Quick guide. Pusnes TM deck machinery Hydraulic Winches

Size: px
Start display at page:

Download "Quick guide. Pusnes TM deck machinery Hydraulic Winches"

Transcription

1 Quick guide Hydraulic Winches English 2 nd Edition 2010

2 Introduction The intention with this Quick Guide for TM deck machinery is to help prevent equipment damage caused by incorrect operation of the ships mooring winches. It also contains useful reminders about preparations and basic maintenance requirements. This booklet is not a replacement for the Maintenance or Instruction Manual, both of which the operator should be completely familiar with. It should be considered as an additional handy resource that can be kept in a pocket and available when needed. ONLY trained personal should perform anchoring and mooring operations. This to reduce equipment damage and hazardous situations, leading to serious injuries or loss of life. Read the Instruction Manual thoroughly so you are familiarised with the equipment. Always wear personal protective equipment!

3 1 of 18 Table of contents Before starting an Anchoring operation... 2 Inspect the Hydraulic Power Unit - HPU... 3 On deck preparations... 4 Anchor Winch operation... 5 Lower/ Walking Out the anchor with the winch motor... 6 Heave-in operation / adjustment of chain length... 7 After completion of heave-in operations Emergency release of anchor chain Mooring operation Before operation Inspect the Hydraulic Power Unit Manual mooring operation Warping end Automatic Mooring operation Testing of mooring drum brakes How to order Spare Parts? Abbreviations: HPU SOG Cable lifter Shackle, Shot Hydraulic Power Unit Speed Over Ground Chain handling part of windlass 27.5 m of anchor chain References: Effective mooring Anchoring Systems and Procedures for Large Tankers Both published by OCIMF - Oil Companies International Maritime Forum.

4 2 of 18 Before starting an Anchoring operation Be aware of the equipments limitations / design criteria. Keep in mind: Maximum pulling force for the anchor windlass is less than 10% of the chain breaking load. The windlass is not able to haul the vessel against wind and current or break-out an embedded anchor.. The windlass is only designed for heaving a free hanging anchor from a depth of m. With the windlass motor engaged, especially when heaving, the hydraulic motor is the weak link in the transmission system. Note the following: Max anchoring depth: 3 to 4 shackles (approx m). Speed over ground (SOG) not to exceed 0.3 knots (9 m/min) astern. Weather condition: Wind, current, waves and swell. NOTE! Waves and swells can induce hazardous dynamic forces into the anchoring system. Make sure you have communication equipment so you can have direct contact with the bridge at all times. Check the anchoring equipment s condition before operation. The most frequent failures for an anchor windlass are due to a lack of maintenance, especially adjustment for wear of the band brake linings and lack of lubrication.

5 3 of 18 Poorly adjusted windlass brakes or lack of maintenance can result in loss of anchor and chain, as the brake no longer will have sufficient holding power. Inspect the Hydraulic Power Unit - HPU Oil leakage. Reservoir oil level. Tank close-off valves need to be fully open (suction and pressure lines). Cooling water/air supply fully open/available. Alarms; Check the lamps by pressing the Lamp Test.

6 4 of 18 On deck preparations Correct: Check the brake lining thickness and the brake adjustments! Getting Critical Set indicator to marking (Hydraulic brake only) α always to be bigger than 0 degree Check the adjustment of the Stripper Bar Remove all lashings and coverings from chain stopper, hawse pipe and spurling pipe. Grease all lubrication points and the open gears. Remove and secure the chain stopper locking bolt and locking pin if there is one.

7 5 of 18 Anchor Winch operation General: Start HPU and select Stand-By High mode. Make sure that the vessel is not drifting off with a speed over ground (SOG) higher than 0.3 knots (9m/min) astern. Anchor Drop using the cable lifter brake; RECOMMENDED NOTE! Apply the cable lifter brake every time there is a stop in the anchoring operation. Engage the cable lifter unit to the winch and than insert the clutch locking pin if it is not a hydraulically operated clutch. Rotate the shaft in heave direction to take-up the slack in the transmission system. Release the cable lifter brake. Open the chain stopper dog/guillotine bar. Lower the chain till the anchor is at sea level. Apply the cable lifter brake and disengage the cable lifter unit from the anchor winch and insert locking pin, if it is not a hydraulically operated clutch. Open and close the cable lifter brake, dropping the anchor IN CONTROLLED STEPS. WARNING ABSOLUTELY AVOID too higher speed during anchor drop.

8 6 of 18 When the required chain length is paid out, apply the cable lifter brake, close the chain stopper dog/guillotine bar and insert the locking bolt and the securing pin if there is one. Forgot the locking bolt? Lower/ Walking Out the anchor with the winch motor Engage the cable lifter unit to the winch and insert the clutch locking pin, if it is not a hydraulically operated clutch. Rotate the shaft in heave direction to take-up the slack in the transmission system. Release the cable lifter brake. Open the chain stopper dog/guillotine bar. Lower the anchor by control of the winch motor in low speed only apply the cable lifter brake at all stops. Make sure the vessel is not drifting with a SOG higher than 0.3 knots astern. If required use the main engine to counteract.

9 7 of 18 When the required chain length is paid out, apply the cable lifter brake, close the chain stopper dog/guillotine bar and insert the locking bolt and the securing pin if there is one. Disengage the cable lifter from the anchor winch and insert the clutch locking pin, if it is not a hydraulically operated clutch. Manual clutch with locking pin Heave-in operation / adjustment of chain length If the paid out length of the chain has to be adjusted, or when the anchor heave-in operation has to be started, ensure minimum tension in the chain. Avoid high tension in chain when heaving.

10 8 of 18 The windlass is not designed for breaking out an embedded anchor or hauling the vessel as the motor is the weak link in the anchoring system. To break out the anchor, lock the chain in the chain stopper and use the vessels main engine. Potential damage of equipment when overloaded. Start the HPU and select Work Pressure mode. Engage the cable lifter unit to the anchor winch and insert the clutch locking pin if it is not a hydraulically operated clutch. Rotate the shaft in heave direction to take-up the slack in the transmission system. Release the cable lifter brake.

11 9 of 18 Too high tension in chain. Heave up position. No tension in chain. Break out an embedded anchor with main engine and chain locked in the chain stopper. Remove and secure the chain stopper locking bolt and locking pin if there is one. Open the chain stopper dog/guillotine bar.

12 10 of 18 Start to haul in the anchor in Low Speed mode. Remember the vessel should be manoeuvring towards the anchor, not the winch pulling it! Use the anchor chain washing system and observe the condition of the chain links and length markings. Reduce the speed before the anchor reaches the hawse pipe. When the anchor and flukes are properly stowed, stall the hydraulic motor while applying the band brake. Release the control lever once the cable lifter brake is fully applied. Close the chain stopper dog/guillotine bar and restore the locking bolt and securing pin if there is one. Disengage the winch clutch and insert the clutch locking pin, if it is not a hydraulically operated clutch. Shut down the HPU (Inspect alarms prior to shutdown). Switch HPU to "Stand-By Low" pressure for long waiting periods to avoid overheating the hydraulic oil. Stop the pumps when the work is completed. Overheating of the oil will stop the HPU automatically.

13 11 of 18 After completion of heave-in operations Lash the anchor with the lashing equipment and make sure that the anchor is fully secured in its "housed position". In case of hydraulically operated band brakes, check the brake setting according to the drawing below. Adjust if required with the hand wheel to set the marking to correspond with the indicator, see view X. For full details see the Instruction Manual. Check the brake lining thickness and the brake adjustment. Replace all covers and weather protections etc. on spurling and hawser pipes Grease all lubrication points and the open gears. Check condition and movement of the couplings/clutches. Notify the appropriate officer of any issues or observations made during the operation of the equipment.

14 12 of 18 Emergency release of anchor chain In case of black-out or lack of power, the anchor has to be dropped manually by using the windlass brake only. Remove lashing and all covers from spurling and hawse pipe. Check that the winch coupling is disconnected and clutch locking pin inserted if it is not a hydraulically operated clutch. Release/open the chain stopper, use a crowbar if necessary. Carefully release the cable lifter brake by turning the brake wheel counter clockwise. Control the speed manually in steps with the brake wheel. When sufficient chain is paid out, tighten the cable lifter brake. Close the chain stopper dog/guillotine bar and insert the locking bolt and securing pin if there is one. WARNING AVOID too higher speed during anchor drop.

15 13 of 18 Mooring operation WARNING The winch gear and motor is NOT designed to stop the vessel s motion at quay approach! Before operation Inspect the condition of the winches and grease all lubrication points, especially the mooring drum bearings, preferably have the shaft rotating and the drums disconnected. Check the condition of band brake lining and that it is correct adjusted. Check condition of the other items of mooring equipment.

16 14 of 18 Inspect the Hydraulic Power Unit. Oil leakage. Reservoir oil level. Tank close-off valves need to be fully open (suction and pressure lines). Cooling water/air supply is fully open/available. Alarms: Check the lamps by pressing the Lamp Test. Manual mooring operation. Start HPU and select Work Pressure mode. Engage the drum coupling and secure the coupling lever with the locking pin if it is not a hydraulically operated clutch. Rotate the main shaft in heave direction to take-up the slack in the gear transmission before releasing the brake. Coupling arm with locking pin Manual operated drum brake Hydraulic spring applied drum brake

17 15 of 18 Select Low Speed when tensioning the rope and High Speed or Auto Speed for slack rope operations. Switch HPU to "Stand-By Low" mode for long waiting periods to avoid overheating the hydraulic oil. Stop the pumps when the work is completed. Warping end. Never allow more then 3 to 4 turns on the warping end. WARNING! Never use high modulus synthetic fibre ropes under tension on the warping end due to the low friction coefficient in the rope. Avoid operating the warping end when there is tension in the mooring lines. Frequently use of warping end during mooring operation requires intermittent greasing of the mooring drum bearings. Never use the warping end for continuous mooring. To fairlead To fairlead Incorrect Correct Note! Always fix the line on a bollard in front of the warping end.

18 16 of 18 Too many layers on tension part and rope stored on the warping end Winch nominal pull, speed and brake holding load refers normally to the FIRST LAYER on drum. Use the split flange opening when changing from the storage to the tension part of the drum. When the winch operation is completed, engage the mooring drum brakes. Release the tension in the clutch and disengage the drum coupling. When adjusting tension, engage the clutch fully and rotate the shaft in heave direction to take-up the slack in the transmission system before releasing the mooring drum brake. Once the mooring operation is completed, shut down the HPU.

19 17 of 18 Automatic Mooring operation When automatic mooring is to be used the mooring plan has to take following precautions into consideration: Winches operating in the auto-mooring mode will have a recovery load about 0.55 times and a rendering load about times the nominal pulling load. One drum only to be connected to the winch gear. If two drums on the same winch are used in auto mooring mode, the resulting load must be equal to the total load for one drum! However, the individual tension in the two ropes will be unknown. Winches with multiple drums: One drum connected to winch gear, the remaining drums to be disengaged. Alternatively the mooring lines to be set on drum brake. Winches with multiple drums: Grease the drum bearings before operation. Intermittent greasing is necessary for long time operation! If bad weather, wind and current: Use the mooring drum brakes for the lines heading in to the wind and current. The remaining lines to be set in automatic mode; ONE LINE EACH WINCH! Never put all spring lines in automatic mooring mode, minimum one line to be kept on the drum brake. With both spring lines in automatic mode the vessels can start to walk along the quay.

20 18 of 18 Warping ends are not subject to automatic mooring activities. When berthing is completed, select which winches to be set in automatic mooring mode: Let only one pump run on the HPU to avoid overheated oil. Switch the hydraulic pressure to Stand-By High mode. Speed selection valve to be set to Low Speed. Lock the manoeuvring handle in Heave position. Check that the vessel is not drifting out of position. Testing of mooring drum brakes. When testing of the holding load for the mooring drum brakes is required, follow the instructions and procedures given in the Instruction Manual. How to order Spare Parts? For ordering spar parts, detailed instructions are given in the Spare Parts chapter of the Instruction Manual.

21 Probably the most experienced supplier of Deck Machinery in the world. More than units supplied since Reliable lifetime partner - 24/7 service network worldwide - Rugged design for harsh environment - Safe and easy operation Korea Aker Korea Co., Ltd Tel: office@pusnes.co.kr China Aker Solutions c/o Bee Fortune Co., Ltd. Tel: beechan@vip.163.com Aker AS, Tel: pusnes@akersolutions.com

22 Aker AS Tel: Singapore Tel: Middle East Tel: North America Tel: South America Tel: Lifecycle services academy

Optimising overall functionality of your ships integrated anchor handling, towing, mooring and subsea load handling solutions

Optimising overall functionality of your ships integrated anchor handling, towing, mooring and subsea load handling solutions Optimising overall functionality of your ships integrated anchor handling, towing, mooring and subsea load handling solutions Winches Operational profitability through pioneering technology, reliability

More information

IMPORTANT INFORMATION BEFORE USING YOUR 12V ELECTRIC WINCH

IMPORTANT INFORMATION BEFORE USING YOUR 12V ELECTRIC WINCH IMPORTANT INFORMATION BEFORE USING YOUR 12V ELECTRIC WINCH The responsibility for safe operation of this winch ultimately rests with the operator. Please read all operating instructions carefully before

More information

Introduction: Nelson Lau. MEP (Marine Equipment Product) is a Total System Solution Provider. With extensive

Introduction: Nelson Lau. MEP (Marine Equipment Product) is a Total System Solution Provider. With extensive Deck Machinery 1 Contents: Company Introduction...Page 03-04 MORDEC Winches.... Page 05-14 MORDEC Tugger Winch Page 15 MORDEC Combined Windlass /Winch... Page 16 MORDEC Anchor Handling/Towing Winch.. Page

More information

WINCHES EQUIPMENT & SYSTEMS MAKING IT SIMPLE

WINCHES EQUIPMENT & SYSTEMS MAKING IT SIMPLE WINCHES EQUIPMENT & SYSTEMS MAKING IT SIMPLE OUR WINCHES OTD offers three main categories of mooring winch solutions for the offshore industry: Standardized or tailor-made mooring winches and fairleads

More information

Anchor Handling/Towing Winches

Anchor Handling/Towing Winches Anchor Handling/Towing Winches TTS Offshore Handling Equipment delivers Anchor Handling/Towing Winches up to 600 tonnes. Our winches are designed to meet all anchor handling/towing requirements and are

More information

AU DU PONT DE LUTTRE BRUSSELS BELGIUM PHONE: FAX: OPERATING MANUAL. Electric Fully Automatic Floor Saw FS 1218 EX

AU DU PONT DE LUTTRE BRUSSELS BELGIUM PHONE: FAX: OPERATING MANUAL. Electric Fully Automatic Floor Saw FS 1218 EX AU DU PONT DE LUTTRE 74-1190 BRUSSELS BELGIUM PHONE: 322 34 83 162 FAX: 322 34 83 136 OPERATING MANUAL Electric Fully Automatic Floor Saw FS 1218 EX 2 Important information before you start! When the machine

More information

OVID Refresher Inspector Course. A Guide to the uniform inspection procedure OVID

OVID Refresher Inspector Course. A Guide to the uniform inspection procedure OVID OVID Refresher Inspector Course A Guide to the uniform inspection procedure OVID Presentation F, New Edition 2013 Mooring system components The brake band The wire The joining shackle The synthetic tail

More information

ANCHOR HANDLING AND TOWING SYSTEMS HUISMAN PRODUCT BROCHURE

ANCHOR HANDLING AND TOWING SYSTEMS HUISMAN PRODUCT BROCHURE ANCHOR HANDLING AND TOWING SYSTEMS HUISMAN PRODUCT BROCHURE NCHOR HANDL ND TOWING SY ANCHOR HANDLING AND TOWING SYSTEMS Huisman, the innovative offshore equipment supplier has developed a range of heavy

More information

PRODUCT IN STOCK SERIAL PRODUCT MODEL QUANTITY 1 ANCHOR HANDLING TOWING WINCH AHT2D H 2 2 ANCHOR HANDLING TOWING WINCH NCW-AHT2D H 3

PRODUCT IN STOCK SERIAL PRODUCT MODEL QUANTITY 1 ANCHOR HANDLING TOWING WINCH AHT2D H 2 2 ANCHOR HANDLING TOWING WINCH NCW-AHT2D H 3 PRODUCT IN STOCK SERIAL PRODUCT MODEL QUANTITY 1 ANCHOR HANDLING TOWING WINCH AHT2D-220-280-H 2 2 ANCHOR HANDLING TOWING WINCH NCW-AHT2D-300-400-H 3 3 ANCHOR WINDLASS MOORING WINCH AMW-GDDG-10-30-46K2-H

More information

Lbs Kgs Ft M

Lbs Kgs Ft M Installation Instructions for 92600 ATV Winch 3000 lb. Rated Pull SPECIFICATIONS Rated line pull: 3000 lbs. (1360kgs) single line Motor: Permanent magnetic DC 12V with 1.2 hp. /0.9kw output Gear: Differential

More information

Deck equipment for MPSV offshore vessels

Deck equipment for MPSV offshore vessels www.triplex.no Deck equipment for MPSV offshore vessels 2 www.triplex.no TRIPLEX, a MacGregor company, is a major supplier of cranes and handling equipment to Offshore-, Fishery and Research vessels. Quality

More information

ATV WINCH. Thank you for purchasing a

ATV WINCH. Thank you for purchasing a 1 2 ATV WINCH Thank you for purchasing a Winch. This manual covers operation and maintenance of the winch. All information in this publication is based on the latest production information available at

More information

ELECTRICAL WINCH 60SPS12 60SPS24

ELECTRICAL WINCH 60SPS12 60SPS24 ELECTRICAL WINCH 60SPS12 60SPS24 Assembly & Operating Instructions INTRODUCTION Congratulations on your purchase of a winch. We design and build winches to strict specifications and with proper use and

More information

OWNERS GUIDE 12V / 24V DC ELECTRIC WINCH. 12,000lb (6124kg) TWO SPEED VERY IMPORTANT

OWNERS GUIDE 12V / 24V DC ELECTRIC WINCH. 12,000lb (6124kg) TWO SPEED VERY IMPORTANT OWNERS GUIDE 12V / 24V DC ELECTRIC WINCH. 12,000lb (6124kg) TWO SPEED VERY IMPORTANT IT IS ESSENTIAL THAT YOU READ AND UNDERSTAND THIS GUIDE BEFORE INSTALLING AND OPERATING YOUR WINCH WINCHMAX UK WWW.WINCHMAX.CO.UK

More information

Megamarine Services Pte Ltd

Megamarine Services Pte Ltd Megamarine Services Pte Ltd Based in Singapore, Megamarine Services Pte Ltd is established by Mr. Chris Goh Ngak Eng in 2006, targeting to serve customer from Building & Construction, Marine & Offshore,

More information

Emergency Towing Booklet (ETB) According to SOLAS II-1, Reg. 3-4 and MSC.1/Circ. 1255

Emergency Towing Booklet (ETB) According to SOLAS II-1, Reg. 3-4 and MSC.1/Circ. 1255 Emergency Towing Booklet (ETB) According to SOLAS II-1, Reg. 3-4 and MSC.1/Circ. 1255 Table of Contents 1 GENERAL DESCRIPTION.. 3 1.1 GENERAL... 3 1.1.1 Flag or Class Aproval......3 1.2 LIMITATION DURING

More information

Megamarine Services Pte Ltd

Megamarine Services Pte Ltd Megamarine Services Pte Ltd Based in Singapore, Megamarine Services Pte Ltd is established by Mr. Chris Goh Ngak Eng in 2006, targeting to serve customer from Building & Construction, Marine & Offshore,

More information

ELECTRICAL WINCH 45EWHST12

ELECTRICAL WINCH 45EWHST12 ELECTRICAL WINCH 45EWHST12 Assembly & Operating Instructions CONTENTS INTRODUCTION... 1 GETTING TO KNOW YOUR WINCH... 2 SAFETY PRECAUTIONS... 3 GENERAL TIPS FOR SAFE OPERATION... 5 WINCHING TECHNIQUES

More information

I. General Safety Precautions

I. General Safety Precautions 1 2 ATV/UTV WINCH Thank you for purchasing a. This manual covers operation and maintenance of the winch. All information in this publication is based on the latest production information available at the

More information

A12000 ELECTRIC WINCH. Manual & Safety Instructions.

A12000 ELECTRIC WINCH. Manual & Safety Instructions. A12000 ELECTRIC WINCH Manual & Safety Instructions www.terrafirma4x4.com 0 PLEASE READ CAREFULLY BEFORE OPERATING THE WINCH Contents 1. Electric Winch Usage 03 2. Safety Warnings & Precautions 03 2.1 Danger

More information

Our windlass has a dynamic braking system for anchor lowering by hydraulic motor, and we can obtain about times of rated speed.

Our windlass has a dynamic braking system for anchor lowering by hydraulic motor, and we can obtain about times of rated speed. WINDLASS INDUSTRIAL STANDARDS FUKUSHIMA s standard types of windlass with mooring winch are designed and manufactured satisfied to the following regulations: JIS F 6713, ISO 4586: Hydraulic windlass JIS

More information

M A R I T I M E E N G I N E E R S P T Y L TD A Member of James Fisher and Sons plc

M A R I T I M E E N G I N E E R S P T Y L TD A Member of James Fisher and Sons plc O C E A N T O W I N G C O N D I T I O N S C H E C K L I S T T U G : T O W : P A R T 1 : T O W E D V E S S E L R E Q U I R E M E N T S DOCUMENTATION REQUIRED (FROM BARGE/TOWED VESSEL OWNERS) Certificate

More information

ABS Guide for Certification of Lifting Appliances 2016: Focus on machinery

ABS Guide for Certification of Lifting Appliances 2016: Focus on machinery ABS Guide for Certification of Lifting Appliances 2016: Focus on machinery Cernusco sul Naviglio, Italy 19 May 2016 Marine & Offshore Meeting 2016 Guide for Certification of Lifting Appliances Lifting

More information

COME.UP DV-15. Instruction manual.

COME.UP DV-15. Instruction manual. COME.UP DV-15 Instruction manual www.bigfoottrade.kz Automotive Winch Thank you for purchasing a Winch. This manual covers operation and maintenance of the winch. All information in this publication is

More information

دبي لحلول االستشعار. Active Load Brochure Load Cells

دبي لحلول االستشعار. Active Load Brochure Load Cells Active Load Brochure Load Cells www.dusense.ae +97148135972 info@dusense.ae Load Measuring Shackles DuSense is Middle-East Agent by Active Load to provide complete transducer solution designing and manufacturing

More information

WARNING. Electric Recovery Winch. General Safety Precautions

WARNING. Electric Recovery Winch. General Safety Precautions 1 Electric Recovery Winch Thanks for purchasing a WINCH. This manual covers operation and maintenance of the winch. All information in this publication is based on the latest production information available

More information

accidents which arise due to nonobservance and the safety information herein.

accidents which arise due to nonobservance and the safety information herein. 2000LB WINCH Model: 7247 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This dust often

More information

I. Safety Requirement WARNING. ATV/UTV Winch

I. Safety Requirement WARNING. ATV/UTV Winch 1 2 ATV/UTV Winch Thank you for purchasing a COMEUP Winch. This manual covers operation and maintenance of the winch. All information in this publication is based on the latest production information available

More information

Owner s Manual: PS4000 4,000 LB. WINCH

Owner s Manual: PS4000 4,000 LB. WINCH Owner s Manual: PS4000 4,000 LB. WINCH PIERCE ARROW INC. 549 U.S. HWY 287 S. HENRIETTA, TEXAS 76365 ---------------------------------------------------- TOLL FREE 800-658-6301 FAX 940-538-4382 ----------------------------------------------------

More information

C3500A WINCH Assembly & Operating Instructions

C3500A WINCH Assembly & Operating Instructions C500A WINCH Assembly & Operating Instructions INTRODUCTION Congratulations on your purchase of a high quality winch. We designs and builds winches to strict specifications and with proper use and maintenance

More information

Installation Instructions XRC 3.0 3,000lb Winch Part # 97203

Installation Instructions XRC 3.0 3,000lb Winch Part # 97203 Parts Included Qty Parts Included Qty Winch with Wire Rope 1 Remote Control 1 Winch Plate 1 Handle Bar Control 1 Clevis Hook 1 Hardware Pack 1 NOTE: Read, study and follow all instructions before operating

More information

ELECTRICAL WINCH S9500SD

ELECTRICAL WINCH S9500SD ELECTRICAL WINCH S9500SD Assembly & Operating Instructions CONTENTS INTRODUCTION... 1 GETTING TO KNOW YOUR WINCH... 2 SAFETY PRECAUTIONS... 3 GENERAL TIPS FOR SAFE OPERATION... 5 WINCHING TECHNIQUES A-Z...

More information

SHERPA 4x4 OWNER'S MANUAL

SHERPA 4x4 OWNER'S MANUAL www.sherpa4x4.com.au info@sherpa4x4.com.au SHERPA 4x4 OWNER'S MANUAL Copyright (C) Sherpa 4x4 www.sherpa4x4.com.au info@sherpa4x4.com.au 1 PLEASE READ WARNING! Your winch has a duty cycle and cannot be

More information

! DANGER Lb. Winch Mounting Instructions. Tools required: Before You Start. Assembly Instructions. General Information. Manual No.

! DANGER Lb. Winch Mounting Instructions. Tools required: Before You Start. Assembly Instructions. General Information. Manual No. 500 Lb. Winch Mounting Instructions For 400/4400 NT/ST, 40/440 ST And 40/440 ST Manual No. 70-86M Before You Start! When you see this symbol, the subsequent instructions and warnings are serious - follow

More information

Owner s Manual: PSHV SERIES WINCHES

Owner s Manual: PSHV SERIES WINCHES Owner s Manual: PSHV SERIES WINCHES PIERCE ARROW INC. 549 U.S. HWY 287 S. HENRIETTA, TEXAS 76365 -------------------------------------------------------TOLL FREE 800-658-6301 FAX 940-538-4382 -------------------------------------------------------www.piercearrowinc.com

More information

ELECTRICAL WINCH 6000EN

ELECTRICAL WINCH 6000EN ELECTRICAL WINCH 6000EN Assembly & Operating Instructions CONTENTS INTRODUCTION... 1 GETTING TO KNOW YOUR WINCH... 2 SAFETY PRECAUTIONS... 3 GENERAL TIPS FOR SAFE OPERATION... 5 WINCHING TECHNIQUES A-Z...

More information

Q-Series Stealth Winch

Q-Series Stealth Winch Q-Series Stealth Winch with Integrated Solenoid & Synthetic Winch Line Assembly and Installation Manual # 92122.204X READ ALL SAFETY MESSAGES AND UNDERSTAND ALL INSTRUCTIONS AND PROCEDURE NOTICES BEFORE

More information

PO Box 1719 Subiaco Western Australia

PO Box 1719 Subiaco Western Australia INSTRUCTION MANUAL Contact BUSH WINCHES AND ANCHORS PTY LTD PO Box 1719 Subiaco Western Australia 6904 Email: info@bushwinch.com.au CONGRATULATIONS Congratulations on your purchase of the Bush Winch. You

More information

Topaz Master. 85T BP M 5700 kw DP2 - AHTS. Vessel Specifications

Topaz Master. 85T BP M 5700 kw DP2 - AHTS. Vessel Specifications Topaz Master 85T BP - 64.8 M 5700 kw DP2 - AHTS Vessel Specifications Diesel-electric propulsion Lower fuel consumption, reduced environmental footprint 50-man accommodation - MLC compliant 420m 2 of clear

More information

ELECTRIC WINCH Manual and Safety Instruction

ELECTRIC WINCH Manual and Safety Instruction ELECTRIC WINCH Manual and Safety Instruction MODELS: A9500 and A9500S A12000 and A12000S X9500 and X12500 *PLEASE READ CAREFULLY BEFORE OPERATING THE WINCH CONTENT What s Included 01 Safety Warnings &

More information

ENGINE WINCHES from 300 to 5000 kg - TS and TD Series

ENGINE WINCHES from 300 to 5000 kg - TS and TD Series ENGINE WINCHES from 300 to 5000 kg - TS and TD Series INSTRUCTION MANUAL START-UP AND MAINTENANCE In an endeavor to improve its products, HUCHEZ reserves the right to alter the equipment described herein,

More information

A-Series ATV Winch Operator and Installation Manual

A-Series ATV Winch Operator and Installation Manual A-Series ATV Winch Operator and Installation Manual 1 P a g e A-Series Operator and Installation Manual Thank you for choosing Superwinch. Your Superwinch is a powerful machine and whether you use it for

More information

Northern Sales & Distribution Centre

Northern Sales & Distribution Centre User Manual Industrial Door Northern Sales & Distribution Centre The Door Centre, Discovery Park, Crossley Road, Stockport, SK4 5BW /indupart /indupart /indupart /company/indupart-ltd Foreword This user

More information

STUCK FAST? GET UNSTUCK FAST.

STUCK FAST? GET UNSTUCK FAST. 59 Winches STUCK FAST? GET UNSTUCK FAST. A TJM winch is the essential risk management tool when venturing to remote locations and upping the stakes of your 4WD adventure. TJM s range of new generation

More information

CONTENT. Winches 5 Chain Stoppers 13 Pool Anchors 14 Mooring Equipment 19 Service/Spare parts 22 Equipment Table 23

CONTENT. Winches 5 Chain Stoppers 13 Pool Anchors 14 Mooring Equipment 19 Service/Spare parts 22 Equipment Table 23 Catalogue 2 CONTENT Winches 5 Chain Stoppers 13 Pool Anchors 14 Mooring Equipment 19 Service/Spare parts 22 Equipment Table 23 3 Ship s Equipment Centre Groningen B.V. Founded in 1890 as Ten Horn Winches,

More information

DECK MACHINERY. Providing Engineering Systems and Solutions for the Marine and Offshore Industry

DECK MACHINERY. Providing Engineering Systems and Solutions for the Marine and Offshore Industry DECK MACHINERY Providing Engineering Systems and Solutions for the Marine and Offshore Industry Introduction: MEP (Marine Equipment Product) is a Total System Solu on Provider. With extensive contacts

More information

INSTRUCTIONS AND OPERATOR S GUIDE ELECTRIC WINCH STEALTH PLEASE READ CAREFULLY BEFORE OPERATE THE WINCH

INSTRUCTIONS AND OPERATOR S GUIDE ELECTRIC WINCH STEALTH PLEASE READ CAREFULLY BEFORE OPERATE THE WINCH INSTRUCTIONS AND OPERATOR S GUIDE ELECTRIC WINCH STEALTH 3000 PLEASE READ CAREFULLY BEFORE OPERATE THE WINCH Description Winch assembly with wire rope Hook and Handsaver Remote Switch Roller Fairlead Mounting

More information

2nd EDITION STEVPRIS FLIPPER DELTA DANFORTH AC-14 SWIVEL SHACKLE DETACHABLE PEARLINK HINGE LINK LINK

2nd EDITION STEVPRIS FLIPPER DELTA DANFORTH AC-14 SWIVEL SHACKLE DETACHABLE PEARLINK HINGE LINK LINK STEVPRIS FLIPPER DELTA DANFORTH AC-14 SWIVEL SHACKLE DETACHABLE PEARLINK HINGE LINK LINK SHACKLE GOLDNOSE CLOSED/OPEN SOCKET GRAPNEL J CHASER 2nd EDITION JS OFFSHORE SUPPLY PTE LTD 7500A Beach Road #13-304

More information

OPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE. Deck: Ship s Power Plants

OPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE. Deck: Ship s Power Plants Page 1 of 8 Compiled by Approved by Chief Examiner Syllabus Committee: 26 February 2013 OPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE Deck: Page 2 of 8 KNOWLEDGE, UNDERSTANDING

More information

The unique operating principle of the TREIBMATIC / 7

The unique operating principle of the TREIBMATIC / 7 Increased performance in the ROTZLER universe: The unique operating principle of the / 7 TR 030, TR 080, TR 200, TR 350 TR 030 TR 080 TR 200 Content 1. Why? 3 ROTZLER Product description 3 The concept

More information

installation, operation & maintenance instructions

installation, operation & maintenance instructions V3000 WINDLASS pacific simpson-lawrence installation, operation & maintenance instructions contents... 1.0 PARTS 1.1 Exploded Diagram 1.2 For Future Reference 1.3 Parts List 2.0 PLANNING THE INSTALLATION

More information

MARINE. Drives and motors for electrically driven deck machinery and offshore winches

MARINE. Drives and motors for electrically driven deck machinery and offshore winches MARINE Drives and motors for electrically driven deck machinery and offshore winches 2 MARINE BROCHURE Performance. Speed. Reliability. Safety. Everything counts. With the help of application expertise

More information

MARINE EQUIPMENT. marine equipment marine equipment 97

MARINE EQUIPMENT. marine equipment marine equipment 97 MARINE EQUIPMENT 96 marine equipment marine equipment 97 Powerpack Total weight (without wire) 2.280 mm 1.280 mm 1.863 mm 2.500 kg Diesel engine Number of cylinders 4 Power 71 kw RPM 1.800 Cooling Radiator

More information

03 MORDEC MORDEC MORDEC MORDEC MORDEC 15 MORDEC 16 MORDEC 17 MORDEC

03 MORDEC MORDEC MORDEC MORDEC MORDEC 15 MORDEC 16 MORDEC 17 MORDEC Cranes 1 Contents: Company Introduction...... Page 03 MORDEC Cranes.........Page 04-06 MORDEC Marine Deck Crane...Page 07-10 MORDEC Offshore Pedestal Crane...Page 11-12 MORDEC Offshore Lattice Boom Crane....Page

More information

DC Series Utility Winches Instruction Manual

DC Series Utility Winches Instruction Manual DC Series Utility Winches Instruction Manual To prevent SERIOUS INJURY, DEATH and PROPERTY DAMAGE, you should read, understand and follow the warnings and instructions in this manual. Keep for future reference.

More information

Design: KMAR 404 Built: 1998 IMO No:

Design: KMAR 404 Built: 1998 IMO No: Design: KMAR 404 Built: 1998 IMO No: 9166613 IMO No 9166613 Tank capacites Cargo Cement Mud Fuel Oil Fresh water Base Oil Brine Drill Water Oil Rec. Tank ID Contents Capacity (m 3 ) 2,400 2,500 0,900 1,000

More information

Owner s Manual: PS SERIES WINCHES

Owner s Manual: PS SERIES WINCHES Owner s Manual: PS SERIES WINCHES PIERCE ARROW INC. 549 U.S. HWY 287 S. HENRIETTA, TEXAS 76365 -------------------------------------------------------- TOLL FREE 800-658-6301 FAX 940-538-4382 --------------------------------------------------------

More information

RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF SHIPS IDENTIFIED BY THEIR MISSION DREDGERSAND MUD BARGES SECTION 3 HULL EQUIPMENT CHAPTERS APPROACH

RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF SHIPS IDENTIFIED BY THEIR MISSION DREDGERSAND MUD BARGES SECTION 3 HULL EQUIPMENT CHAPTERS APPROACH PART II RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF SHIPS IDENTIFIED BY THEIR MISSION TITLE 43 DREDGERSAND MUD BARGES SECTION 3 HULL EQUIPMENT CHAPTERS A B C D E F APPROACH DOCUMENTS, REGULATIONS

More information

Self-Recovery Winch WARNING. General Safety Precautions

Self-Recovery Winch WARNING. General Safety Precautions 1 Self-Recovery Winch Thank you for purchasing a Winch. This manual covers operation and maintenance of the winch. All information in this publication is based on the latest production information available

More information

Winch Trouble Shooting Guide

Winch Trouble Shooting Guide Winch Trouble Shooting Guide This guide has been compiled to help resolve common problems often experienced with winches. It is only a guide to help diagnose and correct some of the more common faults

More information

Recovery Winch Owner s Manual 1

Recovery Winch Owner s Manual 1 Recovery Winch Owner s Manual 1 2 Pierce Arrow 800-658-6301 Recovery Winch Owner s Manual The PS series winch is a powerful tool and must be used with extreme care. Deviating from the manual s instructions

More information

O C E A N T O W I N G C O N D I T I O N S C H E C K L I S T T U G : T O W :

O C E A N T O W I N G C O N D I T I O N S C H E C K L I S T T U G : T O W : O C E A N T O W I N G C O N D I T I O N S C H E C K L I S T T U G : T O W : In order that the survey can be conducted with the least inconvenience to the parties concerned, we list the below details that

More information

MAINTENANCE WORK INSTRUCTION. Mech OFF Replace Head Pulley CVXXX

MAINTENANCE WORK INSTRUCTION. Mech OFF Replace Head Pulley CVXXX OPF MAINTENANCE WORK INSTRUCTION PYXIS DOCUMENT CLEAN TEMPLATE SCOPE NOTE: SPECIAL TOOLING REQUIRED PREPARATION AND INFORMATION CVXXX Head Pulley The purpose of this document is to detail the safe replacement

More information

WARNING WARNING CAUTION. Warnings and Cautions MOVING PARTS ENTANGLEMENT HAZARD MOVING PARTS ENTANGLEMENT HAZARD CHEMICAL AND FIRE HAZARD

WARNING WARNING CAUTION. Warnings and Cautions MOVING PARTS ENTANGLEMENT HAZARD MOVING PARTS ENTANGLEMENT HAZARD CHEMICAL AND FIRE HAZARD Warnings and Cautions As you read these instructions, you will see S, S, NOTICES and NOTES. Each message has a specific purpose. S are safety messages that indicate a potentially hazardous situation, which,

More information

EMERGENCY TOWING ARRANGEMENTS HERMES" "HERACLES" & ZEUS INSTALLATION & MAINTENANCE

EMERGENCY TOWING ARRANGEMENTS HERMES HERACLES & ZEUS INSTALLATION & MAINTENANCE EMERGENCY TOWING ARRANGEMENTS HERMES" "HERACLES" & ZEUS 1) FOREWORD INSTALLATION & MAINTENANCE Emergency Towing Arrangements (ETA) "HERMES" & "HERACLES" are designed and produced by POSIDONIA SRL, Genoa

More information

Ramsey Winch Company OWNER S MANUAL BADGER Electric Winch Model BADGER Congratulations

Ramsey Winch Company OWNER S MANUAL BADGER Electric Winch Model BADGER Congratulations Ramsey Winch Company OWNER S MANUAL BADGER Electric Winch Model BADGER 2500 Note: Fairlead does not attach directly to winch. Winch shown with mounting plate, sold separately. BADGER 2500 WINCH LAYER OF

More information

5 CAR TRUCK SUPERSTRUCTURE DRIVERS INSTRUCTION MANUAL

5 CAR TRUCK SUPERSTRUCTURE DRIVERS INSTRUCTION MANUAL 5 CAR TRUCK SUPERSTRUCTURE DRIVERS INSTRUCTION MANUAL Britain s premier Car Transporter manufacturer FOR THE ULTIMATE IN QUALITY AND SERVICE PLEASE CONTACT US AT The Old Airfield, Gosfield, Halstead, Essex

More information

Technical data Hydraulic crawler crane HS 895 HD

Technical data Hydraulic crawler crane HS 895 HD Technical data Hydraulic crawler crane HS 895 HD Dimensions Basic machine with undercarriage R 9760 3650 10000 5480 3675 2445 1810 3950 1610 1700 7945 9360 3975 1720 R 6360 1100 6800 620 17380 Operating

More information

DECK EQUIPMENT LAUNCH SYSTEM SALES BROCHURE

DECK EQUIPMENT LAUNCH SYSTEM SALES BROCHURE DECK EQUIPMENT LAUNCH SYSTEM SALES BROCHURE Last Updated: 18/05/2017 1 Contents LAUNCH SOLUTIONS FOR ROV S... 3 LAUNCH SOLUTIONS FOR TRENCHING ROV s... 4 LAUNCH SOLUTIONS FOR PLOUGHS... 5 A-FRAMES / GANTRY

More information

M/V OCEAN SUPPLIER. Vestland Marine Sp. z o.o. Chwarznieńska str 87E, Gdynia, PL. ME 303 Anchor Handling Tug Supply Vessel (AHTS), DPS-1

M/V OCEAN SUPPLIER. Vestland Marine Sp. z o.o. Chwarznieńska str 87E, Gdynia, PL. ME 303 Anchor Handling Tug Supply Vessel (AHTS), DPS-1 ME 303 Anchor Handling Tug Supply Vessel (AHTS), DPS-1 Vestland Marine Sp. z o.o. Chwarznieńska str 87E, 81-602 Gdynia, PL Genera Anchor Handling Tug Supply Vessel; DPS-1 GENERAL SHIPS NAME CALL SIGN C6VL3

More information

DONGHAE MACHINERY & AVIATION Co., Ltd TECHNICAL SPECIFICATION MODEL SERIES

DONGHAE MACHINERY & AVIATION Co., Ltd TECHNICAL SPECIFICATION MODEL SERIES DONGHAE MACHINERY & AVIATION Co., Ltd TECHNICAL SPECIFICATION MODEL - 433 SERIES Model Series Revision 05 Date May 16, 2012 2 1. Terminology Diagram/L No. Description No. Description 1 Unit (Including

More information

ROUGH TERRAIN CRANE. Table of contents SPECIFICATION 1 LIFTING CAPACITIES. Stationary on rubber 2 Pick & carry m Boom+10.

ROUGH TERRAIN CRANE. Table of contents SPECIFICATION 1 LIFTING CAPACITIES. Stationary on rubber 2 Pick & carry m Boom+10. ROUGH TERRAIN CRANE Table of contents SPECIFICATION 1 LIFTING CAPACITIES 2 Stationary on rubber 2 Pick & carry 2 17.5m +6.5m SL Jib 3 17.5m +10.25m SL Jib 3 17.5m +14.0m SL Jib 3 32.5m +6.5m SL Jib 5 32.5m

More information

Technical data Hydraulic crawler crane HS 885 HD

Technical data Hydraulic crawler crane HS 885 HD Technical data Hydraulic crawler crane HS 885 HD Dimensions Basic machine with undercarriage R 6910 2850 8300 3500 2210 1420 4120 1400 1400 2725 5490 6750 2100 1000 4920 590 R 5520 15200 Operating weight

More information

ATV/UTV WINCH INSTRUCTION BOOK 3000 LBS

ATV/UTV WINCH INSTRUCTION BOOK 3000 LBS ATV/UTV WINCH INSTRUCTION BOOK 3000 LBS As you read these instructions, you will see WARNINGS and CAUTIONS. Each message has a specific purpose. WARNINGS and CAUTIONS identify the hazard, indicate how

More information

STRINGING EQUIPMENT CATALOGUE

STRINGING EQUIPMENT CATALOGUE Antenna Construc on Winches for li ing and passenger li ing STRINGING EQUIPMENT CATALOGUE PULLER FOR LIFTING PASSENGERS Model: SPW 2,5 - P Bull wheel Puller with integrated reel winder switchable between

More information

KATO KRM-13H. 13 TONNE HYDRAULIC SLEW CRANE Specification

KATO KRM-13H. 13 TONNE HYDRAULIC SLEW CRANE Specification KATO KRM-13H 13 TONNE HYDRAULIC SLEW CRANE Specification Height Length Width Regd Weight TARE 2.845 m 7.375 m 1.995 m 13140 kgs ROUGH TERRAIN CRANE CRANE Description Rough terrain crane with maximum lifting

More information

Technical data Hydraulic crawler crane HS 875 HD

Technical data Hydraulic crawler crane HS 875 HD Technical data Hydraulic crawler crane HS 875 HD Dimensions Basic machine with undercarriage R 5710 2580 8300 3500 2110 1300 1240 4020 1400 5330 2600 1000 530 6480 2240 4900 R 5520 14100 Operating weight

More information

Winches & Capstans. Air Electric Custom

Winches & Capstans. Air Electric Custom Winches & Capstans Air Electric Custom Engineered Winches 203Series High-performance engineered winches meet demanding application requirements. Unlimited Capability Each 203 Series winch is specifically

More information

ROUGH TERRAIN CRANE SPECIFICATION. CARRIER Carrier specification Maximum traveling speed 49km/h Grade ability

ROUGH TERRAIN CRANE SPECIFICATION. CARRIER Carrier specification Maximum traveling speed 49km/h Grade ability ROUGH TERRAIN CRANE CRANE Description Rough terrain crane with maximum lifting capacity 13 ton Crane specification 5.3 m 13,000kg 1.7 m (Parts of line : 8) 9.04 m 6,000kg 4.0 m (Parts of line : 4) 12.78

More information

WT-64-M & WT-64-M-6 Brake Control Kit

WT-64-M & WT-64-M-6 Brake Control Kit WT-64-M & WT-64-M-6 Brake Control Kit Adjustable nuts Brake Band Clevis Existing Holes ¾ Thick Block Use C-6039 for WT-64-M-6 or Use C-5039 for WT-64-M 1-7/8 17/32 Drill Thru for mounting clevis-centered

More information

ROUGH COUNTRY INSTRUCTION MANUAL FOR RS9500 AND RS12000 LB WINCH

ROUGH COUNTRY INSTRUCTION MANUAL FOR RS9500 AND RS12000 LB WINCH ROUGH COUNTRY INSTRUCTION MANUAL FOR RS9500 AND RS12000 LB WINCH ROUGH COUNTRY, INC 2051 EAST COURT STREET DYERSBURG, TENNESSEE 38024 PH# 1-800-222-7023 SAFETY PRECAUTIONS Warning! Observe safety precautions

More information

Technical specification for NDC 40 NO Rescue Boat Davit

Technical specification for NDC 40 NO Rescue Boat Davit Technical specification for NDC 40 NO Rescue Boat Davit 8.06.203 Re issued for construction PGO GNI GNI 0 25.04.203 Issued for construction PGO GNI GNI REV.: DATE: Reason for Issue / Description: Project

More information

Individual Winch Drive Systems from a Single Source

Individual Winch Drive Systems from a Single Source Individual Winch Drive Systems from a Single Source 2 Winch systems with Rexroth Hydraulics Winch systems with Rexroth Hydraulics 3 Need Reliable Drive Systems for Your Winch? We Deliver Them. Conditions

More information

ATV / UTV Winch. Owner s Manual

ATV / UTV Winch. Owner s Manual ATV / UTV Winch Owner s Manual OUT IN Housing Houses the series wound V DC motor which drives the gear system and ultimately driving the drum. Key Winch Components Part numbers : W35B and WS35B Freespool

More information

T24C1 T24C m 3 Chemical & Product Tanker

T24C1 T24C m 3 Chemical & Product Tanker 20 000 m 3 Chemical & Product Tanker Brief description 20 000 m 3 Chemical & Product Tanker GENERAL The FKAB is a 20 000 m 3, TIER III oil product tanker for chemicals (IMO II and III) and oil products.

More information

INSTRUCTIONS FOR: SELF RECOVERY WINCH 2720kg, 4300kg, 5400kg LINE PULL 12V MODEL No's: SRW2720(KG), SRW4300(KG), SRW5450(KG)

INSTRUCTIONS FOR: SELF RECOVERY WINCH 2720kg, 4300kg, 5400kg LINE PULL 12V MODEL No's: SRW2720(KG), SRW4300(KG), SRW5450(KG) INSTRUCTIONS FOR: SELF RECOVERY WINCH 2720kg, 4300kg, 5400kg LINE PULL 12V MODEL No's: SRW2720(KG), SRW4300(KG), SRW5450(KG) Thank you for purchasing a Sealey product. Manufactured to a high standard this

More information

Hydraulic Winch Assembly Instructions

Hydraulic Winch Assembly Instructions Page 1 of 7 Hydraulic Winch Assembly Instructions Introduction These instructions will assist you in assembling the hydraulic winch components. The winch package contains the following items that need

More information

OFF-ROAD JACK SKU: HCRG-JACK48

OFF-ROAD JACK SKU: HCRG-JACK48 OFF-ROAD JACK SKU: HCRG-JACK48 SPECIFICATIONS...2 IMPORTANT SAFETY INFORMATION...3 UNPACKING AND ASSEMBLING JACK...3 Unpacking Carton...3 Testing Operation...3 OPERATING JACK...4 Preparing Work Area...4

More information

12V ELECTRIC WINCH 9000-LB. CAPACITY OWNER S MANUAL

12V ELECTRIC WINCH 9000-LB. CAPACITY OWNER S MANUAL 12V ELECTRIC WINCH 9000-LB. CAPACITY OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result

More information

Electric winch. 4x4 & Recovery. Installation and operator s manual. Model 13500lb. recovery electric winch

Electric winch. 4x4 & Recovery. Installation and operator s manual. Model 13500lb. recovery electric winch - 1 - Electric winch 4x4 & Recovery Model 13500lb Installation and operator s manual - 1 - SAFETY PRECAUTIONS Vehicle - 2 - Warning! Observe safety precautions for personal safety and the safety of others.

More information

FULLY HYDRAULIC TRUCK CRANE

FULLY HYDRAULIC TRUCK CRANE CRANE Description Model Specification Maximum rated lifting capacity length Fly jib length Maximum lifting height Main Hoisting line winch speed Auxiliary winch Main Hoisting winch speed Auxiliary winch

More information

Owner s Manual / Fitting Instructions Kit Nos & 8515 ELECTRICALLY POWERED HUSKY WINCH

Owner s Manual / Fitting Instructions Kit Nos & 8515 ELECTRICALLY POWERED HUSKY WINCH Owner s Manual / Fitting Instructions Kit Nos. 8514 & 8515 ELECTRICALLY POWERED HUSKY WINCH Owner s Manual / Fitting Instructions Kit Nos. 8514 & 8515 These instructions cover kits from 16/07/1997 i 01

More information

WINCH lb. OWNER S MANUAL & OPERATING INSTRUCTIONS. SAVE THESE INSTRUCTIONS Important Safety Instructions are included in this manual.

WINCH lb. OWNER S MANUAL & OPERATING INSTRUCTIONS. SAVE THESE INSTRUCTIONS Important Safety Instructions are included in this manual. OWNER S MANUAL & OPERATING INSTRUCTIONS 4500 lb. WINCH MODEL NUMBER 405 SAVE THESE INSTRUCTIONS Important Safety Instructions are included in this manual. MADE IN CHINA REV 405-206079 2039 Smith Ave. Santa

More information

Eco-friendly, efficient and safe eaht winch series electric anchor handling/towing solutions

Eco-friendly, efficient and safe eaht winch series electric anchor handling/towing solutions Eco-friendly, efficient and safe eaht winch series electric anchor handling/towing solutions eaht series winches Innovations that improve performance and protect the environment Fast, clean and precise

More information

Technical specification for NDA 40 NO Rescue Boat Davit

Technical specification for NDA 40 NO Rescue Boat Davit Technical specification for NDA 40 NO Rescue Boat Davit 1.06.014 Weight information added PGO ESO GNI 1 18.06.013 Re issued for construction PGO GNI GNI 0 Issued for construction PGO GNI GNI REV.: DATE:

More information

SUREPOWR TM SERIES -SURE 49 FIELD INSTALLATION INSTRUCTIONS

SUREPOWR TM SERIES -SURE 49 FIELD INSTALLATION INSTRUCTIONS SUREPOWR TM SERIES -SURE 49 FIELD INSTALLATION INSTRUCTIONS Safety First In the maintenance and operation of mechanical equipment, SAFETY is the basic factor which must be considered at all times. Through

More information

Electric Winch Installation & Operation Manual Permanent Magnet 12 V DC EMD2000SS STAINLESS STEEL WINCH

Electric Winch Installation & Operation Manual Permanent Magnet 12 V DC EMD2000SS STAINLESS STEEL WINCH Endurance Marine Products Ltd 210 19138 26 Ave Surrey, BC V3S 3V7 T 604 535 0669 TOLL FREE 1 877 535 0669 Info@endurance-marine.com www.endurance-marine.com Electric Winch Installation & Operation Manual

More information

TASMAN SERIES DRUM WINCH

TASMAN SERIES DRUM WINCH TASMAN SERIES DRUM WINCH Copyright: VETUS-Maxwell APAC Ltd. All rights reserved VETUS-Maxwell APAC Ltd. reserves the right to make engineering changes to all products without notice. Illustrations and

More information

Rugged Ridge XHD Bumper Base with Standard Ends and a 10,500LB Winch A FEW WORDS ABOUT PRODUCT SAFETY

Rugged Ridge XHD Bumper Base with Standard Ends and a 10,500LB Winch A FEW WORDS ABOUT PRODUCT SAFETY A FEW WORDS ABOUT PRODUCT SAFETY VEHICLE RECOVERY ELECTRIC WINCH USE & INSTALLATION INSTRUCTIONS Your Rugged Ridge vehicle recovery winch is a powerful tool adding considerable utility and enjoyment to

More information

WINCH lb. C30145 Rev C

WINCH lb. C30145 Rev C C30145 Rev C30145-20081021 10006 Santa Fe Springs Road Santa Fe Springs, CA 90670 USA Made in China Owner s Manual and Operating Instructions 3000 lb. WINCH Table of Contents Introduction... 1 Accessories...

More information