OEM Emergency Portfolio. Product Guide. Emergency components for LED, fluorescent and auxiliary purpose

Transcription

1 OEM Emergency Portfolio Product Guide Emergency components for LED, fluorescent and auxiliary purpose

2 Contents Introduction to this guide 3 LED Modules 4 PHL-EL3 PHL-EL3-80 PHL-EL3-D PHL-EL3-D80 PHL-EL3-4 PHL-EL3-S3W PHL-EL3-3W Fluorescent Modules 9 PHF-EL3-L6 PHF-EL3-3 PHF-EL3-4 PHF-EL3-5 PHF-EL3-6 PHF-EL3-3/14 PHF-EL3-4/14-24 PHF-EL3-6/35-49 PHF-EL3-6/28-54 PHF-EL3-6/55 Batteries 13 PHB-EL3-C3-S PHB-EL3-C3-FL PHB-EL3-C4-S PHB-EL3-C5-S PHB-EL3-C6-TS PHB-EL3-M3-S PHB-EL3-M3-T PHB-EL3-M4-TS PHB-EL3-M5-TS PHB-EL3-M6-TS LED Auxilary, LED Indicators and Accessories 14 PHI-EL3-24 PHI-EL3-30P PHI-EL3-LI PHI-EL3-L1D PHI-EL3-SR Range Overview 16 Lamp Compatibility Chart 17 2

3 Introduction to this guide The Philips OEM Emergency Portfolio offers a wide range of emergency lighting conversion components, required for the manufacture of emergency luminaires. The range supports the installation of emergency lighting schemes which comply with current regulations. Thank you for choosing the Philips OEM Emergency Portfolio. In this guide you will find the specification information for the portfolio. For installation information please refer to the Installation Guide. As technology is continuously improving, we advise you to visit our website: for the latest details. The Philips OEM Emergency Portfolio is the ideal choice for emergency lighting needs in a broad range of new construction and retrofit applications within the commercial sector, including offices, warehouses, schools, hospitals, public buildings, industrial and retail applications. 3

4 LED Components PHL-EL3 & PHL-EL Hour EM Converter for 6-55V and 6-80V LED Loads The Emergency PHL-EL3 & PHL- EL3-80 are 3 hour emergency lighting converters designed to suit a wide range of LED types and circuits. The converter automatically adjust the output LED current to provide the best match between the battery and the load, providing maximum illumination whilst ensuring battery duration. PHL-EL3 for 2-20 LEDs in series (6-55V) PHL-EL3-80 for 2-30 LEDs in series (6-80V) Additional 3rd pole relay Deep discharge protection Compact enclosure Constant current charger Technical Details PHL-EL3 PHL-EL NC Voltage Range 6-55 Volts 6-80 Volts LED Current Limit 320mA 320mA Battery Current Limit 1100mA 1100mA Mains Supply Voltage V AC V AC Mains Power 5 Watts 5 Watts Mains Frequency 50/60Hz 50/60Hz Power Factor Charge Current 200mA 200mA Recharge Time 24-Hours 24-Hours Module Dimensions 165mm x 45mm x 29mm 165mm x 45m x 29mm Module Weight 285g 285g The units are suitable for use with the following Philips Emergency Batteries: PHB-EL3-C3-S 3.6V 4Ah NiCd BATTERY IN STICK FORMATION PHB-EL3-C3-FL 3.6V 4Ah NiCd BATTERY IN FLEXIBLE FORMATION PHB-EL3-M3-S 3.6V 4Ah NiMH BATTERY IN STICK FORMATION PHB-EL3-M3-T 3.6V 4Ah NiMH BATTERY IN TRIANGULAR FORMATION 4

5 LED Components PHL-EL3-D & PHL-EL3-D80 3 Hour EM DALI Converter for 6-55V and 6-80V LED Loads A 3Hr emergency lighting converter with DALI interface and automatic test function, designed to suit an extremely wide range of LED types and circuits. The DALI converter automatically adjusts the output LED current to provide the best match between the battery and the load, providing maximum illumination whilst ensuring full battery duration. PHL-EL3-D for 2-20 LEDs in series (6-55V) PHL-EL3-D80 for 2-30 LEDs in series (6-80V) 2-pole changeover relay Additional 3rd pole relay Deep discharge protection Compact enclosure Constant current charger Technical Details PHL-EL3-D PHL-EL3-D80 12NC Voltage Range 6-55V 6-80V LED Current Limit 320mA 320mA Battery Current Limit 1100mA 1100mA Mains Supply Voltage V AC V AC Mains Power 5W 5W Mains Frequency 50/60Hz 50/60Hz Power Factor Charge Current 200mA Nominal 200mA Nominal Recharge Time 24-Hours 24-Hours Module Dimensions 165mm x 45mm x 29mm 165mm x 45mm x 29mm Module Weight 300g 300g The units are suitable for use with the following Philips Emergency Batteries: PHB-EL3-C3-S 3.6V 4Ah NiCd BATTERY IN STICK FORMATION PHB-EL3-C3-FL 3.6V 4Ah NiCd BATTERY IN FLEXIBLE FORMATION 5

6 LED Components PHL-EL3-4 3 Hour EM Converter for V LED Loads The PHL-EL3-4 is a 3 hour emergency lighting conversion module designed to power suitable mains lamps (e.g. some GU10 & T8 LED tubes) and high voltage LED boards (50-250V DC) - check with the Philips technical team for compatibility. The PHL-EL3-4 automatically adjusts the output LED current to provide the best match between the battery and the load, providing maximum illumination whilst ensuring full battery duration. 2-pole changeover relay Additional 3rd pole relay Deep discharge protection Compact enclosure Constant current charger Technical Details PHL-EL3-4 12NC Mains supply Voltage Battery Current Limit Mains Power Mains Frequency Power Factor Charge Current Recharge Period Dimensions Module weight v AC 1100mA 5 Watts 50/60Hz mA Nominal 24 Hours 165mm x 45mm x 29mm 296g The units are suitable for use with the following Philips Emergency Batteries: PHB-EL3-C4-S 4.8V 4Ah NiCd BATTERY IN STICK FORMATION PHB-EL3-M4-TS 4.8V NiMH BATTERY IN TWIN STICK FORMATION 6

7 LED Components PHL-EL3-S3W 3 hour maintained driver for single 700mA LED with strain relief The PHL-EL3-S3W is a complete quick & easy solution for LED mains/emergency applications. The unit is available to operate 3 Watt (700mA) constant current devices. The unit is designed to be used as a standalone unit and is able to pass through a 40mm cut out. The module is connected to the mains, battery and LED with simple irreversible plug & socket arrangements, for ease of installation. Technical Details PHL-EL3-S3W 12NC Voltage Range Power Rating - Non-Maintained Power Rating - Maintained Emergency Duration Charger Recharge Time Ballast Lumen output Volts AC 50/60 Hz 3.0 Watts 7.1 Watts 3 Hours 200mA 24 Hours 100% Discharge Current Tc Max Operation Mode Output Load Output Current Mounting Hole Size Module Size L x W x H Weight 1000mA 70 C Module / 50 C Battery Switchable Maintained/Non Maintained 3 Watt 700mA Designed to fit through 40mm Aperture 152mm x 26.5mm x 28.5mm (FC 144mm) 163g The units are suitable for use with the following Philips Emergency Batteries: PHB-EL3-C3-S 3.6V 4Ah NiCd BATTERY IN STICK FORMATION PHB-EL3-C3-FL 3.6V 4Ah NiCd BATTERY IN FLEXIBLE FORMATION PHB-EL3-M3-S 3.6V 4Ah NiMH BATTERY IN STICK FORMATION PHB-EL3-M3-T 3.6V 4Ah NiMH BATTERY IN TRIANGULAR FORMATION 7

8 LED Components PHL-EL3-3W 3 hour maintained driver for single 700mA LED The emergency PHL-EL3-3W is a combined switchable mains & emergency LED converter. The unit is available to operate 3 Watt (700mA) constant current devices. Technical Details PHL-EL3-3W 12NC Input Voltage Power Rating - Non-Maintained Power Rating - Maintained Emergency Duration Charger Recharge Time Ballast Lumen output Volts AC 50/60 Hz 3.0 Watts 7.1 Watts 3 Hours 200mA 24 Hours 100% Discharge Current Tc Max Operation Mode Output Load Output Current Module Size L x W x H Weight 1000mA 70 C Module / 50 C Battery Switchable Maintained/ Non Maintained 1 x 3 Watt 700mA 152mm x 26.5mm x 28.5mm (FC 144mm) 85g The units are suitable for use with the following Philips Emergency Batteries: PHB-EL3-C3-S 3.6V 4Ah NiCd BATTERY IN STICK FORMATION PHB-EL3-C3-FL 3.6V 4Ah NiCd BATTERY IN FLEXIBLE FORMATION PHB-EL3-M3-S 3.6V 4Ah NiMH BATTERY IN STICK FORMATION PHB-EL3-M3-T 3.6V 4Ah NiMH BATTERY IN TRIANGULAR FORMATION 8

9 Fluorescent Components PHF-EL3-L6 3 Hour Slimline EM Inverter Multi Watt The PHF-EL3-L6 low line 3 hour duration emergency lighting single ended inverter is specifically designed to fit in low line and T5 Luminaire profiles and to ensure complete performance compatibility with all types of fluorescent 4 pin lamps and their associated control gear. The inverter employs cathode pre heating and continuous heating to optimise lamp performance. The specified circuit and operation are selected at the time of installation by the method of wiring and connection. Features 4 Pole changeover relay - for total isolation of the control gear from the emergency inverter in the event of a test or emergency condition. Additional 5th pole HF relay Low profile metal case to suit low line luminaire profiles. Cathode Pre Heating Constant Cathode Heating Constant Current Emergency operation Open Circuit Lamp detect Deep discharge protection Technical Details PHF-EL3-L6 12NC Input Voltage Power Rating Watts Emergency Duration Charge Recharge Cut-Off Current Time Voltage Discharge Current Ambient Temp. TC Point TC Max. Temp. IP Rating Module Size L x W x H Overall Weight Volts AC 50/60 Hz 5.3 Watts 3 Hours 200mA 24 Hours 6.0 Volts 1.05 Amp 0 C to +50 C Case Side (Centre) 70 C IP20 300mm x 31.5mm x 21mm FC = 285mm 265g The units are suitable for use with the following Philips Emergency Batteries: PHB-EL3-C6-TS 7.2V 4Ah NiCd BATTERY IN TWIN STICK FORMATION 9

10 Fluorescent Components PHL-EL3-3, PHL-EL3-4, PHL-EL3-5 & PHL-EL3-6 3 Hour EM Inverter 4-36W, 4-58W, 4-70W, 4-100W CFL & T8 These 3 hour duration emergency lighting inverters are designed to suit multiple 4-pin fluorescent lamp wattages & circuits. The unit has the benefit of a 4 Pole changeover relay - for total isolation of the control gear from the emergency inverter in the event of a test or emergency condition. An additional 5th pole HF relay offers built in time delay to ensure the interconnected HF ballast does not see an open circuit condition when the fluorescent lamp is used in the emergency condition. The deep discharge protection circuit on the battery completely cuts off the battery load when fully discharged. The constant current charger circuit maintains the battery at peak condition to provide 3 hours emergency duration. The changeover operation from mains to emergency operation occurs between 60 and 85% of mains voltage in accordance with BS-EN Technical Details PHF-EL3-3 PHF-EL3-4 PHF-EL3-5 PHF-EL3-6 12NC Input Voltage Power Rating Watts Emergency Duration Volts AC 50/60 Hz 4.7 Watts 3 Hours Battery Voltage 3.6 Volts 4.8 Volts 6.0 Volts 7.2 Volts Charge Current Recharge Time 200mA 24 Hours Cut-Off Voltage 3.0 Volts 4.0 Volts 5.0 Volts 6.0 Volts Discharge Current Ambient Temperature TC Point 1.05 Amp 0 C to +50 C Case Side (Centre) TC Max. Temperature 70 C IP Rating Dimensions Suitable Batteries IP20 165mm x 45mm x 29mm (FC 155mm) Module Weight 320g 320g 320g 320g 10

11 Fluorescent Components PHF-EL3-3/14, PHF-EL3-4/14-24, PHF-EL3-6/35-49 & PHF-EL3-6/ Hour EM Inverter for 14W, 14 & 24W, 35 & 49W, 28 & 54W T5 Lamps These 3 hour duration emergency lighting inverters are designed to suit T5 (T16) fluorescent lamps. The unit has the benefit of a 4 Pole changeover relay - for total isolation of the control gear from the emergency inverter in the event of a test or emergency condition. An additional 5th pole HF relay offers built in time delay to ensure the interconnected HF ballast does not see an open circuit condition when the fluorescent lamp is used in the emergency condition. The deep discharge protection circuit on the battery completely cuts off the battery load when fully discharged. The constant current charger circuit maintains the battery at peak condition to provide 3 hours emergency duration. The changeover operation from mains to emergency operation occurs between 60 and 85% of mains voltage in accordance with BS EN Technical Details PHF-EL3-3/14 PHF- EL3-4/14-24 PHF- EL3-6/28-54 PHF- EL3-6/ NC Input Voltage Power Rating Watts Emergency Duration Battery Type Volts AC 50/60 Hz 4.7 Watts 3 Hours 4.5Ah Nickel Cadmium Battery Voltage 3.6 Volts 4.8 Volts 7.2 Volts Charge Current Recharge Time 200mA 24 Hours Cut-Off Voltage 3.0 Volts 4.0 Volts 6.0 Volts Discharge Current Ambient Temperature TC Point 1.05 Amp 0 C to +50 C Case Side (Centre) TC Max. Temperature 70 C IP Rating Module Size L x W x H Suitable Batteries IP20 165mm x 45mm x 29mm (FC 155mm) Module Weight 320g 320g 320g 320g 11

12 Fluorescent Components PHF-EL3-6/55 3 Hour EM Inverter for Amalgam and 2D Lamps up to 55W The PHF-EL3-6/55 3 hour duration emergency lighting inverter are designed for low mercury/amalgam type fluorescent lamps and is also suitable for use with free mercury type lamps (see lamp compatibility chart on page 17). The unit provides continuous lamp cathode heating and has the benefits of a 4 Pole changeover relay - for total isolation of the control gear from the emergency inverter in the event of a test or emergency condition. An additional 5th pole HF relay offers built in time delay to ensure the interconnected HF ballast does not see an open circuit condition when the fluorescent lamp is used in the emergency condition. The deep discharge protection circuit on the battery completely cuts off the battery load when fully discharged. The constant current charger circuit maintains the battery at peak condition to provide 3 hours emergency duration. The changeover operation from mains to emergency operation occurs between 60 and 85% of mains voltage in accordance with BS EN Technical Details PHF-EL3-6/55 12NC Input Voltage Power Rating Watts Emergency Duration Battery Type Battery Voltage Charge Current Recharge Time Volts AC 50/60 Hz 4.7 Watts 3 Hours 4.5Ah Nickel Cadmium 7.2 Volts 200mA 24 Hours Cut-Off Voltage Discharge Current Ambient Temp. TC Point TC Max. Temp. IP Rating Module Size L x W x H Module Weight 6.0 Volts 1.05 Amp 0 C to +50 C Case Side (Centre) 70 C IP20 165mm x 45mm x 29mm (FC 155mm) 370g The units are suitable for use with the following Philips Emergency Batteries: PHB-EL3-C6-TS 7.2V 4Ah NiCd BATTERY IN TWIN STICK FORMATION 12

13 Batteries Philips Emergency Batteries Philips Emergency Lighting range of batteries are available in both nickel cadmium (NiCd) and nickel metal hydride (NiMH) compositions and in varying configurations to meet the needs of a wide range of luminaire dimensions. The 4Ah capacity of the batteries provides 3 hours duration when used in conjunction with Philips emergency lighting modules. It is recommended by the British Standards that emergency lighting batteries are changed every four years. The NiCd batteries have a temperature limit of 55 C and the NiMH batteries have a temperature limit of 50 C. All the batteries are supplied with an irreversible plug and socket arrangement. The dimensions and weights of the batteries is as follows: PHB-EL3-C3-S 3.6V 4Ah NiCd BATTERY IN STICK FORMATION 220mm long x 37mm diameter f/c 205mm 382g PHB-EL3-C3-FL 3.6V 4Ah NiCd BATTERY IN FLEXIBLE FORMATION 270mm long x 38mm 399g PHB-EL3-C4-S 4.8V 4Ah NiCd BATTERY IN STICK FORMATION 280mm long x 37mm diameter f/c 265mm 506g PHB-EL3-C5-S 6V 4Ah NiCd BATTERY IN STICK FORMATION 340mm long x 37mm diameter f/c 325mm 633g PHB-EL3-C6-TS 7.2V 4Ah NiCd BATTERY IN TWIN STICK FORMATION 2 x 220mm long x 37mm diameter f/c 205mm each 756g PHB-EL3-M3-S 3.6V 4Ah NiMH BATTERY IN STICK FORMATION 243mm long x 21mm high x 22mm wide f/c 230mm 198g PHB-EL3-M3-T 3.6V 4Ah NiMH BATTERY IN TRIANGULAR FORMATION 70.5mm long x 37.5mm diameter 210g PHB-EL3-M4-TS 4.8V NiMH BATTERY IN TWIN STICK FORMATION 2x 170mm long x 21mm high x 22mm wide f/c 160mm each 273g PHB-EL3-M5-TS 6V NiMH BATTERY IN TWIN STICK FORMATION PHB-EL3-M6-TS 7.2V NiMH BATTERY IN TWIN STICK FORMATION 1 x 170mm long x 21mm high x 22mm wide & 1 x 243mm long x 21mm high x 22mm f/c 160mm & 230mm 331g 2 x 243mm long x 21mm high x 22mm wide f/c 230mm each 399g 13

14 Auxiliary PHI-EL3-24 Single Point 700mA Device for Downlight Applications The PHI-EL3-24 is a constant current 110 wide beam 3W LED complete with bi-colour charge LED. The unit is designed to fit in a variety of louvered luminaires. Technical Information Input Voltage Power Rating Max. Forward Current Beam Angle Cut Out Light Source Colour Colour Temp. Emitter Luminous Flux General CRI Tc Max Wiring Method Dimensions Weight 4V DC Max 3 watts 700mA mm x 12.5mm Cool White 6800K 114 Lumens C LED Backplate Series connection only via C4201 Series Plug 50mm x 16mm x 18mm (22mm inc. lead) 24g Spacing Table (in metres) Mounting To Wall Between Fittings Height

15 Auxiliary PHI-EL3-30P Single Point 700mA Device for Louvre Applications The PHI-EL3-30P is a constant current 110 wide beam 3W LED complete with bi-colour charge LED for use in downlighters. Technical Information Input Voltage Power Rating Max. Forward Current Beam Angle Light Source Colour Colour Temp. Luminaire Output General CRI Tc Max Wiring Method Dimensions Weight 4V DC Max 3 watts 700mA 110 Cool White 6000K 123 Lumens C LED Backplate Series connection only via C4201 Series Plug Ø 23mm x 50mm 42g Spacing Table (in metres) Mounting To Wall Between Fittings Height n/a n/a

16 PHI-EL3-LI, PHI-EL3-L1D and PHI-EL3-SR Green Charge Indicating LED With Holder Bi Colour Charge Indicating LED With Holder For DALI Modules Ceiling Recessable Charge LED Holder Philips charge indicators are available in two formats. The PHI-EL3-LI has a green lens and is compatible with most of our modules. The PLI-EL3-LI-D is bi colour and would be compatible with the PHL-EL3-D and PHL-EL3-D80 modules. This version is lit green in standard operation and flashes red to indicate a fault. All charge LEDs are supplied with a 500mm lead for connection to the module and a mounting collar. If there is no space to mount the indicator to the body of a luminaire, then the PHI-EL3-SR can be used to recess the indicator into the ceiling adjacent to the fitting. Range Overview LED Modules Flourescent Modules Batteries LED Auxiliary LED Indicator 12NC Product Code Product Description PHL-EL3 3 HOUR EM CONVERTER FOR 6-55V LED LOADS PHL-EL HOUR EM CONVERTER FOR 15-80V LED LOADS PHL-EL3-D 3 HOUR EM DALI CONVERTER FOR 6-55V LED LOADS PHL-EL3-D80 3 HOUR EM DALI CONVERTER FOR 15-80V LED LOADS PHL-EL3-4 3 HOUR EM CONVERTER FOR V LED LOADS PHL-EL3-S3W 3 HOUR MAINTAINED DRIVER FOR SINGLE 700mA LED WITH STRAIN RELIEF PHL-EL3-3W 3 HOUR MAINTAINED DRIVER FOR SINGLE 700mA LED PHF-EL3-L6 3 HOUR SLIMLINE EM INVERTER MULTI WATT PHF-EL3-3 3 HOUR EM INVERTER 4-36W CFL & T PHF-EL3-4 3 HOUR EM INVERTER 4-58W CFL & T PHF-EL3-5 3 HOUR EM INVERTER 4-70W CFL & T PHF-EL3-6 3 HOUR EM INVERTER 4-100W CFL & T PHF-EL3-3/14 3 HOUR EM INVERTER FOR 14W T5 LAMPS PHF-EL3-4/ HOUR EM INVERTER FOR 14 & 24W T5 LAMPS PHF-EL3-6/ HOUR EM INVERTER FOR 35 & 49W T5 LAMPS PHF-EL3-6/ HOUR EM INVERTER FOR 28 & 54W T5 lamps PHF-EL3-6/55 3 HOUR EM INVERTER FOR AMALGAM & 2D / PLQ LAMPS UP TO 55W PHB-EL3-C3-S 3.6V 4Ah NiCd BATTERY IN STICK FORMATION PHB-EL3-C3-FL 3.6V 4Ah NiCd BATTERY IN FLEXIBLE FORMATION PHB-EL3-C4-S 4.8V 4Ah NiCd BATTERY IN STICK FORMATION PHB-EL3-C5-S 6V 4Ah NiCd BATTERY IN STICK FORMATION PHB-EL3-C6-TS 7.2V 4Ah NiCd BATTERY IN TWIN STICK FORMATION PHB-EL3-M3-S 3.6V 4Ah NiMH BATTERY IN STICK FORMATION PHB-EL3-M3-T 3.6V 4Ah NiMH BATTERY IN TRIANGULAR FORMATION PHB-EL3-M4-TS 4.8V NiMH BATTERY IN TWIN STICK FORMATION PHB-EL3-M5-TS 6V NiMH BATTERY IN TWIN STICK FORMATION PHB-EL3-M6-TS 7.2V NiMH BATTERY IN TWIN STICK FORMATION PHI-EL3-24 SINGLE POINT 700mA DEVICE FOR DOWNLIGHT APPLICATIONS PHI-EL3-30P SINGLE POINT 700mA DEVICE FOR LOUVRE APPLICATIONS PHI-EL3-LI GREEN CHARGE INDICATING LED WITH HOLDER PHI-EL3-L1D BI COLOUR CHARGE INDICATING LED WITH HOLDER FOR DALI MODULES Accessory PHI-EL3-SR CEILING RECESSABLE CHARGE LED HOLDER 16

17 Lamp compatibility chart and BLF% Wattage Lamp type PHF-EL3-3 PHF-EL3-4 PHF-EL3-5 PHF-EL3-3/14 PHF-EL3-4/14-24 PHF-EL3-6/28-54 PHF-EL3-6/35-49 PHF-EL3-6/55 PHF-EL3-L6 4 T TC-EL TC-EL Auxiliary 8 T TC-EL TC-DEL TC-EL TC-DEL T PL-R TC-DD PL-R TC-L TC-F TC-DEL TC-TEL T T T5-CIR T TC-L TC-F TC-DEL TC-TEL T TC-DD TC-TEL TC-L T TC-L T TC-F TC-DD T T5-CIR TC-L TC-TEL T T T5-CIR TC-L 7 55 TC-DD TC-TEL 6 58 T T T TC-L 5 *Recommended option in bold 17

18 Contact details: Guildford Philips Lighting, Philips Centre, Guildford Business Park, Guildford, GU2 8XH Tel: Dublin Philips Electronics Ireland Ltd, Philips House, South County Business Park, Leopardstown, Dublin 18 Tel: Royal Philips N.V. All rights reserved. Philips reserves the right to make changes in specifcations and/or to discontinue any product at any time without notice or obligation and will not be liable for any consequences resulting from the use of this publication. 08/ lighting.uk@philips.com