Range Hoods Removing Control Switches Removing Blower Motor Wiring Diagrams

Transcription

1 K39 Technical Education ange Hoods emoving Control Switches emoving Blower Motor iring Diagrams KitchenAid Jenn-Air hirlpool Prepared by: HILPOOL CONSUME CAE Job Aid

2 FOAD This ange Hood Controls and Motor Access Guide ( ), provides the In-Home Service Professional with information on how to access the control switch(es) and exhaust motor on range hoods. For specific information on the model being serviced, refer to the information supplied with the range hood. Always use the Tech Sheet supplied with the product when servicing the range hood. GOALS AND OBJECTIVES The goal of this Job Aid is to provide information that will enable the In-Home Service Professional to properly gain access to the control switch(es) and exhaust motor of range hoods. The objectives of this Job Aid are to: Understand and follow proper safety precautions. Successfully access control or motor components that require repair or replacement. Successfully return the range hood to its proper operational status. HILPOOL COPOATION assumes no responsibility for any repairs made on our products by anyone other than authorized In-Home Service Professionals. egistered trademark of hirlpool, U.S.A., KitchenAid, U.S.A., Jenn-Air, U.S.A., or Maytag Corporation or its related companies. MAGIC CHEF is a registered trademark of CNA International, used under license All rights reserved. i

3 CONTENTS Page GOALS AND OBJECTIVES...i SAFET FIST...iii ANGE HOODS... 1 GX7330DX, GX7336DX...1 GX7330DX, GX7336DX IING DIAGAM....2 JXI5030S, JXI5036S JXI5030S, JXI5036S IING DIAGAM....5 JX9030S, JX9048S, JX9036S....6 JX9030S, JX9048S, JX9036S IING DIAGAM....7 KXI2536SS, KX2530SS, KX2548SS....8 KXI2536SS IING DIAGAM KXU4236SS, KXU4230SS KXU4236SS, KXU4230SS IING DIAGAM KXU8030SS, KXU8036SS KXU8030SS, KXU8036SS IING DIAGAM KX2336SS, KX2330SS KX2336SS, KX2330SS IING DIAGAM KXI4336SS, KXI4342SS, KX4336SS, KX4330SS, KX4436SS, KX4430SS KXI4336SS, KXI4342SS, KX4336SS, KX4330SS, KX4436SS, KX4430SS IING DIAGAM. 22 KX8730SS, KX8736SS, KX8748SS KX8730SS, KX8736SS, KX8748SS IING DIAGAM KXI9736SS, KXI9748SS KXI9736SS, KXI9748SS IING DIAGAM IN-LINE, INTENAL AND EXTENAL BLOE SSTEMS INTENAL BLOE SSTEMS UXB0600D, UXB1200D IN-LINE BLOE SSTEMS UXI0600D, UXI1200D EXTENAL BLOE SSTEMS KPEU722M, KPEC922M KPEU722M, KPEC922M IING DIAGAM ADDITIONAL ANGE HOOD IING DIAGAMS JXI8042, JXI8036, JXI8242, JXI8236 Jenn-Air JX5030S, JX5036S Jenn-Air JX6030, JX6036 Jenn-Air JX8030, JX8036, JX8042 Jenn-Air JX8230, JX8236 Jenn-Air JX8836 Jenn-Air JX9030S, JX9036S, JX9048S Jenn-Air KXI9736, KXI KXU2830 KitchenAid KXI2536, KXI2536 KitchenAid UXL6048SS,UXL6036SS UXG7360VD, UVG73660VD iii

4 SAFET FIST NOTICE TO THE TECHNICIAN It is the responsibility of the Service Technician to comply with all EPA egulations and Standards and posses all necessary State and Federal licenses when servicing refrigerators. Federal regulations and Standards can be found on the United States Government EPA eb Site. State egulations and Standards and licensing requirements, in most cases, can be found on the State Government eb Site. iii

5 GX7330DXS, GX7336DX hirlpool Filters Control 2 Filters Hood is shown from underside removed from Installation 5. emove (2) T10 Torx screws, one (shown in figure 3) and one on the other side of the box. emove (2) screws Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. Figure 3 6. Pull the top of the box open slowly. The top of the box is attached by sheet metal hinges that will break easily, see figure emove (3) T10 Torx screws from the bottom of the box to release ease the plastic switch box, see figure 5. Bend top at this fold (hinges) emove (3) screws emove These Screws Figure 1 To remove the control: 1. Disconnect power to the range hood. 2. emove the filters. 3. emove (2) T10 Torx screws screws screws from the under side of the frame at the right corner of the hood, see figure Pull the metal control housing out through the filter opening, see figure 2. Figure 4 Figure 5 Figure 6 8. emove cover to access wire connections, see figure 6. Figure 2 1

6 GX7330DXS, GX7336DX (continued) iring Diagram Junction box L GNDN SE11PA -G Ballast EMI Filter -G -G 15uF 25uF Motor esistance (Ohms) B G Blue - ed Blue - Black uF Motor Characteristics Power Supply Frequency 120 VAC 60 HZ B G -G -G Power Absorption 144 Current 1.2A Installation Instructions

7 JXI5042S, JXI5036S Motor Housing Jenn-Air 5. Disconnect harness. 6. emove strain relief from the control panel. See figure emove two (2) T10 Torx screws that mount the display to the bracket. LCD Display Harness Connector Harness Strain elief LCD Display with Bracket Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. Figure 3 To remove the motor: 1. Disconnect power to the range hood. 2. emove the range hood from the installation. 3. emove the glass. See figure emove the foam insulation from around the top of the range hood flue. See figure 4. Foam Insulation Vent Hood Top To remove the LCD display: 1. Disconnect power to the range hood. 2. emove the range hood from the installation. Glass emove These Screws Glass etainer Figure 1 Bracket 3. emove four (4) T10 Torx screws that secure the two (2) glass retainer brackets. 4. emove two (2) T10 Torx screws from control bracket. See figure 2. Intake Cover Flue Figure 4 5. emove two (2) thumb screws to release intake cover at the bottom of the unit. See figure emove filter. See figure 5. Filter emove These Screws Figure 2 3 Thumb Screws Figure 5

8 JXI5042S, JXI5036S (continued) Jenn-Air Top of Hood Foam Insulation Key Hole Slot Figure 6 7. emove (4) T10 Torx screws one in each corner of the filter guard, see figure 6. Figure 8 T20 Torx emove These Screws Figure 7 8. emove (4) T10 Torx screws from the motor mounting plate, see figure 7. NOTE: It is recommended that an extention be used with the screw driver because these screws are difficult to reach. Screws also may be obstructed by insulation. If this is the case, move the insulation out of the way and replace it when reassembling. Back of Motor removed from Hood Figure 9 9. Loosen or remove (2) T20 Torx screws (one on each side) that mounts the motor into key hole slots at the top of the range hood, see figure 8 and 9. NOTE: The key hole screws are covered by a piece of foam insulation. Be sure to replace the insulation when reassembling. 10.Position the motor so that the screw heads clear the key hole slots and remove the motor. 4 Figure 10

9 JXI5042S, JXI5036S (continued) Jenn-Air iring Diagram IING BOX L N Electronic User Interface CON2 - G -G Electronic Power Board CON1 TANSFOME CON3 N L NL NM P1 P2 P4A P3 P4 LA P5 S3 S2 S1 P8 P7 P CON4 S E C P I B B B G ATTENTION!: ADDITIONAL LAMPS ONL PESENT ON THE VESIONS ITH 4 LAMPS SEC PI TANSFOME B B - G - G G G 1 -G B Installation Instructions

10 JX9030S, JX9036S, JX9048S Jenn-Air Knobs 4. emove the knobs 5. emove the center shaft nuts securing the switches in place. 6. The switches can be removed and disconnected. Locator Pin Locator Hole Front Panel (Hologen Lights) Figure 2 NOTE: Be sure to note the position of the locator pins on each switch and orient the switches properly when reassembling, see figure 2 and 3. Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. HALOGEN LIGHTS Switch functions Figure 3 INCANDESCENT LIGHTS FAN To remove switches: 1. Disconnect power to the range hood. 2. emove the air filters 3. emove (2) T10 Torx screws from the underside of the front panel. This is the panel that accommodates the incandescent lights see figure 1. Figure 1 6

11 JX9030S, JX9048S, JX9036S Jenn-Air iring Diagram IING BOX L N Electronic User Interface CON2 - G -G Electronic Power Board CON1 TANSFOME CON3 N L NL NM P1 P2 P4A P3 P4 LA P5 S3 S2 S1 P8 P7 P CON4 S E C P I B B B G ATTENTION!: ADDITIONAL LAMPS ONL PESENT ON THE VESIONS ITH 4 LAMPS SEC PI TANSFOME B B - G - G G G 1 -G B Uses a supplemental blower system Installation Instructions

12 KXI2530SS, KX2536SS, KX2548SS Kitchen Aid 5. emove the glass and frame and place it in a secure location. Glass and Frame Motor NOTE: Visually center glass around box (duct) when reassembling. 6. emove (2) T20 Torx screws from the control, see figure 2. Screws Filter Control Figure 2 7. Disconnect harness and remove control, see figure 3. Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. To remove control: 1. Disconnect power to the range hood. 2. emove the hood from installation. 3. emove the filters. 4. emove (4) T20 Torx screws that secure glass hold down brackets (2) screws on either side of the motor housing base, see figure 1. Connectors Figure 3 Control Motor Housing glass hold down bracket Glass Figure 1 8

13 KXI2530SS, KX2536SS, KX2548SS (continued) Kitchen Aid To remove motor: 1. Disconnect power to the range hood. 2. emove the filters. 3. Disconnect the harness. 4. emove (4) 1/4 screws from the motor mounting bracket, see figure 1. Motor Screws Motor Connector Figure 1 NOTE: It is recommended that a screwdriver extension be used because these screws are difficult to reach. 9

14 KXI2530SS, KX2536SS, KX2548SS (continued) Kitchen Aid iring Diagram L GND /G N EMI Filter B (Line) (Neutral) (Lamp) (Speed 1) (Speed 2) G (Speed 3) AGC Mechanical Push Buttons ith Back Light Switch Operation Position Off Connection No Connection B /G Lamps Low Speed Medium Speed High Speed Black - ellow (1-3) Black - hite (1-4) Black - ed (1-5) Black - Gray (1-6) /G 12.5uF B /G G B Transformer Transformer 120V 12V 120V 12V /G Motor Characteristics Power Supply 120 V AC Motor esistance (Ohms) Blue - ed 37.7 Frequency 60 Hz Blue - Gray 30.3 Power Absorption 240 Blue - Black 28.8 (max) Blue - hite 45.1 (min) oom Temp. 73 F (23 C) Installation Instructions

15 KXU4236SS, KXU4230SS Kitchen Aid 4. emove (2) T20 Torx screws, one from each side of the light panel, see figure 2. 3 Filters Control T20 Torx Figure 2 Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. To remove the control: 1. Disconnect power to the range hood. 2. emove the filters. 3. emove (4) T10 Torx screws from under the frame, (2) screws at the corner of each side panel, see figure 1. Figure 3 ibbon Cable 5. Disconnect the ribbon cable behind the light panel and remove the panel, see figure 3. Figure 4 6. emove (2) T10 Torx screws that secure the switch housing to the frame, see figure emove e (4) screws that t secure the board to the switch housing, see figure 5. Disconnect ribbon cable. T10 Torx Figure 1 11 ibbon Cable Figure 5

16 KXU4236SS, KXU4230SS (continued) Kitchen Aid To remove the motor: 1. Disconnect power from the range hood. 2. emove the filters. 3. emove (4) 1/4 hex head phillips screws from the motor mounting bracket, see figure 1. Screws Figure 1 4. Slightly rotate and reposition the motor to disengage the stamped metal ears that mate with opening in the motor mounting bracket, see figure 2 and 3. Locking Tabs ( Ears ) Figure 2 Locking Tabs Openings ( Ears ) Figure 3 5. Disconnect electrical plug from the printed circuit board. 12

17 KXU4236SS, KXU4230SS (continued) Kitchen Aid iring Diagram L GND N Electronic User Interface LCD /G Electronic Power Board BE1CAA N L N N N L A S 4 S3 S2 S Motor esistance (Ohms) / 18 /G uf / 9.8 (max) 120 V 12 V / oom temp (min) 73.4 F (23 C) Transformer G G B B /G /G Motor Characteristics Power supply Frequency 120 VAC 60 Hz M S50 Power absorption 420 Current 3.7 A Installation Instructions

18 KXU8030SS, KXU8036SS Kitchen Aid 4. emove (2) T10 Torx screws that secure the switch box to the light panel, see figure 2. 2 Filters Control Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. Figure 2 5. emove the switch housing from the light panel. To remove the control: 1. Disconnect power from the range hood. 2. emove the filters. 3. emove (4) T10 Torx screws from backside of the light panel, see figure 1. Figure 3 6. emove (4) T10 Torx screws that attach the cover to the switch box assembly, see figure 4. Screw Locations Figure 1 Switches Figure 4 7. Test and or replace the affected switch. 14

19 1. To remove the motor: a. Disconnect power to the range hood. b. emove the filters. c. Disconnect quick disconnect plug. KXU8030SS, KXU8036SS (continued) Kitchen Aid Quick Disconnect emove These Screws Figure 1 d. emove (4) hex head phillips screws from the 2 motor or mount brackets, see figures 1 and 2. emove These Screws Figure 2 15

20 KXU8030SS, KXU8036SS (continued) Kitchen Aid iring Diagram Junction Box GND L N /G B On Off Fan Speed Fan Light Off Motor esistance (Ohms) Blue - ed 18 G B B Blue - Gray 14.3 Speed 3 Speed 2 Blue - Black 9.8 (max) Speed 1 Blue - hite oom Temp (min) 41 F (23 C) 25uF B Temperature Sensor B Motor Characteristics G B /G Power Supply 120 VAC Frequency 60 HZ G B /G Power Absorption 420 Current 3.7A Installation Instructions

21 KX2330SS, KX2336SS Kitchen Aid 5. Disconnect the control harness, see figure 2. Control Harness Connector Filters Control Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. Figure 2 To remove the motor: 1. Disconnect power from the range hood. 2. emove the filters. 3. Disconnect control and harness connector, see figure 3. Harness Connector To remove the control: 1. Disconnect power to the range hood. 2. emove the filters. 3. emove (2) T10 Torx screws from the right underside of the light panel, see figure 1. Control Figure 3 4. emove (4) T10 Torx screws from the motor mounting plate (2) on each side, see figure Disengage locating ears from the slots at the back of each bracket, see figure 4. emove These Screws Ears Screws Figure 1 4. The control can now be easily accessed, see figure 2. Ears Left side of motor Figure 4 ight side of motoro 17

22 6. Pull motor out, see figure 3. KX2336SS, KX2330SS (continued) Kitchen Aid 8. emove (2) T10 Torx screws and disengage (2) tabs that secure the wiring harness cover, see figure 5. Tabs Figure 3 7. emove (6) T10 Torx screws that mount the electrical housing around the motor, see figure 4 and 4a. Figure 5 9. Disconnect motor wiring harness from connector block and remove motor, see e figure 6. Connector Block Motor iring Harness Screws Figure 4 Screws Figure 6 Screws Figure 4a 18

23 KX2336SS, KX2330SS (continued) Kitchen Aid iring Diagram Junction box L GND N 1 2 (Line) (Neutral) AGC (Lamp) (Speed 1) Mechanical pushbuttons with back light 5 (Speed 2) /G 6 G (Speed 3) Switch operation /G EMI Filter B 1 B G 5 6 G Motor resistance (Ohms) / 37.7 /G 30.3 / 28.8 (max) Position Connection Off Lamps Low speed Medium speed No connection / (1-3) / (1-4) / (1-5) / 45.1 (min) High speed /G (1-6) oom temp F (23 C) Motor characteristics Power supply 120 VAC Frequency 60 Hz Power absorption 240 B B 12.5 uf Transformer 120 V 12 V /G G /G /G N G Installation Instructions

24 KXI4336SS, 36SS, KXI4342SS, KX4336SS, KX4330SS, KX4436SS, KX4430SS Motor Kitchen Aid 4. emove (4) T10 Torx screws, (2) from each side ofthe light panel, total of (4), see figure 2. Light Panel Light Switch 2 Filters Control Figure 2 5. emove (2) T10 Torx screws, that secure the on/off switch bracket to the frame, see figure 3. Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. Screws On/Off Switch To remove the light switch and control: 1. Disconnect power from range hood. 2. emove the filters. 3. emove (2) T10 Torx screws each from the right and left of side panels total of (4), see figure 1. Figure 3 6. Depress the switch retainers and pull the switch out the front of the panel. See figure 4. Light Switch emove these screws Side Panels Strain elief Switch Bracket Figure 1 20 Figure 4

25 KXI4336SS, KXI4342SS, KX4336SS, KX4330SS, KX4436SS, KX4430SS (continued) Kitchen Aid 7. emove (2) T10 Torx screws to release the control bracket, see figure 5. emove Screws at these Locations Control Bracket Figure 5 8. emove (2) T10 Torx screws from the control box cover, see figure 6. emove Screws at these Locations ibbon Connector Figure 6 9. emove (4) T10 Torx screws from the Electronic User Interface board and disconnect ribbon connector, see figure 6. 21

26 KXI4336SS, KXI4342SS, KX4336SS, KX4330SS, KX4436SS, KX4430SS (continued) Kitchen Aid iring Diagram IING DIAGAM Motor Characteristics Power Supply Frequency 120 VAC 60 Hz Motor esistance (Ohms) Blue - ed Blue - Gray Blue - Black (max) Power Absorption 420 Blue - hite 21.6 (min) Current 3.7 A oom Temp. 73 F (23 C) Installation Instructions

27 KX8730SS, KX8736SS, KX8748SS KitchenAid 5. emove (2) screws, one on each side of the filter retainer panel, remove the panel, see figure 3. 2 Filters Control emove These Screws Figure 3 6. emove e (2) screws, one at on each side of the control switch, see e figure 4. Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. To remove the control switch: 1. Disconnect power from range hood. 2. emove the filters. 3. emove e (4) T20 screws along the underside edge of the front filter retainer, see figure 1. Front Filter etainer Panel emove These Screws Figure 4 7. emove the control switch from the light panel. Figure 1 4. emove (2) screws, one at each end of the front filter retainer panel, see figure 2. Figure 5 Screw Locations Figure 2 23 Switches Figure 6

28 KX8730SS, KX8736SS, KX8748SS (continued) iring Diagram Junction box N L Gnd SE112A -G On Off On Off 2 1 Off Fan speed Fan speed Fan speed Fan Light G G B B B Closure temperature: 167 F±5.4 F (75+/-3 C) Opening temperature: 140 F (60 C) Temperature sensor Speed 2 Speed 3 Speed 1 G uF B B 25uF B B G -G G /G Lamps Optional kit with 1 motor Motor esistance (Ohms) Motor Characteristics Blue-ed: 18 Blue-hite: 21.6 (min.) Blue-Black: 9.8 (max) Power supply: 120 VAC Power absorption: 420 Blue-Gray: 14.3 oom Temp: 73.4 F (23 C) Frequency: 60 Hz Current: 3.7A Switch operation with button Position Connection Action Speed 1 Speed 2 Speed 3 3 Switch operation with button ON-OFF Position Connection Action 4 Motor ON Motor OFF Switch operation with button Light Position ON OFF OFF 1 2 Connection Action Lights Off Low Intensity High Intensity Installation Instructions

29 KXI9736SS, KXI9748SS Kitchen Aid Motor 4. Pull the control out from the back of the panel, see figure emove (6) T10 Torx screws from the control switch cover, see figure 2. Control 3 Filters Figure 2 Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. To remove the control: 1. Disconnect power from the range hood. 2. emove the filters. 3. emove (2) T10 Torx screws that mount the control, see figure 1. Figure 3 6. emove and/or replace the switch(es) as needed. NOTE: Some models may require that a separate blower motor is purchased to meet the installation specifications. Figure 1 25

30 Junction box N L Gnd G KXI9736SS, KXI9748S (continued) Kitchen Aid IING iring DIAGAM Diagram SE110A Fan speed Fan speed On Off Fan On Off Fan B Closure temperature: 167 F±5.4 F (75+/-3 C) Opening temperature: 140 F (60 C) Temperature sensor 25uF Speed 1 Speed 2 Speed 3 25uF B B B B G /G 2 1 Off Light G G B B G G -G Lamps Optional kit with 1 motor Motor esistance (Ohms) Motor Characteristics Blue-ed: 18 Blue-hite: 21.6 (min.) Blue-Black: 9.8 (max) Power supply: 120 VAC Power absorption: 420 Blue-Gray: 14.3 oom Temp: 73.4 F (23 C) Frequency: 60 Hz Current: 3.7A Switch operation with button Position Connection Action Speed 1 Speed 2 Speed 3 3 Switch operation with button ON-OFF Position Connection Action 4 ON OFF Position Motor ON Motor OFF Switch operation with button Light Connection Action OFF Lights Off Low Intensity High Intensity Installation Instructions

31 NOTES 27

32 In-Line, Internal and External Blower Systems These are dedicated blowers designed to work with the range hood models listed below. Blower models and mounting locations are determined at the time of installation. Blowers are matched to range hood models based on individual installation requirements. ange Hood Models (requires one of the listed blower models KXI9736 KXI9748 KX8730 KX8736 KX8748 KX9736 KX9748 UXL6036 UXL6048 ange hood models and detecated blower assemblies Internal Blower Models (inside frame of hood) UXB0600D (600 CFM) UXB1200D(1200 CFM) In-Line Blower Models (outside the frame of the hood, but in the exhaust vent system) UXI0600D (600CFM) UXI1200D (1200 CFM) External Blower Models (outside the house) KPEU722M (600CFM) KPEC922M (1200 CFM) 28

33 Internal Blower Systems UXB0600D, UXB1200D, UXI600D, UXI1200D Single Internal Blower Motor Assembly 3. Disconnect the motor wiring harness from the locations shown for a single or Dual blower motor system. See marked locations A. Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. A A. iring connection Internal Dual Motor Assembly Dual Blower Motor Assembly A UXB0600D (600 CFM) bracket. A. iring connection 4. Slide the left mounting plate flange from under the motor mounting bracket. UXB1200D (1200 CFM) To remove internal blower motor: 1. Disconnect power to the range hood. 2. emove the internal blower motor assembly inside the hood liner canopy. 29 A B A. Motor mounting bracket B. Mounting plate left flange

34 Internal Blower Systems (continued) UXB0600D, UXB1200D 5. emove 6 x 16 mm screws and 6.4 mm lock washers (quantity 2 for single motor; quantity 5 for dual motor). A 8. Pull the right end of the motor mounting plate down and unsnap it from the spring tab. NOTE: The spring tab should be outside the slot in the mounting plate. mounting plate. A B A. Motor mounting plate hole B. Power supply wires and connector 6. emove the power supply wires and connector from the range hood through the hole in the right end of the motor mounting plate. A. Motor mounting plate B. Spring clip B 5. A B A. iring box connector B. Power supply connector from range hood 7. Disconnect power cord connector from the range hood to connector on wiring box. C B A A. Screw with lock washer B. Mounting hole in motor mounting plate C. Clip nut (6 mm) 30

35 In-Line Blower Systems UXI0600D, UXI1200D 5. emove the screws that secure the blower motor assembly to the in-line blower housing and set them aside. 6. Pull the spring clip to release the blower motor assembly. emove the blower motor assembly from the housing and place it on a covered surface. Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. To emove In-Line blower system: A B C Excessive eight Hazard Use two or more people to move and install in-line blower motor system. Failure to do so can result in back or other injury. D A. Front cover B. Blower mounting screws C. Spring clip D. Bottom housing mounting holes E. Motor electrical plug UXI0600D (600CFM), UXI1200D (1200 CFM) emoving an In-Line Blower System: 1. Disconnect power to the range hood. Use two or more people, to remove the in-line blower motor system from the mounting location. 2. emove the 10 screws from the front cover of the in-line blower motor housing. 3. emove the front cover of the in-line blower motor housing and set it aside. NOTE: To make the blower motor housing easier to remove, the blower motor assembly can be removed first. 4. Disconnect the motor electrical plug from the blower motor assembly. 31

36 NOTE: The blower motor housing can be mounted using 4 holes from either the inlet side or the outlet side of the blower. Outlet Side A In-Line Blower Systems (continued) UXI0600D, UXI1200D A Disconnect Electrical Connections for In-Line Blower Motor System 1. Disconnect power. 2. Disconnect the wires from the wiring conduit leading to the wires from the motor electrical plug cable inside the in-line blower housing terminal box. A B C A A D E F G H I A Inlet Side A A. UL listed or CSA approved ¹ ₂" (1.3 cm) wiring conduit B. UL listed wire connectors C. Black wires D. hite wires E. ed wires F. Blue wires G. Gray wires H. Green (or yellow/green) and green/yellow wires I. Motor electrical plug cable A. Mounting holes 1. Detach the in-line blower motor housing from the mounting location by removing four 6 x 80 mm mounting screws and washers. 32

37 External Blower Systems KPEU722M, KPEC922M Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. Figure 3 Excessive eight Hazard Use two or more people to move and install in-line blower motor system. Failure to do so can result in back or other injury. Parts List Black Plastic Collar KPEU722M (600CFM) KPEC922M (1200CFM) To access the external blower motor: 1. Disconnect the power to the In-Line blower. 2. emove the blower housing cover. Motor and Fan Assembly Blower Housing Cover 3. Disconnect the vent work from the exterior blower s black plastic vent collar lar and remove duct tape as needed. 4. emove the wiring box cover and disconnect the 120-volt power supply cable at the strain relief. 5. emove wire connectors and disconnect the iring. (See FIGUE 3 and wiring diagram.) Using twist-on connectors: Disconnect white wires. Disconnect black wires. Disconnect the green power supply wire. 33

38 External Blower Systems (continued) KPEU722M, KPEC922M iring Diagram Installation Instructions

39 Additional ange Hood iring Diagrams ADDITIONAL ANGE HOOD IING DIAGAMS JXI8042, JXI8036, JXI8242, JXI8236 Jenn-Air...36 JX5030S, JX5036S Jenn-Air...37 JX6030, JX6036 Jenn-Air...38 JX8030, JX8036, JX8042 Jenn-Air...39 JX8230, JX8236 Jenn-Air...40 JX8836 Jenn-Air...41 JX9030S, JX9036S, JX9048S Jenn-Air...42 KXI9736, KXI KXU2830 KitchenAid...44 KXI2536, KXI2536 KitchenAid...45 UXL6048SS,UXL6036SS...46 UXG7360VD, UVG73660VD

40 Additional ange Hood iring Diagrams (continued) Models: JXI8042, JXI8036, JXI8242, JXI8236 Electronic User Interface GND L N CON2 /G Electronic Power Board CON1 N L NL NM P1 P2 P4A P3 P4 LA P5 S4 P9 S3 S2 S1 P8 P7 P6 CON CON4 CON7 CON8 G B /G CON 6 N L CON CON 12 CON 5 N L CON 9 CON 10 G L B /G Installation Instructions E 36

41 Additional ange Hood iring Diagrams (continued) JX5030S, JX5036S Jenn-Air IING BOX L N Electronic User Interface CON2 - G -G Electronic Power Board CON1 TANSFOME CON3 N L NL NM P1 P2 P4A P3 P4 LA P5 S3 S2 S1 P8 P7 P CON4 S E C P I B B B G ATTENTION!: ADDITIONAL LAMPS ONL PESENT ON THE VESIONS ITH 4 LAMPS SEC PI TANSFOME B B - G - G G G 1 -G B Installation Instructions

42 Additional ange Hood iring Diagrams (continued) JX6030, JX6036 IING Jenn-Air DIAGAM MOTO SPEED 1 2 CONNECTIONS TO TEMINALS COLO TABLE B G G COLO TABLE ED -G SE1Q7A 3 -G -G G EL B BL -G BL B B -G Fan Speed Cont. Brd (FSCB) SPEED CONTACT Light Cont. Brd (LCB) B B FSCB B LCB B 12V 120V TANSFO- ME Installation Instructions

43 Additional ange Hood iring Diagrams (continued) JX8030, JX8036, JX8042 Jenn-Air IING DIAGAM Electronic User Interface BE1EA GND L N CON2 /G Electronic Power Board BE1CAA CON1 N L NL NM P1 P2 P4A P3 P4 LA P5 S4 P9 S3 S2 S1 P8 P7 P6 CON CON4 CON7 CON8 G B /G CON 6 N L CON CON 14 CON 5 G B /G N L N L CON 15 CON 16 M Installation Instructions

44 Additional ange Hood iring Diagrams (continued) JX8230, JX8236 Jenn-Air Electronic User Interface GND L N CON2 /G Electronic Power Board CON1 N L NL NM P1 P2 P4A P3 P4 LA P5 S4 P9 S3 S2 S1 P8 P7 P6 CON CON4 CON7 CON8 B /G 120V TANSTO- MATEU 12V G G B /G CON 6 CON 5 M Installation Instructions

45 Additional ange Hood iring Diagrams (continued) JX8836 Jenn-Air Electronic User Interface /G Electronic Power Board B B /G G /G G L N G B G G COLO TABLE /G COLO TABLE Installation Instructions

46 Additional ange Hood iring Diagrams (continued) JX9030S, JX9036S, JX9048S IING Jenn-Air DIAGAM Junction box N L Gnd I switch Switch Switch operation Position Connection Action ON 1 2 Light ON OFF No connection Light OFF -G I lamps B Closure temperature: 167 F±5.4 F (75+/-3 C) Opening temperature: 140 F (60 C) Temperature sensor uF G Fan speed Fan speed On Off Fan On Off Fan Off Light G B B B B Speed 1 Speed 2 Speed 3 25uF B B G -G G G /G Lamps Optional lamp used in 48" (121.9 cm) size hood Optional kit with 1 motor Blue-ed: 18 Motor esistance (Ohms) Blue-hite: 21.6 (min.) Blue-Black: 9.8 (max) Power supply: 120 VAC Motor Characteristics Power absorption: 420 Blue-Gray: 14.3 oom Temp: 73.4 F (23 C) Switch operation with button Position Connection Action Speed 1 Speed 2 Speed 3 3 Switch operation with button ON-OFF Position Connection Action 4 ON OFF Position Motor ON Frequency: 60 Hz Motor OFF Switch operation with button Light Connection Action OFF Current: 3.7A Lights Off Low Intensity High Intensity Installation Instructions

47 Additional ange Hood iring Diagrams (continued) KXI9736, KXI9748 KitchenAid Junction box N L Gnd G SE110A Fan speed Fan speed On Off Fan On Off Fan Off Light B Closure temperature: 167 F±5.4 F (75+/-3 C) Opening temperature: 140 F (60 C) Temperature sensor 25uF Speed 2 Speed 3 25uF Speed B B B B G /G G G B B G G -G Lamps Optional kit with 1 motor Motor esistance (Ohms) Motor Characteristics Blue-ed: 18 Blue-hite: 21.6 (min.) Blue-Black: 9.8 (max) Power supply: 120 VAC Power absorption: 420 Blue-Gray: 14.3 oom Temp: 73.4 F (23 C) Frequency: 60 Hz Current: 3.7A Switch operation with button Position Connection Action Speed 1 Speed 2 Speed 3 3 Switch operation with button ON-OFF Position Connection Action 4 ON OFF Position Motor ON Motor OFF Switch operation with button Light Connection Action OFF Lights Off Low Intensity High Intensity Installation Instructions

48 Additional ange Hood iring Diagrams (continued) KXU2830 IING KitchenAid DIAGAM SEL Motor Characteristics Power Supply Frequency 120 V 60 Hz Power Absorption 230 User Interface B B Main Board Speed 4 Speed 3 Speed 2 Speed 1 Lamp Neutral Neutral G L1 Neutral N L /G EMC Filter B B /G Primary Transformer Secondary Speed Motor esistance (Ohms) / 45.1 Min. / 37.7 /G 30.3 / 20.8 Max. M /G G /G G oom Temp F (23 C) 1 Installation Instructions

49 Additional ange Hood iring Diagrams (continued) KX2536, KX2530 KitchenAid Installation Instructions

50 Additional ange Hood iring Diagrams (continued) UXL6048SS, UXL6036SS KitchenAid iring Diagram Installation Instruction

51 Additional ange Hood iring Diagrams (continued) UXG7360VD, UVG73660VD KitchenAid iring Diagram Installation Instruction

52