Emergency lighting units EM series. EM BASIC, V BASIC version

Transcription

1 T T TCDE TCSE TCTE TC TCDD EM, 0 0 V version roduct description Emergency lighting supply unit for manual testing For linear and compact fluorescent lamps Small dimensions ( x mm crosssection) roperties or h rated duration Compatible with all electronic ballasts (dimmable and nondimmable) Can also be used in combination with conventional magnetic ballasts pole technology: pole lamp changeover and delayed power switching for the ballast AC output voltage optimised for TCDD and TC lamps DC output voltage optimised for T fluorescent lamps Cathode heating adapted for compact lamps itchover relay with highcurrent contacts IDC (insulation displacement connection) Green charge status display ED Checking the emergency lighting function by interrupting the unswitched phase ptional test switch Deep discharge protection connection, shortcircuit protected (not reversible) olarity reversal protection for battery Batteries Hightemperature cells icd batteries D cells Blade terminals for simple connection È Standards, page Wiring diagrams and installation examples, page Technical data Rated supply voltage 0 0 V Voltage tolerance for performance (0/%) 0 V Voltage tolerance for safety (±0%) 0 V Mains frequency 0 / 0 Hz Mains current 0.0 A Rated power W charging time h Discharge current h. A Discharge current h. A Charge current 0 ma eakage current (E) 0. ma Ambient temperature ta C Max. casing temperature tc C Mains voltage changeover threshold according to E 0 Min. lamp starting temperature (emergency operation) 0 C of protection I0 rotection class I rdering data umber of cells Article number Rated operating time h EM A EM B EM C EM A EM B EM A EM B EM C 0000 ackaging: pieces/carton, 0 pieces/pallet EM B also available in 0 V AC version Data sheet /

2 rdering data umber of cells Article number EM D EM A Rated operating time h EM B EM E EM B ackaging: pieces/carton, 0 pieces/pallet ACCES SRIES Test switch EM roduct description For connection to the emergency lighting unit For checking the device function rdering data Article number Test switch EM 0 ackaging: pieces/bag, 00 pieces/carton ACCES SRIES Status indication green ED roduct description A green ED indicates that charging current is flowing into the battery rdering data Article number ED EM green 0 ED EM green, ultra high brightness ackaging: pieces/bag, 00 pieces/carton Data sheet /

3 EM for linear lamps, h h cells cells EM B EM E EM B Article no. amp type Wattage BF in emergency lighting mode in % for rated operating time T W W W 0 Technology and capacity icd Ah Dcells Design umber of cells Article number Assignable batteries Stick AccuiCd A 0 Side by side AccuiCd B Stick AccuiCd A 000 Side by side AccuiCd B Stick Stick AccuiCd C ote: 0 C batteries also available (see seperate datasheet at For extended application of the lamp please see E 00en_EM _Extended Application_V.pdf at Data sheet /

4 EM for linear and compact lamps, h h cells cells cells cells EM A EM B EM C EM A EM B EM A EM B EM C EM D EM A Article no Technology and capacity icd Ah Dcells Design umber of cells amp type Wattage BF in emergency lighting mode in % for rated operating time T W 0 W 0 W 0 W 0 W W. W W T W 0 0 W W 0 0 W 0 W TCDD 0 W 0 W W 0 0 W W W TCSE W 0 W W W TCDE 0 W W W W TCTE W 0 W W W W TC W W 0 W W 0 0 W 0 W Article number Assignable batteries Stick AccuiCd A 0 Side by side AccuiCd B Stick AccuiCd A 000 Side by side AccuiCd B Stick Stick AccuiCd C Stick AccuiCd A Stick Stick AccuiCd C 0000 Stick Stick AccuiCd C ote: For more lamp combinations for and h see separate data sheet. ot for use with compact amalgam lamps. 0 C batteries also available (see seperate datasheet at For hour operation only. Used only in maintained mode because mercury migration may occur during emergency operation. amp restrictions apply, for further information contact Tridonic. For extended application of the EM B Basic please see E 00en_EM _Extended Application_V.pdf at Data sheet /

5 EM Extended Application The EM range consists of different product types (A, B, C, D). These are needed due to the different starting and operating requirements of the various types of fluorescent lamps. Each EM type is optimised to give best possible lamp performance and life performance with the minimum number of battery cells. Additional to this there is also the possibility to use only one type out of the EM range to operate most lamp types of a rated duration the EM B for hours and the EM E for hour. According to the statement above please note that by using only one EM type for the complete lamp range, some lamps will be run outside of the specification. This will lead to a decrease in the lamp performance. In the following table an information about the effect on the duration and the BF for all lamps which can be operated is listed. Ballast umen Factor (BF) and duration amp T T TCDE TCD/TE TCTE TCSE TC TCDD T circline W W W W W W W W W W W W W W W 0 W W W W W W W W W W W W W 0 W W 0 W W W W 0 W EM B Duration hours.... BF % EM E Duration hours BF % Data sheet /

6 Standards according to E 0 according to E 0 E 0 E 0 E 0 E 000 E 000 E E 00 E 00 E 000 Isolation and electric strength testing of luminaires Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production. According to IEC 0 Annex Q (informative only!) or EEC 0Annex A, each luminaire should be submitted to an isolation test with 00 VDC for second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal. The isolation resistance must be at least MΩ. As an alternative, IEC 0 Annex Q describes a test of the electrical strength with,00 VAC (or, x,00 VDC). To avoid damage to the electronic devices this test must not be conducted. Mechanical details Channel manufactured from 0. mm Galvatite galvanised steel. Cover manufactured from 0. mm white precoated steel. ED charge indicator Green Mounting hole. mm diametre ength of ED lead 0 mm (Bezel supplied fitted to ED) Insulation temperature rating: 0 C Test switch Mounting hole mm diametre ength of test switch lead 0 mm leads Quantity: red and black ength: 000 mm (Accu icd B, B, C), 00 mm (all others) Wire type: 0. mm solid conductor Insulation temperature rating: 0 C Termination ush on. mm receptacle to suit battery spade fitted with insulating cover Termination mm stripped insulation Batteries case temperature range 0 C to C to ensure years design life battery voltage/cell. V capacity. / Ah max. short term temperature (reduced lifetime) 0 C Connection method:. x 0. mm spade welded to end of cell For the stick batteries this connection is accessible after the battery end caps have been fitted. To inhibit inverter operation, only dis connect the batteries by removing the connector from the battery spade tags. Electrical connections An earthed starting aid is recommended. The module should be earthed by the fixings used to attach it to the luminaire. Terminal block type: ush wire and insulation displacement Terminal block capacity ush wire: 0. to. mm solid conductor Insulation displacement: 0. mm solid conductor Wire strip length:. to. mm amp lead length:,00 mm max. The longer pair of leads should always be connected to terminals and. CE marking The modules are CE marked for compliance with the low voltage directive. Certificates of compliance are available to allow luminaires to be CE marked for compliance with the EMC directive. Twopiece batteries are supplied with a 00 mm lead with. mm receptacles at each end and insulating covers to connect the separate sticks together. Wiring guidelines To ensure that a luminaire containing high frequency emergency units complies with E 0 for radio frequency conducted interference in both normal and emergency mode it is essential to follow good practice in the wiring layout. Within the luminaire the switched and unswitched 0 Hz supply wiring must be routed as short as possible and be kept as far away as possible from the lamp leads. This means, for example, in a linear T or T luminaire the mains wiring should be routed along one side of the luminaire body, while the wires to the emergency lamp from the emergency module are routed along the other side. The high frequency emergency lamp wiring contains hot leads at pins and, which have high voltage to earth. These should be kept as short as possible and separated from other wiring to minimize coupling. They also have a restriction on capacitance to other wiring and earth of 00 pf, which must be observed to ensure good lamp starting. With an earth connection of the metal case of the emergency module the noise suppression can be further improved. The wiring of the earth should be kept as short as possible. Through wiring may affect the emc performance of the luminaire. With the use of the fifth pole possible compatibility problems between the products can be prevented. Depending on the luminaire wiring the radio suppres sion in the emergency mode of operation can be further improved. Capacitive loading limits of lamp leads must not be exceeded. ote the capacitance of the emergency lamp leads adds to the capacitance of the leads from the ballast to the EM module when considering ballast loading. Service life Average service life 0,000 hours under rated conditions with a failure rate less than 0 %. Average failure rate of 0. % per,000 operating hours Data sheet /

7 Circuit diagrams Batt ve Unitched ine range () ED ink () Batt ve ptional Test itch in EM * hot leads itched ine in Batt ve Unitched ine range () ED ink () Batt ve FC ptional Test itch EM S * hot leads series capacitor circuit or on maintained Single lamp switch start circuit with conventional control gear itched ine in Batt ve Unitched ine range () ED ink () Batt ve FC ptional Test itch EM S S * hot leads itched ine Batt ve Unitched ine range () ED ink () Batt ve ptional Test itch in EM series capacitor circuit or amp EECTRIC BAAST Twin series switch start circuit with conventional control gear Single lamp high frequency electronic ballast itched ine Batt ve Unitched ine range () ED ink () Batt ve ptional Test itch in EM Emergency amp itched ine Batt ve Unitched ine range () ED ink () Batt ve ptional Test itch in EM Emergency amp EECTRIC BAAST EECTRIC BAAST amp amp Twin lamp high frequency electronic ballast ( lamp lead connections) Twin lamp high frequency electronic ballast ( lamp lead connections) itched ine Batt ve Unitched ine range () ED ink () Batt ve ptional Test itch in EM Emergency amp acking quantities: EM : pieces/carton Test itch: pieces/bag 0 cartons/pallet 00 pieces/carton 0 pieces/pallet EECTRIC BAAST Accu icd: amp ED green: pieces/carton pieces/bag Twin lamp high frequency electronic ballast ( lamp lead connections) 00 pieces/carton Data sheet /