GEN Series with Diesel Engine Pumps

Transcription

1 GEN Series with Diesel Engine Pumps Fire-fighting booster sets EN 1284, high-efficiency electric pumps with PLM motors and series FHF and SHF horizontal centrifugal diesel engine pumps Hz

2 WEB

3 CONTENTS General introduction... 1 Characteristics of electric pumps diesel engine pumps Accessories and main components Choice and selection GEN..D/FHF series Range Hydraulic performance tables Electrical performace tables...3 DFHF series... 9 GEN..D/FHF series GEN..1D/FHF series GEN..1D/FHF series GEN..11D/FHF series Hc pressure drop curve in suction kit

4 CONTENTS 91 GEN..D/SHF series Range Hydraulic performance tables Electrical performance tables DSHF series GEN..D/SHF series GEN..1D/SHF series GEN..1D/SHF series GEN..11D/SHF series Hc pressure drop curve in suction kit Accessories Product description by technical specifications

5 GEN SERIES OF BOOSTER SETS GENERAL INTRODUCTION PRODUCT DESCRIPTION The GEN booster sets are built in conformity with EN1284 for automatic sprinkler systems and with UNI1779 for hydrant systems. In accordance with the above standards, all the main components of the booster set are factory connected and assembled. The configuration of the booster set depends on the number of pumps installed and on the type of electric motor or diesel engine, consistently with the type of supply chosen for the fire-fighting system from among those described in the standard. The water supply can be single, superior, duplicated or combined. Two main service pumps, one backing up the other, are normally installed for fire-fighting systems. The choice of electric motors or diesel engines depends on the level of reliability required from the system. In practice, fire-fighting booster sets have one electric service pump and one diesel service pump. Point 1.2 of EN 1284 states that for superior or duplicate water supplies, and if more than one pump is installed, no more than one service pump can be driven by the electric motor. This concept means that mixed assemblies, comprising electric or diesel pumps, have to be installed. This does not mean that it is not possible to have two electric pumps, one backing up the other, if the ascertained fire risk is low (single supplies) or if a diesel generator is already incorporated in the system. The GEN series of booster sets are therefore configured according to system requirements and initial considerations. They are also factory tested and comprise the following: One or two horizontal or vertical service pumps with the same hydraulic performance level, driven by an electric motor. Two horizontal service pumps with the same hydraulic performance level, driven by an electric motor and a diesel engine. A horizontal service pump driven by a diesel engine. The booster set is built and completed with the following main components: A SV series jockey electric pump (if required), controlled by an electric panel in the automatic mode. The jockey pump is automatically started and stopped by its pressure switch in order to restore supply pressure. This prevents the service pumps from starting and activating the main alarms. A control panel for each service pump. Two pressure switches for each service pump (if the first fails, the second repeats permission for the pump to start). On the discharge side of each service pump there is a on-off valve, a check valve and a tap for connection to the priming circuit for suction lift installations. Moreover, if the service pump works with a closed discharge line, a water recirculation tap has been applied to the pump body in order to prevent the pump from overheating. Discharge manifold connected to each service pump, fitted with a weld-on flange for connection to the system. Single base containing all the booster set components within a compact structure and ready for installation. To complete the pump station as requested by the standard, the GEN series of booster sets are fitted with the following accessories: Suction side kit. Flow meter. Alarm panel. Set of spare parts for diesel engines. Priming tank with accessories (for suction lift installations). 24L diaphragm tanks.

6 SET IDENTIFICATION TION CODE DIESEL ENGINE PUMP D FHF E A X / 32-2/D24 / B / IP Options: IP = Panels with IP protection. _ = Language group IT, EN, FI, PT. B = Language group EN, FR, DE, NL. Pump model. X = Automatic shut-off. A = Version with periodic self-test. EN 1284 Fire-fighting series. FHF = Pump code. SHF = Pump code. Diesel engine pump. DIESEL ENGINE PUMP SET GEN A X D / FHF 32-2/D24 / B / IP Options: IP = Panels with IP protection. _ = Language group IT, EN, FI, PT. B = Language group EN, FR, DE, NL. FHF = Pump code. SHF = Pump code. Diesel engine pump only. X = Automatic shut-off. A = Version with periodic self-test. GEN Fire-fighting series. RU SET WITH DIESEL ENGINE PUMP AND ELECTRIC PUMP GEN Y B X 1 1 D / FHF 32-2/4/D24 + SV29 / B / IP Options: CP = Clean contacts in electric pump panel. IP = Panels with IP protection. KV = Voltmeter kit. _ = Language group IT, EN, FI, PT. B = Language group EN, FR, DE, NL. Jockey pump code. FHF = Service pump code. SHF = Service pump code. D = With diesel engine pump. = Without electric jockey pump. 1 = With electric jockey pump. = Without electric service pump. 1 = With 1 electric service pump. X = Automatic shut-off. B = Basic version (only mark if electric service pump is present). A = Version with periodic self-test. Electric service pump electric start-up D = Direct start (Up to and including 22 kw). Y = Star/delta start. I = Impedance start. GEN Fire-fighting series. 6

7 REFERENCE STANDARDS The fire-fighting booster sets are CE marked for conformity with the following directives: - Machinery Directive 98/37/EC. - Low Voltage Directive 26/9/EC. - Electromagnetic Compatibility Directive 89/336/EEC as amended. The performance of the electric pumps is declared to comply with the following standard: ISO 996-A Rotodynamic pumps hydraulic performance acceptance tests. The fire-fighting booster sets comply with the European fire-fighting Standard EN The automatic shut-off version also complies with the UNI 1779 Italian Standard for hydrant systems. 7

8 GEN SERIES OF BOOSTER SETS FUNCTIONAL DIAGRAM FOR POSITIVE SUCTION HEAD INSTALLA ALLATIONS GEN SERIES OF BOOSTER SETS FUNCTIONAL DIAGRAM FOR SUCTION LIFT INSTALLA ALLATIONS 8

9 GEN SERIES OF BOOSTER SETS MECHANICAL CONFIGURATION REF. DESCRIPTION REF. DESCRIPTION 1 electric service pump 1 divergent on discharge line 2 diesel engine service pump 11 inspectable check valve 3 jockey pump discharge line 12 on-off valve on discharge line 4 control panels 13 pressure gauge pump suction line 14 discharge manifold 6 on-off valve on suction line 1 service pump starter (2x) 7 eccentric divergent 16 diaphragm tanks 8 vacuum pressure gauge 17 priming circuit tap 9 anti-vibration joint 18 recirculation circuit tap gen11d-comp-en_a_tp 9

10 CHARACTERISTICS S OF THE PUMPS USED IN THE GEN SERIES OF BOOSTER SETS SV2, 4, 8 ELECTRIC PUMPS (JOCKEY PUMP) Multistage centrifugal vertical electric pumps. All metal parts in contact with pumped liquid are made of stainless steel. Version F: round flanges, in-line discharge and suction ports, AISI 34 (Standard version). Version N: round flanges, in-line discharge and suction ports, AISI 316 (Available on request). Reduced axial thrusts enable the use of off-the-shelf standard motors. The performance levels of PLM surface motors lie within what is usually referred to as efficiency class 1. Mechanical seal according to EN 1276 (ex DIN 2496) and ISO 369. Easy maintenance. No special tools required for assembly or disassembly. For other characteristics, consult the relative dedicated technical catalogue. FHF32, 4,, 6, 8, 1, 12 PUMP SERIES Single impeller cast iron horizontal centrifugal pump and shaft made of AISI 316L stainless steel. End suction and radial discharge ports. Impeller: made of AISI 316L stainless steel laser technology welded, for sizes 32, 4,, 6-12, or cast iron for sizes 6-16, 6-2, 6-2, 8, 1, 12. Hydraulic sizes and nominal diameter DN of suction and discharge ports according to EN 733 (ex DIN 242). Flanges according to EN (ex UNI 2236) and DIN 232. Motor: motor/pump coupling with bracket, support, flexible coupling with spacer coupling and aligning and anchoring base. The performance levels of PLM surface motors lie within what is usually referred to as efficiency class 1. Performance levels according to EN Back pull out design, impeller, adaptor and motor can be extracted without disconnecting the pump body from the pipes. For other characteristics, consult the relative dedicated technical catalogue. SHF32, 4,, 6, 8 PUMP SERIES Single impeller horizontal centrifugal pump with pump body and shaft made of AISI 316L stainless steel. End suction and radial discharge ports. Closed impeller made of AISI 316L stainless steel laser technology welded (for sizes 2, 32, 4,, 6-16/7 and 6-16/11A) or AISI CF8M cast stainless steel. Hydraulic sizes and nominal diameter DN of suction and discharge ports according to EN 733 (ex DIN 242). Flanges according to EN (ex UNI 2236) and DIN 232. Motor: motor/pump coupling with bracket, support, flexible coupling with spacer coupling and aligning and anchoring base. The performance levels of PLM surface motors lie within what is usually referred to as efficiency class 1. Performance levels according to EN Back pull out design, impeller, adaptor and motor can be extracted without disconnecting the pump body from the pipes. For other characteristics, consult the relative dedicated technical catalogue. 1

11 MAIN COMPONENTS FIRE-FIGHTING DIESEL ENGINE PUMP (D..) Diesel engine with coupling to service pump. Electric panel for control of diesel engine pump and battery charger. Diesel engine start circuit with two independent batteries. Double engine starting relay. Engine shut-off device from electric control (Electric stop). Fuel tank for diesel engine equipped with float. Base made of structural steel with epoxy powder painting RAL 1. The diesel engine pump is mounted on its own base complete with vibration-damping feet, and comes with a wall-mounted electric panel fitted with 3-metre cables ( metre length available on request), fuel tank with wall or floor mounting depending on capacity, floor-mounted or on-board batteries. Special versions of additional diesel fuel tank available on request. A panel mounting bracket kit for floor mounting and a jockey pump kit can be supplied on request. The installation of the diesel engine must provide for adequate ventilation and exhaust of combustion fumes. FIRE-FIGHTING SETS WITH DIESEL ENGINE PUMP (GEN..D) FIRE-FIGHTING SETS WITH ELECTRIC PUMP AND DIESEL ENGINE (GEN..D) On/off valves on the delivery side of each pump, ball valves with lever handle for diameters up to and including 1" 1/2 butterfly valve with lever handle from DN to DN1 diameter, butterfly valve with handwheel and reduction manual gear for DN12 diameter and above. Device for monitoring ON/OFF status included. Electrical connections by customer. (Lockable kit available on request). Recirculation device for each service pump. The re-circulation device allows a minimum capacity in order to prevent the pump overheating when working with closed delivery. It includes the activation pressure switch for the alarms of the pumps running, the test valve for checking the seal of the check valves, the couplings for any connecting pipes to the priming tank in the case of suction lift installation. The connection of each re-circulation to the suction tank or the priming tank is to be seen to by the person installing the equipment. Pressure gauge on the delivery side of each service pump between check valve and on/off valve. Inspectable check valve on the discharge side of each pump. Threaded coupling for diameters up to 1"1/2 included, flanged coupling for larger sizes. Painted iron delivery manifold (PN 16) and threaded stubs with relative caps for connecting any 24 litre membrane tanks. Blind and welding zinc-plated flanges. Two start-up pressure switches for every service pump. For the electric service pumps, start-up takes place through the pressure switch, but it must be manually stopped using the key-operated selector switch on the panel (excluding the version with automatic shut-off). For the electric jockey pump, if present, both start-up and stopping are determined by the pressure switch. Start-up pressure switch circuit for the service pump, including connecting pipes for the delivery manifold, recirculation circuit. This circuit includes on/off valve, a non-return valve, a discharge valve and various pipe fittings. The configuration of the circuit allows the pressure switch to intervene also when the relative on/off valve is closed. Various pipe fittings (copper, zinc-plated steel). Base made of bent sheet or structural iron with epoxy powder painting RAL 1. Control panel frame made of structural iron with epoxy powder painting RAL 1. Diesel engine with coupling to service pump. Vibration-damping joints on discharge side. Electric panel for control of diesel engine pump and battery charger. Diesel engine start circuit with two independent batteries. Length of cable connecting the batteries to the connection box 3 m. Double engine starting relay. Engine shut-off device from electric control (Electric stop). 11

12 Fuel tank for diesel engine. Special versions of additional diesel fuel tank available on request. Electric panel for each electric service pump. Starting: Direct (DOL) up to and including 22 kw, star/triangle from 3 kw up. The diesel engine pump is mounted on its own base complete with vibration-damping feet, and comes with a wall-mounted electric panel fitted with 3-metre cables ( metre length available on request), fuel tank with wall or floor mounting depending on capacity, floor-mounted or on-board batteries depending on size. A panel mounting bracket kit for floor mounting and a jockey pump kit can be supplied on request. The installation of the diesel engine must provide for adequate ventilation and exhaust of combustion fumes. The control panels for the electric pumps up to kw power supply are fixed on bracket. For higher powers, the control panels for electric pump service are floor mounted, instead the jockey electric pump panel is wall mounted fixed. Sets featuring a single diesel engine pump plus jockey pump are equipped with electric jockey pump with 1 x 23V single-phase power supply. SUCTION KIT The set is supplied with its suction side free from components. On request, for the SUCTION side of the individual service pump, TWO versions are available according to the system s installation type: POSITIVE SUCTION HEAD and SUCTION LIFT KIT Kit suitable for positive suction head or suction lift installation. The suction side of the individual pump includes: - Anti-vibration joint to attach to the pump inlet. - Eccentric cone or flanged stub pipe. - Vacuum pressure gauge. - On/off butterfly valve with lever handle for diameters up to DN1, butterfly valve with handwheel and reduction manual gear for DN12 and higher. Device for monitoring ON/OFF status included. Electrical connections by customer. (Valve lock kit available on request). - Weld-on flange. Conforming to the requirements of the EN 1284 Standard (chapter 1. and chapter 1.6). These requirements are connected with the type of installation and the measurement of the piping sections. (see tables on pages ). OTHER VERSIONS As well as the basic GENDB versions (direct start-up), GENYB (star triangle start-up), GENIB (impedance start-up), the following versions are also available: GEN..A With periodic self-test function. There is a self-test circuit including a weekly clock on the electric panel of each electric service pump. For the time and date pre-set, the pump is started up and kept functioning for 1 minute. During this interval the check circuit checks that the pressure in the re-circulation circuit closes the pressure switch contact of the pump which is running. In the case of irregularities, the relative auxiliary self-test alarm relay available for remote signalling is activated and memorised. The EN1284 Standard does not provide for the presence of a self-test circuit but asks for periodic checks to be carried out by the user, hence the periodic self-test function cannot substitute the above checks. GEN..X GEN..X (For fire hydrant systems, UNI 1779) With automatic shut-off. There is an automatic shut-off circuit on the electric panel of each electric service pump. In certain situations, it allows automatic shut-off once the system pressure has been kept at higher values than the start-up values for at least twenty minutes. The self-test and automatic shut-off versions are available for each type of GEND.., GENY.., GENI.. start-up and in combination between them (See identification codes page). 12

13 ACCESSORIES SORIES AVAILABLE AILABLE ON REQUEST Protection against dry running for the electric jockey pump in one of the following versions: - Float switch, in case of suction lift. - Probes kit in case of suction lift (needs optional probe module in the electric jockey pump). - Minimum pressure switch, in case of positive suction head. Electric panel for remote status and alarm monitoring of one or two pumps installed in GEN fire-fighting booster sets, according to EN1284. In the electric service pump mode, the following conditions are visualised: Motor powered, pump start-up request, pump running, failure to start. In the diesel engine service pump mode, the following conditions are visualised: switch in non-automatic position, diesel engine fails to start after 6 attempts, pump running, QAL1284 Panel controller failure. Additionally: minimum suction tank or fuel level, minimum priming tank level, on-off valve on suction and discharge side not fully open. All the above conditions, required by EN1284, are visualised with signal LED s and buzzers. A buzzer alarm reset button and LED tester button are included. The control unit is also fitted out to signal the following general alarms, if present: - General alarm for incorrect electrical connection in the exchange contacts of: flow meter circuit valve, discharge pump, jockey pump status. - Fault in electrical connection in the exchange contact relative to panel 1 (electric pump/diesel engine pump). - Fault in electrical connection in the exchange contact relative Flow meter to panel 2 (electric pump/diesel engine pump). - Jockey pump overload; - Jockey pump running; - Discharge pump overload; - Battery low; - No communication with ModBus system. All the above conditions are visualised with signal LED s and on the display. The customer may decide to enable the buzzer. Further information available on page 144. Circuit for test flow of the service pumps. Includes the direct reading flow meter (sized according to the capacity of the service pump) according to the type of flow meter, connecting piping and straight piping upline from the instrument, on/off ball valve for diameters up to and including 2 butterfly valve with lever handle from DN6 to DN1 diameter, butterfly valve with handwheel and reduction manual gear for DN12 diameter and above. ON/OFF status monitoring included. New model of flow meter (P6) for diameters up to and including DN8. Diaphragm tank with relative ball valve, in the same number as that of the pumps present, for dampening any pressure oscillations in the system. 24 litre model with maximum pressure 8.1 or 16 bar according to the maximum head of the pumps. Priming tank for each service pump, in the case of suction lift installation. Accessories for the priming tank suck as float switch tap, level indicator, valves, automatic air discharger on each service pump, in the case of suction lift installation. All the main characteristics of the priming tanks, the flow meters and the available membrane tanks are shown in the accessories section. 13

14 SPECIAL EQUIPMENT ON REQUEST (Contact the Sales and technical Assistance Service) Sets for pumping sea water with electric pumps, valves, manifold and AISI 316 piping or compatible alloys. Non-standard supply power sets. Sets with two diesel engine service pumps. (See page 1). Sets with separate electric jockey pump supplied as a kit. Sets with different electric jockey pump from the standard one. Sets installed inside prefabricated boxes for outdoor use. Sets with oversized fuel tank. Sets with diesel engine pump with compressed air start system. Diesel engine pump with ambient air cooling device. Notes The set is supplied without a suction manifold in accordance with the EN1284 Standard (points and ) which provides for independent suction for each pump. Please see the EN1284 Standard on fixed systems and fire extinguishing Automatic sprinkler systems Design, installation and maintenance?- for sizing the suction piping, define whether the installation is to be considered suction lift or positive suction head for the use limits. The Standard ask that, whenever possible, the pumps are installed with positive suction head, otherwise priming tanks must be provided with suitable automatic devices for signalling and reintegration. The EN1284 Standard states that the water pressure should not exceed 12 bar (point 8.2.1). In some applications it is possible to have pressures of over 12 bar (point 8.2.2). In this case, pump sets with higher pressures than those within the regulatory limit are used. The catalogue also shows booster sets with pump closing head up to 1 metres suitable for such installations. 14

15 SPECIAL EQUIPMENT ON REQUEST 1

16 COMMAND PANEL FOR THE ELECTRIC SERVICE PUMP Painted metal casing (IP 4) complete with: General door-locking switch. Analogical ammeter. MAN AUT selector with extractable key only in automatic position. Keyboard for indicating electric voltage presence, correct phase sequence (three phase power supply), start-up request, pump functioning and no start-up, through LED lamps, lamp test button and starting and stopping buttons, according to the provisions of EN1284 paragraph Inside: 12/24V transformer for auxiliary circuits and electronic board. Fuse holder and fuses for power and auxiliary circuits. Line contact maker (direct start-up up to 22 kw included), line and star/triangle contact makers (startriangle start-up), line contact makers and reactance switching (impedance start-up). Star/triangle exchanger timer or reactance switching. Relay for signalling no phase. Auxiliary relays. Current transformer. Terminal boards. Clean contacts (max. 24V, 1A) for activating acoustic/ visual alarms for no phase, pump on demand, pump running and start failure. Cable glands (excluding the versions to be fixed to the floor). Wiring diagram. On request digital trasmission card via RS48 serial by ModBus comunication protocol. Electric service pump panel 16

17 COMMAND PANEL FOR THE ELECTRIC JOCKEY PUMP Painted metal casing (IP ) complete with: General door-locking switch. Visual indicators for line, running, thermal shutdown. Manual automatic selector excluded. Inside: Transformer for 24V auxiliary circuits. Fuse holder and fuses for power and auxiliary circuits. Line contact maker. Overload cut-out switch. Pump shut-off timer ( 9 s). Terminal boards. Cable glands. Wiring diagram. Suitable for connecting to a float switch or a minimum pressure switch for preventing dry running. An optional level control module (supplied on request) allows the connection of probes with the possibility of regulating the sensitivity according to the hardness of the water. Electric jockey pump panel OPTIONS AVAILABLE AILABLE ON REQUEST CP alternative Series of clean contacts for checking the status of the electric service pump panel, as well as the contacts already provided for signalling alarms: No phase Motor running Selector position MAN-AUT- No start-up Start-up request Series of clean contacts for checking the status of the electric jockey pump: Pump running Thermal shutdown (overload) No water KV alternative Control panel for the electric service pump with analogical voltmeter and with phase switch. IP alternative Electric service pump panel with extra IP protection. 17

18 COMMAND PANEL FOR DIESEL ENGINE PUMP Painted metal casing (IP 4) complete with: Electronic control and management unit for the diesel engine. Display of alarms and status, battery voltage, speedometer, hour counter, alarm programming, date display, main signals and manual start button. Man-Auto- selector switch with key removable only in the auto position. Pair of emergency battery start buttons. General door-locking switch. Inside: Fuse holder and fuses for power and auxiliary circuits. Pair of battery chargers 12Vdc/24Vdc. Control unit for management of diesel engine and alarms. Auxiliary relays. Power circuits for engine heaters. Terminal boards. RS232 connector for communication port. Cable glands. Wiring diagram. Diesel engine pump panel The panel is supplied standard with clean alarm signal contacts (max. 1A,3Vdc/12Vac/277Vac): Non-automatic operating mode. Controller fault. Motor running. Failure to start. General alarm. On request digital trasmission card via RS48 serial by ModBus comunication protocol. Single-phase 1x23V standard power supply. OPTIONS AVAILABLE AILABLE ON REQUEST IP alternative Diesel engine service pump panel with additional IP protection. The set is supplied already assembled, calibrated and factory tested. The set is supplied complete with an instruction manual, pump manuals and wiring diagrams for the panels. For the sets including floor panels, the electric panels are sent together with the set in a separate pack and supplied with -metre long connecting cables (longer lengths available on request). The fitter is responsible for preparing the routes and installing the cables. 18

19 COMMAND PANEL DIMENSIONS SERVICE PUMP PANEL POWER (kw) PROTECTION B L H CLASS from,7 to 7, IP from 9,2 to 22 IP from 3 to 37 IP4 2 7 from 4 to IP from 7 to 9 IP from 11 to 16 IP IP: same dimensions as standard panels IP4 qe-serv-en_d_td Power over kw: floor cupboard JOCKEY PUMP PANEL PROTECTION CLASS B L H IP IP: same dimensions as standard panels IP4 qe-pil-en_b_td ENGINE PUMP PANEL PROTECTION CLASS B L H IP4 3 2 IP: same dimensions as standard panels IP4 qe-mtp1284_en_b_td * The control panels are included in the supply. 19

20 EN 1284 DIESEL ENGINE PUMP TANKS DIMENSIONS AND CAPACITY ACITY VOLUME (litres) B L H TYPE serb-mtp-en_b_td Note: Special versions of additional diesel fuel tank available on request. 2

21 EN 1284 DIESEL ENGINE PUMP TANKS COMBINATIONS AND POSITIONING PUMP CAPACITY (L) D.. GEN..D GEN..1D GEN..1D GEN..11D FHF32-12/D119 3 FHF32-12/D136 3 FHF32-16/D1 3 FHF32-16/D164 3 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD ON BOARD FHF32-2/D188 3 FHF32-2/D24 3 FHF4-12/D112 3 FHF4-12/D122 3 FHF4-12/D143 3 FHF4-16/D19 3 FHF4-16/D171 3 FHF4-2/D19 3 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD ON BOARD FHF4-2/D29 3 FHF4-2/D218 3 FHF4-2/D233 3 FHF4-2/D21 3 FHF-12/D119 3 FHF-12/D13 3 FHF-12/D139 3 FHF-16/D18 3 FHF-16/D174 3 FHF-2/D197 3 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD ON BOARD FHF-2/D29 3 FHF-2/D224 3 FHF-2/D237 6 FHF-2/D2 6 FHF6-12/D121 3 FHF6-12/D129 3 FHF6-12/D14 3 FHF6-16/D161 3 FHF6-16/D168 3 FHF6-16/D178 3 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD ON BOARD FHF6-2/D187 3 FHF6-2/D198 6 FHF6-2/D21 6 FHF6-2/D22 6 FHF6-2/D241 6 FHF6-2/D28 9 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF8-16/D163 3 FHF8-16/D173 6 FHF8-2/D189 6 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD ON BOARD FHF8-2/D27 6 FHF8-2/D22 9 FHF8-2/D238 9 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF8-2/D26 11 pos-serb-fhf1284-en_b_td 21

22 EN 1284 DIESEL ENGINE PUMP TANKS COMBINATIONS AND POSITIONING PUMP CAPACITY (L) D.. GEN..D GEN..1D GEN..11D FHF1-16/D1 3 FHF1-16/D16 6 FHF1-16/D18 6 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD FHF1-2/D168 6 FHF1-2/D192 6 FHF1-2/D23 9 FHF1-2/D213 9 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF1-2/D2 6 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD FHF1-2/D221 9 FHF1-2/D23 11 FHF1-2/D24 17 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF1-2/D FHF12-2/D18 6 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD FHF12-2/D26 9 FHF12-2/D FHF12-27/D FHF12-27/D FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF12-27/D23 24 FHF12-27/D pos-serb-fhf en_b_td 22

23 EN 1284 DIESEL ENGINE PUMP TANKS COMBINATIONS AND POSITIONING PUMP CAPACITY (L) D.. GEN..D GEN..1D GEN..1D GEN..11D SHF32-12/D121 3 SHF32-12/D136 3 SHF32-16/D1 3 SHF32-16/D168 3 SHF32-2/D188 3 WALL-MOUNTED SHF32-2/D24 3 SHF32-2/D222 3 SHF32-2/D242 3 SHF32-2/D26 3 SHF4-12/D112 3 SHF4-12/D126 3 SHF4-12/D143 3 SHF4-16/D19 3 SHF4-16/D171 3 SHF4-2/D19 3 WALL-MOUNTED SHF4-2/D29 3 SHF4-2/D218 3 SHF4-2/D233 3 SHF4-2/D21 3 SHF-12/D119 3 SHF-12/D13 3 SHF-12/D139 3 SHF-16/D18 3 SHF-16/D174 3 SHF-2/D197 3 WALL-MOUNTED SHF-2/D29 3 SHF-2/D224 3 SHF-2/D237 6 SHF-2/D2 6 SHF6-16/D119 3 SHF6-16/D129 3 SHF6-16/D137 3 SHF6-16/D168 3 SHF6-16/D177 3 WALL-MOUNTED SHF6-2/D192 3 SHF6-2/D23 6 SHF6-2/D21 6 SHF6-2/D24 6 WALL-MOUNTED ON BOARD ON BOARD ON BOARD WALL-MOUNTED ON BOARD ON BOARD ON BOARD WALL-MOUNTED ON BOARD ON BOARD ON BOARD WALL-MOUNTED ON BOARD ON BOARD ON BOARD SHF6-2/D2 9 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED SHF8-16/D169 3 SHF8-16/D177 3 SHF8-16/D186 6 WALL-MOUNTED WALL-MOUNTED ON BOARD ON BOARD ON BOARD SHF8-2/D198 6 SHF8-2/D21 6 SHF8-2/D226 9 SHF8-2/D237 9 SHF8-2/D22 11 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED SHF8-2/D27 17 pos-serb-shf1284-en_b_td 23

24 STARTING BATTERIES TERIES FOR DIESEL ENGINE PUMP EN 1284 COMBINATIONS AND SIZES TABLE OF DIESEL ENGINE PUMP FHF COMBINATIONS DIESEL BATTERY DIESEL BATTERY ENGINE PUMP TYPE ENGINE PUMP TYPE TYPE TYPE DFHFE.. A B C D E DFHFE.. A B C D E PUMP PUMP 32-12/D /D /D /D /D1 6-2/D /D /D /D /D /D24 6-2/D /D /D /D /D /D /D /D19 8-2/D /D /D22 4-2/D19 8-2/D /D29 8-2/D26 4-2/D /D1 4-2/D /D16 4-2/D /D18-12/D /D168-12/D13 1-2/D192-12/D /D23-16/D18 1-2/D213-16/D /D2-2/D /D221-2/D29 1-2/D23-2/D /D24-2/D /D267-2/D2 12-2/D /D /D /D /D /D /D /D /D /D /D /D /D FHF32-12_ab-en_a_tc 24

25 STARTING BATTERIES TERIES FOR DIESEL ENGINE PUMP EN 1284 TABLE OF DIESEL ENGINE PUMP SHF 32-8 COMBINATIONS DIESEL BATTERY ENGINE PUMP TYPE TYPE DSHFE.. A B C D E 32-12/D /D /D /D /D /D /D /D /D /D /D /D /D /D /D19 4-2/D29 4-2/D /D /D21-12/D119-12/D13-12/D139-16/D18-16/D174-2/D197-2/D29-2/D224-2/D237-2/D2 6-16/D /D /D /D /D /D /D23 6-2/D21 6-2/D24 6-2/D2 8-16/D /D /D /D /D21 8-2/D /D /D22 8-2/D27 PUMP 1284-SHF32-8_ab-en_a_tc 2

26 GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION Criteria for choosing fire-fighting sets The correct choice of a fire-fighting set must consider various factors, including the correct sizing of the performance levels required for the system, local regulations and legislation, and especially the installation conditions relative to the installation site and whether a suction lift or a positive suction head is involved. Choosing the type of water supply The type of water supply and, therefore, the type of booster set to select depends on the type of system involved and is chosen according to the risk analysis performed by the designer. There is no written rule for identifying the correct number of pumps to install. GEN booster sets are normally designed so that every service pump can satisfy the following requirements: 1% of rated capacity with one or two pumps installed (one in service and the other in reserve). If three pumps are installed, the capacity of the pump will be % of the total rated capacity and the third service pump will be considered as a reserve. In these cases, when superior or duplicated water supplies are involved, only one pump must be driven by an electric motor. This type of configuration is available on request. Suction conditions of the booster set The type of installation, suction lift or positive suction head, tends to affect (negatively or positively) the hydraulic performance of the pump. Remembering that EN1284 recommends against using suction lift installations, the following condition given by EN1284 must be satisfied in order to use the pump curve correctly: NPSHd NPSHr +1 [m] Where: NPSHd is defined available. NPSHr is defined requested from the pump. As the suction check condition must be made at the max. requested flow, there can be different performance levels always respecting the NPSHd condition. To select the booster set, consult the dedicated sections. Choice and selection. Hydraulic performance levels. Suction lift or positive suction head installation. Performance levels of booster sets: using the tables The tables showing the hydraulic performance levels of booster sets indicate the flow values according to the risk class for precalculated systems followed by the respective pressure value. This value does not refer to pump performance but is net of the pressure drop on the pump discharge line, to the discharge manifold flange. This field is shown in grey and the selection must be made here, where performance levels comply with the reference standard which considers the following conditions: Maximum water speed in the service pump discharge piping 6 m/sec. NPSHd NPSHr + 1 at the maximum flow required. Max. difference in level of water considered 3,2 m (for positive suction head). Suction pressure drops due to valves, piping, suction kit 1, m (limit value). The reference suction conditions are the severest and most extreme that can occur. The values taken in the fields that are not in grey indicate booster set performance levels in areas outside the limits of the standard and must not be used to choose the set. 26

27 GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION Method of selecting a fire-fighting booster set Referring to EN 1284, after identifying the risk classes of the activity to protect and performing the precalculation method, the flow and head values required for the fire-fighting system can be obtained. This data is used as follows: 1. Configuration of the booster set, choice of the number of service pumps and relative type of motor/engine (two pumps, one electric and the other driven by a diesel engine). 2. Installation conditions (e.g.. positive suction head), see performance levels for positive suction head installation. 3. Determination of service flow e.g.: 11 l/min risk class OH3. RISK CLASS TYPE RATED OH2n OH3n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4. Determining the head e.g.: 3 m. RISK CLASS TYPE RATED OH2n OH3n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 16,8 13,7 12,3 11,8 9, 6,2 3,7,9-12/3-12/D13 1 x 3 19,9 17, 16,1 1,8 13,6 1, 8,,3 2,3-12/4-12/D139 1 x 4 24,3 21,8 2,6 2,2 18,3 1,3 13,1 1, 7,7 6,2 4,6-16/ -16/D18 1 x, 31,8 29,3 27,7 27,3 24,8 21,1 18,2 1, 11,4 9, 7,6-16/7-16/D174 1 x 7, 39,8 36,6 3,2 34,8 32, 29,1 26, 23, 2,2 18, 16,7 12,7-2/11A -2/D197 1 x 11,6 4,6 43,4 42,8 39, 34,8 31,2 27,3 23,1 2,9 18,6-2/11-2/D29 1 x 11 8, 2,6, 49,9 46,7 42,1 38,6 34,7 3,4 28,1 2,7 2,7 As can be seen, the required flow value enters the operating area in accordance with the standard, and the value of the corresponding head enters the field in grey. From the example shown above, we can identify the booster set that satisfies the request. The model is pump -2/11 providing a head of 38,6 m. 27

28 GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - POSITIVE SUCTION HEAD INSTALLA ALLATION EN1284 recommends always installing pumps in suction lift conditions, where possible If this is not possible, the pumps can be installed in positive suction head conditions according to the following rules: The height of the minimum water level at the pump axis must not be greater than 3,2 m. A foot valve must be installed in the lowest point of the suction piping. If more than one pump is installed, the suction piping must not be interconnected. Normal Liv. normale level Max 3,2 m Liv. Min X Min. level X Fig. 1 positive suction head installation diagram In accordance with EN 1284 ( ), the suction piping, including all the valves and unions, must be designed to ensure that the NPSH available at the pump inlet exceeds the required NPSH by at least 1 m at the maximum required flow rate. NPSHd NPSHr + 1 When selecting the type of pump to use for the boosters sets, the installation conditions must be considered as these determine different pump performance levels. An example of how to choose and check of the installation conditions is shown below: considering the precalculation method, a suitable risk class for the system is identified, e.g.: OH3. For this risk class, the rated flow is 11 l/min (Qn), while the maximum requested flow is 13 l/min (Qm). Being in a positive suction head condition, the most difficult situation is considered, i.e.: the maximum difference in water level of 3,2 m, as indicated in the standard. Being aware of the rated flow 11 l/min and the pressure required for the system (e.g.: 3 m), the pump is selected according to the tables on page 44-4, making sure the performance rating lies inside the area shown in grey. The pump that satisfies the required work point is FHF-2/11. 28

29 GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - POSITIVE SUCTION HEAD INSTALLA ALLATION At this point, the installation conditions (positive suction head) must be checked at the maximum required flow. The following values are replaced in the known relation, NPSHd NPSHr + 1: NPSHr can be deduced from the table on page 4 which in this case is 4,6 m at the maximum requested flow. After replacing the value, the following will be true (water temperature around 1 C): NPSHd = 1,33 + (-3,2) - Hct Where 1,33 atmospheric pressure 3,2 geodetic difference in level Hct suction pressure drop ((valves, pipes, elbows..) The value of Hct considers the pressure drops of the suction kit, inclusive of vibration-proof joint, reduction cone and on-off valve (Hc), as well as the pressure drops relative to all the suction piping, foot valve, elbows, elbows, etc... The value of Hc at the maximum required flow of the selected pump can be found in the diagram on page 81. This value is,16 m. After entering it in the formula, we will have: Hct =,16 + X Where X is the pressure drop relative to all the suction piping Hence NPSHd NPSHr + 1. After replacing this, we will have: 1,33 + (-3,2) - Hct = 4,6 +1 1,33 + (-3,2),16 - X = 4,6 +1 which gives X = 1,37 m Maximum value of total drops to consider on the inlet piping in order to respect the conditions of the standard. Of course, this case was deliberately put in the worst suction conditions. The designer must check and set the values in an attempt to optimise suction conditions. 29

30 Checking performance of the set at rated flow. GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - POSITIVE SUCTION HEAD INSTALLA ALLATION The performance of the booster set must now be checked in the installation conditions of the example used up until now. Work point: Qn: 11 l/min H = 3 m The selected pump is FHF-2/11 Starting from the usual relation given by the standard, we will have: NPSHd NPSHr + 1 NPSHd = 1,33 + (-3,2) - Hct NPSHr can be deduced from the table on page 4 which in this case is 2,9 m at the rated flow. The value of Hct considers the pressure drops of the suction kit, inclusive of vibration-proof joint, reduction cone and on-off valve (Hc), as well as the pressure drops relative to all the suction piping, foot valve, elbows, elbows, etc... The value of Hc at the rated required flow of the selected pump can be found in the diagram on page 81. This value is,12 m. After entering it in the formula, we will have: Hct =,12 + X Where X is the pressure drop relative to all the suction piping Hence NPSHd NPSHr + 1. After replacing this, we will have: 1,33 + (-3,2) - Hct = 2,9 +1 1,33 + (-3,2),12 - X = 2,9 +1 which gives X = 3,11 m Value of the total drops to consider on the suction piping Taking the pressure value of the selected set, the value corresponds to 38,6 m at the rated flow. Therefore, the verification of the pressure values in the above suction conditions becomes: H = 38,6 -,12-3,11 = 3,4 m > 3 m which is the pressure required for the system The result satisfies the performance required for the system in the installation conditions of the example. 3

31 GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - SUCTION LIFT INSTALLA ALLATION Suction lift installation EN1284 recommends always installing pumps in suction lift conditions, where possible, according to the following rules: At least two thirds of the effective capacity of the suction tank must be above the level of the pump axis. The pump axis must not be more than 2 m above the minimum water level in the suction tank. Liv. Normal normale level 2/3 della of capacità effective effettiva capacity Max 2 m Liv. Min. Min level X Fig. 2 suction lift installation diagram In accordance with EN 1284 ( ), the suction piping, including all the valves and unions, must be designed to ensure that the NPSH available at the pump inlet exceeds the required NPSH by at least 1 m at the maximum required flow rate. NPSHd NPSHr + 1 When selecting the type of pump to use for the boosters sets, the installation conditions must be considered as these determine different pump performance levels. An example of how to choose and check of the installation conditions is shown below: considering the precalculation method, a suitable risk class for the system is identified, e.g.: OH3. For this risk class, the rated flow is 11 l/min (Qn), while the maximum requested flow is 13 l/min (Qm). Being in the suction lift condition, a neutral situation is used in order to consider the water level on the same horizontal plane as the pump, without benefiting from any positive suction head. 31

32 GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - SUCTION LIFT INSTALLA ALLATION Being aware of the rated flow 11 l/min and the pressure required for the system (e.g.: 3 m), the pump is selected according to the tables on page 44-4, making sure the performance rating lies inside the area shown in grey. The pump that satisfies the required work point is FHF-2/11. At this point, the installation conditions (suction lift) must be checked at the maximum required flow. The following values are replaced in the known relation, NPSHd NPSHr + 1: NPSHr can be deduced from the table on page 4 which in this case is 4,6 m at the maximum requested flow. After replacing the value, the following will be true (water temperature around 1 C): NPSHd = 1,33 + () - Hct Where 1,33 atmospheric pressure geodetic difference in level Hct suction pressure drop (valves, pipes, elbows...) The value of Hct considers the pressure drops of the suction kit, inclusive of vibration-proof joint, reduction cone and on-off valve (Hc), as well as the pressure drops relative to all the suction piping, foot valve, elbows, elbows, etc The value of Hc at the maximum required flow of the selected pump can be found in the diagram on page 87. This value is,32 m. After entering it in the formula, we will have: Hct =,32 + X Where X is the pressure drop relative to all the suction piping Hence NPSHd NPSHr + 1. After replacing this, we will have: 1,33 + () - Hct = 4,6 +1 1,33 + (),32 - X = 4,6 +1 which gives X = 4,41 m Maximum value of total drops to consider on the inlet piping in order to respect the conditions of the standard. Of course, the case in point was deliberately tested in neutral suction conditions that neither benefit nor optimise suction. The designer must check and set the values in an attempt to make suction conditions as efficient as possible. 32

33 GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - SUCTION LIFT INSTALLA ALLATION Checking performance of the selected set at rated flow. The performance of the booster set must now be checked in the installation conditions of the example used up until now. Work point: Qn 11 l/min H = 3 m The selected pump is FHF-2/11 Starting from the usual relation given by the standard, we will have: NPSHd NPSHr + 1 NPSHd = 1,33 + () - Hct NPSHr can be deduced from the table on page 4 which in this case is 2,9 m at the rated flow. The value of Hct considers the pressure drops of the suction kit, inclusive of vibration-proof joint, reduction cone and on-off valve (Hc), as well as the pressure drops relative to all the suction piping, foot valve, elbows, elbows, etc... The value of Hc at the rated required flow of the selected pump can be found in the diagram on page 87. This value is,22 m. After entering it in the formula, we will have: Hct =,22 + X Where X is the pressure drop relative to all the suction piping Hence NPSHd NPSHr + 1. After replacing this, we will have: 1,33 + () - Hct = 2,9 +1 1,33 + (),22 - X = 2,9 +1 which gives X = 6,21 m Value of the total drops to consider on the suction piping Taking the pressure value of the selected set, the value corresponds to 38,6 m at the rated flow. Therefore, the verification of the pressure values in the above suction conditions becomes: H = 38,6 -,22-6,21 = 32,17 m < 3 m which is the pressure required for the system. The value obtained, doesn t satisfy the performance necessary for the system, but as is evident, we have used deliberately a neutral installation condition that it doesn t give benefits to the suction. It results that installed the pump with positive suction of 3 m, we will have a pressure value of 3,17 m that it satisfied the relation. 33

34 34

35 GEN..D/FHF Series Fire-fighting booster sets EN 1284, high-efficiency electric pumps with PLM motors and series FHF horizontal centrifugal diesel engine pumps Hz 3

36 36

37 RANGE GEN..D/FHF RANGE The range of EN 1284 fire-fighting booster sets with diesel and electric service pumps and optional jockey pump to adapt to the specific needs of every application. D.. ENGINE PUMP Single fire-fighting centrifugal pump in horizontal design with cast iron casing, FHF series. Head up to 1 m. Flow up to 6 m 3 /h. GEN..D SERIES Fire-fighting sets with diesel engine centrifugal service pump, in horizontal design with cast iron casing, FHF series. Head up to 1 m. Flow up to 6 m 3 /h. GEN..1D SERIES Fire-fighting sets with diesel engine service pump and electric jockey pump. The centrifugal service pump has horizontal design and cast iron casing. FHF series. Head up to 1 m. Flow up to 6 m 3 /h. GEN..1D SERIES Fire-fighting sets with diesel engine service pump and electric jockey pump. The centrifugal service pump has horizontal design and cast iron casing. FHF series. Head up to 1 m. Flow up to 13 m 3 /h. GEN..11D SERIES Fire-fighting sets with diesel engine service pump, electric service pump and electric jockey pump. The centrifugal service pump has horizontal design and cast iron casing. FHF series. Head up to 1 m. Flow up to 13 m 3 /h. 37

38 GEN..D/FHF BOOSTER SETS SERIES HYDRAULIC PERFORMANCE TABLE AT Hz (JOCKEY PUMP) PUMP NOMINAL Q = DELIVERY TYPE POWER l/min m 3 /h 1,2 1,8 2,4 3 3,6 4,2 6 7,2 8 kw HP H = TOTAL HEAD METRES COLUMN OF WATER SV2 4,,7 42, 37, 34, 3, 26, 2, 1, SV2 6,7 1 64, 6, 1, 4, 38, 31, 22, SV2 9 1,1 1, 96, 84, 76, 68, 8, 46, 32, SV2 12 1, 2 128, 112, 12, 91, 77, 62, 44, SV2 14 2,2 3 1, 131, 119, 16, 9, 73, 2, SV2 1 2,2 3 16,2 14,3 128,2 114, 97,4 78,2,9 SV4 7 1,1 1, 7, 9, 6, 3, 1, 37, 26, 18, SV4 9 1, 2 9, 76, 73, 68, 6, 47, 33, 23, SV4 13 2, , 111, 1, 99, 9, 68, 48, 34, Performance in accordance with the ISO Annex A Standard. EN1284_pp_sv2-4-2p-en_b_th PUMP TYPE NOMINAL POWER l/min 1 12 Q = DELIVERY m 3 /h 6 7, kw HP H = TOTAL HEAD METRES COLUMN OF WATER SV8 2, , SV , , 2 4 SV8 7 4, 9, ,2 SV8 9 4, , Performance in accordance with the ISO Annex A Standard. EN1284_pp_sv8-2p-en_a_th 38

39 GEN..D/FHF 32-8 BOOSTER SETS SERIES SERVICE PUMP JOCKEY PUMP COMBINATIONS SERVICE PUMP JOCKEY PUMP ELECTRIC PUMP TYPE FHF.. PUMP 32-12/ /D / /D / /D / /D /3 32-2/D /4 32-2/D / /D /1 4-12/D / /D /3 4-16/D /4 4-16/D / 4-2/D19 4-2/7 4-2/D29 4-2/11A 4-2/D /11 4-2/D /1 4-2/D21-12/22-12/D119-12/3-12/D13-12/4-12/D139-16/ -16/D18-16/7-16/D174-2/11A -2/D197-2/11-2/D29-2/1-2/D224-2/18-2/D237-2/22-2/D2 6-12/4 6-12/D / 6-12/D /7 6-12/D /11A 6-16/D / /D /1 6-16/D /1 6-2/D /18 6-2/D /22 6-2/D21 6-2/22 6-2/D22 6-2/3 6-2/D /37 6-2/D /1 8-16/D / /D /22 8-2/D /3 8-2/D27 8-2/37 8-2/D22 8-2/4 8-2/D / 8-2/D26 SV2 4 SV2 6 SV2 9 SV2 12 SV2 14 SV2 1 SV4 7 SV4 9 SV4 13 SV8 SV8 6 SV8 7 SV FHF32-8_ap-en_a_tc 39

40 GEN..D/FHF 1-12 BOOSTER SETS SERIES SERVICE PUMP JOCKEY PUMP COMBINATIONS SERVICE PUMP JOCKEY PUMP ELECTRIC PUMP TYPE FHF.. PUMP SV / /D1 1-16/ /D /3 1-16/D18 1-2/18 1-2/D /3 1-2/D /37 1-2/D23 1-2/4 1-2/D /3 1-2/D2 1-2/4 1-2/D / 1-2/D23 1-2/7 1-2/D24 1-2/9 1-2/D /3 12-2/D /4 12-2/D / 12-2/D / /D / /D / /D / /D266 SV2 6 SV2 9 SV2 12 SV2 14 SV2 1 SV4 7 SV4 9 SV4 13 SV8 SV8 6 SV8 7 SV FHF1-12_ap-en_a_tc 4

41 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/FHF 32 BOOSTER SETS SERIES RISK CLASS TYPE RATED LHn FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 32-12/ /D119 1 x,7 16,9 1,6 14,1 12,1 1,9 9,6 8,1 6, / /D136 1 x 1,1 21,9 2, 19,1 17,2 16,1 14,9 13, 12,1 7,1, / /D1 1 x 1, 27,3 2,6 24, 21,8 2, 19, 17,4 1,6 9, 7, / /D164 1 x 2,2 34,7 33,1 31, 29,3 27,9 26, 24,9 23,2 17,3 1, 12,7 1,2 32-2/3 32-2/D188 1 x 3 44,2 41,3 39,3 36,8 3,3 33,7 32, 3,1 23,4 2,8 18, 1, 32-2/4 32-2/D24 1 x 4 4,4 1,7 49, 46,8 4,2 43, 41,7 39,7 33,2 3,8 28,2 2,6 2, Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-fhf32-2p-en_a_th LHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 32 BOOSTER SETS SERIES RISK CLASS TYPE RATED LHn FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 32-12/ /D119 1 x,7 16,9 1,6 14,1 12,1 1,9 9,6 8,1 6, / /D136 1 x 1,1 21,9 2, 19,1 17,2 16,1 14,9 13, 12,1 7,1, / /D1 1 x 1, 27,3 2,6 24, 21,8 2, 19, 17,4 1,6 9, 7, / /D164 1 x 2,2 34,7 33,1 31, 29,3 27,9 26, 24,9 23,2 17,3 1, 12,7 1,2 32-2/3 32-2/D188 1 x 3 44,2 41,3 39,3 36,8 3,3 33,7 32, 3,1 23,4 2,8 18, 1, 32-2/4 32-2/D24 1 x 4 4,4 1,7 49, 46,8 4,2 43, 41,7 39,7 33,2 3,8 28,2 2,6 2, Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-fhf32-2p-en_a_th LHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. NPSH REQUIRED FOR PUMP SERIES FHF 32 RISK CLASS TYPE RATED LHn FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 32-12/ /D119 1 x,7 1,6 1,6 1,7 1,8 2, 2, / /D136 1 x 1,1 1,6 1,6 1,7 1,8 2, 2,2 2,9 3,4 4, 32-16/ /D1 1 x 1, 2,2 2,4 2, 2,7 2,8 3, 3,6 3,9 4, / /D164 1 x 2,2 2,2 2,4 2, 2,7 2,8 3, 3,6 3,9 4,4,9 32-2/3 32-2/D188 1 x 3 2,7 2,9 3,1 3,3 3, 3,8 4,3 4,6 4,9, 32-2/4 32-2/D24 1 x 4 2,7 2,9 3,1 3,3 3, 3,8 4,3 4,6 4,9, 6,2 The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-fhf32-2p_NPSHr-en_a_th LHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Check that NPSHd NPSHr+1m is satisfied 41

42 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/FHF 4 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH1n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4-12/ /D112 1 x 1,1 13,9 11,3 1, 9,3 3,4,7 4-12/1 4-12/D122 1 x 1, 18, 1,3 14, 13,3 7,4 4,7 4-12/ /D143 1 x 2,2 2,3 21,8 2, 19,8 14, 11,4 6,4, 3,6,6 4-16/3 4-16/D19 1 x 3 31,6 28,1 26,8 26, 19, 16, 1,8 9,2 7,6 4-16/4 4-16/D171 1 x 4 38,3 3,1 33,7 32,9 26, 23,6 18,1 16, 1, 11,7 4-2/ 4-2/D19 1 x, 46,4 42,7 41,2 4,4 33,1 29,7 23,3 21, 19,6 4-2/7 4-2/D29 1 x 7, 7, 3,1 1,6,7 43,8 4,7 34,8 33,2 31, 28, 4-2/11A 4-2/D218 1 x 11 63,6 7,8 6,2,2 47,8 44, 38,2 36, 34,8 31,1 4-2/11 4-2/D233 1 x 11 71,7 66, 64,3 63,4,7 2,3 4,8 44, 42,1 38,3 4-2/1 4-2/D21 1 x 1 8, 78,6 76,9 76, 68,4 6, 8,6 6,8, 1,1 42,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-fhf4-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 4 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH1n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4-12/ /D112 1 x 1,1 13,9 11,3 1, 9,3 3,4,7 4-12/1 4-12/D122 1 x 1, 18, 1,3 14, 13,3 7,4 4,7 4-12/ /D143 1 x 2,2 2,3 21,8 2, 19,8 14, 11,4 6,4, 3,6,6 4-16/3 4-16/D19 1 x 3 31,6 28,1 26,8 26, 19, 16, 1,8 9,2 7,6 4-16/4 4-16/D171 1 x 4 38,3 3,1 33,7 32,9 26, 23,6 18,1 16, 1, 11,7 4-2/ 4-2/D19 1 x, 46,4 42,7 41,2 4,4 33,1 29,7 23,3 21, 19,6 4-2/7 4-2/D29 1 x 7, 7, 3,1 1,6,7 43,8 4,7 34,8 33,2 31, 28, 4-2/11A 4-2/D218 1 x 11 63,6 7,8 6,2,2 47,8 44, 38,2 36, 34,8 31,1 4-2/11 4-2/D233 1 x 11 71,7 66, 64,3 63,4,7 2,3 4,8 44, 42,1 38,3 4-2/1 4-2/D21 1 x 1 8, 78,6 76,9 76, 68,4 6, 8,6 6,8, 1,1 42,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-fhf4-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

43 NPSH REQUIRED FOR PUMP SERIES FHF 4 RISK CLASS TYPE RATED OH1n OH1m FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 4-12/ /D112 1 x 1,1 1,8 1,9 1,9 2,4 2,7 4-12/1 4-12/D122 1 x 1, 1,8 1,9 1,9 2,4 2,7 3,7 4-12/ /D143 1 x 2,2 1,8 1,9 1,9 2,4 2,7 3,7 4,1 4,6 6,3 4-16/3 4-16/D19 1 x 3 1,9 1,9 1,9 2,4 2,9 4,1 4,, 4-16/4 4-16/D171 1 x 4 1,9 1,9 1,9 2,4 2,9 4,1 4,, 6,2 4-2/ 4-2/D19 1 x, 2, 2,1 2,2 2,9 3,4 4, 4,9,3 4-2/7 4-2/D29 1 x 7, 2, 2,1 2,2 2,9 3,4 4, 4,9,3 6,3 4-2/11A 4-2/D218 1 x 11 1, 1,1 1,2 1,6 1,7 2,1 2,2 2,3 2,6 4-2/11 4-2/D233 1 x 11 1, 1,1 1,2 1,6 1,7 2,1 2,2 2,3 2,6 4-2/1 4-2/D21 1 x 1 1, 1,1 1,2 1,6 1,7 2,1 2,2 2,3 2,6 3, The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = class of risk value referred to the required rated and maximum capacity (Tab.6 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-fhf4-2p_NPSHr-en_a_th 43

44 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/FHF BOOSTER SETS SERIES RISK CLASS TYPE RATED OH2n OH3n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 16,8 13,7 12,3 11,8 9, 6,2 3,7,9-12/3-12/D13 1 x 3 19,9 17, 16,1 1,8 13,6 1, 8,,3 2,3-12/4-12/D139 1 x 4 24,3 21,8 2,6 2,2 18,3 1,3 13,1 1, 7,7 6,2 4,6-16/ -16/D18 1 x, 31,8 29,3 27,7 27,3 24,8 21,1 18,2 1, 11,4 9, 7,6-16/7-16/D174 1 x 7, 39,8 36,6 3,2 34,8 32, 29,1 26, 23, 2,2 18, 16,7 12,7-2/11A -2/D197 1 x 11,6 4,6 43,4 42,8 39, 34,8 31,2 27,3 23,1 2,9 18,6-2/11-2/D29 1 x 11 8, 2,6, 49,9 46,7 42,1 38,6 34,7 3,4 28,1 2,7 2,7-2/1-2/D224 1 x 1 68,1 62,8 6,9 6,4 7,3 2,6 48,8 44,4 39,4 36,7 33,8-2/18-2/D237 1 x 18, 76, 71,7 7, 69, 66,6 62,3 8,8 4,7, 47,4 44,7 38,6-2/22-2/D2 1 x 22 86, 81,2 79, 79, 76,1 71,7 68,1 64, 9,4 6,8 4,1 48,1 41,4 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-fhf-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF BOOSTER SETS SERIES RISK CLASS TYPE RATED OH2n OH3n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 16,8 13,7 12,3 11,8 9, 6,2 3,7,9-12/3-12/D13 1 x 3 19,9 17, 16,1 1,8 13,6 1, 8,,3 2,3-12/4-12/D139 1 x 4 24,3 21,8 2,6 2,2 18,3 1,3 13,1 1, 7,7 6,2 4,6-16/ -16/D18 1 x, 31,8 29,3 27,7 27,3 24,8 21,1 18,2 1, 11,4 9, 7,6-16/7-16/D174 1 x 7, 39,8 36,6 3,2 34,8 32, 29,1 26, 23, 2,2 18, 16,7 12,7-2/11A -2/D197 1 x 11,6 4,6 43,4 42,8 39, 34,8 31,2 27,3 23,1 2,9 18,6-2/11-2/D29 1 x 11 8, 2,6, 49,9 46,7 42,1 38,6 34,7 3,4 28,1 2,7 2,7-2/1-2/D224 1 x 1 68,1 62,8 6,9 6,4 7,3 2,6 48,8 44,4 39,4 36,7 33,8-2/18-2/D237 1 x 18, 76, 71,7 7, 69, 66,6 62,3 8,8 4,7, 47,4 44,7 38,6-2/22-2/D2 1 x 22 86, 81,3 79, 79, 76,1 71,7 68,2 64,1 9, 6,9 4,2 48,2 41,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-fhf-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

45 NPSH REQUIRED FOR PUMP SERIES FHF RISK CLASS TYPE RATED OH2n OH2m OH3n OH3m FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] -12/22-12/D119 1 x 2,2 2,1 2,3 2,3 2,6 3,1 3, 3,9-12/3-12/D13 1 x 3 2,1 2,3 2,3 2,6 3,1 3, 3,9 4,4-12/4-12/D139 1 x 4 2,1 2,3 2,3 2,6 3,1 3, 3,9 4,4 4,7, -16/ -16/D18 1 x, 1,9 2,1 2,2 2, 2,9 3,2 3,6 4,2 4,6,1-16/7-16/D174 1 x 7, 1,9 2,1 2,2 2, 2,9 3,2 3,6 4,2 4,6,1 6, -2/11A -2/D197 1 x 11 1,8 1,9 2, 2,2 2,6 2,9 3,4 4,1 4,6,1-2/11-2/D29 1 x 11 1,8 1,9 2, 2,2 2,6 2,9 3,4 4,1 4,6,1 6,7-2/1-2/D224 1 x 1 1, 1,7 1,7 2, 2,4 2,7 3,1 3,6 3,9 4,2-2/18-2/D237 1 x 18, 1, 1,7 1,7 2, 2,4 2,7 3,1 3,6 3,9 4,2,1-2/22-2/D2 1 x 22 1, 1,7 1,7 2, 2,4 2,7 3,1 3,6 3,9 4,2,1 6,4 The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = class of risk value referred to the required rated and maximum capacity (Tab.6 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-fhf-2p_NPSHr-en_a_th 4

46 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/FHF 6 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH3n OH4n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 6-12/4 6-12/D121 1 x 4 19,1 1,6 14,6 13, 12,3 1,9 8,7 7,9 6,2 6-12/ 6-12/D129 1 x, 22,7 19,6 18,8 17,8 16,7 1, 13, 12,7 11,2,7 6-12/7 6-12/D14 1 x 7, 27,1 24,3 23, 22,7 21,7 2,7 18,9 18,2 16,8 12, 8,1 6-16/11A 6-16/D161 1 x 11 32,7 29,2 28,3 27,2 26, 23,9 23,2 21,6 1,9 11, 9, 6-16/ /D168 1 x 11 3,9 32, 31, 3, 29,4 27,4 26,7 2,2 19,8 1,6 13,3 6-16/1 6-16/D178 1 x 1 41,9 38,9 38,1 37,1 36,1 34,2 33,6 32,2 27,2 23,2 21,1 16,3 6-2/1 6-2/D187 1 x 1 4,2 43,4 42,3 41,1 39,7 37,3 36,4 34,6 28,4 23,8 21,3 6-2/18 6-2/D198 1 x 18, 1,6,2 49,2 48,2 47, 44,9 44,1 42,4 36, 31,8 29,2 6-2/22 6-2/D21 1 x 22 9,1 7,2 6,3,3 4,2 2,1 1,4 49,8 44,1 39,6 37,1 31,6 6-2/22 6-2/D22 1 x 22 62,8 6,6 9,4 8, 6,4 3, 2,,2 42,1 3,7 32,1 6-2/3 6-2/D241 1 x 3 76,4 7, 73,9 72,6 71,1 68, 67, 6,4 7,8 1,6 48,2 4,6 6-2/37 6-2/D28 1 x 37 9,8 89,9 89, 88, 86,7 84, 83,7 81,8 74,8 68,8 6,4 7,7 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-fhf6-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 6 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH3n OH4n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 6-12/4 6-12/D121 1 x 4 19,1 1,6 14,6 13, 12,3 1,9 8,7 7,9 6,2 6-12/ 6-12/D129 1 x, 22,7 19,6 18,8 17,8 16,7 1, 13, 12,7 11,2,7 6-12/7 6-12/D14 1 x 7, 27,1 24,3 23, 22,7 21,7 2,7 18,9 18,2 16,8 12, 8,1 6-16/11A 6-16/D161 1 x 11 32,7 29,2 28,3 27,2 26, 23,9 23,2 21,6 1,9 11, 9, 6-16/ /D168 1 x 11 3,9 32, 31, 3, 29,4 27,4 26,7 2,2 19,8 1,6 13,3 6-16/1 6-16/D178 1 x 1 41,9 38,9 38,1 37,1 36,1 34,2 33,6 32,2 27,2 23,2 21,1 16,3 6-2/1 6-2/D187 1 x 1 4,2 43,4 42,3 41,1 39,7 37,3 36,4 34,6 28,4 23,8 21,3 6-2/18 6-2/D198 1 x 18, 1,6,2 49,2 48,2 47, 44,9 44,1 42,4 36, 31,8 29,2 6-2/22 6-2/D21 1 x 22 9,1 7,2 6,3,3 4,2 2,1 1,4 49,8 44,1 39,6 37,1 31,6 6-2/22 6-2/D22 1 x 22 62,8 6,6 9,4 8, 6,4 3, 2,,2 42,1 3,7 32,1 6-2/3 6-2/D241 1 x 3 76,4 7, 73,9 72,6 71,1 68, 67, 6,4 7,8 1,6 48,2 4,6 6-2/37 6-2/D28 1 x 37 9,8 89,9 89, 88, 86,7 84, 83,7 81,8 74,8 68,8 6,4 7,7 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-fhf6-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

47 NPSH REQUIRED FOR PUMP SERIES FHF 6 RISK CLASS TYPE RATED OH3n OH3m OH4n OH4m FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 6-12/4 6-12/D121 1 x 4 1, 1,2 1,3 1,6 1,9 2,4 2,6 3,1 6-12/ 6-12/D129 1 x, 1, 1,2 1,3 1,6 1,9 2,4 2,6 3,1,1 6-12/7 6-12/D14 1 x 7, 1, 1,2 1,3 1,6 1,9 2,4 2,6 3,1,1 7, 6-16/11A 6-16/D161 1 x 11 2,4 2,4 2, 2,6 2,9 2,9 3,2 4,2,3 6, 6-16/ /D168 1 x 11 2,3 2,4 2, 2,7 2,8 2,9 3,1 3,7 4,4 4,9 6-16/1 6-16/D178 1 x 1 2,3 2,4 2, 2,7 2,8 2,9 3,1 3,7 4,4 4,9 6,6 6-2/1 6-2/D187 1 x 1 1,8 1,9 2, 2,1 2,3 2,4 2,6 3,4 4,,3 6-2/18 6-2/D198 1 x 18, 1,8 1,9 2, 2,1 2,3 2,4 2,6 3,4 4,3 4,9 6-2/22 6-2/D21 1 x 22 1,8 1,9 2, 2,1 2,3 2,4 2,6 3,4 4,3 4,9 6,6 6-2/22 6-2/D22 1 x 22 1,7 2, 2,2 2, 2,9 3,1 3,4 4,3,,4 6-2/3 6-2/D241 1 x 3 1,7 2, 2,2 2, 2,9 3,1 3,4 4,3,,4 6,2 6-2/37 6-2/D28 1 x 37 1,7 2, 2,2 2, 2,9 3,1 3,4 4,3,,4 6,2 The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-fhf6-2p_NPSHr-en_a_th OHn, OHm = class of risk value referred to the required rated and maximum capacity (Tab.6 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 47

48 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/FHF 8 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH4n HH1n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 8-16/1 8-16/D163 1 x 1 32,9 3,2 29,1 27,8 2,4 24,9 23,8 22,7 18,8 9,4 4,4 8-16/ /D173 1 x 18, 39, 3,6 34, 33,4 31,2 3,7 29,7 28,6 2,1 16,2 11,3 9, 8, 8-2/22 8-2/D189 1 x 22 48, 44,7 43,4 41,8 39, 38,3 37, 3,6 3,9 19,2 12,8 8-2/3 8-2/D27 1 x 3 9,9 6,9,8 4,4 1,9 1,3,1 48,9 44,7 34,2 28, 26,4 2,3 8-2/37 8-2/D22 1 x 37 7,8 67,3 6,8 63,9 6,4 9,6 7,9 6,1,1 34,7 26,1 8-2/4 8-2/D238 1 x 4 8, 78, 76, 74,8 71, 7,8 69,2 67,6 62, 47, 39,6 36, 8-2/ 8-2/D26 1 x 88,9 89,9 88,8 87, 84,8 84,2 82,9 81, 76,7 64, 6,7 4, 2,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-fhf8-2p-en_a_th OHn, HHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1, Tab.7 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 8 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH4n HH1n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 8-16/1 8-16/D163 1 x 1 32,9 3,2 29,1 27,8 2,4 24,9 23,8 22,7 18,8 9,4 4,4 8-16/ /D173 1 x 18, 39, 3,6 34, 33,4 31,2 3,7 29,7 28,6 2,1 16,2 11,3 9, 8, 8-2/22 8-2/D189 1 x 22 48, 44,7 43,4 41,8 39, 38,3 37, 3,6 3,9 19,2 12,8 8-2/3 8-2/D27 1 x 3 9,9 6,9,8 4,4 1,9 1,3,1 48,9 44,7 34,2 28, 26,4 2,3 8-2/37 8-2/D22 1 x 37 7,8 67,3 6,8 63,9 6,4 9,6 7,9 6,1,1 34,7 26,1 8-2/4 8-2/D238 1 x 4 8, 78, 76, 74,8 71, 7,8 69,2 67,6 62, 47, 39,6 36, 8-2/ 8-2/D26 1 x 88,9 89,9 88,8 87, 84,8 84,2 82,9 81, 76,7 64, 6,7 4, 2,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-fhf8-2p-en_a_th OHn, HHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1, Tab.7 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

49 NPSH REQUIRED FOR PUMP SERIES FHF 8 RISK CLASS TYPE RATED OH4n OH4m HH1n HH1m FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 8-16/1 8-16/D163 1 x 1 3,7 3,8 3,9 4, 4,1 4,2 4,2 4,,4 6,2 8-16/ /D173 1 x 18, 3,7 3,8 3,9 4, 4,1 4,2 4,2 4,,4 6,2 6, 6,8 8-2/22 8-2/D189 1 x 22 2,8 3, 3,1 3,3 3,4 3, 3,6 3,9,1 6,3 8-2/3 8-2/D27 1 x 3 2,8 3, 3,1 3,3 3,4 3, 3,6 3,9,1 6,3 6,9 7,3 8-2/37 8-2/D22 1 x 37 3, 3,1 3,3 3,6 3,6 3,8 3,9 4,4 6, 7,4 8-2/4 8-2/D238 1 x 4 2,4 2,6 2,7 3, 3,1 3,2 3,3 3,8 4,9,,7 8-2/ 8-2/D26 1 x 2,4 2,6 2,7 3, 3,1 3,2 3,3 3,8 4,9,,7,8 The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-fhf8-2p_NPSHr-en_a_th OHn, OHm, HHn, HHm = class of risk value referred to the required rated and maximum capacity (Tab.6 para 7.3.1, Tab.7 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 49

50 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/FHF 1 BOOSTER SETS SERIES RISK CLASS TYPE RATED HH1n HH2n HH3n HH4n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 1-16/ /D1 1 x 18, 26,7 26, 2,6 2,2 22,9 19,9 19, 18, 13,9 11,8 1,2 9,6 3, 1,8 1-16/ /D16 1 x 22 33, 32,2 31,7 31,2 28,7 2,3 24,4 23,3 18,8 16,6 14,8 14,2 7,6,9 4,2 2,2 1-16/3 1-16/D18 1 x 3 42,3 41,2 4,8 4,3 37,8 34,6 33,6 32, 28,2 26, 24,2 23,6 16,9 1,1 13, 11,4,3 1-2/18 1-2/D168 1 x 18, 36,3 33, 32,7 28,6 23, 22, 2,3 13, 1,1 7,4 6,4 1-2/3 1-2/D192 1 x 3 49, 47, 46,9 43,7 39, 38,3 36,8 31, 28, 2, 24,7 1, 12,9 1-2/37 1-2/D23 1 x 37 6, 4,6 4, 1, 46,9 4,8 44,4 38,7 3,8 33,4 32,6 23,7 21,2 18,9 16, 1-2/4 1-2/D213 1 x 4 61, 6, 9, 7,1 3,6 2,6 1,4 46,3 43,7 41, 4,7 32,3 29,9 27,7 24,8 1-2/3 1-2/D2 1 x 3 4,6 2,1 47,7 41,8 4, 37,9 29,3 24,8 21,2 19,9,9 1-2/4 1-2/D221 1 x 4 68,8 66,9 63, 8,7 7,2,4 48,1 44,2 41, 39,9 27,2 23,6 2,3 1,9 1-2/ 1-2/D23 1 x 78, 76,9 74, 69,8 68, 66,9 6,2 6,6 3,6 2,6 4,6 37,2 34, 29,8 RISK CLASS TYPE RATED HH4n HHn HH6n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 1-2/7 1-2/D24 1 x 7 91,7 9, 86,9 7,9 71,7 66,1 63,7 62,1 8,7 2,9 49,3 38,3 29,3 28, 1-2/9 1-2/D267 1 x 9 12,9 11,6 98,2 87, 83,4 77,9 7,6 74, 7,7 64,9 61,3, 41, 4,2 38, 32, 31,1 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-fhf1-2p-en_a_th HHn = class of risk value referred to the required rated capacity (Tab.7 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 1 BOOSTER SETS SERIES RISK CLASS TYPE RATED HH1n HH2n HH3n HH4n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 1-16/ /D1 1 x 18, 26,7 26,8 26,6 26,4 2, 23,1 22,6 21,9 19,3 18, 16,9 16,6 12,6 11, 1-16/ /D16 1 x 22 33, 33, 32,7 32,4 3,8 28,6 28, 27,2 24,3 22,8 21,6 21,1 16,8 1,6 14, 13,1 1-16/3 1-16/D18 1 x 3 42,3 42, 41,8 41, 39,9 37,8 37,2 36, 33,6 32,1 3,9 3, 26,1 24,9 23,7 22,3 18,2 1-2/18 1-2/D168 1 x 18, 36,3 34, 33,9 3,7 26,7 2,6 24,2 18,9 16,2 14,1 13,4 1-2/3 1-2/D192 1 x 3 49, 48, 48,1 4,8 42,8 41,9 4,8 36,4 34,1 32,3 31,6 24,6 22,6 1-2/37 1-2/D23 1 x 37 6,,,2 3,1,2 49,3 48,3 44,1 41,9 4,2 39,6 32,8 3,9 29,2 26,9 1-2/4 1-2/D213 1 x 4 61, 61, 6,7 9,2 6,9 6,2,3 1,7 49,8 48,2 47,7 41,4 39,6 37,9 3,8 1-2/3 1-2/D2 1 x 3 4,6 3,3 49,8 4, 43, 41,8 34,7 3,9 27,9 26,8 1, 1-2/4 1-2/D221 1 x 4 68,8 68,1 6,6 61,9 6,8 9,4 3,,4 47,7 46,8 36,3 33,4 3, 26,9 1-2/ 1-2/D23 1 x 78, 78,1 76,2 73, 72, 7,8 6,6 62,8 6,4 9, 49,7 46,9 44,2 4,7 RISK CLASS TYPE RATED HH4n HHn HH6n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 1-2/7 1-2/D24 1 x 7 91,7 91,7 89,4 81,3 78,1 73,7 71,8 7,6 67,9 63,2 6,2 1,3 43,8 42,8 1-2/9 1-2/D267 1 x 9 12,9 12,8 1,6 92,9 89,8 8, 83,7 82, 79,8 7,2 72,3 63,4 6, 4,9 3,1 48,1 47,3 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-fhf1-2p-en_a_th HHn = class of risk value referred to the required rated capacity (Tab.7 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284.

51 NPSH REQUIRED FOR PUMP SERIES FHF 1 RISK CLASS TYPE RATED HH1n HH2n HH3n HH1m HH4n HH2m HH3m HH4m FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw NPSHr [METRES COLUMN OF WATER] 1-16/ /D1 1 x 18, 6,3 6,4 6,6 7,3 8, 8,2 8,4 9,2 9, 9,8 9,9 11, 11,4 1-16/ /D16 1 x 22,,2,4 6,2 6,9 7, 7,2 7,9 8,3 8, 8,6 9,6 9,9 1,3 1,7 1-16/3 1-16/D18 1 x 3,,2,4 6,2 6,9 7, 7,2 7,9 8,3 8, 8,6 9,6 9,9 1,3 1,7 12,8 1-2/18 1-2/D168 1 x 18, 4,2 4,2 4,6,6 6, 6, 9,2 11,1 12,8 13, 1-2/3 1-2/D192 1 x 3 3,1 3,1 3,3 3, 3,6 3,7 4,2 4,6 4,9,1 7, 7,7 1-2/37 1-2/D23 1 x 37 3,1 3,1 3,3 3, 3,6 3,7 4,2 4,6 4,9,1 7, 7,7 8,4 9, 1-2/4 1-2/D213 1 x 4 3,1 3,1 3,3 3, 3,6 3,7 4,2 4,6 4,9,1 7, 7,7 8,4 9, 1-2/3 1-2/D2 1 x 3 4,7,,3,4,4,7,8,9 6, 6,3 1-2/4 1-2/D221 1 x 4 4,6 4,7 4,7 4,8 4,8 4,8 4,9 4,9 4,9,1,2,2,3 1-2/ 1-2/D23 1 x 4,6 4,7 4,7 4,8 4,8 4,8 4,9 4,9 4,9,1,2,2,3 RISK CLASS TYPE RATED HH4n HHn HH6n HH4m HHm HH6m FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw NPSHr [METRES COLUMN OF WATER] 1-2/7 1-2/D24 1 x 7 4,6 4,7 4,8 4,9,,,,1,2,3,8 6,6 6,7 1-2/9 1-2/D267 1 x 9 4,6 4,7 4,8 4,9,,,,1,2,3,8 6,6 6,7 6,9 7,8 7,9 The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-fhf1-2p_NPSHr-en_a_th HHn, HHm = class of risk value referred to the required rated and maximum capacity (Tab.7 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1

52 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/FHF 12 BOOSTER SETS SERIES RISK CLASS TYPE RATED HH6n HH7n HH8n HH9n HH1n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 12-2/3 12-2/D18 1 x 3 32,8 29,8 28,4 19,8 19,6 1,8 14,4 12,6 11,2 1,9 7,6 12-2/4 12-2/D26 1 x 4 47,2 44,8 43, 34,8 34,6 3,3 28,6 26,4 24, 24,1 19,7 16,6 13,9 12,1 12-2/ 12-2/D216 1 x 7,4,1 4, 4,6 4,4 41, 39,3 36,8 34,8 34,3 29,3 2,6 22,3 2, 17,4 14, / /D224 1 x 7 6,1 63,7 6,,8 1, 49,8 47,3 4,3 44,8 39,8 36,1 32,7 3, 27,9 24,6 22, / /D237 1 x 9 7,3 73,6 67, 66,8 62,8 61,1 8,8 6,8 6,3 1,2 47,4 43,8 41,4 38, 34,8 32,2 27, 12-27/ /D23 1 x 11 88,2 8,4 79,2 79, 7,1 73, 71,2 69,2 68,8 63, 9,,7 3, 49,9 4,8 42,8 37,6 33, / /D266 1 x , 94,8 88,6 88,4 84,7 83,2 81,1 79,2 78,8 74, 7,3 66,8 64, 61,7 8,,4,7 46,8 4, Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. HHn = class of risk value referred to the required rated capacity (Tab.7 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN _1pg-sp-fhf12-2p-en_a_th HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 12 BOOSTER SETS SERIES RISK CLASS TYPE RATED HH6n HH7n HH8n HH9n HH1n FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 12-2/3 12-2/D18 1 x 3 32,8 3,3 29,1 22,2 22, 19,1 18, 16,6 1,6 1,3 13, 12-2/4 12-2/D26 1 x 4 47,2 4,3 44,2 37,1 37, 33, 32,2 3,4 28,9 28,6 2,2 22,7 2,6 19,2 12-2/ 12-2/D216 1 x 7,4,6 4,7 48, 47,8 44,2 42,8 4,8 39,2 38,8 34,7 31,7 29, 27,1 2, 22, / /D224 1 x 7 6,1 64,4 8,4 8,2 4,7 3,3 1,3 49,7 49,3 4,2 42,2 39, 37,6 3, 32,8 3, / /D237 1 x 9 7,3 74,4 69,3 69,2 66, 64,7 62,8 61,2 6,8 6,6 3,, 48, 46,1 43, 4,8 36, / /D23 1 x 11 88,2 86,2 81, 81,4 78,4 77,1 7,2 73,6 73,2 68,9 6,6 62,4 6,1 7, 4, 1, 47, 43, / /D266 1 x , 9, 9,9 9,8 88, 86,8 8,1 83,6 83,3 79,4 76,4 73, 71,6 69,3 66,2 64, 6,1 6,8 1,4 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. HHn = class of risk value referred to the required rated capacity (Tab.7 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN _1pg-st-fhf12-2p-en_a_th NPSH REQUIRED FOR PUMP SERIES FHF 12 RISK CLASS TYPE RATED HH6n HH7n HH8n HH9n HH1n HH6m HH7m HH8m HH9m HH1m FHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 12-2/3 12-2/D18 1 x 3 6, 6,8 8, 8, 9,1 9,3 9,6 9,9 9,9 1,4 12-2/4 12-2/D26 1 x 4 6,1 6,2 7,1 7,1 7,6 7,7 8, 8,3 8,3 8,9 9, 1, 1,4 12-2/ 12-2/D216 1 x 6,1 6,2 7,1 7,1 7,6 7,7 8, 8,3 8,3 8,9 9, 1, 1,4 1,8 11, 12-27/ /D224 1 x 7 7,8 8,3 8,3 8, 8,6 8,7 8,8 8,9 9,3 9,7 1,1 1, 11,1 11,9 12, / /D237 1 x 9 6, 6,9 6,9 7,2 7,3 7, 7,7 7,7 8,1 8,4 8,8 9, 9,4 9,9 1,4 11, / /D23 1 x 11 6, 6,9 6,9 7,2 7,3 7, 7,7 7,7 8,1 8,4 8,8 9, 9,4 9,9 1,4 11,4 12, 12-27/ /D266 1 x 132 6, 6,9 6,9 7,2 7,3 7, 7,7 7,7 8,1 8,4 8,8 9, 9,4 9,9 1,4 11,4 12, 14,8 The declared NPSH values were obtained in the laboratory and refer to a single service pump HHn, HHm = class of risk value referred to the required rated and maximum capacity (Tab.7 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-fhf12-2p_NPSHr-en_a_th 2

53 GEN..D/FHF 1-12 BOOSTER SETS ELECTRICAL DATA A TABLE AT Hz SERVICE PUMP ELECTRIC JOCKEY PUMP CURRENT (*) ABSORBED SET 3 X 4 V 1 x 23V 3x4 TYPE NOMINAL 1x23V 3x4V FHF.. POWER ELECTRIC Pn In TYPE Pn In In GEN..D GEN..1D GEN..1D GEN..11D PUMP PUMP kw A kw A A A A A A 32-12/ /D119,7 2,2 SV26,7, 2,2 3 8,1, 7, 32-12/ /D136 1,1 2,61 SV26,7, 2,2 3 8,1,6 7, / /D1 1, 3,4 SV26,7, 2,2 3 8,1 6, 8, 32-16/ /D164 2,2,3 SV26,7, 2,2 3 8,1 8, 1,1 32-2/3 32-2/D188 3,77 SV26,7, 2,2 3 8,1 8,8 1,8 32-2/4 32-2/D24 4 7,9 SV29 1,1 6,82 2,61 3 9,8 1,6 13,2 4-12/ /D112 1,1 2,61 SV26,7, 2,2 3 8,1,6 7,6 4-12/1 4-12/D122 1, 3,4 SV26,7, 2,2 3 8,1 6, 8, 4-12/ /D143 2,2,3 SV26,7, 2,2 3 8,1 8, 1,1 4-16/3 4-16/D19 3,77 SV26,7, 2,2 3 8,1 8,8 1,8 4-16/4 4-16/D ,9 SV26,7, 2,2 3 8,1 1,6 12,6 4-2/ 4-2/D19, 1,7 SV26,7, 2,2 3 8,1 13,7 1,7 4-2/7 4-2/D29 7, 13,9 SV29 1,1 6,82 2,61 3 9,8 16,9 19, 4-2/11A 4-2/D ,8 SV29 1,1 6,82 2,61 3 9,8 22,8 2,4 4-2/11 4-2/D ,8 SV29 1,1 6,82 2,61 3 9,8 22,8 2,4 4-2/1 4-2/D ,2 SV29 1,1 6,82 2,61 3 9,8 29,2 31,8-12/22-12/D119 2,2 7,9 SV26,7, 2,2 3 8,1 1,6 12,6-12/3-12/D13 3,77 SV26,7, 2,2 3 8,1 8,8 1,8-12/4-12/D ,9 SV26,7, 2,2 3 8,1 1,6 12,6-16/ -16/D18, 1,7 SV26,7, 2,2 3 8,1 13,7 1,7-16/7-16/D174 7, 13,9 SV26,7, 2,2 3 8,1 16,9 18,9-2/11A -2/D ,8 SV29 1,1 6,82 2,61 3 9,8 22,8 2,4-2/11-2/D ,8 SV29 1,1 6,82 2,61 3 9,8 22,8 2,4-2/1-2/D ,2 SV29 1,1 6,82 2,61 3 9,8 29,2 31,8-2/18-2/D237 18, 33,4 SV29 1,1 6,82 2,61 3 9,8 36,4 39, -2/22-2/D ,9 SV29 1,1 6,82 2,61 3 9,8 4,9 43, 6-12/4 6-12/D ,9 SV26,7, 2,2 3 8,1 1,6 12,6 6-12/ 6-12/D129, 1,7 SV26,7, 2,2 3 8,1 13,7 1,7 6-12/7 6-12/D14 7, 13,9 SV26,7, 2,2 3 8,1 16,9 18,9 6-16/11A 6-16/D ,8 SV26,7, 2,2 3 8,1 22,8 24,8 6-16/ /D ,8 SV26,7, 2,2 3 8,1 22,8 24,8 6-16/1 6-16/D ,2 SV26,7, 2,2 3 8,1 29,2 31,2 6-2/1 6-2/D ,2 SV26,7, 2,2 3 8,1 29,2 31,2 6-2/18 6-2/D198 18, 33,4 SV29 1,1 6,82 2,61 3 9,8 36,4 39, 6-2/22 6-2/D ,9 SV29 1,1 6,82 2,61 3 9,8 4,9 43, 6-2/22 6-2/D ,9 SV29 1,1 6,82 2,61 3 9,8 4,9 43, 6-2/3 6-2/D , SV29 1,1 6,82 2,61 3 9,8 7, 9,6 6-2/37 6-2/D , SV212 1, 8,9 3,4 3 11,9 68, 71, 8-16/1 8-16/D ,2 SV47 1,1 6,82 2,61 3 9,8 29,2 31,8 8-16/ /D173 18, 33,4 SV47 1,1 6,82 2,61 3 9,8 36,4 39, 8-2/22 8-2/D ,9 SV47 1,1 6,82 2,61 3 9,8 4,9 43, 8-2/3 8-2/D27 3 4, SV49 1, 8,9 3,4 3 11,9 7, 6, 8-2/37 8-2/D , SV49 1, 8,9 3,4 3 11,9 68, 71, 8-2/4 8-2/D , SV49 1, 8,9 3,4 3 11,9 83, 86, 8-2/ 8-2/D26 99, SV413 2,2 12,2,3 3 1,2 12, 17, ENMTP-FHF_2p-en_b_te (*)The current indicated is the maximum current absorbed. At the set 3x4V three phase power supply GEN..1D e GEN..11D to add the control panel corrent of the engine pump (GEN..D), 1x23V single phase The sets GEN..1D have the electric jockey pump 1x23V single phase power supply. 3

54 GEN..D/FHF 1-12 BOOSTER SETS ELECTRICAL DATA A TABLE AT Hz SERVICE PUMP ELECTRIC JOCKEY PUMP CURRENT (*) ABSORBED SET 3 X 4 V 1 x 23V 3x4 TYPE NOMINAL 1x23V 3x4V FHF.. POWER ELECTRIC Pn In TIPO Pn In In GEN..D GEN..1D GEN..1D GEN..11D PUMP PUMP kw A kw A A A A A A 1-16/ /D1 18, 33,4 SV47 1,1 6,82 2,61 3 9,8 36,4 39, 1-16/ /D ,9 SV47 1,1 6,82 2,61 3 9,8 4,9 43, 1-16/3 1-16/D18 3 4, SV47 1,1 6,82 2,61 3 9,8 7, 9,6 1-2/18 1-2/D168 18, 33,4 SV47 1,1 6,82 2,61 3 9,8 36,4 39, 1-2/3 1-2/D , SV47 1,1 6,82 2,61 3 9,8 7, 9,6 1-2/37 1-2/D , SV47 1,1 6,82 2,61 3 9,8 68, 7,6 1-2/4 1-2/D , SV49 1, 8,9 3,4 3 11,9 83, 86, 1-2/3 1-2/D2 3 4, SV47 1,1 6,82 2,61 3 9,8 7, 9,6 1-2/4 1-2/D , SV49 1, 8,9 3,4 3 11,9 83, 86, 1-2/ 1-2/D23 99, SV49 1, 8,9 3,4 3 11,9 12, 1, 1-2/7 1-2/D , SV413 2,2 12,2,3 3 1,2 136, 141, 1-2/9 1-2/D , SV413 2,2 12,2,3 3 1,2 16, 16, 12-2/3 12-2/D18 3 4, SV8 2,2 12,2,3 3 1,2 7, 62, 12-2/4 12-2/D26 4 8, SV8 2,2 12,2,3 3 1,2 83, 88, 12-2/ 12-2/D216 99, SV86 3-6, , 18, / /D , SV86 3-6, , 142, / /D , SV87 4-7, , 167, / /D , SV87 4-7,63 4, - 2, 28, / /D , SV89 4-7,63 4, - 239, 247,1 ENMTP-FHF1_2p-en_b_te (*)The current indicated is the maximum current absorbed. At the set 3x4V three phase power supply GEN..1D e GEN..11D to add the control panel corrent of the engine pump (GEN..D), 1x23V single phase The sets GEN..1D have the electric jockey pump 1x23V single phase power supply. 4

55 Fire-fighting booster sets EN 1284 DFHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 6 m 3 /h. Head up to 1 m. Panel supply power voltage: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw. Diesel engine with battery start. Diesel engine service pump in horizontal design: - FHF series. Maximum running pressure: 12 bar.

56 DFHF 32-8 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

57 DFHF 32-8 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 D.. DNA DNM A B C E F H H1 H2 FHFE32-12/D119 R 2" FHFE32-12/D136 R 2" FHFE32-16/D1 R 2" FHFE32-16/D164 R 2" FHFE32-2/D188 R 2" FHFE32-2/D24 R 2" FHFE4-12/D FHFE4-12/D FHFE4-12/D FHFE4-16/D FHFE4-16/D FHFE4-2/D FHFE4-2/D FHFE4-2/D FHFE4-2/D FHFE4-2/D FHFE-12/D FHFE-12/D FHFE-12/D FHFE-16/D FHFE-16/D FHFE-2/D FHFE-2/D FHFE-2/D FHFE-2/D FHFE-2/D FHFE6-12/D FHFE6-12/D FHFE6-12/D FHFE6-16/D FHFE6-16/D FHFE6-16/D FHFE6-2/D FHFE6-2/D FHFE6-2/D FHFE6-2/D FHFE6-2/D FHFE6-2/D FHFE8-16/D FHFE8-16/D FHFE8-2/D FHFE8-2/D FHFE8-2/D FHFE8-2/D FHFE8-2/D Dimensions in mm. Tolerance ± 1 mm. d_fhfe-en_f_td 7

58 DFHF 1-12 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. D.. DNA DNM A B C E F H H1 H2 FHFE1-16/D FHFE1-16/D FHFE1-16/D FHFE1-2/D FHFE1-2/D FHFE1-2/D FHFE1-2/D FHFE1-2/D FHFE1-2/D FHFE1-2/D FHFE1-2/D FHFE1-2/D FHFE12-2/D FHFE12-2/D FHFE12-2/D FHFE12-27/D FHFE12-27/D FHFE12-27/D FHFE12-27/D Dimensions in mm. Tolerance ± 1 mm. d_fhfe1-en_c_td 8

59 Fire-fighting booster sets EN 1284 GEN..D/FHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 6 m 3 /h. Head up to 1 m. Panel supply power voltage: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw. Diesel engine with battery start. Diesel engine service pump in horizontal design: - FHF series. Maximum running pressure: 12 bar. 9

60 GEN..D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

61 GEN..D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D DRW N DNA DNM A B D E G N P Q FHF32-12/D119 1 R 2" R 1"1/ FHF32-12/D136 1 R 2" R 1"1/ FHF32-16/D1 1 R 2" R 1"1/ FHF32-16/D164 1 R 2" R 1"1/ FHF32-2/D188 1 R 2" R 1"1/ FHF32-2/D24 1 R 2" R 1"1/ FHF4-12/D FHF4-12/D FHF4-12/D FHF4-16/D FHF4-16/D FHF4-2/D FHF4-2/D FHF4-2/D FHF4-2/D FHF4-2/D FHF-12/D FHF-12/D FHF-12/D FHF-16/D FHF-16/D FHF-2/D FHF-2/D FHF-2/D FHF-2/D FHF-2/D FHF6-12/D FHF6-12/D FHF6-12/D FHF6-16/D FHF6-16/D FHF6-16/D FHF6-2/D FHF6-2/D FHF6-2/D FHF6-2/D FHF6-2/D FHF6-2/D FHF8-16/D FHF8-16/D FHF8-2/D FHF8-2/D FHF8-2/D FHF8-2/D FHF8-2/D Dimensions in mm. Tolerance ± 1 mm. gend_fhf-en_e_td 61

62 GEN..D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. GEN..D DRW N DNA DNM A B D E G N P Q FHF1-16/D FHF1-16/D FHF1-16/D FHF1-2/D FHF1-2/D FHF1-2/D FHF1-2/D FHF1-2/D FHF1-2/D FHF1-2/D FHF1-2/D FHF1-2/D FHF12-2/D FHF12-2/D FHF12-2/D FHF12-27/D FHF12-27/D FHF12-27/D FHF12-27/D Dimensions in mm. Tolerance ± 1 mm. gend_fhf1-en_c_td 62

63 Fire-fighting booster sets EN 1284 GEN..1D/FHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 6 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 1 x 23V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw. Electric motor start : - Direct start for powers up to 22 kw included for electric pump. Diesel engine with battery start. Service pump in horizontal design: - FHF series. Electric jockey pump with vertical axis: - SV Series (motor protection grade IP). Maximum running pressure: 12 bar. 63

64 GEN..1D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

65 GEN..1D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW DNA DNP DNM A A1 B C D F G H I L N P Q N FHF32-12/D119 1 R 2" Rp 1" R 1"1/ FHF32-12/D136 1 R 2" Rp 1" R 1"1/ FHF32-16/D1 1 R 2" Rp 1" R 1"1/ FHF32-16/D164 1 R 2" Rp 1" R 1"1/ FHF32-2/D188 1 R 2" Rp 1" R 1"1/ FHF32-2/D24 1 R 2" Rp 1" R 1"1/ FHF4-12/D Rp 1" FHF4-12/D Rp 1" FHF4-12/D Rp 1" FHF4-16/D Rp 1" FHF4-16/D Rp 1" FHF4-2/D Rp 1" FHF4-2/D Rp 1" FHF4-2/D Rp 1" FHF4-2/D Rp 1" FHF4-2/D Rp 1" FHF-12/D Rp 1" FHF-12/D Rp 1" FHF-12/D Rp 1" FHF-16/D Rp 1" FHF-16/D Rp 1" FHF-2/D Rp 1" FHF-2/D Rp 1" FHF-2/D Rp 1" FHF-2/D Rp 1" FHF-2/D2 2 6 Rp 1" FHF6-12/D Rp 1" FHF6-12/D Rp 1" FHF6-12/D Rp 1" FHF6-16/D Rp 1" FHF6-16/D Rp 1" FHF6-16/D Rp 1" FHF6-2/D Rp 1" FHF6-2/D Rp 1" FHF6-2/D Rp 1" FHF6-2/D Rp 1" FHF6-2/D Rp 1" FHF6-2/D Rp 1" FHF8-16/D Rp 1"1/ FHF8-16/D Rp 1"1/ FHF8-2/D Rp 1"1/ FHF8-2/D Rp 1"1/ FHF8-2/D Rp 1"1/ FHF8-2/D Rp 1"1/ FHF8-2/D Rp 1"1/ Dimensions in mm. Tolerance ± 1 mm. gen1d_fhf-en_e_td 6

66 GEN..1D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

67 GEN..1D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW DNA DNP DNM A A1 B C D F G H I L N P Q N FHF1-16/D Rp 1"1/ FHF1-16/D Rp 1"1/ FHF1-16/D Rp 1"1/ FHF1-2/D Rp 1"1/ FHF1-2/D Rp 1"1/ FHF1-2/D Rp 1"1/ FHF1-2/D Rp 1"1/ FHF1-2/D Rp 1"1/ FHF1-2/D Rp 1"1/ FHF1-2/D Rp 1"1/ FHF1-2/D Rp 1"1/ \ FHF1-2/D Rp 1"1/ \ FHF12-2/D Rp 1"1/ FHF12-2/D Rp 1"1/ FHF12-2/D Rp 1"1/ FHF12-27/D Rp 1"1/ \ FHF12-27/D Rp 1"1/ \ FHF12-27/D Rp 1"1/ \ FHF12-27/D Rp 1"1/ \ Dimensions in mm. Tolerance ± 1 mm. gen1d_fhf1-en_d_td 67

68 68

69 Fire-fighting booster sets EN 1284 GEN..1D/FHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 13 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 3 x 4V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw. Electric motor start : - Direct start for powers up to 22 kw included for pump (GEND...). - Star/delta start for higher powers (GENY... set). Diesel engine with battery start. Service pump in horizontal design: - FHF series (IP electric motor protection). Maximum running pressure: 12 bar. 69

70 GEN..1D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

71 GEN..1D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW DNA DNM A A1 B C D G H I L N P Q N FHF32-12/7/D119 1 R 2" R 2" FHF32-12/11/D136 1 R 2" R 2" FHF32-16/1/D1 1 R 2" R 2" FHF32-16/22/D164 1 R 2" R 2" FHF32-2/3/D188 1 R 2" R 2" FHF32-2/4/D24 1 R 2" R 2" FHF4-12/11/D FHF4-12/1/D FHF4-12/22/D FHF4-16/3/D FHF4-16/4/D FHF4-2//D FHF4-2/7/D FHF4-2/11A/D FHF4-2/11/D FHF4-2/1/D FHF-12/22/D FHF-12/3/D FHF-12/4/D FHF-16//D FHF-16/7/D FHF-2/11A/D FHF-2/11/D FHF-2/1/D FHF-2/18/D FHF-2/22/D FHF6-12/4/D FHF6-12//D FHF6-12/7/D FHF6-16/11A/D FHF6-16/11/D FHF6-16/1/D FHF6-2/1/D FHF6-2/18/D FHF6-2/22/D FHF6-2/22/D FHF6-2/3/D FHF6-2/37/D FHF8-16/1/D FHF8-16/18/D FHF8-2/22/D FHF8-2/3/D FHF8-2/37/D FHF8-2/4/D FHF8-2//D Dimensions in mm. Tolerance ± 1 mm. gen1d_fhf-en_d_td 71

72 72

73 Fire-fighting booster sets EN 1284 GEN..11D/FHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 13 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 3 x 4V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw. Electric motor start : - Direct start for powers up to 22 kw included for pump (GEND...). - Star/delta start for higher powers (GENY... set). Diesel engine with battery start. Service pump in horizontal design: - FHF series (IP electric motor protection). Electric jockey pump with vertical axis: - SV Series (motor protection grade IP). Maximum running pressure: 12 bar. 73

74 GEN..11D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

75 GEN..11D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..11D DRW DNA DNP DNM A A1 B C D F G H I I1 L N P Q N FHF32-12/7/D119 1 R 2" Rp 1" R 2" FHF32-12/11/D136 1 R 2" Rp 1" R 2" FHF32-16/1/D1 1 R 2" Rp 1" R 2" FHF32-16/22/D164 1 R 2" Rp 1" R 2" FHF32-2/3/D188 1 R 2" Rp 1" R 2" FHF32-2/4/D24 1 R 2" Rp 1" R 2" FHF4-12/11/D Rp 1" FHF4-12/1/D Rp 1" FHF4-12/22/D Rp 1" FHF4-16/3/D Rp 1" FHF4-16/4/D Rp 1" FHF4-2//D Rp 1" FHF4-2/7/D Rp 1" FHF4-2/11A/D Rp 1" FHF4-2/11/D Rp 1" FHF4-2/1/D Rp 1" FHF-12/22/D Rp 1" FHF-12/3/D Rp 1" FHF-12/4/D Rp 1" FHF-16//D Rp 1" FHF-16/7/D Rp 1" FHF-2/11A/D Rp 1" FHF-2/11/D Rp 1" FHF-2/1/D Rp 1" FHF-2/18/D Rp 1" FHF-2/22/D2 2 6 Rp 1" FHF6-12/4/D Rp 1" FHF6-12//D Rp 1" FHF6-12/7/D Rp 1" FHF6-16/11A/D Rp 1" FHF6-16/11/D Rp 1" FHF6-16/1/D Rp 1" FHF6-2/1/D Rp 1" FHF6-2/18/D Rp 1" FHF6-2/22/D Rp 1" FHF6-2/22/D Rp 1" FHF6-2/3/D Rp 1" FHF6-2/37/D Rp 1" FHF8-16/1/D Rp 1"1/ FHF8-16/18/D Rp 1"1/ FHF8-2/22/D Rp 1"1/ FHF8-2/3/D Rp 1"1/ FHF8-2/37/D Rp 1"1/ FHF8-2/4/D Rp 1"1/ FHF8-2//D Rp 1"1/ Dimensions in mm. Tolerance ± 1 mm. gen11d_fhf-en_e_td 7

76 GEN..11D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

77 GEN..11D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..11D DRW DNA DNP DNM A A1 B C D F G H I I1 L N P Q N FHF1-16/18/D Rp 1"1/ FHF1-16/22/D Rp 1"1/ FHF1-16/3/D Rp 1"1/ FHF1-2/18/D Rp 1"1/ FHF1-2/3/D Rp 1"1/ FHF1-2/37/D Rp 1"1/ FHF1-2/4/D Rp 1"1/ FHF1-2/3/D Rp 1"1/ FHF1-2/4/D Rp 1"1/ FHF1-2//D Rp 1"1/ FHF1-2/7/D Rp 1"1/ \ FHF1-2/9/D Rp 1"1/ \ FHF12-2/3/D Rp 1"1/ FHF12-2/4/D Rp 1"1/ FHF12-2//D Rp 1"1/ FHF12-27/7/D Rp 1"1/ \ FHF12-27/9/D Rp 1"1/ \ FHF12-27/11/D Rp 1"1/ \ FHF12-27/132/D Rp 1"1/ \ Dimensions in mm. Tolerance ± 1 mm. gen11d_fhf1-en_c_td 77

78 78

79 GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q 1 [Imp gpm] Q [US gpm],2,8,2, Q [US gpm],2,8,2,6,1,1,4,1,1,4,,2,,2, 6,, 1, Q [m 3 /h] Q [l/min] 76474_A_CH Q [m 3 /h] Q [l/min] 7647_A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q 12 [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US 2gpm],,4 1,,4 1,,3 1,,3 1,,2,2,,,1,1, 1,, 1, Q [m 3 /h] Q [l/min] 76476_A_CH Q [m 3 /h] Q 1 [l/min] 76477_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 79

80 GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 2gpm], Q [US 2gpm],6,4 1,, 1,,3 1,,4,3 1,,2,1,,2,1,, 1,, 1, Q [m 3 /h] Q 1 [l/min] 76478_A_CH Q [m 3 /h] Q 1 [l/min] 7646_A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 2gpm], , Q [US gpm], 1,,4 1,,4,3 1,,3 1,,2,2,1,,1,, 1,, 1, Q [m 3 /h] Q 1 [l/min] 7647_A_CH Q [m 3 1 /h] Q [l/min] 76481_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 8

81 GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] , Q [US gpm] Q [US gpm],,4 1,,4 1,,3 1,,3 1,,2,2,,,1,1, 1,, 1, Q [m1 3 /h] Q 16 [l/min] 76482_A_CH Q [m12 3 /h] 1 1 Q [l/min] _A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US 6 gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, Q [m12 3 /h] 1 1 Q [l/min] _A_CH Q [m14 3 /h] Q [l/min] 7648_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 81

82 GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 7 gpm], Q [US 7 gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, /11A φ /1 Ø /1 φ /1 Ø /1 φ /11 φ /22 φ /18 φ Q [m16 3 /h] Q [l/min] 76486_A_CH Q [m16 3 /h] Q [l/min] 76487_A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 7 gpm], , Q [US gpm], 1,,4 1,,4,3 1,,3 1,,2,2,1,,1,, 1,, 1, /1 Ø /1 Ø Q [m16 3 /h] Q [l/min] 76488_A_CH Q [m2 3 /h] Q 4 [l/min] 76489_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 82

83 GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] , Q [US gpm] , Q [US gpm],4 1,,4 1,,3 1,,3 1,,2,2,,,1,1, 1,, 1, /1 Ø /37 φ /1 Ø / φ /4 φ Q [m2 3 /h] Q 4 [l/min] 7649_A_CH Q [m2 3 /h] Q 4 [l/min] 76491_A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q 14 [Imp gpm] Q 14 [Imp gpm] ,2 Q [US gpm], ,2 Q [US gpm],8,2,2,6,6,1,1,4,4,1,1,,2,,2, 1,, 1, 1-16/18 φ 13/ /18 φ 141/ /3 φ /22 φ 19/ /1 Ø /1 Ø /4 φ /37 φ /3 φ 189/ Q [m4 3 /h] Q [l/min] 76492_A_CH Q [m4 3 /h] Q [l/min] 76493_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 83

84 GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A 1 1 Q [Imp gpm] Q 2 [Imp gpm] 1 1,2,2 Q [US gpm],8, Q 3 [US gpm],2,8,2,6,1,1,4,1,1,4,,2,,2, 1,, 1, /3 φ 162/ /3 φ /1 Ø /9 φ / φ /4 φ /1 Ø /7 φ / φ /4 φ Q [m 3 /h] Q [l/min] 76494_A_CH Q [m7 3 /h] Q [l/min] 7649_A_CH FH [rpm] ISO Annex A Q [Imp gpm] Q [US 3gpm],2,8,2,6,1,1,4,,2, 2, /7 φ 216/ /132 φ / /11 φ 23 Ø /9 φ Q [m8 3 /h] Q [l/min] 76496_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 84

85 GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [US gpm], Q 1 [Imp gpm] Q [US gpm],6,4 1,, 1,,3 1,,4,3 1,,2,1,,2,1,, 6,, 1, Q [m 3 /h] Q [l/min] 7641_A_CH Q [m 3 /h] Q [l/min] 7642_A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q 12 [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US 2gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, Q [m 3 /h] Q [l/min] 7643_A_CH Q [m 3 /h] Q 1 [l/min] 7644_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 8

86 GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 2gpm], Q [US 2gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, Q [m 3 /h] Q 1 [l/min] 764_A_CH Q [m 3 /h] Q 1 [l/min] 7646_A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 2gpm], ,6 Q [US gpm],, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, Q [m 3 /h] Q 1 [l/min] 7647_A_CH Q [m1 3 /h] Q [l/min] 7648_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 86

87 GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] ,6 Q [US gpm] Q [US gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, Q [m1 3 /h] Q 16 [l/min] 7649_A_CH Q [m12 3 /h] 1 1 Q [l/min] _A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US 6 gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, Q [m12 3 /h] 1 1 Q [l/min] _A_CH Q [m14 3 /h] Q [l/min] 76461_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 87

88 GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 7 gpm], Q [US 7 gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, /11A φ /1 Ø /1 φ /1 Ø /1 φ /11 φ /22 φ /18 φ Q [m16 3 /h] Q [l/min] 76462_A_CH Q [m16 3 /h] Q [l/min] 76463_A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 7 gpm], ,6 Q [US gpm],, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, /1 Ø /1 Ø Q [m16 3 /h] Q [l/min] 76464_A_CH Q [m2 3 /h] Q 4 [l/min] 7646_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 88

89 GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] ,6 Q [US gpm] ,6 Q [US gpm],, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, /1 Ø /37 φ /1 Ø / φ /4 φ Q [m2 3 /h] Q 4 [l/min] 76466_A_CH Q [m2 3 /h] Q 4 [l/min] 76467_A_CH FH [rpm] ISO Annex A FH [rpm] ISO Annex A Q 14 [Imp gpm] Q 14 [Imp gpm] ,2 Q [US gpm], ,2 Q [US gpm],8,2,2,6,6,1,1,4,4,1,1,,2,,2, 1,, 1, 1-16/18 φ 13/ /18 φ 141/ /3 φ /22 φ 19/ /1 Ø /1 Ø /4 φ /37 φ /3 φ 189/ Q [m4 3 /h] Q [l/min] 76468_A_CH Q [m4 3 /h] Q [l/min] 76469_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 89

90 GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH [rpm] ISO Annex A FH [rpm] ISO Annex A 1 1 Q [Imp gpm] Q 2 [Imp gpm] 1 1,2,2 Q [US gpm],8, Q 3 [US gpm],2,8,2,6,1,1,4,1,1,4,,2,,2, 1,, 1, /3 φ 162/ /3 φ /1 Ø /9 φ / φ /4 φ /1 Ø /7 φ / φ /4 φ Q [m 3 /h] Q [l/min] 7647_A_CH Q [m7 3 /h] Q [l/min] 76471_A_CH FH [rpm] ISO Annex A Q [Imp gpm] Q [US 3gpm],2,8,2,6,1,1,4,,2, 2, /7 φ 216/ /132 φ / /11 φ 23 Ø /9 φ Q [m8 3 /h] Q [l/min] 76472_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 9

91 GEN..D/SHF Series Fire-fighting booster sets EN 1284, high-efficiency electric pumps with PLM motors and series SHF horizontal centrifugal diesel engine pumps Hz 91

92 92

93 RANGE GEN..D/SHF RANGE The range of EN 1284 fire-fighting booster sets with diesel and electric service pumps and optional jockey pump to adapt to the specific needs of every application. D.. DIESEL ENGINE PUMP Single fire-fighting centrifugal pump in horizontal design with stainless steel casing, SHF series. Head up to 1 m. Flow up to 22 m 3 /h. GEN..D SERIES Fire-fighting sets with diesel engine centrifugal service pump, in horizontal design with stainless steel casing, SHF series. Head up to 1 m. Flow up to 22 m 3 /h. GEN..1D SERIES Fire-fighting sets with diesel engine service pump and electric jockey pump. The centrifugal service pump has horizontal design and stainless steel casing. SHF series. Head up to 1 m. Flow up to 22 m 3 /h. GEN..1D SERIES Fire-fighting sets with diesel engine centrifugal service pump. The centrifugal service pump has horizontal design and stainless steel casing. SHF series. Head up to 1 m. Flow up to 44 m 3 /h. GEN..11D SERIES Fire-fighting sets with diesel engine service pump, electric service pump and electric jockey pump. The centrifugal service pump has horizontal design and stainless steel casing. SHF series. Head up to 1 m. Flow up to 44 m 3 /h. 93

94 GEN..D/SHF BOOSTER SETS SERIES HYDRAULIC PERFORMANCE TABLE AT HZ (JOCKEY PUMP) PUMP NOMINAL Q = DELIVERY TYPE POWER l/min m 3 /h 1,2 1,8 2,4 3 3,6 4,2 6 7,2 8 kw HP H = TOTAL HEAD METRES COLUMN OF WATER SV2 4,,7 42, 37, 34, 3, 26, 2, 1, SV2 6,7 1 64, 6, 1, 4, 38, 31, 22, SV2 9 1,1 1, 96, 84, 76, 68, 8, 46, 32, SV2 12 1, 2 128, 112, 12, 91, 77, 62, 44, SV2 14 2,2 3 1, 131, 119, 16, 9, 73, 2, SV2 1 2,2 3 16,2 14,3 128,2 114, 97,4 78,2,9 SV4 7 1,1 1, 7, 9, 6, 3, 1, 37, 26, 18, SV4 9 1, 2 9, 76, 73, 68, 6, 47, 33, 23, SV4 13 2, , 111, 1, 99, 9, 68, 48, 34, Performance in accordance with the ISO Annex A Standard. EN1284_pp_sv2-4-2p-en_b_th 94

95 GEN..D/SHF BOOSTER SETS SERIES SERVICE PUMP JOCKEY PUMP COMBINATIONS SERVICE PUMP JOCKEY PUMP ELECTRIC PUMP TYPE SHF PUMP 32-12/ /D / /D / /D / /D /3 32-2/D /4 32-2/D / 32-2/D /7 32-2/D / /D / /D /1 4-12/D / /D /3 4-16/D /4 4-16/D / 4-2/D19 4-2/7 4-2/D29 4-2/11A 4-2/D /11 4-2/D /1 4-2/D21-12/22-12/D119-12/3-12/D13-12/4-12/D139-16/ -16/D18-16/7-16/D174-2/11A -2/D197-2/11-2/D29-2/1-2/D224-2/18-2/D237-2/22-2/D2 6-16/4 6-16/D / 6-16/D /7 6-16/D /11A 6-16/D / /D /1 6-2/D /18 6-2/D23 6-2/22 6-2/D21 6-2/3 6-2/D24 6-2/37 6-2/D2 8-16/ /D /1 8-16/D / /D /22 8-2/D /3 8-2/D21 8-2/37 8-2/D /4 8-2/D / 8-2/D22 8-2/7 8-2/D27 SV2 4 SV2 6 SV2 9 SV2 12 SV2 14 SV2 1 SV4 7 SV4 9 SV4 13 SV8 SV8 6 SV8 7 SV SHF_ap-en_a_tc 9

96 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/SHF 32 BOOSTER SETS SERIES RISK CLASS TYPE RATED LHn SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 32-12/ /D121 1 x,7 16,7 14, 12,9 12,1 11, 7,6,1 3,7 1, / /D136 1 x 1,1 21,6 19, 17,9 17, 1,9 12,3 9,6 8,1 6, / /D1 1 x 1, 27,6 24,2 22,9 21,8 2, 16,3 13, 11,3 9, / /D168 1 x 2,2 3, 32, 3,9 29,9 28,7 24,7 21, 19,7 17, 16,1 1,2 13,1 32-2/3 32-2/D188 1 x 3 43,8 38,1 36,4 3,1 33,4 28, 23,9 21,6 18,8 17,1 32-2/4 32-2/D24 1 x 4 3,6 48,6 47,1 4,9 44,4 39,3 3,1 32,8 29,9 28,1 27, 24,1 32-2/ 32-2/D222 1 x, 61,7 6,3 4,6 3,2 1,6 46, 41,7 39,3 36,4 32-2/7 32-2/D242 1 x 7, 74,1 68,4 66,7 6,3 63,6 8,1 3,8 1,4 48,6 46,9 4,8 32-2/ /D26 1 x 11 86,3 79,8 77,9 76, 74,7 69, 64,7 62,3 9, 7,8 6,7 4, Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-shf32-2p-en_a_th LHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/SHF 32 BOOSTER SETS SERIES RISK CLASS TYPE RATED LHn SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 32-12/ /D121 1 x,7 16,7 14, 12,9 12,1 11, 7,6,1 3,7 1, / /D136 1 x 1,1 21,6 19, 17,9 17, 1,9 12,3 9,6 8,1 6, / /D1 1 x 1, 27,6 24,2 22,9 21,8 2, 16,3 13, 11,3 9, / /D168 1 x 2,2 3, 32, 3,9 29,9 28,7 24,7 21, 19,7 17, 16,1 1,2 13,1 32-2/3 32-2/D188 1 x 3 43,8 38,1 36,4 3,1 33,4 28, 23,9 21,6 18,8 17,1 32-2/4 32-2/D24 1 x 4 3,6 48,6 47,1 4,9 44,4 39,3 3,1 32,8 29,9 28,1 27, 24,1 32-2/ 32-2/D222 1 x, 61,7 6,3 4,6 3,2 1,6 46, 41,7 39,3 36,4 32-2/7 32-2/D242 1 x 7, 74,1 68,4 66,7 6,3 63,6 8,1 3,8 1,4 48,6 46,9 4,8 32-2/ /D26 1 x 11 86,3 79,8 77,9 76, 74,7 69, 64,7 62,3 9, 7,8 6,7 4, Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-shf32-2p-en_a_th LHn = risk class value referred to the required rated capacity (Tab.6 para EN1284). Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

97 NPSH REQUIRED FOR PUMP SERIES SHF 32 RISK CLASS TYPE RATED LHn SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 32-12/ /D121 1 x,7 1, 1, 1,1 1,2 1,6 2,1 2,3 2, / /D136 1 x 1,1 1, 1, 1,1 1,2 1,6 2,1 2,3 2, / /D1 1 x 1, 1, 1,6 1,7 1,9 2, 3, 3,2 3, 32-16/ /D168 1 x 2,2 1,2 1,4 1, 1,6 2,2 2,8 3,3 3,8 4,2 4,4,2 32-2/3 32-2/D188 1 x 3 1,7 1,8 1,9 2,1 2,8 3,7 4,3,2,8 32-2/4 32-2/D24 1 x 4 1,6 1,8 2, 2,2 2,8 3,4 3,9 4,6,1, 6,9 32-2/ 32-2/D222 1 x, 2,8 3,2 3, 3,8,1 6,2 6,9 7,7 32-2/7 32-2/D242 1 x 7, 2,7 3, 3,2 3, 4,,3,8 6,3 6,6 6,9 32-2/ /D26 1 x 11 2,7 3, 3,2 3, 4,,3,8 6,3 6,6 6,9 7, The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-shf32-2p_NPSHr-en_a_th LHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Check that NPSHd NPSHr+1m is satisfied 97

98 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/SHF 4 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH1n SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4-12/ /D112 1 x 1,1 13,9 11,3 1, 9,3 3,4,7 4-12/1 4-12/D126 1 x 1, 18, 1,3 14, 13,3 7,4 4,7 4-12/ /D143 1 x 2,2 2,3 21,8 2, 19,8 14, 11,4 6,4, 3,6,6 4-16/3 4-16/D19 1 x 3 31,6 28,1 26,8 26, 19, 16, 1,8 9,2 7,6 4-16/4 4-16/D171 1 x 4 38,3 3,1 33,7 32,9 26, 23,6 18,1 16, 1, 11,7 4-2/ 4-2/D19 1 x, 46,4 42,7 41,2 4,4 33,1 29,7 23,3 21, 19,6 4-2/7 4-2/D29 1 x 7, 7, 3,1 1,6,7 43,8 4,7 34,8 33,2 31, 28, 4-2/11A 4-2/D218 1 x 11 63,6 7,8 6,2,2 47,8 44, 38,2 36, 34,8 31,1 4-2/11 4-2/D233 1 x 11 71,7 66, 64,3 63,4,7 2,3 4,8 44, 42,1 38,3 4-2/1 4-2/D21 1 x 1 8, 78,6 76,9 76, 68,4 6, 8,6 6,8, 1,1 42,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-shf4-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/SHF 4 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH1n SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4-12/ /D112 1 x 1,1 13,9 11,3 1, 9,3 3,4,7 4-12/1 4-12/D126 1 x 1, 18, 1,3 14, 13,3 7,4 4,7 4-12/ /D143 1 x 2,2 2,3 21,8 2, 19,8 14, 11,4 6,4, 3,6,6 4-16/3 4-16/D19 1 x 3 31,6 28,1 26,8 26, 19, 16, 1,8 9,2 7,6 4-16/4 4-16/D171 1 x 4 38,3 3,1 33,7 32,9 26, 23,6 18,1 16, 1, 11,7 4-2/ 4-2/D19 1 x, 46,4 42,7 41,2 4,4 33,1 29,7 23,3 21, 19,6 4-2/7 4-2/D29 1 x 7, 7, 3,1 1,6,7 43,8 4,7 34,8 33,2 31, 28, 4-2/11A 4-2/D218 1 x 11 63,6 7,8 6,2,2 47,8 44, 38,2 36, 34,8 31,1 4-2/11 4-2/D233 1 x 11 71,7 66, 64,3 63,4,7 2,3 4,8 44, 42,1 38,3 4-2/1 4-2/D21 1 x 1 8, 78,6 76,9 76, 68,4 6, 8,6 6,8, 1,1 42,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-shf4-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

99 NPSH REQUIRED FOR PUMP SERIES SHF 4 RISK CLASS TYPE RATED OH1n OH1m SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 4-12/ /D112 1 x 1,1,7 1, 1, 2, 4-12/1 4-12/D126 1 x 1,,7 1, 1, 2, 2,3 2, 4-12/ /D143 1 x 2,2,7 1, 1, 2, 2,3 2, 2,8 3,1 4-16/3 4-16/D19 1 x 3 1,1 1,4 2,1 2,6 2,9 3,2 3, 3,8 4-16/4 4-16/D171 1 x 4 1,1 1,4 2,1 2,6 2,9 3,2 3, 3,8 4,9 4-2/ 4-2/D19 1 x, 1,4 1,8 2,7 3,4 3,7 3,9 4,2 4,,4 4-2/7 4-2/D29 1 x 7, 1,4 1,8 2,7 3,4 3,7 3,9 4,2 4,,4 6,4 4-2/11A 4-2/D218 1 x 11 1,4 1,4 1,7 3, 4,1, 4-2/11 4-2/D233 1 x 11 1,3 1,4 1,6 1,8 1,9 4-2/1 4-2/D21 1 x 1 1,3 1,4 1,6 1,8 1,9 2,1 2,2 2, 3,3 4,3, The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = risk class value referred to the required rated and maximum capacity (Tab.6 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-shf4-2p_NPSHr-en_a_th 99

100 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/SHF BOOSTER SETS SERIES RISK CLASS TYPE RATED OH2n OH3n SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 17,2 13,2 12, 11,3,9 3,6 1,2-12/3-12/D13 1 x 3 21,7 17,4 16,1 1,3 9,8 7,6,2 2,8-12/4-12/D139 1 x 4 2,6 21,8 2,6 19,8 14,4 12,1 9,8 7,3 6,,3 4,7-16/ -16/D18 1 x, 34, 29,3 27,8 26,9 2,4 17, 14,4 11,1 9,4 8,3 7,6-16/7-16/D174 1 x 7, 4,7 36,1 34,7 33,9 27,6 24,7 21,6 18,1 16,3 1,2 14,4 12, 1,4-2/11A -2/D197 1 x 11 34, 29,3 27,8 26,9 2,4 17, 14,4 11,1 9,4 8,3 7,6-2/11-2/D29 1 x 11 4,7 36,1 34,7 33,9 27,6 24,7 21,6 18,1 16,3 1,2 14,4 12, -2/1-2/D224 1 x 1 7,3 6, 64, 63, 4,6,4 4,4 39,6-2/18-2/D237 1 x 18, 8,1 73,8 72,1 71,1 62,8 8,7 4,1 48,9 46, 44,2-2/22-2/D2 1 x 22 88,9 83,2 81,6 8,6 72,3 68,4 64, 9,1 6,4 4,7 3,6,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-shf-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/SHF BOOSTER SETS SERIES RISK CLASS TYPE RATED OH2n OH3n SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 17,2 13,2 12, 11,3,9 3,6 1,2-12/3-12/D13 1 x 3 21,7 17,4 16,1 1,3 9,8 7,6,2 2,8-12/4-12/D139 1 x 4 2,6 21,8 2,6 19,8 14,4 12,1 9,8 7,3 6,,3 4,7-16/ -16/D18 1 x, 34, 29,3 27,8 26,9 2,4 17, 14,4 11,1 9,4 8,3 7,6-16/7-16/D174 1 x 7, 4,7 36,1 34,7 33,9 27,6 24,7 21,6 18,1 16,3 1,2 14,4 12, 1,4-2/11A -2/D197 1 x 11 34, 29,3 27,8 26,9 2,4 17, 14,4 11,1 9,4 8,3 7,6-2/11-2/D29 1 x 11 4,7 36,1 34,7 33,9 27,6 24,7 21,6 18,1 16,3 1,2 14,4 12, -2/1-2/D224 1 x 1 7,3 6, 64, 63, 4,6,4 4,4 39,6-2/18-2/D237 1 x 18, 8,1 73,8 72,1 71,1 62,8 8,7 4,1 48,9 46, 44,2-2/22-2/D2 1 x 22 88,9 83,2 81,6 8,6 72,3 68,4 64, 9,1 6,4 4,7 3,6,6 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-shf-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

101 NPSH REQUIRED FOR PUMP SERIES SHF RISK CLASS TYPE RATED OH2n OH2m OH3n OH3m SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] -12/22-12/D119 1 x 2,2 1,6 1,8 1,9 2,8 3,4 4,3-12/3-12/D13 1 x 3 1,6 1,8 1,9 2,7 3,1 3,7 4,6-12/4-12/D139 1 x 4 1,6 1,8 1,9 2,7 3,1 3,7 4,6,2,7 6, -16/ -16/D18 1 x, 2, 2,1 2,1 2,8 3,2 3,7 4,7,4,9 6,3-16/7-16/D174 1 x 7, 1,9 2,1 2,2 2,8 3,1 3,6 4,3 4,9,3,6 6, 7,6-2/11A -2/D197 1 x 11 2, 2,1 2,1 2,8 3,2 4,,2 6,1 6,7 7,2-2/11-2/D29 1 x 11 1,9 2,1 2,2 2,8 3,2 3,7 4,7,4,9 6,3 7, -2/1-2/D224 1 x 1 1,6 1,7 1,8 2,3 2,7 3,3 4,8-2/18-2/D237 1 x 18, 1, 1,7 1,8 2,4 2,7 3,1 3,7 4,1 4,4-2/22-2/D2 1 x 22 1, 1,7 1,8 2,4 2,7 3,1 3,7 4,1 4,4 4,7,4 The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = risk class value referred to the required rated and maximum capacity (Tab.6 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-shf-2p_NPSHr-en_a_th 11

102 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/SHF 6 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH3n OH4n SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 6-16/4 6-16/D119 1 x 4 19,6 1,9 14,9 13,8 12,6 9,4 7,3 2,9 6-16/ 6-16/D129 1 x, 24,2 2, 19, 18,4 17,2 13,9 11,7 7,,4 6-16/7 6-16/D137 1 x 7, 28,2 2,1 24,2 23,1 22, 18,8 16,7 12, 1,4 8,7 6-16/11A 6-16/D168 1 x 11 38,2 34,3 33, 31, 29,8 2,2 22, 1,2 12,9 6-16/ /D177 1 x 11 42,9 39,7 38,4 36,9 3,3 3,6 27,4 2, 18,1 1,6 6-2/1 6-2/D192 1 x 1 3, 47, 4,9 44,1 38,9 3,3 27,1 24,1 6-2/18 6-2/D23 1 x 18, 6,2,2 3,6 1,9 46,9 43,4 3, 32,6 29, 6-2/22 6-2/D21 1 x 22 68, 63, 61,6 6,,2 1,9 44,3 41, 38, 37, 3, 6-2/3 6-2/D24 1 x 3 83,7 8,2 78,9 74,9 71,9 64,4 61,4 8,3 6,6 4,9 6-2/37 6-2/D2 1 x 37 96,7 93,6 92,2 88, 84,9 77,4 74,6 71,7 7,1 68, 6,2 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-shf6-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/SHF 6 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH3n OH4n SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 6-16/4 6-16/D119 1 x 4 19,6 1,9 14,9 13,8 12,6 9,4 7,3 2,9 6-16/ 6-16/D129 1 x, 24,2 2, 19, 18,4 17,2 13,9 11,7 7,,4 6-16/7 6-16/D137 1 x 7, 28,2 2,1 24,2 23,1 22, 18,8 16,7 12, 1,4 8,7 6-16/11A 6-16/D168 1 x 11 38,2 34,3 33, 31, 29,8 2,2 22, 1,2 12,9 6-16/ /D177 1 x 11 42,9 39,7 38,4 36,9 3,3 3,6 27,4 2, 18,1 1,6 6-2/1 6-2/D192 1 x 1 3, 47, 4,9 44,1 38,9 3,3 27,1 24,1 6-2/18 6-2/D23 1 x 18, 6,2,2 3,6 1,9 46,9 43,4 3, 32,6 29, 6-2/22 6-2/D21 1 x 22 68, 63, 61,6 6,,2 1,9 44,3 41, 38, 37, 3, 6-2/3 6-2/D24 1 x 3 83,7 8,2 78,9 74,9 71,9 64,4 61,4 8,3 6,6 4,9 6-2/37 6-2/D2 1 x 37 96,7 93,6 92,2 88, 84,9 77,4 74,6 71,7 7,1 68, 6,2 Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-shf6-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

103 NPSH REQUIRED FOR PUMP SERIES SHF 6 RISK CLASS TYPE RATED OH3n OH3m OH4n OH4m SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 6-16/4 6-16/D119 1 x 4 1,9 1,8 1,9 1,9 2, 2,7 3,3 7,4 6-16/ 6-16/D129 1 x, 1,9 1,9 1,9 1,9 2,4 2,6 3,1,4 6,6 6-16/7 6-16/D137 1 x 7, 1,9 1,9 1,9 1,9 2,4 2,6 3,1,4 6,6 8, 6-16/11A 6-16/D168 1 x 11 1,3 1,4 1,6 1,7 2,1 2,1 2,4 3, 4,2 6-16/ /D177 1 x 11 1,3 1,4 1,6 1,7 2,1 2,1 2,4 3, 4,2,2 6-2/1 6-2/D192 1 x 1 1,7 1,7 1,6 1,7 1,7 1,9 4,1 6,4 6-2/18 6-2/D23 1 x 18, 1,7 1,7 1,6 1,7 1,7 1,9 3, 3,9,3 6-2/22 6-2/D21 1 x 22 1,7 1,7 1,6 1,7 1,7 1,9 3, 3,9,3 7, 6-2/3 6-2/D24 1 x 3 1,3 1,3 1,4 1, 1,7 3,2 4,1,4 7, 6-2/37 6-2/D2 1 x 37 1,3 1,3 1,3 1,4 1,6 2,9 3,7 4,8 6,2 8,1 The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = risk class value referred to the required rated and maximum capacity (Tab.6 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-shf6-2p_NPSHr-en_a_th 13

104 HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/SHF 8 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH4n HH1n SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 8-16/ /D169 1 x 11 33, 3,9 28,6 2,7 22,2 19,7 6,2 4,8 8-16/1 8-16/D177 1 x 1 39, 37,8 3,6 32,7 29,4 26,9 13,2 11,8 8,4 8-16/ /D186 1 x 18, 46,4 44,7 42,6 39,8 36,6 34,2 2,7 19,3 1,9 14,1 12,4 8-2/22 8-2/D198 1 x 22 1,9 48, 4,8 42, 4,1 26,7 2,3 21,9 2,2 8-2/3 8-2/D21 1 x 3 62,2 9,7 7,1 3,9 1, 37,8 36,4 32,9 31,1 29,3 27,4 8-2/37 8-2/D226 1 x 37 69,8 69,9 68,1 6,7 62,8 6, 47,2 4,7 42,2 4,4 38, 36,6 32,7 8-2/4 8-2/D237 1 x 4 82,2 79,1 76,2 72,6 69,8 3,3 1, 47, 44,6 8-2/ 8-2/D22 1 x 93,9 91,9 89,2 8,9 83,2 67,7 66, 61,8 9,6 7,3 8-2/7 8-2/D27 1 x 7 19,7 18,6 16, 12,7 1,2 8, 83,3 79,2 77, 74,8 72, Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-sp-shf8-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/SHF 8 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH4n HH1n SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m3/h PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 8-16/ /D169 1 x 11 33, 3,9 28,6 2,7 22,2 19,7 6,2 4,8 8-16/1 8-16/D177 1 x 1 39, 37,8 3,6 32,7 29,4 26,9 13,2 11,8 8,4 8-16/ /D186 1 x 18, 46,4 44,7 42,6 39,8 36,6 34,2 2,7 19,3 1,9 14,1 12,4 8-2/22 8-2/D198 1 x 22 1,9 48, 4,8 42, 4,1 26,7 2,3 21,9 2,2 8-2/3 8-2/D21 1 x 3 62,2 9,7 7,1 3,9 1, 37,8 36,4 32,9 31,1 29,3 27,4 8-2/37 8-2/D226 1 x 37 69,8 69,9 68,1 6,7 62,8 6, 47,2 4,7 42,2 4,4 38, 36,6 32,7 8-2/4 8-2/D237 1 x 4 82,2 79,1 76,2 72,6 69,8 3,3 1, 47, 44,6 8-2/ 8-2/D22 1 x 93,9 91,9 89,2 8,9 83,2 67,7 66, 61,8 9,6 7,3 8-2/7 8-2/D27 1 x 7 19,7 18,6 16, 12,7 1,2 8, 83,3 79,2 77, 74,8 72, Performance levels relative to set with 1 service pump running and compliant with ISO Annex A. 1284_1pg-st-shf8-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN

105 NPSH REQUIRED FOR PUMP SERIES SHF 8 RISK CLASS TYPE RATED OH4n OH4m HH1n HH1m SHF.. POWER Q = DELIVERY l/min ELECTRIC PUMP m 3 /h PUMP kw NPSHr [METRES COLUMN OF WATER] 8-16/ /D169 1 x 11 2,3 2, 2,7 3, 3,2,9 6, 8-16/1 8-16/D177 1 x 1 2,3 2, 2,7 2,9 3, 4,3 4,6, 8-16/ /D186 1 x 18, 2,3 2, 2,7 2,9 3, 4,3 4,6, 6,1 6,8 8-2/22 8-2/D198 1 x 22 2,2 2,4 2,7 2,8 3,9 4,1 4,6 4,9 8-2/3 8-2/D21 1 x 3 2,2 2,4 2,6 2,8 3,7 3,8 4,2 4,4 4,7, 8-2/37 8-2/D226 1 x 37 2, 2,2 2,4 2,6 2,8 3,7 3,8 4,2 4,4 4,7, 6, 8-2/4 8-2/D237 1 x 4 1,9 2,2 2,4 2,6 3,6 3,7 4,2 4,6 8-2/ 8-2/D22 1 x 1,9 2,2 2,4 2,6 3,6 3,7 4,2 4,6,1 8-2/7 8-2/D27 1 x 7 1,9 2,2 2,4 2,6 3,6 3,7 4,2 4,6,1 6, The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-shf8-2p_NPSHr-en_a_th OHn, OHm, HHn, HHm = risk class value referred to the required rated and maximum capacity (Tab.6 para 7.3.1, Tab.7 para EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1

106 GEN..D/SHF 32-8 BOOSTER SETS ELECTRICAL DATA A TABLE AT Hz SERVICE ELECTRIC JOCKEY CURRENT (*) PUMP PUMP ABSORBED SET 3 X 4 V 1 x 23V 3x4 TYPE NOMINAL 1x23V 3x4V SHF.. POWER ELECTRIC PUMP Pn In TYPE Pn In In GEN..D GEN..1D GEN..1D GEN..11D PUMP kw A kw A A A A A A 32-12/ /D121,7 2,2 SV26,7, 2,2 3 8,,2 7, / /D136 1,1 2,61 SV26,7, 2,2 3 8,,61 7, / /D1 1, 3,4 SV26,7, 2,2 3 8, 6,4 8, / /D168 2,2,3 SV26,7, 2,2 3 8, 8,3 1,1 32-2/3 32-2/D188 3,91 SV26,7, 2,2 3 8, 8,91 1,9 32-2/4 32-2/D24 4 7,73 SV29 1,1 6,82 2,61 3 9,82 1,7 13,3 32-2/ 32-2/D222, 1,8 SV29 1,1 6,82 2,61 3 9,82 13,8 16, /7 32-2/D242 7, 14 SV29 1,1 6,82 2,61 3 9, , / /D SV29 1,1 6,82 2,61 3 9, , / /D112 1,1 2,61 SV26,7, 2,2 3 8,,61 7, /1 4-12/D126 1, 3,4 SV26,7, 2,2 3 8, 6,4 8, / /D143 2,2,3 SV26,7, 2,2 3 8, 8,3 1,1 4-16/3 4-16/D19 3,91 SV26,7, 2,2 3 8, 8,91 1,9 4-16/4 4-16/D ,73 SV26,7, 2,2 3 8, 1,7 12,8 4-2/ 4-2/D19, 1,8 SV26,7, 2,2 3 8, 13,8 1,82 4-2/7 4-2/D29 7, 14 SV29 1,1 6,82 2,61 3 9, ,61 4-2/11A 4-2/D SV29 1,1 6,82 2,61 3 9, ,6 4-2/11 4-2/D SV29 1,1 6,82 2,61 3 9, ,6 4-2/1 4-2/D SV29 1,1 6,82 2,61 3 9, ,6-12/22-12/D119 2,2,3 SV26,7, 2,2 3 8, 8,3 1,1-12/3-12/D13 3,91 SV26,7, 2,2 3 8, 8,91 1,9-12/4-12/D ,73 SV26,7, 2,2 3 8, 1,7 12,8-16/ -16/D18, 1,8 SV26,7, 2,2 3 8, 13,8 1,82-16/7-16/D174 7, 14 SV26,7, 2,2 3 8, 17 19,2-2/11A -2/D SV29 1,1 6,82 2,61 3 9, ,6-2/11-2/D SV29 1,1 6,82 2,61 3 9, ,6-2/1-2/D SV29 1,1 6,82 2,61 3 9, ,6-2/18-2/D237 18, 33,2 SV29 1,1 6,82 2,61 3 9,82 36,2 38,8-2/22-2/D ,7 SV29 1,1 6,82 2,61 3 9,82 41,7 44,3 6-16/4 6-16/D ,73 SV26,7, 2,2 3 8, 1,73 12,8 6-16/ 6-16/D129, 1,8 SV26,7, 2,2 3 8, 13,8 1, /7 6-16/D137 7, 14 SV26,7, 2,2 3 8, 17 19, 6-16/11A 6-16/D SV26,7, 2,2 3 8, 23 2, 6-16/ /D SV26,7, 2,2 3 8, 23 2, 6-2/1 6-2/D SV29 1,1 6,82 2,61 3 9, ,6 6-2/18 6-2/D23 18, 33,2 SV29 1,1 6,82 2,61 3 9,82 36,2 38,8 6-2/22 6-2/D ,7 SV29 1,1 6,82 2,61 3 9,82 41,7 44,3 6-2/3 6-2/D SV29 1,1 6,82 2,61 3 9,82 7 9,6 6-2/37 6-2/D SV212 1, 8,9 3,4 3 11, , 8-16/ /D SV47 1,1 6,82 2,61 3 9, ,6 8-16/1 8-16/D SV47 1,1 6,82 2,61 3 9, ,6 8-16/ /D186 18, 33,2 SV47 1,1 6,82 2,61 3 9,82 36,2 38,8 8-2/22 8-2/D ,7 SV47 1,1 6,82 2,61 3 9,82 41,7 44,3 8-2/3 8-2/D SV49 1, 8,9 3,4 3 11,9 7 6, 8-2/37 8-2/D SV49 1, 8,9 3,4 3 11, , 8-2/4 8-2/D SV49 1, 8,9 3,4 3 11, , 8-2/ 8-2/D22 99 SV413 2,2 12,2,3 3 1, , 8-2/7 8-2/D SV413 2,2 12,2,3 3 1, , ENMTP-SHF_2p-en_b_te (*)The current indicated is the maximum current absorbed. At the set 3x4V three phase power supply GEN..1D e GEN..11D to add the control panel corrent of the engine pump (GEN..D), 1x23V single phase The sets GEN..1D have the electric jockey pump 1x23V single phase power supply. 16

107 Fire-fighting booster sets EN 1284 DSHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 22 m 3 /h. Head up to 1 m. Panel supply power voltage: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Diesel engine with battery start. Diesel engine service pump in horizontal design: - SHF series. Maximum running pressure: 12 bar. 17

108 DSHF 32-8 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

109 DSHF 32-8 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 D.. DNA DNM A B C E F H H1 H2 SHFE32-12/D121 R 2" SHFE32-12/D136 R 2" SHFE32-16/D1 R 2" SHFE32-16/D168 R 2" SHFE32-2/D188 R 2" SHFE32-2/D24 R 2" SHFE32-2/D222 R 2" SHFE32-2/D242 R 2" SHFE32-2/D26 R 2" SHFE4-12/D SHFE4-12/D SHFE4-12/D SHFE4-16/D SHFE4-16/D SHFE4-2/D SHFE4-2/D SHFE4-2/D SHFE4-2/D SHFE4-2/D SHFE-12/D SHFE-12/D SHFE-12/D SHFE-16/D SHFE-16/D SHFE-2/D SHFE-2/D SHFE-2/D SHFE-2/D SHFE-2/D SHFE6-16/D SHFE6-16/D SHFE6-16/D SHFE6-16/D SHFE6-16/D SHFE6-2/D SHFE6-2/D SHFE6-2/D SHFE6-2/D SHFE6-2/D SHFE8-16/D SHFE8-16/D SHFE8-16/D SHFE8-2/D SHFE8-2/D SHFE8-2/D SHFE8-2/D SHFE8-2/D SHFE8-2/D Dimensions in mm. Tolerance ± 1 mm. d_shfe-en_d_td 19

110 11

111 Fire-fighting booster sets EN 1284 GEN..D/SHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 22 m 3 /h. Head up to 1 m. Panel supply power voltage: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Diesel engine with battery start. Diesel engine service pump in horizontal design: - SHF series. Maximum running pressure: 12 bar. 111

112 GEN..D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

113 GEN..D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D DRW N DNA DNM A B D E G N P Q SHF32-12/D121 1 R 2" R 1"1/ SHF32-12/D136 1 R 2" R 1"1/ SHF32-16/D1 1 R 2" R 1"1/ SHF32-16/D168 1 R 2" R 1"1/ SHF32-2/D188 1 R 2" R 1"1/ SHF32-2/D24 1 R 2" R 1"1/ SHF32-2/D222 1 R 2" R 1"1/ SHF32-2/D242 1 R 2" R 1"1/ SHF32-2/D26 1 R 2" R 1"1/ SHF4-12/D SHF4-12/D SHF4-12/D SHF4-16/D SHF4-16/D SHF4-2/D SHF4-2/D SHF4-2/D SHF4-2/D SHF4-2/D SHF-12/D SHF-12/D SHF-12/D SHF-16/D SHF-16/D SHF-2/D SHF-2/D SHF-2/D SHF-2/D SHF-2/D SHF6-16/D SHF6-16/D SHF6-16/D SHF6-16/D SHF6-16/D SHF6-2/D SHF6-2/D SHF6-2/D SHF6-2/D SHF6-2/D SHF8-16/D SHF8-16/D SHF8-16/D SHF8-2/D SHF8-2/D SHF8-2/D SHF8-2/D SHF8-2/D SHF8-2/D Dimensions in mm. Tolerance ± 1 mm gend_shf-en_e_td 113

114 114

115 Fire-fighting booster sets EN 1284 GEN..1D/SHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 22 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 1 x 23V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Electric motor start : - Direct start for powers up to 22 kw included for electric pump. Diesel engine with battery start. Service pump in horizontal design: - SHF series. Electric jockey pump with vertical axis: - SV Series (motor protection grade IP). Maximum running pressure: 12 bar. 11

116 GEN..1D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

117 GEN..1D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW DNA DNP DNM A A1 B C D F G H I L N P Q N SHF32-12/D121 1 R 2" Rp 1" R 1"1/ SHF32-12/D136 1 R 2" Rp 1" R 1"1/ SHF32-16/D1 1 R 2" Rp 1" R 1"1/ SHF32-16/D168 1 R 2" Rp 1" R 1"1/ SHF32-2/D188 1 R 2" Rp 1" R 1"1/ SHF32-2/D24 1 R 2" Rp 1" R 1"1/ SHF32-2/D222 1 R 2" Rp 1" R 1"1/ SHF32-2/D242 1 R 2" Rp 1" R 1"1/ SHF32-2/D26 1 R 2" Rp 1" R 1"1/ SHF4-12/D Rp 1" SHF4-12/D Rp 1" SHF4-12/D Rp 1" SHF4-16/D Rp 1" SHF4-16/D Rp 1" SHF4-2/D Rp 1" SHF4-2/D Rp 1" SHF4-2/D Rp 1" SHF4-2/D Rp 1" SHF4-2/D Rp 1" SHF-12/D Rp 1" SHF-12/D Rp 1" SHF-12/D Rp 1" SHF-16/D Rp 1" SHF-16/D Rp 1" SHF-2/D Rp 1" SHF-2/D Rp 1" SHF-2/D Rp 1" SHF-2/D Rp 1" SHF-2/D2 2 6 Rp 1" SHF6-16/D Rp 1" SHF6-16/D Rp 1" SHF6-16/D Rp 1" SHF6-16/D Rp 1" SHF6-16/D Rp 1" SHF6-2/D Rp 1" SHF6-2/D Rp 1" SHF6-2/D Rp 1" SHF6-2/D Rp 1" SHF6-2/D2 2 8 Rp 1" SHF8-16/D Rp 1" 1/ SHF8-16/D Rp 1" 1/ SHF8-16/D Rp 1" 1/ SHF8-2/D Rp 1" 1/ SHF8-2/D Rp 1" 1/ SHF8-2/D Rp 1" 1/ SHF8-2/D Rp 1" 1/ SHF8-2/D Rp 1" 1/ SHF8-2/D Rp 1" 1/ * * Wall mounted control panel. gen1d_shf-en_e_td Dimensions in mm. Tolerance ± 1 mm. 117

118 118

119 Fire-fighting booster sets EN 1284 Serie GEN..1D/SHF MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 44 m 3 /h. Head up to1 m. Panel supply power voltage: - Electric pump: 3 x 4V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Electric motor start : - Direct start for powers up to 22 kw included for pump (GEND...). - Star/delta start for higher powers (GENY... set). Diesel engine with battery start. Service pump in horizontal design: - SHF series (IP electric motor protection). Maximum running pressure: 12 bar. 119

120 GEN..1D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

121 GEN..1D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW DNA DNM A A1 B C D G H I L N P Q N SHF32-12/7/D121 1 R 2" R 2" SHF32-12/11/D136 1 R 2" R 2" SHF32-16/1/D1 1 R 2" R 2" SHF32-16/22/D168 1 R 2" R 2" SHF32-2/3/D188 1 R 2" R 2" SHF32-2/4/D24 1 R 2" R 2" SHF32-2//D222 1 R 2" R 2" SHF32-2/7/D242 1 R 2" R 2" SHF32-2/11/D26 1 R 2" R 2" SHF4-12/11/D SHF4-12/1/D SHF4-12/22/D SHF4-16/3/D SHF4-16/4/D SHF4-2//D SHF4-2/7/D SHF4-2/11A/D SHF4-2/11/D SHF4-2/1/D SHF-12/22/D SHF-12/3/D SHF-12/4/D SHF-16//D SHF-16/7/D SHF-2/11A/D SHF-2/11/D SHF-2/1/D SHF-2/18/D SHF-2/22/D SHF6-16/4/D SHF6-16//D SHF6-16/7/D SHF6-16/11A/D SHF6-16/11/D SHF6-2/1/D SHF6-2/18/D SHF6-2/22/D SHF6-2/3/D SHF6-2/37/D SHF8-16/11/D SHF8-16/1/D SHF8-16/18/D SHF8-2/22/D SHF8-2/3/D SHF8-2/37/D SHF8-2/4/D SHF8-2//D SHF8-2/7/D * Dimensions in mm. Tolerance ± 1 mm. gen1d_shf-en_d_td 121

122 122

123 Fire-fighting booster sets EN 1284 GEN..11D/SHF Series MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. SPECIFICATIONS Flow up to 44 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 3 x 4V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Electric motor start : - Direct start for powers up to 22 kw included for pump (GEND...). - Star/delta start for higher powers (GENY... set). Diesel engine with battery start. Service pump in horizontal design: - SHF series (IP electric motor protection). Electric jockey pump with vertical axis: - SV Series (motor protection grade IP). Maximum running pressure: 12 bar. 123

124 GEN..11D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages

125 GEN..11D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..11D DRW DNA DNP DNM A A1 B C D F G H I I1 L N P Q N SHF32-12/7/D121 1 R 2" Rp 1" R 2" SHF32-12/11/D136 1 R 2" Rp 1" R 2" SHF32-16/1/D1 1 R 2" Rp 1" R 2" SHF32-16/22/D168 1 R 2" Rp 1" R 2" SHF32-2/3/D188 1 R 2" Rp 1" R 2" SHF32-2/4/D24 1 R 2" Rp 1" R 2" SHF32-2//D222 1 R 2" Rp 1" R 2" SHF32-2/7/D242 1 R 2" Rp 1" R 2" SHF32-2/11/D26 1 R 2" Rp 1" R 2" SHF4-12/11/D Rp 1" SHF4-12/1/D Rp 1" SHF4-12/22/D Rp 1" SHF4-16/3/D Rp 1" SHF4-16/4/D Rp 1" SHF4-2//D Rp 1" SHF4-2/7/D Rp 1" SHF4-2/11A/D Rp 1" SHF4-2/11/D Rp 1" SHF4-2/1/D Rp 1" SHF-12/22/D Rp 1" SHF-12/3/D Rp 1" SHF-12/4/D Rp 1" SHF-16//D Rp 1" SHF-16/7/D Rp 1" SHF-2/11A/D Rp 1" SHF-2/11/D Rp 1" SHF-2/1/D Rp 1" SHF-2/18/D Rp 1" SHF-2/22/D2 2 6 Rp 1" SHF6-16/4/D Rp 1" SHF6-16//D Rp 1" SHF6-16/7/D Rp 1" SHF6-16/11A/D Rp 1" SHF6-16/11/D Rp 1" SHF6-2/1/D Rp 1" SHF6-2/18/D Rp 1" SHF6-2/22/D Rp 1" SHF6-2/3/D Rp 1" SHF6-2/37/D2 2 8 Rp 1" SHF8-16/11/D Rp 1" 1/ SHF8-16/1/D Rp 1" 1/ SHF8-16/18/D Rp 1" 1/ SHF8-2/22/D Rp 1" 1/ SHF8-2/3/D Rp 1" 1/ SHF8-2/37/D Rp 1" 1/ SHF8-2/4/D Rp 1" 1/ SHF8-2//D Rp 1" 1/ SHF8-2/7/D Rp 1" 1/ * * Wall mounted control panel. gen11d_shf-en_f_td Dimensions in mm. Tolerance ± 1 mm. 12

126 126

127 GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm],2,8,2, Q [US gpm],2,8,2,6,1,1,4,1,1,4,,2,,2, 6,, 8, /1 φ / /1 Ø φ Q [m 3 /h] Q [l/min] 7617_A_CH Q [m 3 3 /h] Q [l/min] 7618_A_CH SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm],2,8,2, Q [US gpm],2,8,2,6,1,1,4,1,1,4,,2,,2, 8, 2, 8, / φ /3 φ /4 φ /1 Ø /11 φ /7 φ /1 Ø Q [m 3 3 /h] Q [l/min] 7619_A_CH Q [m 3 3 /h] Q [l/min] 762_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 127

128 GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A 1 1 Q [Imp gpm] 1 1 Q [Imp gpm] 1 1 2,2,2 Q [US gpm],8, Q [US gpm],2,8,2,6,1,1,4,1,1,4,,2,,2, 8, 2, 8, Q [m 3 /h] Q 8 [l/min] 7621_A_CH Q [m 3 /h] Q 8 [l/min] 7622_A_CH SH [rpm] ISO Annex A SH [rpm] ISO Annex A 1 1 Q [Imp gpm] Q [Imp gpm] Q [US gpm],2,8,2, Q [US 2gpm],2,8,2,6,1,1,4,1,1,4,,2,,2, 8, 2, 8, /11A φ /1 Ø /1 φ /11 φ Q [m 3 /h] Q 8 [l/min] 7623_A_CH Q [m 3 6 /h] Q [l/min] _A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 128

129 GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm],2,8,2, Q [US gpm],2,8,2,6,1,1,4,1,1,4,,2,,2, 8, 2, 1, /22 φ /4 φ /3 φ /1 Ø / φ /1-16/7 Ø 178 φ Q [m1 3 /h] Q 16 [l/min] 762_A_CH Q [m1 3 /h] Q 16 [l/min] 7626_A_CH SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US gpm],3,2,8,2,8,2,6,2,6,1,1,4,4,1,1,,2,,2, 1,, 1, /11A φ /11 φ /1 Ø /1 φ /1 Ø /22 φ 2-2/18 φ Q [m1 3 /h] Q 16 [l/min] 7627_A_CH Q [m1 3 /h] Q 16 [l/min] 7628_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 129

130 GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [US 6 gpm], Q [Imp gpm] Q [US 6 gpm],4,2,8,3 1,2 1,,2,6,8,1,4,2,6,1,,2,1,4,2, 1,, 1, /22 φ /4 φ /3 φ /1 Ø /1 Ø /11 φ /11A φ Q [m14 3 /h] Q 22 [l/min] 7629_A_CH Q [m14 3 /h] Q 22 [l/min] 763_A_CH SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 6 gpm], Q [US gpm] 7,6 1,2,,3 1, 1,,8,4,2,6,3 1,,1,4,2,,2,1, 1,, 1, /1 φ /1 Ø /3 φ /37 φ /1 Ø /22 φ /18 φ Q [m14 3 /h] Q 22 [l/min] 7631_A_CH Q [m16 3 /h] Q [l/min] 7632_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 13

131 GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US gpm],4 1,2,3 1,,3 1,,8,2,6,2 1,,1,4,1,,2, 1,, 1, /1 φ 169x /22 φ /1 Ø /37 φ /3 6-16/1 φ 21 Ø /18 φ /1 φ Q [m2 3 /h] Q 4 [l/min] 7633_A_CH Q [m3 3 /h] Q [l/min] 7634_A_CH SH [rpm] ISO Annex A Q [Imp gpm] Q [US gpm],4 1,2,3 1,,8,2,6,1,4,2, 1, /1 Ø Q [m2 3 /h] Q [l/min] 763_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 131

132 GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [US gpm], Q [Imp gpm] Q [US gpm],6,,3 1, 1,,4,2,3 1,,,2,1,,1, 6,, 8, /1 φ / /1 Ø φ Q [m 3 /h] Q [l/min] 76497_A_CH Q [m 3 3 /h] Q [l/min] 76498_A_CH SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [US gpm], Q [Imp gpm] Q [US gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 8, 2, 8, / φ /3 φ /4 φ /1 Ø /11 φ /7 φ /1 Ø Q [m 3 3 /h] Q [l/min] 76499_A_CH Q [m 3 3 /h] Q [l/min] 76_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 132

133 GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A 1 1 Q [Imp gpm] 1 1 Q [Imp gpm] 1 1 2,6 Q [US gpm] Q [US gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 8, 2, 8, Q [m 3 /h] Q 8 [l/min] 761_A_CH Q [m 3 /h] Q 8 [l/min] 762_A_CH SH [rpm] ISO Annex A SH [rpm] ISO Annex A 1 1 Q [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US 2gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 8, 2, 8, /11A φ /1 Ø /1 φ /11 φ Q [m 3 /h] Q 8 [l/min] 763_A_CH Q [m 3 6 /h] Q [l/min] 1 764_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 133

134 GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 8, 2, 1, /22 φ /4 φ /3 φ /1 Ø / φ /1-16/7 Ø 178 φ Q [m1 3 /h] Q 16 [l/min] 76_A_CH Q [m1 3 /h] Q 16 [l/min] 766_A_CH SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, /11A φ /11 φ /1 Ø /1 φ /1 Ø /22 φ 2-2/18 φ Q [m1 3 /h] Q 16 [l/min] 767_A_CH Q [m1 3 /h] Q 16 [l/min] 768_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 134

135 GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [US 6 gpm], Q [Imp gpm] Q [US 6 gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, /22 φ /4 φ /3 φ /1 Ø /1 Ø /11 φ /11A φ Q [m14 3 /h] Q 22 [l/min] 761_A_CH Q [m14 3 /h] Q 22 [l/min] 7611_A_CH SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US 6 gpm], Q [US gpm] 7,6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, /1 φ /1 Ø /3 φ /37 φ /1 Ø /22 φ /18 φ Q [m14 3 /h] Q 22 [l/min] 7612_A_CH Q [m16 3 /h] Q [l/min] 7613_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 13

136 GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH [rpm] ISO Annex A SH [rpm] ISO Annex A Q [Imp gpm] Q [Imp gpm] Q [US gpm], Q [US gpm],6,, 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, /1 φ 169x /22 φ /1 Ø /37 φ /3 6-16/1 φ 21 Ø /18 φ /1 φ Q [m2 3 /h] Q 4 [l/min] 7614_A_CH Q [m3 3 /h] Q [l/min] 761_A_CH SH [rpm] ISO Annex A Q [Imp gpm] Q [US gpm],6, 1,,4,3 1,,2,,1, 1, /1 Ø Q [m2 3 /h] Q [l/min] 7616_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 136

137 ACCESSORIES SORIES 137

138 DIAPHRAGM TANKS The booster sets are ready for installation, directly on the manifold, of 24-litre diaphragm tanks, one for each pump. The sets are also equipped with caps to close off the unused couplings. Larger tanks can also be connected to the unused end of the discharge manifold. For proper sizing of the tank please refer to the technical appendix. Kit featuring the following accessories are available on request: diaphragm tank; on-off ball valve; operating instructions; packaging. DIAPHRAGM TANK KIT Volume PN DIMENSIONS (mm) Materials Litres bar ø A B Valve Diaphragm Vessel Valve " FF EPDM Painted steel Nickel-plated brass " FF EPDM Painted steel Nickel-plated brass " FF EPDM Painted steel Nickel-plated brass " FF EPDM Painted steel Nickel-plated brass " FF Butyl Stainless steel AISI 316 Stainless steel COUNTERFLANGE KIT gcom-vmb_en_b_td Counterflange coupling kits made of zinc-plated or stainless steel are available on request. The counterflange kits are equipped with: - N. 2 flanges. - gasket and bolts/screws. THREADED COUNTERFLANGES KIT DIMENSIONS (mm) HOLES TYPE DN ø C ø A B ø D H ø F N PN 2" Rp " ½ 6 Rp 2 ½ " 8 Rp Gcom-ctf-tonde-f-en_a_td WELD-ON COUNTERFLANGES KIT DIMENSIONS (mm) HOLES TYPE DN ø C ø A B ø D ø F N PN 2" "1/ " " " , " 1 17, " 2 221, " 2 276, " 3 327, Gcom-ctf-tonde-s-en_c_td 138

139 ACCESSORIES SORIES FOR BOOSTER SETS SUCTION SIDE KIT The EN 1284 fire-fighting booster sets are supplied without valves and stubs on the suction side of the service pump and can be completed with suitable kits that depend on legal standards. These requirements are expressed by EN 1284 (chapter 1. and chapter 1.6) and are connected with the maximum speed value of the water in the pipes, their minimum section and type of installation - suction lift or positive suction head. To provide for one suction kit for each duty pump. The suction side kit are equipped with: - Anti-vibration joint to attach to the pump inlet. - Eccentric cone or flanged stub pipe. - Vacuum pressure gauge. - On/off butterfly valve with lever handle for diameters up to DN1, butterfly valve with handwheel and reduction manual gear for DN12 and higher. Device for monitoring ON/OFF status included. Electrical connections by customer. (Valve lock kit available on request). - Weld-on flange. The following table summarises the pump type installed on the fire-fighting sets and the kit that corresponds to the installation type. 139

140 GEN../ SERIES OF FIRE-FIGHTING BOOSTER SETS SUCTION SIDE KIT DIMENSIONS TABLE SUCTION KIT TYPE DNS PN DIMENSIONS DNA PN L (mm) H (mm) X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Dimensions in mm. Tolerance ± 1 mm. kit-asp-en_b_td 14

141 GEN../FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS SUCTION SIDE KIT DIMENSIONS TABLE SUCTION LIFT POSITIVE SUCTION HEAD RISK SUCTION RISK SUCTION RISK SUCTION RISK SUCTION PUMP CLASS * KIT CLASS * KIT CLASS * KIT CLASS * KIT TYPE TYPE TYPE TYPE FHF 32-12/7 LH 6 X - - LH 8 X - - FHF 32-12/11 LH 6 X - - LH 8 X - - FHF 32-16/1 LH 6 X - - LH 8 X - - FHF 32-16/22 LH 6 X - - LH 8 X - - FHF 32-2/3 LH 6 X - - LH 8 X - - FHF 32-2/4 LH 6 X - - LH 8 X - - FHF 4-12/11 OH1 8 X OH1 1 X FHF 4-12/1 OH1 8 X OH1 1 X FHF 4-12/22 OH1 8 X OH1 1 X FHF 4-16/3 OH1 8 X OH1 1 X FHF 4-16/4 OH1 8 X OH1 1 X FHF 4-2/ OH1 8 X OH1 1 X FHF 4-2/7 OH1 8 X OH1 1 X FHF 4-2/11A OH1 8 X OH1 1 X FHF 4-2/11 OH1 8 X OH1 1 X FHF 4-2/1 OH1 8 X OH1 1 X FHF -12/22 OH2 1 X OH2 12 X FHF -12/3 OH2 1 X OH2 12 X FHF -12/4 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -16/ OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -16/7 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/11A OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/11 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/1 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/18 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/22 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF 6-12/4 OH3 12 X OH3 1 X FHF 6-12/ OH3 12 X OH3 1 X FHF 6-12/7 OH3 12 X OH3 1 X FHF 6-16/11A OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-16/11 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-16/1 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/1 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/18 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/22 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/22 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/3 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/37 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 8-16/1 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-16/18 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/22 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/3 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/37 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/4 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/ HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 * For the risk classes refer to para 6, UNI EN1284. kit-asp-fhf-en_b_td - the pumps must be chosen according to the performance levels indicated in Tab. 6 para 7.3.1, Tab.7 para and the classes of risk. - some pump models can satisfy the conditions of one or more classes of risk. - always check the correct selection of the pump depending on the performance level of the set. ** Insert the mm minimal thickness under the GEN1 fire-fighting booster sets only. 141

142 GEN../FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS SUCTION SIDE KIT DIMENSIONS TABLE SUCTION LIFT POSITIVE SUCTION HEAD RISK SUCTION RISK SUCTION RISK SUCTION RISK SUCTION PUMP CLASS * KIT CLASS * KIT CLASS * KIT CLASS * KIT TYPE TYPE TYPE TYPE FHF 1-16/18 HH3 2 X 12 HH2 2 X 12 HH3 2 X 12 HH2 2 X 12 FHF 1-16/22 HH4 2 X 12 HH3 2 X 12 HH4 3 X 12** HH3 2 X 12 FHF 1-16/3 HH4 2 X 12 HH3 2 X 12 HH4 3 X 12** HH3 2 X 12 FHF 1-2/18 HH3 2 X 12** HH2 2 X 12** HH3 2 X 12** HH2 2 X 12** FHF 1-2/3 HH3 2 X 12** HH2 2 X 12** HH3 2 X 12** HH2 2 X 12** FHF 1-2/37 HH4 2 X 12** HH3 2 X 12** HH4 3 X 12** HH3 2 X 12** FHF 1-2/4 HH4 2 X 12 HH3 2 X 12 HH4 3 X 12** HH3 2 X 12 FHF 1-2/3 HH3 2 X 12 HH2 2 X 12 HH3 2 X 12 HH2 2 X 12 FHF 1-2/4 HH4 2 X 12 HH3 2 X 12 HH4 3 X 12** HH3 2 X 12 FHF 1-2/ HH4 2 X 12 HH3 2 X 12 HH4 3 X 12 HH3 2 X 12 FHF 1-2/7 HH 3 X 12 HH4 2 X 12 HH 3 X 12 HH4 3 X 12 FHF 1-2/9 HH6 3 X 12 HH 3 X 12 HH6 3 X 12 HH 3 X 12 FHF 12-2/3 HH7 3 X 1 HH6 3 X 1 HH7 3 X 1 HH6 3 X 1 FHF 12-2/4 HH9 3 X 1 HH8 3 X 1 HH9 4 X 1** HH8 3 X 1** FHF 12-2/ HH1 3 X 1** HH9 3 X 1 HH1 4 X 1** HH9 4 X 1** FHF 12-27/7 HH1 3 X 1 HH9 3 X 1 HH1 4 X 1 HH9 4 X 1 FHF 12-27/9 HH1 3 X 1 HH9 3 X 1 HH1 4 X 1 HH9 4 X 1 FHF 12-27/11 HH1 3 X 1 HH9 3 X 1 HH1 4 X 1 HH9 4 X 1 FHF 12-27/132 HH1 3 X 1 HH9 3 X 1 HH1 4 X 1 HH9 4 X 1 * For the risk classes refer to para 6, UNI EN1284. kit-asp-fhf1-en_a_td - the pumps must be chosen according to the performance levels indicated in Tab. 6 para 7.3.1, Tab. 7 para and the classes of risk. - some pump models can satisfy the conditions of one or more classes of risk. - always check the correct selection of the pump depending on the performance level of the set. ** Insert the mm minimal thickness under the GEN1 fire-fighting booster sets only. 142

143 GEN../SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS SUCTION SIDE KIT DIMENSIONS TABLE SUCTION LIFT POSITIVE SUCTION HEAD RISK SUCTION RISK SUCTION RISK SUCTION RISK SUCTION PUMP CLASS * KIT CLASS * KIT CLASS * KIT CLASS * KIT TYPE TYPE TYPE TYPE SHF 32-12/7 LH 6 X - - LH 8 X - - SHF 32-12/11 LH 6 X - - LH 8 X - - SHF 32-16/1 LH 6 X - - LH 8 X - - SHF 32-16/22 LH 6 X - - LH 8 X - - SHF 32-2/3 LH 6 X - - LH 8 X - - SHF 32-2/4 LH 6 X - - LH 8 X - - SHF 32-2/ LH 6 X - - LH 8 X - - SHF 32-2/7 LH 6 X - - LH 8 X - - SHF 32-2/11 LH 6 X - - LH 8 X - - SHF 4-12/11 OH1 8 X OH1 1 X SHF 4-12/1 OH1 8 X OH1 1 X SHF 4-12/22 OH1 8 X OH1 1 X SHF 4-16/3 OH1 8 X OH1 1 X SHF 4-16/4 OH1 8 X OH1 1 X SHF 4-2/ OH1 8 X OH1 1 X SHF 4-2/7 OH1 8 X OH1 1 X SHF 4-2/11A OH1 8 X OH1 1 X SHF 4-2/11 OH1 8 X OH1 1 X SHF 4-2/1 OH1 8 X OH1 1 X SHF -12/22 OH2 1 X OH2 12 X SHF -12/3 OH2 1 X OH2 12 X SHF -12/4 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -16/ OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -16/7 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -2/11A OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -2/11 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -2/1 OH2 1 X OH2 12 X SHF -2/18 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -2/22 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF 6-16/4 OH3 12 X OH3 1 X SHF 6-16/ OH3 12 X OH3 1 X SHF 6-16/7 OH3 12 X OH3 1 X SHF 6-16/11A OH3 12 X OH3 1 X SHF 6-16/11 OH3 12 X OH3 1 X SHF 6-2/1 OH3 12 X OH3 1 X SHF 6-2/18 OH3 12 X OH3 1 X SHF 6-2/22 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 SHF 6-2/3 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 SHF 6-2/37 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 SHF 8-16/11 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-16/1 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-16/18 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/22 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/3 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/37 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/4 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/ HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/7 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 * For the risk classes refer to para 6, UNI EN1284. kit-asp-shf-en_a_td - the pumps must be chosen according to the performance levels indicated in Tab. 6 para 7.3.1, Tab. 7 para and the classes of risk. - some pump models can satisfy the conditions of one or more classes of risk. - always check the correct selection of the pump depending on the performance level of the set. ** Insert the mm minimal thickness under the GEN1 fire-fighting booster sets only. 143

144 - + ACCORDING TO EN1284 LAMPS TEST PROVA LAMPADE Plant Type: Tipo impianto: POWER ON PRESENZA TENSIONE UNDER THRESHOLD SOTTO SOGLIA PUMP ON POMPA IN MARCIA INTERRUPTED LINES! 3 LINEE INTERROTTE INCREASE SHIFT ENTER DECREASE / MENU' BUZZER SWITCH OFF TACITAZIONE SIRENA V - + L1/ A A - + L1/ A SPRINKLER DRAINAGE PUMPS ROOM FAULT PUMP L2 L1 L3 JOCKEY PUMP POMPA COMPENSAZIONE Voltage 23 V - -6 Hz Code N Circ. N Battery 12 V 2,3 Ah Buzzer 12Vcc 9mA 7dB(A),2 A IP OVERLOAD SOVRACCARICO SPRINKLER PUMPS ROOM SPRINKLER SALA POMPE PUMP SET ON DEMAND RICHIESTA DI AVVIAMENTO SELECTOR NOT IN AUT. FUNCTION SELETTORE NON IN AUT. V - + L2/ B A L2/ + B L2 PHASE SEQUENCE FAILURE ERRATA SEQUENZA FASE L1 L3 MINIMUM FUEL LEVEL MIN. LIVELLO COMBUSTIBILE!! 1 2 V L3 L3 N.P. START FAILURE MANCATO AVVIAMENTO SWITCHBOARD FAILURE GUASTO QUADRO 1 ELECTRIC PUMP / POMPA ELETTRICA!! OFF OFF 1 2 DIESEL PUMP / MOTOPOMPA MINIMUM LEVEL SUCTION TANK 1 MINIMO LIVELLO VASCA ASPIRAZIONE MINIMUM LEVEL PRIMING TANK 2 MINIMO LIVELLO VASCA ADESCAMENTO! PARTIALLY OPENED SUCTION VALVE OFF VALVOLA IN ASPIRAZIONE NON 1 COMPLETAMENTE APERTA! PARTIALLY OPENED DISCHARGE VALVE OFF VALVOLA IN MANDATA NON 2 COMPLETAMENTE APERTA ALARMS CONTROL ELECTRICAL PANEL Electric panel for remote status and alarm monitoring of one or two pumps installed in GEN fire-fighting booster sets, according to EN1284. In the electric service pump mode, the following conditions are visualised: - Motor powered. - Pump start-up request. - Pump running - Failure to start. Additionally: minimum suction tank level, minimum priming tank level, on-off valve on suction and discharge side not fully open. The valves are complete with status monitor. In the diesel engine service pump mode, the following conditions are visualised, as required by EN1284: - Switch on diesel engine pump control panel in non-automatic position. - Diesel engine ails to start after 6 attempts. - Pump running - Controller fault. Additionally: minimum fuel or suction tank level, minimum priming tank level, on-off valve on suction and discharge side not fully open. The valves are complete with status monitor. All the above conditions, required by EN1284, are visualised with signal LED s and buzzers. A buzzer alarm reset button and LED tester button are included. The control unit is also fitted out to signal the following general alarms, if present: - General alarm for incorrect electrical connection in the exchange contacts of: flow meter circuit valve, discharge pump, jockey pump status. - Fault in electrical connection in the exchange contact relative to panel 1 (electric pump/diesel engine pump) - Fault in electrical connection in the exchange contact relative to panel 2 (electric pump/diesel engine pump) - Jockey pump overload (*). - Jockey pump running(*) - Discharge pump overload (*). - Battery voltage low. - Communications failure with ModBus system. All the above conditions are visualised with signal LED s and on the display. The customer may decide to enable the buzzer. The panel comprises a plastic casing (IP), battery, battery charger, alarms and pump status display, if connected with 48 serial communication. Fitted to transmit alarms for GSM or PC module. The electric connection between the contacts on the electric alarms control panel and other electric panels is to be seen to by the person installing the equipment. (*) Check that the electric control panel combined with the electric pump is complete with clean contacts for pump running and overload signals. TECHNICAL SPECIFICATIONS 27 DESCRIPTION VALUE Input voltage (single-phase) (1F+N) 23V +/-1%, -6 Hz Absorbed,1A Dimensions 37 x 27 x 16 mm Protection grade IP Battery Hermetic lead Rated battery voltage 12 Vcc Rated battery capacity 2,3 Ah ( uncharged in 2 h) Dimensions of battery 178 x 34 x 66 mm Sound emission levels 7dB Control panel weight 1,kg 1284-qal-en_b_td 37 Type DSRC GA11E+1D! - A! 1 2! 1284_2_D_DD 144

145 FLOW METER KIT The flow meter is supplied as part of the assembly kit. The EN 1284 standard requires the presence of the flow meter for checking the hydraulic performance during the test stage and duration periodic inspections. The suction side kit are equipped with: - Direct reading flow meter. - On/off ball valve for diameters up to 2" inclusive, butterfly valve with lever handle from DN6 to DN1 diameter, butterfly valve with handwheel and reduction manual gear for DN12 diameter and above. Device for monitoring ON/OFF status included. Electrical connections by customer. (Valve lock kit available on request). - Connection piping. The meter is available in various sizes according to the flow of a service pump and suitable for being connected to the offtake of the head manifold. For a correct match, identify the type as shown in the set size tables. The flow meter must be installed, where possible, in a stretch of piping with a steady flow and sufficient back pressure at the discharge outlet. The assembly and the discharge piping towards the tank and discharge outlet are to be seen to by the person installing the equipment. SHAPE A SHAPE B SHAPE C SHAPE D DIMENSIONS (mm) DIMENSIONS (mm) TYPE TYPE DN DNAS SHAPE L H DN DNAS SHAPE L H 32X2P 32 2 A 9 6 1X4P 1 4 B X32P A XP 1 B X4P 32 4 A X6P 1 6 C X2P 4 2 A 1 6 1X8P 1 8 C X32P 4 32 A X D X4P 4 4 A XP 12 B XP 4 A X6P 12 6 C X2P 2 A X8P 12 8 C X32P 32 A X D 34 7 X4P 4 A X D XP A X6P 1 6 C X2P 6 2 B 3 7 1X8P 1 8 C X32P 6 32 B X D X4P 6 4 B X1 1 1 D XP 6 B X2 1 2 D X6P 6 6 C X8P 2 8 C X8P 6 8 C X D X4P 8 4 B X1 2 1 D XP 8 B X2 2 2 D X6P 8 6 C X D X8P 8 8 C X1 2 1 D X D X2 2 2 D _kit_flux-acc-en_a_td 14

146 TABLE OF COMBINATIONS FOR FLOW METER KIT AND FHF SERVICE PUMP SERIES TYPE COMBINATION TYPE COMBINATION FHF.. FLOW METER KIT FHF.. FLOW METER KIT ELECTRIC PUMP GEN.. ELECTRIC PUMP GEN.. PUMP D 1D 1D 11D PUMP D 1D 1D 11D 32-12/ /D119 4X2P 4X2P X2P X2P 6-2/1 6-2/D187 8X8P 8X8P 1X8P 1X8P 32-12/ /D136 4X32P 4X32P X32P X32P 6-2/18 6-2/D198 8X8P 8X8P 1X8P 1X8P 32-16/ /D1 4X32P 4X32P X32P X32P 6-2/22 6-2/D21 8X8P 8X8P 1X8P 1X8P 32-16/ /D164 4X32P 4X32P X32P X32P 6-2/22 6-2/D22 8X8P 8X8P 1X8P 1X8P 32-2/3 32-2/D188 4X32P 4X32P X32P X32P 6-2/3 6-2/D241 8X8P 8X8P 1X8P 1X8P 32-2/4 32-2/D24 4X32P 4X32P X32P X32P 6-2/37 6-2/D28 8X8P 8X8P 1X8P 1X8P 4-12/ /D112 6X4P 6X4P 6X4P 6X4P 8-16/1 8-16/D163 1X8P 1X8P 12X8P 12X8P 4-12/1 4-12/D122 6X4P 6X4P 6X4P 6X4P 8-16/ /D173 1X12 1X12 12X12 12X / /D143 6XP 6XP 6XP 6XP 8-2/22 8-2/D189 1X8P 1X8P 12X8P 12X8P 4-16/3 4-16/D19 6X4P 6X4P 6X4P 6X4P 8-2/3 8-2/D27 1X12 1X12 12X12 12X /4 4-16/D171 6XP 6XP 6XP 6XP 8-2/37 8-2/D22 1X8P 1X8P 12X8P 12X8P 4-2/ 4-2/D19 6X4P 6X4P 6X4P 6X4P 8-2/4 8-2/D238 1X12 1X12 12X12 12X12 4-2/7 4-2/D29 6XP 6XP 6XP 6XP 8-2/ 8-2/D26 1X12 1X12 12X12 12X12 4-2/11A 4-2/D218 6XP 6XP 6XP 6XP 1-16/ /D1 12X12 12X12 1X12 1X12 4-2/11 4-2/D233 6XP 6XP 6XP 6XP 1-16/ /D16 12X12 12X12 1X12 1X12 4-2/1 4-2/D21 6XP 6XP 6XP 6XP 1-16/3 1-16/D18 12X1 12X1 2X1 2X1-12/22-12/D119 6XP 6XP 8XP 8XP 1-2/18 1-2/D168 12X12 12X12 1X12 1X12-12/3-12/D13 6X6P 6X6P 8X6P 8X6P 1-2/3 1-2/D192 12X12 12X12 1X12 1X12-12/4-12/D139 6X6P 6X6P 8X6P 8X6P 1-2/37 1-2/D23 12X12 12X12 1X12 1X12-16/ -16/D18 6X6P 6X6P 8X6P 8X6P 1-2/4 1-2/D213 12X12 12X12 2X12 2X12-16/7-16/D174 6X6P 6X6P 8X6P 8X6P 1-2/3 1-2/D2 12X12 12X12 1X12 1X12-2/11A -2/D197 6X6P 6X6P 8X6P 8X6P 1-2/4 1-2/D221 12X12 12X12 2X12 2X12-2/11-2/D29 6X6P 6X6P 8X6P 8X6P 1-2/ 1-2/D23 12X12 12X12 2X12 2X12-2/1-2/D224 6X6P 6X6P 8X6P 8X6P 1-2/7 1-2/D24 12X1 12X1 2X1 2X1-2/18-2/D237 6X6P 6X6P 8X6P 8X6P 1-2/9 1-2/D267 12X1 12X1 2X1 2X1-2/22-2/D2 6X6P 6X6P 8X6P 8X6P 12-2/3 12-2/D18 1X1 1X1 2X1 2X1 6-12/4 6-12/D121 8X6P 8X6P 1X6P 1X6P 12-2/4 12-2/D26 1X2 1X2 2X2 2X2 6-12/ 6-12/D129 8X6P 8X6P 1X6P 1X6P 12-2/ 12-2/D216 1X2 1X2 2X2 2X2 6-12/7 6-12/D14 8X6P 8X6P 1X6P 1X6P 12-27/ /D224 1X2 1X2 2X2 2X2 6-16/11A 6-16/D161 8X8P 8X8P 1X8P 1X8P 12-27/ /D237 1X2 1X2 2X2 2X2 6-16/ /D168 8X8P 8X8P 1X8P 1X8P 12-27/ /D23 1X2 1X2 2X2 2X2 6-16/1 6-16/D178 8X8P 8X8P 1X8P 1X8P 12-27/ /D266 1X2 1X2 2X2 2X2 1284_kit_flux-fhf_D-11D-en_b_th 146

147 TABLE OF COMBINATIONS FOR FLOW METER KIT AND SHF SERVICE PUMP SERIES TYPE COMBINATION TYPE COMBINATION SHF.. FLOW METER KIT SHF.. FLOW METER KIT ELECTRIC PUMP GEN.. ELECTRIC PUMP GEN.. PUMP D 1D 1D 11D PUMP D 1D 1D 11D 32-12/ /D121 4X32P 4X32P X32P X32P -2/11A -2/D197 6X6P 6X6P 8X6P 8X6P 32-12/ /D136 4X32P 4X32P X32P X32P -2/11-2/D29 6X6P 6X6P 8X6P 8X6P 32-16/ /D1 4X32P 4X32P X32P X32P -2/1-2/D224 6X6P 6X6P 8X6P 8X6P 32-16/ /D168 4X32P 4X32P X32P X32P -2/18-2/D237 6X6P 6X6P 8X6P 8X6P 32-2/3 32-2/D188 4X32P 4X32P X32P X32P -2/22-2/D2 6X6P 6X6P 8X6P 8X6P 32-2/4 32-2/D24 4X32P 4X32P X32P X32P 6-16/4 6-16/D119 8X6P 8X6P 1X6P 1X6P 32-2/ 32-2/D222 4X32P 4X32P X32P X32P 6-16/ 6-16/D129 8X6P 8X6P 1X6P 1X6P 32-2/7 32-2/D242 4X32P 4X32P X32P X32P 6-16/7 6-16/D137 8X6P 8X6P 1X6P 1X6P 32-2/ /D26 4X32P 4X32P X32P X32P 6-16/11A 6-16/D168 8X6P 8X6P 1X6P 1X6P 4-12/ /D112 6X4P 6X4P 6X4P 6X4P 6-16/ /D177 8X6P 8X6P 1X6P 1X6P 4-12/1 4-12/D126 6X4P 6X4P 6X4P 6X4P 6-2/1 6-2/D192 8X6P 8X6P 1X6P 1X6P 4-12/ /D143 6X4P 6X4P 6X4P 6X4P 6-2/18 6-2/D23 8X6P 8X6P 1X6P 1X6P 4-16/3 4-16/D19 6X4P 6X4P 6X4P 6X4P 6-2/22 6-2/D21 8X8P 8X8P 1X8P 1X8P 4-16/4 4-16/D171 6XP 6XP 6XP 6XP 6-2/3 6-2/D24 8X8P 8X8P 1X8P 1X8P 4-2/ 4-2/D19 6XP 6XP 6XP 6XP 6-2/37 6-2/D2 8X8P 8X8P 1X8P 1X8P 4-2/7 4-2/D29 6XP 6XP 6XP 6XP 8-16/ /D169 1X8P 1X8P 12X8P 12X8P 4-2/11A 4-2/D218 6X4P 6X4P 6X4P 6X4P 8-16/1 8-16/D177 1X8P 1X8P 12X8P 12X8P 4-2/11 4-2/D233 6X4P 6X4P 6X4P 6X4P 8-16/ /D186 1X12 1X12 12X12 12X12 4-2/1 4-2/D21 6XP 6XP 6XP 6XP 8-2/22 8-2/D198 1X12 1X12 12X12 12X12-12/22-12/D119 6XP 6XP 8XP 8XP 8-2/3 8-2/D21 1X12 1X12 12X12 12X12-12/3-12/D13 6X6P 6X6P 8X6P 8X6P 8-2/37 8-2/D226 1X12 1X12 12X12 12X12-12/4-12/D139 6X6P 6X6P 8X6P 8X6P 8-2/4 8-2/D237 1X12 1X12 12X12 12X12-16/ -16/D18 6X6P 6X6P 8X6P 8X6P 8-2/ 8-2/D22 1X12 1X12 12X12 12X12-16/7-16/D174 6X6P 6X6P 8X6P 8X6P 8-2/7 8-2/D27 1X12 1X12 12X12 12X _kit_flux-shf_D-11D-en_c_th 147

148 PRIMING TANK The priming tank is used in suction lift installations and carries out the function of maintaining the pump body and suction pipe full of water even if there are leaks through the bottom valve. Each pump must have its own independent priming tank, placed at a higher level than the pump. The tank must be connected to a water source for adding water and keeping it full. The diameter of the connecting pipe to the pump depends on the use class. The return piping for re-circulation can be connected to the tank, which must also provide for discharge if it is too full. A level indicator automatically actions the service pump if the level of the tank drops and is not reintegrated. The hydraulic connections must be seen to by the person installing the equipment. The horizontal l tank is made of zinc-plated steel. ACCESSORIES SORIES PRIMING TANK KIT The available accessories kit includes: - Filling and discharge valves, reductions, non-return valve, closing plugs and automatic air discharger. - Float switch tap complete with ring nut for fixing to the hole through the tank. - Level indicator to connect to the electric panel and assembly instruction sheet. Available on request tank support, height 7, 1, 1, 2 cm. Example of connection to the tank and accessories: N DESCRIPTION N DESCRIPTION 1 Pump priming tank 8 Priming supply non return valve 2 Pipe return from pump delivery side 9 Priming supply on-off valve 3 Floating valve 1 Over flow 4 In flow on-off valve 11 Pressure switch In flow 12 Pump 6 Low level switch 13 To trunk main 7 Drain 14 Pipe connection to delivery side of the pump En-acc-adesc-en_b_tc 148

149 ELECTRIC JOCKEY PUMP KIT The jockey pump or compensation pump has the job of keeping the system under pressure and compensating for any small loses without the intervention of the service pumps. In fact, the jockey pump is commanded by an automatic shut-off panel. Should an electric jockey pump of a different size from the standard be required or should it be installed later on sets which are not predisposed, or should non-standard different size requirements be required, it is possible to configure the booster set with just the service pumps and add the electric jockey pump, also later on. The kit includes: - the hydraulic components for installing the electric pump (base, valves, pressure switch). - the pre-chosen electric pump and the relative electric panel. The hydraulic connection to the set can be easily carried out using one of the couplings on the delivery manifold for the membrane tanks using an adaptor. Kits are available for the vertical electric jockey pumps SV2, SV4, SV8 series and submersed series 2GS, 4GS, 6GS. The diagram illustrates some connection examples: N DESCRIPTION 1 Electric pump 2 Control Box 3 Connection to trunk main 4 Pipe connection to delivery side of the jockey pump To trunk main acc-kit-fil-en_a_tc 149

150 PANEL BRACKET KIT The electric command panels supplied separately, for example in the sets with submersed pumps, are suitable for being mounted on the wall. Universal bracket kit are available, upon request, for supporting the panels; it must be fixed to the floor using blocks. GU_ACC_M1_A_SC HYDRAULIC CONNECTION FOR FIRE-FIGHTING EN 1284 SETS N DESCRIPTION N DESCRIPTION 1 Suction piping kit * Flow meter kit * 2 Delivery manifold 6 Drain 3 Drain 7 Open discharge 4 From priming tank * 8 To trunk main * See the instruction sheets. En-acc-gener-en_a_tc 1

151 ACCESSORIES SORIES NEW RATE OF FLOW INDICATOR < DN1 FLOATS MONITORED VALVES VALVES HYDRO TUBE FLOW METER RATE OF FLOW INDICATOR ELASTIC JOINTS PRESSURE SWITCHS 11