R8 Exhaust Installation Guidelines
|
|
- Annabel Barrett
- 6 years ago
- Views:
Transcription
1 STāSIS Engineering R8 Exhaust Installation Guidelines
2 Exhaust Muffler support bracket bolt to muffler Muffler support bracket to chassis Muffler heat shield screws Heat shield bolt to chassis beneath anti roll bar Heat shield nut to chassis/vacuum pipe Speed clip to bumper bar and chassis for heat shield Heat shield bolt to bumper bar Heat shield bolt to chassis cross member Engine Air box to chassis Body Bumper cover center section outer bolts Bumper cover center section upper bolts Bumper cover center section lower bolts Lower air guide retaining screw Lower bumper to chassis bolt All bumper cover retaining bolts License plate mounting bracket Bumper bar bolts Lower air duct bolts Grille screws to taillight housings Grille screws to spoiler carrier Fender liner screws Reverse camera screws Outer heat shield bolts to bumper cover Taillight bolt to body Taillight nut to body Under tray bolts TORQUE VALUES 45 Nm 25 Nm 1.5 Nm 6 Nm 6 Nm 2 Nm 6 Nm 6 Nm 8 Nm 1 Nm 5 Nm 4 Nm 4 Nm 5 Nm 5 Nm 5 Nm 8 Nm 4 Nm 1.5 Nm 4 Nm 1 Nm 1 Nm 4.5 Nm 4.5 Nm 4.5Nm 4 Nm 2 of 22
3 R8 Exhaust Exhaust Kit Installation Application Guide Description R8 V8 Exhaust Assembly R8 V10 Exhaust Assembly Part Number SE811-E SE811-E Instructions 1 Using a T-30 torx driver, remove the 16 (per side) fender liner fasteners. Make sure to note the location of the short fastener along the fender arc and the stepped fastener at the rearward lower edge. 2 Using a T-30 torx driver, remove the 28 under tray and air duct fasteners. Make sure to note the location of the flanged fasteners holding on the air ducts, and the stepped fasteners on the rearward edge. 3 of 22
4 Remove the rear engine cover between the MAF sensors. Loosen all of the quarter turn fasteners on the left and right engine compartment side panels. Remove power steering reservoir cap. 3 Have a helper hold the engine cover open and disconnect the gas strut at the lower ball stud using a small flat blade screwdriver to release the clip (only do one side at a time). 4 of 22
5 4 Move the engine compartment side panel away from the body and disconnect plug for the courtesy lamp. Remove the engine compartment side panel and reattach gas strut to the ball stud. Install power steering reservoir cap to prevent contamination. Repeat on passenger side. 5 Disconnect the electrical connector on both MAF sensors. Using a flat blade, screwdriver or 7mm socket, loosen the throttle body boots at the MAF sensor on both sides. 5 of 22
6 6 Using a T-30 torx driver, remove the 4 screws holding the air box to the chassis (the 2 right side screws are shown in the picture). Slide back the corrugated plastic air inlet ducts on the sides of the air box and remove the air box from the vehicle. 6 of 22
7 Using the button on the center console, raise the rear spoiler fully. Using a T-20 torx, remove the 2 fasteners (one per side) securing the screens to the taillight housing. Using a T-30 torx, remove the 4 fasteners (two per side) securing the screens to the rear spoiler mounting plate. 7 Using a T-30 torx, remove the 3 stepped fasteners along the top edge of the panel and the 2 fasteners on the outer edge. 8 Using a T-30 torx, remove the 2 fasteners on the lower edge of the panel 7 of 22
8 Using a T-15 torx, remove the 2 fasteners securing the reverse camera (center in picture) Using a small flat blade screw driver, gently release the retaining tab for the two license plate lights. Disconnect the license plate light electrical connectors. Using a T-30 torx, remove the 2 fasteners on the lower edge of the panel that were covered by the license plate lights. 8 of 22
9 Gently remove the rear panel. Disconnect the electrical connector on the edge of the rear antenna. 9 of 22
10 Using a T-30 torx, remove the 2 stepped fasteners underneath the license plate. Using a T-30 torx, remove the 4 fasteners (two per side) securing the heat shields to the bumper cover. 10 of 22
11 Disconnect both rear side marker light electrical connectors. Disconnect the large electrical connector for the parking aid sensors on the bumper located behind the heat shield on the drivers side. Using a T-30 torx, remove the 4 stepped fasteners (two per side) securing the bumper to the quarter panel. 11 of 22
12 Using a T-30 torx remove the 4 fasteners (two per side) located underneath the taillights. Note: these bolts are encapsulated and will remain in the bumper. Using a T-30 torx, remove the 2 stepped fasteners on the underside of the bumper cover to chassis. Disconnect the ground and the two wiring harness connectors for the reverse camera. Have a helper hold the bumper. Using a T-30 torx, remove the 2 fasteners along the top edge of the bumper cover. Gently remove the bumper cover. 12 of 22
13 Using a T-30 torx, remove the 2 fasteners securing the muffler heat shield to the chassis brace. Bend the tab down to facilitate removal with muffler assembly Disconnect the rear spoiler electrical connector. Using a T-25 torx, remove the 2 fasteners securing the heat shields. 13 of 22
14 Using a T-30 torx, remove the 3 fasteners securing the heat shield to the bumper bar. Using a 13mm deep socket, remove the 2 speed nuts securing the lower heat shields to the chassis. Also remove the 2 speed nuts securing the heat shield to the bumper bar. Remove the heat shield from the vehicle. Using a 10mm triple square and a 13mm socket, remove the 4 bolts securing the bumper bar to 14 of 22
15 Remove the wiring from bumper bar. Remove the bumper bar from vehicle. Disconnect tail lamp wiring. Using a T-25 torx, remove the 4 fasteners (two per side) along the lower edge of the tail lamp. 15 of 22
16 Using a 10mm combination wrench, remove the 4 nuts (two per side) securing the tail lamp to the chassis. Remove tail lamp assemblies by pulling straight back. Disconnect the vacuum hose from the exhaust actuators. Using a 10mm socket, remove the 2 nuts (one per side) securing the heat shield and vacuum tube to the chassis. 16 of 22
17 Free heat shield from stud and vacuum pipe. Using a T-30 torx, remove the two bolts for the muffler heat shield to the chassis, just below the rear sway bar. Using a 13mm socket, remove the two speed nuts (one per side) securing the heat shield to the chassis. This is just underneath the rear taillight area. 17 of 22
18 Using a 16mm wrench, remove the two bolts, washers and spacers securing the muffler to the lower hangers. Using a 13mm wrench, remove the 4 fasteners and spacers (2 per side) securing the upper exhaust hangers to the chassis. Using a female T-10, loosen the fasteners on the V- Band exhaust clamps. 18 of 22
19 Remove the V-Band exhaust clamp Remove the muffler and heat shield assembly from the vehicle, being careful not to damage the heat shield. Using a 16mm wrench, remove the two bolts securing the upper muffler hangers to the muffler. 19 of 22
20 Remove the 2 E clips and springs/washers that centralize the heat shield on the muffler. Using a T-25, remove the 18 fasteners securing the forward heat shield on the exhaust. Remove the forward portion of the muffler heat shield. 20 of 22
21 Slide the muffler assembly to one side to facilitate removal of the rearward heat shield. Remove the O.E. exhaust and replace with the new exhaust. Reassemble the heat shield, centralizing springs and hangers in the reverse order of disassembly. 21 of 22
22 Remove short section of rubber hose from the vacuum pipe that goes to the exhaust actuators. Install the 2 supplied vacuum caps onto hard lines. Continue with the remaining installation and reassembly in the reverse of disassembly. 22 of 22
TESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More information3/8 Universal Joint Phillips Head Screwdriver
Magnetic retrieval tool Pliers 1/4 Ratchet Drive T-35 Torx Socket 3/8 Ratchet Drive 5mm Allen Head Socket Torque Wrench 7-3/8 Drive Extension Flat Head Screwdriver 10mm Socket 8mm Socket 3/8 Universal
More informationREVi RX-8 Intake. RX-8 REVi Intake System I PN Installation Instructions. Tools Required:
RX-8 REVi Intake System PN 18299 Installation Instructions I-18299 Tools Required: Small/Stubby Phillips head screwdriver Small flat head screwdriver Medium Phillips head screwdriver 10mm socket and ratchet
More informationPage 1 of 7 Bumpers - Front Bumper Cover Removal and Installation Removal 1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and
More informationFront Bumper Fascia Replacement
Page 1 of 10 2008 Pontiac G8 G8 Service Manual Body Repair Bumpers and Fascias Repair Instructions Document ID: 2044380 Front Bumper Fascia Replacement Removal Procedure Caution: Refer to Safety Glasses
More informationInstallation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD
Installation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always recommend
More informationSTaSIS Engineering B6 B7 Streetsport Suspension
STaSIS Engineering B6 B7 Streetsport Suspension SS Suspension Kit Parts List Qty Description Part Number 1 STaSIS adjusted Koni cadmium plated dampers (2 front, 2 rear) 1150-5061 Special Tools Required
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER 2018 FORD F150
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 28 12mm x 37mm x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 4 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 12
More informationInstallation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo
Installation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always
More informationPlease take time to read and understand these installation instructions.
Cat Back Exhaust System 2013+ SRT/ GTS Viper Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service
More informationFactory safe air/fuel ratio s for Optimum performance Patent# 7,359,795
Part Number SP1125 2007-09 BMW 335i 2008-09 BMW135i 3.0L Twin Turbo L6 This kit is equipped with the Injen/AMSOIL Ea nanofiber dry filters, Ea nanofiber filters do not require oil. 1-2 piece air intake
More informationNissan R35 GTR Intercooler Pipe Kit w/ Cold Air Intake Installation Instructions
Nissan R35 GTR Intercooler Pipe Kit w/ Cold Air Intake Installation Instructions 1. Disconnect the negative terminal on the battery that is located at the passenger firewall side. 2. Remove both front
More informationRIM Hood For Aeromaster Bodies
RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationIE Audi B9 S4, S5, A4, A5, Allroad FDS Intercooler Install Guide IETPCK1
IE Audi B9 S4, S5, A4, A5, Allroad FDS Intercooler Install Guide IETPCK1 Thank you for purchasing the best performing intercooler on the market! This instruction guide is used for installation of IE s
More informationM-9603-FST FOCUS ST COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS
M-9603-FST Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More informationInstallation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo
Installation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. 1. 4. 5. At this type of installation
More informationFitting Instructions. Revo MQB Golf/GTi/Octavia/Leon Intercooler. Recommended Tools. Contents RV581M Dealer installation advised.
RV581M100100 Recommended Tools Contents No. Description Tools Size Intercooler Torx Bit T25, T30 Bracket Kit llen Key 4, 5 mm Silicone Hoses Socket 7, 10, 16, 19 mm Hose Clamps Flat Head Screwdriver Small,
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Performance We ask that you take a few moments to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationHIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D , D A
HIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D760-0320, D760-0320A 1992-95 325i, is 1995 M3 (3.0L) Parts List: 1 Intake Tube 1 Silicone Hose 1 Air Flow Meter Bracket 1 Hose Clamp (#36z) 1
More informationHeadlamp Assembly. Headlamp Bulb Low Beam H4. Headlamp Bulb High Beam H7 REMOVAL AND INSTALLATION Exterior Lighting
417-01-52 Exterior Lighting 417-01-52 REMOVAL AND INSTALLATION Headlamp Assembly 3. Remove the rubber boot from the lamp back face. WARNING: Bulbs become hot to touch and can cause burns if not allowed
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationInstallation Instructions :BMW B58 : Page 1
Installation Instructions :BMW B58 : Page 1 1. We will start by removing the stock airbox system. Loosen the hose clamp around the airbox. Remove the MAF sensor plug the white clip unlocks by pulling it
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located
More informationB8 2.0T Exhaust Installation Guidelines
STāSIS Engineering B8 2.0T Exhaust Installation Guidelines B8 2.0T Exhaust Exhaust Kit Installation Application Table Description B8 A4 2.0TFSI Exhaust Assembly (Manual and 8-speed Tiptronic) B8 A5 2.0TFSI
More informationPart Number SP BMW 335i BMW135i 3.0L Twin Turbo L6
This kit is equipped with the Injen/AMSOIL Ea nanofiber dry filters, Ea nanofiber filters do not require oil. Part Number SP1125 2007-09 BMW 335i 2008-09 BMW 3.0L Twin Turbo L6 1-2 piece air intake system
More informationR O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP
R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer
More informationInstallation Instructions Camaro ZL1 ( Z) ( ZB)
Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1
More informationMustang 5.0L Cold Air Intake Installation Instructions P/N:
2015-2017 Mustang 5.0L Cold Air Intake Installation Instructions P/N: 421826 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015-2017 Mustang 5.0L Cold Air Intake Installation Instructions P/N:
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: ¾, 7/8, 15/16 Drill Bits: 1/8, 9/16, 5/8 1-1/8 HOLE SAW Other Tools: Center Punch, Measuring Tape Installation Instructions 5 WARNING: Under no circumstances
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationExhaust System Installation Turbo Downpipe Audi MKII TT-RS 2.5T CD100028
Please take the time to read and understand installation instructions. APR recommends that installation of this system be performed by a qualified service center or professional muffler installer who has
More informationInstallation Instructions
Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor
More information2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More information03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationHAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
9/23/2009 1 of 6 ITEM 1 QTY 8 Parts List PART NUMBER DESCRIPTION 3/8" CONICAL TOOTHED WASHER TOOLS REQUIRED #2 PHILLIPS SCREWDRIVER #2 STUBBY SCREWDRIVER 8mm SOCKET 13mm SOCKET RATCHET 12" EXTENSION TORQUE
More informationFRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # & P INSTALATION INSTRUCTIONS
FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # 48.10.90 & 48.10.90P INSTALATION INSTRUCTIONS PART LIST: 1 INTERCOOLER CORE 1 U-BENT TUBE 1 L-SHAPED TUBE 1 INTERCOOLER INLET TUBE 4 M6 NYLOC NUT 3 M6
More informationThank you for purchasing the AWE SwitchPath Exhaust System for the Audi B9 S5 Sportback.
Thank you for purchasing the AWE SwitchPath Exhaust System for the 2017+ Audi B9 S5 Sportback. Let s go! Switchpath Exhaust Parts: 1 Driver downpipe upper section (part A10) 1 Driver downpipe lower section
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System: Slip-On for the Laborghini Gallardo 550-2 Coupe Laborghini Gallardo 560-4 Coupe / Spyder Laborghini Gallardo 570-4 Coupe / Spyder Congratulations on
More informationAPR, LLC
+ 1. 3 3 4. 5 0 2. 5 1 8 1 4 8 0 0 U S H W Y 2 8 0 W e s t, O p e l i k a, A l a b a m a 3 6 8 0 1 4 8 0 0 U S H W Y 2 8 0 W e s t, O p e l i k a, A l a b a m a 3 6 8 0 1 + 1. 3 3 4. 5 0 2. 5 1 8 1 NOTES:
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: F10 M5 # D Fits: F06/F12/F13 M6 PARTS LIST
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0035 Fits: 2013-15 F10 M5 # D760-0037 Fits: 2012-15 F06/F12/F13 M6 PARTS LIST (1) Left Carbon Airbox Lid (1) Right Carbon Airbox Lid (1) Left Carbon Snorkel
More information99-04 GT. Hellion Power Systems Mustang GT Kit Instructions
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationR8 V10 Coupe and Spyder Supercharger Installation Guidelines
STāSIS Engineering R8 V10 Coupe and Spyder Supercharger Installation Guidelines R8 TORQUE VALUES Body Bumper cover center section outer bolts Bumper cover center section upper bolts Bumper cover center
More informationPARTS LIST: HEAVY DUTY FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: HEAVY DUTY FRONT BUMPER 1 Heavy Duty Bumper Assembly 18 12-1.75mm x 50mm Hex Bolts 1 Driver/Left Frame Mounting Bracket 36 12mm x 32mm x 3mm Flat Washers 1 Passenger/Right Frame Mounting Bracket
More informationSCION tc STRUT TIE BAR Preparation
SCION tc 2005 - STRUT TIE BAR Preparation Part Number: 00016-80440 Code: YY1 Kit Contents 1 1 DS Mount Plate 2 1 PS Mount Plate 3 1 Cross Bar 4 1 Hardware Bag Hardware Bag Contents 1 4 8mm Screws 2 4 8mm
More informationR O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP
R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer
More informationFog Lamp Instructions
Fog Lamp Instructions 2011+ Ford Super Duty Congratulations on your purchase of a high quality PUTCO product. Should you need any application or technical assistance feel free to call us at: 1-800-247-3974
More informationPart number SP Acura RSX 4 Cyl.
Part number SP1470 2002-06 Acura RSX 4 Cyl. 1- One piece cold air intake 1-3 Dyno-Tuned Filter (#1017) 1-2 3/4 90 deg. elbow (#3060) w/ 1525 grommet 1-20 8mm vacuum hose (#3091) 1-18 17mm vacuum hose (#3080)
More informationA6 Suspension, Touring
A6 Suspension, Touring Suspension Kit Parts List Qty Description 1 Stasis Performance Spring Kit Special Tools Required Qty Description Part Number 1 Torque Wrench VAG 1331 1 Torque Wrench VAG 1332 1 Engine/transmission
More informationMAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS
MAZDA BT-50 (October 0 Production Onwards) & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Installation Time: Approx. 0 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent
More informationHD BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST:
PARTS LIST: 1 HD Bull Nose Bumper Assembly 1 Bumper Cover 1 Winch Tray Bracket Assembly 5 6mm Combo Button Head Bolts (cover) 2 3-hole Bracket Spacer Plates 1 Wrench (6mm Button Head) 2 Plastic Plugs for
More information(2) License Plate Plugs
PARTS LIST: 1 HD Bull Nose Bumper Assembly 12 12-1.75mm x 50mm 1 Driver/left Frame Mounting Bracket 40 12mm x 37mm OD x 3mm Flat Washers 1 Passenger/right Frame Mounting Bracket 20 12mm Lock Washers 1
More informationGMC Yukon
Torch Series LED Grille TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More information**** Upper Filler Panel must be painted before installation. ****
05 06 Ford GT Sweet Ass Bumper Delete Kit CDC # 0512-7000-01 Please read instructions thoroughly before installing. About the Product: The Sweet Ass Bumper Delete Kit is designed and manufactured exclusively
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,
More informationTools Required. Metric Wrench Set Screwdriver Set Metric Socket Set Pliers Heavy duty hydraulic Jack and Car Stands Box knife or similar Hacksaw WD40
Subaru 2004+ Legacy GT & Outback XT For JDM 2.0 twinscroll turbo and USDM 2.5 turbo models Front Mount Intercooler Fitting Instructions PN# LEG-1348-000 You are now the proud owner of a highly tested and
More informationIntake Installation Instructions P/N 9046 (red filter) - P/N 9046B (blue filter) P/N 9046K (black filter)
Intake Installation Instructions P/N 9046 (red filter) - P/N 9046B (blue filter) P/N 9046K (black filter) Year/Make/Model/Engine 2012-17 Ford Focus 2.0L Parts List 1- Intake tube 1- Heat shield, Side 1-
More informationChevrolet ZL1 Camaro Lingenfelter Air Intake Kit Installation Instructions (LSA engine)
2012-2013 Chevrolet ZL1 Camaro Lingenfelter Air Intake Kit Installation Instructions (LSA engine) PN: L650182012 Revision - 1.6 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733
More informationROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8
Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128
More information2018 Mustang 5.0L Cold Air Intake Installation Instructions P/N: ( )
Installation Instructions P/N: 422086 (131850-9600) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2018 Mustang 5.0L Cold Air Intake Installation Instructions P/N: 422086 (131850-9600) Application:
More informationPARTS LIST: ELEVATION BULL NOSE FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: 1 Elevation Bumper Assembly 2 8-1.25mm x 25mm Hex Bolts 1 Winch Tray Bracket Assembly 2 8-1.25mm x 16mm Hex Bolts 2 3-hole Bracket Spacer Plates 6 8mm x 24mm x 2mm Flat Washers 2 Plastic Plugs
More informationBRZ/FR-S 3.00 Cold Air Intake
BRZ/FR-S 3.00 Cold Air Intake Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket performance
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationC&L Cold Air Intake (03-04 Mach 1) - Installation Instructions
C&L Cold Air Intake (03-04 Mach 1) - Installation Instructions The below installation instructions work for the following products: C&L Cold Air Intake (03-04 Mach 1) Please read through the instructions
More informationINSTALLATION INSTRUCTIONS
11485 YEARS: 2015-CURRENT Safety glasses should be worn at all times while installing this product. INSTALLATION INSTRUCTIONS MODEL: C300 MAKE: MERCEDES STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE
More informationFENDER ELIMINATOR. Remove axle nut, slide out axle, and drop rear tire away from the fender. (Picture 1)
TRIUMPH BOBBER Remove axle nut, slide out axle, and drop rear tire away from the fender. (Picture ) Remove () tail light bolts. (Picture ) Unplug stock connectors and remove from underneath the fender.
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationDo not have any open flame or heat sources close to the installation
March 6, 2017 IS# 791 Page 1 of 16 Thank you for purchasing a Transfer Flow, Inc. 50-gallon replacement fuel system for your 2011-16 Ford diesel short bed pickup. This system will fit any 2x4 or 4x4 crew
More informationProduct: Variable Height Spring. Part Numbers: N. Applications: BMW F8x, M2/M3/M
Product: Variable Height Spring Part Numbers: 415-503001-N Applications: BMW F8x, M2/M3/M4 2014-17 Contents in the box: Qty Part # Description 1 00P-0A1646-B Front Passenger Sleeve Assembly 1 00P-0A1645-N
More informationBMS F1X M5/M6 S63TU Stage1 Install Guide
BMS F1X M5/M6 S63TU Stage1 Install Guide Last updated 10/22/2018 Use subject to terms and conditions posted at http://www.burgertuning.com/terms.htm THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING
More informationF L Ecoboost V F L Ecoboost V6 Performance Pac Level 2 Installation Instructions P/N: (1115TT-PWRPK2)
2015-2016 F-150 3.5L Ecoboost V6 2015-2017 F-150 2.7L Ecoboost V6 Performance Pac Level 2 Installation Instructions P/N: 422007 (1115TT-PWRPK2) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015-2016
More informationFULL LENGTH HEADERS/ CATTED HEAD PIPES
INSTALLATION INSTRUCTIONS INS232 2016-2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder
More informationINSTALLATION INSTRUCTIONS PART NUMBER:21-729
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-729 2010-2013 MAZDA MX-5 MIATA 2.0L I-4 PARTS LIST Description Qty. Part Number A Tube, Lower Intake, 2006-13
More informationTENF8046MCD F8X M3/M4 TEST PIPES (REMOVES SECONDARY CATS) **NOT FOR USE ON ROAD VEHICLES / FOR OFF-ROAD AND RACING USE ONLY**
Turner Motorsport LLC / 1-800-280-6966 / www.turnermotorsport.com DI/DBM 3/21/16 TENF8046MCD F8X M3/M4 TEST PIPES (REMOVES SECONDARY CATS) **NOT FOR USE ON ROAD VEHICLES / FOR OFF-ROAD AND RACING USE ONLY**
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust STOP Please take time to read and understand
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More information(Ford Transit Rear Bumper) INSTALLATION INSTRUCTIONS
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 (Ford Transit Rear Bumper) INSTALLATION INSTRUCTIONS Please read before beginning Stainless steel hardware may bind together
More information1. Front Fascia Removal 1.1 Remove the 6 plastic clips that secure the upper valance, then remove. 1.2 Remove 6 upper bolts that hold the grille and f
STRUT 2015 GMC Denali Collection Installation Manual " 1. Front Fascia Removal 1.1 Remove the 6 plastic clips that secure the upper valance, then remove. 1.2 Remove 6 upper bolts that hold the grille and
More information1 M-3000-H4 F150 4X4 Lowering Kit
READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.
More informationMTF Power Package Warranty Guidelines & Installation Instructions
STāSIS Engineering MTF Power Package Warranty Guidelines & Installation Instructions STaSIS MTF Power Package Warranty Checklist Congratulations on your purchase of the STaSIS Engineering MTF Power Package
More informationTOYOTA RAV FOG LIGHT KIT Preparation
Preparation Part Number: PT413-42163 Kit Contents Item # Quantity Reqd. Description 1 7 7 Wire Tie 2 4 #10-16 Cross Pan-Washer Head Screws 3 1 Switch 4 1 Relay 5 1 LH Fog Light Bezel 6 1 RH Fog Light Bezel
More informationShort-throw Shifter Installation Guide
Short-throw Shifter Installation Guide Removal Procedure 1) Remove the shift control knob. A. Lift up on the rear portion of the shift control closeout boot retaining ring and detach the retaining ring
More informationLingenfelter Signature Series Camaro SS Rear Valance
Lingenfelter Signature Series 2010-2012 Camaro SS Rear Valance PN: L850161410 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-0422 fax www.lingenfelter.com
More informationChevrolet Cobalt Short Shifter Installation Manual
Chevrolet Cobalt Short Shifter Installation Manual Pull shift boot down on the shifter shaft. Pull up on the shift knob to remove it. It requires some force. Remove the ebrake console, shifter console
More informationPart number SP Mitsubishi Lancer 4 cyl. 2.0L non-turbo. 1- Three piece cold air intake
Part number SP1835 08-09 Mitsubishi Lancer 4 cyl. 2.0L non-turbo 1- Three piece cold air intake 1- Formed silicone hose (#3158) 1-2 1/2 Injen filter (#1012) 1-2 3/4 straight hose (#3043) 4- Power-Bands.312.040
More informationINSTALLATION INSTRUCTIONS LD-1 REAR BUMPER RAM 1500 PART#R R #PW017838
INSTALLATION INSTRUCTIONS LD-1 REAR BUMPER PART#R102617 R102620 #PW017838 PARTS LIST: 1 LD1 Bumper Assembly 4 12-1.75mm x 40mm Hex Bolts 1 Push in License Plate Light 4 12mm x 37mm x 3mm Flat Washers 2
More information#TL B8 A4/Q5 DOWNPIPE/ INSTALLATION INSTRUCTIONS
#TL100085 B8 A4/Q5 DOWNPIPE/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification Audi A4, but other models, like the allroad, A5, and Q5 are similar. When
More informationFord Racing SVT Performance Cooling Fan (05-14 GT, GT500)
Ford Racing SVT Performance Cooling Fan (05-14 GT, GT500) Time Necessary: Approximately 60-90 minutes Tools Required: 8mm wrench 8mm socket (3/8 drive, optional) 10mm socket (3/8 drive) 10mm deep socket
More information54531/ FORD FUSION
54531/51531 54531/51531 13-15 FORD FUSION 13-15 FORD FUSION FORD FUSION Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill
More informationInstallation instructions, accessories. Body kit
Installation instructions, accessories Instruction No 31265373 Version 1.1 5 Part. No. Body kit IMG-256263 Volvo Car Corporation Body kit - 31265373 - V1.1 Page 1 / 42 Equipment A0000162 A0000163 IMG-239664
More information