Service Quantity Lev. 4 A For ECU Mounting 2 A FOR P-CLAMP
|
|
- Erica Shepherd
- 5 years ago
- Views:
Transcription
1 Item Assy. Service Part No. Description Quantity Lev. Parts Remarks - - KEA KIT, WIRE HARNESS (07-CR-TIE4) 1 A - -- KEA INS WIRE HARNESS KIT INSTRUCTIONS 1 A 1 -- KEA WIRE HARNESS, 07-CR-TIE KEA BRACKET, ECU MOUNTING 1 A M x 25MM HEX FLANGE BOLT 4 A For ECU Mounting 4 -- KEA BRACKET, UPPER STRESS RELIEF 07-CRS 1 A Upper Bracket M x 16MM HEX FLANGE BOLT 3 A 6 -- KEA P-CLAMP 2 A M x16MM HEX FLANGE BOLT 2 A FOR P-CLAMP 8 -- KEA BAND, HARNESS 7 A A: Available as Service Parts APPLICABLE ENGINE MODELS: V2607-CR-TIE4 V3307-CR-TIE PAGE 1 OF 6
2 Installation Condition Notes Important Note: The following installation guideline must be followed during installation of the 07 Series-CRS Engine Control Unit (ECU). 1. The 07 Series-CRS ECU must be mounted on the equipment chassis. Engine mounted ECU's are not approved for warranty. 2. The ECU temperature should never exceed 105 C in any operating condition. 3. The ECU should never exceed vibration levels of 5G,.7 mm in any condition. 4. The wire harness should have appropriate stress relief for each connection. Preferred Position OR Optional Positions: 1) Up to 90 Rotation Clockwise 2) Up to 90 Rotation Counter Clockwise Each check point must be checked and evaluated during the application review process. Application approval and warrantee cannot be granted unless each installation condition meets/exceeds the requirements listed above. A completed installation is shown below as an example. EXAMPLE ECU INSTALLATION PAGE 2 OF 6
3 Installation Procedure 1. Mount the ECU bracket (Item# 2) and the ECU with the four mounting bolts (Item# 3) in a location that meets the installation conditions described in the above section. Torque the bolts to Nm (18-20 ft.-lbs.). Note: The vent on the backside of the ECU must be protected from water and or/pressure washing. ECU 2 ECU VENT 3 2. Mount Bracket A (Item# 4) with the three mounting bolts (Item# 5) to the intermediate connector bracket on the engine. Torque the bolts to Nm (18-20 ft.-lbs.). 4 5 PAGE 3 OF 6
4 Installation Procedure Continued 3. Plug in each corresponding wire harness connector into the appropriate locations as described below. Note 1: Never force a connection to the mating connector as this will result in bent terminal pins. Note 2: ECU connectors CN1 and CN2 are keyed differently. Take care to match the connector to the correct ECU connection. Note 3: The MAF (mass air flow) sensor wire is 1200 mm in length to accommodate many installation solutions. Take care to secure any excess wire in the event that the MAF sensor is located in close proximity. Note 4: The interface connector and the main power connector require additional wiring by the OEM. Please refer to the VIC (vehicle interface connector) wire schematic on the final pages of this installation instruction guide for detail. INJECTOR INTERMEDIATE CONNECTOR MAF (MASS AIR FLOW SENSOR CONNECTOR ENGINE INTERMEDIATE CONNECTOR ECU1 CONNECTOR ECU2 CONNECTOR VEHICLE INTERFACE CONNECTOR MAIN POWER CONNECTOR 4. Secure the wire harness with the cable ties provided in the harness kit according to the image below. Install the P-clamps in a reasonable location. At least one additional stress relief on the harness is needed (depends on final ECU location). Note: Add any additional wire harness support as needed (not included in kit). CABLE TIES x 2 P CLAMPS x 2 CABLE TIES x 4 PAGE 4 OF 6
5 Installation Procedure Continued 5. Connect the interface connector and the main power connector. Please refer to the VIC (vehicle interface connector) wire schematics on the final pages of this installation instruction guide for detail. The connector pin outs are shown below (looking into the intermediate wire harness connector). Vehicle Interface Wiring Notes: A. Suppression diodes on the coil side of the relay are required on the main, starter, and Murphy PV480 relay (if used). The installed relays should meet or exceed the specification as shown below: B. Be sure battery cables are connected correctly. Disconnecting either the positive or negative battery cable while the equipment is operating may cause premature failure of electronic components. Also, never weld on equipment with the ECU connected to the wire harness. C. After connecting all terminals to appropriate locations, check the following: a) Make sure the wires do not contact the exhaust manifold or muffler and are away from all heat sources. b) Make sure the wires do not contact any sharp or abrasive surfaces. c) Use wire ties to secure the wire harness to the engine, but never secure the wires to any fuel injection lines. d) Make sure that the all non sealed relays are mounted vertically so that water can drain from the bottom of the connectors. e) Ensure that the wire harness is routed in a way that prevents water from running directly into the ECU or intermediate harness connections. PAGE 5 OF 6
6 F MAIN RELAY + - FUEL FEED PUMP KEA 07-CR-TIE4 INTERMEDIATE WIRE HARNESS: MAIN POWER CONNECTOR MOLEX_ FEMALE CONN MOLEX_ FEMALE TERM (SN) F 20 AMP FUSE 002 WHITE(W)/BLACK(B) 12 AWG 084 BLACK(B)/RED(R) 12 AWG 1: MAIN RELAY CONTACT (12V+) 2: GND E E 50 AMP FUSE B+ IG DIRECT TO BATT (-) D ST 5 AMP FUSE ALTERNATOR IG KEA 07-CR-TIE4 INTERMEDIATE WIRE HARNESS: VIC1 CONNECTOR MOLEX_ FEMALE CONN MOLEX_ TERM (SN) MOLEX_ PLUG D V BATTERY CHARGE CAN FOR VEHICLE 120 ohm 055 BLACK(B)/YELLOW(Y) 18 AWG TWISTED PAIR 029 WHITE(W) 20 AWG 1: MAIN RELAY COIL (-) 9: NOT USED 2: CAN2 - L 10: NOT USED 030 GREEN(G)/RED(R) 20 AWG 3: CAN2 - H 11: NOT USED C CHASSIS GND ENGINE GND 5 AMP FUSE 130 RED(R)/BLACK(B) 18 AWG 4: START SW INPUT 12: NOT USED C 5 AMP FUSE 022 WHITE(W)/RED(R) 18 AWG 5: IGNITION SW INPUT 13: NOT USED STARTER RELAY 031 GREEN(G)/WHITE(W) 20 AWG 6: HEATER RELAY COIL (+) 14: NOT USED B + STARTER SOLENOID BLUE(L)/BLACK(B) 18 AWG 7: STARTER RELAY COIL (-) 15: NOT USED 8: NOT USED 16: NOT USED B + STARTER MOTOR A 100 AMP FUSE HEATER RELAY HEATER DRAWN CHECKED ENG APPR. MFG APPR. Q.A. COMMENTS: NAME KB DATE KUBOTA ENGINE AMERICA TITLE: VEHICLE INTERFACE WIRING 07-CR-TIE4 INTERMEDIATE HARNESS (GENRAL WIRING) SIZE USED IN CONJUNCTION WITH: REV C KEA SCALE: 1:1 SHEET 1 OF 1 A
Service Lev. Parts - - KEA KIT, WIRE HARNESS 03-CR-TIE4, INTAKE SIDE STARTER 1 A 1 A
Item Assy. Service Part No. Description Quantity Lev. Parts Remarks - - KEA08-65100 KIT, WIRE HARNESS 03-CR-TIE4, INTAKE SIDE STARTER 1 A 1 -- KEA08-65100-INS WIRE HARNESS KIT INSTRUCTIONS 1 A 2 -- KEA08-65150
More informationService Quantity Lev. 2 A FOR P-CLAMP
Item Assy. Service Part No. Description Quantity Lev. Parts Remarks - - KEA06-65000 KIT, WIRE HARNESS (07-CRS) 1 A - -- KEA06-65004-INS WIRE HARNESS KIT INSTRUCTIONS 1 A 1 -- KEA06-65050 WIRE HARNESS,
More informationService Lev. Parts - - KEA KIT, WIRE HARNESS 03-CRS, EXHAUST SIDE STARTER 1 A 1 -- KEA INS WIRE HARNESS KIT INSTRUCTIONS
Item Assy. Service Part No. Description Quantity Lev. Parts Remarks - - KEA07-65000 KIT, WIRE HARNESS 03-CRS, EXHAUST SIDE STARTER 1 A 1 -- KEA07-65004-INS WIRE HARNESS KIT INSTRUCTIONS 1 A 2 -- KEA07-65050
More informationInstallation Instructions Rotation Control Kit
Installation Instructions Rotation Control Kit 45-101, REV. 11/14 1 TABLE OF CONTENTS SECTION 1 PURPOSE... 3 SECTION 2 INSTALLATION... 4 Test Installation...6 Disabling The System...6 Operation...6 2 45-101,
More informationInstallation Manual for the Pantera Ignition Switch Bypass
Installation Manual for the Pantera Ignition Switch Bypass This Ignition Switch Bypass solves the Pantera owners problem of replacing the ignition switch that is expensive and difficult to source. The
More informationINSTRUCTION, GPT LOW VOLTAGE THERMAL SWITCH (LVTS) INSTALLATION KIT P/N
LIFT CORPORATION Sht. 1 of 9 DSG# M-07-18 Rev. ~ Date: 08/15/08 INSTRUCTION, GPT LOW VOLTAGE THERMAL SWITCH (LVTS) INSTALLATION KIT P/N 282473-01 LOW VOLTAGE THERMAL SWITCH (LVTS) P/N 905291 INSTRUCTION
More informationInstallation Instructions Clamp Opening Control - Switch Operated
Installation Instructions Clamp Opening Control - Switch Operated 45-078, REV. 8/14 1 TABLE OF CONTENTS SECTION 1 PURPOSE... 3 SECTION 2 INSTALLATION... 4 Test Installation...6 Disabling The System...6
More informationSupplement to Yanmar Kit Installation Instructions SAFETY
Supplement to Yanmar Kit Installation Instructions SAFETY This product is designed and intended only for use with a YANMAR engine. All safety and warning information contained in the Yanmar Operation Manual
More informationElectrical Systems - Machine Electrical System. Electrical System Components Diagram Electrical System Components
Section 5.1 Electrical Systems - Machine Electrical System Electrical System Components Diagram... 5.1.2 Electrical System Components.... 5.1.3 Engine Electrical Load Center: Engine Electrical Load Center
More information2-17 CABLE/HARNESS ROUTING SERVICE INFORMATION 1 IAC VALVE 2P CONNECTOR. 11 No.1 INJECTOR 2 TP SENSOR 3P CONNECTOR 2P CONNECTOR
CABLE/ ROUTING SERVICE INFORMATION 11 No.1 INJECTOR 2P 15 IAB CONTROL SOLENOID VALVE 2P 1 IAC VALVE 2P 2 TP SENSOR 3P JUNCTION (24P) MAIN WIRE to SWITCH WIRE 6P 16 CMP SENSOR 1 CMP SENSOR 2 4P 14 EBT SENSOR
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More informationINFORMATION DELLORTO IGNINTION SYSTEM HOW TO ASSURE FAULTLESS FUNCTION
INFORMATION DELLORTO IGNINTION SYSTEM HOW TO ASSURE FAULTLESS FUNCTION We have verified different complaints from the market regarding malfunctions of the ignition system. The following guideline should
More informationSupplement to Yanmar Kit Installation Instructions SAFETY
Supplement to Yanmar Kit Installation Instructions SAFETY This product is designed and intended only for use with a YANMAR engine. All safety and warning information contained in the Yanmar Operation Manual
More informationINSTRUCTION SHEET. Network Operations Center (NOC) Interface Instruction
INSTRUCTION SHEET Network Operations Center (NOC) Interface Instruction Model No. 006594-0* *Available as a kit prior to 2015. NOC Interface installed at factory beginning in 2015. DANGER Automatic start-up.
More informationThis is the layout of a typical harness form a TPI Camaro.
TPI wiring harness, typical 1986-89: This is the layout of a typical harness form a 1986-88 TPI Camaro. (A) bulkhead conn. through firewall. (B) ecm conn. (C) jct. conn for fuel injectors and cooling fan.
More information750 Paso Wiring Upgrade
750 Paso Wiring Upgrade Supplies required: 2 Bosch 30A/12V Relays # #0 332 209 150 (with mounting tab) 1 30 Amp fuse holder 1 10 Amp fuse holder 12 inches of brown 12 gauge wire 60 inches of red 14 gauge
More informationINSTALLATION MANUAL - v4
I-LOCKTM COUPLER INSTALLATION MANUAL - v4 SPECIAL NOTE Your new Wedgelock Coupler fitted with the I-LOCK TM Safety Device requires the installation of a third hydraulic line - please follow the instructions
More informationRCA PLUG KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RCA PLUG KIT P/N 2883824 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationMASS AIR FLOW (MAF) SENSOR, CHECKING - BOSCH
2004 Audi A6 Sedan (4B2) V6-2.7L Turbo (BEL) Vehicle > Powertrain Management > Computers and Control Systems > Testing and Inspection > Component Tests and General Diagnostics > Component Tests > Mass
More informationInstallation Instructions for Model CityFix
INTERLIFT Interlift, Inc. 15939 Piuma Ave. Cerritos, CA 90703 Tel: 888-774-5844 Fax: 562-924-8318 Installation Instructions for Model CityFix www.interlift.net 1. LIFT LOCATION The installation surface
More informationC WD 2 WHEEL LOW KIT FOR DODGE RAM 4WD VEHICLES
C18056-4WD 2 WHEEL LOW KIT FOR 1994-2002 DODGE RAM 4WD VEHICLES Pacbrake s 4WD 2 Wheel Low Kit allows the vehicle operator to engage the transfer case into 4WD low range without engaging the front wheel
More informationARTICLE BEGINNING INTRODUCTION IGNITION SYSTEM CAMSHAFT POSITION (CMP) SENSOR DISTRIBUTOR
Article Text Thursday, August 19, 1999 11:40PM ARTICLE BEGINNING 1996 ENGINE PERFORMANCE Volkswagen Removal, Overhaul & Installation - Gasoline Cabrio, Golf III, GTI, Jetta III, Passat CAUTION: When battery
More informationC TROUBLESHOOTING SIENNA (EWD613U) VOLTAGE CHECK CONTINUITY AND RESISTANCE CHECK
To Ignition SW IG Terminal Fuse SW 1 [A] [B] Voltmeter VOLTAGE CHECK (a) Establish conditions in which voltage is present at the check point. [A] - Ignition SW on [B] - Ignition SW and SW 1 on [C] - Ignition
More informationWired Real Time GPS Installation Instructions
Wired Real Time GPS Installation Instructions This page intentionally left blank. TABLE OF CONTENTS 1. Introduction 2 2. Selecting the Mounting Location for the Device. 3 3. Mounting the Device 5 4. Optional
More informationTRAILER MOUNTED PUMP MODEL B50 DRIVE CYLINDER CIRCUIT HYDRAULIC COMPONENTS & SCHEMATIC
DRIVE CYLINDER CIRCUIT HYDRAULIC COMPONENTS & SCHEMATIC PAGE 01 SINGLE SHIFT SWING TUBE CIRCUIT HYDRAULIC COMPONENTS & SCHEMATIC PAGE 02 DUAL SHIFT SWING TUBE CIRCUIT HYDRAULIC COMPONENTS & SCHEMATIC PAGE
More informationChevrolet Chevelle without Factory Air Control Panel Conversion Kit (473066)
an ISO 9001:2008 Registered Company 1966-67 Chevrolet Chevelle without Factory Air Control Panel Conversion Kit (473066) COLD TEMPERATURE FAN ON HOT DEFROSTER DE-ICE 18865 Goll St. San Antonio, TX 78266
More informationPart # Mopar LX Level 1 Air Suspension System
Part # 13040199 05-14 Mopar LX Level 1 Air Suspension System Front Components: 1 1304409 Front RQ ShockWave Kit for Stock Lower Arms Rear Components: 1 13044099 Rear CoolRide Kit 1 13040709 RQ Series Rear
More informationChevrolet Chevelle with Factory Air Control Panel Conversion Kit (473065)
an ISO 9001:2008 Registered Company 1966-67 Chevrolet Chevelle with Factory Air Control Panel Conversion Kit (473065) FAN HI INSIDE A/C OUTLETS COLD TEMPERATURE AIR OUTSIDE DEFROSTER DE-ICE HEATER HOT
More informationInstallation, Maintenance and Service Manual Power Cord
Installation, Maintenance and Service Manual Power Cord 45-081, REV. 8/14 1 of 8 Table Of Contents Section 1 Installation Procedure... 3 1.1 General...3 1.2 Sheave installation...4 1.3 Anchor installation...4
More informationSECTION 10 - ELECTRICAL
SECTION - ELECTRICAL Electrical Components, Upperstructure PAC551 - Series IV Highway Speed Excavators 8080001 Electrical Components, Upperstructure PAC56 8080001 Series IV Highway Speed Excavators - Electrical
More information1963 Chevrolet Impala Control Panel Conversion Kit (471063)
an ISO 9001:2008 Registered Company 196 Chevrolet Impala Control Panel Conversion Kit (47106) 18865 Goll St. San Antonio, TX 78266 Phone: 210-654-7171 Fax: 210-654-11 www.vintageair.com 901065 REV E 01/12/16,
More informationMD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version
MD10 Engine Controller Installation and User Manual for the MD10 Engine Controller. Full Version File: MartinMD10rev1.4.doc May 16, 2002 2 READ MANUAL BEFORE INSTALLING UNIT Receipt of shipment and warranty
More informationChevrolet Impala Control Panel Conversion Kit (471062)
an ISO 9001:2008 Registered Company 1961-62 Chevrolet Impala Control Panel Conversion Kit (471062) 20 30 40 50 60 70 80 90 100 110 120 C T E M P EF F U E L FAN DEF AIR HEAT 18865 Goll St. San Antonio,
More informationPH4000Ri/E Unit Ref # MFR # Stock Description Comments Discontinued
PH4000Ri/E PH4000Ri/E Unit Ref # MFR # Stock Description Comments Discontinued 1 7504 69449 Engine Assy (177F) 1 01 011501006 64510 Temperature Sensor, PH4000Ri/E 2 03030143 62366 M8 Flat Washer, White,
More informationChevrolet Chevelle with Factory Air Control Panel Conversion Kit (473063)
an ISO 9001:2008 Registered Company 1964-65 Chevrolet Chevelle with Factory Air Control Panel Conversion Kit (4706) COND TEMP DEF 18865 Goll St. San Antonio, TX 78266 Phone: 210-654-7171 Fax: 210-654-11
More informationBattery Control Center - Diesel
Service Manual CAUTION: All servicing of the Battery Control Center should be done only by a qualified Service Technician. Inadvertent shorts inside the Battery Control Center could result in severe damage
More informationInstruction Manual. P/N Suzuki GSXR1300 Hayabusa 6 Speed Plug & Play Adapter Harness
Instruction Manual P/N 30-3550 2002-2007 Suzuki GSXR1300 Hayabusa 6 Speed Plug & Play Adapter Harness OVERVIEW The 30-3550 AEM Infinity Adapter Kit was designed for the 2002 2007 Suzuki GSXR1300 Hayabusa.
More informationCHEV PICK-UP
an ISO 900: 2008 Registered Company 967-72 CHEV PICK-UP WITHOUT FACTORY AIR w/ FACTORY CONTROLS 473265 ACC-OFF-ON-START FAN TEMP OFF DASH COLD LO HI FLOOR DEF HOT 903273 REV D 4/3/5, 967-72 CHEV P-UP wo
More informationCUMMINS 6.7L EXHAUST BRAKE PRXB EXHAUST BRAKE KIT FOR 2007½-2015 TRUCKS EQUIPPED WITH 6.7L CUMMINS ISB DIESEL ENGINES. C Kit C Kit
CUMMINS 6.7L EXHAUST BRAKE PRXB EXHAUST BRAKE KIT FOR 2007½-2015 TRUCKS EQUIPPED WITH 6.7L CUMMINS ISB DIESEL ENGINES C44038 4 Kit C44039 5 Kit BEFORE STARTING THE INSTALLATION please read the entire installation
More informationC FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY
EXHAUST BRAKES C40019 1999-2003 FORD F250 / F350 7.3L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY Getting Started Thank you and congratulations on your purchase of a Pacbrake exhaust retarder.
More information850 TETHER SWITCH KIT
850 TETHER SWITCH KIT P/N 2883823 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More information1964 ½-66 Ford Mustang Control Panel Conversion Kit (471066)
an ISO 9001:2008 Registered Company 1964 ½-66 Ford Mustang Control Panel Conversion Kit (471066) Also Fits: 1964-65 Ford Falcon, Ranchero HEAT TEMP DEF 18865 Goll St. San Antonio, TX 78266 Phone: 210-654-7171
More informationInstallation Instructions General Motors 8.1 Sequential Vapor Injection (S.V.I.) System 7500/6500 Series Trucks model year.
Installation Instructions General Motors 8.1 Sequential Vapor Injection (S.V.I.) System 7500/6500 Series Trucks 2003-2005 model year. Technocarb Equipment (2004) Ltd. 4-30435 Progressive Way Abbotsford,
More informationPRXB EXHAUST BRAKE HIGH PERFORMANCE
HIGH PERFORMANCE PRXB EXHAUST BRAKE C44059, C4406, C44063, C44065 APPLICATION 994-2002 DODGE RAM AUTOMATIC TRUCKS EQUIPPED WITH 47RE TRANSMISSIONS WITH 5.9L, 24 VALVE CUMMINS DIESEL ENGINES GETTING STARTED
More informationThis information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
More informationWiring Harness Update Kit Assembly Instructions Treker 4200/4400 NT & ST Series Manual No M
Wiring Harness Update Kit Assembly Instructions Treker 4200/4400 NT & ST Series Manual No. 700-364M Before You Start! When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationPavement Services, Inc.
MG68 Parts Manual Pavement Services, Inc. Page 30 29 30 29 25 25 24 30 4 26 29 4 25 26 4 Page 2 The Decal Kit for the Model MG68 Maintainer is Item Part # Description 056859 DECAL, ANTI-FREEZE (BLACK)
More informationChevrolet Camaro without Factory Air Control Panel Conversion Kit
an ISO 900:205 Registered Company 967-68 Chevrolet Camaro without Factory Air Control Panel Conversion Kit 47568 8865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech
More informationHANDLEBAR BAG WITH PHONE CHARGER KIT
HANDLEBAR BAG WITH PHONE CHARGER KIT P/N 2883687; 2883786 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted
More information# and # FAST Fuel System Kits
1 INSTRUCTIONS #307500 and #307501 Fuel System Kits Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning the installation.
More informationCurrent parts on a ROTAX 125 MAX DD2 evo
Current parts on a ROTAX 125 MAX DD2 evo No. Part. No. Name Qty. USAGE for rework? 1 660 575 Pressure Line 220 mm 1 YES 2 666 816 Electronic Box DD2 1 YES 3 660 825 Ignition Coil 1 YES 4 664 630 Solenoid
More informationC40008 & C40009 EXHAUST BRAKES
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
More informationGrid Heater Starting Aid (T000)
Page 1 of 14 Topic No. Rev. Level Topic Date Group No. 94T13-2 01-May-1994 13 Expiration Date (U.S. and Canada): Expiration Date (International): Engine Family 6B, ISB, QSB5.9, B5.9 Fuel System Plant From
More information350 S. St. Charles St. Jasper, In Ph Fax
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 30154700 Big Red Analog Compressor Kit Components: 2 31920020 Thomas compressor 1 31915100 5 gallon aluminum
More informationCradlePoint Vehicle Best Practices Installation Guide
CradlePoint Vehicle Best Practices Installation Guide Using CradlePoint Routers in 12V and 24V Vehicles Revision 1.2 Overview The automotive environment can be particularly harsh for electrical equipment
More informationAEROMOTIVE Part # HP Hot Rod EFI Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 17150 700HP Hot Rod EFI Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that
More informationChevy Pickup Control Panel Kit
an ISO 9001:2008 Registered Company 1960-63 Chevy Pickup Control Panel Kit 473262 18865 Goll St. San Antonio, TX 78266 ph: 210-654-7171 fax: 210-654-3113 903258 REV C 9/19/14, INST 60-63 CHEV P-UP CNTRL
More informationSECTION 10 - ELECTRICAL
SECTION - ELECTRICAL Electrical Components, Upperstructure 6 6 TO CAB HARNESS BULKHEAD 9 WSH PWR WORK LT GND HEATER TEMP 6 CLUTCH-B CLUTCH-C 6 HORN 9 0 9 0 9 0 AC FAN- BOOM LTS TO UPPER PCB STR LEFT SGN
More informationTD 3.6 L4. Parts Manual. Deutz Engine. Telescopic Handlers. Gehl RS6-34 (Tier IV) Manitou MT6034 T (Tier IV)
TD 3.6 L4 Form No. 50960088 Revision A September 04 Deutz Engine Telescopic Handlers Gehl RS6-34 (Tier IV) Manitou MT6034 T (Tier IV) Parts Manual Introduction Deutz TD 3.6 L4 The Table of Contents pages
More informationP0102-MASS AIR FLOW SENSOR "A" CIRCUIT LOW
7 - D - RAM 5 PICKUP - 6.7L CUMMINS TURBO DIESEL P- SENSOR "A" CIRCUIT LOW BATT A FUSE 7 5A TOTALLY INTEGRATED C A8 8 RD/OR S A8 8 RD/OR A8 8 RD/OR FUSED B(+) RELAY RETURN 5 FUSED B(+) RELAY FEED RELAY-
More informationScion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N #
TURBO KIT Scion FR-S ZN6 Subaru BRZ ZC6 GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N # 11518000 Vehicle Type Chassis Code Engine Code Transmission Model Year Scion FR-S DBA-ZN6
More informationPage 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More information1969 Chevrolet Camaro with Factory Air Control Panel Conversion Kit (474269)
an ISO 900:2008 Registered Company 969 Chevrolet Camaro with Factory Air Control Panel Conversion Kit (474269) 8865 Goll St. San Antonio, TX 78266 Phone: 20-654-77 Fax: 20-654-33 www.vintageair.com 904269
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More informationControls Pack Installation Manual 2011 and newer 5.0L 4V and 5.4L 4V Engines
Please visit www.fordracingparts.com for the most current instruction and warranty information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationINSTALLATION MANUAL P2068. Level of Difficulty. Parts List. Product Image. Notes and Maintenance. Tools Required. Easy
INSTALLATION MANUAL P2068 Parts List 1 Grille guard 1 Driver / left frame mounting bracket 1 Passenger / right frame mounting bracket 1 Driver / left top mounting bracket 1 Passenger / right top mounting
More informationAutomatic Transmission Assembly Remove and Install (2,9 V6 24V engine) ( ) Remove
Automatic Transmission Assembly Remove and Install (,9 V6 4V engine) (7 4 0) Special Tools -40 Engine support bar -40-0 Adaptor for -40-40-03 Adaptor for -40 Workshop Equipment Transmission jack Materials
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationINTERNAL SURGE TANK TM
INTERNAL SURGE TANK TM Patent Pending Part Number: IST_RX7-9395 Foreword Thank you for purchasing an Internal Surge Tank. It will prevent fuel starvation during high performance driving conditions, without
More informationOPERATOR S MANUAL HWH COMPUTER-CONTROLLED 2000 SERIES LEVELING SYSTEM. FEATURING: Single Step Touch Panel Control Air Leveling
OPERATOR S MANUAL HWH COMPUTER-CONTROLLED 000 SERIES LEVELING SYSTEM R HWH CORPORATION R FEATURING: Single Step Touch Panel Control Air Leveling HWH COMPUTERIZED LEVELING LEVEL AIR EXCESS SLOPE MODE DUMP
More informationRetriever 5800G/P/D. revised 2/01 Form Number
Retriever 5800G/P/D PARTS LIST Advance MODELS 56482005, 56482010, 56482015 This parts list is for machines after serial number 221134 All models covered in this manual are OBSOLETE revised 2/01 Form Number
More informationProduct Support Bulletin
MODEL: SUBJECT: C2 BODY DEACTIVATION DOOR BUZZER, AIR DOOR W/ EXTERNAL KEY SWITCH DATE: DECEMBER 10, 2007 INDEX: C2 5 PAGE: 1 OF 6 DO NOT USE THIS PROCEDURE. INDEX C2 5, BULLETIN 5 IS NOW OBSOLETE AND
More informationSTX-38 EFI Stump Grinder with Intelli-Sweep
Form No. 3421-244 Rev A STX-38 EFI Stump Grinder with Intelli-Sweep Model No. 23214 Serial No. 402000000 and Up Register at www.toro.com. Original Instructions (EN) *3421-244* A Ordering Replacement Parts
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi These instructions are based on a vehicle with an OEM turbocharger and top-mount intercooler. If a front-mount
More informationCHEV P-UP CONTROL PANEL CONVERSION KIT an ISO 9001:2008 Registered Company
an ISO 900:2008 Registered Company 973-87 CHEV P-UP CONTROL PANEL CONVERSION KIT 473274 DASH FLR DEF 903274 REV B 9/8/4, 73-87 CHEV P-UP CNTRL PNL INST PG OF 9 Table of Contents PAGES. 2. 3. 4. 5. 6. 7.
More information75/90 FOURSTROKE EFI WIRING DIAGRAM
75/0 FOURSTROKE EFI WIRING DIAGRAM 0-87725 MARCH 2005 Page 8A-3 75/0 FourStroke EFI Wiring Diagram - Electronic control module (ECM) 2 - Engine water temperature sensor 3 - Ignition coil for cylinder #
More informationChevrolet Full-Size 3-Lever Control Panel Conversion Kit (473059)
an ISO 900:2008 Registered Company 955-56 Chevrolet Full-Size -Lever Control Panel Conversion Kit (47059) 8865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech Support:
More informationCHEV PICK-UP
an ISO 9001: 2008 Registered Company 1964-66 CHEV PICK-UP WITHOUT AC w/ DELUXE CONTROL PANEL CONVERSION KIT 47264 DEF AIR FAN HEAT 90264 REV C 4/1/15, 1964-66 CHEV P-UP wo AC w/ DELUXE CONTROL PANEL KIT
More information1956 Ford Passenger Car Control Panel Conversion Kit (473150)
an ISO 900:2008 Registered Company 956 Ford Passenger Car Control Panel Conversion Kit (47350) 8865 Goll St. San Antonio, TX 78266 Phone: 20-654-77 Fax: 20-654-33 www.vintageair.com 900505 REV B 04/4/5,
More informationBX88175 Installation Instructions ToadStop II Vacuum Brake System
BX88175 Installation Instructions ToadStop II Vacuum Brake System Serial No. Customer supplied tools & supplies Utility knife, 12VDC tester, drill & bits: (1/8", 1/4", 5/8 ), ¼ socket drive bit, punch,
More informationOCTOPUS SELECTION & INSTALLATION GUIDE Rev. C CRA SERIES CONTINUOUS RUNNING PUMPSET
A. GENERAL DESCRIPTION: OCTOPUS SELECTION & INSTALLATION GUIDE Rev. C CRA SERIES CONTINUOUS RUNNING PUMPSET Octopus CRA continuous running pumps are very reliable quiet and efficient devices which will
More informationINSTALLATION INSTRUCTIONS Dodge Ram Crew / Mega 2500/3500 2/4WD NOTE: (tow hooks will not be re-attached) PART # P5056
INSTALLATION INSTRUCTIONS 2010-14 Dodge Ram Crew / Mega 2500/3500 2/4WD NOTE: (tow hooks will not be re-attached) PART # P5056 PARTS LIST: Qty Description Qty Description 1 Grill Guard Bar 6 12mm x 30mm
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationCHEV PICK-UP
an ISO 9001: 2008 Registered Company 1967-72 CHEV PICK-UP WITHOUT AC CONTROL PANEL CONVERSION KIT 47266 ACC-OFF-ON-START DEF AIR FAN HEAT 90271 REV D 4/1/15, 1967-72 CHEV P-UP wo AC CONTROL PANEL KIT PG
More informationInstallation Instructions For 50330, 50331, 50332, and Off Road Switch Panels
Installation Instructions For 50330, 50331, 50332, and 50333 Off Road Switch Panels 2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 Phone 817-244-4024 Fax 888-350-6588 Sales 800-423-9696 Tech
More informationthe systems people Owners Manual VCMS Switch Panel System Model VCMS-SP34
Owners Manual VCMS Switch Panel System Model VCMS-SP34 1. Product Description The Switch Panel System consists of a eight-position switch module, two six-output power modules and a 10 ft. communications
More informationELECTRIC SCHEMATICS LS1 LS2. "1532ES / 1932ES" Service & Parts Manual - ANSI Specifications March 2008 Page 5-9 ART_2236 ART_2243
ELECTRIC SCHEMATICS NOTES: (Unless otherwise specified). Switch S BASE/PLATFORM makes contact from the CENTER to the LEFT position when placed in BASE.. Switch S UP/DOWN makes contact from the CENTER to
More informationBanks Brake. with installation instructions EXHAUST BRAKE SYSTEM Dodge 5.9L Cummins (12-valve) Turbo-Diesel Pickups with Manual Transmissions
OWNERS MANUAL with installation instructions Banks Brake EXHAUST BRAKE SYSTEM 1994-98 Dodge 5.9L Cummins (12-valve) Turbo-Diesel Pickups with Manual Transmissions THIS MANUAL IS FOR USE WITH SYSTEMS 55217
More informationGeneral Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools
TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationInstallation Instructions for: EMS P/N Toyota Supra
Installation Instructions for: EMS P/N 30-1130 1989-1992 Toyota Supra! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with EXTREME caution! The AEM EMS System
More informationRetriever /00 revised 5/06 FORM NO All models covered in this manual are obsolete.
PARTS LIST Advance MODELS 5648000 (propane after SN 4504), 564800 (gas after SN 45898), 564800 (dual fuel after SN 4504), 564800 (diesel) Nilfisk MODELS SR 800 can now be found in PL560444 All models covered
More informationP3066 INSTALLATION MANUAL
P3066 INSTALLATION MANUAL Parts List 1 Grille guard 1 Driver / left frame bracket Level of Difficulty Moderate Scan for helpful install tips 1 Passenger / right frame bracket 1 Driver / left top bracket
More informationDENSO R5 Starter Installation Guide For:
DENSO R5 Starter Installation Guide For: 2006 International 9400i Cummins ISX Engine LA990009-2054 1/ 25 This guide will assist the technician with the installation of the R5 starter on this particular
More informationPart # Galaxie Level 1 Complete Air Suspension System
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 12160199 60-64 Galaxie Level 1 Complete Air Suspension System Front Components: 1 12162409 Front RQ Series
More informationGen III HEMI Harness PN or
Gen III HEMI Harness PN 558-106 or 558-107 This wiring harness interfaces a Holley EFI ECU to a Gen III HEMI engine. It is meant to be used in conjunction with an injector harness, a coil harness, and
More information1968 Mopar B-Body Control Panel Kit
an ISO 9001:2008 Registered Company 1968 Mopar B-Body Control Panel Kit 474154 18865 Goll St. San Antonio, TX 78266 Phone: 210-654-7171 Fax: 210-654-3113 www.vintageair.com 901309 REV B 9/18/14, PG 1 OF
More informationCAMARO. w/ & w/o AC CONTROL PANEL CONVERSION KIT an ISO 9001:2008 Registered Company
an ISO 9001:2008 Registered Company 1970-81 CAMARO w/ & w/o AC CONTROL PANEL CONVERSION KIT 473071 903071 REV B 9/18/14, INST. GEN IV 1970-81 CAMARO w/ & w/o AC CNTRL PNL PG 1 OF 9 Table of Contents PAGES
More informationIMPCO ECOTRANS TECHNOLOGIES L.P. PARTS CATALOG K9.9 SERIAL # UP TO AND TO
IMPCO ECOTRANS TECHNOLOGIES L.P. PARTS CATALOG K. SERIAL # UP TO 00 AND 0 TO 0 IMPCO ECOTRANS TECHNOLOGIES INC TABLE OF CONTENTS K. RAIL APU Mounting/Enclosure/Engine/Engine Mount (High Profile).............
More information