EN Page 1/9 EGT-TD Lubricant approvals latest version:
|
|
- Maurice Booker
- 5 years ago
- Views:
Transcription
1 EN Page 1/9 Change information: Chap. /page Description (changes to the previous edition) Modification no. General 1.3 / / / 6 SEW lubricants added. Lubricant supplier Texaco deleted. Chapter lubricant change intervals added. Oil supply systems extended. Specifications on radial oil seals extended.
2 EN Page 2/9 Table of contents 1. Introduction/area of application Explanations of the structure of the tables and abbreviations Explanations on the individual lubricants Lubricant change intervals Explanations on oil supply systems and their viscosity Compatibility of lubricants with radial oil seals Industrial gear units (X.F, X.K, P, XP, P-X )... 7
3 EN Page 3/9 1. Introduction/area of application The present document describes the approved lubricants for SEW EURODRIVE industrial gear units (helical gear units, bevel-helical gear units and planetary gear units). The approvals are valid worldwide. SEW accepts no liability if different lubricants are used in the gear units and/or they are used outside of the recommended temperature ranges. Lubricants for industrial gear units are subject to approval. The approval will be made according to the document "Supplier approval for qualification and approval of lubricants gear unit oils" in its current version. NOTE: Printed documents may not include the latest changes. For the latest version of this document, refer to Explanations of the structure of the tables and abbreviations Viscosity class Note on special approvals Gear unit type Abbreviations: Mineral lubricant Synthetic lubricant CLP CLP HC E Mineral oil Synthetic hydrocarbons (PAO) Oil based on esters Lubricant for the food industry (NSF H1-compliant) Biodegradable oil (lubricant for agriculture, forestry, and water management) 1) Lubricants must only be used if service factor is F s 1.3 2) In the low temperature range, oil seals can withstand shaft deflections (e. g. through overhung load) only to a limited extent. Especially pulsating and changing radial displacements of the shaft must be avoided or limited. Please contact SEW-EURODRIVE if required. RWDR Radial oil seal
4 EN Page 4/9 1.2 Explanations on the individual lubricants Lowest cold start temperature for splash lubrication* Lowest cold start temperature for drives with pumps up to a max. oil viscosity of 5000 mm²/s* Lowest cold start temperature for drives with pumps up to a max. oil viscosity of 2000 mm²/s* Trade name Logo xyz +65 SEW Manufacturer Highest oil sump temperature** Approvals * In case of low temperatures, the oil must be heated to the specified minimum temperature, for example by using an oil heater. The maximum permitted oil viscosity per pump type can be found in chapter 1.4. ** The service life will be considerably reduced when exceeded. Observe the lubricant change intervals according to chapter Lubricant change intervals The following image depicts the change intervals for standard gear units under normal ambient conditions. In case of special designs under severe/aggressive ambient conditions, change the lubricant more frequently. [7] [6] [1] Operating hours [4] CLP HC/CLP HC NSF H1 [2] Sustained oil bath temperature [5] CLP (CC)/E Average value per oil type at 70 C [6] SEW GearOil Base [3] CLP PG/CPL PG NSF H1 [7] SEW GearOil Poly (H1)
5 EN Page 5/9 1.4 Explanations on oil supply systems and their viscosity Type Name Supplier Maximum oil viscosity [mm2/s] Picture Comment Shaft end pump for pressure lubrication SEP 5000 Flanged on the gearbox housing Shaft end pump for pressure lubrication SEP 2000 Mounted inside the vertical agitator gearbox housing Motor pump for pressure lubrication ONP 2000 Motor pump for pressure lubrication ONP 2000 Motor pump for pressure lubrication (light) ONP1L 5000 Motor pump for pressure lubrication ONP Device for oil cooling by air OAC 2000 Motor pump an heat exchanger for pressure lubrication and cooling by air OAP 2000 Device for oil cooling by water OWC 2000 Motor pump an heat exchanger for pressure lubrication and cooling by water OWP 2000 Device for oil cooling by air OAC Motor pump an heat exchanger for pressure lubrication and cooling by air OAP Device for oil cooling by water OWC Motor pump an heat exchanger for pressure lubrication and cooling by water OWP1 5000
6 EN Page 6/9 1.5 Compatibility of lubricants with radial oil seals SEW : A lubricant especially recommended by SEW EURODRIVE, also in regard of compatibility with the approved oil seals. The lubricant exceeds the state-of-the-art requirements. Limitations of use of radial oil seals with the specific lubricant are indicated in the following table: Material class Manufacturer Material Permitted oil sump temperature S 1 NBR 2 FKM 1 Freudenberg 72 NBR C 2) to +80 C 2 Trelleborg 4NV11-40 C 2) to +80 C 1 75 FKM C 2) to +115 C 1 Freudenberg 2 75 FKM C 2) to +115 C 2 Trelleborg 1 VCBVR -25 C 2) to +115 C Example 1: S11 - Only the elastomer Freudenberg 72 NBR 902 meets the requirements of the SEW EURODRIVE approval in regard of the specific lubricant. Example 2: S2 - Only the elastomer FKM meets the requirements of the SEW EURODRIVE approval in regard of the specific lubricant.
7 CLP Supplier Approval EN Page 7/9 2. Industrial gear units (X.F, X.K, P, XP, P-X ) Typ / Type Öltyp / Oil Type ISO, SAE NLGI X P VG 150 1) VG 220 VG 320 VG 460 VG 680 VG Mobilgear 600 Base 150 E 1 BM 150 SP 150 CLP 150 Plus HighGear 150 XP 150 GEM N Mobilgear 600 Shell Base 220 E 1 BM 220 SP 150 CLP 220 Plus HighGear 220 XP 220 GEM N Oil F 220 EP Mobilgear 600 Shell Base 320 E 1 BM 320 SP 320 CLP 320 Plus HighGear 320 XP 320 GEM N Oil F 320 EP Mobilgear 600 Shell Base 460 E 1 BM 460 SP 460 CLP 460 Plus HighGear 460 XP 460 GEM N Oil F 460 EP Base 680 E 1 BM BM 1000 SP 680 CLP 680 Plus HighGear 680 Mobilgear 600 XP 680 GEM N EP 680 NOTICE: The thermal application limits of radial oil seal materials (chapter 1.5) have to be considered as well. SEW-EURODRIVE GmbH & Co KG Postfach 3023 D Bruchsal Tel.(07251) 75-0 Fax(07251) Für diese Unterlagen behalten wir uns alle Rechte vor / Copyright reserved / Tous droits de modification réservés
8 CLP HC Supplier Approval EN Page 8/9 Typ / Type Öltyp / Oil Type ISO, SAE NLGI VG 32 1) SHC VG 68 1) Unisyn CLP 68 SHC 626 GEM 4-68 N S4 GX 68 X... VG 150 1) syn EP 150 Synthetic X 150 Unisyn CLP 150 SHC 629 SHC Gear 150 GEM N S4 GX 150 SH VG syn EP 220 Synthetic X 220 Unisyn CLP 220 HighGear Synth 220 SHC 630 SHC Gear 220 GEM N S4 GX 220 SH 220 VG syn EP 320 Synthetic X 320 Unisyn CLP 320 HighGear Synth 320 SHC 632 SHC Gear 320 GEM N S4 GX 320 SH P VG syn EP 460 Synthetic X 460 Unisyn CLP 460 HighGear Synth 460 SHC 634 SHC Gear 460 GEM N S4 GX 460 SH VG Synthetic X 680 Unisyn CLP 680 HighGear Synth 680 SHC 636 SHC Gear 680 GEM N S4 GX 680 SH 680 VG SHC 639 SHC Gear 1000 EG NOTICE: The thermal application limits of radial oil seal materials (chapter 1.5) have to be considered as well. SEW-EURODRIVE GmbH & Co KG Postfach 3023 D Bruchsal Tel.(07251) 75-0 Fax(07251) Für diese Unterlagen behalten wir uns alle Rechte vor / Copyright reserved / Tous droits de modification réservés
9 E CLP HC NSF H1 Supplier Approval EN Page 9/9 Typ / Type Öltyp / Oil Type ISO, SAE NLGI X VG 68 1) Cassida Fluid HF 68 Optileb HY UH1-68 N P VG 220 1) VG 460 1) VG Cassida Fluid GL Cassida Fluid GL 460 Optileb GT 220 SEW Optileb GT 460 SEW NOTICE: The thermal application limits of radial oil seal materials (chapter 1.5) have to be considered as well S2 Plantogear 460 S S UH1-220 N +95 4UH1-460 N Klüberbio CA2-460 SEW-EURODRIVE GmbH & Co KG Postfach 3023 D Bruchsal Tel.(07251) 75-0 Fax(07251) Für diese Unterlagen behalten wir uns alle Rechte vor / Copyright reserved / Tous droits de modification réservés
Approved Suppliers
EN Page 1/8 Change information: Chap. /page Description (changes to the previous edition) Modification no. Page 7 CLP HC 320 / Mobil SHC Gear 320 / highest oil bath temperature changed from 95 C to 100
More informationAddendum to the Assembly and Operating Instructions
Drive Technology \ Drive Automation \ System Integration \ Services *2276652_1216* Addendum to the Assembly and Operating Instructions Industrial Gear Units X.. Series Helical and Bevel-Helical Gear Units
More informationAddendum to the Assembly and Operating Instructions
Drive Technology \ Drive Automation \ System Integration \ Services *235971_317* Addendum to the Assembly and Operating Instructions Industrial Gear Units X.. Series Helical and Bevel-Helical Gear Units
More information5 Lubrication, Cooling and Heating
Overview of the and cooling types Lubrication, and Heating.1 Overview of the and cooling types The following combinations of and cooling types are possible. Lubrication Splash with shaft end pump /SEP
More information5 Lubrication, Cooling, and Heating
Lubrication,, and Heating Overview of the and cooling types Lubrication,, and Heating.1 Overview of the and cooling types The following combinations of and cooling types are possible. Lubrication Splash
More informationAddendum to the Assembly and Operating Instructions
Drive Technology \ Drive Automation \ System Integration \ Services *205516_017* Addendum to the Assembly and Operating Instructions Industrial Gear Units Motor Pump with Pressure Lubrication /ONP1L Edition
More information5 Lubricants. Lubricants Guidelines for lubricant selection. 5.1 Guidelines for lubricant selection STOP
Guidelines for lubricant selection Lubricants. Guidelines for lubricant selection Unless a special arrangement is made, SEW-EURODRIVE delivers the planetary gear unit without an oil fill and the primary
More informationAddendum to the Assembly and Operating Instructions
Drive Technology \ Drive Automation \ System Integration \ Services *2100516_017* Addendum to the Assembly and Operating Instructions Industrial Gear Units Motor Pump with Pressure Lubrication /ONP1 Edition
More information8 Design and Operating Notes
Lubricants Design and Operating Notes.1 Lubricants General information Unless a special arrangement is made, SEW-EURODRIVE supplies the drives with a lubricant fill adapted for the specific gear unit and
More information6 Design and operating notes
Error! B ookmark not d efined.error! Boo kmark not defin ed. Error! B ookmark not d efined.error! Boo kmark not defin ed. and operating notes Lubricants and operating notes.1 Lubricants.1.1 General information
More informationGearmotors and Gear Reducers
Gearmotors and Gear Reducers OPERATING INSTRUCTIONS 01 805 52 US GENERAL These operating instructions are intended to help you install and operate the drive. For trouble free service, proper installation
More informationPOWER GEAR. The high performance bevel gearbox.
MS-Graessner GmbH & Co. KG THE GEAR COMPANY The high performance bevel gearbox Precision combines with performance. Bevel gear technology is at the heart of an assembly consisting of gear housing, shafts,
More informationPOWER GEAR The high performance bevel gearbox
MS-Graessner GmbH & Co. KG THE GEAR COMPANY The high performance bevel gearbox Precision combines with performance. Bevel gear technology is at the heart of an assembly consisting of gear housing, shafts,
More informationKS TWINGEAR. Compact, precise and powerful.
MS-Graessner GmbH & Co. KG THE GEAR COMPANY Compact, precise and powerful Precision combines with performance. Bevel gear technology is at the heart of an assembly consisting of gear housing, shafts, flanges
More informationDas Winkelgetriebe. Made in Germany. Service. bevel gearboxes. Miniature. gearboxes. Bevel. Hygiene-design. gearboxes. gearboxes.
Made in Germany Miniature bevel gearboxes Bevel gearboxes Das Winkelgetriebe Hygiene-design gearboxes Hypoid gearboxes Worm gearboxes Gearbox motors Servo gearboxes (precision gearboxes) Special gearboxes
More informationExamples of Applications
Examples of Applications Optimum positioning of the tooth contact pattern is essential for a precise, low-noise bevel gear pairing. Angular milling head with ground bevel gear set by MS-Graessner. High-transmission
More informationCatalogue geared motors. Edition 01/
Catalogue geared motors Edition 0/0 Page Gearboxes and Lubrication Standard fitting - BG and BF - BK and BS Position of the terminal box and the cabel entry - BG and BF - BK and BS Radial and axial forces
More informationX.. Series Helical and Bevel-Helical Gear Units
SEW-EURODRIVE Easy Guide Industrial Gear Units X.. Series Helical and Bevel-Helical Gear Units Edition 05/2018 24803731/ EN 2/16 Gear unit structure 1 Safety notes 2 Gear unit designs 3 Mounting positions
More information5 Gear units, types of installation, lubricant quantities. 5.1 Standard fitting positions/ types of installation for Bauer geared motors
26 5 Gear units, types of installation, lubricant quantities 5.1 Standard fitting positions/ types of installation for Bauer geared motors 5 27 28 5.2 Position of the terminal box and the cable entry points
More information6 Lubricants. 6 Design and Operating Notes. 6.1 Lubricants. General information
Lubricants Design and Operating Notes.1 Lubricants General information Unless a special arrangement is made, SEW supplies the drives with a lubricant fill adapted for the specific gear unit and mounting
More information6 Design and Operating Notes
Design and Operating Notes Lubricants Design and Operating Notes. Lubricants General information Unless a special arrangement is made, SEW-EURODRIVE supplies the drives with a lubricant fill adapted for
More information6 Design and Operating Notes
Lubricants and fill quantities GK 0 Design and Operating Notes. Lubricants and fill quantities General information Unless a special arrangement is made, SEW-EURODRIVE supplies the drives with a lubricant
More informationCatalog. Industrial Gear Units Planetary Gear Unit Series XP130 - XP250 Torque Range from 600 to 5200 knm * _0415*
Drive Technology \ Drive Automation \ System Integration \ Services *21249792_0415* Catalog Industrial Gear Units Planetary Gear Unit Series XP130 - XP250 Torque Range from 600 to 5200 knm Edition 04/2015
More information6 Design and Operating Notes
Reduced backlash gear units GSE Design and Operating Notes.1 Reduced backlash gear units Helical, parallel shaft helical and helical-bevel gear units with reduced backlash are available from gear unit
More informationOperating instructions Gear Boxes and Geared Motors ZUVERLÄSSIG ANTREIBEND EFFIZIENT
Operating instructions Gear Boxes and Geared Motors ZUVERLÄSSIG NTREIBEND EFFIZIENT Edition 05/2016 Table of contents 1. Introduction.............................................................................
More information3 Mounting Positions and Important Order Information
General information on mounting positions M1 Mounting Positions and Important Order Information.1 General information on mounting positions Mounting position designation SEW differentiates between si mounting
More informationSynthetic Gear Oil Selection Dennis Lauer
Synthetic Gear Oil Selection Dennis Lauer Synthetic gear oils are used whenever mineral gear oils have reached their performance limit and can no longer meet the application requirements; for example,
More information7 Design and Operating Notes
Lubricants Design and Operating Notes.1 Lubricants General information Unless a special arrangement is made, SEW-EURODRIVE supplies the drives with a lubricant fill adapted for the specific gear unit and
More informationBG8A and BG8B MATERIAL LIST
BG8A and BG8B HYDRAULIC WINCH MATERIAL LIST PACR WINCH DIVISION P.O. BOX 547 BROKEN ARROW, OK U.S.A. 7403 PHONE (98) 25-85 FAX (98) 259-575 www.paccarwinch.com LIT226 R4 4/2009 Printed in U.S.A. Copyright
More informationCatalog. Industrial Gear Units Helical and Bevel-Helical Gear Units ML..V..N Series Vertical mounting position Torque classes from 150 knm knm
Drive Technology \ Drive Automation \ System Integration \ Services Catalog Industrial Gear Units Helical and Bevel-Helical Gear Units ML..V..N Series Vertical mounting position Torque classes from 150
More informationInstallation and Maintenance Helical and Bevel Helical Gearboxes KUMERA POWER TRANSMISSION GROUP
Installation and Maintenance Helical and Bevel Helical Gearboxes KUMERA POWER TRANSMISSION GROUP KUMERA DRIVES OY Kumerankatu 2 FI-11100 Riihimäki FINLAND Tel. +358 20 755 4200 Fax +358 20 755 4220 E-mail
More informationEdition. Planetary Gear Units P..RF.., P..KF.. Series 12/2002. Operating Instructions X / EN
Planetary Gear Units P..RF.., P..KF.. Series Edition 12/2002 Operating Instructions 1055 291X / EN SEW-EURODRIVE Contents M1 M6 1 Important Notes... 4 2 Safety Notes... 5 2.1 Extended storage... 7 2.2
More informationKlübersynth GH 6 oils Synthetic gear and high temperature oils
Klübersynth GH 6 oils Benefits for your application The oils meet the requirements according to DIN 51 517 03, CLP. Corresponding gears can be switched to Klübersynth GH 6 oils without prior consultation
More informationPlanning Section. Environmental conditions. Different power supply. Industrial solutions
Planning Section 86 89 Environmental conditions Different power supply 90 Industrial solutions 91 Power calculation and selection of the Motorized Pulley for package transportation 93 Oil types and contents
More informationKlübersynth UH1 6 Synthetic high-performance gear oil for the food-processing and pharmaceutical industries with KlüberComp Lube Technology
Your benefits at a glance Registered as NSF H1 and certified according to ISO 21469 High scuffing protection Good wear protection for gears and rolling bearings High micropitting resistance Good shear
More informationStatic and dynamic oil compatibility tests for Freudenberg radial shaft seals to release the usage in FLENDER-gear units applications (Table T 7300)
- Page of 8 Test Documentation This document is a translation of Freudenberg Sealing Technologies (FST) internal test procedure FB 7 008. In case both documents contradict each other, the iginal German
More information2000HG NEW STYLE HELICAL GEAR RATIO MULTIPLIER. INSTALLATION AND MAINTENANCE MANUAL May 4, Indianapolis, Indiana (800)
2000HG NEW STYLE HELICAL GEAR RATIO MULTIPLIER INSTALLATION AND MAINTENANCE MANUAL May 4, 2017 Indianapolis, Indiana (800) 866-7973 e-mail: sales@sterlingelectric.com www.sterlingelectric.com 7997 Allison
More information5 Project Planning for Gear Units
General information Project Planning for Gear Units.1 General information The planning information provided in this catalog is primarily concerned with the special needs of EBD gear units. For detailed
More informationHandbuch für installation, betrieb und wartung Planetengetriebe
Italy Headquarters Installation, use and maintenance manual Manuale Installazione Uso e Manutenzione Riduttori Epicicloidali Installation, Operation and Service Manual Handbuch für installation, betrieb
More informationOperating Instructions
Operating Instructions Table of contents Table of contents... 1 1. Declaration... 1 2. Warranty and liability... 2 3. Gear description... 2 4. Gear types... 2 5. Safety... 3 5.1 General safety information...
More information314 ORDINARY MAINTENANCE MANUAL FOR. PGA series VERTICAL MOUNTING POSITION. Release A02/15
314 www.comerindustries.com ORDINARY MAINTENANCE MANUAL FOR PGA series VERTICAL MOUNTING POSITION Release A02/15 INDEX General information...page 3 Ordinary maintenance...page 4 Oil lubricant replacement...page
More informationRENISO TRITON SE/SEZ Synthetic refrigeration oils based on polyol esters (POE) for HFC/FC refrigerants
RENISO TRITON / Description The refrigeration oils of the RENISO TRITON / series are based on synthetic esters that were especially developed for use with chlorine-free, fluorinated hydrocarbons (HFC/FC).
More information6 Project Planning for Optional Accessories
Mounting flange on output shaft Project Planning for Optional Accessories.1 Mounting flange on output shaft Usage Gear units can be supplied with an EBD mounting flange on the LSS (option "/EF22" or "/EF21").
More informationAddendum to the Assembly and Operating Instructions
Drive Technology \ Drive Automation \ System Integration \ Services Addendum to the Assembly and Operating Instructions Explosion-Proof Industrial Gear Units Helical and Bevel-Helical Gear Units X.. Series
More informationXCEL Series of Turbine Mixers
TABLE OF CONTENTS - TABLE OF CONTENTS Bulletin 01-050 (Recommended bolting torques)..pg.1 Bulletin 02-135 (Installation of Mixer Drive Size 15 to 19)..Pg. 2 Bulletin 04-135 (Maintenance of Mixer Drive
More informationLubricating instructions for linear guideways and ballscrews
Lubricating instructions for linear guideways and ballscrews HIWIN GmbH Brücklesbünd 2 Tel. +49 (0)781 / 9 32 78-0 E-mail info@hiwin.de 77654 Offenburg Fax +49 (0)781 / 9 32 78-90 www.hiwin.de These lubricating
More informationCH150 HOIST MATERIAL LIST (05617)
CH150 HOIST MATERIAL LIST (05617) PACR WINCH DIVISION P.O. BOX 547 BROKEN ARROW, OK U.S.A. 74013 PHONE (918) 251-8511 FAX (918) 259-1575 www.paccarwinch.com LIT2239 R1 6/2005 Printed in U.S.A. Copyright
More informationMobil SHC Gear Series
Mobil SHC Gear Series Gear Oils Product Description Mobil SHC Gear Series is a line of exceptional performance, synthetic industrial gear oils designed to provide outstanding protection of gears and bearings,
More informationPowerful, naturally. Environmentally acceptable and biodegradable lubricants for the marine industry
your global specialist Detailed information Powerful, naturally. Environmentally acceptable and biodegradable lubricants for the marine industry Combine environmental and economic benefi ts with speciality
More informationM1..N, X and MD series Horizontal Helical and Bevel-Helical Gear Units
Drive Technology \ Drive Automation \ System Integration \ Services Industrial Gear Units M1..N, X and MD series Horizontal Helical and Bevel-Helical Gear Units 2 Industrial gear units from SEW-EURODRIVE
More informationM6 General notes on mounting positions R, F, K, S, W gear units
M M M General notes on mounting positions R, F, K, S, W gear units Preiskatalog Gear Unit Mounting Positions. General notes on mounting positions R, F, K, S, W gear units SEW-EURODRIVE differentiates between
More informationPLANTOGEAR S. Environmentally acceptable lubricating oil and EP industrial gear oil based on synthetic saturated esters.
Description PLANTOGEAR 100 S and 150 S products are environmentally acceptable industrial gear oils based on special saturated synthetic esters which guarantee high ageing resistance and excellent wear
More informationCatalog. Industrial Gear Units of the MC... Series. Edition 04/2005 D3.B / EN
Gearmotors \ Industrial Gear Units \ Drive Electronics \ Drive Automation \ Services Industrial Gear Units of the MC... Series D3.B00 Edition 04/2005 23790 / EN Catalog SEW-EURODRIVE Driving the world
More informationINSTRUCTIONS FOR USE FACE GEARBOXES
INSTRUCTIONS FOR USE FACE GEARBOXES TNC MTC-TC KTM ES Declaration of Conformity Producer: TOS ZNOJMO, akciová společnost Družstevní 3 CZ 669 02 Znojmo Equipment: Face gearboxes Type/ Modification:MTC,
More information2000HG R-SERIES IN-LINE HELICAL GEAR REDUCER
2000HG R-SERIES IN-LINE HELICAL GEAR REDUCER INSTALLATION AND MAINTENANCE MANUAL April 10, 2018 7997 Allison Avenue, Indianapolis, IN 46268 Website: www.sterlingelectric.com (800) 866-7973 FAX (317) 872-0907
More informationLUKOIL Marine Lubricants PRODUCTS.
LUKOIL Marine Lubricants PRODUCTS www.lukoilmarine.com 03 STRUCTURE 04 GENERAL 05 MAIN GRADES 06 SECONDARY GRADES MINERAL OILS SYNTHETIC OILS AND SPECIALITIES GREASES 10 SCOSITY CLASSIFICATION 11 SCOSITY
More informationHYDRAULICS& TRANSMISSIONS INDUSTRY
HYDRAULICS& TRANSMISSIONS INDUSTRY HYDRAULIC OILS HYDRAULIC OILS, MINERAL LUKOIL GEYSER ST 10 Prod.-Nr.: 572510 LUKOIL GEYSER ST 22 Prod.-Nr.: 572520 LUKOIL GEYSER ST 32 Prod.-Nr.: 572530 LUKOIL GEYSER
More informationOperating Instructions
ISO 9001 ISO 9001 Gear Units OIVCE0101/0514 Operating Instructions Contents Contents... 02 1 - How to Use This Manual... 04 2 - Unit Designation... 05 2.1- Detailed Unit Designation... 05 2.2- Nameplate,
More informationTechnical Information
CYCLO 6 5 Technical Information Technical Information Technical Information 5.1 CYCLO 6 Lubrication Cyclo are either Grease lubricated or Oil lubricated. Refer to pages 5.3 and 5.4 to determine the unit
More informationFAMILY OF PRODUCTS MEROPA GEAR OILS CHEVRON LUBRICANTS CAN HELP YOU RUN BETTER LONGER
FAMILY OF PRODUCTS MEROPA GEAR OILS CHEVRON LUBRICANTS CAN HELP YOU RUN BETTER LONGER LUBRICANTS FOR MEROPA GEAR OILS We understand the maintenance value drivers in gear lubrication. Let us help your organization
More informationDanfoss Bauer GmbH Esslingen BA GB
Danfoss Bauer GmbH 73726 Esslingen Operating instructions Direct current permanent magnet geared motors BA 148 04 GB 1 Installation The drive must be assembled and connected by qualified personnel (skilled
More informationRENOLIN CLP PLUS Long-term approved special gear oils with extremely high ageing stability and excellent detergency (DD) selfcleaning
Long-term approved special gear with extremely Description Special lubricants are designed to solve problems and to guarantee trouble-free working at severe ambient conditions. The products of the RENOLIN
More informationyour global specialist Powerful, naturally. Environmentally acceptable and biodegradable lubricants for the marine industry
your global specialist Powerful, naturally. Environmentally acceptable and biodegradable lubricants for the marine industry Combine environmental and economic benefits with speciality lubricants from Klüber
More informationMobil SHC 600 Series. Exceptional Performance Gear and Bearing Oils. Product Description. Features and Benefits
Mobil SHC 600 Series Exceptional Performance Gear and Bearing Oils Product Description Mobil SHC 600 Series lubricants are exceptional performance gear and bearing oils designed to provide outstanding
More informationWorm Gear Reducers Installation, Lubrication and Maintenance Instructions
Selection Information Read ALL instructions prior to operating reducer. Injury to personnel or reducer failure may be caused by improper installation, maintenance or operation. Written authorization from
More informationyour global specialist Powerful, naturally. Environmentally acceptable and biodegradable lubricants for the marine industry
your global specialist Powerful, naturally. Environmentally acceptable and biodegradable lubricants for the marine industry Combine environmental and economic benefi ts with speciality lubricants from
More informationProduct Description. Mobil SHC 600 Series. Mobil Industrial, Canada. Exceptional Performance Gear and Bearing Oils
Mobil SHC 600 Series Page 1 of 6 Mobil SHC 600 Series Mobil Industrial, Canada Exceptional Performance Gear and Bearing Oils Product Description Mobil SHC 600 Series lubricants are exceptional performance
More informationyour global specialist Powerful, naturally. Environmentally acceptable and biodegradable lubricants for the marine industry
your global specialist Powerful, naturally. Environmentally acceptable and biodegradable lubricants for the marine industry Combine environmental and economic benefi ts with speciality lubricants from
More informationPLANTOGEAR S. Environmentally acceptable lubricating oil and EP industrial gear oil based on synthetic saturated esters.
Description PLANTOGEAR S products are environmentally acceptable industrial gear oils based on special saturated synthetic esters which guarantee high ageing resistance and excellent wear protection -
More informationCertified Quality System UNI EN ISO 9001 : 2008 SERVICE MANUAL PGRF series Release A10/14
312 Certified Quality System UNI EN ISO 9001 : 2008 www.comerindustries.com SERVICE MANUAL PGRF series Release A10/14 INDEX GENERAL INFORMATION... 3 GEARBOX UNIT IDENTIFICATION... 3 RISKS AND PRECAUTIONS...
More informationAddendum to the Operating Instructions
Drive Technology \ Drive Automation \ System Integration \ Services *25821946_0918* Addendum to the Operating Instructions Gear Unit Series R..7, F..7, K..7, K..9, S..7, SPIROPLAN W TorqLOC Plus Hollow
More informationInstallation and Maintenance. Helical and Bevel Helical Gear Units KUMERA POWER TRANSMISSION GROUP
Installation and Maintenance Helical and Bevel Helical Gear Units KUMERA POWER TRANSMISSION GROUP 2/37 Gear unit installation and maintenance 84 80 27A Kumera Drives Oy Headquarters Kumerankatu 2 FI-11100
More informationFUCHS WINDPOWER DIVISION is a comprehensive service provider to the wind power industry.
FUCHS WINDPOWER DIVISION is a comprehensive service provider to the wind power industry. Individual selection and evaluation of lubricants based on lubricant recommendations and analyses. Full documentation
More informationOperating Manual. STRÖTER Gear drives Page 1 from 34
Operating Manual STRÖTER Gear drives 03.2013 Page 1 from 34 Contents 1. Information 1.1 General advice 1.2 Safety and labeling 1.3 Intended use 1.4 Safety advice 1.5 Pre-delivery 1.6 Transport 1.7 Disposal
More informationRevision. Mechatronic Drive System MOVIGEAR DBC-B, DAC-B, DSC-B, SNI-B, * _0315*
Drive Technology \ Drive Automation \ System Integration \ Services *21931585_0315* Revision Mechatronic Drive System MOVIGEAR DBC-B, DAC-B, DSC-B, SNI-B, Edition 03/2015 21931585/EN SEW-EURODRIVE Driving
More informationBA EN.A0= L force Geared Motors. Ä.A0=ä. Operating Instructions GST, GFL, GKS/GKL, GKR, GSS. Gearbox
BA 12.0023 EN.A0= L force Geared Motors Ä.A0=ä Operating Instructions G GST, GFL, GKS/GKL, GKR, GSS Gearbox Product key Legend for product key Gearbox type GST GFL GKS/GKL GKR GSS Helical gearbox Shaft
More informationGENERAL INSTRUCTIONS RETAIN FOR FUTURE USE
GENERAL INSTRUCTIONS RETAIN FOR FUTURE USE U10000-1 of 2 1. Importance of the operating instructions These operating instructions are intended to provide general information and safety guidelines. It is
More informationExternal gear pump Series G
External gear pump Series G RE 10 093/04.14 Replace RE 10 093/06.13 AZPG-22 Fixed pumps V = 22.5...100 cm 3 / rev Overview of contents Contents Page General 2 Product overview 3 Ordering code single pumps
More informationManufacturing in accordance with GMP standards Klüber lubricants for the pharmaceutical industry. Lubrication is our world
Manufacturing in accordance with GMP standards Klüber lubricants for the pharmaceutical industry Lubrication is our world The company Industrial sector Special knowledge Detailed information Klüber speciality
More informationCheck valve type ER and EK
Check valve type ER and EK Product documentation Plug-in valve Operating pressure pmax: Flow rate Qmax: 700 bar 120 lpm D 7325 05-2015-1.0 by HAWE Hydraulik SE. The forwarding and reproduction of this
More information* _1015* Drive Technology \ Drive Automation \ System Integration \ Services. Revision. Drive Unit MGF..-DSM
Drive Technology \ Drive Automation \ System Integration \ Services *22325816_1015* Revision Drive Unit MGF..-DSM Edition 10/2015 22325816/EN SEW-EURODRIVE Driving the world Contents Contents 1 Revision...
More informationMOTORIZED PULLEYS UNIT HANDLING
2 ED. MOT EN 03/14 2 ED. MOT EN 03/14 MOTORIZED PULLEYS UNIT HANDLING GENERAL CATALOGUE MOTORIZED PULLEYS UNIT HANDLING GENERAL CATALOGUE AXIS & Stuifmeel BV Coenecoop 1 2741 PG Waddinxveen Netherlands
More informationTable A-c Standard PAO oils for FLENDER helical, bevel-helical, planetary gear boxes and 'Marine gear units without multi-disk clutches'
Approved lubricants --- Freigegebene Schmierstoffe Table A-c Standard PAO oils for FLENDER helical, bevel-helical, planetary gear boxes and 'Marine gear units Tabelle A-c Standard-PAO-Öle für FLENDER Stirnrad-,
More informationGear Motors. Series PGM Fixed Displacement Motors, Aluminium Designs
Gear Motors Series PGM Fixed Displacement Motors, Aluminium Designs aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding
More informationKlübersynth EG 4 oils
Benefits for your application Scuffing load capacity conforms to API GL 4 Miscible with mineral oil Excellent corrosion protection Ageing resistance Description The are fully synthetic high-performance
More informationSolutions for the Dairy Industry
Solutions for the Dairy Industry 2 CASSIDA food grade lubricants Solutions for the Dairy Industry CASSIDA food grade lubricants In the dairy industry, the use of food-safe machine lubricants can mean the
More informationBA EN.=A. Ä.=A.ä. Operating Instructions. Gearbox. Type 12. / 52.
BA 12.0028 EN.=A. Ä.=A.ä Operating Instructions Gearbox Type 12. / 52. Product key Gearboxes 1 2... Product group Product family Gearbox size Design Geared motors 1 2... Product group Product family Gearbox
More informationParts and Service Memo. Grease Selection. Calibration PSM JAW MSC. October 1, 2013 PSM JAW MSC
Parts and Service Memo PSM 025 1310 JAW MSC SUBJECT: Jaw Crushers. Jaw Bearing Lubrication Intervals. As a followup to PSM 022 released November 2012, this bulletin is to remind users of KPI-JCI Legendary
More informationMobilgear 600 XP Series
Mobilgear 600 XP Series Gear Oil Product Description The Mobilgear 600 XP Series are extra high performance gear oils having outstanding extreme pressur Mobilgear 600 XP Series is designed to stay ahead
More information2 Product description
Error! B ookmark not d efined.error! Bookmark not defin ed. Product description Product features Product description.1 Product features.1.1 Operating temperatures Gear units and gearmotors from SEW-EURODRIVE
More informationGROUP Woodcliff Lake, NJ October 2001
GROUP 11 11 08 98 Woodcliff Lake, NJ October 2001 Engine Service Engineering This Service Information bulletin supersedes S.I. 11 08 98 dated June 2000 and replaces S.I.02 12 98 dated June 2000. SUBJECT
More informationAn alternative approach to Synthetic Wind Turbine Gear Oil formulation. Phil Hutchinson. Evonik Oil Additives, Singapore.
An alternative approach to Synthetic Wind Turbine Gear Oil formulation. Phil Hutchinson. Evonik Oil Additives, Singapore. 1 Synthetic Industrial Gear-Oils / Wind Turbine Gear-oils (WTGO) MT Synthetics
More informationOPERATING INSTRUCTIONS. E Series Worm Gearboxes OIECE
OPERATING INSTRUCTIONS Worm Gearboxes OIECE0300-048 Contents Contents... 02 - How To Use This Manual... 04 2- Type Designation... 05 2. Detailed unit designation... 05 2.2 Nameplate unit designation...
More informationSpecial lubricants for wind turbines Product selection. Lubrication is our world. The company Industrial sector Special knowledge Detailed information
Special lubricants for wind turbines Product selection Lubrication is our world The company Industrial sector Special knowledge Detailed information Klüber special lubricants always a good choice Lubricants
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.
More informationHIGH PRESSURE FILTERS DF/DFF 1500 Series Inline Filters 6090 psi up to 250 gpm
HIGH PRESSURE FILTERS DF/DFF 1500 Series Inline Filters 6090 psi up to 250 gpm Hydraulic Symbol DFF FILTER REVERSE FLOW CIRCUIT Bypass Valve Filter Element Pop-up Indicator Features Available in T ported
More informationSeamer Lubrication. Suggestions, Requirements. & Specifications. By Pneumatic Scale Angelus
Seamer Lubrication Suggestions, Requirements & Specifications By Pneumatic Scale Angelus CAUTION: Contact your lubricant suppliers to verify the compatibility of lubricant with paints and components on
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.
More informationSEALING SOLUTIONS FOR YOUR DRIVES
Intelligent Drivesystems, Worldwide Services SEALING SOLUTIONS FOR YOUR DRIVES EN SEALING SYSTEMS FOR NORD GEAR UNITS AND GEARED MOTORS SEALING SYSTEMS FOR NORD GEAR UNITS AND GEARED MOTORS NORD DRIVESYSTEM
More information3.3 VARIABLE DISPLACEMENT MECHANICAL COMPENSATION
. VRIBL ISPLMNT MHNIL OMPNSTION ONTNTS PVV101 Ordering ode..1 Mechanical compensation Technical Information..2 Specifications.. Hydraulic fluids..4 Viscosity range..5 Temperature range..6 Seals..7 Filtration..8
More information