (0.00) (3.61) (12.40) (1.55) (0.00) (6.02) (10.54) (0.00) (0.00) (8.43) (12.40) (1.55) (0.00) (10.85) (10.87) (3.61) (2.11) (12.07) (10.87) (6.02) (2.11) (9.65) (8.43) (8.46) (2.11) (7.24) (8.43) (6.05) (2.11) (4.83) (8.43) (3.63) (2.11) (2.41) (8.43) (1.22) (2.11) (0.00) (8.43) (1.19) (2.11) (2.41) (8.43) (3.61) (2.11) (4.83) (8.43) (6.02) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (6.32) (9.65) (2.11) (12.07) (6.32) (7.24) (4.22) (10.87) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600). 100
106 position s (Insert arrangement 23-1) (6.32) (4.83) (4.22) (8.46) (6.32) (2.41) (4.22) (6.05) (6.32) (0.00) (4.22) (3.63) (6.32) (2.41) (4.22) (1.22) (6.32) (4.83) (4.22) (1.19) (6.32) (7.24) (4.22) (3.61) (6.32) (9.65) (4.22) (6.02) (4.22) (10.87) (4.22) (8.43) (4.22) (8.46) (4.22) (10.85) (4.22) (6.05) (6.32) (9.65) (4.22) (3.63) (6.32) (7.24) (4.22) (1.22) (6.32) (4.83) (4.22) (1.19) (6.32) (2.41) (4.22) (3.61) (6.32) (0.00) (4.22) (6.02) (6.32) (2.41) (4.22) (8.43) (6.32) (4.83) (4.22) (10.85) (6.32) (7.24) (2.11) (12.07) (6.32) (9.65) (2.11) (9.65) (8.43) (8.46) (2.11) (7.24) (8.43) (6.05) (2.11) (4.83) (8.43) (3.63) (2.11) (2.41) (8.43) (1.22) (2.11) (0.00) (8.43) (1.19) (2.11) (2.41) (8.43) (3.61) (2.11) (4.83) (8.43) (6.02) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (10.87) (6.12) (2.11) (12.07) (11.86) (3.91) (0.00) (10.87) (12.40) (1.55) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 101
107 position Shell size Arrangement no. (Inactive for new design for MIL-DTL-38999) Number of s (Insert arrangement 23-1) Size Service rating location (0.00) (8.46) (10.54) (0.00) (0.00) (6.05) (12.40) (1.55) (0.00) (3.63) (10.87) (3.61) (0.00) (1.22) (10.87) (6.02) Supersedes M M All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 102
108 position s (Insert arrangement 23-2) (11.56) (4.04) (0.00) (2.69) (11.56) (1.35) (0.00) (5.38) (12.24) (1.35) (0.00) (8.08) (11.56) (4.04) (0.00) (10.77) (9.25) (8.08) (2.31) (12.12) (9.25) (5.38) (2.31) (9.42) (9.25) (2.69) (2.31) (6.73) (9.25) (0.00) (2.31) (4.04) (9.25) (2.69) (2.31) (1.35) (9.25) (5.38) (2.31) (1.35) (9.25) (8.08) (2.31) (4.04) (6.93) (9.42) (2.31) (6.73) (6.93) (6.73) (2.31) (9.42) (6.93) (4.04) (2.31) (12.12) (6.93) (1.35) (4.62) (10.77) (6.93) (1.35) (4.62) (8.08) (6.93) (4.04) (4.62) (5.38) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 103
109 position s (Insert arrangement 23-2) (6.93) (6.73) (4.62) (2.69) (7.29) (9.91) (4.62) (0.00) (4.62) (10.77) (4.62) (2.69) (4.62) (8.08) (4.62) (5.38) (4.62) (5.38) (4.62) (8.08) (4.62) (2.69) (4.88) (11.33) (4.62) (0.00) (6.93) (9.42) (4.62) (2.69) (6.93) (6.73) (4.62) (5.38) (6.93) (4.04) (4.62) (8.08) (6.93) (1.35) (4.88) (11.33) (6.93) (1.35) (2.31) (12.12) (6.93) (4.04) (2.31) (9.42) (6.93) (6.73) (2.31) (6.73) (7.29) (9.91) (2.31) (4.04) (9.25) (8.08) (2.31) (1.35) (9.25) (5.38) (2.31) (1.35) (9.25) (2.69) (2.31) (4.04) (9.25) (0.00) (2.31) (6.73) (9.25) (2.69) (2.31) (9.42) (9.25) (5.38) (2.31) (12.12) (9.25) (8.08) (0.00) (10.77) (11.56) (4.04) (0.00) (8.08) (11.56) (1.35) (0.00) (5.38) (12.24) (1.35) (0.00) (2.69) (11.56) (4.04) (0.00) (0.00) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 104
110 s (Insert arrangement 23-21) A (3.25) (9.78) M (7.34) (7.24) B (7.34) (7.24) N (3.25) (9.78) C (9.80) (3.12) P (0.00) (6.22) D (10.16) (1.65) R (4.06) (3.71) E (8.33) (6.07) S (5.44) (0.89) F (4.65) (9.19) T (2.39) (4.93) G (0.00) (10.31) U (2.39) (4.93) H (4.65) (9.19) V (5.44) (0.89) J (8.33) (6.07) W (4.06) (3.71) K (10.16) (1.65) X (0.00) (0.00) L (9.80) (3.12) Shell Arrangement Number of Size Service Supersedes size no. rating location II All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 105
111 s (Insert arrangement 23-23) position (3.06) (12.37) (2.04) (0.00) (1.02) (12.37) (4.08) (0.00) (1.02) (12.37) (6.12) (0.00) (3.06) (12.37) (8.16) (0.00) (6.12) (10.60) (10.20) (0.00) (4.08) (10.60) (12.24) (0.00) (2.04) (10.60) (11.22) (1.77) (0.00) (10.60) (9.18) (1.77) (2.04) (10.60) (7.14) (1.77) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 106
112 s (Insert arrangement 23-23) position (4.08) (10.60) (5.10) (1.77) (6.12) (10.60) (3.06) (1.77) (9.18) (8.83) (1.02) (1.77) (7.14) (8.83) (1.02) (1.77) (5.10) (8.83) (3.06) (1.77) (3.06) (8.83) (5.10) (1.77) (1.02) (8.83) (7.14) (1.77) (1.02) (8.83) (9.18) (1.77) (3.06) (8.83) (11.22) (1.77) (5.10) (8.83) (12.24) (3.53) (7.14) (8.83) (10.20) (3.53) (9.18) (8.83) (8.16) (3.53) (10.20) (7.07) (6.12) (3.53) (8.16) (7.07) (4.08) (3.53) (6.12) (7.07) (2.04) (3.53) (4.08) (7.07) (0.00) (3.53) (2.04) (7.07) (2.04) (3.53) (0.00) (7.07) (4.08) (3.53) (2.04) (7.07) (6.12) (3.53) (4.08) (7.07) (8.16) (3.53) (6.12) (7.07) (10.20) (3.53) (8.16) (7.07) (12.24) (3.53) (10.20) (7.07) (11.22) (5.30) (11.22) (5.30) (9.18) (5.30) (9.18) (5.30) (7.14) (5.30) (7.14) (5.30) (5.10) (5.30) (5.10) (5.30) (3.06) (5.30) (3.06) (5.30) (1.02) (5.30) (1.02) (5.30) (1.02) (5.30) (1.02) (5.30) (3.06) (5.30) (3.06) (5.30) (5.10) (5.30) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 107
113 s (Insert arrangement 23-23) position (5.10) (5.30) (7.14) (5.30) (7.14) (5.30) (9.18) (5.30) (9.18) (5.30) (11.22) (5.30) (11.22) (5.30) (10.20) (7.07) (12.24) (3.53) (8.16) (7.07) (10.20) (3.53) (6.12) (7.07) (8.16) (3.53) (4.08) (7.07) (6.12) (3.53) (2.04) (7.07) (4.08) (3.53) (0.00) (7.07) (2.04) (3.53) (2.04) (7.07) (0.00) (3.53) (4.08) (7.07) (2.04) (3.53) (6.12) (7.07) (4.08) (3.53) (8.16) (7.07) (6.12) (3.53) (10.20) (7.07) (8.16) (3.53) (9.18) (8.83) (10.20) (3.53) (7.14) (8.83) (12.24) (3.53) (5.10) (8.83) (11.22) (1.77) (3.06) (8.83) (9.18) (1.77) (1.02) (8.83) (7.14) (1.77) (1.02) (8.83) (5.10) (1.77) (3.06) (8.83) (3.06) (1.77) (5.10) (8.83) (1.02) (1.77) (7.14) (8.83) (1.02) (1.77) (9.18) (8.83) (3.06) (1.77) (6.12) (10.60) (5.10) (1.77) (4.08) (10.60) (7.14) (1.77) (2.04) (10.60) (9.18) (1.77) (0.00) (10.60) (11.22) (1.77) (2.04) (10.60) (12.24) (0.00) (4.08) (10.60) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 108
114 s (Insert arrangement 23-23) position (10.20) (0.00) (6.12) (10.60) (8.16) (0.00) (3.06) (12.37) (6.12) (0.00) (1.02) (12.37) (4.08) (0.00) (1.02) (12.37) (2.04) (0.00) (3.06) (12.37) (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location N All Standard contact Pin Socket M39029/ M39029/ FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 109
115 position s (Insert arrangement 23-32) A (2.54) (11.43) T (8.26) (0.64) B (8.26) (8.26) U (7.62) (3.18) C (10.80) (3.81) V (5.08) (6.35) D (11.43) (1.91) W (0.00) (7.62) E (9.53) (6.99) X (5.08) (6.35) F (5.08) (10.16) Y (7.62) (3.18) G (0.00) (11.43) Z (8.26) (0.64) H (5.08) (10.16) a (6.35) (4.45) J (9.53) (6.99) b (3.81) (7.62) K (11.43) (1.91) c (2.54) (3.81) L (10.80) (3.81) d (3.81) (0.00) M (8.26) (8.26) e (1.91) (3.81) N (2.54) (11.43) f (1.91) (3.81) P (0.00) (8.26) g (3.81) (0.00) R (3.81) (7.62) h (2.54) (3.81) S (6.35) (4.45) J (0.00) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 110
116 s (Insert arrangement 23-34) A (0.00) (11.43) U (.00) (7.62) B (4.45) (10.80) V (5.08) (5.72) C (8.26) (8.26) W (7.62) (1.27) D (10.80) (4.45) X (7.62) (2.54) E (11.43) (0.64) Y (3.81) (6.35) F (11.43) (3.18) Z (0.00) (7.62) G (9.53) (6.99) a (3.81) (6.35) H (6.35) (9.53) b (7.62) (2.54) J (2.54) (11.43) c (7.62) (1.27) K (2.54) (11.43) d (5.08) (5.72) L (6.35) (9.53) e (0.00) (3.81) M (9.53) (6.99) f (3.81) (1.27) N (11.43) (3.18) g (3.81) (2.54) P (11.43) (0.64) h (0.00) (3.81) R (10.80) (4.45) j (3.81) (2.54) S (8.26) (8.26) k (3.81) (1.27) T (4.45) (10.80) l (0.00) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 111
117 position s (Insert arrangement 23-35) (10.87) (6.12) (0.00) (1.19) (11.86) (3.91) (0.00) (3.61) (12.40) (1.55) (0.00) (6.02) (10.54) (0.00) (0.00) (8.43) (12.40) (1.55) (0.00) (10.85) (10.87) (3.61) (2.11) (12.07) (10.87) (6.02) (2.11) (9.65) (8.43) (8.46) (2.11) (7.24) (8.43) (6.05) (2.11) (4.83) (8.43) (3.63) (2.11) (2.41) (8.43) (1.22) (2.11) (0.00) (8.43) (1.19) (2.11) (2.41) (8.43) (3.61) (2.11) (4.83) (8.43) (6.02) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (6.32) (9.65) (2.11) (12.07) (6.32) (7.24) (4.22) (10.87) (6.32) (4.83) (4.22) (8.46) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 112
118 position MIL-STD-1560C s (Insert arrangement 23-35) (6.32) (2.41) (4.22) (6.05) (6.32) (0.00) (4.22) (3.63) (6.32) (2.41) (4.22) (1.22) (6.32) (4.83) (4.22) (1.19) (6.32) (7.24) (4.22) (3.61) (6.32) (9.65) (4.22) (6.02) (4.22) (10.87) (4.22) (8.43) (4.22) (8.46) (4.22) (10.85) (4.22) (6.05) (6.32) (9.65) (4.22) (3.63) (6.32) (7.24) (4.22) (1.22) (6.32) (4.83) (4.22) (1.19) (6.32) (2.41) (4.22) (3.61) (6.32) (0.00) (4.22) (6.02) (6.32) (2.41) (4.22) (8.43) (6.32) (4.83) (4.22) (10.85) (6.32) (7.24) (2.11) (12.07) (6.32) (9.65) (2.11) (9.65) (8.43) (8.46) (2.11) (7.24) (8.43) (6.05) (2.11) (4.83) (8.43) (3.63) (2.11) (2.41) (8.43) (1.22) (2.11) (0.00) (8.43) (1.19) (2.11) (2.41) (8.43) (3.61) (2.11) (4.83) (8.43) (6.02) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (10.87) (6.12) (2.11) (12.07) (11.86) (3.91) (0.00) (10.87) (12.40) (1.55) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 113
119 position MIL-STD-1560C s (Insert arrangement 23-35) (0.00) (8.46) (10.54) (0.00) (0.00) (6.05) (12.40) (1.55) (0.00) (3.63) (10.87) (3.61) (0.00) (1.22) (10.87) (6.02) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 114
120 position s (Insert arrangement 23-36) A (2.54) (11.43) V (3.81) (6.99) B (6.35) (10.16) W (7.62) (3.18) C (8.89) (6.99) X (7.62) (0.64) D (11.43) (2.54) Y (6.99) (4.45) E (11.43) (1.27) Z (3.81) (6.99) F (10.80) (5.08) a (0.00) (7.62) G (7.62) (8.89) b (3.81) (6.99) H (3.81) (10.80) c (6.99) (4.45) J (0.00) (11.43) d (7.62) (0.64) K (3.81) (10.80) e (7.62) (3.18) L (7.62) (8.89) f (3.81) (6.99) M (10.80) (5.08) g (.00) (3.81) N (11.43) (1.27) h (3.81) (3.18) P (11.43) (2.54) j (3.81) (0.64) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 115
121 position s (Insert arrangement 23-36) R (8.89) (6.99) k (0.00) (3.81) S (6.35) (10.16) l (3.81) (0.64) T (2.54) (11.43) m (3.81) (3.18) U (0.00) (8.26) n (0.00) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 116
122 position s (Insert arrangement 23-53) A (2.84) (11.56) e (5.72) (6.60) B (5.72) (9.91) f (8.53) (4.95) C (8.53) (8.26) g (8.53) (1.65) D (11.43) (3.30) h (8.53) (1.65) E (11.43) (0.00) k (8.53) (4.95) F (11.43) (3.30) m (5.72) (6.60) G (8.53) (8.26) n (2.84) (8.26) H (5.72) (10.41) p (0.00) (6.60) J (5.72) (10.41) q (2.84) (4.95) K (8.53) (8.26) r (5.72) (3.30) L (11.43) (3.30) s (5.72) (0.00) M (11.43) (0.00) t (5.72) (3.30) N (11.43) (3.30) u (2.84) (4.95) P (8.53) (8.26) v (0.00) (6.60) R (5.72) (9.91) w (2.84) (4.95) S (2.84) (11.56) x (5.72) (3.30) T (0.00) (9.91) y (5.72) (0.00) U (2.84) (8.26) z (5.72) (3.30) V (5.72) (6.60) AA (2.84) (4.95) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 117
123 position MIL-STD-1560C s (Insert arrangement 23-53) W (8.53) (4.95) BB (0.00) (3.30) X (8.53) (1.65) CC (2.84) (1.65) Y (8.53) (1.65) DD (2.84) (1.65) Z (8.53) (4.95) EE (0.00) (3.30) a (5.72) (6.60) FF (2.84) (1.65) b (2.84) (8.26) GG (2.84) (1.65) c (0.00) (9.91) HH (0.00) (0.00) d (2.84) (8.26) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 118
124 position s (Insert arrangement 23-55) A (2.84) (11.56) f (2.84) (8.26) B (5.72) (9.91) g (5.72) (6.60) C (8.53) (8.26) h (8.53) (4.95) D (11.43) (3.30) i (8.53) (1.65) E (11.43) (0.00) J (8.53) (1.65) F (11.43) (3.30) k (8.53) (4.95) G (8.53) (8.26) m (5.72) (6.60) H (5.72) (9.91) n (2.84) (8.26) J (2.84) (11.56) p (0.00) (6.60) K (2.84) (11.56) q (2.84) (4.95) L (5.72) (9.91) r (5.72) (3.30) M (8.53) (8.26) s (5.72) (0.00) N (11.43) (3.30) t (5.72) (3.30) P (11.43) (0.00) u (2.84) (4.95) R (11.43) (3.30) v (0.00) (6.60) S (8.53) (8.26) w (2.84) (4.95) T (5.72) (9.91) x (5.72) (3.30) U (2.84) (11.56) y (5.72) (0.00) V (0.00) (9.91) z (5.72) (3.30) FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 119
125 position s (Insert arrangement 23-55) W (2.84) (8.26) AA (2.84) (4.95) X (5.72) (6.60) BB (0.00) (3.30) Y (8.53) (4.95) CC (2.84) (1.65) Z (8.53) (1.65) DD (2.84) (1.65) a (8.53) (1.65) EE (0.00) (3.30) b (8.53) (4.95) FF (2.84) (1.65) c (5.72) (6.60) GG (2.84) (1.65) d (2.84) (8.26) HH (0.00) (0.00) e (0.00) (9.91) Shell Arrangement Number of Size Service Supersedes size no. rating location I All ---- FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 120
126 s (Insert arrangement 23-97) A (0.00) (8.74) J (8.33) (6.07) B (5.33) (6.86) K (10.16) (1.65) C (9.80) (3.12) L (9.80) (3.12) D (10.16) (1.65) M (5.33) (6.86) E (8.33) (6.07) N (0.00) (3.96) F (4.65) (9.19) P (3.05) (0.76) G (0.00) (10.31) R (0.00) (5.54) H (4.65) (9.19) S (3.05) (0.76) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 121
127 s (Insert arrangement 23-99) A (0.00) (10.26) G (10.26) (0.00) B (7.62) (6.86) H (7.62) (6.86) C (10.26) (0.00) J (3.05) (3.81) D (6.10) (5.33) K (0.00) (1.52) E (0.00) (7.62) L (3.05) (3.81) F (6.10) (5.33) Shell Arrangement Number of Size Service Supersedes size no. rating location II All MS FIGURE 8. Insert arrangement, electrical connector, shell size 23 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 122
128 position s (Insert arrangement 25-1) (12.17) (7.09) (0.00) (1.19) (13.21) (4.83) (0.00) (3.61) (13.87) (2.41) (0.00) (6.02) (14.10) (0.00) (0.00) (8.43) (13.87) (2.41) (0.00) (10.85) (13.21) (4.83) (0.00) (14.10) (12.17) (7.09) (2.11) (12.07) (10.77) (9.07) (2.11) (9.65) (10.54) (4.83) (2.11) (7.24) (10.54) (2.41) (2.11) (4.83) (10.54) (0.00) (2.11) (2.41) (10.54) (2.41) (2.11) (0.00) (10.54) (4.83) (2.11) (2.41) (10.77) (9.07) (2.11) (4.83) (8.43) (11.28) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600). 123
129 s (Insert arrangement 25-1) (8.43) (6.02) (2.11) (12.07) (8.43) (3.61) (4.06) (13.49) (8.43) (1.19) (4.22) (10.85) (8.43) (1.19) (4.22) (8.43) (8.43) (3.61) (4.22) (6.02) (8.43) (6.02) (4.22) (3.61) (8.43) (8.43) (4.22) (1.19) (8.43) (10.85) (4.22) (1.19) (6.32) (12.60) (4.22) (3.61) (6.32) (9.65) (4.22) (6.02) (6.32) (7.24) (4.22) (8.43) (6.32) (4.83) (4.22) (10.85) (6.32) (2.41) (4.22) (13.26) (6.32) (0.00) (6.32) (12.60) (6.32) (2.41) (6.32) (9.65) (6.32) (4.83) (6.32) (7.24) (6.32) (7.24) (6.32) (4.83) (6.32) (9.65) (6.32) (2.41) (6.32) (12.07) (6.32) (0.00) (4.06) (13.49) (6.32) (2.41) (4.22) (10.85) (6.32) (4.83) (4.22) (8.43) (6.32) (7.24) (4.22) (6.02) (6.32) (9.65) (4.22) (3.61) (6.32) (12.07) (4.22) (1.19) (8.43) (11.28) (4.22) (1.19) (8.43) (8.43) (4.22) (3.61) (8.43) (6.02) (4.22) (6.02) (8.43) (3.61) (4.22) (8.43) (8.43) (1.19) (4.22) (10.85) (8.43) (1.19) (4.22) (13.26) (8.43) (3.61) (2.11) (12.07) (8.43) (6.02) (2.11) (9.65) (8.43) (8.43) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 124
130 position s (Insert arrangement 25-1) (2.11) (7.24) (8.43) (10.85) (2.11) (4.83) (10.77) (9.07) (2.11) (2.41) (10.54) (4.83) (2.11) (0.00) (10.54) (2.41) (2.11) (2.41) (10.54) (0.00) (2.11) (4.83) (10.54) (2.41) (2.11) (7.24) (10.54) (4.83) (2.11) (9.65) (10.77) (9.07) (2.11) (12.07) (12.17) (7.09) (0.00) (13.26) (13.21) (4.83) (0.00) (10.85) (13.87) (2.41) (0.00) (8.43) (14.10) (0.00) (0.00) (6.02) (13.87) (2.41) (0.00) (3.61) (13.21) (4.83) (0.00) (1.19) (12.17) (7.09) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 125
131 position s (Insert arrangement 25-2) (13.97) (.99) (1.35) (12.75) (13.97) (1.73) (1.35) (10.08) (11.66) (6.43) (1.35) (7.42) (13.28) (4.45) (1.35) (4.75) (11.66) (2.34) (1.35) (2.08) (11.66) (0.36) (1.35) (0.58) (11.66) (3.10) (1.35) (3.25) (12.93) (5.46) (1.35) (5.92) (11.66) (7.80) (1.35) (8.59) (8.99) (10.67) (1.35) (11.25) (8.99) (8.00) (1.35) (13.92) (8.99) (5.33) (3.91) (13.34) (8.99) (2.67) (3.91) (10.67) (8.99) (0.00) (3.91) (8.00) (8.99) (2.67) (3.91) (5.33) (8.99) (5.33) (3.91) (2.67) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 126
132 position MIL-STD-1560C s (Insert arrangement 25-2) (8.99) (8.00) (3.91) (0.00) (8.99) (10.67) (3.91) (2.67) (6.48) (11.61) (3.91) (5.33) (6.48) (8.94) (3.91) (8.00) (6.48) (6.27) (3.91) (10.67) (6.48) (3.61) (3.91) (13.34) (6.48) (0.94) (6.48) (11.61) (6.48) (1.73) (6.48) (8.94) (6.48) (4.39) (6.48) (6.27) (6.48) (7.06) (6.48) (3.61) (6.48) (9.73) (6.48) (0.94) (6.48) (12.40) (6.48) (1.73) (3.91) (13.34) (6.48) (4.39) (3.91) (10.67) (6.48) (7.06) (3.91) (8.00) (6.48) (9.73) (3.91) (5.33) (6.48) (12.40) (3.91) (2.67) (8.99) (10.67) (3.91) (0.00) (8.99) (8.00) (3.91) (2.67) (8.99) (5.33) (3.91) (5.33) (8.99) (2.67) (3.91) (8.00) (8.99) (0.00) (3.91) (10.67) (8.99) (2.67) (3.91) (13.34) (8.99) (5.33) (1.35) (12.75) (8.99) (8.00) (1.35) (10.08) (8.99) (10.67) (1.35) (7.42) (11.66) (6.43) (1.35) (4.75) (13.28) (4.45) (1.35) (2.08) (11.66) (2.34) (1.35) (0.58) (11.66) (0.36) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 127
133 position s (Insert arrangement 25-2) (1.35) (3.25) (11.66) (3.10) (1.35) (5.92) (12.93) (5.46) (1.35) (8.59) (11.66) (7.80) (1.35) (11.25) (13.97) (0.99) (1.35) (13.92) (13.97) (1.73) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M All MS FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 128
134 position s (Insert arrangement 25-4) 129 A (1.75) (13.49) f (10.46) (0.00) B (5.16) (12.57) g (9.58) (3.35) C (8.23) (10.80) h (7.90) (6.38) D (10.77) (8.28) k (5.38) (8.74) E (12.52) (5.21) m (2.18) (10.08) F (13.49) (1.75) n (2.18) (10.08) G (13.49) (1.75) p (5.38) (8.74) H (12.52) (5.21) q (7.90) (6.38) J (10.77) (8.28) r (9.58) (3.35) K (8.23) (10.80) s (10.46) (0.00) L (5.16) (12.57) t (9.58) (3.35) M (1.75) (13.49) u (7.90) (6.38) N (1.75) (13.49) v (5.38) (8.74) P (5.16) (12.57) w (2.18) (10.08) R (8.23) (10.80) x (1.75) (6.68) S (10.77) (8.28) y (4.37) (3.78) T (12.52) (5.21) z (6.55) (0.00) U (13.49) (1.75) AA (4.37) (3.78) V (13.49) (1.75) BB (1.75) (6.68) W (12.52) (5.21) CC (1.75) (6.68) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600)
135 position s (Insert arrangement 25-4) X (10.77) (8.28) DD (4.37) (3.78) Y (8.23) (10.80) EE (6.55) (0.00) Z (5.16) (12.57) FF (4.37) (3.78) a (1.75) (13.49) GG (1.75) (6.68) b (2.18) (10.08) HH (0.00) (3.35) c (5.38) (8.74) JJ (2.18) (0.00) d (7.90) (6.38) KK (0.00) (3.35) e (9.58) (3.35) LL (2.18) (0.00) Shell size Arrangement no Number of Size Service rating location y, z, AA, DD, EE, FF, LL, JJ 8 16 I All others Supersedes MS FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 130
136 (Inactive for new design for MIL-DTL For new design, use arrangement no ) s (Insert arrangement 25-7) position (12.55) (6.15) (0.00) (2.69) (13.54) (3.51) (0.00) (5.38) (13.97) (0.71) (0.00) (7.87) (13.82) (2.11) (0.00) (14.00) (13.11) (4.85) (1.42) (13.92) (11.86) (7.42) (2.41) (11.71) (11.05) (8.56) (1.73) (9.40) (10.13) (6.32) (2.34) (7.06) (11.20) (4.14) (2.41) (4.65) (11.81) (1.80) (2.26) (4.52) (11.94) (0.61) (2.39) (7.04) (11.58) (3.00) (1.75) (9.55) (10.74) (5.26) (1.22) (11.89) (9.45) (7.32) (4.19) (13.34) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 131
137 s (Insert arrangement 25-7) (10.13) (9.63) (4.72) (11.00) (9.12) (10.62) (4.17) (8.64) (8.66) (8.23) (4.60) (5.72) (7.82) (5.64) (4.37) (5.66) (7.70) (5.66) (4.04) (8.81) (7.80) (9.07) (3.58) (11.40) (7.98) (11.48) (2.82) (13.69) (6.78) (12.22) (6.78) (12.22) (6.83) (9.80) (6.83) (9.80) (6.27) (7.47) (6.27) (7.47) (6.05) (0.00) (6.05) (0.00) (6.02) (7.42) (6.02) (7.42) (5.79) (10.46) (5.79) (10.46) (5.51) (12.85) (5.51) (12.85) (4.19) (13.34) (9.12) (10.62) (4.72) (11.00) (8.66) (8.23) (4.17) (8.64) (7.82) (5.64) (4.60) (5.72) (7.70) (5.66) (4.37) (5.66) (7.80) (9.07) (4.04) (8.81) (7.98) (11.48) (3.58) (11.40) (11.05) (8.56) (2.82) (13.69) (10.13) (6.32) (1.42) (13.92) (11.20) (4.14) (2.41) (11.71) (11.81) (1.80) (1.73) (9.40) (11.94) (.61) (2.34) (7.06) (11.58) (3.00) (2.41) (4.65) (10.74) (5.26) (2.26) (4.52) (9.45) (7.32) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 132
138 s (Insert arrangement 25-7) position (2.39) (7.04) (10.13) (9.63) (1.75) (9.55) (12.55) (6.15) (1.22) (11.89) (13.54) (3.51) (0.00) (11.96) (13.97) (0.71) (0.00) (7.70) (13.82) (2.11) (0.00) (5.28) (13.11) (4.85) (0.00) (2.64) (11.86) (7.42) (0.00) (0.00) Shell size Arrangement no Number of Size Service rating location Pin Standard contact Socket 2 8 (See note) Twinax 25, 75 M39029/ M39029/ D M All others M39029/ M39029/ NOTE: To meet environmental sealing requirements, size 8 shielded used with this insert arrangement may require separate, non-standard sealing boots that are furnished with the connector. For this insert arrangement, some connector grommet designs use a heat shrink sleeve only with the size 8 shielded to meet environmental sealing requirements. When heat shrink sleeves are used, sealing boots are not used, and when sealing boots are used, heat shrink sleeves are not used. Heat shrink sleeves have a maximum temperature rating of 175 C maximum. When heat shrink sleeves are used, connectors rated to 200 C max are derated to 175 C max. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 133
139 (Inactive for new design for MIL-DTL For new design, use arrangement no ) s (Insert arrangement 25-8) position location A (0.00) (10.82) B (8.46) (6.76) C (10.54) (2.41) D (4.70) (9.75) E (4.70) (9.75) F (10.54) (2.41) G (8.46) (6.76) H (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating 134 location Pin Standard contact Socket Twinax All M39029/ M39029/ NOTE: To meet environmental sealing requirements, size 8 shielded used with this insert arrangement may require separate, non-standard sealing boots that are furnished with the connector. For this insert arrangement, some connector grommet designs use a heat shrink sleeve only with the size 8 shielded to meet environmental sealing requirements. When heat shrink sleeves are used, sealing boots are not used, and when sealing boots are used, heat shrink sleeves are not used. When heat shrink sleeves are used, connectors rated to 200 C max are derated to 175 C max. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600)
140 (INSERT ARRANGEMENT PATTERN ENTICAL TO 25-7, EXCEPT 25-9 BOOT IN ACCORDANCE WITH MIL-DTL-38999/62) s (Insert arrangement 25-9) USES SEALING position (12.55) (6.15) (0.00) (2.69) (13.54) (3.51) (0.00) (5.38) (13.97) (0.71) (0.00) (7.87) (13.82) (2.11) (0.00) (14.00) (13.11) (4.85) (1.42) (13.92) (11.86) (7.42) (2.41) (11.71) (11.05) (8.56) (1.73) (9.40) (10.13) (6.32) (2.34) (7.06) (11.20) (4.14) (2.41) (4.65) (11.81) (1.80) (2.26) (4.52) (11.94) (0.61) (2.39) (7.04) (11.58) (3.00) (1.75) (9.55) (10.74) (5.26) (1.22) (11.89) (9.45) (7.32) (4.19) (13.34) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 135
141 s (Insert arrangement 25-9) (10.13) (9.63) (4.72) (11.00) (9.12) (10.62) (4.17) (8.64) (8.66) (8.23) (4.60) (5.72) (7.82) (5.64) (4.37) (5.66) (7.70) (5.66) (4.04) (8.81) (7.80) (9.07) (3.58) (11.40) (7.98) (11.48) (2.82) (13.69) (6.78) (12.22) (6.78) (12.22) (6.83) (9.80) (6.83) (9.80) (6.27) (7.47) (6.27) (7.47) (6.05) (0.00) (6.05) (0.00) (6.02) (7.42) (6.02) (7.42) (5.79) (10.46) (5.79) (10.46) (5.51) (12.85) (5.51) (12.85) (4.19) (13.34) (9.12) (10.62) (4.72) (11.00) (8.66) (8.23) (4.17) (8.64) (7.82) (5.64) (4.60) (5.72) (7.70) (5.66) (4.37) (5.66) (7.80) (9.07) (4.04) (8.81) (7.98) (11.48) (3.58) (11.40) (11.05) (8.56) (2.82) (13.69) (10.13) (6.32) (1.42) (13.92) (11.20) (4.14) (2.41) (11.71) (11.81) (1.80) (1.73) (9.40) (11.94) (.61) (2.34) (7.06) (11.58) (3.00) (2.41) (4.65) (10.74) (5.26) (2.26) (4.52) (9.45) (7.32) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 136
142 s (Insert arrangement 25-9) position (2.39) (7.04) (10.13) (9.63) (1.75) (9.55) (12.55) (6.15) (1.22) (11.89) (13.54) (3.51) (0.00) (11.96) (13.97) (0.71) (0.00) (7.70) (13.82) (2.11) (0.00) (5.28) (13.11) (4.85) (0.00) (2.64) (11.86) (7.42) (0.00) (0.00) Shell size Arrangement no Number of Size Service rating location Pin Standard contact Socket 8 2 Twinax 25, 75 M39029/ M39029/ (See note) 97 22D M All others M39029/ M39029/ NOTE: For this insert arrangement, sealing boots in accordance with MIL-DTL-38999/62 shall be used to environmentally seal size 8 twinax. Heat shrink sleeves are not used when MIL-DTL-38999/62 sealing boots are used. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 137
143 (INSERT ARRANGEMENT PATTERN ENTICAL TO 25-8, EXCEPT USES SEALING BOOT IN ACCORDANCE WITH MIL-DTL-38999/62) s (Insert arrangement 25-10) position location A (0.00) (10.82) B (8.46) (6.76) C (10.54) (2.41) D (4.70) (9.75) E (4.70) (9.75) F (10.54) (2.41) G (8.46) (6.76) H (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location Pin Standard contact Socket Twinax All M39029/ M39029/ NOTE: For this insert arrangement, sealing boots in accordance with MIL-DTL-38999/62 shall be used to environmentally seal size 8 twinax. Heat shrink sleeves are not used when MIL-DTL-38999/62 sealing boots are used. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 138
144 s (Insert arrangement 25-11) A (0.00) (10.95) G (10.95) (0.00) B (7.72) (7.72) H (7.72) (7.72) C (10.95) (0.00) J (0.00) (2.59) D (7.72) (7.72) K (2.34) (4.06) E (0.00) (10.95) L (2.34) (4.06) F (7.72) (7.72) NOTES: 1. All dimensions are true position. 2. Front face of pin insert shown. Shell size Arrangement no Number of Size Service rating location A,B,C,D,E,F, G,H,J 9 10 N 2 20 L,K FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 139
145 s (Insert arrangement 25-19) A (0.00) (10.39) L (8.99) (5.21) B (5.99) (10.39) M (5.99) (10.39) C (8.99) (5.21) N (3.00) (5.21) D (11.99) (0.00) P (3.00) (5.21) E (8.99) (5.21) R (5.99) (0.00) F (5.99) (10.39) S (3.00) (5.21) G (.00) (10.39) T (3.00) (5.21) H (5.99) (10.39) U (5.99) (0.00) J (8.99) (5.21) V (0.00) (0.00) K (11.99) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 140
146 position s (Insert arrangement 25-20) A (0.00) (10.34) S (5.94) (12.98) B (5.94) (12.98) T (6.17) (6.86) C (8.94) (10.44) U (9.07) (3.45) D (11.84) (6.99) V (11.43) (4.65) E (13.46) (2.82) w (0.00) (3.33) F (13.64) (1.52) X (11.43) (4.65) G (11.86) (7.92) Y (9.07) (3.45) H (5.28) (8.97) Z (6.17) (6.86) J (0.00) (13.74) (4.95) (2.92) K (5.28) (8.97) (8.05) (1.55) L (11.86) (7.92) (8.05) (1.55) M (13.64) (1.52) (4.95) (2.92) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 141
147 position s (Insert arrangement 25-20) N (13.46) (2.82) (0.00) (2.51) P (11.84) (6.99) (3.58) (0.46) R (8.94) (10.44) (3.58) (0.46) Shell size Arrangement no Number of Size Service rating location Pin Standard contact Socket 3 8 Twinax A,H,K M39029/ M39029/ Coax 2,3 M39029/ M39029/ W, 5 M39029/ M39029/ C,D,E,F, J,M,N,P, R,T,U,Y, M39029/ M39029/ N Z B,G,L,S, V,X,1,4, 6, 7 M39029/ M39029/ NOTE: For this insert arrangement, size 8 twinax are intended to be used with a heat shrink sleeve to effect environmental sealing to the connector and cable. Heat shrink sleeves used with size 8 twinax are rated to 175 C maximum. Connectors rated to 200 C max are derated to 175 C max when heat shrink sleeves are used. For environmental sealing and prevention of splaying, some insert arrangement grommet designs may use a separate, non-standard boot that is supplied with the connector for use with size 8 twinax. If a heat shrink sleeve is used, then a sealing boot is not used. If a sealing boot is used, then a heat shrink sleeve is not used. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 142
148 position (This insert arrangement pattern is identical to arrangement 25-20, except this arrangement is designed to use MIL-DTL-38999/62 sealing boots with size 8 twinax.) s (Insert arrangement 25-21) A (0.00) (10.34) S (5.94) (12.98) B (5.94) (12.98) T (6.17) (6.86) C (8.94) (10.44) U (9.07) (3.45) D (11.84) (6.99) V (11.43) (4.65) E (13.46) (2.82) w (0.00) (3.33) F (13.64) (1.52) X (11.43) (4.65) G (11.86) (7.92) Y (9.07) (3.45) H (5.28) (8.97) Z (6.17) (6.86) J (0.00) (13.74) (4.95) (2.92) K (5.28) (8.97) (8.05) (1.55) L (11.86) (7.92) (8.05) (1.55) M (13.64) (1.52) (4.95) (2.92) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 143
149 position MIL-STD-1560C s (Insert arrangement 25-21) N (13.46) (2.82) (0.00) (2.51) P (11.84) (6.99) (3.58) (0.46) R (8.94) (10.44) (3.58) (0.46) Shell size Arrangement no Number of Size Service rating location Pin Standard contact Socket 3 8 Twinax A,H,K M39029/ M39029/ Coax 2,3 M39029/ M39029/ W, 5 M39029/ M39029/ C,D,E,F, J,M,N,P, R,T,U,Y, M39029/ M39029/ N Z B,G,L,S, V,X,1,4, 6, 7 M39029/ M39029/ NOTE: For this insert arrangement, sealing boots in accordance with MIL-DTL-38999/62 shall be used to environmentally seal size 8 twinax. Heat shrink sleeves are not used when MIL-DTL-38999/62 sealing boots are used. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 144
150 s (Insert arrangement 25-23) (2.04) (14.13) (2.04) (0.00) (0.00) (14.13) (4.08) (0.00) (2.04) (14.13) (6.12) (0.00) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 145
151 s (Insert arrangement 25-23) (7.14) (12.37) (8.16) (0.00) (5.10) (12.37) (10.20) (0.00) (3.06) (12.37) (12.24) (0.00) (1.02) (12.37) (14.28) (0.00) (1.02) (12.37) (13.26) (1.77) (3.06) (12.37) (11.22) (1.77) (5.10) (12.37) (9.18) (1.77) (7.14) (12.37) (7.14) (1.77) (8.16) (10.60) (5.10) (1.77) (6.12) (10.60) (3.06) (1.77) (4.08) (10.60) (1.02) (1.77) (2.04) (10.60) (1.02) (1.77) (0.00) (10.60) (3.06) (1.77) (2.04) (10.60) (5.10) (1.77) (4.08) (10.60) (7.14) (1.77) (6.12) (10.60) (9.18) (1.77) (8.16) (10.60) (11.22) (1.77) (11.22) (8.83) (13.26) (1.77) (9.18) (8.83) (12.24) (3.53) (7.14) (8.83) (10.20) (3.53) (5.10) (8.83) (8.16) (3.53) (3.06) (8.83) (6.12) (3.53) (1.02) (8.83) (4.08) (3.53) (1.02) (8.83) (2.04) (3.53) (3.06) (8.83) (0.00) (3.53) (5.10) (8.83) (2.04) (3.53) (7.14) (8.83) (4.08) (3.53) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 146
152 s (Insert arrangement 25-23) (9.18) (8.83) (6.12) (3.53) (11.22) (8.83) (8.16) (3.53) (12.24) (7.07) (10.20) (3.53) (10.20) (7.07) (12.24) (3.53) (8.16) (7.07) (13.26) (5.30) (6.12) (7.07) (11.22) (5.30) (4.08) (7.07) (9.18) (5.30) (2.04) (7.07) (7.14) (5.30) (0.00) (7.07) (5.10) (5.30) (2.04) (7.07) (3.06) (5.30) (4.08) (7.07) (1.02) (5.30) (6.12) (7.07) (1.02) (5.30) (8.16) (7.07) (3.06) (5.30) (10.20) (7.07) (5.10) (5.30) (12.24) (7.07) (7.14) (5.30) (13.26) (5.30) (9.18) (5.30) (11.22) (5.30) (11.22) (5.30) (9.18) (5.30) (13.26) (5.30) (7.14) (5.30) (12.24) (7.07) (5.10) (5.30) (10.20) (7.07) (3.06) (5.30) (8.16) (7.07) (1.02) (5.30) (6.12) (7.07) (1.02) (5.30) (4.08) (7.07) (3.06) (5.30) (2.04) (7.07) (5.10) (5.30) (0.00) (7.07) (7.14) (5.30) (2.04) (7.07) (9.18) (5.30) (4.08) (7.07) (11.22) (5.30) (6.12) (7.07) (13.26) (5.30) (8.16) (7.07) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 147
153 s (Insert arrangement 25-23) (12.24) (3.53) (10.20) (7.07) (10.20) (3.53) (12.24) (7.07) (8.16) (3.53) (11.22) (8.83) (6.12) (3.53) (9.18) (8.83) (4.08) (3.53) (7.14) (8.83) (2.04) (3.53) (5.10) (8.83) (0.00) (3.53) (3.06) (8.83) (2.04) (3.53) (1.02) (8.83) (4.08) (3.53) (1.02) (8.83) (6.12) (3.53) (3.06) (8.83) (8.16) (3.53) (5.10) (8.83) (10.20) (3.53) (7.14) (8.83) (12.24) (3.53) (9.18) (8.83) (13.26) (1.77) (11.22) (8.83) (11.22) (1.77) (8.16) (10.60) (9.18) (1.77) (6.12) (10.60) (7.14) (1.77) (4.08) (10.60) (5.10) (1.77) (2.04) (10.60) (3.06) (1.77) (0.00) (10.60) (1.02) (1.77) (2.04) (10.60) (1.02) (1.77) (4.08) (10.60) (3.06) (1.77) (6.12) (10.60) (5.10) (1.77) (8.16) (10.60) (7.14) (1.77) (7.14) (12.37) (9.18) (1.77) (5.10) (12.37) (11.22) (1.77) (3.06) (12.37) (13.26) (1.77) (1.02) (12.37) (14.28) (0.00) (1.02) (12.37) (12.24) (0.00) (3.06) (12.37) (10.20) (0.00) (5.10) (12.37) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 148
154 s (Insert arrangement 25-23) (8.16) (0.00) (7.14) (12.37) (6.12) (0.00) (2.04) (14.13) (4.08) (0.00) (0.00) (14.13) (2.04) (0.00) (2.04) (14.13) (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location N All Standard contact Pin Socket M39029/ M39029/ FIGURE 9. Insert arrangement, electrical connector, shell size 25 (Series I, III, IV of MIL-DTL-38999, Series I of MIL-DTL-27599, and Series A of SAE-AS29600) 149
155 s (Insert arrangement 25-24) A (0.00) (11.99) N (10.24) (7.57) B (5.84) (10.41) P (5.84) (10.41) C (10.24) (7.57) R (0.00) (5.94) D (11.71) (2.54) S (5.84) (4.37) E (10.49) (3.40) T (4.72) (1.57) F (9.40) (8.53) U (5.36) (6.78) G (5.84) (11.20) V (0.00) (8.20) H (0.00) (12.57) W (5.36) (6.78) J (5.84) (11.20) X (4.72) (1.57) K (9.40) (8.53) Y (5.84) (4.37) L (10.49) (3.40) Z (0.00) (0.71) M (11.71) (2.54) a (0.00) (3.84) Shell size Arrangement no Number of Size Service rating I location A,B,D,E,LM P,R,S,T,X,Y All others FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 150
156 position s (Insert arrangement 25-29) A (0.00) (12.22) S (2.31) (8.15) B (6.55) (10.31) T (2.31) (8.15) C (10.03) (7.04) U (5.79) (4.93) D (11.91) (2.77) V (8.10) (0.00) E (11.91) (2.77) W (6.10) (4.60) F (10.03) (7.04) X (2.31) (7.37) G (6.68) (10.31) Y (2.31) (7.37) H (2.31) (11.99) Z (6.10) (4.60) J (2.31) (11.99) a (8.10) (0.00) K (6.68) (10.31) b (5.79) (4.93) L (10.03) (7.04) c (0.00) (4.09) M (11.91) (2.77) d (3.40) (0.00) N (11.91) (2.77) e (0.00) (3.30) P (10.03) (7.04) f (3.40) (0.00) R (6.55) (10.31) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 151
157 position s (Insert arrangement 25-35) (12.17) (7.09) (0.00) (1.19) (13.21) (4.83) (0.00) (3.61) (13.87) (2.41) (0.00) (6.02) (14.10) (0.00) (0.00) (8.43) (13.87) (2.41) (0.00) (10.85) (13.21) (4.83) (0.00) (14.10) (12.17) (7.09) (2.11) (12.07) (10.77) (9.07) (2.11) (9.65) (10.54) (4.83) (2.11) (7.24) (10.54) (2.41) (2.11) (4.83) (10.54).000 (0.00) (2.11) (2.41) (10.54) (2.41) (2.11) (0.00) (10.54) (4.83) (2.11) (2.41) (10.77) (9.07) (2.11) (4.83) (8.43) (11.28) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (8.43) (6.02) (2.11) (12.07) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 152
158 s (Insert arrangement 25-35) (8.43) (3.61) (4.06) (13.49) (8.43) (1.19) (4.22) (10.85) (8.43) (1.19) (4.22) (8.43) (8.43) (3.61) (4.22) (6.02) (8.43) (6.02) (4.22) (3.61) (8.43) (8.43) (4.22) (1.19) (8.43) (10.85) (4.22) (1.19) (6.32) (12.60) (4.22) (3.61) (6.32) (9.65) (4.22) (6.02) (6.32) (7.24) (4.22) (8.43) (6.32) (4.83) (4.22) (10.85) (6.32) (2.41) (4.22) (13.26) (6.32) (0.00) (6.32) (12.60) (6.32) (2.41) (6.32) (9.65) (6.32) (4.83) (6.32) (7.24) (6.32) (7.24) (6.32) (4.83) (6.32) (9.65) (6.32) (2.41) (6.32) (12.07) (6.32) (0.00) (4.06) (13.49) (6.32) (2.41) (4.22) (10.85) (6.32) (4.83) (4.22) (8.43) (6.32) (7.24) (4.22) (6.02) (6.32) (9.65) (4.22) (3.61) (6.32) (12.07) (4.22) (1.19) (8.43) (11.28) (4.22) (1.19) (8.43) (8.43) (4.22) (3.61) (8.43) (6.02) (4.22) (6.02) (8.43) (3.61) (4.22) (8.43) (8.43) (1.19) (4.22) (10.85) (8.43) (1.19) (4.22) (13.26) (8.43) (3.61) (2.11) (12.07) (8.43) (6.02) (2.11) (9.65) (8.43) (8.43) (2.11) (7.24) (8.43) (10.85) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 153
159 position MIL-STD-1560C s (Insert arrangement 25-35) (2.11) (4.83) (10.77) (9.07) (2.11) (2.41) (10.54) (4.83) (2.11) (0.00) (10.54) (2.41) (2.11) (2.41) (10.54) (0.00) (2.11) (4.83) (10.54) (2.41) (2.11) (7.24) (10.54) (4.83) (2.11) (9.65) (10.77) (9.07) (2.11) (12.07) (12.17) (7.09) (0.00) (13.26) (13.21) (4.83) (0.00) (10.85) (13.87) (2.41) (0.00) (8.43) (14.10) (0.00) (0.00) (6.02) (13.87) (2.41) (0.00) (3.61) (13.21) (4.83) (0.00) (1.19) (12.17) (7.09) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 154
160 position s (Insert arrangement 25-37) A (.00) (11.99) W (6.15) (5.99) B (4.70) (11.99) X (8.28) (2.18) C (8.46) (9.70) Y (8.28) (2.18) D (11.20) (6.32) Z (6.15) (5.99) E (12.70) (2.18) a (2.18) (8.13) F (12.70) (2.18) b (2.18) (8.13) G (11.20) (6.32) c (6.15) (5.99) H (8.46) (9.70) d (8.28) (2.18) J (4.72) (11.99) e (8.28) (2.18) K (.00) (11.99) f (6.15) (5.99) L (4.72) (11.99) g (2.18) (8.13) M (8.46) (9.70) h (.00) (4.37) N (11.20) (6.32) k (3.91) (2.18) P (12.70) (2.18) m (3.91) (2.18) R (12.70) (2.18) n (.00) (4.37) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 155
161 position MIL-STD-1560C s (Insert arrangement 25-37) S (11.20) (6.32) p (3.91) (2.18) T (8.46) (9.70) q (3.91) (2.18) U (4.72) (11.99) r (.00) (.00) V (2.18) (8.13) Shell Arrangement Number of Size Service Supersedes size no. rating location II All FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 156
162 position s (Insert arrangement 25-43) A (1.75) (13.49) Z (1.75) (13.49) B (5.16) (12.57) a (4.37) (8.74) C (8.23) (10.80) b (6.55) (4.37) D (10.77) (8.28) c (8.74) (0.00) E (12.52) (5.21) d (8.74) (4.37) F (13.49) (1.75) e (4.37) (8.74) G (13.49) (1.75) f (0.00) (8.74) H (12.52) (5.21) g (4.37) (8.74) J (10.77) (8.28) h (8.74) (4.37) K (8.23) (10.80) k (8.74) (0.00) L (5.16) (12.57) m (6.55) (4.37) M (0.00) (13.49) n (4.37) (8.74) N (5.16) (12.57) p (0.00) (8.74) P (8.23) (10.80) q (2.18) (4.37) R (10.77) (8.28) r (4.37) (0.00) S (12.52) (5.21) s (4.37) (4.37) T (13.49) (1.75) t (0.00) (4.37) U (13.49) (1.75) u (4.37) (4.37) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 157
163 position MIL-STD-1560C s (Insert arrangement 25-43) V (12.52) (5.21) v (4.37) (0.00) W (10.77) (8.28) w (2.18) (4.37) X (8.23) (10.80) x (0.00) (0.00) Y (5.16) (12.57) Shell size Arrangement no Number of Size Service rating location a,b,c,d,e,f,g,h,k,m, n,p,q,r,s,t,u,v,w,x I All others Supersedes MS FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 158
164 (Inactive for new design for MIL-DTL For new design, use arrangement no ) position s (Insert arrangement 25-46) A (1.65) (13.54) a (10.26) (3.18) B (6.99) (11.84) b (11.10) (0.00) C (10.67) (8.56) c (10.26) (3.18) D (12.45) (5.77) d (7.98) (5.61) E (13.49) (2.36) e (6.22) (8.56) F (13.49) (2.36) f (3.45) (10.77) G (12.45) (5.77) g (0.00) (10.03) H (10.67) (8.56) h (3.45) (10.77) J (6.99) (11.84) k (6.22) (8.56) K (1.65) (13.54) m (7.98) (5.61) L (1.65) (13.54) n (10.26) (3.18) M (6.99) (11.84) p (11.10) (0.00) N (10.67) (8.56) q (10.26) (3.18) P (12.45) (5.77) r (7.98) (5.61) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 159
165 position Shell size s (Insert arrangement 25-46) R (13.49) (2.36) s (6.22) (8.56) S (13.49) (2.36) t (3.45) (10.77) T (12.45) (5.77) u (0.00) (10.03) U (10.67) (8.56) v (2.46) (6.73) V (6.99) (11.84) w (4.57) (0.00) W (1.65) (13.54) x (2.46) (6.73) X (3.45) (10.77) y (2.46) (6.73) Y (6.22) (8.56) z (4.57) (0.00) Z (7.98) (5.61) AA (2.46) (6.73) Arrangement no. Number of NOTES: Size 8 (see note) Service rating location Standard contact Pin Socket Coax z, w M39029/ M39029/ AA, I v, x, y M39029/ M39029/ All others M39029/ M39029/ To meet environmental sealing requirements, size 8 shielded used with this insert arrangement may require separate, non-standard sealing boots that are furnished with the connector. For this insert arrangement, some connector grommet designs use a heat shrink sleeve only with the size 8 shielded to meet environmental sealing requirements. When heat shrink sleeves are used, sealing boots are not used, and when sealing boots are used, heat shrink sleeves are not used. Heat shrink sleeves have a maximum temperature rating of 175 C maximum. When heat shrink sleeves are used, connectors rated to 200 C max are derated to 175 C max. 2. If an identical insert arrangement / contact pattern is required which uses SAE-AS39029/90 and /91 size 8 twinax, use insert arrangement If an identical insert arrangement / contact pattern is required with uses SAE-AS39029/113 and /114 size 8 twinax, use insert arrangement FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 160
166 (INSERT ARRANGEMENT PATTERN ENTICAL TO 25-46, EXCEPT SEALING BOOT IN ACCORDANCE WITH MIL-DTL-38999/62) position s (Insert arrangement 25-47) A (1.65) (13.54) a (10.26) (3.18) B (6.99) (11.84) b (11.10) (0.00) C (10.67) (8.56) c (10.26) (3.18) D (12.45) (5.77) d (7.98) (5.61) E (13.49) (2.36) e (6.22) (8.56) F (13.49) (2.36) f (3.45) (10.77) G (12.45) (5.77) g (0.00) (10.03) H (10.67) (8.56) h (3.45) (10.77) J (6.99) (11.84) k (6.22) (8.56) K (1.65) (13.54) m (7.98) (5.61) L (1.65) (13.54) n (10.26) (3.18) M (6.99) (11.84) p (11.10) (0.00) N (10.67) (8.56) q (10.26) (3.18) P (12.45) (5.77) r (7.98) (5.61) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) USES 161
167 position Shell size s (Insert arrangement 25-47) R (13.49) (2.36) s (6.22) (8.56) S (13.49) (2.36) t (3.45) (10.77) T (12.45) (5.77) u (0.00) (10.03) U (10.67) (8.56) v (2.46) (6.73) V (6.99) (11.84) w (4.57) (0.00) W (1.65) (13.54) x (2.46) (6.73) X (3.45) (10.77) y (2.46) (6.73) Y (6.22) (8.56) z (4.57) (0.00) Z (7.98) (5.61) AA (2.46) (6.73) Arrangement no. Number of Size 8 (see note) Service rating location Standard contact Pin Socket Coax z, w M39029/ M39029/ AA, I v, x, y M39029/ M39029/ All others M39029/ M39029/ NOTE: For this insert arrangement, sealing boots in accordance with MIL-DTL-38999/62 shall be used to environmentally seal the size 8 coax required by this arrangement. Heat shrink sleeves are not used when sealing boots in accordance with MIL-DTL-38999/62 are used. For an identical insert arrangement pattern for connectors supplied with size 8 twinax, see insert arrangement uses size 8 twinax in accordance with SAE-AS39029/113 or /114, and it uses sealing boots in accordance with MIL-DTL-38999/62. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 162
168 position s (Insert arrangement 25-61) A (4.98) (12.70) i (6.38) (7.98) B (7.98) (11.05) j (3.38) (9.63) C (10.49) (8.71) k (0.00) (10.21) D (12.32) (5.84) m (3.38) (9.63) E (13.39) (2.57) n (6.38) (7.98) F (13.61) (0.76) p (8.66) (5.41) G (12.98) (4.17) q (9.96) (2.24) H (11.53) (7.29) r (10.13) (1.17) J (9.35) (9.93) s (9.19) (4.45) K (6.58) (11.94) t (7.24) (7.19) L (3.40) (13.18) u (4.39) (9.22) M (0.00) (13.64) v (0.00) (8.59) N (3.40) (13.18) w (3.73) (5.66) P (6.58) (11.94) x (6.02) (3.10) R (9.35) (9.93) y (6.78) (0.25) S (11.53) (7.29) z (5.79) (3.53) T (12.98) (4.17) AA (3.33) (5.92) U (13.61) (0.76) BB (0.00) (6.78) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 163
169 position MIL-STD-1560C s (Insert arrangement 25-61) V (13.39) (2.57) CC (3.33) (5.92) W (12.32) (5.84) DD (5.79) (3.53) X (10.49) (8.71) EE (6.78) (0.25) Y (7.98) (11.05) FF (6.02) (3.10) Z (4.98) (12.70) GG (3.73) (5.66) a (1.73) (11.53) HH (0.00) (5.08) b (1.73) (11.53) JJ (2.67) (2.39) c (4.39) (9.22) KK (3.43) (1.04) d (7.24) (7.19) LL (0.00) (3.35) e (9.19) (4.45) MM (3.43) (1.04) f (10.13) (1.17) NN (2.67) (2.39) g (9.96) (2.24) PP (0.00) (0.00) h (8.66) (5.41) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 164
170 position (Inactive for new design for MIL-DTL For new design, use arrangement no ) s (Insert arrangement 25-90) A (1.65) (13.54) a (10.26) (3.18) B (6.99) (11.84) b (11.10) (0.00) C (10.67) (8.56) c (10.26) (3.18) D (12.45) (5.77) d (7.98) (5.61) E (13.49) (2.36) e (6.22) (8.56) F (13.49) (2.36) f (3.45) (10.77) G (12.45) (5.77) g (0.00) (10.03) H (10.67) (8.56) h (3.45) (10.77) J (6.99) (11.84) k (6.22) (8.56) K (1.65) (13.54) m (7.98) (5.61) L (1.65) (13.54) n (10.26) (3.18) M (6.99) (11.84) p (11.10) (0.00) N (10.67) (8.56) q (10.26) (3.18) P (12.45) (5.77) r (7.98) (5.61) R (13.49) (2.36) s (6.22) (8.56) S (13.49) (2.36) t (3.45) (10.77) T (12.45) (5.77) u (0.00) (10.03) U (10.67) (8.56) v (2.46) (6.73) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 165
171 position MIL-STD-1560C s (Insert arrangement 25-90) V (6.99) (11.84) w (4.57) (.00) W (1.65) (13.54) x (2.46) (6.73) X (3.45) (10.77) y (2.46) (6.73) Y (6.22) (8.56) z (4.57) (0.00) Z (7.98) (5.61) AA (2.46) (6.73) Shell size Arrangement no Number of Size Service rating location Pin Standard contact Socket 2 8 w, z Twinax (see note) M39029/ M39029/ v, x, y, I AA M39029/ M39029/ All others M39029/ M39029/ NOTE: To meet environmental sealing requirements, size 8 shielded used with this insert arrangement may require separate, non-standard sealing boots that are furnished with the connector. For this insert arrangement, some connector grommet designs use a heat shrink sleeve only with the size 8 shielded to meet environmental sealing requirements. When heat shrink sleeves are used, sealing boots are not used, and when sealing boots are used, heat shrink sleeves are not used. Heat shrink sleeves have a maximum temperature rating of 175 C maximum. When heat shrink sleeves are used, connectors rated to 200 C max are derated to 175 C max. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 166
172 position (INSERT ARRANGEMENT PATTERN ENTICAL TO 25-90, EXCEPT USES SEALING BOOTS IN ACCORDANCE WITH MIL-DTL-38999/62) s (Insert arrangement 25-91) A (1.65) (13.54) a (10.26) (3.18) B (6.99) (11.84) b (11.10) (0.00) C (10.67) (8.56) c (10.26) (3.18) D (12.45) (5.77) d (7.98) (5.61) E (13.49) (2.36) e (6.22) (8.56) F (13.49) (2.36) f (3.45) (10.77) G (12.45) (5.77) g (0.00) (10.03) H (10.67) (8.56) h (3.45) (10.77) J (6.99) (11.84) k (6.22) (8.56) K (1.65) (13.54) m (7.98) (5.61) L (1.65) (13.54) n (10.26) (3.18) M (6.99) (11.84) p (11.10) (0.00) N (10.67) (8.56) q (10.26) (3.18) P (12.45) (5.77) r (7.98) (5.61) R (13.49) (2.36) s (6.22) (8.56) S (13.49) (2.36) t (3.45) (10.77) T (12.45) (5.77) u (0.00) (10.03) U (10.67) (8.56) v (2.46) (6.73) FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 167
173 position s (Insert arrangement 25-91) V (6.99) (11.84) w (4.57) (.00) W (1.65) (13.54) x (2.46) (6.73) X (3.45) (10.77) y (2.46) (6.73) Y (6.22) (8.56) z (4.57) (0.00) Z (7.98) (5.61) AA (2.46) (6.73) Shell size Arrange ment no Number of Size Service rating location Pin Standard contact Socket 2 8 w, z Twinax (see note) M39029/113 M39029/ v, x, y, I AA M39029/ M39029/ All others M39029/ M39029/ NOTE: For this arrangement, sealing boots in accordance with MIL-DTL-38999/62 shall be used to environmentally seal size 8 twinax. Heat shrink sleeves are not used when sealing boots in accordance with MIL-DTL-38999/62 are used. FIGURE 9. Insert arrangement, electrical connector, shell size 25 (series I, III, IV of MIL-DTL-38999, series I of MIL-DTL-27599, and series A of SAE-AS29600) 168
174 position s (Insert arrangement 8-3) location A (1.42) (0.46) B (0.00) (2.01) C (1.42) (0.46) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location M All MS FIGURE 10. Insert arrangement, electrical connector, shell size 8 (series II of MIL-DTL and series II of MIL-DTL-27599). 169
175 position s (Insert arrangement 8-6) location (1.14) (1.98) (1.98) (1.14) (0.00) (2.29) (1.98) (1.14) (1.14) (1.98) (0.00) (0.00) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 10. Insert arrangement, electrical connector, shell size 8 (series II of MIL-DTL and series II of MIL-DTL-27599) 170
176 position s (Insert arrangement 8-35) location (1.14) (1.98) (1.98) (1.14) (0.00) (2.29) (1.98) (1.14) (1.14) (1.98) (0.00) (0.00) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 10. Insert arrangement, electrical connector, shell size 8 (series II of MIL-DTL and series II of MIL-DTL-27599) 171
177 position s (Insert arrangement 8-44) location (0.00) (2.06) (2.03) (0.53) (0.00) (1.27) (2.03) (0.53) (Applicable to MIL-DTL only. Inactive for new design.) Shell Arrangement Number of Size Service Supersedes size no. rating location M All MS FIGURE 10. Insert arrangement, electrical connector, shell size 8 (series II of MIL-DTL and series II of MIL-DTL-27599) 172
178 position s (Insert arrangement 8-98) location A (1.65) (0.97) B (0.00) (1.91) C (1.65) (0.97) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 10. Insert arrangement, electrical connector, shell size 8 (series II of MIL-DTL and series II of MIL-DTL-27599) 173
179 position s (Insert arrangement 10-5) location A (1.65) (1.42) B (2.87) (1.65) C (0.00) (3.30) D (2.87) (1.65) E (1.65) (1.42) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 11. Insert arrangement, electrical connector, shell size 10 (series II of MIL-DTL and series II of MIL-DTL-27599). 174
180 s (Insert arrangement 10-13) position (0.00) (3.71) (3.51) (1.14) (2.16) (3.00) (3.51) (1.14) (3.51) (1.14) (2.16) (3.00) (3.51) (1.14) (0.00) (1.42) (2.16) (3.00) (1.24) (0.89) (0.00) (3.71) (1.24) (0.89) (2.16) (3.00) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 11. Insert arrangement, electrical connector, shell size 10 (series II of MIL-DTL and series II of MIL-DTL-27599) 175
181 s (Insert arrangement 10-35) position (0.00) (3.71) (3.51) (1.14) (2.16) (3.00) (3.51) (1.14) (3.51) (1.14) (2.16) (3.00) (3.51) (1.14) (0.00) (1.42) (2.16) (3.00) (1.24) (0.89) (0.00) (3.71) (1.24) (0.89) (2.16) (3.00) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 11. Insert arrangement, electrical connector, shell size 10 (series II of MIL-DTL and series II of MIL-DTL-27599) 176
182 position s (Insert arrangement 10-98) location A (0.00) (3.30) B (3.30) (0.00) C (1.65) (2.87) D (1.65) (2.87) E (3.30) (0.00) F (0.00) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 11. Insert arrangement, electrical connector, shell size 10 (series II of MIL-DTL and series II of MIL-DTL-27599) 177
183 position s (Insert arrangement 10-99) location A (1.65) (2.87) B (3.30) (0.00) C (1.65) (2.87) D (1.65) (2.87) E (3.30) (0.00) F (1.65) (2.87) G (0.00) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 11. Insert arrangement, electrical connector, shell size 10 (series II of MIL-DTL and series II of MIL-DTL-27599) 178
184 position s (Insert arrangement 12-3) location A (2.39) (1.47) B (0.00) (2.82) C (2.39) (1.47) Shell Arrangement Number of Size Service Supersedes size no. rating location II All MS FIGURE 12. Insert arrangement, electrical connector, shell size 12 (series II of MIL-DTL and series II of MIL-DTL-27599) 179
185 position s (Insert arrangement 12-4) location A (0.00) (3.81) B (3.71) (0.89) C (0.00) (2.11) D (3.71) (0.89) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 12. Insert arrangement, electrical connector, shell size 12 (series II of MIL-DTL and series II of MIL-DTL-27599) 180
186 position s (Insert arrangement 12-8) location A (1.65) (3.99) B (4.32) (0.00) C (3.05) (3.05) D (0.00) (4.32) E (3.05) (3.05) F (4.32) (0.00) G (1.65) (3.99) H (0.00) (1.12) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 12. Insert arrangement, electrical connector, shell size 12 (series II of MIL-DTL and series II of MIL-DTL-27599) 181
187 s (Insert arrangement 12-22) position (1.14) (5.00) (4.62) (2.24) (3.20) (4.01) (3.20) (4.01) (4.62) (2.24) (1.14) (5.00) (5.16) (0.00) (1.14) (2.72) (4.62) (2.24) (2.97) (0.66) (3.20) (4.01) (2.36) (1.91) (1.14) (5.00) (0.00) (3.05) (1.14) (5.00) (2.36) (1.91) (3.20) (4.01) (2.97) (0.66) (4.62) (2.24) (1.14) (2.72) (5.16) (0.00) (0.00) (0.76) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 12. Insert arrangement, electrical connector, shell size 12 (series II of MIL-DTL and series II of MIL-DTL-27599). 182
188 position s (Insert arrangement 12-35) (1.14) (5.00) (4.62) (2.24) (3.20) (4.01) (3.20) (4.01) (4.62) (2.24) (1.14) (5.00) (5.16) (0.00) (1.14) (2.72) (4.62) (2.24) (2.97) (0.66) (3.20) (4.01) (2.36) (1.91) (1.14) (5.00) (0.00) (3.05) (1.14) (5.00) (2.36) (1.91) (3.20) (4.01) (2.97) (0.66) (4.62) (2.24) (1.24) (2.72) (5.16) (0.00) (0.00) (0.76) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 12. Insert arrangement, electrical connector, shell size 12 (series II of MIL-DTL and series II of MIL-DTL-27599) 183
189 s (Insert arrangement 12-98) position A (0.00) (4.95) F (4.17) (2.67) B (3.18) (3.81) G (4.90) (0.76) C (4.90) (0.76) H (3.18) (3.81) D (4.17) (2.67) J (1.65) (0.38) E (0.00) (3.43) K (1.65) (0.38) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 12. Insert arrangement, electrical connector, shell size 12 (series II of MIL-DTL and series II of MIL-DTL-27599) 184
190 position s (Insert arrangement 14-5) location A (0.00) (2.54) B (4.42) (0.61) C (2.39) (3.76) D (2.39) (3.76) E (4.42) (0.61) Shell Arrangement Number of Size Service Supersedes size no. rating location II All MS FIGURE 13. Insert arrangement, electrical connector, shell size 14 (series II of MIL-DTL and series II of MIL-DTL-27599). 185
191 s (Insert arrangement 14-15) A (2.54) (5.72) J (6.20) (0.36) B (5.13) (3.56) K (5.13) (3.56) C (6.20) (0.36) L (2.54) (5.72) D (5.54) (2.87) M (0.00) (3.56) E (3.20) (5.31) N (2.79) (1.02) F (0.00) (6.22) P (0.00) (1.96) G (3.20) (5.18) R (2.79) (1.02) H (5.54) (2.87) Shell size Arrangement no Number of Size Service rating I location P All others Supersedes MS FIGURE 13. Insert arrangement, electrical connector, shell size 14 (series II of MIL-DTL and series II of MIL-DTL-27599) 186
192 s (Insert arrangement 14-18) A (1.65) (6.40) K (4.95) (2.87) B (4.95) (2.87) L (1.65) (6.40) C (6.60) (0.00) M (1.65) (2.87) D (4.95) (2.87) N (1.65) (2.87) E (3.30) (5.72) P (3.30) (0.00) F (0.00) (5.72) R (1.65) (2.87) G (3.30) (5.72) S (1.65) (2.87) H (4.95) (2.87) T (3.30) (0.00) J (6.60) (0.00) U (0.00) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 13. Insert arrangement, electrical connector, shell size 14 (series II of MIL-DTL and series II of MIL-DTL-27599) 187
193 s (Insert arrangement 14-35) (1.14) (6.65) (3.12) (3.02) (3.12) (5.51) (4.32) (1.02) (5.36) (4.06) (4.32) (1.27) (6.45) (2.03) (3.12) (3.23) (6.76) (0.25) (1.14) (4.37) (6.27) (2.49) (1.14) (4.37) (5.08) (4.45) (3.12) (3.23) (3.30) (5.89) (4.32) (1.27) (1.14) (6.65) (4.32) (1.02) (1.14) (6.65) (3.12) (3.02) (3.30) (5.89) (1.14) (4.37) (5.08) (4.45) (1.14) (1.88) (6.27) (2.49) (2.29) (0.10) (6.76) (0.25) (1.14) (2.08) (6.45) (2.03) (1.14) (2.08) (5.36) (4.06) (2.29) (0.10) (3.12) (5.51) (1.14) (1.88) (1.14) (6.65) (0.00) (0.10) (1.14) (4.37) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 13. Insert arrangement, electrical connector, shell size 14 (series II of MIL-DTL and series II of MIL-DTL-27599) 188
194 s (Insert arrangement 14-37) (1.14) (6.65) (3.12) (3.02) (3.12) (5.51) (4.32) (1.02) (5.36) (4.06) (4.32) (1.27) (6.45) (2.03) (3.12) (3.23) (6.76) (0.25) (1.14) (4.37) (6.27) (2.49) (1.14) (4.37) (5.08) (4.45) (3.12) (3.23) (3.30) (5.89) (4.32) (1.27) (1.14) (6.65) (4.32) (1.02) (1.14) (6.65) (3.12) (3.02) (3.30) (5.89) (1.14) (4.37) (5.08) (4.45) (1.14) (1.88) (6.27) (2.49) (2.29) (0.10) (6.76) (0.25) (1.14) (2.08) (6.45) (2.03) (1.14) (2.08) (5.36) (4.06) (2.29) (0.10) (3.12) (5.51) (1.14) (1.88) (1.14) (6.65) (0.00) (0.10) (1.14) (4.37) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 13. Insert arrangement, electrical connector, shell size 14 (series II of MIL-DTL and series II of MIL-DTL-27599) 189
195 s (Insert arrangement 14-97) A (1.65) (5.94) G (5.26) (2.41) B (4.52) (4.52) H (5.94) (1.65) C (5.84) (0.58) J (4.52) (4.52) D (4.52) (4.52) K (1.65) (5.94) E (1.65) (5.94) L (1.19) (2.06) F (2.26) (5.97) M (1.19) (2.06) Shell size Arrangement no Number of Size Service rating I location C,M,G,L All others Supersedes MS FIGURE 13. Insert arrangement, electrical connector, shell size 14 (series II of MIL-DTL and series II of MIL-DTL-27599) 190
196 position s (Insert arrangement 16-6 or 16-7) location A (3.07) (5.31) B (6.12) (0.00) C (0.00) (6.12) D (6.12) (0.00) E (3.07) (5.31) F (0.00) (0.00) Shell size 16 Arrangement no. Number of Size Service rating location Supersedes I All MS Shielded, size 12A II All FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 191
197 s (Insert arrangement 16-8) A (0.00) (5.99) E (2.39) (5.49) B (3.25) (2.18) F (5.84) (1.98) C (5.84) (1.98) G (3.25) (2.18) D (2.39) (5.49) H (0.00) (1.32) Shell Arrangement Number of Size Service Supersedes size no. rating location II All MS FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599). 192
198 s (Insert arrangement 16-26) A (0.00) (8.15) P (6.07) (5.44) B (3.33) (7.44) R (3.33) (7.44) C (6.07) (5.44) S (1.78) (4.50) D (7.75) (2.51) T (1.78) (4.50) E (8.10) (0.86) U (4.45) (2.39) F (7.06) (4.09) V (4.52) (0.91) G (4.80) (6.60) W (3.02) (3.84) H (1.70) (7.98) X (.00) (5.16) J (1.70) (7.98) Y (.005) (3.84) K (4.80) (6.60) Z (4.52) (0.91) L (7.06) (4.09) a (4.45) (2.39) M (8.10) (0.86) b (0.00) (1.65) N (7.75) (2.51) c (0.00) (1.65) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 193
199 s (Insert arrangement 16-35) (7.92) (2.18) (0.00) (2.39) (7.92) (0.10) (0.00) (4.67) (7.92) (2.39) (0.00) (6.96) (6.15) (5.61) (2.26) (8.03) (5.94) (3.33) (1.98) (5.61) (5.94) (1.04) (1.98) (3.33) (5.94) (1.24) (1.98) (1.04) (5.94) (3.53) (1.98) (1.24) (5.94) (5.82) (1.98) (3.53) (4.37) (7.09) (1.98) (5.82) (3.96) (4.47) (1.98) (8.10) (3.96) (2.18) (4.37) (7.09) (3.96) (0.10) (3.96) (4.47) (3.96) (2.39) (3.96) (2.18) (3.96) (4.67) (3.96) (0.10) FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 194
200 s (Insert arrangement 16-35) (3.96) (6.96) (3.96) (2.39) (2.26) (8.03) (3.96) (4.67) (1.98) (5.61) (3.96) (6.96) (1.98) (3.33) (6.15) (5.61) (1.98) (1.04) (5.94) (3.33) (1.98) (1.24) (5.94) (1.04) (1.98) (3.53) (5.94) (1.24) (1.98) (5.82) (5.94) (3.53) (1.98) (8.10) (5.94) (5.82) (0.00) (8.36) (7.92) (2.18) (0.00) (4.47) (7.92) (0.10) (0.00) (2.18) (7.92) (2.39) (0.00) (0.10) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 195
201 s (Insert arrangement 16-42) (1.27) (8.08) (2.41) (5.03) (3.68) (7.26) (4.52) (3.61) (5.79) (5.84) (5.54) (1.27) (7.29) (3.78) (5.54) (1.27) (8.08) (1.35) (4.50) (3.61) (8.10) (1.19) (2.41) (5.13) (7.34) (3.63) (0.00) (5.97) (5.89) (5.74) (2.41) (5.13) (3.84) (7.24) (4.50) (3.61) (1.42) (8.08) (5.54) (1.27) (1.42) (8.08) (5.54) (1.27) (3.84) (7.24) (4.52) (3.61) (5.89) (5.74) (2.41) (5.03) (7.34) (3.63) (0.00) (3.33) (8.10) (1.19) (2.31) (2.03) (8.08) (1.35) (3.07) (0.43) (7.29) (3.78) (1.42) (2.57) (5.79) (5.84) (1.42) (2.57) FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 196
202 Shell size s (Insert arrangement 16-42) (3.68) (7.26) (3.07) (0.43) (1.27) (8.08) (2.31) (2.03) (0.00) (5.87) (0.00) (0.79) Arrangement no. (Applicable to MIL-DTL only. Inactive for new design) Number of Size Service rating location Supersedes M All MS FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 197
203 s (Insert arrangement 16-55) (7.92) (2.18) (0.00) (2.39) (7.92) (0.10) (0.00) (4.67) (7.92) (2.39) (0.00) (6.96) (6.15) (5.61) (2.26) (8.03) (5.94) (3.33) (1.98) (5.61) (5.94) (1.04) (1.98) (3.33) (5.94) (1.24) (1.98) (1.04) (5.94) (3.53) (1.98) (1.24) (5.94) (5.82) (1.98) (3.53) (4.37) (7.09) (1.98) (5.82) (3.96) (4.47) (1.98) (8.10) FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 198
204 Shell size s (Insert arrangement 16-55) (3.96) (2.18) (4.37) (7.09) (3.96) (0.10) (3.96) (4.47) (3.96) (2.39) (3.96) (2.18) (3.96) (4.67) (3.96) (0.10) (3.96) (6.96) (3.96) (2.39) (2.26) (8.03) (3.96) (4.67) (1.98) (5.61) (3.96) (6.96) (1.98) (3.33) (6.15) (5.61) (1.98) (1.04) (5.94) (3.33) (1.98) (1.24) (5.94) (1.04) (1.98) (3.53) (5.94) (1.24) (1.98) (5.82) (5.94) (3.53) (1.98) (8.10) (5.94) (5.82) (0.00) (8.36) (7.92) (2.18) (0.00) (4.47) (7.92) (0.10) (0.00) (2.18) (7.92) (2.39) (0.00) (0.10) Arrangement no. (Inactive for new design for MIL-DTL-38999) Number of Size Service rating location Supersedes M M All MS FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 199
205 s (Insert arrangement 16-99) A (0.00) (8.15) N (7.75) (2.51) B (3.33) (7.44) P (6.07) (5.44) C (6.07) (5.44) R (3.33) (7.44) D (7.75) (2.51) S (1.78) (4.50) E (8.10) (0.86) T (1.78) (4.50) F (7.06) (4.09) U (4.45) (2.39) G (4.80) (6.60) V (3.81) (1.91) H (1.70) (7.98) W (0.00) (4.09) J (1.70) (7.98) X (3.81) (1.91) K (4.80) (6.60) Y (4.45) (2.39) L (7.06) (4.09) Z (0.00) (0.64) M (8.10) (0.86) Shell size Arrangement no Number of Size Service rating location 2 16 W, Z I All others Supersedes MS FIGURE 14. Insert arrangement, electrical connector, shell size 16 (series II of MIL-DTL and series II of MIL-DTL-27599) 200
206 s (Insert arrangement 18-11) A (2.67) (6.60) G (6.99) (1.35) B (6.35) (3.35) H (6.35) (3.35) C (6.99) (1.35) J (2.67) (6.60) D (4.55) (5.46) K (0.00) (2.67) E (0.00) (7.14) L (0.00) (2.34) F (4.55) (5.46) Shell Arrangement Number of Size Service Supersedes size no. rating location II All MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599). 201
207 s (Insert arrangement 18-28) A (1.68) (8.97) R (7.26) (5.51) B (4.80) (7.75) S (4.80) (7.75) C (7.26) (5.51) T (1.68) (8.97) D (8.76) (2.49) U (0.00) (5.84) E (9.07) (0.84) V (3.15) (4.90) F (8.15) (4.06) W (5.31) (2.41) G (6.15) (6.73) X (5.79) (0.84) H (3.30) (8.51) Y (4.42) (3.84) J (0.00) (9.12) Z (0.00) (4.85) K (3.30) (8.51) a (4.42) (3.84) L (6.15) (6.73) b (5.79) (0.84) FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 202
208 s (Insert arrangement 18-28) M (8.15) (4.06) c (5.31) (2.41) N (9.07) (0.84) d (3.15) (4.90) P (8.76) (2.49) e (0.00) (1.57) Shell size Arrangement no Number of Size Service rating location e, Z 2 16 I All others Supersedes MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 203
209 s (Insert arrangement 18-30) A (1.65) (8.79) S (1.65) (8.79) B (4.72) (7.59) T (2.13) (5.51) C (7.16) (5.33) U (4.60) (3.28) D (8.64) (2.36) V (5.79) (0.20) E (8.92) (0.84) W (4.90) (2.97) F (8.00) (4.01) X (2.44) (5.16) G (5.99) (6.63) Y (0.00) (7.37) H (3.15) (8.38) Z (2.44) (5.16) J (3.15) (8.38) a (4.90) (2.97) K (5.99) (6.63) b (5.79) (0.20) L (8.00) (4.01) c (4.60) (3.28) M (8.92) (0.84) d (2.13) (5.51) FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 204
210 s (Insert arrangement 18-30) N (8.64) (2.36) e (0.00) (1.83) P (7.16) (5.33) f (1.75) (1.93) R (4.72) (7.59) g (1.75) (1.93) Shell size Arrangement no Number of Size Service rating location 1 16 e I All others Supersedes MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 205
211 s (Insert arrangement 18-32) A (1.68) (8.97) T (1.68) (8.97) B (4.80) (7.75) U (0.00) (5.84) C (7.26) (5.51) V (3.15) (4.90) D (8.76) (2.49) W (5.31) (2.41) E (9.07) (0.84) X (5.79) (0.84) F (8.15) (4.06) Y (4.42) (3.84) G (6.15) (6.73) Z (1.65) (5.61) H (3.30) (8.51) a (1.65) (5.61) J (0.00) (9.12) b (4.42) (3.84) K (3.30) (8.51) c (5.79) (0.84) L (6.15) (6.73) d (5.31) (2.41) M (8.15) (4.06) e (3.15) (4.90) N (9.07) (0.84) f (0.00) (2.44) FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 206
212 s (Insert arrangement 18-32) P (8.76) (2.49) g (2.44) (0.00) R (7.26) (5.51) h (0.00) (2.44) S (4.80) (7.75) j (2.44) (0.00) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 207
213 s (Insert arrangement 18-35) (9.07) (2.29) (1.14) (9.14) (9.07) (0.00) (1.14) (6.86) (9.07) (2.29) (1.14) (4.57) (7.09) (5.72) (1.14) (2.29) (7.09) (3.43) (1.14) (0.00) (7.09) (1.14) (1.14) (2.29) (7.09) (1.14) (1.14) (4.57) (7.09) (3.43) (1.14) (6.86) (7.09) (5.72) (1.14) (9.14) (5.11) (6.86) (3.12) (8.00) (5.11) (4.57) (3.12) (5.72) (5.11) (2.29) (3.12) (3.43) (5.11) (0.00) (3.12) (1.14) (5.11) (2.29) (3.12) (1.14) (5.11) (4.57) (3.12) (3.43) FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 208
214 s (Insert arrangement 18-35) (5.11) (6.86) (3.12) (5.72) (3.12) (8.00) (3.12) (8.00) (3.12) (5.72) (5.11) (6.86) (3.12) (3.43) (5.11) (4.57) (3.12) (1.14) (5.11) (2.29) (3.12) (1.14) (5.11) (0.00) (3.12) (3.43) (5.11) (2.29) (3.12) (5.72) (5.11) (4.57) (3.12) (8.00) (5.11) (6.86) (1.14) (9.14) (7.09) (5.72) (1.14) (6.86) (7.09) (3.43) (1.14) (4.57) (7.09) (1.14) (1.14) (2.29) (7.09) (1.14) (1.14) (0.00) (7.09) (3.43) (1.14) (2.29) (7.09) (5.72) (1.14) (4.57) (9.07) (2.29) (1.14) (6.86) (9.07) (0.00) (1.14) (9.14) (9.07) (2.29) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 209
215 s (Insert arrangement 18-45) (9.07) (2.06) (2.24) (9.14) (9.07) (0.23) (1.14) (6.63) (9.07) (2.51) (1.14) (4.34) (7.72) (5.41) (1.14) (2.06) (7.09) (3.20) (1.14) (0.23) (7.09) (0.91) (1.14) (2.51) (7.09) (1.37) (1.14) (4.80) (7.09) (3.66) (1.14) (7.09) (7.09) (5.94) (1.14) (9.37) (6.20) (7.11) (3.96) (7.65) (5.11) (4.34) (3.12) (5.49) (5.11) (2.06) (3.12) (3.20) (5.11) (0.23) (3.12) (0.91) (5.11) (2.51) (3.12) (1.37) (5.11) (4.80) (3.12) (3.66) (5.11) (7.09) (3.12) (5.94) FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 210
216 s (Insert arrangement 18-45) (3.96) (7.65) (3.12) (8.23) (3.12) (5.49) (6.20) (7.11) (3.12) (3.20) (5.11) (4.34) (3.12) (0.91) (5.11) (2.06) (3.12) (1.37) (5.11) (0.23) (3.12) (3.66) (5.11) (2.51) (3.12) (5.94) (5.11) (4.80) (3.12) (8.23) (5.11) (7.09) (2.24) (9.14) (7.72) (5.41) (0.00) (8.61) (7.09) (3.20) (1.14) (6.63) (7.09) (0.91) (1.14) (4.34) (7.09) (1.37) (1.14) (2.06) (7.09) (3.66) (1.14) (0.23) (7.09) (5.94) (1.14) (2.51) (9.07) (2.06) (1.14) (4.80) (9.07) (0.23) (1.14) (7.09) (9.07) (2.51) (1.14) (9.37) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 211
217 s (Insert arrangement 18-53) (1.27) (9.25) (6.76) (0.46) (3.71) (8.53) (6.60) (2.39) (5.89) (7.21) (4.67) (4.95) (7.65) (5.38) (2.51) (6.40) (8.81) (3.12) (0.00) (6.81) (9.32) (0.64) (2.51) (6.40) (9.14) (1.91) (4.67) (4.95) (8.33) (4.32) (6.60) (2.39) (6.83) (6.38) (6.76) (0.46) (4.85) (7.98) (6.22) (2.95) (2.51) (8.99) (4.65) (4.95) (0.00) (9.35) (2.44) (6.30) (2.51) (8.99) (0.00) (4.47) (4.85) (7.98) (2.44) (3.68) (6.83) (6.38) (4.01) (1.73) (8.33) (4.32) (4.52) (0.81) FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 212
218 s (Insert arrangement 18-53) (9.14) (1.91) (3.05) (2.90) (9.32) (0.64) (0.00) (4.27) (8.81) (3.12) (3.05) (2.90) (7.65) (5.38) (4.52) (0.81) (5.89) (7.21) (4.01) (1.73) (3.71) (8.53) (2.44) (3.68) (1.27) (9.25) (0.00) (1.93) (0.00) (7.01) (2.03) (0.05) (2.44) (6.30) (0.00) (1.73) (4.65) (4.95) (2.03) (0.05) (6.22) (2.95) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M All MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 213
219 s (Insert arrangement 18-66) (9.07) (2.29) (1.14) (9.14) (9.07) (0.00) (1.14) (6.86) (9.07) (2.29) (1.14) (4.57) (7.09) (5.72) (1.14) (2.29) (7.09) (3.43) (1.14) (0.00) (7.09) (1.14) (1.14) (2.29) (7.09) (1.14) (1.14) (4.57) (7.09) (3.43) (1.14) (6.86) (7.09) (5.72) (1.14) (9.14) (5.11) (6.86) (3.12) (8.00) (5.11) (4.57) (3.12) (5.72) (5.11) (2.29) (3.12) (3.43) (5.11) (0.00) (3.12) (1.14) (5.11) (2.29) (3.12) (1.14) (5.11) (4.57) (3.12) (3.43) (5.11) (6.86) (3.12) (5.72) FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 214
220 s (Insert arrangement 18-66) (3.12) (8.00) (3.12) (8.00) (3.12) (5.72) (5.11) (6.86) (3.12) (3.43) (5.11) (4.57) (3.12) (1.14) (5.11) (2.29) (3.12) (1.14) (5.11) (0.00) (3.12) (3.43) (5.11) (2.29) (3.12) (5.72) (5.11) (4.57) (3.12) (8.00) (5.11) (6.86) (1.14) (9.14) (7.09) (5.72) (1.14) (6.86) (7.09) (3.43) (1.14) (4.57) (7.09) (1.14) (1.14) (2.29) (7.09) (1.14) (1.14) (0.00) (7.09) (3.43) (1.14) (2.29) (7.09) (5.72) (1.14) (4.57) (9.07) (2.29) (1.14) (6.86) (9.07) (0.00) (1.14) (9.14) (9.07) (2.29) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 215
221 s (Insert arrangement 18-67) (9.07) (2.06) (2.24) (9.14) (9.07) (0.23) (1.14) (6.63) (9.07) (2.51) (1.14) (4.34) (7.72) (5.41) (1.14) (2.06) (7.09) (3.20) (1.14) (0.23) (7.09) (0.91) (1.14) (2.51) (7.09) (1.37) (1.14) (4.80) (7.09) (3.66) (1.14) (7.09) (7.09) (5.94) (1.14) (9.37) (6.20) (7.11) (3.96) (7.65) (5.11) (4.34) (3.12) (5.49) (5.11) (2.06) (3.12) (3.20) (5.11) (0.23) (3.12) (0.91) (5.11) (2.51) (3.12) (1.37) (5.11) (4.80) (3.12) (3.66) FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 216
222 s (Insert arrangement 18-67) (5.11) (7.09) (3.12) (5.94) (3.96) (7.65) (3.12) (8.23) (3.12) (5.49) (6.20) (7.11) (3.12) (3.20) (5.11) (4.34) (3.12) (0.91) (5.11) (2.06) (3.12) (1.37) (5.11) (0.23) (3.12) (3.66) (5.11) (2.51) (3.12) (5.94) (5.11) (4.80) (3.12) (8.23) (5.11) (7.09) (2.24) (9.14) (7.72) (5.41) (0.00) (8.61) (7.09) (3.20) (1.14) (6.63) (7.09) (0.91) (1.14) (4.34) (7.09) (1.37) (1.14) (2.06) (7.09) (3.66) (1.14) (0.23) (7.09) (5.94) (1.14) (2.51) (9.07) (2.06) (1.14) (4.80) (9.07) (0.23) (1.14) (7.09) (9.07) (2.51) (1.14) (9.37) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 217
223 s (Insert arrangement 18-96) A (0.00) (7.65) F (5.41) (5.41) B (5.41) (5.41) G (7.65) (0.00) C (7.65) (0.00) H (5.41) (5.41) D (5.41) (5.41) J (0.00) (0.00) E (0.00) (7.65) Shell size Arrangement no. Number of Size Service rating location I All FIGURE 15. Insert arrangement, electrical connector, shell size 18 (series II of MIL-DTL and series II of MIL-DTL-27599) 218
224 s (Insert arrangement 20-1) (1.35) (10.82) (2.49) (8.18) (3.71) (10.26) (4.67) (7.11) (5.89) (9.19) (6.55) (5.59) (7.77) (7.67) (7.90) (3.58) (9.27) (5.77) (8.43) (1.22) (10.31) (3.58) (8.43) (1.22) (10.85) (1.22) (7.90) (3.58) (10.85) (1.22) (6.55) (5.59) (10.31) (3.58) (4.67) (7.11) (9.27) (5.77) (2.49) (8.18) (7.77) (7.67) (1.22) (6.12) (5.89) (9.19) (1.22) (6.12) (3.71) (10.26) (3.40) (5.05) (1.35) (10.82) (5.28) (3.53) (1.35) (10.82) (6.02) (1.22) FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599). 219
225 MIL-STD-1560C s (Insert arrangement 20-1) (3.71) (10.26) (6.02) (1.22) (5.89) (9.19) (5.28) (3.53) (7.77) (7.67) (3.40) (5.05) (9.27) (5.77) (1.22) (6.12) (10.31) (3.58) (1.22) (6.12) (10.85) (1.22) (3.40) (5.05) (10.85) (1.22) (5.28) (3.53) (10.31) (3.58) (6.02) (1.22) (9.27) (5.77) (6.02) (1.22) (7.77) (7.67) (5.28) (3.53) (5.89) (9.19) (3.40) (5.05) (3.71) (10.26) (1.22) (3.71) (1.35) (10.82) (1.22) (3.71) (0.00) (8.20) (3.18) (2.29) (2.49) (8.18) (3.94) (0.00) (4.67) (7.11) (3.18) (2.29) (6.55) (5.59) (1.22) (3.71) (7.90) (3.58) (1.22) (3.71) (8.43) (1.22) (3.18) (2.29) (8.43) (1.22) (3.94) (0.00) (7.90) (3.58) (3.18) (2.29) (6.55) (5.59) (0.00) (1.35) (4.67) (7.11) (1.22) (0.74) (2.49) (8.18) (1.22) (0.74) (0.00) (8.81) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 220
226 s (Insert arrangement 20-2) (1.32) (10.77) (4.19) (6.93) (3.91) (10.13) (1.35) (8.41) (6.25) (8.84) (1.35) (8.41) (8.28) (7.11) (4.19) (6.93) (9.70) (4.85) (6.40) (5.33) (10.59) (2.34) (7.75) (3.02) (10.80) (.33) (8.13) (0.38) (10.41) (2.97) (7.92) (2.29) (9.40) (5.44) (6.96) (4.78) (7.82) (7.59) (4.93) (6.50) (5.69) (9.19) (2.59) (7.80) (3.25) (10.29) (0.00) (5.77) (0.00) (10.72) (2.59) (5.13) (3.25) (10.29) (4.65) (3.43) (5.69) (9.19) (5.59) (0.94) (7.82) (7.59) (5.41) (1.73) (9.40) (5.44) (4.01) (4.01) (10.41) (2.97) (1.83) (5.69) (10.80) (0.33) (1.83) (5.69) FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 221
227 s (Insert arrangement 20-2) (10.59) (2.34) (4.01) (4.01) (9.70) (4.85) (5.41) (1.73) (8.28) (7.11) (5.59) (0.94) (6.25) (8.84) (4.65) (3.43) (3.91) (10.13) (2.59) (5.13) (1.32) (10.77) (0.00) (3.10) (0.00) (8.43) (2.41) (1.91) (2.59) (7.80) (2.92) (0.74) (4.93) (6.50) (1.42) (3.05) (6.96) (4.78) (1.42) (3.05) (7.92) (2.29) (2.92) (0.74) (8.13) (0.38) (2.41) (1.91) (7.75) (3.02) (0.00) (0.74) (6.40) (5.33) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M All MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 222
228 s (Insert arrangement 20-16) A (3.00) (8.18) J (8.66) (0.91) B (6.88) (5.36) K (6.88) (5.36) C (8.66) (0.91) L (3.00) (8.18) D (7.82) (3.81) M (0.00) (4.45) E (4.62) (7.37) N (3.91) (1.57) F (0.00) (8.71) P (2.39) (3.10) G (4.62) (7.37) R (2.39) (3.10) H (7.82) (3.81) S (3.91) (1.57) Shell Arrangement Number of Size Service Supersedes size no. rating location II All MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 223
229 s (Insert arrangement 20-24) A (4.45) (9.53) N (3.81) (5.08) B (8.89) (5.08) P (6.35) (0.00) C (10.16) (0.00) R (5.08) (3.81) D (8.89) (5.08) S (1.91) (6.35) E (5.08) (8.89) T (1.91) (6.35) F (0.00) (10.16) U (5.08) (3.81) G (5.08) (8.89) V (6.35) (0.00) H (8.89) (5.08) W (3.81) (5.08) J (10.16) (0.00) X (0.00) (3.81) K (8.89) (5.08) Y (2.54) (0.64) L (4.45) (9.53) Z (0.00) (2.54) M (0.00) (7.62) a (2.54) (.64) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 224
230 s (Insert arrangement 20-25) A (0.00) (10.16) P (5.72) (5.72) B (3.81) (9.53) R (3.81) (9.53) C (5.72) (5.72) S (1.91) (5.72) D (9.53) (4.45) T (6.35) (1.91) E (10.16) (0.64) U (3.81) (5.08) F (9.53) (3.18) V (3.81) (5.08) G (6.99) (7.62) W (6.35) (1.91) H (2.54) (10.16) X (1.91) (5.72) J (2.54) (10.16) Y (0.00) (1.91) K (6.99) (7.62) Z (3.18) (0.64) L (9.53) (3.18) a (0.00) (3.18) M (10.16) (0.64) b (3.18) (0.64) N (9.53) (4.45) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 225
231 s (Insert arrangement 20-27) A (0.00) (10.16) R (3.81) (9.53) B (3.81) (9.53) S (3.18) (5.72) C (6.99) (6.99) T (5.72) (2.54) D (9.53) (3.81) U (6.35) (1.27) E (10.16) (0.00) V (3.81) (5.08) F (9.53) (3.81) W (0.00) (6.35) G (6.99) (7.62) X (3.81) (5.08) H (2.54) (10.16) Y (6.35) (1.27) J (2.54) (10.16) Z (5.72) (2.54) K (6.99) (7.62) a (3.18) (5.72) L (9.53) (3.81) b (0.00) (2.54) M (10.16) (0.00) c (2.54) (0.64) N (9.53) (3.81) d (2.54) (0.64) P (6.99) (6.99) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 226
232 s (Insert arrangement 20-35) (1.35) (10.82) (2.49) (8.18) (3.71) (10.26) (4.67) (7.11) (5.89) (9.19) (6.55) (5.59) (7.77) (7.67) (7.90) (3.58) (9.27) (5.77) (8.43) (1.22) (10.31) (3.58) (8.43) (1.22) (10.85) (1.22) (7.90) (3.58) (10.85) (1.22) (6.55) (5.59) (10.31) (3.58) (4.67) (7.11) (9.27) (5.77) (2.49) (8.18) (7.77) (7.67) (1.22) (6.12) (5.89) (9.19) (1.22) (6.12) (3.71) (10.26) (3.40) (5.05) (1.35) (10.82) (5.28) (3.53) (1.35) (10.82) (6.02) (1.22) (3.71) (10.26) (6.02) (1.22) FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 227
233 s (Insert arrangement 20-35) (5.89) (9.19) (5.28) (3.53) (7.77) (7.67) (3.40) (5.05) (9.27) (5.77) (1.22) (6.12) (10.31) (3.58) (1.22) (6.12) (10.85) (1.22) (3.40) (5.05) (10.85) (1.22) (5.28) (3.53) (10.31) (3.58) (6.02) (1.22) (9.27) (5.77) (6.02) (1.22) (7.77) (7.67) (5.28) (3.53) (5.89) (9.19) (3.40) (5.05) (3.71) (10.26) (1.22) (3.71) (1.35) (10.82) (1.22) (3.71) (0.00) (8.20) (3.18) (2.29) (2.49) (8.18) (3.94) (0.00) (4.67) (7.11) (3.18) (2.29) (6.55) (5.59) (1.22) (3.71) (7.90) (3.58) (1.22) (3.71) (8.43) (1.22) (3.18) (2.29) (8.43) (1.22) (3.94) (0.00) (7.90) (3.58) (3.18) (2.29) (6.55) (5.59) (0.00) (1.35) (4.67) (7.11) (1.22) (0.74) (2.49) (8.18) (1.22) (0.74) (0.00) (8.81) (Applicable to MIL-DTL only) Shell Arrangement Number of Size Service Supersedes size no. rating location D M All MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 228
234 s (Insert arrangement 20-39) A (1.65) (10.44) X (0.00) (7.49) B (4.80) (9.42) Y (3.20) (6.50) C (7.47) (7.49) Z (5.89) (4.55) D (9.42) (4.80) a (7.11) (1.45) E (10.44) (1.65) b (7.11) (1.88) F (10.44) (1.65) c (5.51) (4.80) G (9.42) (4.80) d (2.84) (6.73) H (7.47) (7.47) e (2.84) (6.73) J (4.80) (9.42) f (5.51) (4.80) K (1.65) (10.44) g (7.11) (1.88) L (1.65) (10.44) h (7.11) (1.45) M (4.80) (9.42) i (5.89) (4.55) N (7.47) (7.47) j (3.20) (6.50) P (9.42) (4.80) k (0.00) (4.17) R (10.44) (1.65) m (2.90) (1.22) FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 229
235 MIL-STD-1560C s (Insert arrangement 20-39) S (10.44) (1.65) n (2.69) (2.72) T (9.42) (4.80) p (0.00) (4.80) U (7.47) (7.49) q (2.69) (2.72) V (4.80) (9.42) r (2.90) (1.22) W (1.65) (10.44) Shell size Arrangement no Number of Size Service rating location 2 16 m, r I All others Supersedes MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 230
236 Inches mm Insert arrangement (20-41) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 16. Insert arrangement, electrical connector, shell size 20 (series II of MIL-DTL and series II of MIL-DTL-27599) 231
237 s (Insert arrangement 22-1) (10.87) (6.12) (0.00) (1.19) (11.86) (3.91) (0.00) (3.61) (12.40) (1.55) (0.00) (6.02) (10.54) (0.00) (0.00) (8.43) (12.40) (1.55) (0.00) (10.85) (10.87) (3.61) (2.11) (12.07) (10.87) (6.02) (2.11) (9.65) (8.43) (8.46) (2.11) (7.24) (8.43) (6.05) (2.11) (4.83) (8.43) (3.63) (2.11) (2.41) (8.43) (1.22) (2.11) (0.00) (8.43) (1.19) (2.11) (2.41) (8.43) (3.61) (2.11) (4.83) (8.43) (6.02) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (6.32) (9.65) (2.11) (12.07) (6.32) (7.24) (4.22) (10.87) FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599). 232
238 MIL-STD-1560C s (Insert arrangement 22-1) (6.32) (4.83) (4.22) (8.46) (6.32) (2.41) (4.22) (6.05) (6.32) (0.00) (4.22) (3.63) (6.32) (2.41) (4.22) (1.22) (6.32) (4.83) (4.22) (1.19) (6.32) (7.24) (4.22) (3.61) (6.32) (9.65) (4.22) (6.02) (4.22) (10.87) (4.22) (8.43) (4.22) (8.46) (4.22) (10.85) (4.22) (6.05) (6.32) (9.65) (4.22) (3.63) (6.32) (7.24) (4.22) (1.22) (6.32) (4.83) (4.22) (1.19) (6.32) (2.41) (4.22) (3.61) (6.32) (0.00) (4.22) (6.02) (6.32) (2.41) (4.22) (8.43) (6.32) (4.83) (4.22) (10.85) (6.32) (7.24) (2.11) (12.07) (6.32) (9.65) (2.11) (9.65) (8.43) (8.46) (2.11) (7.24) (8.43) (6.05) (2.11) (4.83) (8.43) (3.63) (2.11) (2.41) (8.43) (1.22) (2.11) (0.00) (8.43) (1.19) (2.11) (2.41) (8.43) (3.61) (2.11) (4.83) (8.43) (6.02) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (10.87) (6.12) (2.11) (12.07) (11.86) (3.91) (0.00) (10.87) (12.40) (1.55) (0.00) (8.46) (10.54) (0.00) FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 233
239 Shell size s (Insert arrangement 22-1) (0.00) (6.05) (12.40) (1.55) (0.00) (3.63) (10.87) (3.61) (0.00) (1.22) (10.87) (6.02) Arrangement no. (Inactive for new design for MIL-DTL-38999) Number of Size Service rating location Supersedes M M All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 234
240 s (Insert arrangement 22-2) (11.56) (4.04) (0.00) (2.69) (11.56) (1.35) (0.00) (5.38) (12.24) (1.35) (0.00) (8.08) (11.56) (4.04) (0.00) (10.77) (9.25) (8.08) (2.31) (12.12) (9.25) (5.38) (2.31) (9.42) (9.25) (2.69) (2.31) (6.73) (9.25) (0.00) (2.31) (4.04) (9.25) (2.69) (2.31) (1.35) (9.25) (5.38) (2.31) (1.35) (9.25) (8.08) (2.31) (4.04) (6.93) (9.42) (2.31) (6.73) (6.93) (6.73) (2.31) (9.42) (6.93) (4.04) (2.31) (12.12) FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 235
241 s (Insert arrangement 22-2) (6.93) (1.35) (4.62) (10.77) (6.93) (1.35) (4.62) (8.08) (6.93) (4.04) (4.62) (5.38) (6.93) (6.73) (4.62) (2.69) (7.29) (9.91) (4.62) (0.00) (4.62) (10.77) (4.62) (2.69) (4.62) (8.08) (4.62) (5.38) (4.62) (5.38) (4.62) (8.08) (4.62) (2.69) (4.88) (11.33) (4.62) (0.00) (6.93) (9.42) (4.62) (2.69) (6.93) (6.73) (4.62) (5.38) (6.93) (4.04) (4.62) (8.08) (6.93) (1.35) (4.88) (11.33) (6.93) (1.35) (2.31) (12.12) (6.93) (4.04) (2.31) (9.42) (6.93) (6.73) (2.31) (6.73) (7.29) (9.91) (2.31) (4.04) (9.25) (8.08) (2.31) (1.35) (9.25) (5.38) (2.31) (1.35) (9.25) (2.69) (2.31) (4.04) (9.25) (0.00) (2.31) (6.73) (9.25) (2.69) (2.31) (9.42) (9.25) (5.38) (2.31) (12.12) (9.25) (8.08) (0.00) (10.77) (11.56) (4.04) (0.00) (8.08) (11.56) (1.35) (0.00) (5.38) (12.24) (1.35) (0.00) (2.69) (11.56) (4.04) (0.00) (0.00) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 236
242 s (Insert arrangement 22-21) A (3.25) (9.78) M (7.34) (7.24) B (7.34) (7.24) N (3.25) (9.78) C (9.80) (3.12) P (0.00) (6.22) D (10.16) (1.65) R (4.06) (3.71) E (8.33) (6.07) S (5.44) (.89) F (4.65) (9.19) T (2.39) (4.93) G (0.00) (10.31) U (2.39) (4.93) H (4.65) (9.19) V (5.44) (0.89) J (8.33) (6.07) W (4.06) (3.71) K (10.16) (1.65) X (0.00) (0.00) L (9.80) (3.12) Shell Arrangement Number of Size Service Supersedes size no. rating location II All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 237
243 s (Insert arrangement 22-32) A (2.54) (11.43) T (8.26) (0.64) B (8.26) (8.26) U (7.62) (3.18) C (10.80) (3.81) V (5.08) (6.35) D (11.43) (1.91) W (0.00) (7.62) E (9.53) (6.99) X (5.08) (6.35) F (5.08) (10.16) Y (7.62) (3.18) G (0.00) (11.43) Z (8.26) (0.64) H (5.08) (10.16) a (6.35) (4.45) J (9.53) (6.99) b (3.81) (7.62) K (11.43) (1.91) c (2.54) (3.81) L (10.80) (3.81) d (3.81) (0.00) M (8.26) (8.26) e (1.91) (3.81) N (2.54) (11.43) f (1.91) (3.81) P (0.00) (8.26) g (3.81) (0.00) R (3.81) (7.62) h (2.54) (3.81) S (6.35) (4.45) J (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 238
244 s (Insert arrangement 22-34) A (0.00) (11.43) U (0.00) (7.62) B (4.45) (10.80) V (5.08) (5.72) C (8.26) (8.26) W (7.62) (1.27) D (10.80) (4.45) X (7.62) (2.54) E (11.43) (0.64) Y (3.81) (6.35) F (11.43) (3.18) Z (0.00) (7.62) G (9.53) (6.99) a (3.81) (6.35) H (6.35) (9.53) b (7.62) (2.54) J (2.54) (11.43) c (7.62) (1.27) K (2.54) (11.43) d (5.08) (5.72) L (6.35) (9.53) e (0.00) (3.81) M (9.53) (6.99) f (3.81) (1.27) N (11.43) (3.18) g (3.81) (2.54) P (11.43) (0.64) h (0.00) (3.81) FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 239
245 s (Insert arrangement 22-34) R (10.80) (4.45) J (3.81) (2.54) S (8.26) (8.26) k (3.81) (1.27) T (4.45) (10.80) l (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 240
246 s (Insert arrangement 22-35) (10.87) (6.12) (0.00) (1.19) (11.86) (3.91) (0.00) (3.61) (12.40) (1.55) (0.00) (6.02) (10.54) (0.00) (0.00) (8.43) (12.40) (1.55) (0.00) (10.85) (10.87) (3.61) (2.11) (12.07) (10.87) (6.02) (2.11) (9.65) (8.43) (8.46) (2.11) (7.24) (8.43) (6.05) (2.11) (4.83) (8.43) (3.63) (2.11) (2.41) (8.43) (1.22) (2.11) (0.00) (8.43) (1.19) (2.11) (2.41) (8.43) (3.61) (2.11) (4.83) (8.43) (6.02) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (6.32) (9.65) (2.11) (12.07) 2 FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 241
247 s (Insert arrangement 22-35) (6.32) (7.24) (4.22) (10.87) (6.32) (4.83) (4.22) (8.46) (6.32) (2.41) (4.22) (6.05) (6.32) (0.00) (4.22) (3.63) (6.32) (2.41) (4.22) (1.22) (6.32) (4.83) (4.22) (1.19) (6.32) (7.24) (4.22) (3.61) (6.32) (9.65) (4.22) (6.02) (4.22) (10.87) (4.22) (8.43) (4.22) (8.46) (4.22) (10.85) (4.22) (6.05) (6.32) (9.65) (4.22) (3.63) (6.32) (7.24) (4.22) (1.22) (6.32) (4.83) (4.22) (1.19) (6.32) (2.41) (4.22) (3.61) (6.32) (0.00) (4.22) (6.02) (6.32) (2.41) (4.22) (8.43) (6.32) (4.83) (4.22) (10.85) (6.32) (7.24) (2.11) (12.07) (6.32) (9.65) (2.11) (9.65) (8.43) (8.46) (2.11) (7.24) (8.43) (6.05) (2.11) (4.83) (8.43) (3.63) (2.11) (2.41) (8.43) (1.22) (2.11) (0.00) (8.43) (1.19) (2.11) (2.41) (8.43) (3.61) (2.11) (4.83) (8.43) (6.02) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (10.87) (6.12) (2.11) (12.07) (11.86) (3.91) (0.00) (10.87) (12.40) (1.55) (0.00) (8.46) (10.54) (0.00) FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 242
248 MIL-STD-1560C s (Insert arrangement 22-35) (0.00) (6.05) (12.40) (1.55) (0.00) (3.63) (10.87) (3.61) (0.00) (1.22) (10.87) (6.02) Shell size Arrangement no. (Applicable to MIL-DTL only) Number of Size Service rating location Supersedes D M All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 243
249 s (Insert arrangement 22-36) A (2.54) (11.43) V (3.81) (6.99) B (6.35) (10.16) W (7.62) (3.18) C (8.89) (6.99) X (7.62) (0.64) D (11.43) (2.54) Y (6.99) (4.45) E (11.43) (1.27) Z (3.81) (6.99) F (10.80) (5.08) a (0.00) (7.62) G (7.62) (8.89) b (3.81) (6.99) H (3.81) (10.80) c (6.99) (4.45) J (0.00) (11.43) d (7.62) (0.64) K (3.81) (10.80) e (7.62) (3.18) L (7.62) (8.89) f (3.81) (6.99) M (10.80) (5.08) g (0.00) (3.81) N (11.43) (1.27) h (3.81) (3.18) P (11.43) (2.54) J (3.81) (0.64) R (8.89) (6.99) k (0.00) (3.81) FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 244
250 s (Insert arrangement 22-36) S (6.35) (10.16) l (3.81) (0.64) T (2.54) (11.43) m (3.81) (3.18) U (0.00) (8.26) n (0.00) (0.00) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 245
251 s (Insert arrangement 22-53) A (2.84) (11.56) e (5.72) (6.60) B (5.72) (9.91) f (8.53) (4.95) C (8.53) (8.26) g (8.53) (1.65) D (11.43) (3.30) h (8.53) (1.65) E (11.43) (0.00) k (8.53) (4.95) F (11.43) (3.30) m (5.72) (6.60) G (8.53) (8.26) n (2.84) (8.26) H (5.72) (10.41) p (0.00) (6.60) J (5.72) (10.41) q (2.84) (4.95) K (8.53) (8.26) r (5.72) (3.30) L (11.43) (3.30) s (5.72) (0.00) M (11.43) (0.00) t (5.72) (3.30) N (11.43) (3.30) u (2.84) (4.95) P (8.53) (8.26) v (0.00) (6.60) R (5.72) (9.91) w (2.84) (4.95) S (2.84) (11.56) x (5.72) (3.30) FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 246
252 s (Insert arrangement 22-53) T (0.00) (9.91) y (5.72) (0.00) U (2.84) (8.26) z (5.72) (3.30) V (5.72) (6.60) AA (2.84) (4.95) W (8.53) (4.95) BB (0.00) (3.30) X (8.53) (1.65) CC (2.84) (1.65) Y (8.53) (1.65) DD (2.84) (1.65) Z (8.53) (4.95) EE (.00) (3.30) a (5.72) (6.60) FF (2.84) (1.65) b (2.84) (8.26) GG (2.84) (1.65) c (0.00) (9.91) HH (0.00) (0.00) d (2.84) (8.26) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 247
253 s (Insert arrangement 22-55) A (2.84) (11.56) f (2.84) (8.26) B (5.72) (9.91) g (5.72) (6.60) C (8.53) (8.26) h (8.53) (4.95) D (11.43) (3.30) i (8.53) (1.65) E (11.43) (0.00) J (8.53) (1.65) F (11.43) (3.30) k (8.53) (4.95) G (8.53) (8.26) m (5.72) (6.60) H (5.72) (9.91) n (2.84) (8.26) J (2.84) (11.56) p (0.00) (6.60) K (2.84) (11.56) q (2.84) (4.95) L (5.72) (9.91) r (5.72) (3.30) M (8.53) (8.26) s (5.72) (0.00) N (11.43) (3.30) t (5.72) (3.30) P (11.43) (0.00) u (2.84) (4.95) R (11.43) (3.30) v (0.00) (6.60) S (8.53) (8.26) w (2.84) (4.95) T (5.72) (9.91) x (5.72) (3.30) U (2.84) (11.56) y (5.72) (0.00) FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 248
254 s (Insert arrangement 22-55) V (0.00) (9.91) z (5.72) (3.30) W (2.84) (8.26) AA (2.84) (4.95) X (5.72) (6.60) BB (0.00) (3.30) Y (8.53) (4.95) CC (2.84) (1.65) Z (8.53) (1.65) DD (2.84) (1.65) a (8.53) (1.65) EE (0.00) (3.30) b (8.53) (4.95) FF (2.84) (1.65) c (5.72) (6.60) GG (2.84) (1.65) d (2.84) (8.26) HH (0.00) (0.00) e (0.00) (9.91) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 249
255 s (Insert arrangement 22-97) A (0.00) (8.74) J (8.33) (6.07) B (5.33) (6.86) K (10.16) (1.65) C (9.80) (3.12) L (9.80) (3.12) D (10.16) (1.65) M (5.33) (6.86) E (8.33) (6.07) N (0.00) (3.96) F (4.65) (9.19) P (3.05) (0.76) G (0.00) (10.31) R (0.00) (5.54) H (4.65) (9.19) S (3.05) (0.76) Shell size Arrangement no. Number of Size Service rating location Supersedes I All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 250
256 s (Insert arrangement 22-99) A (0.00) (10.26) G (10.26) (0.00) B (7.62) (6.86) H (7.62) (6.86) C (10.26) (0.00) J (3.05) (3.81) D (6.10) (5.33) K (0.00) (1.52) E (0.00) (7.62) L (3.05) (3.81) F (6.10) (5.33) Shell size Arrangement no. Number of Size Service rating location Supersedes II All MS FIGURE 17. Insert arrangement, electrical connector, shell size 22 (series II of MIL-DTL and series II of MIL-DTL-27599) 251
257 s (Insert arrangement 24-1) (12.17) (7.09) (0.00) (1.19) (13.21) (4.83) (0.00) (3.61) (13.87) (2.41) (0.00) (6.02) (14.10) (0.00) (0.00) (8.43) (13.87) (2.41) (0.00) (10.85) (13.21) (4.83) (0.00) (14.10) (12.17) (7.09) (2.11) (12.07) (10.77) (9.07) (2.11) (9.65) (10.54) (4.83) (2.11) (7.24) (10.54) (2.41) (2.11) (4.83) (10.54) (0.00) (2.11) (2.41) (10.54) (2.41) (2.11) (0.00) (10.54) (4.83) (2.11) (2.41) (10.77) (9.07) (2.11) (4.83) (8.43) (11.28) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599). 252
258 s (Insert arrangement 24-1) (8.43) (6.02) (2.11) (12.07) (8.43) (3.61) (4.06) (13.49) (8.43) (1.19) (4.22) (10.85) (8.43) (1.19) (4.22) (8.43) (8.43) (3.61) (4.22) (6.02) (8.43) (6.02) (4.22) (3.61) (8.43) (8.43) (4.22) (1.19) (8.43) (10.85) (4.22) (1.19) (6.32) (12.60) (4.22) (3.61) (6.32) (9.65) (4.22) (6.02) (6.32) (7.24) (4.22) (8.43) (6.32) (4.83) (4.22) (10.85) (6.32) (2.41) (4.22) (13.26) (6.32) (0.00) (6.32) (12.60) (6.32) (2.41) (6.32) (9.65) (6.32) (4.83) (6.32) (7.24) (6.32) (7.24) (6.32) (4.83) (6.32) (9.65) (6.32) (2.41) (6.32) (12.07) (6.32) (0.00) (4.06) (13.49) (6.32) (2.41) (4.22) (10.85) (6.32) (4.83) (4.22) (8.43) (6.32) (7.24) (4.22) (6.02) (6.32) (9.65) (4.22) (3.61) (6.32) (12.07) (4.22) (1.19) (8.43) (11.28) (4.22) (1.19) (8.43) (8.43) (4.22) (3.61) (8.43) (6.02) (4.22) (6.02) (8.43) (3.61) (4.22) (8.43) (8.43) (1.19) (4.22) (10.85) (8.43) (1.19) (4.22) (13.26) (8.43) (3.61) (2.11) (12.07) (8.43) (6.02) (2.11) (9.65) (8.43) (8.43) (2.11) (7.24) (8.43) (10.85) FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 253
259 s (Insert arrangement 24-1) (2.11) (4.83) (10.77) (9.07) (2.11) (2.41) (10.54) (4.83) (2.11) (0.00) (10.54) (2.41) (2.11) (2.41) (10.54) (0.00) (2.11) (4.83) (10.54) (2.41) (2.11) (7.24) (10.54) (4.83) (2.11) (9.65) (10.77) (9.07) (2.11) (12.07) (12.17) (7.09) (0.00) (13.26) (13.21) (4.83) (0.00) (10.85) (13.87) (2.41) (0.00) (8.43) (14.10) (0.00) (0.00) (6.02) (13.87) (2.41) (0.00) (3.61) (13.21) (4.83) (0.00) (1.19) (12.17) (7.09) (Inactive for new design for MIL-DTL-38999) Shell Arrangement Number of Size Service Supersedes size no. rating location M M All MS FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 254
260 s (Insert arrangement 24-2) (13.97) (.99) (1.35) (12.75) (13.97) (1.73) (1.35) (10.08) (11.66) (6.43) (1.35) (7.42) (13.28) (4.45) (1.35) (4.75) (11.66) (2.34) (1.35) (2.08) (11.66) (0.36) (1.35) (0.58) (11.66) (3.10) (1.35) (3.25) (12.93) (5.46) (1.35) (5.92) (11.66) (7.80) (1.35) (8.59) (8.99) (10.67) (1.35) (11.25) (8.99) (8.00) (1.35) (13.92) (8.99) (5.33) (3.91) (13.34) (8.99) (2.67) (3.91) (10.67) (8.99) (0.00) (3.91) (8.00) FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 255
261 s (Insert arrangement 24-2) (8.99) (2.67) (3.91) (5.33) (8.99) (5.33) (3.91) (2.67) (8.99) (8.00) (3.91) (0.00) (8.99) (10.67) (3.91) (2.67) (6.48) (11.61) (3.91) (5.33) (6.48) (8.94) (3.91) (8.00) (6.48) (6.27) (3.91) (10.67) (6.48) (3.61) (3.91) (13.34) (6.48) (0.94) (6.48) (11.61) (6.48) (1.73) (6.48) (8.94) (6.48) (4.39) (6.48) (6.27) (6.48) (7.06) (6.48) (3.61) (6.48) (9.73) (6.48) (0.94) (6.48) (12.40) (6.48) (1.73) (3.91) (13.34) (6.48) (4.39) (3.91) (10.67) (6.48) (7.06) (3.91) (8.00) (6.48) (9.73) (3.91) (5.33) (6.48) (12.40) (3.91) (2.67) (8.99) (10.67) (3.91) (0.00) (8.99) (8.00) (3.91) (2.67) (8.99) (5.33) (3.91) (5.33) (8.99) (2.67) (3.91) (8.00) (8.99) (0.00) (3.91) (10.67) (8.99) (2.67) (3.91) (13.34) (8.99) (5.33) (1.35) (12.75) (8.99) (8.00) (1.35) (10.08) (8.99) (10.67) (1.35) (7.42) (11.66) (6.43) (1.35) (4.75) (13.28) (4.45) (1.35) (2.08) (11.66) (2.34) FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 256
262 s (Insert arrangement 24-2) (1.35) (0.58) (11.66) (0.36) (1.35) (3.25) (11.66) (3.10) (1.35) (5.92) (12.93) (5.46) (1.35) (8.59) (11.66) (7.80) (1.35) (11.25) (13.97) (0.99) (1.35) (13.92) (13.97) (1.73) (Inactive for new design for MIL-DTL ) Shell Arrangement Number of Size Service Supersedes size no. rating location M All MS FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 257
263 s (Insert arrangement 24-4) A (1.75) (13.49) f (10.46) (0.00) B (5.16) (12.57) g (9.58) (3.35) C (8.23) (10.80) h (7.90) (6.38) D (10.77) (8.28) k (5.38) (8.74) E (12.52) (5.21) m (2.18) (10.08) F (13.49) (1.75) n (2.18) (10.08) G (13.49) (1.75) p (5.38) (8.74) H (12.52) (5.21) q (7.90) (6.38) J (10.77) (8.28) r (9.58) (3.35) K (8.23) (10.80) s (10.46) (0.00) L (5.16) (12.57) t (9.58) (3.35) M (1.75) (13.49) u (7.90) (6.38) N (1.75) (13.49) v (5.38) (8.74) P (5.16) (12.57) w (2.18) (10.08) R (8.23) (10.80) x (1.75) (6.68) S (10.77) (8.28) y (4.37) (3.78) T (12.52) (5.21) z (6.55) (0.00) U (13.49) (1.75) AA (4.37) (3.78) V (13.49) (1.75) BB (1.75) (6.68) FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 258
264 s (Insert arrangement 24-4) W (12.52) (5.21) CC (1.75) (6.68) X (10.77) (8.28) DD (4.37) (3.78) Y (8.23) (10.80) EE (6.55) (0.00) Z (5.16) (12.57) FF (4.37) (3.78) a (1.75) (13.49) GG (1.75) (6.68) b (2.18) (10.08) HH (0.00) (3.35) c (5.38) (8.74) JJ (2.18) (0.00) d (7.90) (6.38) KK (0.00) (3.35) e (9.58) (3.35) LL (2.18) (0.00) Shell size Arrangement no Number of Size Service rating I location AA,DD,EE, FF,JJ,LL,y,z All others Supersedes MS FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 259
265 s (Insert arrangement 24-19) A (0.00) (10.39) L (8.99) (5.21) B (5.99) (10.39) M (5.99) (10.39) C (8.99) (5.21) N (3.00) (5.21) D (11.99) (0.00) P (3.00) (5.21) E (8.99) (5.21) R (5.99) (0.00) F (5.99) (10.39) S (3.00) (5.21) G (0.00) (10.39) T (3.00) (5.21) H (5.99) (10.39) U (5.99) (0.00) J (8.99) (5.21) V (.00) (0.00) K (11.99) (0.00) Shell size Arrangement no. Number of Size Service rating location I All FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 260
266 s (Insert arrangement 24-24) A (0.00) (11.99) N (10.24) (7.57) B (5.84) (10.41) P (5.84) (10.41) C (10.24) (7.57) R (0.00) (5.94) D (11.71) (2.54) S (5.84) (4.37) E (10.49) (3.40) T (4.72) (1.57) F (9.40) (8.53) U (5.36) (6.78) G (5.84) (11.20) V (0.00) (8.20) H (0.00) (12.57) W (5.36) (6.78) J (5.84) (11.20) X (4.72) (1.57) K (9.40) (8.53) Y (5.84) (4.37) L (10.49) (3.40) Z (0.00) (0.71) M (11.71) (2.54) a (0.00) (3.84) Shell size Arrangement no Number of Size Service rating I location A,B,D,E,L,M, P,R,S,T,X,Y All others Supersedes MS FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 261
267 s (Insert arrangement 24-29) A (0.00) (12.22) S (2.31) (8.15) B (6.55) (10.31) T (2.31) (8.15) C (10.03) (7.04) U (5.79) (4.93) D (11.91) (2.77) V (8.10) (0.00) E (11.91) (2.77) W (6.10) (4.60) F (10.03) (7.04) X (2.31) (7.37) G (6.68) (10.31) Y (2.31) (7.37) H (2.31) (11.99) Z (6.10) (4.60) J (2.31) (11.99) a (8.10) (0.00) K (6.68) (10.31) b (5.79) (4.93) L (10.03) (7.04) c (0.00) (4.09) M (11.91) (2.77) d (3.40) (0.00) N (11.91) (2.77) e (0.00) (3.30) P (10.03) (7.04) f (3.40) (0.00) R (6.55) (10.31) Shell Arrangement Number of Size Service Supersedes size no. rating location I All MS FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 262
268 s (Insert arrangement 24-35) (12.17) (7.09) (0.00) (1.19) (13.21) (4.83) (0.00) (3.61) (13.87) (2.41) (0.00) (6.02) (14.10) (0.00) (0.00) (8.43) (13.87) (2.41) (0.00) (10.85) (13.21) (4.83) (0.00) (14.10) (12.17) (7.09) (2.11) (12.07) (10.77) (9.07) (2.11) (9.65) (10.54) (4.83) (2.11) (7.24) (10.54) (2.41) (2.11) (4.83) (10.54) (0.00) (2.11) (2.41) (10.54) (2.41) (2.11) (.00) (10.54) (4.83) (2.11) (2.41) (10.77) (9.07) (2.11) (4.83) (8.43) (11.28) (2.11) (7.24) (8.43) (8.43) (2.11) (9.65) (8.43) (6.02) (2.11) (12.07) FIGURE 18. Insert arrangement, electrical connector, shell size 24 (series II of MIL-DTL and series II of MIL-DTL-27599) 263
DEFENSE LOGISTICS AGENCY LAND AND MARITIME P.O. BOX 3990 COLUMBUS, OH
DEFENSE LOGISTICS AGENCY LAND AND MARITIME P.O. BOX 3990 COLUMBUS, OH 43218-3990 July 26, 2018 MEMORANDUM FOR MILITARY/INDUSTRY DISTRIBUTION SUBJECT: Initial draft of MIL-STD-1560 w/change 2 (see table
More informationDETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, STRAIGHT, MINIATURE, CLASSES E, F, G AND R
INCH-POUND MS24266P 7 August 2015 SUPERSEDING MS24266N 20 August 2009 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, STRAIGHT, MINIATURE, CLASSES E, F, G AND R Inactive for new design after 14
More informationDETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, STRAIGHT, MINIATURE, CLASSES E, F, G AND R
INCH-POUND MS24266R 1 December 2016 SUPERSEDING MS24266P 7 August 2015 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, STRAIGHT, MINIATURE, CLASSES E, F, G AND R Inactive for new design after
More informationDETAIL SPECIFICATION SHEET DISK, VALVE. Inactive for new design after 15 October 1998.
INCH-POUND MS29521H 23 September 2015 SUPERSEDING MS29521G 7 April 2009 DETAIL SPECIFICATION SHEET DISK, VALVE Inactive for new design after 15 October 1998. This specification is approved for use by all
More informationDETAIL SPECIFICATION SHEET
METRIC MIL-DTL-38999/31E 12 March 2014 SUPERSEDING MIL-DTL-38999/31D 19 April 2002 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, THREADED, PLUG, LANYARD RELEASE, FAIL-SAFE, REMOVABLE CRIMP
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-24308/24H 8 June 2018 SUPERSEDING MIL-DTL-24308/24H w/amendment 4 8 April 2015 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, NONENVIRONMENTAL, MINIATURE, POLARIZED SHELL,
More informationDETAIL SPECIFICATION SHEET SLEEVE, SWAGING-WIRE ROPE
INCH-POUND 3 December 2012 SUPERSEDING 30 September 2011 DETAIL SPECIFICATION SHEET SLEEVE, SWAGING-WIRE ROPE This specification is approved for use by all Departments and Agencies of the Department of
More informationDETAIL SPECIFICATION SHEET SLEEVE, SWAGING-WIRE ROPE
INCH-POUND 30 September 2011 SUPERSEDING MS51844D 19 April 2007 DETAIL SPECIFICATION SHEET SLEEVE, SWAGING-WIRE ROPE This specification is approved for use by all Departments and Agencies of the Department
More informationDETAIL SPECIFICATION SHEET NUT, TUBE COUPLING, SHORT
INCH-POUND 19 August 2014 SUPERSEDING w/amendment 1 23 January 2013 DETAIL SPECIFICATION SHEET NUT, TUBE COUPLING, SHORT This specification is approved for use by all Departments and Agencies of the Department
More informationMILITARY SPECIFICATION LUBRICATING OIL, VACUUM PUMP, MECHANICAL
INCH-POUND MIL-DTL-83767C 24 September 2007 SUPERSEDING MIL-L-83767B 8 February 1980 MILITARY SPECIFICATION LUBRICATING OIL, VACUUM PUMP, MECHANICAL Reactivated after 24 September 2007 and may be used
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-24236/24E 5 April 2006 SUPERSEDING MIL-PRF-24236/24D 22 January 2001 PERFORMANCE SPECIFICATION SHEET SWITCHES, THERMOSTATIC, (BIMETALLIC), SUBMINIATURE, TYPE I, HERMETICALLY SEALED,
More informationDETAIL SPECIFICATION SHEET CAP INSERT, ASSEMBLY, PRESSURE SEAL, FLARED TUBE FITTING
INCH-POUND Rev 13 7 August 2014 SUPERSEDING w/amendment 1 20 November 2013 DETAIL SPECIFICATION SHEET CAP INSERT, ASSEMBLY, PRESSURE SEAL, FLARED TUBE FITTING This specification is approved for use by
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, SPDT, UNSEALED
INCH-POUND 14 June 2010 SUPERSEDING 22 May 2006 PERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, SPDT, UNSEALED This specification is approved for use by all Departments and Agencies of the Department
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, 10 AMPERES AND LOW LEVEL, UNSEALED
INCH-POUND 2 January 201 SUPERSEDING 1 May 200 PERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, AMPERES AND LOW LEVEL, UNSEALED This specification is approved for use by all Departments and Agencies
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, PLUNGER, 10 AMPERES 2PDT AND 7 AMPERES 4PDT, RESILIENT SEAL
INCH-POUND MIL-PRF-8805/100G 6 December 2012 SUPERSEDING MIL-PRF-8805/100F 4 October 2004 PERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, PLUNGER, 10 AMPERES 2PDT AND 7 AMPERES 4PDT, RESILIENT SEAL
More informationINCH-POUND MIL-DTL-24211D 25 February 2016 SUPERSEDING MIL-DTL-24211C 9 February 2011 DETAIL SPECIFICATION
DETAIL SPECIFICATION INCH-POUND MIL-DTL-24211D 25 February 2016 SUPERSEDING MIL-DTL-24211C 9 February 2011 GASKETS, WAVEGUIDE FLANGE GENERAL SPECIFICATION FOR 1. SCOPE This specification is approved for
More informationDETAIL SPECIFICATION SHEET SWITCHES, TOGGLE, MINIATURE, LEVER SEAL, PANEL SEAL, FOUR POLE LOGIC LOAD TO 5 AMPERES
INCH-POUND MIL-DTL-83731/1B July 010 SUPERSEDING MIL-S-83731/1A 0 March 1987 DETAIL SPECIFICATI SHEET SWITCHES, TOGGLE, MINIATURE, LEVER SEAL, PANEL SEAL, FOUR POLE LOGIC LOAD TO 5 AMPERES Inactive for
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-55302/52D 12 September 2012 SUPERSEDING MIL-DTL-55302/52D 17 December 2003 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: RECEPTACLE, STRAIGHT-THRU,
More informationMILITARY SPECIFICATION SHEET
INCH-POUND MS21363B 2 July 2007 SUPERSEDING MS21363A(USAF) 2 July 1985 MILITARY SPECIFICATION SHEET COILS, RADIO FREQUENCY, MOLDED, FIXED, MICROMINIATURE, MAGNETICALLY SHIELDED, (FERRITE CORE-FERRITE SLEEVE),
More informationDETAIL SPECIFICATION SHEET TRANSMITTER, LIQUID QUANTITY, FLOAT TYPE, ENGINE FUEL. Inactive for new design after 28 September 1993.
INCH-POUND MS500040K 17 November 2011 SUPERSEDING MS500040J 1 March 1991 DETAIL SPECIFICATION SHEET TRANSMITTER, LIQUID QUANTITY, FLOAT TYPE, ENGINE FUEL Inactive for new design after 28 September 1993.
More informationDETAIL SPECIFICATION SHEET
METRIC MIL-DTL-38999/36 30 November 2006 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, THREADED, PLUG, LANYARD RELEASE, FAIL-SAFE, REMOVABLE CRIMP CONTACTS, PINS, SHELL SIZE 25, SERIES III,
More informationDEPARTMENT OF DEFENSE STANDARD PRACTICE IDENTIFICATION CODING AND APPLICATION OF HOOKUP AND LEAD WIRE
NOTICE OF CHANGE INCH-POUND MIL-STD-681D NOTICE 1 19 June 2000 DEPARTMENT OF DEFENSE STANDARD PRACTICE IDENTIFICATION CODING AND APPLICATION OF HOOKUP AND LEAD WIRE TO ALL HOLDERS OF MIL-STD-681D: 1. THE
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-83536/15A 12 July 2004 SUPERSEDING MIL-PRF-83536/15 27 March 1992 PERFORMANCE SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, ESTABLISHED RELIABILITY, 4PDT, LOW LEVEL TO 10 AMPERES, PERMANENT
More informationCOMMERCIAL ITEM DESCRIPTION CLAMPS, HOSE
INCH-POUND 7 JUNE 2006 SUPERSEDING A-A-52506B 16 AUGUST 1996 COMMERCIAL ITEM DESCRIPTION CLAMPS, HOSE The General Services Administration has authorized the use of this Commercial Item Description (CID)
More informationDETAIL SPECIFICATION SHEET NUT, TUBE COUPLING, SHORT
INCH-POUND 16 February 2010 SUPERSEDING AN818 Rev 19 15 June 1994 DETAIL SPECIFICATION SHEET NUT, TUBE COUPLING, SHORT This specification is approved for use by all Departments and Agencies of the Department
More informationDETAIL SPECIFICATION SHEET SWITCHES, ROTARY, SNAP ACTION CLASS 1SR BASE MOUNTED, SIDE CONNECTED
INCH-POUND 6 February 2006 SUPERSEDING MIL-S-15291/3A(SH) 22 July 1991 DETAIL SPECIFICATION SHEET SWITCHES, ROTARY, SNAP ACTION CLASS 1SR BASE MOUNTED, SIDE CONNECTED This specification is approved for
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-24308/36 1 April 2015 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, COMBINATION INSERT ARRANGEMENT, RECEPTACLE, SOCKET CONTACTS, SHELL SIZE 4, SIZE 20 SIGNAL
More informationPERFORMANCE SPECIFICATION SHEET
INCHPOUND MILPRF39006/31D 21 March 2018 SUPERSEDING MILPRF39006/31C 21 April 2011 PERFORMANCE SPECIFICATION SHEET CAPACITOR, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM (POLARIZED, SINTERED SLUG),
More informationFEDERAL SPECIFICATION ETHER, PETROLEUM; TECHNICAL GRADE. 1.1 Scope. This specification covers technical grade petroleum ether to be used as a solvent.
METRIC 4 May 2015 SUPERSEDING O-E-751C 10 January 2003 FEDERAL SPECIFICATION ETHER, PETROLEUM; TECHNICAL GRADE The General Services Administration has authorized the use of this federal specification by
More informationMILITARY SPECIFICATION MICROCIRCUITS, LINEAR, CMOS, ANALOG SWITCH WITH DRIVER, MONOLITHIC SILICON
INCH-POUND 4 February 2004 SUPERSEDING MIL-M-38510/116 16 April 1980 MILITARY SPECIFICATION MICROCIRCUITS, LINEAR, CMOS, ANALOG SWITCH WITH DRIVER, MONOLITHIC SILICON This specification is approved for
More informationPERFORMANCE SPECIFICATION COOLERS, LUBRICATING OIL, AIRCRAFT, GENERAL SPECIFICATION FOR
INCH-POUND 06 May 2013 SUPERSEDING MIL-PRF-25478C 29 December 1997 PERFORMANCE SPECIFICATION COOLERS, LUBRICATING OIL, AIRCRAFT, GENERAL SPECIFICATION FOR This specification is approved for use by all
More informationCOMMERCIAL ITEM DESCRIPTION PINTLE ASSEMBLY, TOWING, MANUAL RELEASE, , AND LBS CAPACITY
[INCH-POUND] July 30, 1996 SUPERSEDING (see 7.5) COMMERCIAL ITEM DESCRIPTION PINTLE ASSEMBLY, TOWING, MANUAL RELEASE, 18 000, 40 000 AND 100 000 LBS CAPACITY The General Services Administration has authorized
More informationPERFORMANCE SPECIFICATION SHEET RUBBER, SYNTHETIC, TUBING
INCH-POUND 15 June 2009 SUPERSEDING MIL-R-6855/4 16 February 1987 PERFORMANCE SPECIFICATION SHEET RUBBER, SYNTHETIC, TUBING This specification is approved for use by all Departments and Agencies of the
More informationCOMMERCIAL ITEM DESCRIPTION RELAYS, ELECTROMAGNETIC, GENERAL PURPOSE 10 AMPERES, 1-3PDT, AC AND DC COILS, FLANGE MOUNT
INCH-POUND w/amendment 1 1 November 2005 SUPERSEDING A-A-55143/2A 15 October 2000 COMMERCIAL ITEM DESCRIPTION RELAYS, ELECTROMAGNETIC, GENERAL PURPOSE 10 AMPERES, 1-, AC AND DC COILS, FLANGE MOUNT The
More informationCOMMERCIAL ITEM DESCRIPTION RELAYS, ELECTROMAGNETIC, GENERAL PURPOSE 10 AMPERES, 1-3PDT, AC AND DC COILS, SOCKET MOUNT
INCH-POUND A-A-55143/1C 28 February 200 SUPERSEDING A-A-55143/1B 15 October 2000 COMMERCIAL ITEM DESCRIPTION RELAYS, ELECTROMAGNETIC, GENERAL PURPOSE 10 AMPERES, 1-, AC AND DC COILS, SOCKET MOUNT The General
More informationFEDERAL SPECIFICATION METHANOL (METHYL ALCOHOL) 1.1 Scope. This specification covers three grades and four unit quantities of methanol.
NOT MEASUREMENT SENSITIVE 19 January 2016 SUPERSEDING O-M-232L 4 January 2006 FEDERAL SPECIFICATION METHANOL (METHYL ALCOHOL) The General Services Administration has authorized the use of this federal
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND PERFORMANCE SPECIFICATION SHEET MIL-PRF-2886/E 28 Septmebr 206 SUPERSEDING MIL-PRF-2886/D w/amendment 0 May 2005 FILTERS AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE SUPPRESSION,
More informationPERFORMANCE SPECIFICATION SHEET BATTERY, RECHARGEABLE, NICKEL CADMIUM, VENTED, 1.2-VOLT, 13 AMPERE- HOUR, BB-475/A CELL
INCH-POUND 25 FEB 2011 PERFORMANCE SPECIFICATION SHEET BATTERY, RECHARGEABLE, NICKEL CADMIUM, VENTED, 1.2-VOLT, 13 AMPERE- HOUR, BB-475/A CELL This specification is approved for use within Army CECOM Life
More informationPERFORMANCE SPECIFICATION
INCH-POUND 19 March 2008 PERFORMANCE SPECIFICATION LIGHT EMITTING DIODE (LED) COMPOSITE STOP, REAR TURN SIGNAL AND TAIL LAMPS WITH INFRA-RED SECURE BLACKOUT TAIL AND BLACKOUT STOP LAMPS This specification
More informationPERFORMANCE SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIO FREQUENCY. (BETWEEN SERIES BNC TO SERIES TNC), CLASS 2, STRAIGHT PLUG
INCH-POUND MIL-PRF-55339/38A 10 January 2005 SUPERSEDING MIL-PRF-55339/38 11 January 1977 PERFORMANCE SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIO FREQUENCY. (BETWEEN SERIES BNC TO SERIES TNC),
More informationMILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY TTL, NAND GATES, MONOLITHIC SILICON
INCH-POUND MIL-M-38510/370A 15 July 2004 SUPERSEDING MIL-M-38510/370(USAF) 18 March 1983 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY TTL, NAND GATES, MONOLITHIC
More informationDETAIL SPECIFICATION GASKETS, WAVEGUIDE FLANGE GENERAL SPECIFICATION FOR
INCH-POUND 25 November 1998 SUPERSEDING MIL-G-24211 28 MARCH 1966 DETAIL SPECIFICATION GASKETS, WAVEGUIDE FLANGE GENERAL SPECIFICATION FOR This specification is approved for use by all Departments and
More informationDETAIL SPECIFICATION RUBBER, FLUOROSILICONE ELASTOMER, OIL AND FUEL RESISTANT, SHEETS, STRIPS, MOLDED PARTS, AND EXTRUDED SHAPES
INCH-POUND 11 August 2006 SUPERSEDING MIL-R-25988B 12 July 1983 DETAIL SPECIFICATION RUBBER, FLUOROSILICONE ELASTOMER, OIL AND FUEL RESISTANT, SHEETS, STRIPS, MOLDED PARTS, AND EXTRUDED SHAPES Reactivated
More informationPERFORMANCE SPECIFICATION COOLERS, LUBRICATING OIL, AIRCRAFT, GENERAL SPECIFICATION FOR
I INCH-POUND 29 December 1997 SUPERSEDING MIL-C-25478B(USAF) 28 March 1995 PERFORMANCE SPECIFICATION COOLERS, LUBRICATING OIL, AIRCRAFT, GENERAL SPECIFICATION FOR This specification is approved for use
More informationCOMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 02
METRIC A-A-59584C 15 September 2008 SUPERSEDING A-A-59584B 23 September 2003 COMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 02 The General Services
More information[INCH-POUND] A-A December 1999 SUPERSEDING MIL-C-4109F 31 October 1986
[INCH-POUND] 30 December 1999 SUPERSEDING MIL-C-4109F 31 October 1986 COMMERCIAL ITEM DESCRIPTION COUPLING HALVES, QUICK-DISCONNECT The General Services Administration has authorized the use of this commercial
More informationCOMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 03
METRIC A-A-59585C 15 September 2008 SUPERSEDING A-A-59585B 23 September 2003 COMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 03 The General Services
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, MOMENTARY, 4 CIRCUIT OR DPDT (10 AMPERES), UNSEALED
INCH-POUND MIL-PRF-8805/77H 19 September, 2000 SUPERSEDING MIL-PRF-8805/77G 3 September 1999 PERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, MOMENTARY, 4 CIRCUIT OR DPDT (10 AMPERES), UNSEALED This
More informationPERFORMANCE SPECIFICATION ACTUATOR, LINEAR, ELECTROMECHANICAL
INCH-POUND PERFORMANCE SPECIFICATION 17 September 2015 SUPERSEDING MIL-A-85046(AS) 7 September 1976 ACTUATOR, LINEAR, ELECTROMECHANICAL This specification is approved for use by the Naval Air Systems Command
More informationPERFORMANCE SPECIFICATION LUBRICATING OIL, JET ENGINE
INCH-POUND 12 December 2014 SUPERSEDING MIL-PRF-6081D w/amendment 1 30 January 2009 PERFORMANCE SPECIFICATION LUBRICATING OIL, JET ENGINE This specification is approved for use by all Departments and Agencies
More informationMIL-STD S 26 JULY 1985
k -. Downloaded from http://www.everyspec.com -- MIL-STD-3-S 6 JULY 985 SUPERSEDING MIL-STD-3(ln 3 MAY 967 part) MILITARY STANDARD FASTENER TEST METHODS METHOD 5, DRIVING RECESS TORQUE QUALITY CONFORMANCE
More informationFeatures and Application
MIL-DTL-38999 Features and Application Series II Features and Application MIL-DTL-38999 Series II connectors feature a bayonet coupling mechanism with lower profile design and rear-removable crimp contact
More informationAmphenol. Amphenol /Matrix MIL-C-83723, Series III Connectors. Bayonet, Threaded or Quick-Disconnect Coupling Connectors for Demanding Environments
Amphenol /Matrix MIL-C-, Series III Connectors -0- Bayonet, Threaded or Quick-Disconnect Coupling Connectors for Demanding Environments Amphenol This catalog covers the Amphenol /Matrix MIL-C-, Series
More informationDETAIL SPECIFICATION SHEET COUPLING HALF, HOSE ATTACHMENT, HYDRAULIC, SELF-SEALING, GROUND SUPPORT, QUICK DISCONNECT, TYPE I AND TYPE II
INCH-POUND 08 December 2009 DETAIL SPECIFICATION SHEET COUPLING HALF, HOSE ATTACHMENT, HYDRAULIC, SELF-SEALING, GROUND SUPPORT, QUICK DISCONNECT, TYPE I AND TYPE II This specification is approved for use
More informationMIL-DTL Series III Connectors
RELIABLE Self-locking threaded coupling 100% scoop proof Contact retention system provides excellent contact retention under severe vibration EMI PROTECTED Grounding fingers for excellent EMI protection
More informationQQ-W-343F 19 November 1990 (TO SUPERSEDE) QQ-W-343-E November 13, 1981 FEDERAL SPECIFICATION WIRE, ELECTRICAL, COPPER (UNINSULATED)
19 November 1990 (TO SUPERSEDE) QQ-W-343-E November 13, 1981 FEDERAL SPECIFICATION WIRE, ELECTRICAL, COPPER (UNINSULATED) 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers solid, bunch-stranded,
More informationFeatures and Application
ML-DTL- Features and Application MS2426*/AE66* Features and Application ML-DTL- family offers connectors with bayonet coupling as well as threaded coupling. These connectors are intermateable with correspondingly
More informationGenuine Aircraft Hardware Co. MIL H 6000 B It is for push on and clamp applications.
Genuine Aircraft Hardware Co. MIL H 6000 B This oil-resistant tube is reinforced with a high strength, mildew-resistant yarn designed to withstand oil, alcohol, coolant, fuel, water and temperatures from
More informationPERFORMANCE SPECIFICATION GREASE, AIRCRAFT, GENERAL PURPOSE, WIDE TEMPERATURE RANGE, NATO CODE G-395
METRIC 24 January 2005 SUPERSEDING MIL-PRF-81322F 21 July 1998 PERFORMANCE SPECIFICATION GREASE, AIRCRAFT, GENERAL PURPOSE, WIDE TEMPERATURE RANGE, NATO CODE G-395 This specification is approved for use
More informationMILITARY SPECIFICATION SHEET SCREW, CAP, HEXAGON HEAD (FINISHED HEXAGON BOLT), STEEL, CORROSION RESISTING, PASSIVATED, UNC-2A
INCH-POUND MS35307E 25 April 1997 Superseding MS35307D 1 May 1969 MILITARY SPECIFICATION SHEET SCREW, CAP, HEXAGON HEAD (FINISHED HEXAGON BOLT), STEEL, CORROSION RESISTING, PASSIVATED, UNC-2A This specification
More informationTABLE OF CONTENTS. Amphenol Aerospace is a Certified ISO 9001 Manufacturer.
This catalog covers the Amphenol /Matrix MIL-C- 83723, Series III Connectors. These connectors incorporate crimp rear release contacts. There is great diversity within this cylindrical family, with the
More informationMIL-DTL Series IV Connectors
DEPENDABLE Secure breech lock coupling 100% scoop-proof Pin-to-pin mating protection helps prevent failures RUGGED Mated connectors help withstand high-impact shock Rear accessory threads help provide
More informationFEDERAL SPECIFICATION TRUCKS, HAND, TWO WHEELED
INCH-POUND KKK T 683F 15 December 2010 SUPERSEDING KKK T 683E w/amendment 1 11 July 2005 FEDERAL SPECIFICATION TRUCKS, HAND, TWO WHEELED The General Services Administration has authorized the use of this
More informationDEPARTMENT OF DEFENSE STANDARD PRACTICE
DEPARTMENT OF DEFENSE STANDARD PRACTICE ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS) INCH-POUND 3 September 2009 SUPERSEDING DOD-STD-2003-5(SH) 24 June 1987
More informationDETAIL SPECIFICATION SHEET
INCH-POUND 30 June 2014 SUPERSEDING MIL-DTL-16377/53C 27 September 2005 DETAIL SPECIFICATION SHEET FIXTURES, LIGHTING; INCANDESCENT AND LIGHT EMITTING DIODE (LED), DETAIL LIGHTING, LANTERN, HAND, PORTABLE
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-17361/4B(SH) 19 September 2006 SUPERSEDING MIL-C-17361/4A(SH) 13 March 1995 DETAIL SPECIFICATION SHEET CIRCUIT BREAKERS, AIR, ELECTRIC, INSULATED HOUSING (SHIPBOARD USE) TYPES AQB-A101,
More informationCOMMERCIAL ITEM DESCRIPTION HOSE AND HOSE ASSEMBLIES, NONMETALLIC SPRAY
[INCH-POUND] A-A-59613 August 16, 2001 SUPERSEDING ZZ-H-521F May 28, 1993 COMMERCIAL ITEM DESCRIPTION HOSE AND HOSE ASSEMBLIES, NONMETALLIC SPRAY The General Services Administration has authorized the
More informationDETAIL SPECIFICATION HOSE, SYNTHETIC RUBBER - HYDRAULIC FLUID, FUEL, AND OIL RESISTANT
INCH-POUND 16 April 2007 SUPERSEDING MIL-DTL-8794E 22 September 2000 DETAIL SPECIFICATION HOSE, SYNTHETIC RUBBER - HYDRAULIC FLUID, FUEL, AND OIL RESISTANT This specification is approved for use by all
More informationPERFORMANCE SPECIFICATION CALIBRATING FLUIDS, AIRCRAFT FUEL SYSTEM COMPONENTS
METRIC 20 January 2012 SUPERSEDING MIL-PRF-7024E 1 October 1997 PERFORMANCE SPECIFICATION CALIBRATING FLUIDS, AIRCRAFT FUEL SYSTEM COMPONENTS Comments, suggestions, or questions on this document should
More informationMILITARY SPECIFICATION MOUNT, TELESCOPE AND QUADRANT: M172
MILITARY SPECIFICATION MOUNT, TELESCOPE AND QUADRANT: M172 30 MARCH 1990 SUPERSEDING MIL-M-48559(MU) 12 September 1975 This specification is approved for use by the U.S. Army Armament, Munitions and-chemical
More informationPERFORMANCE SPECIFICATION SHEET BATTERY, STORAGE, AIRCRAFT, MAINTENANCE-FREE, 24-VOLT, 1.5-AMPERE-HOUR
METRIC MIL-PRF-8565/6A (AS) 25 June 2001 SUPERSEDING DOD-B-8565/6(AS) 26 June 1987 PERFORMANCE SPECIFICATION SHEET BATTERY, STORAGE, AIRCRAFT, MAINTENANCE-FREE, 24-VOLT, 1.5-AMPERE-HOUR This specification
More informationMIL-DTL Series 1 Solder Type PT
MIL-DTL-26482 Series 1 Solder Type PT The Amphenol Miniature Cylindrical Connector Series offers high density contact arrangements in a miniature, circular metal shell. This connector is environmentally
More informationMIL-DTL SERIES III CONNECTORS RUGGED, HARSH ENVIRONMENT SUBMINIATURE CONNECTORS
QUICK REFERENCE GUIDE Wide Range Mil spec, commercial, and composite Full line of finishes, including black zinc nickel and PTFE nickel High Performance Environmentally sealed DEUTSCH MIL-DTL-38999 SERIES
More informationPERFORMANCE SPECIFICATION GREASE, AUTOMOTIVE AND ARTILLERY
NOT MEASUREMENT SENSITIVE w/ 26 September 2012 SUPERSEDING 30 September 2008 PERFORMANCE SPECIFICATION GREASE, AUTOMOTIVE AND ARTILLERY This specification is approved for use by all Departments and Agencies
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-22710/14F 20 April 2001 SUPERSEDING MIL-S-22710/14E 18 October 1982 PERFORMANCE SPECIFICATION SHEET SWITCHES, CODE INDICATING WHEEL (PRINTED CIRCUIT), (THUMBWHEEEL SWITCH ASSEMBLY, INTEGRAL
More informationSeries 80 Mighty Mouse Technical Reference Complete Product Specification
Summary Performance Specifications Current Rating (Maximum): Size #23 Contact: 5 A., Size #20 contact: 7.5 A., Size #16 contact: 13 A., Size #12 contact: 23 A. Test Voltage (Dielectric Withstanding Voltage)
More informationMIL-DTL-83723, Series III, Pyle
TALE OF CONTENTS Table of Contents....................... 37 Design Features, Customer Options, Manufacturer s Specifications. 38, 39 Quick Reference of Choices - Threaded Styles......... 40-42 Quick Reference
More informationPERFORMANCE SPECIFICATION
METRIC 05 November 2015 SUPERSEDING MIL-PRF-7870D 30 April 2010 PERFORMANCE SPECIFICATION LUBRICATING OIL: GENERAL PURPOSE, LOW-TEMPERATURE (NATO O-142) This specification is approved for use by all Departments
More informationDETAIL SPECIFICATION DETECTOR PAD, FREE WATER. This specification is approved for use by all Departments and Agencies of the Department of Defense.
METRIC DETAIL SPECIFICATION DETECTOR PAD, FREE WATER 31 March 2006 SUPERSEDING MIL-D-81248B 30 June 1980 This specification is approved for use by all Departments and Agencies of the Department of Defense.
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-16377/53C 27 September 2005 SUPERSEDING MIL-DTL-16377/53B(SH) 25 November 1996 DETAIL SPECIFICATION SHEET FIXTURES, INCANDESCENT AND LIGHT EMITTING DIODE (LED), DETAIL LIGHTING, LANTERN,
More informationThis specification is approved for use by all Departments and Agencies of the Department of Defense.
INCH-POUND MIL-PRF-39014/5F 16 September 1997 SUPERSEDING MIL-C-39014/5E 16 August 1978 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), ESTABLISHED RELIABILITY,
More informationINCH-POUND. MIL-PRF-46103E 6 January 1998 SUPERSEDING MIL-A-46103D 23 June l989 PERFORMANCE SPECIFICATION ARMOR: LIGHTWEIGHT, COMPOSITE
INCH-POUND MIL-PRF-46103E 6 January 1998 SUPERSEDING MIL-A-46103D 23 June l989 PERFORMANCE SPECIFICATION ARMOR: LIGHTWEIGHT, COMPOSITE This specification is approved for use by all Departments and Agencies
More informationMILITARY SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), STYLE CK05
INCH-POUND MIL-C-11015/18E 14 May 2001 SUPERSEDING MIL-C-11015/18D 28 September 1970 MILITARY SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), STYLE CK05 The requirements for
More information38999 Series III Composite Connectors
8D Series Composite 38999 Series III Composite Connectors The RoHS connector with the best performance in weight saving and corrosion resistance for MilAero applications. MIL-DTL-38999 Standard Versatility
More informationDownloaded from
December 20, 1989 TO SUPERSEDE W-F-408D 30 March 1984 FEDERAL SPECIFICATION FITTINGS FOR CONDUIT, METAL, RIGID (THICK-WALL AND THIN-WALL (EMT) TYPE) This specification is approved by the Commissioner.
More information45 YEARS OF EXPERIENCE
ENGINE CONNECTORS 45 YEARS OF EXPERIENCE High Performance Connectors for Critical Environment Temperature Up to 350ºC / 662ºF Vibrations Fire Corrosion 45 YEARS OF EXPERIENCE OLD PRODUCTS DBA 3x NEW GENERATION
More informationREVISIONS SYMBOL DESCRIPTION DATE APPROVAL
REVISIONS SYMBOL DESCRIPTION DATE APPROVAL L Revised per RN A-203. 2/23/16 JS K Revised per RN A-191 12/29/14 JS J Revised per RN A-183 4/25/13 JS I Revised per RN A-170. 7/15/11 JS H Revised per RN A-151.
More informationMILITARY SPECIFICATION CORROSION PREVENTIVE COMPOUNDS, WATER DISPLACING, ULTRA-THIN FILM PAGE 1
NOT MEASUREMENT SENSITIVE 26 November 1997 SUPERSEDING AMENDMENT 2 31 July 1996 MILITARY SPECIFICATION CORROSION PREVENTIVE COMPOUNDS, WATER DISPLACING, ULTRA-THIN FILM This amendment forms a part of,
More informationFeatures and Application
ML-DTL-83723 Series Features and Application Bayonet and Threaded Coupling Features and Application ML-DTL-83723 Series family offers connectors with bayonet and threaded coupling including lanyard-release
More informationMIL-DTL-83723, Series III, Pyle
MIL-DTL-83723, Series III, TALE OF CONTENTS FOR SECTION Design Features, Customer Options, Specifications.... 8, 9 Quick Reference of Choices - Threaded Styles.... 20-22 Quick Reference of Choices - ayonet
More informationPROCUREMENT SPECIFICATION FOR CNP19 CHERRY RIVETLESS NUT PLATE
PROCUREMENT SPECIFICATION NUMBER PRINTED COPIES OF THIS DOCUMENT ARE CONSIDERED REFERENCE UNLESS OTHERWISE STAMPED IN RED INK. PROCUREMENT SPECIFICATION FOR CNP19 CHERRY RIVETLESS NUT PLATE Authorizing
More informationCOMMERCIAL ITEM DESCRIPTION HOSE ASSEMBLY, NONMETALLIC, FIRE FIGHTING, WITH COUPLINGS
[INCH-POUND] A-A-59226 May 18, 1998 SUPERSEDING ZZ-H-451G January 13, 1984 COMMERCIAL ITEM DESCRIPTION HOSE ASSEMBLY, NONMETALLIC, FIRE FIGHTING, WITH COUPLINGS The General Services Administration has
More informationSURFACE VEHICLE RECOMMENDED PRACTICE
SURFACE VEHICLE RECOMMENDED PRACTICE J1095 Issued 1982-06 Revised 2003-03 REV. MAR2003 Superseding J1095 MAR1995 Spoke Wheels and Hub Fatigue Test Procedures 1. Scope This SAE Recommended Practice provides
More informationTHREADED & BAYONET CONNECTORS FOR DEMANDING ENVIRONMENTS
MILITARY AND COMMERCIAL AVIATION MIL - DTL - 83723 SERIES III THREADED & BAYONET CONNECTORS FOR DEMANDING ENVIRONMENTS CONNECTORS FOR DEMANDING ENVIRONMENTS THREADED AND BAYONET MILITARY AND COMMERCIAL
More informationOASIS. Standby Instrument System. Installation Manual. Aerosonic Corporation September 18, N. Hercules Ave. Clearwater, FL USA
OASIS Standby Instrument System Installation Manual Aerosonic Corporation September 18, 2012 1212 N. Hercules Ave. Clearwater, FL 33765 USA INSTALLATION MANUAL OASIS Original Aerosonic Standby Instrument
More informationPERFORMANCE SPECIFICATION LIGHT EMITTING DIODE (LED) MILITARY DRIVING HEADLAMP
INCH-POUND 12 March 2009 PERFORMANCE SPECIFICATION LIGHT EMITTING DIODE (LED) MILITARY DRIVING HEADLAMP This specification is approved for use by all Departments and Agencies of the Department of Defense.
More informationPERFORMANCE SPECIFICATION GREASE, AIRCRAFT AND INSTRUMENT, FUEL AND OXIDIZER RESISTANT
METRIC 15 August 211 SUPERSEDING MILPRF27617F 17 February 1998 PERFORMANCE SPECIFICATION GREASE, AIRCRAFT AND INSTRUMENT, FUEL AND OXIDIZER RESISTANT Comments, suggestions, or questions on this document
More informationMIL-DTL-38999Series III Composite Series
MIL-DTL-38999Series III Composite Series 25 Connector part numbers Basic Series 8D 0-11 J 35 P N ** Shell style: 0: Square flange receptacle 1: In line receptacle 5: Plug with RFI shielding. Type: -: Connectors
More informationCOMMERCIAL ITEM DESCRIPTION HOSE ASSEMBLY, NONMETALLIC, FIRE FIGHTING, WITH COUPLINGS
INCH-POUND --59226 1 December 2006 SUPERSEDING --59226 18 May 1998 COMMERCIL ITEM DESCRIPTION HOSE SSEMLY, NONMETLLIC, FIRE FIGHTING, WITH COUPLINGS The General Service dministration has authorized the
More informationAmphenol MIL-DTL-83723, Series III, Pyle
Amphenol MIL-DTL-83723, Series III, Pyle TALE OF CONTENTS MIL-DTL-83723, Series III, Pyle : Design Features, Customer Options, Manufacturer s Specifications. 363, 364 Quick Reference of Choices - Threaded
More information