This block will potentially be used for the following types of deployments: See Reference 3.2.3, Section B.3.5 for descriptions of operations.
|
|
- Clifford Blake
- 5 years ago
- Views:
Transcription
1 Digitally Signed 25-Nov-2014 Digitally Signed 25-Nov-2014
2 1. Abbreviations MCD MPT NBL NSF UNOLS 2. Purpose Maximum Capability Document Maximum Permissible Tension Nominal Breaking Load National Science Foundation University-National Oceanographic Laboratory System This document describes the general arrangement of the oceanographic winch turning block that serves the oceanographic winch storage winch level winds onboard the vessel. It establishes the load capacity of the block as a component of the aft overboarding system. This document sets the maximum permissible tension (MPT) as required by the UNOLS RVSS, Appendix B when the sheave is used to support over-the-side operations for science. The tension member employed in the system is considered a component of the entire handling system and shall be used in accordance with Appendix A Deployment Types This block will potentially be used for the following types of deployments: Towing Surface Towing Mid-Water Towing Deep Water Station Keeping Surface Station Keeping Mid-Water Station Keeping Deep Water Operation /N Notes See Reference 3.2.3, Section B.3.5 for descriptions of operations. 3. General 3.1. Description A turning block in the Aft Winch Room routes wire between the oceanographic level winds and slack wire compensator components of the aft overboarding system. Winch Turning Block MCD, Rev. - Page 2 of 7 Job No , 15 October 2014
3 3.2. Reference Documents CFR , Wet Weight Handling Gear Rope and Cable Safe Working Load Standards, University National Oceanographic Laboratory System (UNOLS), UNOLS Research Vessel Safety Standards (RVSS), Appendix A, March Overboard Handling Systems Design Standards Criteria for the Design and Operations of Overboard Handling Systems, University National Oceanographic Laboratory System (UNOLS), UNOLS Research Vessel Safety Standards (RVSS), Appendix B, March Deck Sheave DS-D1220 Dimensional Sketch, Rapp Hydema, Drawing No. RH313983, Rev. A, 20 August Traction Winch System TRW-4000B + 2x RWS-2326/Spooling Device Principal Arrangement, Rapp Hydema, Drawing No. RH310356, Rev. B, 8 February Overside Equipment Handling Arrangement, Marinette Marine Corp., Drawing No , Rev. D Factory Acceptance Test, Ocean System Final Report, Rapp Hydema, 28 November Operational Requirements Maximum capabilities meet the following requirements: Item Maximum Capability Value Criteria Source Maximum Permissible Tension (MPT) 11,600 lbf 1 Reference Wire Groove Size 0.680" or 9/16" Rapp-Hydema Wrap Angles (α) Minimum 175 Rapp-Hydema Maximum 180 Rapp-Hydema Other Sheave speed range {Vendor Supplied} Spec min is 60 m/min Notes: 1. The level wind is on the low tension side of the traction winch; therefore, it will not be subject to the breaking load of the wire and is not required to meet the requirements of Reference Error! Reference source not found.. Therefore, the MPT of the level wind will not limit the MPT of the system. Winch Turning Block MCD, Rev. - Page 3 of 7 Job No , 15 October 2014
4 5. Operational Figures 5.1. Load Geometry Wrap Angle α Winch Turning Block MCD, Rev. - Page 4 of 7 Job No , 15 October 2014
5 5.2. Vendor Drawing Winch Turning Block MCD, Rev. - Page 5 of 7 Job No , 15 October 2014
6 This page has been intentionally left blank. Winch Turning Block MCD, Rev. - Page 6 of 7 Job No , 15 October 2014
7 R/V SIKULIAQ Maximum Capability Document Summary Oceanographic Winch Turning Block DS-D1220 Manufactured By: Rapp Hydema Reference Drawing Number: RH Prepared By: The Glosten Associates & Rapp Hydema Company D 171 ISO VIEW ( 1 : 15 ) D ROOT Ø1220 C Ø C B B 27 THRU 50 1 (10x) A REV ZONE DESCRIPTION DATE(d/m/y) APPROVED A * fixed, ready for production AXA Design A Weight 250 kg DECK SHEAVE Phone: (+47) DS- D1220 Fax: (+47) Scale Sheet office@rapphydema.com 1:10 1 / 1 DIMENSIONAL SKETCH Drw number RH Material (for part) Status Preliminary Drawn by / Date(dd/mm/yy) Checked by / Date(dd/mm/yy) Partlist RHTTS Maximum Permissible Tension = 11,600 lbf Note 1 The storage drums are on the low tension side of the traction winch; therefore, they will not be subject to the breaking load of the wire. Therefore, the MPT will not limit overboarding operations. This summary is provided for reference. It is the operator s responsibility to understand the limits and assumptions as presented in the full Maximum Capability Document. Winch Turning Block MCD, Rev. - Page 7 of 7 Job No , 15 October 2014
This oceanographic level winds will potentially be used for the following types of deployments:
Digitally Signed 25-Nov-2014 Digitally Signed 25-Nov-2014 1. Abbreviations MCD Maximum Capability Document MPT Maximum Permissible Tension NBL Nominal Breaking Load NSF National Science Foundation UNOLS
More informationThis slack line tensioner will potentially be used for the following types of deployments:
Digitally Signed 25-Nov-2014 Digitally Signed 25-Nov-2014 1. Abbreviations MCD MPT NBL NSF UNOLS 2. Purpose Maximum Capability Document Maximum Permissible Tension Nominal Breaking Load National Science
More informationSIKULIAQ & RCRV Scope of Supply
SIKULIAQ & RCRV Scope of Supply R/V Sikuliaq Scope of Supply Rapp Marine Winch Systems: Oceanographic Traction Winch System Two Hydrographic Winches Pentagon Research Control and Monitoring Systems Triplex
More informationWire and Cable Subcommittee Report. Rich Findley UNOLS RVTEC 2007
Wire and Cable Subcommittee Report Rich Findley UNOLS RVTEC 2007 Committee Members Richard Findley Matt Hawkins? Everything You Didn t Really Want To Know About Conductor Wire Basic Characteristics Part
More informationNDA-25B MKI Fast Rescue Boat Davit
NDA-25B MKI Fast Rescue Boat Davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Norsafe Project No.: TBA Norsafe Doc. No.: TSD-0039 Rev. Date: 14.11.2016 Rev. No: 2 Tel: +47 37 05 85 00 Fax: +47 37 05
More informationOcean Class AGOR Update. FIC Mee4ng March, 2015 J.M. Prince
Ocean Class AGOR Update FIC Mee4ng March, 2015 J.M. Prince Status on Test, Trials and Delivery R/V Neil Armstrong (AGOR 27) Undergoing Builder s Sea Trials Last Week Vendor Grooming, power runs, maneuvering
More informationWoods Hole Oceanographic Institution. Overview Report of DESH 5 Hydro Winch Testing on R/V ATLANTIS. May Upgrade and Renovation
Woods Hole Oceanographic Institution Overview Report of DESH 5 Hydro Winch Testing on R/V ATLANTIS May 2013 2012 2013 Upgrade and Renovation R/V Atlantis Upgraded Markey DESH 5 Hydro Winches May 2013 Page
More informationRV Investigator Long Core System. Mark Lewis. Senior Mechanical Technician
RV Investigator Long Core System Mark Lewis. Senior Mechanical Technician Overview My experience with these systems is limited so I have been talking to as many people around Australia and New Zealand
More informationE-150 MKI - Single Pivot Gravity Davit
E-150 MKI - Single Pivot Gravity Davit Norsafe Project No.: TBA Norsafe Doc. No.: TSD-0054 Rev. Date: 14.10.2016 Rev. No: 4 Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47
More information2.0 TECHNICAL SPECIFICATION:!
0 of 6 HYDRAMARIN 2.0 TECHNICAL SPECIFICATION: 2. OPERATION ENVIRONMENT: Area classification: Safe zone Description: Offshore/Marine environment, open deck Operation temperature range: -20 - + 45 degrees
More informationCrane Inspection Log. Mailing Address: P.O. Box Tulsa, OK Phone: (918) Fax: (918)
999978000 Crane Inspection Log Mailing Address: P.O. Box 581510 Tulsa, OK 74158-1510 Physical Address: 4707 North Mingo Road Tulsa, OK 74117-5904 Phone: (918) 836-0463 Fax: (918) 834-5979 www.autocrane.com
More informationNOAA Trawl and Longline Workshop
NOAA Trawl and Longline Workshop Usage of Auto Trawl during survey Rapp incorporates the following standard auto trawl features: Measurement of wire lengths and winch speed Measurement of wire tension
More informationAssessment Report. Science Winch System Assessment CGC HEALY (WAGB 20) USCG Surface Forces Logistics Center 4/4/2011 4/8/2011.
Assessment Report Prepared for USCG Surface Forces Logistics Center CGC HEALY (WAGB 20) 4/4/2011 4/8/2011 Science Winch System Assessment Submitted by: : April 4, 2011 Arrived onboard the vessel at 0730.
More informationReferences MERCHANT & TOWING VESSELS
Page 1/ 7 - Rapp Marine references MERCHANT & TOWING VESSELS VESSEL/ Project SCOPE OF SUPPLY MODEL 2017 Baydelta Navigation Ltd. Chartering LLC Tugboat Caden Foss The Tugboat is designed by Jensen Maritime,
More informationOcean Class AGOR Acquisition Update. UNOLS Council June 6, Harvard University
Ocean Class AGOR Acquisition Update UNOLS Council June 6, 2012 Harvard University Ocean Class AGOR Shipyard: Dakota Creek Industries Anacortes, WA Design Agent Guido Perla & Associates Seattle, WA 1 1
More informationLONG CORE-CDH port 250,000 # 42m 87M
AGOR 27 JPC LONG CORE-CDH 2007-2014 port 250,000 # 42m 87M $ NEW *HANDLING *CORE HARDWARE *ROPE SYSTEM OVERVIEW: SYSTEM OVERVIEW: Core Barrel system- The new core barrels are fabricated from a high strength
More informationNDA-25 MKI - Rescue Boat Davit
NDA-25 MKI - Rescue Boat Davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Norsafe Project No.: TBA Norsafe Doc. No.: TSD-0038 Rev. Date: 11.10.2016 Rev. No: 3 Tel: +47 37 05 85 00 Fax: +47 37 05 85
More informationMARINE EQUIPMENT. marine equipment marine equipment 97
MARINE EQUIPMENT 96 marine equipment marine equipment 97 Powerpack Total weight (without wire) 2.280 mm 1.280 mm 1.863 mm 2.500 kg Diesel engine Number of cylinders 4 Power 71 kw RPM 1.800 Cooling Radiator
More informationNDSC-34 MKI - Rescue Boat Davit
NDSC-34 MKI - Rescue Boat Davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Norsafe Project No.: TBA Norsafe Doc. No.: TSD-0048 Rev. Date: 14.11.2016 Rev. No: 3 Tel: +47 37 05 85 00 Fax: +47 37 05 85
More information4600 SERIES 3 RINGER SERIES 2. Manitowoc Cranes, Inc. Manitowoc, Wisconsin U.S.A.
Liftcrane Capacities No. 35 thru 1 Degree Static Machine LIFTING CAPACITIES: Lifting capacities are for a RINGER when operating on a barge. Machine shall be positively secured to prevent shifting. Lifting
More informationFred. Olsen POWER GENERATION AT SEA. Autonomous Sea Power «POWER AND GATEWAY SUBSEA» Fred.Olsen Ltd.
Author: Even Hjetland even.hjetland@fredolsen.no Date: Sept. 5th 2017 Revision: Type: O For email/download «POWER AND GATEWAY SUBSEA» Fred. Olsen Autonomous Sea Power POWER GENERATION AT SEA POWER SUPPLY
More informationWINCHES EQUIPMENT & SYSTEMS MAKING IT SIMPLE
WINCHES EQUIPMENT & SYSTEMS MAKING IT SIMPLE OUR WINCHES OTD offers three main categories of mooring winch solutions for the offshore industry: Standardized or tailor-made mooring winches and fairleads
More informationFred. Olsen POWER GENERATION AT SEA. Autonomous Sea Power. Fred.Olsen Ltd.
Author: Even Hjetland even.hjetland@fredolsen.no Date: Dec. 12th 2017 Revision: Type: Q For email/download Fred. Olsen Autonomous Sea Power POWER GENERATION AT SEA POWER SUPPLY AND COMMUNICATION PLATFORM
More informationDECK EQUIPMENT LAUNCH SYSTEM SALES BROCHURE
DECK EQUIPMENT LAUNCH SYSTEM SALES BROCHURE Last Updated: 18/05/2017 1 Contents LAUNCH SOLUTIONS FOR ROV S... 3 LAUNCH SOLUTIONS FOR TRENCHING ROV s... 4 LAUNCH SOLUTIONS FOR PLOUGHS... 5 A-FRAMES / GANTRY
More informationNRB-20 MKI Rescue boat davit
NRB-20 MKI Rescue boat davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85 01 E-mail: mail@norsafe.com Enterprise No.: NO940411696 www.norsafe.com 1. REGULATIONS
More informationSCC8100. Product Guide. FEATURES
SCC8100 Product Guide FEATURES 110 US T Capacity @ 12 ft 6 in Radius 29 ft 6 in - 59 ft 1 in Fixed Jib 220 ft Max Tip (H Main Boom) 20,944 lbs Main Winch - Rated Line Pull www.sanyamerica.com FEATURES
More informationCrawler Crane. 110 US Tons (100 Metric 12.5 ft Radius 223 ft (H) Main Boom Max Tip Height Main Boom & Fixed Jib Configurations.
SCC8100 Crawler Crane 110 US Tons (100 Metric Tons) @ 12.5 ft Radius 223 ft (H) Main Boom Max Tip Main Boom & Fixed Jib Configurations Product Guide KEY FEATURES OPERATORS CAB Sliding-door cab with large
More informationThe unique operating principle of the TREIBMATIC / 7
Increased performance in the ROTZLER universe: The unique operating principle of the / 7 TR 030, TR 080, TR 200, TR 350 TR 030 TR 080 TR 200 Content 1. Why? 3 ROTZLER Product description 3 The concept
More informationWT-64-M & WT-64-M-6 Brake Control Kit
WT-64-M & WT-64-M-6 Brake Control Kit Adjustable nuts Brake Band Clevis Existing Holes ¾ Thick Block Use C-6039 for WT-64-M-6 or Use C-5039 for WT-64-M 1-7/8 17/32 Drill Thru for mounting clevis-centered
More informationCable Pulling Winches kn KW 1002 KW 2002 KW 3002
Winches Chapter 1 Cable Pulling Winches 10-30 kn KW 1002 KW 2002 KW 3002 Cable Laying Machinery Pipe Renewal Winches Asphalt Recycler Accessories The winches of this series are ideal for seasonal contracts
More informationAnchor Handling/Towing Winches
Anchor Handling/Towing Winches TTS Offshore Handling Equipment delivers Anchor Handling/Towing Winches up to 600 tonnes. Our winches are designed to meet all anchor handling/towing requirements and are
More informationSeries 1300 Hydraulic Crane 30 Ton Load Ratings
Series 13 Hydraulic Crane Ton Load Ratings! DANGER AN UNTRAINED OPERATOR SUBJECTS HIMSELF AND OTHERS TO DEATH OR SERIOUS INJURY YOU MUST NOT OPERATE THIS CRANE UNLESS You have been trained in the safe
More informationTechnical specification for NDC 40 NO Rescue Boat Davit
Technical specification for NDC 40 NO Rescue Boat Davit 8.06.203 Re issued for construction PGO GNI GNI 0 25.04.203 Issued for construction PGO GNI GNI REV.: DATE: Reason for Issue / Description: Project
More informationPRELIMINARY. Product Guide. Crawler Crane
SCC8500 Crawler Crane PRELIMINARY 550 U.S. Tons (500 Metric Tons) @ 19.7 ft Radius 364.2 ft Max Tip Height (Main Boom) Main Boom, Fixed Jib and Luffing Jib Configurations Product Guide 2 SCC8500 Power
More informationWire Rope & Accessories
General Purpose & 19x7 CLASS ROPES MINIMUM BREAKING FORCE AND WEIGHTS FOR 19x7 ROPES Minimum Approx. breaking force Diameter wt./ft. (tons of (in.) (lbs.) 2,000 lbs.) XIP IWRC 3/16 0.064 1.57 1/4 0.113
More informationInstructor Guide. 215: Elevator: Mechanical Drive Systems Module 3: Gearless Drive Systems
PR EV IE W O N LY Instructor Guide 215: Elevator: Mechanical Drive Systems Module 3: Gearless Drive Systems Table of Contents Overview.......4 Gearless Drive Operation...8 Geared Vs. Gearless. 22 Summary..29
More informationTechnical specification for NDA 40 NO Rescue Boat Davit
Technical specification for NDA 40 NO Rescue Boat Davit 1.06.014 Weight information added PGO ESO GNI 1 18.06.013 Re issued for construction PGO GNI GNI 0 Issued for construction PGO GNI GNI REV.: DATE:
More informationLH-140 MKIII Lifeboat davit
LH-140 MKIII Lifeboat davit Norsafe AS P.O. Box 115 N-4852 Faervik, Norway Tel: +47 37 05 85 00 Fax: +47 37 05 85 01 E-mail: mail@norsafe.com Enterprise No.: NO940411696 www.norsafe.com 1. REGULATIONS
More informationFHP MANUFACTURING PARTS PRICE LIST
FHP MANUFACTURING PARTS PRICE LIST All models in this price sheet reflect our current vintage. For discontinued models please contact the factory. To ensure you receive the correct part please have the
More information(fairleaders) BALANCED HEAD FAIRLEADS DECK MOUNTED DOUBLE SHEAVE SHEAVE FAIRLEADS TYPE CFF BALANCED HEAD FAIRLEADS
FAIRLEADS 4.2.2. SHEAVE FAIRLEADS Pagina 1. (fairleaders) 2.2.1. BALANCED HEAD FAIRLEADS 2.2.2. DECK MOUNTED DOUBLE SHEAVE 2.2.3. SHEAVE FAIRLEADS TYPE CFF 2.2.4. BALANCED HEAD FAIRLEADS FAIRLEADS 4.2.2.
More informationSIDE RECOVERY SYSTEM (WRECKER) PARTS MANUAL
SIDE RECOVERY SYSTEM (WRECKER) PARTS MANUAL 1080 Hykes Road Greencastle, PA 17225 Phone (717) 597-7111 www.jerr-dan.com 5-376-000115 Rev 0 - May 01, 2008 2008 Jerr-Dan Corporation. All Rights Reserved.
More informationEmergency Tow Wire Storage Reel Pricing
Emergency Tow Wire Storage Reel 2016 Pricing Part number: ESR-60-23-24 HE Hot dipped galvanized frame with flame sprayed & epoxy coated drum $31,900.00 Part number: A-36BP: (recommended) One set blasted
More informationPOWER WINCHES 4HPF SERIES
4HPF SERIES Thern 4HPF series power winches feature helical/parallel, high efficiency gearing making them ideal for applications requiring long travel distances and faster line speeds. The enclosed, direct-drive
More informationMODEL : TM-1882 CRANE SPECIFICATIONS. MAXIMUM LIFTING CAPACITY lines)
DATE February, 2010 MODEL : TM-1882 CRANE SPECIFICATIONS MAXIMUM LIFTING CAPACITY 17,000kg@1.5m(6-part lines) BOOM WINCH SWING 6-sectioned, fully powered partly synchronized telescoping boom of pentagonal
More informationCartridge Valves Technical Information Directional Valves DCV 03
OVERVIEW DCV 03 directional control valves consist of: housing (1), control spool (5), with two centering springs (4), and cylindrical operating solenoids (2, 3). The three-position directional valves
More informationLaunch and Recovery Systems for ROV/Ts
Offshore, Advanced Load Handling Launch and Recovery Systems for ROV/Ts TECHNICAL INFORMATION Deck/skid-mounted overside LARS Overhead-mounted overside LARS Moonpool-based LARS 1 Operational profitability
More informationQuick guide. Pusnes TM deck machinery Hydraulic Winches
Quick guide Hydraulic Winches English 2 nd Edition 2010 Introduction The intention with this Quick Guide for TM deck machinery is to help prevent equipment damage caused by incorrect operation of the ships
More informationGrab System. BAUER GB 40 Hydraulic Grab Carrier
Grab System BAUER GB 40 Hydraulic Grab Carrier GB 40 Characterisation BAUER GB Line The BAUER GB 40 Hydraulic Grab Digging profits out of your projects Bauer s line of GB Hydraulic Grabs are a perfect
More informationABS Guide for Certification of Lifting Appliances 2016: Focus on machinery
ABS Guide for Certification of Lifting Appliances 2016: Focus on machinery Cernusco sul Naviglio, Italy 19 May 2016 Marine & Offshore Meeting 2016 Guide for Certification of Lifting Appliances Lifting
More informationEPA-EPC-EPF. Wire rope snatch blocks for material handling and man riding
1 / 5 Applications EPA/EPC/EPE/EPF/EPL pulleys are designed for man riding applications. They are in conformity with EN 1808. They can also be used for material lifting. These pulleys are mainly designed
More information2016 Load & Capacity Data Report
Caution and Disclaimer The contents of these materials are for information purposes and are provided as is without representation or warranty of any kind, including without limitation, accuracy, completeness
More informationCrawler Crane. 165 U.S. Tons (150 Metric 16.4 ft Radius 272 ft Max Tip Height (Main Boom) Main Boom & Fixed Jib Configurations.
SCC8150 Crawler Crane 165 U.S. Tons (150 Metric Tons) @ 16.4 ft Radius 272 ft Max Tip Height (Main Boom) Main Boom & Fixed Jib Configurations Product Guide The dependable way to lift your production Look
More informationY-fl'. MINISTRY OF TRANSPORT AND COMMUNICATIONS DEPARTMENT OF MARINE ADMINISTRATION
MINISTRY OF TRANSPORT AND COMMUNICATIONS DEPARTMENT OF MARINE ADMINISTRATION No-363/421, Corner of Merchant & Theinbyu Road, Botataung Township, Yangon, Myanmar E-mail : d gdma.mm@ gmail.com; dma.myan@smail.com
More informationRULES FOR THE CONSTRUCTION AND CLASSIFICATION OF SHIPS IDENTIFIED BY THEIR MISSION DREDGERSAND MUD BARGES SECTION 3 HULL EQUIPMENT CHAPTERS APPROACH
PART II RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF SHIPS IDENTIFIED BY THEIR MISSION TITLE 43 DREDGERSAND MUD BARGES SECTION 3 HULL EQUIPMENT CHAPTERS A B C D E F APPROACH DOCUMENTS, REGULATIONS
More informationCoast Guard s Fleet Renewal Plan 2017 November, 2017
Coast Guard s Fleet Renewal Plan 2017 November, 2017 Fleet Renewal Plan 2012 Under Way The Coast Guard is currently implementing its Fleet Renewal Plan 2012 and also planning for the future. The Fleet
More informationR.C. PLATH CO. Specialty Marine Hardware 2010 PLATH
R.C. PLATH CO. Specialty Marine Hardware 2010 PLATH Specialty Marine Hardware Portland, Oregon The finest accessories for adding safety, pleasure, and value to your craft. No craft too small or large for
More informationAdvances in winch system for defence applications
of Achievements in Materials and Manufacturing Engineering International Scientific Journal published monthly by the World Academy of Materials and Manufacturing Engineering Advances in winch system for
More informationTechnical File Engine Model: MD706MX (4.2L 230) - MD706MS (4.2L 200)
Engine Model: MD706MX (4.2L 230) - MD706MS (4.2L 200) Contents: 1 Components, settings and operating values of the engine which influence its NO x emissions Page 2 2 Full range of allowable adjustments
More informationFHP MANUFACTURING PARTS PRICE LIST
FHP MANUFACTURING PARTS PRICE LIST All models in this price sheet reflect our current vintage. For discontinued models please contact the factory. To ensure you receive the correct part please have the
More informationRoller chain idler sprocket units Idler pulley units
Roller chain idler sprocket units Idler pulley units Roller chain idler sprocket units, idler pulley units Page Product overview Roller chain idler sprocket units, idler pulley units... 334 Design and
More informationMcQuay. Central Station Air Handler. LHD, LML, LSL, LWL, LYF, MMM, MSL, MWL Vintage C. Last Manufactured: 1984
Replacement Parts List No. 055222700 Revision D 0/205 McQuay Central Station Air Handler LHD, LML, LSL, LWL, LYF, MMM, MSL, MWL 37-72 Vintage C Last Manufactured: 984 To find your Daikin Applied parts
More informationWave Energy for Powering Science. VIMS Industry Partnership Meeting. February 17, 2012
Wave Energy for Powering Science VIMS Industry Partnership Meeting February 17, 2012 Company Overview Commenced Operations: 1994 Incorporation: Delaware, USA Operating Locations: Pennington, NJ, USA and
More informationROV. Model SW01. Serial 12A. Enterprise 10, Singapore
USER MANUAL (Rev 1.0 11 June 2015) FOR ROV UMBILICAL SPOOLING SYSTEM Model SW01 Serial Number SW01-001 West Marine Technologies Pte Ltd 12A Enterprise Road Enterprise 10, Singapore 627681 wmt@westmarine.com.sg
More informationMan Rider and Personnel Lifting Winches
Man Rider and Personnel Lifting Winches Dedicated 150 kg (330 lb) Dual Purpose 920-5,000 kg (2,035-11,000 lb) When Tough Just Isn t Enough Dedicated 150 kg (330 lb) and Dual Purpose 920-5,000 kg (2,035-11,000
More informationSPECIFICATION. January, 2011
SPEC.F5-4711E2 DHP85-2, M65D Hydraulic Pile Driving Rig SPECIFICATION January, 2011 Nagoya, Japan Tel : 81- (52) - 623-3529 Fax: 81- (52) - 623-4349 Due to company policy of continuous development and
More informationSINCE CONDUCTOR HANDLING PRODUCTS TENSION STRINGING EQUIPMENT & ACCESSORIES CATALOGUE OUR PEOPLE CARE... OUR EQUIPMENT IS THE PROOF
SINCE 1947... CONDUCTOR HANDLING PRODUCTS TRANSMISSION DISTRIBUTION UNDERGROUND ACCESSORIES TENSION STRINGING EQUIPMENT & ACCESSORIES CATALOGUE Pulling For You Since 1947 Timberland Equipment specializes
More informationOcean Class AGOR. Baseline and Priorities Mission Equipment Specification (MES) 13 October 2010
Ocean Class AGOR Baseline and Priorities Mission Equipment Specification (MES) 13 October 2010 Baseline MES Strategy Ocean Class AGOR designs are being developed based on the MES contract attachment. This
More informationIOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA TEL: IMT PART NUMBER
CRANE LOG CALENDAR YEAR CRANE MODEL Daily Inspections Weekly Inspections Monthly Inspections Lubrication Record Maintenance Record Damage & Repair Record Modification Record Reference Specifications CRANE
More informationShipboard fittings and supporting hull structures associated with towing and mooring on conventional vessels ships
(Jan 2004) (Corr.1 Feb 2004) Rev.1 July 2004) (Rev.2 Sept 2006) (Rev.3 July 2007) (Corr.1 Sept 2014) (Rev.4 Oct 2016) Shipboard fittings and supporting hull structures associated with towing and mooring
More informationOptimising overall functionality of your ships integrated anchor handling, towing, mooring and subsea load handling solutions
Optimising overall functionality of your ships integrated anchor handling, towing, mooring and subsea load handling solutions Winches Operational profitability through pioneering technology, reliability
More informationHYDRAULIC TRUCK CRANE GT-600EX CARRIER : TC section, 11.0 m 43.0 m DIMENSION Overall length. approx. 13,170 mm Overall width
HYDRAULIC TRUCK CRANE SPEC. SHEET NO. GT-6E-1-31/EX-2 GT-6EX CARRIER : TC-42-2 GENERAL DATA CRANE CAPACITY 6, kg at 3. m BOOM 5-section, 11. m 43. m DIMENSION Overall length approx. 13,17 mm Overall width
More informationSPECIFICATIONS CENTURY MODEL 925 HYDRAULIC WRECKER
SPECIFICATIONS CENTURY MODEL 925 HYDRAULIC WRECKER 1.0 GENERAL DESCRIPTION The wrecker shall consist of a recovery boom, wrecker frame, modular type body, and a subframe for mounting to chassis. 1.1 The
More informationPRELIMINARY NEW! 186 kw. 40 t. Heavy Duty Cycle Crawler / Crane 41.1 m TIER IV
PRELIMINARY NEW! 1 kw 0 t Heavy Duty Cycle Crawler / Crane 1.1 m TIER IV Further developed. The E-Series. The characteristics of the E-Series 0 years of experience in the design and construction of duty
More informationFAR FROM THE COASTS, CLOSE TO THE BEST CHOICE YOU EVER MADE
FAR FROM THE COASTS, CLOSE TO THE BEST CHOICE YOU EVER MADE Absolute expertise, absolute accuracy, absolute reliability. Nothing else. M.E.P. Pellegrini Marine Equipments proposes a complete fshore crane
More informationTADANO MODEL TR-300XL-3-30 TON CAPACITY WORKING RANGE CHART. LIFTING CHARTS - Rough Terrain Cranes
LIFTING CHARTS - Rough Terrain Cranes TADANO MODEL - 30 TON CAPACITY WORKING RANGE CHART NOTE: Boom and jib geometry shown are for unloaded condition and machine standing level on firm supporting surface.
More informationSeries 1400A Hydraulic Crane 33 Ton
Series 1A Hydraulic Crane 33 Ton Load Ratings DANGER AN UNTRAINED OPERATOR SUBJECTS HIMSELF AND OTHERS TO DEATH OR SERIOUS INJURY YOU MUST NOT OPERATE THIS CRANE UNLESS You have been trained in the safe
More informationPS Strong and versatile
PS 8000 4.0 Strong and versatile Perfect solution For more than 5 decades, PALFINGER is in the business of knuckle boom lorry loader cranes and recognized as a Global Leader. The Global Leadership of PALFINGER
More informationSeries 1400 Hydraulic Crane 33 Ton Load Ratings
Series 1 Hydraulic Crane 33 Ton Load Ratings! DANGER AN UNTRAINED OPERATOR SUBJECTS HIMSELF AND OTHERS TO DEATH OR SERIOUS INJURY YOU MUST NOT OPERATE THIS CRANE UNLESS You have been trained in the safe
More informationTechnical specification for LH-230 Lifeboat Davit
Technical specification for LH-23 Lifeboat Davit Issued for information PGO GNI GNI REV.: DATE: Reason for Issue / Description: Norsafe Project No.: Project Title: Made By: Checked By: Project Approve
More informationROUGH TERRAIN CRANE TR-500M
TR ROUGH TERRAIN CRANE TR-500M JAPANESE SPECIFICATIONS OUTLINE 6-section Boom, 2-staged Power Tilt Jib X-type Outrigger SPEC. NO. TR-500M-3-00101 Control No. JA-03-35 - Return to INDEX TR-500M CRANE SPECIFICATIONS
More informationFor Sales Use Only! HTC 8650 Series II CRANE RATING MANUAL 4 SECTION POWER BOOM SERIAL NUMBER. not for crane operations
HTC 8650 Series II CRANE RATING MANUAL 4 SECTION POWER BOOM SERIAL NUMBER For Replacement, Order Part Number: L8P0001 (022603) Link Belt is a registered trademark. Page Contents 3 Operating Instructions
More informationOWNERS GUIDE 12V / 24V DC ELECTRIC WINCH. 12,000lb (6124kg) TWO SPEED VERY IMPORTANT
OWNERS GUIDE 12V / 24V DC ELECTRIC WINCH. 12,000lb (6124kg) TWO SPEED VERY IMPORTANT IT IS ESSENTIAL THAT YOU READ AND UNDERSTAND THIS GUIDE BEFORE INSTALLING AND OPERATING YOUR WINCH WINCHMAX UK WWW.WINCHMAX.CO.UK
More informationEMERGENCY TOWING ARRANGEMENTS HERMES" "HERACLES" & ZEUS INSTALLATION & MAINTENANCE
EMERGENCY TOWING ARRANGEMENTS HERMES" "HERACLES" & ZEUS 1) FOREWORD INSTALLATION & MAINTENANCE Emergency Towing Arrangements (ETA) "HERMES" & "HERACLES" are designed and produced by POSIDONIA SRL, Genoa
More informationOffshore Renewables: Expanding vessel capability to handle offshore renewable energy projects. Gregor McPherson Caley Ocean Systems
Offshore Renewables: Expanding vessel capability to handle offshore renewable energy projects Gregor McPherson Caley Ocean Systems Copyright Caley Ocean Systems Ltd 2012 Overview Caley Ocean Systems Offshore
More informationROUGH TERRAIN CRANE GR-160N
ROUGH TERRAIN CRANE GR-160N JAPANESE SPECIFICATIONS OUTLINE H-type Outrigger SPEC. NO. Control No. JA-01 GR-160N 1. Crane Specifications Crane Crane Capacity 6.5 m boom 16,000 kg x 3.0 m (6-part line)
More informationMODEL : GT-550EX EURO-2
DATE February, 2007 TADANO TRUCK CRANE MODEL : GT-550EX EURO-2 GENERAL DATA CRANE CAPACITY 55,000 kg at 3.0 m BOOM 5-section, 11.1 m 42.0 m DIMENSION MASS Overall length approx. 13,480 mm Overall width
More informationROUGH TERRAIN CRANE GR-500N
ROUGH TERRAIN CRANE GR-500N JAPANESE SPECIFICATIONS GR OUTLINE 6-section Boom, 2-staged Full Auto Jib X-type Outrigger SPEC. NO. GR-500N-1-00101 Control No. GR-500N-1-00101 / JA-03-1 - Return to index
More informationSCC8100. Product Guide. Crawler Crane <: ;VUZ 4L[YPJ ;VUZ ' M[ 9HKP\Z M[ / 4HPU )VVT 4H_ ;PW /LPNO[ 4HPU )VVT -P_LK 1PI *VUÄN\YH[PVUZ
SCC8100 Crawler Crane
More informationROUGH TERRAIN CRANE TR-500M
ROUGH TERRAIN CRANE TR-500M JAPANESE SPECIFICATIONS TR OUTLINE 6-section Boom, 2-staged Power Tilt Jib H-type Outrigger SPEC. NO. TR-500M-3-00113 Control No. JA-02 327 TR-500M CRANE SPECIFICATIONS CRANE
More informationROUGH TERRAIN CRANE TR-250M
TR ROUGH TERRAIN CRANE TR-250M JAPANESE SPECIFICATIONS OUTLINE 4-section Boom, 2-staged Power Tilt Jib X-type Outrigger SPEC. NO. TR-250M-6-00101 Control No. JA-02-61 - Return to INDEX TR-250M CRANE SPECIFICATIONS
More informationMcQuay. Central Station Air Handlers Low Pressure. LHD, LYF, LSL, LML, LWL Vintage C. LML, LSB Vintage E. Last Manufactured: 1999
Replacement Parts List No. 055222600 Revision F 11/2011 McQuay Central Station Air Handlers Low Pressure LHD, LYF, LSL, LML, LWL 103-228 Vintage C LML, LSB 106-111 Vintage E Last Manufactured: 1999 To
More informationANCHOR HANDLING AND TOWING SYSTEMS HUISMAN PRODUCT BROCHURE
ANCHOR HANDLING AND TOWING SYSTEMS HUISMAN PRODUCT BROCHURE NCHOR HANDL ND TOWING SY ANCHOR HANDLING AND TOWING SYSTEMS Huisman, the innovative offshore equipment supplier has developed a range of heavy
More informationOcean Class AGOR Program Program Status 21 October 2014
Ocean Class AGOR Program Program Status 21 October 2014 Prepared For UNOLS Annual Meeting Mike Prince (CTR) Research Facilities (321RF) Office of Naval Research Chris MacDonald Assistant Program Manager
More information2ND EXAM OF MAIN MACHINERY AND AUXILIARY MARINE SYSTEMS
2ND EXAM OF MAIN MACHINERY AND AUXILIARY MARINE SYSTEMS MASTER DEGREE IN NAVAL ARCHITECTURE AND MARINE ENGINEERING MECHANICAL ENGINEERING DEPARTMENT UNIVERSITY OF LISBON 28th JANUARY 2016 (Duration 3 hr)
More informationDesign: Aker OSCV 06L DSV Built: 2009 IMO No: Call sign: C6XW3 SKANDI ARCTIC DSV
Design: Aker OSCV 06L DSV Built: 009 IMO No: 94138 Call sign: C6XW3 SKANDI ARCTIC DSV IMO No 94138 The vessel is designed as a vessel for world wide operations Low resistance hull lines designed for speed
More informationShipboard fittings and supporting hull structures associated with towing and mooring on conventional ships
(Jan 2004) (Corr.1 Feb 2004) Rev.1 July 2004) (Rev.2 Sept 2006) (Rev.3 July 2007) (Corr.1 Sept 2014) (Rev.4 Oct 2016) (Corr.1 Dec 2016) (Corr.2 Mar 2017) Shipboard fittings and supporting hull structures
More informationDesign Criteria Data
OKLAHOMA CITY OK Latitude = 35.4 N WMO No. 72353 Longitude = 97.6 W Elevation = 133 feet Period of Record = 1973 to 1996 Average Pressure = 28.62 inches Hg Design Criteria Data Mean Coincident (Average)
More informationNational report of Japan (Submitted by Nobuyuki Shikama)
Argo Steering Team Meeting, Hyderabad, India, January 16-18, 2006 National report of Japan (Submitted by Nobuyuki Shikama) 1. Status of implementation 1.1 Floats deployed and their performance Japan Agency
More informationROUGH TERRAIN CRANE TR-250M
ROUGH TERRAIN CRANE TR-250M JAPANESE SPECIFICATIONS TR OUTLINE 4-section Boom, 2-staged Standard Jib X-type Outrigger SPEC. NO. TR-250M-6-00103 Control No. JA-02 371 TR-250M CRANE SPECIFICATIONS CRANE
More informationROUGH TERRAIN CRANE GR-250N
ROUGH TERRAIN CRANE GR-250N JAPANESE SPECIFICATIONS GR OUTLINE 4-section Boom, 2-staged Standard Jib X-type Outrigger SPEC. NO. GR-250N-1-00103 Control No. GR-250N-1-00103 / JA-04-1 - GR-250N CRANE SPECIFICATIONS
More information