TRAC-Station BT Installation Instructions

Size: px
Start display at page:

Download "TRAC-Station BT Installation Instructions"

Transcription

1 TRAC-Station BT Installation Instructions P/N P1 November UTC Fire & Security. All rights reserved. Introduction This is the Supra TRAC-Station BT Installation Instructions. Read these instructions and the lockset installation instructions before installing TRAC-Station BT. If you do not mount TRAC-Station BT accurately, it will not function properly. Supra is not responsible for replacing the TRAC-Station BT if it is damaged or destroyed upon removal. Installation supplies provided Installation instructions Drill template Electronics enclosure with lid Mounting plate (interior) Exterior TRAC-Station BT plate Eight AA batteries Two sets of four #8 flat head screws (Two different screw lengths for the mounting plate) One electrified lockset (no lock core) Four #8 5/16 in. (8 mm) pan head screws and lock washers (for electronics enclosure) Six #4 1/2 in. (13 mm) flat head screws Plastic weather cover assembly CAUTION: The electronics in this package are electrostatic sensitive devices. Before you install the unit, discharge or use a grounding belt. Installation tools required Drill Drill bits File Phillips screwdriver Level or punch Pen or pencil Hardware not provided When a lockset is provided with the TRAC-Station BT, the lockset will not include a lock core. If you install the TRAC-Station BT into a door that has a noncylindrical lock (for example, a mortise lock), you will need additional hardware. Consult a locksmith for the parts you need for the conversion. Figure 1. Standard TRAC-Station BT installation Installation notes The TRAC-Station BT is designed to be installed above, below, or to the side of the lockset (Figure 1). We recommend 6 in. (15 cm) above the lockset, or as far above the lockset as needed to be out of the way of door hardware. To meet ADA requirements, the lockset must be no higher than 48 in. (120 cm) from the ground to center of the device. If you install the TRAC-Station BT in a wood door, align it horizontally with the lockset and latch (Figure 2). When drilling, drill the latch set hole through the backset hole and into the door. You will use this hole to thread the wiring from the lockset to the TRAC-Station BT. Align the TRAC-Station BT drill template (PN: 43336) so that the 5/8 in. (16 mm) wire feed hole intersects with the horizontal hole. Use this channel to feed the wire from the lockset to the TRAC-Station BT. When you install the lockset, allow room for expansion in hot weather. Figure 2. TRAC-Station BT wood door installation

2 2 Installation To install the TRAC-Station BT: 1. Remove the lid from the electronics enclosure and unplug the four-prong connector. 2. Using the drill template, mark the four mounting holes and the one center wire feed hole on the exterior side of the door. Drill the four mounting holes 9/16 in. (14 mm) and the center wire feed hole 5/8 in. (16 mm) through the door. Note: If you are drilling a metal door, be sure to file the rough edges of the drill holes or use a countersink drill. 3. Remove the existing lockset and install the new lockset using the instructions provided by the manufacturer. Thread the two-wire plug from the lockset through the door and through to the interior using the 5/8 in. (16 mm) wire feed hole. 4. Feed the four-wire plug from the exterior TRAC- Station BT plate through the wire feed hole, and secure the interior mounting plate to the exterior TRAC-Station BT plate (Figure 3). Insert and tighten screws through the interior plate using the recommended screw lengths (Table 1). Note: If the screw does not fully secure the plates to the door when tightened, use a shorter screw. Do not overtighten the long screw. Table 1. Recommended screw length Door thickness Screw length 1.25 to 2.00 in. (32 to 49 mm) 1.00 in. (25 mm) 2.00 to 2.65 in. (50 to 67 mm) 1.75 in. (44 mm) 2.75 to 3.50 in. (68 to 85 mm) 2.50 in. (64 mm) 3.50 to 4.00 in. (85 to 98 mm) 3.00 in. (76 mm) 5. Thread the four-wire plug from the exterior TRAC-Station BT plate, and the two-wire plug from the lockset through the wire feed hole in the electronics enclosure (Figure 4 on page 3). You will attach the wires after securing the enclosure. 6. Use the four #8 5/16 in. (8 mm) pan head screws and lock washers to attach the electronics enclosure to the interior mounting plate. Insert and tighten the screws and lock washers securely. 7. Attach the four-wire plug to the four-wire connector. Snip off the two-wire plug and terminate the two lockset wires on the positive and negative DC output terminals. Polarity is not important when terminating the lockset wires. Figure 3. TRAC-Station BT assembly as example Exterior TRAC-Station BT Plate Lockset 2-wire plug Interior Mounting Plate Electronics Enclosure Electronics Enclosure Lid 4-wire plug

3 Other wiring options The TRAC-Station BT is designed to interface with a variety of electronic devices. For 12-volt applications, all of the DIP switches need to be closed. For 24-volt applications, all of the DIP switches need to be open. The first two terminals on the circuit board are the input power source. Correct polarity is very important for the TRAC-Station BT to function accurately when wiring for a DC application. The next two terminals marked + and DC output are designated for the output power source. Negative power input must be isolated from negative output. Failure to do so will result in damage to the unit. When wiring, do not short the transformer. Wire the transformer with caution since it is not fuse-protected. The last three terminals are the dry contacts you can use to shunt an alarm or as a trigger to activate a relay or other low voltage device. In order to shunt the alarm circuit when entering a door, wire the TRAC-Station BT dry contacts in parallel at the switch on the field side of the alarm zone. This will ensure the resistor is in the circuit. 3 Figure 4. Electronics enclosure OPEN - INPUT PWR + - DC OUTPUT + NC-RED COM NO-GRN

4 4 Testing and completing the installation 1. Once the lock is installed, perform an Install function with a valid TRACcess ekey. Refer to the TRACcess ekey user instructions for step by step operation. 2. Test the lock operation using the TRACcess ekey. Refer to the TRACcess ekey user instructions for step by step operation. Test the lock first with the door open and then with the door shut to ensure the lock strike catches the door frame. When you test the lock with your key, the LED at the top of the interface will flash green, indicating the door may be opened. If the TRAC-Station BT is programmed for TIMED mode, the light will remain flashing for a preprogrammed period of time, during which the door may be opened. If the TRAC-Station BT is programmed for LATCHED mode, once the light flashes green, the door may be opened until the TRAC-Station BT is reset. If the TRAC-Station BT is programmed for LATCHED mode, be sure to reset the lock. 3. Once you have tested the lock, place the lid on the back of the electronics enclosure and position the logo directly over the battery pack. Insert the provided six #4 1/2 in. (13mm) flat head screws into the predrilled holes. Hand-tighten the upper right corner screw and continue hand-tightening the remaining screws in a clockwise order. Do not overtighten the screws, as doing so may damage the electronics enclosure and prevent the lid from being securely fastened. 4. Install the plastic weather cover. 5. Record the serial number and installation location. Figure 5. Wiring diagram for continuous unlock option Continuous unlock option (Optional) There is an option in TRAC-Station BT in latched mode to energize the lockset to unlock for long periods of time. Place an 18 AWG jumper between the DC input + and the common relay of the dry contacts (Figure 5). Connect the lockset between DC input + or input - and the normally open relay. When a DisplayKEY or ekey access the TRAC-Station BT, the lockset will energize and be held until the key is used again to relock the lockset. DC output is not used in this application. Battery removal/disposal This product contains eight AA batteries. To remove the batteries, do the following: 1. Remove the lid from the electronics enclosure. 2. Pull the batteries out of the slots. For proper recycling, dispose of all batteries as required by local ordinances or regulations. FCC The device, Assy, Bezel, WTI, part number G1, complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. 2002/96/EC (WEEE directive). Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. Jumper OPEN - INPUT PWR + - DC OUTPUT + NC-RED COM NO-GRN Supra:

5 5 Introduction TRAC-Lock & TRAC-Station Drill Template P/N B November UTC Fire & Security. All rights reserved. This is the TRAC-Lock & TRAC-Station Drill Template for TRAC-Lock models , , , , and , TRAC-Lock BT models , , , TRAC-Station model and TRAC-Station BT models , , in. (6.73 cm) 1.07 in. (2.72 cm) 3.25 in. (8.26 cm) 5/8 in. diam. (1.59 cm) 5.85 in. (14.86 cm) 9/16 in. diam. (1.43 cm) 4 holes Supra:

6 6 TRAC-Station BT Wiring Diagram Required FCC ferrite bead For remote mounting: Splice the provided pig-tail connector to the 4-wire plenum cable with the provided gel-filled crimp connectors. Splice the matching colors together. For remote mounting: Route 4-wire plenum cable as required. Bezel (or mortise) key interface For remote mounting: Use the provided gel-filled connectors and splice matching colors together. Use provided tie wrap to ensure stress relief for the wires. Optional alarm shunt schematic Alarm Resistor Zone terminal strip Optional entrance feedback DIP switches: 12 V all closed 24 V all open Door sensor Relay contacts for alarm shunt 24 VDC 1.5 amps Pos output Relay: N/C Relay: Common Relay: N/O 24 VDC, 1.5 amp facility power OR UL approved 35 watt output transformer 110 VAC Splice power wires as required with the provided gel-filled crimp connectors Regulated power output 12 or 24 volt maximum 1 amp Electric locking device Neg output Pos power input Neg power input Detail terminal strip

CM5100 COMPUTER MANAGED CYLINDRICAL LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL

CM5100 COMPUTER MANAGED CYLINDRICAL LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL The 5100 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5100 employs a heavy-duty mechanical design which is easy to install and highly reliable. The FSE

More information

CSI-300 Installation Instructions

CSI-300 Installation Instructions CSI-300 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces

More information

* * M400 Series. Features. Models. Trims. UL Requirements. Single Electromagnetic Locks: M420, M450, M490. Installation Instructions

* * M400 Series. Features. Models. Trims. UL Requirements. Single Electromagnetic Locks: M420, M450, M490. Installation Instructions *44487296* M400 Series 44487296 Single Electromagnetic Locks: M420, M450, M490 Installation Instructions M420/M450 Armature plate assembly M490 Armature plate assembly Features Automatic Voltage Selection

More information

(SB2) (SB1) (SB3) (SB5) (SB4) Cylindrical Installation Instructions. A. CHECKLIST (4 each AA Batteries Included) (SB1) (SB4) (SB2) (SB6) (SB6) (SB3)

(SB2) (SB1) (SB3) (SB5) (SB4) Cylindrical Installation Instructions. A. CHECKLIST (4 each AA Batteries Included) (SB1) (SB4) (SB2) (SB6) (SB6) (SB3) A. CHECKLIST (4 each AA Batteries Included) FOR DOOR AND FRAME PREPARATION INSTRUCTIONS, SEE APPENDIX A OR GO TO PROXESS.COM Parts List: Each Proxess C-Series lockset includes Exterior lock assembly (include

More information

Installation Guide(s)

Installation Guide(s) FCC Part 15 Transmitter Certification Test Report FCC ID: SPI-4XXKPMR FCC Rule Part: 15.09 ACS Report Number: 05-070-15C Manufacturer: Single Access Lock Inc. Model: 4XXKP/MR Installation Guide(s) 5015

More information

CSI-100 Installation Instructions

CSI-100 Installation Instructions CSI-100 Installation Instructions Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting

More information

CV41. Vehicle Mounting Kit. Reference Guide

CV41. Vehicle Mounting Kit. Reference Guide CV41 Vehicle Mounting Kit Reference Guide CV41 Vehicle Mounting Kit Reference Guide........... 3 Secure the Smart Dock to a Vehicle.................... 3 Supply Power to the Smart Dock......................

More information

5000 SERIES POWER SUPPLY/CHARGERS INSTALLATION GUIDE

5000 SERIES POWER SUPPLY/CHARGERS INSTALLATION GUIDE 5000 SERIES POWER SUPPLY/CHARGERS INSTALLATION GUIDE MODEL# 505 ( AMP @ VDC OR 4VDC) MODEL# 5500 ( AMP @ VDC OR AMPS @ 4VDC) MODEL# 5600- (0 AMPS @ VDC) MODEL# 5600-4 (5 AMPS @ 4VDC) IMPORTANT SAFETY INSTRUCTIONS

More information

IRRIGATION 810-3T-PLUS TRANSMITTER GUIDE

IRRIGATION 810-3T-PLUS TRANSMITTER GUIDE IRRIGATION 810-3T-PLUS TRANSMITTER GUIDE Pg. 2 HOT SHOT OVERVIEW 3 STANDARD OPERATION MODE 4 HOW TO CONTROL AND SHARE MULTIPLE S 5 TRANSMITTER FUNCTION SWITCH SETTINGS 6 OPERATING THE TEST BEACON 7 OPERATING

More information

Security and Keyless Entry Installation Guide ca 1051

Security and Keyless Entry Installation Guide ca 1051 PROFESSIONAL SERIES Security and Keyless Entry Installation Guide ca 1051 ca1051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection

More information

CA-110 Installation Instructions

CA-110 Installation Instructions CA-110 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

MM1 Installation Instructions

MM1 Installation Instructions MM1 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or

More information

Adjustable Light Kits E-Z-Go TXT All Models Installation Instructions

Adjustable Light Kits E-Z-Go TXT All Models Installation Instructions Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative

More information

ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI

ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI II 1400-6 ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI ACSI 1426-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1092, REV. C INSTALLATION For C-UL Listed applications,

More information

ONE TOUCH CONTROL BOX

ONE TOUCH CONTROL BOX ONE TOUCH CONTROL BOX CONVERSION KIT INSTRUCTIONS REMOVAL, INSTALLATION, OPERATION, AND REMOTE CONTROL PROGRAMMING THUNDERSTONE PART #101322 REVISION A JULY 14 TH 2016 2 P a g e INSTALLING THE THUNDER

More information

Paxton. ins us. Paxlock US

Paxton. ins us. Paxlock US Paxton ins-40213-us Paxlock US ? 3 5 2* 9 10 12 1 4 6 8 11 13 14 7 16 19* 20 21 15 17 18 22 x 2 X 3 x 2 What s in the box 1) Front handle 2) Lock Cylinder * 3) Paxlock front housing 4) Motor adjustment

More information

2904 Power Supply Installation Instructions I-EA00041

2904 Power Supply Installation Instructions I-EA00041 FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and

More information

INSTALLATION INSTRUCTIONS CRL JACKSON 2085E

INSTALLATION INSTRUCTIONS CRL JACKSON 2085E INSTALLATION INSTRUCTIONS CRL JACKSON 2085E ELECTRIC LATCH RETRACTION CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com

More information

Plasma Display Electric Ceiling Lifts

Plasma Display Electric Ceiling Lifts I N S T R U C T I O N M A N U A L The Plasma Display Electric Ceiling Lift is designed for plasma displays requiring an extended drop (18 to 42 inches) from their hidden location. The lift is designed

More information

M400 Series Double Locks. Features

M400 Series Double Locks. Features *44487304* 44487304 M400 Series Double Locks Double Electromagnetic Locks: M422, M452, M492 Installation Instructions Automatic Voltage Selection (AVS) Magnet immediately detects 12VD or 24VD when power

More information

LGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions

LGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative

More information

Elmdene International Ltd

Elmdene International Ltd 1 Elmdene International Ltd Tel: +44(0)23 9269 6638 3 Keel Close, Interchange Park, Fax: +44(0)23 9266 0483 Portsmouth, Hampshire, PO3 5QD, UK Web: www.elmdene.co.uk 13.8Vdc Switch Mode Power Supply GEN3-08-y

More information

Series BFM Bulk Flow Monitor 1A FUSE RED LED RELAY. Part Number BFM-1 BFM-2 BFM-3 BFS-1

Series BFM Bulk Flow Monitor 1A FUSE RED LED RELAY. Part Number BFM-1 BFM-2 BFM-3 BFS-1 Series Bulk Flow Monitor Specifications - Installation and Operating Instructions Bulletin FL-1-4x 3/4 CONDUIT KNOCKOUTS BFS 1A FUSE RED LED RELAY 5-9/64 [130.45] TRANSFORMER 3[76.20] GREEN LED 7 [177.80]

More information

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED 100755-2 Installation Instructions PC 4200 PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Mortise Lockset Installation Instructions ML20600 TCRNE1 Series M812 - iclass Reader Option

Mortise Lockset Installation Instructions ML20600 TCRNE1 Series M812 - iclass Reader Option Mortise Lockset Installation Instructions ML20600 TCRNE1 Series M812 - iclass Reader Option Attention Installer FM312 6/09 (617419050) Please read these instructions carefully to prevent missing important

More information

Instruction Manual for the. E-SL 450 Series

Instruction Manual for the. E-SL 450 Series Instruction Manual for the E-SL 450 Series Estate Slide Summary of Functions The Estate Slide is only to be used for vehicular Slide gates in a Class I setting. Class I: A vehicular gate opener (or system)

More information

Cylindrical Lockset Installation Instructions CL33600 TCRNE1 Series M812 - iclass Reader Option

Cylindrical Lockset Installation Instructions CL33600 TCRNE1 Series M812 - iclass Reader Option Cylindrical Lockset Installation Instructions CL33600 TCRNE1 Series M812 - iclass Reader Option Attention Installer FM313 6/09 (617417060) Please read these instructions carefully to prevent missing important

More information

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;

More information

ACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS

ACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS II 1400-8 Features: ACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS Filtered/Regulated 24 Volts DC Up to Full 2 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit

More information

AccuPower AQU128B Installation Instructions

AccuPower AQU128B Installation Instructions Tel 1.800.MAGLOCK info@securitron.com 1.800.624.5625 www.securitron.com AccuPower AQU128B Installation Instructions Recommended Tools & Additional Materials #2 Phillips Screw Driver Wire connectors Lead

More information

FM200 FLOW/NO-FLOW MONITOR INSTALLATION AND TECHNICAL MANUAL 120 VAC MODEL 6/1/2017

FM200 FLOW/NO-FLOW MONITOR INSTALLATION AND TECHNICAL MANUAL 120 VAC MODEL 6/1/2017 FM200 FLOW/NO-FLOW MONITOR INSTALLATION AND TECHNICAL MANUAL 120 VAC MODEL 6/1/2017 Maxi-Tronic, Inc. 417 Wards Corner Road Loveland, OH 45140 513.398.2500 800.659.8250 FAX: 513.398.2536 info@maxitronic.com

More information

Installation Instructions RF4510-EA

Installation Instructions RF4510-EA Installation Instructions RF4510-EA HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 1 Product Description Dimensions Orientation Compatibility Access Control Systems Proximity Cards Frequency

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Installation Instructions

Installation Instructions AQU244 & AQU128 Series Installation Instructions Installation Instructions AQU244 24vdc 5A Supervised Power Supply/Charger module AQU128 12vdc 10A Supervised Power Supply/Charger module Both Mounted in

More information

TC26-B Vehicle Sensor

TC26-B Vehicle Sensor Section 1 General Description The Model TC26-B is a microprocessor controlled vehicle sensor with a variable range. It is designed to trigger the operation of a traffic controller. The TC26-B will only

More information

ASSEMBLING THE 15 INCH FLUSH MOUNT TOUCH SCREEN DIMENSIONS OF THE 15 INCH FLUSH MOUNT TOUCH SCREEN

ASSEMBLING THE 15 INCH FLUSH MOUNT TOUCH SCREEN DIMENSIONS OF THE 15 INCH FLUSH MOUNT TOUCH SCREEN DIMENSIONS OF THE 15 INCH FLUSH MOUNT TOUCH SCREEN 18 (457 mm) 12 39/64 (320 mm) 3 1/2 (89 mm) 1 13/32 (36 mm) 19 (483 mm) 3 5/8 (92 mm) 7/64 3 mm) 1 13/32 (36 mm) 23 53/64 (605 mm) 20 3/4 (527 mm) 12

More information

WirelessONE. Kit INSTALLATION GUIDE. Key Fob Activated Compressor System

WirelessONE. Kit INSTALLATION GUIDE. Key Fob Activated Compressor System Kit 25870 Key Fob Activated Compressor System MN-751 (041202) ECR 7260 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before proceeding with installation.

More information

TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL SADDLE BOX STARTER KIT. Model: QDSKSA01. Part No.

TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL SADDLE BOX STARTER KIT. Model: QDSKSA01. Part No. TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL SADDLE BOX STARTER KIT Model: QDSKSA01 Part No. 24-0326 Rev. A ECN 5430 ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS

More information

ELECTRICAL INSTALLATION PROCEDURES For Custom Grid Assemblies & Power Generators

ELECTRICAL INSTALLATION PROCEDURES For Custom Grid Assemblies & Power Generators ELECTRICAL INSTALLATION PROCEDURES For Custom Grid Assemblies & Power Generators BECAUSE CLEAN AIR MATTERS Note: Factory trained or suitably qualified personnel must perform this installation. General:

More information

Covers All 430, 440, 441 and CJ Series Advanced Security Systems.

Covers All 430, 440, 441 and CJ Series Advanced Security Systems. INSTALL GUIDE Covers All 430, 440, 441 and CJ Series Advanced Security Systems www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com FCC/ID Notice This device complies with

More information

MAPNET II Transceiver Installation Instructions

MAPNET II Transceiver Installation Instructions MAPNET II Transceiver Installation Instructions Introduction This publication describes the installation procedure for the following versions of the MAPNET II Transceiver card. 4120/4100-0110 MAPNET II

More information

Installation Instructions

Installation Instructions F20/F25 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Instructions CPL Master Module PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

2 Way Security and Keyless Entry Installation Guide ca 1553

2 Way Security and Keyless Entry Installation Guide ca 1553 PROFESSIONAL SERIES 2 Way Security and Keyless Entry Installation Guide ca 1553 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...

More information

Dodge Engineering & Controls, Inc. Toll Free (877) Fax: (978) EN44 and EN88 Non-Spring Return Electronic Actuators

Dodge Engineering & Controls, Inc. Toll Free (877) Fax: (978) EN44 and EN88 Non-Spring Return Electronic Actuators Dodge Engineering & Controls, Inc. EA678R3 45 a b e d c a. Actuator b. Position indicator c. Mounting bracket (for dampers) d. Mounting screws e. 4 mm hex wrench Figure 1. Parts of the EN44 and EN88 Actuators.

More information

CA-210 Installation Instructions

CA-210 Installation Instructions CA-210 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

Installation. Part A, Section 3. This section covers the following unit configurations. 3400V 3500V. Voltage 4. Pump Piston (E, F, or G)

Installation. Part A, Section 3. This section covers the following unit configurations. 3400V 3500V. Voltage 4. Pump Piston (E, F, or G) Part A, Section 3 Model This section covers the following unit configurations. Voltage 4 3100V 3400V 3500V Pump Piston (E, F, or G) Manifold Control 4-Port (A) 6-Port (B) Vista Temperature (TC) A 3-0 A

More information

TruVision HD-TVI Series 4 PTZ Dome Camera Installation Guide

TruVision HD-TVI Series 4 PTZ Dome Camera Installation Guide TruVision HD-TVI Series 4 PTZ Dome Camera Installation Guide P/N 1073206-EN REV B ISS 03FEB17 Copyright Trademarks and patents Manufacturer Certification 2017 United Technologies Corporation, Interlogix

More information

AccuPower AQU126B Installation Instructions

AccuPower AQU126B Installation Instructions Tel 1.800.MAGLOCK info@securitron.com 1.800.624.5625 www.securitron.com AccuPower AQU126B Installation Instructions Recommended Tools & Additional Materials #2 Phillips Screw Driver Wire connectors Lead

More information

Installation. Part A, Section 3. This section covers the following unit configurations: 3400V 3500V Voltage 1, 2, 3 Pump Piston (E, F, G)

Installation. Part A, Section 3. This section covers the following unit configurations: 3400V 3500V Voltage 1, 2, 3 Pump Piston (E, F, G) Part A, Section 3 Model This section covers the following unit configurations: 3100V 3400V 3500V Voltage 1, 2, 3 Pump Piston (E, F, G) Manifold Control 4-Port (A) 6-Port (B) Vista Temperature (TC) A 3-0

More information

Installation Instructions

Installation Instructions patent pending Portable Proportional Braking System Installation Instructions Part number 9400 Towing and Suspension Solutions ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 800-669-9690 Fax 360-735-9300

More information

ME AGS Auto Gen Start System for Coach Generators. Operator s Manual.

ME AGS Auto Gen Start System for Coach Generators. Operator s Manual. ME AGS Auto Gen Start System for Coach Generators Operator s Manual ME AGS Operator s Manual Auto Gen Start System for Coach Generators Section 2003 - Magnum Energy, Inc. Table of Contents Page 1. Overview

More information

MODELS DSH/KSH/DSV/KSV R-410A LOW-AMBIENT KIT

MODELS DSH/KSH/DSV/KSV R-410A LOW-AMBIENT KIT MODELS DSH/KSH/DSV/KSV R-410A LOW-AMBIENT KIT Supersedes Form145.10-IOM1 (810) Form 145.10-IOM1 (910) LOW-AMBIENT KIT MODELS DSH/KSH/DSV/KSV R-410A AIR CONDITIONING UNITS INSTALLATION INSTRUCTIONS IMPORTANT!

More information

* * M400 Series Double Locks. Double Electromagnetic Locks: M422, M452, M492. Installation Instructions. Mounting Bracket (2)

* * M400 Series Double Locks. Double Electromagnetic Locks: M422, M452, M492. Installation Instructions. Mounting Bracket (2) *44487304* 44487304 M400 Series Double Locks Double Electromagnetic Locks: M422, M452, M492 Installation Instructions Mounting Bracket (2) Inside Mounting Bracket Screws** (4) Mounting Bracket Screws**

More information

Reproduction or other use of this Manual, without the express written consent of Vulcan, is prohibited.

Reproduction or other use of this Manual, without the express written consent of Vulcan, is prohibited. SERVICE MANUAL ELECTRIC BRAISING PANS (30 & 40 GALLON) VE30 VE40 ML-126849 ML-126850 VE40 SHOWN - NOTICE - This Manual is prepared for the use of trained Vulcan Service Technicians and should not be used

More information

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS II 1400-10 ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS Features: Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit Protection Standby Battery

More information

56- Electric Latch Retraction Exit Devices Installation and Wiring Instructions

56- Electric Latch Retraction Exit Devices Installation and Wiring Instructions SECTION I: OVERVIEW 1. Description The Sargent 56- prefix ELR works with 80 Series exit devices to provide remote-controlled latch retraction. It is compatible with the following prefixes: 53 - Latchbolt

More information

Dycon D2430 EN54-4 Fire Alarm Power Supply Series

Dycon D2430 EN54-4 Fire Alarm Power Supply Series Dycon D2430 EN54-4 Fire Alarm Power Supply Series Technical Description Installation and Operating Manual Construction Product Regulation 0359-CPR-00434 Page 1 of 14 Contents 1. General... 3 1.1 Product

More information

AWZ 110. AWZ 13,8V/1A/7Ah/LM

AWZ 110. AWZ 13,8V/1A/7Ah/LM AWZ 110 v.1.3 AWZ 13,8V/1A/7Ah/LM Linear buffer power supply unit Grade 2. EN* Edition: 9 from 02.11.2017 Supercedes the edition: 8 from 23.01.2017 GREY POWER plus Features: EN50131-6 compliance, 1 2 grades

More information

Plasma Display Electric Pop-Up Lift (PUL)

Plasma Display Electric Pop-Up Lift (PUL) I N S T R U C T I O N M A N U A L Plasma Display Electric Pop-Up Lift (PUL) Your is designed for installation in furniture or cabinets. Display mounting is made easy using the Q-latch mounting system and

More information

SHEAR ALIGNING MAGNALOCK MODEL SAM2-24 INSTALLATION AND OPERATING INSTRUCTIONS

SHEAR ALIGNING MAGNALOCK MODEL SAM2-24 INSTALLATION AND OPERATING INSTRUCTIONS Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.6.5625 techsupport@securitron.com in door opening solutions SHEAR ALIGNING MAGNALOCK MODEL SAM2- INSTALLATION AND OPERATING

More information

CAUTION. Even Brakes with a black cable need second vehicle kit Even Brakes with a blue cable need second vehicle kit 98450

CAUTION. Even Brakes with a black cable need second vehicle kit Even Brakes with a blue cable need second vehicle kit 98450 cable not included cable not included Even Brakes with a blue cable need second vehicle kit 98450 Even Brakes with a black cable need second vehicle kit 98400 Check the Even Brake serial number before

More information

ASSA ABLOY. Installation Instructions. MP9800 Series Multi-Point Lock with MELR Option (Electric Latch Retraction)

ASSA ABLOY. Installation Instructions. MP9800 Series Multi-Point Lock with MELR Option (Electric Latch Retraction) Installation Instructions MP9800 Series Multi-Point Lock MP9800 Series Multi-Point Lock, the global leader in door opening solutions 1 of 20 Copyright 2016 Corbin Russwin Inc., an Group company. Table

More information

Outdoor Enclosure Power System ENC X100MP48F20-AC6

Outdoor Enclosure Power System ENC X100MP48F20-AC6 Outdoor Enclosure Power System ENC673034-1X100MP48F20-AC6 Manual MA015151A4 Issue 1 Nov 2010 Copyright 2010 Myers Power Products, Inc. Part# A015151A4 MA015151A4 Iss1 Page 1 of 24 Dimensions Outdoor Enclosure

More information

Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON

Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON LLI-N2.9W Prior to installation, please confirm that you have the required system components listed below. LED Neon Flow Extrusions/Lens (Optional)

More information

MODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.

MODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT. 502-2 & 503-2 Instructions instructions marinco.com Installing and Using the Precision Spotlight MODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.

More information

A-200 Speed Dome. Quick Start Guide UD.6L0201D0127A02

A-200 Speed Dome. Quick Start Guide UD.6L0201D0127A02 A-200 Speed Dome Quick Start Guide UD.6L0201D0127A02 Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the company you purchased the unit

More information

RK Standby Battery Operator s Manual

RK Standby Battery Operator s Manual 49-8104RK Standby Battery Operator s Manual Part Number: 71-0118RK Revision: C Released: 8/4/17 www.rkiinstruments.com Product Warranty RKI Instruments, Inc. warrants gas alarm equipment sold by us to

More information

SPACESAVER EC-300 A ELECTRICS

SPACESAVER EC-300 A ELECTRICS INSTALLATION INSTRUCTIONS SPACESAVER EC-300 A ELECTRICS SECTION I TOP MOUNTED ELECTRICS SECTION II FACE PANEL MOUNTED ELECTRICS SECTION III ZFS INSTALLATION INSTRUCTIONS This symbol indicates a connection

More information

TS93 EMF T/PT/TDE. Surface applied door closer

TS93 EMF T/PT/TDE. Surface applied door closer TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress

More information

CSI-400 Installation Instructions

CSI-400 Installation Instructions CSI-400 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces

More information

Model APS-510C Installation Manual Remote Control Vehicle Security System

Model APS-510C Installation Manual Remote Control Vehicle Security System Model APS-510C Installation Manual Remote Control Vehicle Security System Table Of Contents: Before You Begin Page 2 Wire Harnesses Quick View Page 3 Mounting Of The Major Components Page 4 8 Pin Power

More information

Installation Instructions For Profile Series v.g1.5 Cylindrical Lock

Installation Instructions For Profile Series v.g1.5 Cylindrical Lock Installation Instructions For Profile Series v.g1.5 Cylindrical Lock A7854B Copyright 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in

More information

PSBSH 2012B. PSBSH 13,8V/2A/7Ah/HERMETIC

PSBSH 2012B. PSBSH 13,8V/2A/7Ah/HERMETIC PSBSH 2012B v.1.2 PSBSH 13,8V/2A/7Ah/HERMETIC Buffer switch mode power supply unit, EN** Edition: 7 from 02.11.2017 Supercedes the edition: 6 from 08.06.2017 Features: DC 13,8V/2A uninterruptible power

More information

HANDLING MECHANICAL INSTALLATION

HANDLING MECHANICAL INSTALLATION 2 INSTALLATION DESCRIPTION The and 2 Delay Egress Systems are 1500 pound holding force (holding force not evaluated by UL) per leaf electromagnetic locks, electronically controlled to provide a 15 or 30

More information

ADA EZ Rev. H, 8/23/11

ADA EZ Rev. H, 8/23/11 Installation and Operating Instructions ADA EZ Installation and Operating Instructions EZ040 Note Changes or modifications not expressly approved by the party responsible for compliance could void the

More information

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks Securitron Magnalock Corp. Tel 775.355.5625 550 Vista Boulevard Fax 775.355.5633 Sparks, NV 89434 info@securitron.com www.securitron.com ASSA ABLOY, the global leader in door opening solutions INSTALLATION

More information

Installation and Operation Guide. Tundra HD 2500 Power Inverter. for the. Webasto BlueCool Truck System

Installation and Operation Guide. Tundra HD 2500 Power Inverter. for the. Webasto BlueCool Truck System Installation and Operation Guide Tundra HD 2500 Power Inverter for the Webasto BlueCool Truck System www.tundrainternational.com www.techwebasto.com BCTSP0063A Table of Contents 1. Introduction 4 1.1 Disclaimer.................................................................................

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

WIRELESS TRI-JACK WIRELESS REMOTE KIT COMPONENTS LITERATURE NUMBER REV. C WARNING EXPLOSION WARNING PERSONAL INJURY & PROPERTY DAMAGE

WIRELESS TRI-JACK WIRELESS REMOTE KIT COMPONENTS LITERATURE NUMBER REV. C WARNING EXPLOSION WARNING PERSONAL INJURY & PROPERTY DAMAGE LITERATURE NUMBER 8260. REV. C WIRELESS TRI-JACK Effective July 207 Installation Operation Maintenance SAFETY ALERT SYMBOLS Safety Symbols alerting you to potential personal safety hazards. Obey all safety

More information

Installation Instructions

Installation Instructions Installation Instructions AQU243-8C1R -8F8R -8C8R 24VDC/3.3Amp Supervised (AC & Battery) Power Supply/Charger Module, 85-264vac, 14 x 9 x 3.5" Enclosure, UL294, UL603 & UL1481 Listed AQU243 with one PDB-8C1R

More information

Digital/Analog Amplifiers Installation Instructions

Digital/Analog Amplifiers Installation Instructions Digital/Analog Amplifiers Installation Instructions Introduction This publication describes the installation procedure for the 4100U and 4100ES Fire Alarm Control Panels (FACP) family of digital and analog

More information

Removable Applied Panel Mounting System

Removable Applied Panel Mounting System Removable Applied Panel Mounting System Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences,

More information

M9206-Bxx-2S Series On/Off Electric Spring Return Actuators

M9206-Bxx-2S Series On/Off Electric Spring Return Actuators Installation Instructions M9206-Bxx-2S Issue Date May 14, 2003 M9206-Bxx-2S Series On/Off Electric Spring Return Actuators Installation IMPORTANT: Use this M9206-Bxx-2S Series actuator to control equipment

More information

AWZ 200. AWZ 13,8V/2A/7Ah/L

AWZ 200. AWZ 13,8V/2A/7Ah/L GREY POWER AWZ 200 v.2.4 AWZ 13,8V/2A/7Ah/L Linear, Buffer Power Supply Unit EN** Edition: 7 from 15.05.2014 Supercedes the edition: 6 from 13.02.2014 Features: 13,8VDC/2A uninterruptible supply fitting

More information

L5000 Plus. Installation & Setup Guide

L5000 Plus. Installation & Setup Guide L5000 Plus Page 1 of 16 JDE1945 IssB s1 May 2009 Contents Description Page Safety... 3 Installation Standards 4 Specification. 4 Installation Procedure Pump Box. 6 Auxiliary Pump Boxes... 7 Connecting

More information

RK Standby Battery Operator s Manual

RK Standby Battery Operator s Manual 49-8103RK Standby Battery Operator s Manual Part Number: 71-0117RK Revision: 0 Released: 8/18/08 www.rkiinstruments.com Product Warranty RKI Instruments, Inc., warrants gas alarm equipment sold by us to

More information

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Dycon D1532SM EN50131/PD6662 Grade 3, 12V 2A Power Supply Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Tel: +44 (0)1443 471 900 Unit A Cwm Cynon Business Park Mountain

More information

Installation Instructions

Installation Instructions Portable Proportional Braking System Installation Instructions Part number 9400 Time Tested Time Proven ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 800-669-9690 Fax 360-735-9300 roadmasterinc.com

More information

Installation. Part A, Section 3. This section covers the following unit configurations. 3400V 3500V. Voltage 4. Pump Piston (E, F, G)

Installation. Part A, Section 3. This section covers the following unit configurations. 3400V 3500V. Voltage 4. Pump Piston (E, F, G) Part A, Section 3 Model This section covers the following unit configurations. Voltage 4 300V 3400V 3500V Pump Piston (E, F, G) Manifold Control 4-Port (A) 6-Port (B or C) -Port (S or T) Vista Pattern

More information

Outdoor Enclosure Power System ENC X100MP48F20

Outdoor Enclosure Power System ENC X100MP48F20 Outdoor Enclosure Power System ENC673034-1X100MP48F20 Manual MA015152A1 Issue 1 Oct 2010 Copyright 2010 Myers Power Products, Inc. Part# A015152A1 MA015152A1 Iss1 Page 1 of 22 Dimensions Outdoor Enclosure

More information

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY 00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement

More information

Manual - Inside Front Cover (Blank)

Manual - Inside Front Cover (Blank) FRONT COVER Manual - Inside Front Cover (Blank) Table of Contents Important Information... 2 Recommended Installation Tools... 2 Recommended Procecures... 2 Wiring Diagram... 3 14 Pin Connector...4 Installation

More information

Model APS-101N Installation Manual

Model APS-101N Installation Manual Programmable Features Model APS-101N Installation Manual Select By Operating Transmitter Press Lock Button Press Unlock Button Siren Indications 1 Chirp 2 Chirps Factory Default 1) Arming Method Passive

More information

3143 Production Drive Fairfeild, Ohio Model HA-45. Installation and Service Manual

3143 Production Drive Fairfeild, Ohio Model HA-45. Installation and Service Manual 3143 Production DriveFairfeild, Ohio 45014513-874-3733 Model HA-45 Installation and Service Manual 3143 Production DriveFairfeild, Ohio 45014513-874-3733 Model HA-45 Installation and Service Manual Table

More information

Electrical Options Booklet. Table of Contents

Electrical Options Booklet. Table of Contents *24228413* 24228413 Electrical Options Booklet Table of Contents EL Wiring... EL Troubleshooting... SD/EL 98/99 Cylinder Dogging... SS Wiring... 330, 350, RX-330 and RX-350 Push Bar Trim Mechanical Installation...

More information

650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present

650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior

More information

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY 0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod

More information

INSTALLATION INSTRUCTIONS AM rev. A

INSTALLATION INSTRUCTIONS AM rev. A INSTALLATION INSTRUCTIONS AM16629-1 rev. A READ THIS MANUAL CAREFULLY! FAILURE TO INSTALL THIS EQUIPMENT PER THESE INSTRUCTIONS WILL VOID THE WARRANTY. INTRODUCTION NOTE: Zebra technologies Corporation

More information

Installation Manual. for Off Line Systems. INTELLIKEY is a trademark of INTELLIKEY Corporation GID 04/25/2003. Page 1

Installation Manual. for Off Line Systems. INTELLIKEY is a trademark of INTELLIKEY Corporation GID 04/25/2003. Page 1 Installation Manual for Off Line Systems INTELLIKEY is a trademark of INTELLIKEY Corporation 100419-GID 04/25/2003 Page 1 Page 2 Attention Installer If installation instructions are not followed this may

More information