VEHICLE UNDERCARRIAGE AND LIGHT ADAPTER SELECTION GUIDE
|
|
- Roy Peters
- 6 years ago
- Views:
Transcription
1 VEHILE UNDERRRIGE ND LIGHT DPTER SELETION GUIDE /21/04
2 OUT THE SELETION GUIDE The lizzard Snowplows Vehicle Undercarriage & Light dapter Selection Guide is a complete record of available undercarriage mounts and light adapters for use with lizzard snowplows. dditional undercarriage mounts and headlight adapters are continually being developed and will be added to this selection guide as they become available. LIZZRD ORPORTION RESERVES THE RIGHT, UNDER ITS ONTINUOUS IMPROVEMENT POLIY, TO HNGE ONSTRUTION OR DESIGN DETILS ND FURNISH EQUIPMENT WHEN SO LTERED WITHOUT REFERENE TO ILLUSTRTIONS OR SPEIFITIONS. This guide provides recommended snowplow model applications for specific identified vehicle models. The use of this information by an authorized lizzard dealer, or any person referencing or using this guide, for use in the process of a lizzard snowplow installation, is solely the responsibility of that person or persons. lizzard orporation does not assume liability for damage to the purchaser s vehicle resulting from the attachment and use of a lizzard snowplow. Vehicle risk is the sole responsibility of the purchaser. For additional information, review the Limited onsumer and ommercial Warranty documents at the back of this guide. These documents contain information regarding the term of warranty, warranty remedy, customer responsibility and warranty limitations for lizzard Power Plow snowplows and lizzard straight blade snowplows. SFETY Review the Safety Precautions & Snowplow Undercarriage Installation Recommendations prior to performing an installation. VEHILE UNDERRRIGE MOUNTS ll truck-mounted lizzard snowplows require a vehicle undercarriage mount to properly attach the snowplow to the vehicle. ll available undercarriages (at the time of publication of this guide) can be referenced on the following pages. TLE OF ONTENTS Safety... 3 GM Selection Guide... 4 GM Light dapter Guide... 5 Ford Selection Guide... 6 Ford Light dapter Guide... 7 Dodge Selection Guide... 8 Dodge Light dapter Guide... 9 Misc. Selection Guide Misc. Light dapter Guide Installation instructions for Light dapters onnector/dapter ross Ref Vehicle Undercarriage Modification Notice Warranty In the event a lizzard snowplow undercarriage mount does not fit, or requires modifications for proper installation (for a vehicle specified in the selection guide), complete the Vehicle Undercarriage Modification Notice form. Fax the document to lizzard Engineering at or mail the document to: lizzard orporation ttn: lizzard Engineering 95 irpark oulevard alumet, MI LIGHT DPTERS Review the Light dapters to familiarize yourself with the construction of each lizzard snowplow light adapter. The adapters are used to connect the vehicle headlights and original vehicle electrical harness to the main lighting harness on the snowplow vehicle electrical harness. Note: Due to the differences in the construction of the headlight adapters, and the various make and model vehicles lizzard snowplows can be installed on, light adapters are not included with the purchase of (or packaged with)a truck-mounted lizzard snowplow. NOTE: The 64# on the lower left corner of the front cover is the part number for this manual. The letter in the box indicates the revision level. 2 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
3 SFETY PREUTIONS ND SNOWPLOW UNDERRRIGE INSTLLTION REOMMENDTIONS WRNING: lways perform vehicle undercarriage installations with the keys removed from the vehicle s ignition. Properly tag the ignition switch to alert others work is being performed on the vehicle. WRNING: LWYS attach a DO NOT OPERTE tag to the ignition switch and/or steering wheel in the cab of the vehicle to alert others that service or maintenance is being performed. If necessary, place additional warning tags around the vehicle. Serious injury or death could occur if the engine is started and the vehicle and/or snowplow are moved while performing service or maintenance. WRNING: Most newer trucks are equipped with driver and passenger s side air bags. DO NOT remove, disable, or reposition any sensory equipment related to the safe operation of the air bags. WRNING: Vehicles equipped with air bags are designed to be activated in a frontal collision equivalent to hitting a solid object or barrier at approximately 14 mph or more. areless or high speed driving while plowing snow, which results in vehicle impact deceleration equivalent to or greater than the airbag deployment threshold described above, would deploy the airbag. Review your vehicle Owner s Manual for specific information regarding airbag deployment. WRNING: LWYS follow the vehicle manufacturer s recommendations for installing snowplowing equipment. UTION: lways follow the maintenance guidelines in a timely manner. Failure to observe maintenance guidelines may result in poor snowplow operation, increased component wear or possibly lead to part failure. Note: Vehicles equipped with lizzard Snowplows are recommended to be equipped with the vehicle manufacturer s recommended snowplow options (i.e. Snowplow prep packages). Note: The installation, modification or addition of accessories to lizzard snowplow undercarriage mounts and/or snowplows must be in compliance with published lizzard snowplow recommendations and instructions. Note: For some snowplow applications, it may be necessary to use a form of load boosting device to accommodate a snowplow installation. The use of suspension airbags, booster springs, Timbren kits or other similar load boosting devices is the responsibility of the snowplow purchaser. The selection, installation and purchase of load boosting devices is also the responsibility of the purchaser. 10-1/2" (680LT & 720LT Only) 12-1/2" (ll Other Plow Models) The recommended push beam height for the 680LT & 720LT undercarriage assembly is 10-1/2" from the center of the push beam to level ground. The recommended push beam height for all other truck-mounted snowplow models is 12-1/2". DO NOT exceed 12-1/2" (680LT & 720LT Only) or 14-1/2" (ll other models) in height for these undercarriage assemblies. UTION: If your vehicle is equipped with oversize tires, they may come into contact with the undercarriage hanger plates when turning the vehicle. The problem may be resolved by setting the steering stops on the vehicle. If this does not correct the problem, the original tires will need to be installed on the vehicle. Note: For some snowplow applications, it may be necessary to use a form of ballast to provide increased vehicle traction or maximum braking and handling. The use of ballast, such as sand bags, etc., is the responsibility of the snowplow purchaser. The selection, installation and purchase of ballast devices is also the responsibility of the purchaser. Note: For proper undercarriage installation, the vehicle must be parked on a level surface. Note: The recommended push beam height for Models 680LT and 720LT lizzard straight blade snowplows is 10-1/2" from the center of the push beam to level ground. DO NOT exceed 12-1/2" in height for this push beam installation. Review the diagram to the right. Note: The recommended push beam height for lizzard snowplow models 760LT, 760, 800, and 8611 is 12-1/2" from the center of the push beam to level ground. DO NOT exceed 14-1/2" in height for these push beam installations. Review the diagram to the right. Note: Routinely inspect all undercarriage mount hardware for tightness. Review the recommended maximum bolt torque chart in your lizzard snowplow Operation & ssembly manual. Note: Routinely clean and lubricate all electrical plugs, headlight connections, ground and battery cables, solenoid connections and switch connections to prevent corrosion. pply dielectric grease for every 25 hours of snowplow use.you may need to grease more frequently depending on your plowing environment. Note: Follow all maintenance guidelines indicated in your lizzard snowplow Operation & ssembly manual. Note: Follow all safety and warning labels indicated on the snowplow and/or in your lizzard snowplow Operation & ssembly manual. Vehicle Undercarriage and Light dapter Selector Guide Pub. No
4 GM SELETION GUIDE VEHILE MODEL PPLITION LIZZRD SNOWPLOW MODEL PPLITION MOUNT PN 680LT 720LT 760LT OLORDO/NYON SONOM S10 LZER/JIMMY S10 PIKUP S15 JIMMY S15 PIKUP 04 ENVOY TRILLZER LZER/JIMMY OLDS RVD S10 PIKUP/SONOM LZER ZR2/JIMMY ZR S10 ZR2/SONOM ZR K1500 YUKON K1500 THOE K1500 SUURN K1500 LZER K1500 PIKUP K1500 VLNHE K1500 THOE/YUKON/YUKON L K1500 SUURN K1500 SILVERDO/SIERR K1500 SILVERDO/SIERR W/ 3" LIFT K1500 LZER/JIMMY K10/K1500 SUURN K10/K1500 PIKUP K2500 VLNHE K1500 HD SILVERDO/SIERR K3500 PIKUP K2500 SUURN/YUKON L K2500 SILVERDO/SIERR K2500 SUURN K2500 PIKUP K3500 PIKUP K20/K2500 SUURN K20/K2500 PIKUP K30/K3500 PIKUP HEV HD HSS. (2WD) GM 3500 HD HSS (2WD) /5500 (2WD) Vehicle Undercarriage and Light dapter Selector Guide Pub. No
5 GM LIGHT DPTER GUIDE VEHILE MODEL PPLITION HEDLIGHT DPTER PPLITION OLORDO/NYON 04 TRILLZER/ENVOY TRILLZER S10 PIKUP/LZER/JIMMY/SONOM OLDS RVD OLDS RVD S10 PIKUP/LZER S15- JIMMY/PIKUP/SONOM 03 K1500 HD SILVERDO/SIERR K1500 HD SILVERDO/SIERR K1500 SILVERDO/SIERR K1500 SILVERDO/SIERR 03 K1500 VLNHE/YUKON L 02 K1500 VLNHE 03 K1500 THOE/YUKON K1500 THOE/YUKON/YUKON L K1500 THOE K1500 YUKON 03 K1500 SUURN K1500 SUURN K1500 SUURN K10/K1500 SUURN K1500 LZER K1500 PIKUP K1500 LZER/JIMMY K10/K1500 PIKUP K2500 SILVERDO/SIERR K2500 SILVERDO/SIERR 03 K2500 VLNHE/YUKON L 02 K2500 VLNHE K2500 YUKON L 03 K2500 SUURN K2500 SUURN K2500 SUURN K20/K2500 SUURN K2500/K3500 PIKUP K20/K2500 K30/K3500 PIKUP 03 K3500 PIKUP K3500 PIKUP HEV.3500 HD HSS GM 3500 HD HSS /5500 Note: Some vehicle applications may have more than one headlight adapter identified. If so, please review adapter diagrams to help determine which adapter is needed. Vehicle Undercarriage and Light dapter Selector Guide Pub. No
6 FORD SELETION GUIDE VEHILE MODEL PPLITION LIZZRD MOUNT PN SNOWPLOW MODEL PPLITION 680LT 720LT 760LT EPLORER SPORT TR MOUNTINEER MZD 3000/4000 PIKUP EPLORER RNGER PIKUP RONO II EPLORER F-150 F4 PIKUP EPEDITION F-150 PIKUP F-150 PIKUP RONO F-150 PIKUP RONO F-150 PIKUP EPEDITION F-250 HD PIKUP F-350 PIKUP F-250/F-350 PIKUP EURSION F-250/F-350/F-450/F SUPER DUTY PIKUP F-650 SD OMMERIL F-650 SD OMMERIL F-250/F-350/F-450/F-550 SUPER DUTY PIKUP Vehicle Undercarriage and Light dapter Selector Guide Pub. No
7 FORD LIGHT DPTER GUIDE VEHILE MODEL PPLITION HEDLIGHT DPTER PPLITION EPLORER SPORT TR 04 RNGER PIKUP RNGER PIKUP EPLORER EPLORER 02 MERURY MOUNTINEER MERURY MOUNTINEER RONO II / F-150 F4 PIKUP 04 F-150 PIKUP F-150 PIKUP F-150 PIKUP EPEDITION 04 EPEDITION RONO RONO EURSION F-250 SUPER DUTY F-250 HD PIKUP F-250 PIKUP F-350 PIKUP F-350 PIKUP F-350 PIKUP F-450/F-550 SUPER DUTY PIKUP F-650 SD OMMERIL F-650 SD OMMERIL 05 F-250/F-350/F-450/F-550 SUPER Note: Some vehicle applications may have more than one headlight adapter identified. If so, please review adapter diagrams to help determine which adapter is needed. Vehicle Undercarriage and Light dapter Selector Guide Pub. No
8 DODGE SELETION GUIDE VEHILE MODEL PPLITION LIZZRD MOUNT PN SNOWPLOW MODEL PPLITION 680LT 720LT 760LT DURNGO SLT DKOT SPORT PIKUP DKOT SLT ET DKOT PIKUP DURNGO DKOT PIKUP DURNGO RM PIKUP RM PIKUP SPORT RM PIKUP RM PIKUP /3500 RM PIKUP/SPORT W200/W250 PIKUP W300/W350 PIKUP LIERTY WRNGLER TJ OMNHE MJ HEROKEE J WGONEER LTD WRNGLER YJ Vehicle Undercarriage and Light dapter Selector Guide Pub. No
9 DODGE LIGHT DPTER GUIDE VEHILE MODEL PPLITION HEDLIGHT DPTER PPLITION DURNGO DURNGO/DURNGO SLT DKOT SLT ET /PIKUP DKOT SPORT PIKUP DKOT PIKUP RM PIKUP RM PIKUP RM SPORT RM PIKUP RM SPORT RM PIKUP W200/W250 PIKUP RM PIKUP RM SPORT RM PIKUP W300/W350 PIKUP 04 LIERTY WRNGLER TJ WRNGLER YJ HEROKEE J WGONEER WGONEER LTD OMNHE MJ Note: Some vehicle applications may have more than one headlight adapter identified. If so, please review adapter diagrams to help determine which adapter is needed. Vehicle Undercarriage and Light dapter Selector Guide Pub. No
10 MIS. SELETION GUIDE VEHILE MODEL PPLITION LIZZRD SNOWPLOW MODEL PPLITION MOUNT PN 680LT 720LT 760LT FL 40/50/60/ MITSUISHI FUSO FG NISSN FRONTIER NISSN PIKUP TOYOT TOM TOYOT TUNDR NISSN TITN Vehicle Undercarriage and Light dapter Selector Guide Pub. No
11 MIS. LIGHT DPTER GUIDE VEHILE MODEL PPLITION HEDLIGHT DPTER PPLITION FL 40/50/60/70 03 MITSUISHI FUSO FG NISSN FRONTIER NISSN FRONTIER NISSN PIKUP TOYOT TOM TOYOT TUNDR 04 NISSN TITN Note: Some vehicle applications may have more than one headlight adapter identified. If so, please review adapter diagrams to help determine which adapter is needed. Vehicle Undercarriage and Light dapter Selector Guide Pub. No
12 GENERL INSTLLTION INSTRUTIONS FOR LL HEDLIGHT DPTERS 1 Prior to installing the headlight adapters, verify the original vehicle equipment is in proper working order. Test the vehicle headlights (high and low beam), turn signals and run lights.verify fog lamps or other optional lighting equipment is also in good working order if so equipped. 2 Remove the existing vehicle headlight connector from the headlight. 3 Plug the headlight adapter into the vehicle headlight receptacle. Note: If more than one plug is present, match the colors of each connector (gray to gray, black to black, hevrolet daylight running: clear to gray, etc.). 4 onnect the existing vehicle headlight connector into the headlight adapter. 5 Plug the black (or gray depending on headlight adapter construction), 5-pin connector on the headlight adapter into the 5-pin connector on the vehicle wire harness. 6 Verify the vehicle and plow headlights are in proper working condition, including the turn lights. djust the plow headlight beams as needed. 12 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
13 ONNETOR/DPTER ROSS REFERENE DPTER PN ONNETOR PN DESRIPTION HEDLIGHT PN H2, H4, 2/2D DUL RETNGULR OR DUL ROUND 9003, 6014/H6014, H6017, 6052, H6024, H6059, H6054/HP6054, H H1 DUL RETNGULR OMPOSITE HLOGEN 9004/H H5 DUL RETNGULR OMPOSITE HLOGEN 9007/H H3/H4 QUD OMPOSITE HLOGEN H9005, H H3/H4 QUD OMPOSITE HLOGEN H9005, H LF/UF QUD LOW PROFILE RETNGULR HLOGEN H4701, H H1/H5 QUD OMPOSITE HLOGEN 9004/H9004, /2 QUD RETNGULR HEDLMP 9007/H , H4651, 4652, H4652, H4656, H4662, HP H13 DUL ROUND HLOGEN H E DUL RETNGULR (SMLL) HLOGEN H4666, H6545, HP H3/H4 QUD OMPOSITE HLOGEN H9005, H H3/HID DUL ROUND HIGH INTENSITY DISHRGE LMP H9005, D1R-HID MODULE H3/H6 QUD OMPOSITE HLOGEN H9005, H H3/H7 QUD OMPOSITE HLOGEN H9005, H Note: The switch between low and high beams is one the positive (power) side of the headlight bulb. Note: The switch between low and high beams is one the negative (ground) side of the headlight bulb. Note: Headlight adapter construction may contain loose spade terminals or a molded connector. Use a test light to determine the correct connections for each terminal. Note: "" ommons; The switch between high and low beams is on the negative (ground) side of the headlight bulb. Daytime running lights are run through the high beam bulbs. Note: 62171"" ommons; The switch between high and low beams is on the negative (ground) side of the headlight bulb. Daytime running lights are run through the high beam bulbs. Vehicle Undercarriage and Light dapter Selector Guide Pub. No
14 LIGHT DPTER NUMER VEHILE MODEL PPLITION 04 OLORDO/NYON* OLDS RVD* S10 PIKUP/LZER S15-JIMMY/PIKUP/SONOM* K1500 THOE* K1500 YUKON* K1500 SUURN* K10/K1500 SUURN* K1500 LZER* K1500 PIKUP* K1500 LZER/JIMMY* K10/K1500 PIKUP* K2500 SUURN* K20/K2500 SUURN* K2500/K3500 PIKUP* K20/K2500 K30/K3500 PIKUP* HEV.3500 HD HSS. * GM 3500 HD HSS. * * / RNGER PIKUP* EPLORER* RONO II* F-150 PIKUP* RONO* EURSION* F-250 SUPER DUTY* F-250 PIKUP* F-350 PIKUP* F-350 PIKUP* 04 F-650 SD OMMERIL* F-650 SD OMMERIL* W200/W250 PIKUP W300/W350 PIKUP WRNGLER TJ WRNGLER YJ HEROKEE J WGONEER LTD OMNHE MJ FL 40/50/60/70* 03 MITSUISHI FUSO FG* NISSN FRONTIER* NISSN PIKUP* TOYOT TOM TOYOT TUNDR NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 14 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
15 VENDOR P/N & DWG: REV (REF. M.P.M ) NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H2, H4, 2/2D HEDLIGHT DESRIPTION: DUL RETNGULR OR DUL ROUND HEDLIGHT UL NUMER(S): 9003, 6014, H6014, H6017, 6052, H6024, H6059, H6054, HP6054, H-54 D E = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) END VIEW OF ONNETOR MOLD OLOR (LK) = HIGH EM (YELLOW/RED) = LOW EM (LT. GREEN/RED) = OMMON () YELLOW/RED LT. GREEN/RED LT. GREEN YELLOW 3" ± 1/2" = HIGH EM (YELLOW) = LOW EM (LT. GREEN) = OMMON () 1 1 YELLOW/RED YELLOW Y/R Y W/R-2 W/R-1 LT. GREEN/RED LT. G/R LT. G FRONT END VIEW 3" +1/2" to -1/4" FRONT END VIEW 6"+1/2" to -1-1/4" MOLD OLOR (LK)
16 LIGHT DPTER NUMER VEHILE MODEL PPLITION RNGER PIKUP* EPLORER* RONO II* F-150 PIKUP* RONO* F-250 PIKUP* F-350 PIKUP* DKOT PIKUP* RM PIKUP RM PIKUP* RM PIKUP RM PIKUP RM PIKUP NISSN FRONTIER* NISSN PIKUP* NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 16 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
17 VENDOR P/N & DWG: REV (REF. M.P.M ) NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H1 HEDLIGHT DESRIPTION: DUL RETNGULR OMPOSITE HLOGEN HEDLIGHT UL NUMER(S): 9004, H9004 D E = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) END VIEW OF ONNETOR MOLD OLOR (LK) YELLOW/RED LT. GREEN/RED LT. GREEN YELLOW = OMMON () = LOW EM (LT. GREEN/RED) = HIGH EM (YELLOW/RED) 3" ± 1/2" = OMMON () = LOW EM (LT. GREEN) = HIGH EM (YELLOW) 1 1 YELLOW/RED LT. GREEN/RED Y/R LT. G/R W/R-2 Y LT. G W/R-1 YELLOW LT. GREEN FRONT END VIEW 6" ± 1/2" MOLD OLOR (GRY) FRONT END VIEW
18 LIGHT DPTER NUMER VEHILE MODEL PPLITION EPLORER SPORT TR 04 RNGER PIKUP RNGER PIKUP* EPLORER* MERURY MOUNTINEER RONO II* / F-150 F4 PIKUP F-150 PIKUP EPEDITION RONO EURSION* F-250 SUPER DUTY* F-250 HD PIKUP F-350 PIKUP F-350 PIKUP F-450/F-550 SUPER DUTY PIKUP 04 DURNGO DURNGO/DURNGO SLT DKOT SLT ET /PIKUP RM PIKUP RM PIKUP* 04 LIERTY NISSN FRONTIER NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 18 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
19 VENDOR P/N & DWG: REV (REF M.P.M ) NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H5 HEDLIGHT DESRIPTION: DUL RETNGULR OMPOSITE HLOGEN HEDLIGHT UL NUMER(S): 9007, H9007 D E END VIEW OF ONNETOR YELLOW/RED = LOW EM (LT. GREEN/RED) = OMMON () = HIGH EM (YELLOW/RED) LT. GREEN/RED YELLOW LT. GREEN 3" + 1/2" 1 YELLOW/RED LT. GREEN/RED Y/R W/R-2 LT. G/R Y W/R-1 LT. G YELLOW LT. GREEN FRONT END VIEW 6" + 1/2" MOLD OLOR (LK) FRONT END VIEW 1 = LOW EM (LT. GREEN) = OMMON () = HIGH EM (YELLOW) MOLD OLOR (LK) = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED)
20 LIGHT DPTER NUMER VEHILE MODEL PPLITION TRILLZER* S10 PIKUP/LZER/JIMMY/SONOM* OLDS RVD* OLDS RVD* S10 PIKUP/LZER S15-JIMMY/PIKUP/SONOM* 03 K1500 HD SILVERDO/SIERR K1500 SILVERDO/SIERR 03 K1500 VLNHE/YUKON L 03 K1500 THOE/YUKON K1500 THOE* K1500 YUKON* 03 K1500 SUURN K1500 SUURN* K1500 LZER* K1500 PIKUP* K2500 SILVERDO/SIERR 03 K2500 VLNHE/YUKON L 03 K2500 SUURN K2500 SUURN* K2500/K3500 PIKUP* 03 K3500 PIKUP HEV.3500 HD HSS. * GM 3500 HD HSS. * * EPLORER 02 MERURY MOUNTINEER 04 EPEDITION Note: The switch between low and high beams is one the positive (power) side of the headlight bulb. NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 20 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
21 GRY LOW EM FRONT END VIEW LT. GREEN/RED W/R-4 LT. G/R 10"+1" to -1/2" 5"+1/2" to -1/4" LT. G LT. GREEN MOLD OLOR (GRY) FRONT END VIEW LOW EM 1 = LOW EM (LT. GREEN/RED) = OMMON () 3"+1/2" to -1/4" 1 = LOW EM (LT. GREEN) = OMMON () LK HIGH EM YELLOW/RED W/R-1 W/R-2 W/R-3 Y/R Y YELLOW HIGH EM END VIEW OF ONNETOR 2 = HIGH EM (YELLOW/RED) = OMMON () = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) 4"+1/2" to -1/4" 2 MOLD OLOR (LK) = HIGH EM (YELLOW) = OMMON () D E MOLD OLOR (LK) HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H3/H4 HEDLIGHT DESRIPTION: QUD OMPOSITE HLOGEN HEDLIGHT UL NUMER(S): H9005, H9006 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: REV (REF. M.P.M ) NOTE: THE SWITH ETWEEN LOW ND HIGH EMS IS ON THE POSITIVE (POWER) SIDE OF THE HEDLIGHT UL.
22 LIGHT DPTER NUMER VEHILE MODEL PPLITION 04 OLORDO/NYON* TRILLZER* S10 PIKUP/LZER/JIMMY/SONOM* OLDS RVD* K1500 HD SILVERDO/SIERR K1500 SILVERDO/SIERR 02 K1500 VLNHE K1500 THOE/YUKON/YUKON L K1500 SUURN K2500 SILVERDO/SIERR 02 K2500 VLNHE K2500 YUKON L K2500 SUURN K3500 PIKUP HEV.3500 HD HSS. * GM 3500 HD HSS. * * 04 NISSN TITN* Note: The switch between low and high beams is one the negative (ground) side of the headlight bulb. NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 22 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
23 10" ± 1/2" GRY LOW EM 1 LT. GREEN/RED LT. G/R W/R-4 = OMMON () = LOW EM (LT. GREEN/RED) 3" ± 1/2" LK HIGH EM YELLOW/RED Y/R W/R-2 2 END VIEW OF ONNETOR D E = OMMON () = HIGH EM (YELLOW/RED) = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) 4" ± 1/2" MOLD OLOR (LK) HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H3/H4 HEDLIGHT DESRIPTION: QUD OMPOSITE HLOGEN HEDLIGHT UL NUMER(S): H9005, H9006 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: REV (REF. M.P ) LT. G W/R-3 5" ± 1/2" LT. GREEN MOLD OLOR (LK) 1 LOW EM = OMMON () = LOW EM (LT. GREEN) Y W/R-1 YELLOW 2 HIGH EM = OMMON () = HIGH EM (YELLOW) MOLD OLOR (LK) NOTE: THE SWITH ETWEEN LOW ND HIGH EMS IS ON THE NEGTIVE (GROUND) SIDE OF THE HEDLIGHT UL.
24 LIGHT DPTER NUMER VEHILE MODEL PPLITION K1500 THOE* K1500 YUKON* K1500 SUURN* K10/K1500 SUURN* K1500 LZER* K1500 PIKUP* K1500 LZER/JIMMY* K10/K1500 PIKUP* K2500 SUURN* K20/K2500 SUURN* K2500/K3500 PIKUP* K20/K2500 K30/K3500 PIKUP* HEV.3500 HD HSS. * GM 3500 HD HSS. * * WGONEER NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 24 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
25 LOW EM FRONT END VIEW = OMMON () 1 = LOW EM (LT. GREEN/RED) PV ONNETOR MOLD OLOR (LK) FRONT END VIEW LT. GREEN/RED W/R-4 LT. G/R 10"+1" to -1/2" 3"+1/2" to -1/4" 5"+1/2" to -1/4" LT. G LT. GREEN HIGH EM END VIEW OF ONNETOR D 2 E YELLOW/RED = OMMON () = HIGH EM (YELLOW/RED) W/R-1 Y/R = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) 4"+1/2" to -1/4" W/R-3 W/R-2 Y YELLOW MOLD OLOR (LK) HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): LF/UF HEDLIGHT DESRIPTION: QUD LOW PROFILE RETNGULR HLOGEN HEDLIGHT UL NUMER(S): H4701, H4703 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: REV (REF M.P.M ) 1 2 FRONT END VIEW LOW EM = OMMON () = LOW EM (LT. GREEN) FRONT END VIEW HIGH EM = OMMON () = HIGH EM (YELLOW)
26 LIGHT DPTER NUMER VEHILE MODEL PPLITION DKOT SPORT PIKUP RM SPORT RM SPORT RM SPORT NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 26 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
27 FRONT END VIEW UL H9004 HIGH EM YELLOW/RED VITY PLUG Y/R-2 NOT USED W/R-2 2 = OMMON () = NOT USED (VITY PLUG) = HIGH EM (YELLOW/RED) 9" ± 1/4" FRONT END VIEW UL H9007 YELLOW/RED LT. GREEN/RED Y/R-1 W/R-3 LT. G/R 1 = LOW EM (LT. GREEN/RED) = OMMON () = HIGH EM (YELLOW/RED) 6"-1/2" ± 1/2" HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H1/H5 HEDLIGHT DESRIPTION: QUD OMPOSITE HLOGEN HEDLIGHT UL NUMER(S): 9004, H9004, 9007, H9007 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: REV (REF. M.P.M ) 3"-1/4" ± 1/4" Y YELLOW W/R-1 LT. G LT. GREEN 3"-1/4" ± 1/4" MOLD OLOR (LK) FRONT END VIEW 1 = LOW EM (LT. GREEN) = OMMON () = HIGH EM (YELLOW) END VIEW OF ONNETOR D E MOLD OLOR (LK) = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED)
28 LIGHT DPTER NUMER VEHILE MODEL PPLITION K10/K1500 SUURN* K1500 LZER/JIMMY* K10/K1500 PIKUP* K20/K2500 SUURN* K20/K2500 K30/K3500 PIKUP* 04 F-650 SD OMMERIL* F-650 SD OMMERIL* FL 40/50/60/70* 03 MITSUISHI FUSO FG* NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 28 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
29 VENDOR P/N & DWG: REV (REF. M.P.M ) NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): 1/2 HEDLIGHT DESRIPTION: QUD RETNGULR HEDLIGHT UL NUMER(S): 4651, H4651, 4652, H4652, H4656, H4662, HP6054 D E = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) 2 = = NOT USED = YELLOW/RED END VIEW OF ONNETOR MOLD OLOR (LK) NOT USED YELLOW/RED FRONT END VIEW YELLOW/RED YELLOW/RED LT. GREEN/RED LT. GREEN YELLOW 3" ± 1/2" 13"+1/2" to -1-1/4" 1 1 = = YELLOW/RED = LT. GREEN/RED = OMMON () = HIGH EM (YELLOW) = LOW EM (LT. GREEN) YELLOW/RED YELLOW LT. GREEN/RED LT. GREEN FRONT END VIEW 7"+1" to -1-1/4" 3"-1/2" + 1/2" to -3/4" MOLD FRONT END OLOR (LK) VIEW
30 LIGHT DPTER NUMER VEHILE MODEL PPLITION F-150 PIKUP NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 30 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
31 YELLOW/RED LT. GREEN/RED FRONT END VIEW 1 = LOW EM (LT. GREEN/RED) = OMMON () = HIGH EM (YELLOW/RED) HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H13 HEDLIGHT DESRIPTION: DUL ROUND HLOGEN HEDLIGHT UL NUMER(S): H9008 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: REV (REF. M.P.M ) LT. GREEN/RED YELLOW/RED LT. G/R W/R-2 Y/R 6" ± 1/2" YELLOW LT. GREEN Y W/R-1 LT. G YELLOW LT. GREEN FRONT END VIEW 3" ± 1/2" 1 = LOW EM (LT. GREEN) = OMMON () = HIGH EM (YELLOW) END VIEW OF ONNETOR MOLD OLOR (LK) D E = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED)
32 LIGHT DPTER NUMER VEHILE MODEL PPLITION OLDS RVD* S10 PIKUP/LZER S15-JIMMY/PIKUP/SONOM* DKOT PIKUP* Note: Headlight adapter construction may contain loose spade terminals or a molded connector. Use a test light to determine the correct connections for each terminal. NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 32 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
33 FRONT END VIEW HI 1 = OMMON () = HIGH EM (YELLOW/RED) = LOW EM (LT. GREEN/RED) OM LOW 3"-1/2" + 1" to -1/2" 3"-1/2" + 1" to -1/2" LT. GREEN/RED LT. GREEN YELLOW/RED YELLOW 3"-1/2" + 1" to -1/2" END VIEW OF ONNETOR D E HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): 2E HEDLIGHT DESRIPTION: DUL RETNGULR (SMLL) HLOGEN HEDLIGHT UL NUMER(S): H4666, H6545, HP6545 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: REV (REF. M.P.M ) LOW EM (LT. GREEN) HIGH EM (YELLOW) OMMON () MOLD OLOR (LK) = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED)
34 LIGHT DPTER NUMER VEHILE MODEL PPLITION S10 PIKUP/LZER/JIMMY/SONOM* OLDS RVD* Note: "" ommons; The switch between high and low beams is on the negative (ground) side of the headlight bulb. Daytime running lights are run through the high beam bulbs. NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 34 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
35 FRONT END VIEW 10"±1/2" GRY LOW EM 1 LT. GREEN/RED = OMMON () = LOW EM (LT. GREEN/RED) 3"±1/2" LK HIGH EM 2 END VIEW OF ONNETOR YELLOW/RED 19-1/2"±1/2" TO LLOW FOR ONNETOR SEPERTION. = OMMON () = HIGH EM (YELLOW/RED) 4"±1/2" E D HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H3/H4 HEDLIGHT DESRIPTION: QUD OMPOSITE HLOGEN LMP HEDLIGHT UL NUMER(S): H9005, H9006 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: (REF. M.P.M REV ) 5"±1/2" LT. GREEN 1 MOLD OLOR (RED) = OMMON () = LOW EM (LT. GREEN/RED) FRONT END VIEW LOW EM MOLD OLOR (LK) FRONT END VIEW YELLOW 2 = OMMON () = HIGH EM (YELLOW) HIGH EM MOLD OLOR (LK) = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) OMMONS NOTE: THE SWITH ETWEEN LOW ND HIGH EMS IS ON THE NEGTIVE (GROUND) SIDE OF THE HEDLIGHT UL. DYTIME RUNNING LIGHTS RE THROUGH THE HIGH EM ULS.
36 LIGHT DPTER NUMER VEHILE MODEL PPLITION DILL ESLDE NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 36 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
37 HID MODULE FRONT END VIEW H9005 HIGH EM LK = OMMON () 2 = TTERY POS + (ORNGE) 3 = LOW EM (LT. GREEN/RED) NOTE: GM DO I.D.# IS INORRET = HIGH EM (YELLOW/RED) = OMMON () END VIEW OF ONNETOR D E LT. GREEN/RED 10"+ 1" to -1/2" ORNGE (ORNGE WIRE IS 20" LONG, TO LLOW ONNETOR SEPERTION) YELLOW/RED 3"+ 1/2" to -1/4" 4"+ 1/2" to -1/4" 5"+ 1/2" to -1/4" LT. GREEN/RED ORNGE 1 YELLOW 2 MOLD OLOR (LK) = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) = OMMON () 2 = TTERY POS + (ORNGE) 3 = LOW EM (LT. GREEN/RED) NOTE: GM DO I.D.# IS INORRET = HIGH EM (YELLOW) = OMMON () FRONT END VIEW HIGH EM LK HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H3/HID HEDLIGHT DESRIPTION: DUL ROUND HIGH INTENSITY DISHRGE (HID) LMP HEDLIGHT UL NUMER(S): H9005 (HIGH EM), D1R-HID MODULE (LOW EM) NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: (REF. M.P.M )
38 LIGHT DPTER NUMER VEHILE MODEL PPLITION OLDS RVD* Note: 62171"" ommons; The switch between high and low beams is on the negative (ground) side of the headlight bulb. Daytime running lights are run through the high beam bulbs. NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 38 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
39 10"±1/2" GRY LOW EM 1 LT. GREEN/RED = LOW EM (LT. GREEN/RED) = OMMON () 3"±1/2" LK HIGH EM 19-1/2"±1/2" TO LLOW FOR ONNETOR SEPERTION. YELLOW/RED 2 END VIEW OF ONNETOR = HIGH EM (YELLOW/RED) = OMMON () 4"±1/2" E D HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H3/H4 HEDLIGHT DESRIPTION: QUD OMPOSITE HLOGEN LMP HEDLIGHT UL NUMER(S): H9005, H9006 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES VENDOR P/N & DWG: (REF. M.P.M REV ) 10"±1/2" LT. GREEN 1 MOLD OLOR (ORNGE) = LOW EM (LT. GREEN) = OMMON () LOW EM YELLOW 2 = HIGH EM (YELLOW) = OMMON () LK HIGH EM MOLD OLOR (LK) = OMMON () = HIGH EM FEED (YELLOW) = LOW EM FEED (LT. GREEN) D = HIGH EM (YELLOW/RED) E = LOW EM (LT. GREEN/RED) OMMONS NOTE: THE SWITH ETWEEN LOW ND HIGH EMS IS ON THE NEGTIVE (GROUND) SIDE OF THE HEDLIGHT UL. DYTIME RUNNING LIGHTS RE THROUGH THE HIGH EM ULS.
40 LIGHT DPTER NUMER VEHILE MODEL PPLITION TRILLZER/ENVOY NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required. 40 Vehicle Undercarriage and Light dapter Selector Guide Pub. No
41 D = YEL = LT GREEN = WHT/RED D= WHT/RED D E D = YEL/RED = GRN/RED = WHT/RED D= WHT/RED 9" (2 PLES) TERMINL INSERTION VIEW = WHT/RED (OMMON) = YEL (HIGH EM FEED) = LT GRN (LOW EM FEED) D= YEL/RED (HIGH EM) E= GRN/RED (LOW EM) HEDLIGHT DPTER P/N HEDLIGHT ONNETOR(S): H3/H4 HEDLIGHT DESRIPTION: QUD OMPOSITE HLOGEN HEDLIGHT UL NUMER(S): H9005, H9006 NOT DRWN TO SLE UNLESS OTHERWISE SPEIFIED LL DIMENSIONS IN INHES WIRE - 16 G GPT LL ONNETORS VIEWED FROM WIRE END EEPT WHERE NOTED VENDOR P/N & DWG: P-5607-FG REV (REF. P DWG# P-5607-FG-DWG)
42 LIGHT DPTER NUMER VEHILE MODEL PPLITION NISSN TITN* NOTE: If vehicle model application is marked with an asterisk (*) then more than one light adapter may be specified. See light adapter diagrams and connector/adapter cross reference pages to determine which adapter is required.
43 NOTES USTOMER NME: VEHILE UNDERRRIGE MODIFITION NOTIE DELER: USTOMER DDRESS: STTE: ZIP: USTOMER TELEPHONE: ( ) VIN: MKE: FORD HEV GM DODGE TOYOT OTHER: MODEL: (Ex. Silverado K2500 HD Pickup) YER: DTE OF MNUFTURE: DRIVE TRIN: 2WD 4WD LL WHEEL OTHER: DRW (DUL RER WHEELS) YES NO ODY STYLE: REG - OTHER: O OPTION(S): DUMP O STKE ED OTHER: ENGINE TYPE: GS DIESEL ENGINE SIZE: (Example: 6.0L V8) GFWR: L KG GRWR: L KG GVWR: L KG HEDLMP NUMER(S): DYTIME RUNNING LIGHTS: YES NO HEDLMP ONNETOR: (Ex. H3/H4, 1/2, LF/UF, etc.) LIZZRD DPTER KIT: OTHER: MODIFY UMPER: YES NO UMPER MOD IF. MDE: U.. MOUNT INSTLLED: MODIFY U.. MOUNT: U.. MODIFITION MDE: P/N: YES NO (IF YES: F OR MIL TO LIZZRD ENGINEERING -DOUMENT HNGE ELOW) MIL TO: LIZZRD ORP. 95 IRPRK LVD. LUMET, MI F TO: LIZZRD INSTLLER: DTE OF INSTLL: PLOW MODEL INSTLLED: 680LT 720LT 760LT OTHER: REV 03-04/04
44 LIZZRD POWER PLOW LIMITED ONSUMER WRRNTY This warranty covers defects in material and workmanship except as set forth below. WRRNTED PRTY: This warranty applies only to the Original Purchaser who purchased this plow from an uthorized lizzard Dealer, for personal, family or household use. TERM OF WRRNTY: This lizzard Power Plow snowplow is warranted for the following period: Parts and labor are warranted for one year from date of purchase. LIZZRD ORPORTION S WRRNTY REMEDY: lizzard orporation will, at its sole discretion, repair or replace defective parts at no charge. USTOMERS RESPONSIILITY: To obtain warranty service, the purchaser must return the defective snowplow to any uthorized lizzard Dealer. The purchaser must verify the original purchase date. Transportation costs to and from the dealer will be the responsibility of the purchaser. ITEMS NOT OVERED UNDER THIS WRRNTY: This limited warranty does not cover the following: 1. Expendable parts such as cutting edges, plow shoes, hoses, fasteners, blade guides, paint finish, etc. 2. ny snowplow or part thereof which has been repaired or altered by anyone other than an uthorized lizzard Dealer. 3. ny snowplow or part thereof which has been subject to neglect, misuse, accident, improper installation, maintenance, or storage. This includes, but is not limited to, corrosion of any electrical components. 4. Snowplows mounted on vehicles other than those for whom lizzard orporation has provided a specific undercarriage system. 5. lizzard orporation does not assume liability for damage to the purchaser's vehicle resulting from the attachment and use of a lizzard Power Plow snowplow. Vehicle risk is the sole responsibility of the purchaser. WRRNTY LIMITTIONS: THIS WRRNTY IS OFFERED IN LIEU OF NY OTHER EPRESS WRRNTY. THE DURTION OF LL IMPLIED WRRNTIES, INLUDING UT NOT LIMITED TO THE IMPLIED WRRNTIES OF MERHNTILITY ND FITNESS FOR PRTIULR PURPOSE, RE LIMITED TO THE DURTION OF THIS WRRNTY. LIZZRD ORPORTION'S LIILITY IS EPRESSLY LIMITED TO REPIR OR REPLEMENT OF DEFETIVE PRTS. LIZZRD ORPORTION SHLL NOT E LILE FOR ONSEQUENTIL, INIDENTL OR ONTINGENT DMGES WHTSOEVER, EVEN IF DMGES RE USED Y THE NEGLIGENE OR FULT OF LIZZRD ORPORTION. State Laws: Some states do not allow exclusion of incidental or consequential damages or the limitations on how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. This warranty does not apply if you purchased your snowplow for other than personal, family, or household use. If purchased for other than personal, family or household use, refer to the lizzard Power Plow ommercial Warranty. 95 IRPRK OULEVRD LUMET, MIHIGN [906] REV 8/01
45 OMMERIL WRRNTY This warranty covers defects in material and workmanship except as set forth below. WRRNTED PRTY: This warranty applies only to the Original Purchaser who purchased this plow from an uthorized lizzard Dealer, for commercial use. TERM OF WRRNTY: This lizzard Power Plow snowplow is warranted for the following period: Parts and labor are warranted for one year from date of purchase. LIZZRD ORPORTION S WRRNTY REMEDY: lizzard orporation will, at its sole discretion, repair or replace defective parts at no charge. USTOMERS RESPONSIILITY: To obtain warranty service, the purchaser must return the defective snowplow to any uthorized lizzard Dealer within the warranty period. The purchaser must verify the original purchase date. Transportation costs to and from the Dealer will be the responsibility of the purchaser. ITEMS NOT OVERED UNDER THIS WRRNTY: This warranty does not cover the following: LIZZRD POWER PLOW 1. Expendable parts such as cutting edges, plow shoes, hoses, fasteners, blade guides, paint finish, etc. 2. ny snowplow or part thereof which has been repaired or altered by anyone other than an uthorized lizzard Dealer. 3. ny snowplow or part thereof which has been subject to neglect, misuse, accident, improper installation, maintenance, or storage. This includes, but is not limited to, corrosion of any electrical components. 4. Snowplows mounted on vehicles other than those for whom lizzard orporation has provided a specific undercarriage system. 5. lizzard orporation does not assume liability for damage to the purchaser's vehicle resulting from the attachment and use of a lizzard Power Plow snowplow. Vehicle risk is the sole responsibility of the purchaser. LIMITS OF LIZZRD ORPORTION S LIILITIES: LIZZRD ORPORTION'S LIILITY IS EPRESSLY LIMITED TO REPIR OR REPLEMENT OF DEFETIVE PRTS. LIZZRD ORPORTION SHLL NOT E LILE FOR ONSEQUENTIL, INIDENTL OR ONTINGENT DMGES WHTSOEVER, EVEN IF DMGES RE USED Y THE NEGLIGENE OR FULT OF LIZZRD ORPORTION. THE FOREGOING WRRNTIES RE ELUSIVE ND IN LIEU OF LL OTHER EPRESSED ND IMPLIED WRRNTIES INLUDING, UT NOT LIMITED TO, THE IMPLIED WRRNTIES OF MERHNTILITY ND FITNESS FOR PRTIULR PURPOSE. This warranty does not apply if you purchased your snowplow for personal, family, or household use. In this case, refer to the lizzard Power Plow Limited onsumer Warranty. 95 IRPRK OULEVRD LUMET, MIHIGN [906] REV 8/01
46 LIZZRD LIMITED ONSUMER WRRNTY This warranty covers defects in material and workmanship except as set forth below. WRRNTED PRTY: This warranty applies only to the Original Purchaser who purchased this plow from an uthorized lizzard Dealer, for personal, family or household use. TERM OF WRRNTY: This lizzard straight blade snowplow is warranted for the following period: Parts and labor are warranted for one year from date of purchase. LIZZRD ORPORTION S WRRNTY REMEDY: lizzard orporation will, at its sole discretion, repair or replace defective parts at no charge. USTOMERS RESPONSIILITY: To obtain warranty service, the purchaser must return the defective snowplow to any uthorized lizzard Dealer. The purchaser must verify the original purchase date. Transportation costs to and from the dealer will be the responsibility of the purchaser. ITEMS NOT OVERED UNDER THIS WRRNTY: This limited warranty does not cover the following: 1. Expendable parts such as cutting edges, plow shoes, hoses, fasteners, blade guides, paint finish, etc. 2. ny snowplow or part thereof which has been repaired or altered by anyone other than an uthorized lizzard Dealer. 3. ny snowplow or part thereof which has been subject to neglect, misuse, accident, improper installation, maintenance, or storage. This includes, but is not limited to, corrosion of any electrical components. 4. Snowplows mounted on vehicles other than those for whom lizzard orporation has provided a specific undercarriage system. 5. lizzard orporation does not assume liability for damage to the purchaser's vehicle resulting from the attachment and use of a lizzard straight blade snowplow. Vehicle risk is the sole responsibility of the purchaser. WRRNTY LIMITTIONS: THIS WRRNTY IS OFFERED IN LIEU OF NY OTHER EPRESS WRRNTY. THE DURTION OF LL IMPLIED WRRNTIES, INLUDING UT NOT LIMITED TO THE IMPLIED WRRNTIES OF MERHNTILITY ND FITNESS FOR PRTIULR PURPOSE, RE LIMITED TO THE DURTION OF THIS WRRNTY. LIZZRD ORPORTION'S LIILITY IS EPRESSLY LIMITED TO REPIR OR REPLEMENT OF DEFETIVE PRTS. LIZZRD ORPORTION SHLL NOT E LILE FOR ONSEQUENTIL, INIDENTL OR ONTINGENT DMGES WHTSOEVER, EVEN IF DMGES RE USED Y THE NEGLIGENE OR FULT OF LIZZRD ORPORTION. State Laws: Some states do not allow exclusion of incidental or consequential damages or the limitations on how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. This warranty does not apply if you purchased your snowplow for other than personal, family, or household use. If purchased for other than personal, family or household use, refer to the lizzard Straight lade ommercial Warranty. 95 IRPRK OULEVRD LUMET, MIHIGN [906] REV 8/01
47 LIZZRD OMMERIL WRRNTY This warranty covers defects in material and workmanship except as set forth below. WRRNTED PRTY: This warranty applies only to the Original Purchaser who purchased this plow from an uthorized lizzard Dealer, for commercial use. TERM OF WRRNTY: This lizzard straight blade snowplow is warranted for the following period: Parts and labor are warranted for one year from date of purchase. LIZZRD ORPORTION S WRRNTY REMEDY: lizzard orporation will, at its sole discretion, repair or replace defective parts at no charge. USTOMERS RESPONSIILITY: To obtain warranty service, the purchaser must return the defective snowplow to any uthorized lizzard Dealer within the warranty period. The purchaser must verify the original purchase date. Transportation costs to and from the Dealer will be the responsibility of the purchaser. ITEMS NOT OVERED UNDER THIS WRRNTY: This warranty does not cover the following: 1. Expendable parts such as cutting edges, plow shoes, hoses, fasteners, blade guides, paint finish, etc. 2. ny snowplow or part thereof which has been repaired or altered by anyone other than an uthorized lizzard Dealer. 3. ny snowplow or part thereof which has been subject to neglect, misuse, accident, improper installation, maintenance, or storage. This includes, but is not limited to, corrosion of any electrical components. 4. Snowplows mounted on vehicles other than those for whom lizzard orporation has provided a specific undercarriage system. 5. lizzard orporation does not assume liability for damage to the purchaser's vehicle resulting from the attachment and use of a lizzard straight blade snowplow. Vehicle risk is the sole responsibility of the purchaser. LIMITS OF LIZZRD ORPORTION S LIILITIES: LIZZRD ORPORTION'S LIILITY IS EPRESSLY LIMITED TO REPIR OR REPLEMENT OF DEFETIVE PRTS. LIZZRD ORPORTION SHLL NOT E LILE FOR ONSEQUENTIL, INIDENTL OR ONTINGENT DMGES WHTSOEVER, EVEN IF DMGES RE USED Y THE NEGLIGENE OR FULT OF LIZZRD ORPORTION. THE FOREGOING WRRNTIES RE ELUSIVE ND IN LIEU OF LL OTHER EPRESSED ND IMPLIED WRRNTIES INLUDING, UT NOT LIMITED TO, THE IMPLIED WRRNTIES OF MERHNTILITY ND FITNESS FOR PRTIULR PURPOSE. This warranty does not apply if you purchased your snowplow for personal, family, or household use. In this case, refer to the lizzard Straight lade Limited onsumer Warranty. 95 IRPRK OULEVRD LUMET, MIHIGN [906] REV 8/01
48 95 irpark oulevard alumet, MI [888] [906] [906] Fax lizzard, Power Plow, WidePass, ucketlade, Power Hitch and Seat inch are trademarks of lizzard orporation. lizzard and Power Plow are registered in the United States Patent and Trademark Office. ll other trademarks and registered trademarks are the property of their respective owners. ll lizzard snowplows are protected by one or more of the following United States Patents: 5,638,618; 5,899,007; 6,178,669; 6,276,076; 6,393,737 and 6,615,513. Other patents pending lizzard orporation. ll rights reserved
Operating Instructions & Parts Manual. Model RCHW100
RING HIR Operating Instructions & Parts Manual Model RHW100 SF ompanies 10939 N. Pomona ve. Kansas ity, MO 64153 customerservices@heinwerner-automotive.com Read this manual and follow all the Safety Rules
More informationUNDERCARRIAGE INSTALLATION INSTRUCTIONS UNDERCARRIAGE HARDWARE KIT FOR MODELS:
UNDERCARRIAGE INSTALLATION INSTRUCTIONS UNDERCARRIAGE HARDWARE KIT 31219 61337 FOR MODELS: FORD F-250/350 SUPER DUTY PICKUP (1999-2005) FORD F-450/550 SUPER DUTY PICKUP (1999-2005) FORD EXCURSION (2000-2005)
More informationTAILGATE SPREADER INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS
A Division of Northern Star Industries, Inc. P.O. Box 788 Iron Mountain MI 49801-0788 www.bossplow.com SMARTHITCH 1100 TAILGATE SPREADER INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS S & CAUTIONS...
More informationPARTS INCLUDED. part description part number qty B chock wheel strap SPRINT speed link pad C coussinet Speed Link SPRINT
SPRINT XT 528001 PRTS INCLUDED C D E L M F G I J H K part description part number qty. mount screw cover 8523510001 1 chock wheel strap 8523285001 1 SPRINT speed link pad C coussinet Speed Link SPRINT
More informationEZ-LIGHT Indicators 4-Color, Multi-Function
EZ-LIGHT Indicators -olor, Multi-Function Datasheet D-Operated Indicators with olors and Multiple Flashing Frequencies Rugged, cost-effective. and easy-to-install indicators available in K0, K0 Flat Pack,
More informationWL50S High-Intensity Work Spot Light
Datasheet General-purpose LED work lighting For the latest technical information about this product, including specifications, dimensions, and wiring, see www.bannerengineering.com. Three lens options,
More informationInstructions. Warnings 2 Setup & Lamp Installation 3 Rear Panel 3 Mounting 4 Accessories 4-6 Warranty, Problems, Repairs & Information 7
Instructions Warnings 2 Setup & Lamp Installation 3 Rear Panel 3 Mounting 4 ccessories 4-6 Warranty, Problems, Repairs & Information 7 Warnings The LowelScandles fluorescent system is a professional lighting
More informationModel FM2260 Wall Mount. Full Motion Television Wall Mount
Model FM2260 Wall Mount Full Motion Television Wall Mount Getting Started Introduction Congratulations on the purchase of your new udio Solutions FM2260 Television Wall Mount. For maximum benefit, please
More informationMega Blade Vehicle Application Guide
Mega Blade Vehicle Application Guide Sno-Way statement regarding the installation of snow plows on vehicles equipped with driver/passenger airbags: A number of vehicle manufacturers have or will be equipping
More informationAIRSCREEN 8700, 8701, 8702, 8703
IRSCRE 8700, 8701, 8702, 8703 = North merican English PRTS INCLUDED C D E F G H I J K L part description 8700 qty. 8701, 8702, 8703 qty. fairing blade 1 1 C D driveside wing non-driveside wing protective
More informationSKID STEER COMBO PLOW
A DIV. OF NORTHERN STAR INDUSTRIES, INC. P.O. BOX 788 IRON MOUNTAIN, MICHIGAN 49801 SKID STEER COMBO PLOW INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS SAFETY PRECAUTIONS... 2 ASSEMBLY PROCEDURE... 3
More informationMega Blade Vehicle Application Guide
Mega Blade Vehicle Application Guide Sno-Way statement regarding the installation of snow plows on vehicles equipped with driver/passenger airbags: A number of vehicle manufacturers have or will be equipping
More informationTGS 1100 & TGS 600 TAILGATE SPREADER INSTALLATION & OWNER S MANUAL
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com TGS 1100 & TGS 600 TAILGATE SPREADER INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS
More informationWARNING Read these materials prior to assembling and using the trampoline and Trampoline Enclosure
R & PowerBounce User s Manual ssembly, Installation, Care, Maintenance, and Use Instructions WRNING Read these materials prior to assembling and using the trampoline and Trampoline Enclosure 1) PowerBounce
More informationEZ-LIGHT Indicators Audible
EZ-LIGHT Indicators udible Datasheet For the latest technical information about this product, including specifications, dimensions, and wiring, see www.bannerengineering.com. QPM EURO-STYLE PIGTIL PUR
More informationOld Seal Kits. Instructions - Parts B. Piston Seal Kits, see page 2. Cylinder Seal Kits for A-Side Pumps, see page 2
Instructions - Parts Old Seal Kits 32348B To replace proportioning pump piston seal sets or cylinder seal sets used on Gusmer and Old Graco H-25 and H-XP2 Hydraulic Proportioners. Important Safety Instructions
More information2017 & NEWER FORD SUPER DUTY RT3 UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA10200)
2017 & NEWER FORD SUPER DUTY (PART NO. LTA10200) DRIVEN TO BE THE BEST MSC10214-A WARNING Many newer trucks are now equipped with air bags. DO NOT under any circumstances disable, remove or relocate any
More informationT-Bones Installation Instructions
T-ones Installation Instructions FINLLY OMPNY THT LOVES IKES S MUH S YOU DO. hances are, your bikes are just like ours - your most valued possessions. nd if it has the Saris name on it, nothing we build
More informationEN main stinger assembly 1. EN bike trays with ratchet arms 2. EN front wheel holder 2. EN rear wheel holder assembly 2.
T2 PRO XT (2" RECEIVER) 9034 (1.25" RECEIVER) 9035 PRTS INCLUDED C D E F G H I J K L M N part description qty. main stinger assembly 1 bike trays with ratchet arms 2 C front wheel holder 2 D rear wheel
More informationInstallation Instructions
Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty Installation Instructions RZT & Z-Force Light Kit Model 19B70032100 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS
More informationMILLENNIUM DEALER PROGRAM GUIDE
Showroom Pre-Owned MILLENNIUM DELER PROGRM GUIDE 1 of 22 MNGEMENT ENVIRONMENTL Pylons Monuments D SERIES 9 7 5 4 PYLON 10 x 15 8 x 12 6 x 8 5 x 6 D SQ. FT. 35-0 2-4 10-5 3/4 15-1 1/2 158.6 30-0 2-0 8-5
More informationInstallation Instructions
Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT 2011 & UP Ford Super Duty F-250/F-350/F-50 2011 & UP Part Number: 50073 WARNING: Under no circumstances do we recommend exceeding the towing
More informationRear Weight Kit 19A , OEM-19A-218 & M060
Operator s Manual Rear Weight Kit 19A-218-000, OEM-19A-218 & 490-900M060 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY
More informationCOVER PAGE CUSTOM QUICK INSTALL MOUNTING KIT NOTE!
COVER PAGE NOTE! Prior to installing product, please visit one of our websites to assure your kit contains the most recent revision to installation instruction and verify vehicle application. www.reeseproduct.com
More informationPROLOGUE 516XT B C D E F G H I M N O P. EN = North American English EN PARTS INCLUDED. EN part EN description EN qty. A EN carriage bolt 6 x 45 2
PROLOGUE 56XT = North merican English PRTS INCLUDED B C D E F G H I J K L M N O P part description qty. carriage bolt 6 x 45 2 B square plate 2 C 3 wing knob M6 x nut 2 D tray end cap E lock plug F Prologue
More informationRear Weight Kit M060
Operator s Manual Rear Weight Kit 490-900-M060 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS
More informationInstallation Instructions
Part Numbers: ALL 5AB-XXXX DEALER/INSTALLER: (1) Provide this Manual to end user END USER: (1) Read and follow this Manual every time you use this product. PIN BOX SHOWN ASSEMBLED Equipment Required: Wrenches:
More informationToyota Tacoma TB TG
INSTLLTION INSTRUTIONS FOR PRT 99-84 KIT FETURES PPLITIONS Toyota Tacoma 005-009 99-84T 99-84TG DIN Head Unit Provision With Pocket ISO DIN Head Unit Provision With Pocket Double DIN Head Unit Provision
More informationSplit Manifold Kits. Installation - Parts List D. Converts Huskyt 307 Diaphragm Pump to dual fluid inlet or outlet
Installation - Parts List Split Manifold Kits 0849D Converts Huskyt 07 Diaphragm Pump to dual fluid inlet or outlet Part No. 2720 For Husky 07 Polypropylene Pumps Part No. 272 For Husky 07 cetal Pumps
More informationINSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES
INSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES DEALER/INSTALLER: (1) Provide this Manual to end user. END USER: (1) Save this Manual for future reference. (2) Pass on copies of Manual to any other
More informationDUSK-TO-DAWN LIGHT MODEL #GU8813-BZ-I, #GU8813-WH-I
ITEM #0333554, #0333553 DUSK-TO-DWN LIGHT MODEL #GU8813-BZ-I, #GU8813-WH-I Utilitech & UT Design and Grounded in Quality are registered trademarks of LF, LL. ll Rights Reserved. Français p. 7 Español p.
More informationBlizzard, PO Box , Milwaukee, WI B32214 UNDERCARRIAGE KIT. Dodge Dakota Dodge Durango
Blizzard, PO Box 245038, Milwaukee, WI 53224-9538 www.blizzardplows.com February 15, 2009 Lit. No. B64052, Rev. 02 B32214 UNDERCARRIAGE KIT Dodge Dakota 1987-04 Dodge Durango 1998-03 Parts List & Installation
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend
More informationSANTA CRUZ BICYCLES MY18 Nomad Exploded Views
SNT CRUZ ICYCLES MY18 Nomad Exploded Views Copyright Santa Cruz icycles 2017 TLE OF CONTENTS SFETY INSTRUCTIONS... 3 REPLCEMENT PRTS... 3 INTRODUCTION...3 TOOLS ND SUPPLIES...3 RER XLE ND HNGER... 4 UPPER
More informationInstallation / Owners Manual
DEALER/INSTALLER: (1) Provide this Manual to end user END USER: Part Number: 94621 94622* *Packaged for Individual sale. (1) Read and follow this Manual for Reese Installation. (2) Save this Manual for
More information2005 & NEWER MITSUBISHI FUSO RT3 UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA09623)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 2005 & NEWER MITSUBISHI FUSO MOUNTING INSTRUCTIONS (PART NO. LTA09623) PUSHING THE EDGE
More informationOWNER'S MANUAL L A W N R O L L E R PRT-481S BH. Safety Assembly Operation Repair Parts Maintenance. Visit us on the web!
OWNER'S MANUAL L A W N R O L L E R ROLLER MODEL: PRC- BH PRT- BH PRT-S BH PRT-S BH Safety Assembly Operation Repair Parts Maintenance Recommended for use with Riding Mowers, Lawn or Garden Tractors, and
More informationINSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES
INSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES DO NOT EXCEED VEHICLE MANUFACTURER S RATING FOR 5th WHEEL TOWING OR MAXIMUM GROSS TRAILER WEIGHT OF 18,000lb. / 8160kg. DEALER/INSTALLER: (1) Provide
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend
More informationOWNERS MANUAL INSTALLATION AND OPERATING INSTRUCTIONS REPAIR PARTS LIST
OWNERS MNUL INSTLLTION ND OPERTING INSTRUCTIONS REPIR PRTS LIST Horizontal Multi-Stage Jet Pumps HMS-1FL Series MODELS 3/4 HP 1 HP 1-1/2 HP HMSD-1FL HMSE-1FL HMSF-1FL ST-RITE INDUSTRIES, INC. 293 Wright
More informationMounting Kit MKPB-QLIV
Mounting Kit F250 Super Duty 4x4 2008-2016 F350 Super Duty SRW 4x4 2008-2016 F350 Super Duty DRW 4x4 2008-2016 F450/550 Super Duty 2008-2016 - For snowplow lights (2008-2015), this kit requires: 800084,
More informationInstallation Instructions **THIS RAIL MOUNTING KIT USES 11 BOLTS**
Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT FORD SUPER DUTY Part Numbers: 50074 WARNING:Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle
More informationSECTION A-A
40.08 D 8 6 5 4 3 2 1 WRNING: IF THERE RE NY DISCREPNCIES ETWEEN THE CD FILE ND THE DRWING, THE DRWING WILL TKE PRECEDENCE. IF IN DOUT, SK. D C 51.1 48 20.25 18 C 23.68 15.12 NOTE: DRWER UNIT NOT INCLUDED,
More information4-LIGHT VANITY FITTER
ITEM #0809648 PORTFOLIO and PORTFOLIO & Design TM are trademarks or registered trademarks of LF, LL. ll rights reserved. 4-LIGHT VNITY FITTER MODEL #VB43-4BNK Français p. 9 Español p. 17 TTH YOUR REEIPT
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill Short & Long Bed All Megacabs 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION WARNING: Under no circumstances do we
More informationSplit Manifold Kits. Installation Parts List C. Converts Husky 307 Diaphragm Pump to dual fluid inlet or outlet
Installation Parts List Split Manifold Kits 0849C Converts Husky 07 Diaphragm Pump to dual fluid inlet or outlet Part No. 2720 For Husky 07 Polypropylene Pumps Part No. 272 For Husky 07 cetal Pumps Important
More informationPRODUCT MANUAL GEARCAGE SYSTEM - ASSEMBLY, INSTALLATION, AND OPERATION INSTRUCTIONS: Description
Gearage -FP6 Hitch Rack TwinTube ased Slide-Out Mounting System PROUT MNUL Installation & Safe Use Operation Highlights Fits 2 size receiver hitches. Rated for 300 lbs of cargo payload. lass II minimum
More informationInstallation Instructions GOOSENECK MOUNTING KIT Toyota Tundra
GOOSENECK MOUNTING KIT Toyota Tundra 446 Equipment Required: Fastener Kit: 446F Wrenches: 10mm, 1mm, /4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Do not store hitch ball upside down in head.
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 15/16, 10 mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING: Under
More informationSELECTION LIST REVISION Form #
SELECTION LIST ---------- REVISION 0 ---------- Form #64136-120102 WESTERN PRODUCTS P.O. BOX 245038 MILWAUKEE, WISCONSIN 53224-9538 A Division of Douglas Dynamics, L.L.C. Printed in the U.S.A. The following
More information36" Galvanized Direct Drive Hyflo Fan Installation and Operators Instruction Manual. Fan and Framing Dimensions
6" Galvanized Direct Drive Hyflo Fan Installation and Operators Instruction Manual Fan and Framing Dimensions Planning the layout of the spacing between Fans is very important. Spacing too close together
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 13mm Drill Bits: 1/4, some older models a 1/2 Other Tools: Drill, Saber Saw 5/8 Fasteners From Hitch Fastener Kit Installation Instructions GOOSENECK
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 10mm, 18mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw 9465/9475 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING:
More informationTable of Contents Multiplexing Installation Multiplexing truck chart...2 Multiplexing installation - module installed under the power unit cover (53618-M)..5 Multiplexing installation- under hood (53618-02-M)
More informationPK Installation Instructions for the 2CPS Series Cable Pull Switch Without Broken Cable Detection ISSUE 3. Sensing and Control
ISSUE 3 Installation Instructions for the 2PS Series able Pull Switch Without roken able Detection PK 80169 WRNING IF USED IN PPLITIONS ONERNING HUMN SFETY Only use N direct opening ( positive opening
More informationAssembly, Installation, Operation and Maintenance Instructions. Base Rail Bracket Kit. For updates see PRODUCT SUPPORT tab at
Assembly, Installation, Operation and Maintenance Instructions P/N: 31408 Base Rail Bracket Kit For updates see PRODUCT SUPPORT tab at www.huskytow.com Provide a copy of these Instructions to the end user
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers
More informationSAFETY INSTRUCTIONS. A) Unroll cover toward tailgate. B) Position header into header stops. Rotate header down and press to lock toggle into header.
STEP 7: operation While driving vehicle, Shur-ond VELCRO brand fasteners must be secured along entire length of cover to prevent wind lift. For best results, leave cover fastened to side rails while opening.
More informationSERIES. Gooseneck OWNER S MANUAL. for Ford and Dodge Tow Prep Kits
SERIES by Gooseneck OWNER S MANUAL for Ford and Dodge Tow Prep Kits #4436 30K OE Series Gooseneck Ball #4437 30K OE Series Gooseneck Ball w/ Plate Gross Trailer Weight (Maximum) Vertical Load Weight (Max.
More informationOperator s Manual. Twin Rear Bagger For FastAttach Compatible Lawn Tractors
Operator s Manual Twin Rear Bagger For FastAttach Compatible Lawn Tractors Models OEM-190-601 (for 38-inch & 42-inch decks) OEM-190-602 (for 46-inch decks) MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND,
More informationODY-05-2 VOLTMETER FOR REMOTE MONITORING
ODY-05-2 VOLTMETER FOR REMOTE MONITORING Introduction: The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our standard gauges, along with several unique features
More informationODY-01-1 or ODY-01-2 SPEEDOMETER
ODY-01-1 or ODY-01-2 SPEEDOMETER Introduction: The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our standard gauges, along with several unique features and
More informationPREMIUM HITCH MOUNT PLATFORM BIKE CARRIER
model no. 040-96-2 PREMIUM HITCH MOUNT PLTFORM BIKE CRRIER NOTE: Read instructions carefully before installation. Refer to assembly instructions and ensure the bike carrier is installed correctly. Keep
More informationPlow Partner Mounting Kit M
Plow Partner Mounting Kit 59-M Page Warning Plow Partner Mounting Kit Do not exceed GVWR or GAWR, including blade and ballast. The rating label is found on the driver side vehicle door corners. Lower
More informationV-X T & DXT BLADE WING EXTENSION KIT INSTALLATION INSTRUCTIONS
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com V-X T & DXT BLADE WING EXTENSION KIT INSTALLATION INSTRUCTIONS Kit Number: MSC08063B
More informationAssembly, Installation, Operation and Maintenance Instructions. Base Rail Bracket Kit. For updates see PRODUCT SUPPORT tab at
Assembly, Installation, Operation and Maintenance Instructions P/N: 32831 Base Rail Kit For updates see PRODUCT SUPPORT tab at www.huskytow.com Provide a copy of these Instructions to the end user of this
More informationAEROMOTIVE Part # INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 16306 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried
More informationMaxLite LED Linear HighBay Fixtures
Operating Instructions MaxLite LED Linear HighBay Fixtures General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions,
More informationVertical Lift:
70068 Vertical Lift: Frame ssembly Instructions. Model: 70068-0ft Wide 7000lb apacity - Part #: 0070. 2. 3.. 5. UTION - PUT SFETY FIRST Before attempting to install or operate this lift, study and fully
More informationModel 1001/1001HPS Drinking Fountain
INSTLLTION, OPERTION & MINTENNCE INSTRUCTIONS Kleppe Lane Sparks, NV 89-667 (77) 9-72 Fax (77) 9-72 E-mail: haws@hawsco.com website: www.hawsco.com Model 00/00HPS Drinking Fountain No. 20760(9) NOTE TO
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 15/16, 10 mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw 9464/9474 HIDE-A-GOOSE HITCH All Fasteners Typical, Both Sides
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle
More informationHi-Rise 18K 5TH WHEEL CONVERSION HITCH
ASSEMBLY INSTRUCTIONS Hi-Rise 18K 5TH WHEEL CONVERSION HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. END USER: (1) Read and follow this Manual every time you use Hitch. (2) Save this Manual
More informationAGCO Conversion Manual a HEADSIGHT.COM
AGCO 3300 Conversion Manual 09040404a HEADSIGHT.COM 574.546.5022 About Headsight Headsight Contact Info Headsight, Inc. 4845 3B Road Bremen, IN 46506 Phone: 574-546-5022 Fax: 574-546-5760 Email: info@headsight.com
More informationLED SEMI-FLUSHMOUNT CEILING FIXTURE
ITEM #0760102 LED SEMI-FLUSHMOUNT EILING FIXTURE MODEL #SFL11BNK Français p. 9 Español p. 17 TTH YOUR REEIPT HERE Serial Number Purchase Date E465631 Questions, problems, missing parts? Before returning
More information3/8" Square Multi-Turn Cermet Trimmer
www.vishy.om 3/8" Squre Multi-Turn Cermet Trimmer Vishy Sfernie FEATURES Industril grde W t 70 C Tests ording to CECC 41000 or IEC 60393-1 The is smll size trimmer - 3/8" x 3/8" x 3/16" - nswering PC ord
More information2008 & NEWER DODGE 4500/ & RT3 UNDERCARRIAGES MOUNTING INSTRUCTIONS (PART NO. LTA09300 & LTA09320)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 2008 & NEWER DODGE 4500/5500 10 & RT3 UNDERCARRIAGES (PART NO. LTA09300 & LTA09320)
More informationMSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740
MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issued with
More information5 th Airborne Sidewinder Service Kit Instructions 94316
94316 Equipment Required: Wrenches: 15/16, Torque Wrench, Rubber Mallet 3 4 5 2 Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (1) Wear Bushing 3 Qty. (1) Wear Disc 4 Qty. (4) 5/8-11x2 GRD8 Bolt
More informationInstallation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab
GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers
More informationModels 8100PP & 86110LP. Installation Instructions CAUTION. Read this document before installing the snowplow. CAUTION
September 15, 2010 Lit. No. 48645, Rev. 02 POWER PLOW Snowplows Models 8100PP & 86110LP Installation Instructions Read this document before installing the snowplow. See your BLIZZARD outlet/web site for
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 13mm Drill Bits: 1/4, some older models a 1/2 Other Tools: Drill, Saber Saw 5/8 Fasteners From Hitch Fastener Kit Installation Instructions GOOSENECK
More informationMicroscope light manual
Microscope light manual LS-12 and LS-14 LS-12 LS-14 1/9 Content Overview... 3 Mounting... 4 Light adjustment... 5 Mirror... 6 Filters... 6 Replacing microscope light... 7 Technical data... 8 Troubleshooting...
More informationLUBRICATOR GUN INSTRUCTIONS-PARTS LIST. 10,000 psi (700 bar) Maximum Delivery Pressure. Detachable-type
INSTRUCTIONS-PARTS LIST 306 460 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. E Supercedes D Detachable-type LUBRICATOR GUN 10,000 psi (700 bar)
More information2007 Ram Snowplow Installation
INTRODUCTION The factoryinstalled Snowplow Preparation Groups (or their equivalent components) are recommended and listed for each vehicle. The normal warranty applies to Dodge Ram trucks that have after
More informationWL50-2 LED Work Light
General-Purpose LED Work Lights Shown are flat-mount model with push-button (left) and 0 mm base-mount model without the push-button Designed for enclosure or area lighting Use with an optional flex arm
More informationSafety Assembly Operation Service and Adjustment Repair Parts 1602 CORPORATE DRIVE, WARRENSBURG MISSOURI PHONE FAX
swisherinc.com OWNER S MANUAL MODEL NO. 12019 12019A Blade Mount Adaptor IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. REV 11-283 Safety Assembly Operation
More informationDODGE DAKOTA RT3 UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA04902)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 2000 2004 DODGE DAKOTA RT3 UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA04902) PUSHING
More informationCMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION
CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION Thank you for purchasing the CMD-4000 series Remote Control Door Latch Opener System from Dakota Digital, Inc. This,
More informationAEROMOTIVE Part # INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 16302 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried
More informationL-BRACKET INSTALLATION
L-BRACKET INSTALLATION Consult the omplete Instlltion Guide for ll other spets of fn instlltion nd sfety guidelines. WARNING: The fn should not e instlled unless the struture on whih the fn will e mounted
More informationOwner s Manual SB5010 Broadcast Spreader. Caution: Read all Safety Instructions and Operating Instructions Carefully.
Manufacture s Limited Warranty for Broadcast Spreader Owner s Manual SB00 Broadcast Spreader The limited warranty set forth below is given by Precision Products Incorporated with respect to new merchandise
More informationDTC C1268/68 Transfer "L4" Position Switch Circuit
RKE ONTROL VEHILE STILITY ONTROL SYSTEM 135 DT 1268/68 Transfer "L4" Position Switch ircuit DESRIPTION fter confirming that the transfer is in the L4 position, -TR and downhill assist control will be activated
More information16K and 19K Sidewinder TM Service Kit Instructions 86005
86005 Equipment Required: Wrenches: 15/16, 1 1/8, Torque Wrench, Rubber Mallet Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (6) 5/8 Conical Washer 3 Qty. (2) Wedge Bolt, 5/8-11 X 1 3/4 GRD
More informationAGCO / Gleaner Walker MAV Complete Chopper Installation Guide
TM GCO / Gleaner Walker MV - 500 Complete Chopper Installation Guide C004-01_R2 DEC 2011 ROTOR LDE IMPORTNT! The paddle blades, located on the balance rings inside the chopper, must be installed in the
More information16K Revolution Service Kit Instructions 86016
86016 Equipment Required: Wrenches: 15/16, 1 1/8, Torque Wrench, Rubber Mallet Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (1) Pivot Bushing 3 Qty. (1) Bearing Cup 4 Qty. (1) Bearing 1 5 Qty.
More informationInstallation Instructions PART NUMBERS: 76128, 84128, CQT76128
Installation Instructions LIMITED LIFETIME WARRANTY To prevent SERIOUS INJURY, DEATH or PROPERTY DAMAGE: ALWAYS read, understand and follow warnings and instructions for your hitch BEFORE installation.
More informationModel IMX1. Back Cushion
Invacare Matrx MX1 Model IMX1 ack ushion User Manual EN This manual MUST be given to the user of the product. EFORE using this product, read this manual and save for future reference. This product complies
More informationmetric BOlTS: 42 ft/lbs.
Subaru Outback 11-13 TP20272,Rev.1 BOlT TORQuE SPECIfICATIONS STANDARD BOlTS: Size grade Torque 5/16 5 20 ft/lbs. 3/8 5 35 ft/lbs. 7/16 5 56 ft/lbs. 1/2 5 85 ft/lbs. metric BOlTS: Size 8mm 10mm 12mm 14mm
More informationOWNER S MANUAL 40 LAWN AERATOR SAT-40 BH. Assembly Installation Operation Repair Parts. Visit us on the web! MODEL:
OWNER S MANUAL 40 LAWN AERATOR MODEL: SAT-40 BH Assembly Installation Operation Repair Parts For the latest product updates & setup tips: Visit us on the web! www.brinly.com Important: This manual contains
More information