SubDrive75/100/150/300/2W MonoDrive, MonoDriveXT

Transcription

1 SubDrive75/00/50/00/W MonoDrive, MonoDriveXT EMA / EMA / EMA R Quick Installation Guide Status État Estado n English... n Français... n Español...

2 SubDrive75/00/50/00/W MonoDrive, MonoDriveXT EMA / EMA / EMA R Quick Installation Guide Contents Location.... Wire Routing Grounding Grounding/Generator Sizing... 7 Wiring/Configuration EMA... 8 Wiring/Configuration EMA Wiring/Configuration SubDriveW... Plumbing... Accessories....

3 Location Mount drive to a sturdy supporting structure (wall or post). EMA - Indoor nly EMA R/EMA - Indoor/utdoor Mount the drive as close as possible to the service entrance panel. 6" 5 cm Allow a 6" (5 cm) clearance around the drive for cooling. 6" 5 cm 6" 5 cm Use the holes and guides provided. (D T drill holes in the drive.) 6" 5 cm Use a dedicated branch circuit for the drive. Wire directly from the service entrance panel. (5A for SubDrive75/MonoDrive/SubDriveW) (0A for SubDrive00/MonoDriveXT) (0A for SubDrive50) (0A for SubDrive00) Service entrance ground rod It is recommended to wire directly to the service entrance panel. (D T wire to a sub panel located in a home.) I HME Sub

4 Wire Routing D T run input power and motor wires together. Separate input power and motor wiring by at least 8" (0. cm) Separate by at least 8" (0. cm) utput lead to motor to exit house as soon as possible. Input power 8" 0. cm Input power Pump When possible D T run drive input power or motor wires in parallel with house wiring. Avoid running out-building wires in parallel with motor wires.

5 Wire Routing K 8" (0. cm) min. 8" (0. cm) min. 90º Cross over other branch circuits and house wiring at 90º. Satellite/ Antenna wire TV Branch Branch Branch 8" (0. cm) min. 8" (0. cm) min. 8" (0. cm) min. 8" (0. cm) min. Telephone If it is necessary to run wiring in parallel, keep drive input power and motor wires at least 8" (0. cm) from other house wiring. 5

6 Grounding Ensure that a proper utility ground rod is present & connected. L L Ensure that a proper utility ground rod is present & connected. A dedicated output ground wire from the drive must be connected to the motor (motor wires and ground wires must be bundled together). A dedicate from the d to the mot wires mus L L Service entrance ground rod An input power ground wire from the supply panel must be connected to the drive. Service entrance ground rod An Pump input power ground wire from the supply panel must be connected to the drive. Pump Use the service entrance panel ground LY. Avoid multiple ground paths. Use the service entrance panel ground LY. Pump 6 multiple ground paths. D T run ground wire separate

7 Grounding/Generator Sizing Use the service entrance panel ground LY. Pump Pump D T run ground wire separate. ground wire MUST be bundled with motor wires. Generator Sizing for SubDrive/MonoDrive Basic generator sizing for the Franklin Electric SubDrive/MonoDrive system is.5 times maximum input watts consumed by the drive, rounded up to the next normal sized generator. Recommended minimum generator sizes: MonoDrive / hp = 000 Watts ( kw) / hp = 000 Watts ( kw) hp = 500 Watts (.5 kw) MonoDriveXT.5 hp = 000 Watts ( kw) hp = 5000 Watts (5 kw) SubDrive75 = 500 Watts (.5 kw) SubDrive00 = 5700 Watts (6 kw) SubDrive50 = 7000 Watts (7 kw) SubDrive00 = 000 Watts ( kw) SubDriveW = 6000 Watts (6 kw) ote: ot to be used on GFIC circuit or externally regulated generators. Verify voltage, hertz and idle speed are appropriate to supply drive. 7

8 Wiring/Configuration-EMA SubDrive75, SubDrive00, SubDrive50, MonoDrive & MonoDriveXT To operate a different pump size, a Configuration Switch (SW) must be positioned to select the correct pump rating. Reference the chart below for appropriate Configuration Switch setting. From Power Source L L L (Input) Configuration Switch SW Sensor Connection SW See chart below for appropriate controller setting. Reference the SubDrive/MonoDrive Installation Manual or inside of lid for more information. Black Red utput to Feed the motor leads through securely attach to the terminals matching the lead colors. Feed the pressure sensor wires through the small enclosure opening and securely attach to the sensor terminals. Power Supply from Circuit Breaker Red Yel (utput) MonoDrive MonoDriveXT SubDrive75 SubDrive00 SubDrive50 / hp (motor).5 hp (motor)* / hp (pump)* hp (pump)*.5 hp (pump)* Blk Cable Feed the 0 V power leads through the large enclosure opening and securely attach to the terminals marked L, and L. Configuration Switch SW MonoDrive MonoDriveXT SubDrive75 SubDrive00 SubDrive50 / hp (motor)* /A hp (pump).5 hp (pump) hp (pump) MonoDrive MonoDriveXT SubDrive75 SubDrive00 SubDrive50 hp (motor) hp (motor).5 hp (pump) hp (pump) hp (pump) *(default) # Switch Underload sensitivity selection FF Position - ormal(default) Position - Low # Switch Steady Flow - Control selection FF Position - Standard(default) Position - Steady Flow 8

9 E RED RV E T IPUT FILTER RV RV E J RV SESR R ADJUST SW FA SW RV8 RV9 RED E6 J YEL (IPUT) E5 T UTPUT FILTER BLK E Wiring/Configuration-EMA SubDrive75, SubDrive00, SubDrive50, MonoDrive & MonoDriveXT To operate a different pump size, a Configuration Switch (SW) must be positioned to select the correct pump rating. Reference the chart below for appropriate Configuration Switch setting. Sensor Connection SESR Red Blk Configuration Switch SW See chart below for appropriate controller setting. Reference the SubDrive/MonoDrive Installation Manual or access cover for more information. From Power Source J L L (Input) REVB BLACK L L (IPUT) Sensor Connection RED YEL BLK (BR) (BLU) (UTPUT) SESR RV0 SESR Red Blk utput to J Configuration Switch SW See chart below for appropriate controller setting. Reference the SubDrive/MonoDrive Installation Manual or access cover for Red Yel Blkmore information. (Brn) (Blue) (Blk) (utput) From Power Source utput to Power Supply From Circuit Breaker Feed the 0 V power leads through securely attach to the terminals marked L, and L. J L L (Input) Feed the pressure sensor wires through the small enclosure opening and securely attach to the sensor terminals. Feed the 0 V power leads through securely attach to the terminals marked L, and L. L L RED (BR) YEL (BLU) (UTPUT) Feed the motor leads through SESR securely attach to the terminals matching the lead colors to the colors shown. Feed the pressure sensor wires through the small enclosure opening and securely attach to the sensor terminals. BLK J Red Yel Blk (Brn) (Blue) (Blk) (utput) Feed the motor leads through securely attach to the terminals matching the lead colors to the colors shown. Configuration Switch SW MonoDrive MonoDriveXT SubDrive75 SubDrive00 SubDrive50 / hp (motor).5 hp (motor)* / hp (pump)* hp (pump)*.5 hp (pump)* MonoDrive MonoDriveXT SubDrive75 SubDrive00 SubDrive50 / hp (motor)* /A hp (pump).5 hp (pump) hp (pump) MonoDrive MonoDriveXT SubDrive75 SubDrive00 SubDrive50 hp (motor) hp (motor).5 hp (pump) hp (pump) hp (pump) *(default) # Switch Underload sensitivity selection FF Position - ormal(default) Position - Low # Switch Steady Flow - Control selection FF Position - Standard(default) Position - Steady Flow 9

10 SESR SHUT-FF Wiring/Configuration-EMA SubDrive00 To operate a different pump size, a Configuration Switch (SW) must be positioned to select the correct pump rating. Reference the chart below for appropriate Configuration Switch setting. Pressure sensor cable connection Make sure the connection is securely made Configuration Switch SW See chart below for appropriate controller setting. Reference the SubDrive/MonoDrive Installation Manual or inside of lid for more information. SESR SHUT-FF IT FA RELAY PFC FA IV FA CM SW SW Sensor Connection From Power Source utput to SESR SHUT-FF L (Input) L Red Yel Blk (Brn) (Blue) (Blk) (utput) Red Blk Wh Grn Power Supply From Circuit Breaker Feed the motor leads through securely attach to the terminals matching the lead colors to the colors shown. Feed the 0 V power leads through securely attach to the terminals marked L, and L. Feed the pressure sensor wires through the small enclosure opening and securely attach to the sensor terminals. (default) Configuration Switch SW SubDrive00 hp (pump) SubDrive00 5 hp (pump) # Switch Underload sensitivity selection FF Position - ormal(default) Position - Low 0 # Switch Steady Flow - Control selection FF Position - Standard Position - Steady Flow (default)

11 T USED PE CIRCUIT SHRT CIRCUIT VEHEATED CTRLLER Wiring/Configuration-SubDriveW SubDriveW To operate a different pump size, a Configuration Switch (SW) must be positioned to select the correct pump rating. Reference the chart below for appropriate Configuration Switch setting. DISPLAY STATUS Run Mode Configuration Switch SW See chart below for appropriate controller setting. Reference the SubDrive/MonoDrive Installation Manual or inside of lid for more information. From Power Source SW 6 7 # -9 Idle Mode Sleep Mode Reference the ESSURE SubDrive/MonoDrive SESR C Installation Manual or inside of lid for more information. CM L L (Input) L L (IPUT) BLK BLK (UTPUT) Feed the 0 V power leads through the large enclosure opening and securely attach to the terminals marked L, L and. Power Supply From Circuit Breaker Cable to Pressure Sensor SESR C CM Sensor Connection SESR Red Blk utput to BLK BLK (utput) Feed the motor leads through the large enclosure opening and securely attach to the terminals matching the lead colors to the colors shown. Sleep button Depress to engage sleep mode Depress again to resume normal operation See install manual for detailed description Configuration Switch SW SubDriveW / hp (motor) SubDriveW / hp (motor)* SubDriveW hp (motor) *(default) # Switch Underload sensitivity selection FF Position - ormal (default) Position - Low # Switch Reserved - Do not use.

12 Plumbing Minimum Pressure Tank Size (Total Capacity) Pump Flow Rating Controller Model Minimum Tank Size SubDrive75 or MonoDrive gallons (8 L) Less than gpm SubDrive00 gallons (8 L) SubDrive50 or MonoDriveXT gallons (8 L) SubDrive00 8 gallons (5 L) SubDrive75 or MonoDrive gallons (8 L) gpm and higher SubDrive00 8 gallons (5 L) SubDrive50 or MonoDriveXT 8 gallons (5 L) SubDrive00 0 gallons (80 L) All flows SubDriveW 0 gallons (80 L) The pressure tank pre-charge setting should be 70% of system pressure sensor setting. Pressure Setting Guide Pump 6 ft (.8 m) max Pressure WARIG Submersible pumps can develop very high pressure in some situations. Always install a pressure relief valve able to pass full pump flow at 00 PSI. Install the pressure relief valve near the pressure tank. Gauge Pressure Relief Valve Pressure Sensor (Discharge into drain rated for max pump output at relief pressure.) Pressure Shut-off Sensor Turn right (clockwise) to increase pressure setting. Turn left (counter clockwise) to decrease pressure setting. ¼ turn = psi Drain Valve SubDrive00 only 7/ " Allen-wrench (provided) Pressure sensor factory preset for 50 psi Pressure Sensor Set Point (PSI) (Factory set) Pressure Tank Pre-charge (± PSI) on-adjustable Pressure switch factory preset for 00 psi Position the pressure sensor between vertical (preferred) and horizontal. SESR CUT-FF SWITCH SubDrive00 only Position the pressure switch between vertical (preferred) and horizontal. Accessories Pressure Sensor Kit - replacement sensor with 0 ft of AWG cable and sensor adjustment tool: (SubDrive75/00/50, MonoDrive, MonoDriveXT, SubDriveW) Sensor Cable Kit - 00 feet of AWG pressure sensor cable: (SubDrive75/00/50, MonoDrive, MonoDriveXT, SubDriveW) Pressure Sensor Kit - replacement sensor, pressure shut-off switch with 0 ft of AWG cable and sensor adjustment tool: (SubDrive00) Sensor Cable Kit - 00 ft of AWG pressure sensor and pressure shut-off switch cable: (SubDrive00) Fan Replacement Kit - refer to Installation Manual, Franklin Electric hotline or for additional information.