SB-2/3EX-SEMI. Semi Automatic Carton Sealing Machine. User Guide

Transcription

1 SB-2/3EX-SEMI Semi Automatic Carton Sealing Machine User Guide

2

3 SB-2/3EX-SEMI Semi Automatic Carton Sealing Machine User Guide Revised 02/20/2018 P/N Rev D Copyright and Trademarks Copyright Eastey Enterprises All rights reserved. All trademarks and brand names are the property of their respective owners. Eastey Enterprises, Inc Boone Ave. N. Brooklyn Park, MN Phone: (763) ; Fax (763) ;

4

5 Contents Safety... 7 Explanation of Symbols... 8 Introduction... 9 General System Description... 9 Specifications Dimensions Installation Location Requirements Operation Loading the Tape Cartridges Check Tension Thread Tape Main Spring Power Control Panel Adjustments Air Pressure unit Height and Width Adjustment Flap Closing Guide Adjustment Belt Adjustment Machine Body Height Adjustment Maintenance Rollers Cutting Knives Troubleshooting Parts List Electrical Pneumatic Parts Side Belt Column Flap Guide Assembly Machine Body Door Guard Assembly Appendix A: Electrical Schematic Warranty Statement Customer Support... 57

6

7 Safety 7 Safety General Safety Precautions Before installing, operating or servicing this equipment, please read the following precautions carefully: This machine is equipped with moving belts. Do not place hands near the rear of this unit when the belts are moving as fingers may be pinched where belts enter the frame. We suggest the use of a roller-type exit conveyor or pack table for your cases. Always remove boxes after they clear the exit end of the machine. Observe caution when near the tape applying cartridges or when threading tape. The knife is very sharp, automatically operated, and is linked to the wipe down rollers. Always disconnect electrical power before attempting maintenance for any electrical or moving parts. Do not attempt to open or work on the electrical box, junction boxes, or other electrical components of the unit without first disconnecting power to the machine. Electrical shock hazard exists if power is not disconnected. Do not by-pass any factory-designed safety features such as knife guards, interlocks, switches, etc. Do not place hands or body inside the confines of the machine unless the head mechanism is securely fastened, and the electrical supply is shut off. To minimize the potential for personal injury, always be sure that the machine operators and others working on the machinery are properly trained in the correct usage of the equipment and properly instructed regarding safe operation. Never provide service or clear a box jam when machine is running. When feeding a box into the unit, always hold down the box top and present the box to unit. Release hands as soon as the belts begin to take the box. Do not wear loose clothing such as ties, scarves, jewelry etc. Long hair should be pulled back and/or covered while operating this machine.

8 8 Safety Explanation of Symbols Caution sign or Safety Alert symbol. Indicates caution, be alert, Your safety is involved. Knowledge of safe operation is required. Caution indicates a hazardous situation which, if not avoided, could result in minor or moderate injury or damage to equipment or surroundings. Electrical hazard. Indicates electrical danger. Only a trained electrician can uncover the electrical panel or box. Warning symbol. Indicates a hazardous situation which, if not avoided could result in death or serious injury. A warning indicates a situation or condition potentially more severe than indicated by a caution message but not imminent as a danger message. This symbol is associated with warnings for conditions as shown below. WARNING BLADE MAY CUT YOUR FINGER WARNING DO NOT TOUCH THE BELT WHEN THE MACHINE IS RUNNING

9 Introduction 9 Introduction General System Description Flap Folding Assembly Drive Belt Optional Alarm Signal Light Stack Guard Doors Panels for near side shown removed. Vertical Column Tape Head Optional Tape Low / Out Sensors Height Adjustment Crank Optional Exit End Roller Table Infeed End Adjustable Legs Control panel with Start/Run and Stop buttons, and Emergency Stop Width Switch (E-Stop) Adjustment Crank Electrical Box Locking Casters Main Power Switch

10 10 Introduction Specifications Model Tape Belt speed Capacity Consumption Machine size Machine net weight Air SB-2/3EX-SEMI 1.5 inches or 2 inches 75 ft/min (L) 4.7 to 24 inches (W) 4.3 to 19.5 inches (H) 4.7 to 19 inches 450 W With Guard Doors (L) 84 inches (W) 35.5 inches (H) 66.1 inches Machine Frame Length (L) 66 inches 660 lbs. 80 psi Electrical Belt motor Machine power use Power socket need 0.18KVA 0.4KVA 0.5KVA Options 3 tape head Infeed end roller table Exit end roller table Tape low/out sensing with alarm signal light stack

11 Introduction 11 Dimensions Dimensions shown in inches. 84 in. Overall Standard Machine Length with Guards 35.5 in. 30 in in. 66 in. Machine Roller Table Length Guards Extend 18 in. Beyond Infeed End in. Floor to Top of Column Max. 27 in. Min. to Roller 34.5 in. Max. Height

12 12 Introduction Dimensions with Optional Roller Tables and Tape Low / Out Sensors and Alarm Signal Light Stack Dimensions shown in inches.

13 Installation 13 Installation Carefully unpack the outer carton. Avoid damaging the machine body. Remove the banding straps that secure the carton sealer to the shipping pallet. Lift the carton sealer off the pallet. CAUTION! The SB-2/3EX-SEMI Carton Sealer is a very heavy piece of equipment and will require a forklift or floor crane to move safely off the shipping pallet. Install the four (4) casters on the carton sealer legs. Thread each caster into the bottom of each leg while supporting the carton sealer. To adjust the leg height, loosen the screws on each leg and slide the insert up or down. Leg Leg Insert Thread caster threaded stud into threaded hole in bottom of leg insert. Adjustment Screws Caster Loosen screws, slide leg insert up or down, and then retighten screws to secure at required height. Lock CAUTION! Raise the carton sealer off the floor to install the casters. Use proper equipment when lifting the carton sealer. Ensure the carton sealer is secure and will not shift while the casters are being installed.

14 14 Installation To move the SB-2/3EX-SEMI Carton Sealer to the desired location you will need to use a pallet jack or fork lift. If you have purchased the optional locking casters you can move the taper easily over a smooth flat surface. Location Requirements When installing the SB-2/3EX-SEMI Carton Sealer please be aware of the following considerations: 1. The mounting surface is flat and level. 2. Conveyor or packing table height. 3. Alignment with packaging line. When the SB-2/3EX-SEMI Carton Sealer is positioned in the operating location you will need access to: 1. The main power switch and control panel containing Start/Run button, Stop button, and Emergency Stop (E-Stop). 2. Height and width adjustments. 3. Both upper and lower tape cartridges for tape loading. 4. Air line supply hose and air filter/regulator assembly. A packing table may be provided at the infeed end where the packer can fill boxes and position the flaps while feeding the boxes into the machine for closing and sealing. It is also convenient to have a pack table at the exit end of the taper. It is essential that the table and conveyor be at the machine bed height. The machine should be placed on a flat, level floor so that it does not rock or move. We recommend that the machine be securely locked in place when used. Connect the air hose to the filter/regulator assembly on the side of the machine.

15 Operation 15 Operation Loading the Tape Cartridges Turn the main power switch to Off and disconnect the power. CAUTION! To avoid personal injury, remove the tape cartridge before loading tape. When handling the tape cartridge be careful to avoid contact with the tape cutting blade. After the taping cartridge has been removed push the tape roll onto the tape core assembly. NOTE: Make sure the tape roll is pushed all the way on the spindle assembly. Spindle Tape Roll Tape Core

16 16 Operation Check Tension Check the tape for correct tension. Tighten or loosen the tape core holder to adjust tension. Thread Tape Carefully thread the new tape through the rollers in the tape head as shown in the applicable diagram in the Tape Head User Guide provided with the tape head. For convenience, diagrams for threading tape in the Eastey-EX Tape Head and EZ-EX Tape Head are provided on the following page. Follow the diagram that applies for your tape head, depending on the tape head model and position on the taper.

17 Operation 17 Eastey-EX Tape Head Adhesive Side EZ-EX Tape Head Bottom Cartridge Upper Cartridge Adhesive Side Adhesive Side Bottom Cartridge Upper Cartridge Adhesive Side

18 18 Operation Center Tape Eastey-EX Tape Head only Make sure the tape is centered on all the rollers. There are several rollers in the tape cartridge where the tape alignment should be checked to verify the tape stays on center as it is being dispensed. Return the tape cartridge to the operation position. Main Spring For sealing light weight boxes, decrease the main spring tension. For heavier boxes, increase the main spring tension. Main Spring When setting tension for the rollers, consider the amount of pressure on the box flaps required to make the seal. Cartons completely filled to the top with product may require more pressure on top and bottom seams when applying tape than partially-filled cartons, where excessive pressure could possibly crush the carton.

19 Operation 19 Power Plug the power supply cord into a properly wired and grounded outlet. With the Main Power switch set to the On position, press the Start button. CAUTION! When the power is turned on be aware of moving parts and belts When the main power switch is On and there is power to the carton sealer, the Power Indicator light illuminates. Control Panel Start Stop Emergency Stop Power Indicator Light Main Power Main Power (Red with Yellow bezel) Switch the main power switch to On or Off to turn power to the carton sealer On or Off.

20 20 Operation Power Indicator Light (White) When the main power switch is On and there is power to the carton sealer, the Power Indicator light illuminates to indicate the machine is powered up and ready to run. When the main power switch is Off and the carton sealer is not in operation, the Power Indicator is not lighted. Stop Button (Red) Press the Stop button to stop the machine motors and belts. Start / Run Button (Green) Press the start button to start the automatic or manual program running. Emergency Stop Button (Red with Yellow label) Press the red Emergency Stop button for emergency stop. To reset the Emergency Stop button once the emergency condition is cleared and it is safe to operate the machine again, press the Emergency Stop button in while turning it approximately a quarter-turn in the direction of the arrow.

21 Adjustments 21 Adjustments Air Pressure unit The air pressure is pre-set at the factory to 80 PSI. The air pressure can be changed up or down for specific requirements. Make any changes to the air pressure in small increments. Inspect periodically to make sure the drain system is functional and properly lubricated. Air Pressure Adjustment Knob Air Supply Line Air Pressure Gauge Connect Air In Drain

22 22 Adjustments Height and Width Adjustment With the power off, place an appropriate size carton in the Case Sealer. Use the drive belt width adjustment crank to set the drive belt width to the correct box width. Set Screw Drive Belt Width Adjustment Crank Use the height adjustment crank to set the upper tape head to the correct box height. Height Adjustment Crank The height and width cranks can be used on either side of the machine by loosening the set screw and removing the crank, and then mounting the crank on the opposite side and re-tightening the set screw. One crank has a foldable handle so the handle can be folded in, and out of the way when the crank is not in use. Both cranks are interchangeable.

23 Adjustments 23 Loosen the locking knobs on the top squeezer alignment rollers to set the top width to the correct box width, and then re-tighten the locking knobs. This will insure the box stays centered. Locking Knob Top Squeezer Rollers Flap Closing Guide Adjustment When front cardboard flap touches the front flap folder, the front flap will be folded to approximately 60, as shown below. Front Flap Folder Approximately 60 Box Side View

24 24 Adjustments Side flaps will be closed while carton is moving forward and reaches the two closing arms. The ideal angle for the two closing arms is 30 degrees as shown in the top view. The closing arms are set to an angle of 15 degrees incline (note: The arms are moveable and adjustable in two ways, both height & width see below). Closing Arm Top View 30 Box Closing Arm Side View 15 Box Closing arm adjustments, if required, are made at the top of each end of the arm where they attach to angle brackets at the front and rear. Arms are moveable and adjustable for both height and width. Closing Arm Adjustment

25 Adjustments 25 There are two small air valve knobs used to adjust the speed of the rear flap-closing arm. One knob will adjust the down speed and the other is for the retraction speed. The rear closing arm pressure is pre-set at the factory. If you need to change the preset pressure, make changes in small increments. Adding too much pressure can cause the arm to go down too fast and too hard. Down Pressure Adjustment Knob Retract Pressure Adjustment Knob Belt Adjustment You do not have to remove the drive belt cover to adjust the drive belt. To adjust the belt, use an Allen wrench and loosen the belt nut. Adjust the belt to a suitable tension by turning the adjustment screw with a Phillips screwdriver. Re-tighten the belt nut. Allen Wrench Phillips Screwdriver

26 26 Adjustments Machine Body Height Adjustment To adjust the leg height, loosen the screws on each leg and slide the insert up or down. When the leg is at the desired height, retighten the adjustment screws to secure the leg height. Adjustment Screws Loosen screws, slide leg insert up or down, and then retighten screws to secure at required height. CAUTION! Ensure the case taper is secure and will not shift while adjusting leg height. Tape Head Adjustment Refer to Tape Head User Guide. Refer to instructions in the Tape Head User Guide that is provided with the tape head for instructions regarding adjustment information for the tape head.

27 Maintenance 27 Maintenance The SB-2/3EX-SEMI Industrial Case Taping System will provide many hours of maintenance free operation. There are a few items that may require attention from time to time. Rollers Make sure rollers stay clean and grease free. If you should have to clean the rollers simply wipe them down with a clean lint free cloth. If a more thorough cleaning is necessary wipe the rollers down with a mild detergent and water and let dry. Never use harsh or abrasive cleaners or chemical agents when cleaning the rollers. Cutting Knives Occasionally inspect the cutting knives to ensure they are clean and free of adhesive residue. Make sure the cutting knife is sharp by inspecting cuts in the tape. Cuts should be straight and neat. If the quality of cuts is eroding, the knife blade is dull and should be replaced. Changing Knife Blades Refer to Tape Head User Guide Turn off and unplug the taper. It is not necessary to remove either tape head to change the blade. Refer to the Tape Head User Guide provided with the tape head for instructions for changing the knife blades. CAUTION! Always be aware of the cutting edges while replacing the knife blades. Handle the knife blades carefully.

28 28 Troubleshooting Troubleshooting Problem Possible cause Solution Taper will not start. Machine is not connected to power. The Emergency Stop button is pressed in. Start button has not been pressed. Blown Fuse. Machine is not operating. Machine has inadequate electrical power or power is not connected. The air pressure may not be sufficient. Air cylinder on the flap closing system does not work. Indexing gate (stopper), doesn t operate. Machine cannot tape cartons. Kinked hoses and/or wiring. (a) Bent or twisted hoses and wiring. (b) Defective infeed or exit photo eyes sensors. The side belts or squeeze rollers are not correctly adjusted for the box size. Check power input. Verify power connection. Release the Emergency Stop button. Press the Start button to start the automatic or manual program running. Check power/overload condition, then replace fuse if blown. Verify system power meets specification requirements. Adjust the air Pressure. Reposition the hoses and wiring. (a) Re-position hoses and wiring. (b) Adjust the position of photo eye, or replace a new one. Use the width adjustment crank to adjust the side belt width. Check width of squeeze rollers. Start Button Indicators Start button flashes 1 time. Start button flashes 2 times. Start button flashes 3 times. Start button does not flash. Normal operation. The motor is overloaded. Stop button is on or wiring problem. Check wiring. (a) Turn on the power, power (indication light will be on). (b) Release the E-Stop. (c) Close all guard doors.

29 Troubleshooting 29 Problem Solution Stuck carton Check drive belt width adjustment. Check for proper height adjustment. Uneven or poor tape cuts Adjust knife arm spring tension. Adjust wipe roller spring tension. Replace cutting knives. Uneven Tape Leg on Front Tape tension is too low. Tighten the one-way clutch roller and/or the tape core. Adjust the one-way clutch roller in the slot so it is slightly beyond the front wipe roller. Adjust the tape leg length. See Tape Leg Adjustment section. Uneven or Torn Tape Blade is dull. Replace Blade. Tape tension is incorrect. Increase tension. Clean and adjust blade. Blade mounted incorrectly or backwards. Knife arm spring is worn. Replace knife arm spring. Adjust cartridge height. Tape Folding Check that all rollers turn freely. Check to be sure tape is threaded properly on front roller (refer to Tape Head User s Manual).

30 30 Troubleshooting Problem Tape Curling and Bunching Up Eastey EX Tape Head Only Solution Eastey-EX Tape Head Only Adjust the tape cartridge height (approximately.06 inches from box) Check tape tension set by the spring tension at the tape core.

31 Illustrated Parts List 31 Parts List Electrical 31 Optional Alarm Signal Light Stack 32 Optional Tape Low / Out Sensors Optional Exit Roller Table

32 32 Illustrated Parts List Electrical Continued Panel Layout

33 Illustrated Parts List 33 ITEM PART NO. DESCRIPTION Q TY 1 P SEPARATED POWER ON/OFF C064 ½ 90 CONNECTOR (BVWD-G027GT) /152P003 TERMINAL BLOCKS TB6P 1 5 P POWER SUPPLY RS P CIRCUIT BREAKER IK60N2PC16A 1 7 P CIRCUIT BREAKER IC60N1PC2A R RELAY LY2 DC24V FIXED REED PYCA B301 RELAY SEAT LY PLC VIGOR VH-24MR CONTACTOR LC1-D096BL (DC24V) THERMAL OVERLOADRELAY(110V)(4~6A) THERMAL OVERLOADRELAY(220V)(2.5~4A) TC10 TERMINAL POST 28P ON/OFF SWITCH BOX XALD AW01 AUTO RUN GREEN LAMP COVER AL01 BUTTON RED ZB5-AL HP22 SLEEVE P EMG.SWITCH AW02 AUTO RUN GREEN LAMP ZB5-AW LD01/109A011 LED LAMP DL1-LED ZE01 (START)(STOP)BUTTON SEAT CONTACTOR(NOx1) ZB5-AZ AZ03 EMG. BUTTON SEAT CONTACTOR NCx FIXING PLATE TBR-F CD01 PHOTO SENSOR CDR-10X BVB1/109A010 WHITE LAMP XB2BVB1C CD02 OPTIONAL PHOTO SENSOR CDR-10X-M CD02-01 OPTIONAL PHOTO SENSOR CONTACTOR LINE BD30/104L003 OPTIONAL SELECTOR SWITCHES ZB2-BD3C BZ13 / 104L001-2A OPTIONAL BUTTON SEAT CONTACTOR ZB2-BZ103C P003 SAFETY SWITCH TZ-93BPG 2

34 34 Illustrated Parts List ITEM PART NO. DESCRIPTION Q TY P003 SAFETY SWITCH KEY TZ93-K KA OPTIONAL ALARM LIGHT TOWER KA OPTIONAL ILLUMINATED units XVMC33 (Green) KA OPTIONAL ILLUMINATED units XVMC34 (Red) KA OPTIONAL ILLUMINATED units XVMC35 (Orange) KA OPTIONAL BASE unit XVM-c29B KA OPTIONAL Fixing bases SVM-Z KA OPTIONAL LEDs LC1-EDBS5W/24V 3

35 Pneumatic Parts Illustrated Parts List 35

36 36 Illustrated Parts List ITEM PART NO. DESCRIPTION Q TY AIR F.R.L UNITS (MAFR300-8A-D) CCNNECTOR (PL8-02) CCNNECTOR MPP PRESSURE GAUGE SOLENOID VALVE BRASS SILENCER CCNNECTOR (PC8-02) SLEEVE (1/4 ) SLEEVE (1/8 ) CCNNECTOR (PE8) CCNNECTOR (JSC8-01A) ISO CYLINDER (MCQV ) ISO CYLINDER (MCMA-11-32*50(90 ) CONNECTOR, JSC8-02A CONNECTOR, PLF CONNECTOR, PL6-M P CONNECTOR, PG CONNECTOR, PC-1/ P CONNECTOR, PY CONNECTOR, BCN CONNECTOR, BTF CONNECTOR, PC8-1 1

37 Illustrated Parts List 37 Side Belt

38 38 Illustrated Parts List ITEM PART NO. DESCRIPTION Q TY 1 P A BELT COVER SCREW M6 12L 6 3 P BELT 1 4 CA PULLEY DRIVER 2 5 CA30250A MOTOR SHAFT BEARING CA MOTOR SEAT BEARING 6003ZZ 2 9 CA UNIVERSAL JOINT L1 MOTOR 110V/60HZ,T18: L1 MOTOR 220V/60HZ,T18: L L2 MOTOR 220V/50HZ,T15:1 MOTOR 240V/50HZ,T15: L1 MOTOR 380V/50HZ,T15: L1 MOTOR 400V/50HZ,T15: RING S CA PULLEY SHAFT CA PLASTIC PULLEY CE SPEDIAL SCREW 6 15 P A SUPPORT COLUMN 1 16 CA3010L0 GUIDE PLATE SCREW M8 70L 2 18 CA PULLEY FOLLOWER BEARING 6003ZZ 4 20 CA PULLEY SHAFT 2 21 CE SUPPORT SHAFT 4 22 CA ADJUSTMLNT BLOCK 2 23 CA SHAFT SEAT 4 24 CA3015L0 SPINDLE SUPPORT 2 25 CA SPINDLE WIDTH ADJUSTMENT 1 26 CA3015R0 SPINDLE SUPPORT S35D CHAIN # P A HANDLE CRANK ARM 1 29 CA HANDLE RING 2 30 CA SPINDLE WIDTH ADJUSTMENT 1 31 CA CHAIN SPPOCKET 12T 2 32 P A BELT COVER 1

39 Illustrated Parts List 39 ITEM PART NO. DESCRIPTION Q TY 33 CA3010R0 GUIDE PLATE 1 34 P A SUPPORT COLUMN R1 MOTOR 110V/60HZ,T18: R1 MOTOR 220V/60HZ,T18: R R2 MOTOR 220V/50HZ,T15:1 MOTOR 240V/50HZ,T15: R1 MOTOR 380V/50HZ,T15: R1 MOTOR 400V/50HZ,T15: CA BUSHING 2 37 CA CHAIN WHEEL 1 38 CA CHAIN WHEEL SHAFT SCREW M6 25L 1 40 P WASHER 4 41 P CUSHION ASSEMBLY (L) P CUSHION ASSEMBLY (R) CA SHAFT 1

40 40 Illustrated Parts List Column

41 Illustrated Parts List 41 ITEM PART NO. DESCRIPTION Q TY 1 KA COLUMN COVER FRAME 2 2 KA FIX SEAT 2 3 CA SHAFT SEAT 2 4 CA COPPR RING 2 5 KA TOWER FRAME COVER 4 6 KA GEAR (S45C) M=1.5, T= BEARING AXK AS05 WASHER AS KA SWITCH CAM 2 9 KA SHAFT 4 10 CA SCREW (RIGHT) 1 10 CA2309L0 SCREW (LEFT) 1 11 KA030538R0 COLUMN SCREW (RIGHT) 1 11 KA030538L0 COLUMN SCREW (LEFT) 1 12 KA FIX SEAT BEARING 6202ZZ(CWB) 2 14 CE COLUMN BEARING SEAT 2 15 KA WASHER 2 16 KA COLUMN C-RIGN S KA BRACKET 4 19 P A SCREW (RIGHT) 1 19 P A SCREW (LEFT) LM20 LINEAR MOTION BEARING LM-20UU C-RING S KA BRACKET BASE 2 23 KA SWITCH CAM 4 24 KA CRANK HANOLE 1 25 CA HANDLE RING 2 26 KA GEAR (POM)M=1.5,T= KA TRANSMISSION SHAFT 1 28 KA COVER FRAME (TOP) N BEARING 6002ZZ-NR(CWB) 2 30 KA FIX SEAT C-RINGS KA COVER FRAME 1

42 42 Illustrated Parts List Flap Guide Assembly

43 Illustrated Parts List 43 ITEM PART NO. DESCRIPTION Q TY 1 KA SUPPORT BAR 2 2 KA FOLDING DEVICE SEAT 1 3 KA SUPPORT PLATE 1 4 KA SUPPORT SEAT 1 5 KA110853L0 UPPER TAPE HEAD SEAT (LEFT) 1 6 KA CONNECT BAR 2 7 CA B PLATE 4 8 KA110853R0 UPPER TAPE HEAD SEAT (RIGHT) 1 9 KA TUBE FIXED SEAT 1 10 KA FIXED RING 4 11 CA HANDLE KNOB M10x KA LOCKING COVER 2 13 KA LOCKING SEAT 2 14 KA LOCKING PLATE RUBBER COVER 2 16 CA COMPRESSION ROLLER 4 17 CA COMPRESSION ROLLER SHAFT SCREW M6x12L 4 19 CA COMPRESSION ROLLER SEAT 2 20 CA SUPPORT BAR RUBBER COVER KA CONNECT SEAT 1 23 KA FOLDING DEVICE SEAT 1 24 KA FOLDING DEVICE BRACKET 1 25 KA FIXED HANDLE 4 26 KA FIXED SCREW 4 27 KA FOLDING DEVICE O ISO CYLINDER MCQV CB CYLINDER BASE MCQV CB-B CB PIN-CB-AL ROD END PHS12EC M12x KA ARM SHAFT 1 31 KA FOLDING ARM SEAT C-RING S N BEARING 6002ZZ-NR(CWB) 2 34 KA CYLINDER CONNECT SHAFT 1 35 KA FOLDING ARM 1 36 KA111161R0 FLAP DIVIDER SUPPORT 1

44 44 Illustrated Parts List ITEM PART NO. DESCRIPTION Q TY 37 KA111161L0 FLAP DIVIDER SUPPORT 1 38 KA PRESS SPRING 1 39 KA FIXED SEAT 1 40 KA FIXED PIN 1 41 KA FLAP DIVIDER 1 42 KA BUFFER 1

45 Illustrated Parts List 45 Machine Body ITEM PART NO. DESCRIPTION Q TY 1 P A MACHINE FRAME SCREW M6 12L 8 3 KA MACHINE LEG 4 4 KA CLAMP 4 5 KA FEXED PLATE 4 6 KA ADJUSTABLE LEG NUTN 1/2 4 8 KA CASTER 4 9 P A CONTROL BOX 1 10 CC WIRING PLATE 1 11 CC CONTROL BOX DOOR 1 12 CA ROLLER(LONG) CA ROLLER(SHORT) CA33070A B-PLATE 2 15 CA33060A A-PLATE 2

46 46 Illustrated Parts List ITEM PART NO. DESCRIPTION Q TY 16 KA CROSS BRACE LEG 2 17 CC RADIOTUBE PLATE 1 18 PA LOCK 2 18 PA KEY 2 18 PD PLATE 2

47 Illustrated Parts List 47 Door Guard Assembly Optional 33 Light Stack Components Optional Tape Low / Out 31 Sensors and Brackets Optional Exit End Roller Table (Same as Infeed End Roller Table.) Optional Tape 17 Low / Out Sensors 15 and Brackets Optional Infeed End Roller Table (Same as Exit End Roller Table.)

48 48 Illustrated Parts List ITEM PART NO. DESCRIPTION Q TY 1 CC OPTIONAL INFEED/OUTFEED TABLE FRAME 2 2 CA ROLLER ASSY P A INDEXOR SEAT (L) 1 4 P A INDEXOR SEAT (R) ISO CYLINDER MCMA-11-32* INDEXOR SEAT SHAFT U-SHAPE SLING BRACKET+SDB SHAFT M P A ROD END M KA SAFETY SWITCH SEAT P003 SAFETY SWITCH TZ93-BPG K003 SAFETY SWTCH KEY TZ93-K CE EXTENDED SHAFT BUSH 2 15 KA OPTIONAL PHOTO EYE SENSOR SUPPORT (INNER) 1 16 KA OPTIONAL PHOTO EYE SENSOR SUPPORT (OUTER) 1 17 KA FIXED SUPPORTING SEAT 2 18 KA PLATE KA ACRYLIC WINDOWPANE 2 20 P A SAFETY DOOR FRAME (L) 1 21 KA SUPPORTING PLATE 2 22 P A SAFETY DOOR FRAME (R) 1 23 PD L HINGE (L) 1 24 KA SAFETY DOOR 2 25 CE DOOR HANDLE 2 26 PD HINGE (R) 2 27 CE MAGNET 4 28 P A DOOR SUPPORT 1 29 P ACRYLIC DOOR CD02 OPTIONAL PHOTO EYE SENSOR 4 31 KA OPTIONAL PHOTO EYE SENSOR SUPPORT (INNER) 1 32 KA OPTIONAL PHOTO EYE SENSOR SUPPORT (OUTER) 1 33 KA OPTIONAL ALARM LIGHT SET 1 34 KA OPTIONAL ALARM LIGHT SEAT 1 Tape Head Refer to Tape Head User Guide. Refer to the parts illustrations and listings in the Tape Head User Guide provided with the tape head for identification and part numbers of tape head parts.

49 Appendix A: Electrical Schematic 49 Appendix A: Electrical Schematic

50 50 Appendix A: Electrical Schematic Electrical Schematic Continued

51 Electrical Schematic Continued Appendix A: Electrical Schematic 51

52 52 Appendix A: Electrical Schematic Electrical Schematic Continued

53 Electrical Schematic Continued Appendix A: Electrical Schematic 53

54 54 Appendix A: Electrical Schematic Electrical Schematic Continued

55 Warranty Statement 55 Warranty Statement SB-2/3EX-SEMI Carton Sealing Machine Warranty Statement Eastey Enterprises warrants that all of the products it ships will be in good working order and free from defects in material and workmanship and will conform to the published specifications for that product. Warranty Period Drive motor(s): Gear reducer: Tape head: All other parts: 1 year 1 year 1 year (Except for moving parts which are subject to normal wear, tear and replacement which are warranted to be free from defects in material and workmanship.) 1 year (Except for moving parts which are subject to normal wear, tear and replacement which are warranted to be free from defects in material and workmanship.) Taping Quality Taping quality achieved in a given application is dependent on the installation, the material handling, and the maintenance provided. Eastey makes no warranty that the taping quality achieved in an application will be the same as that achieved on a test piece in our demo facility. Shipping Policy Customer pays all incoming shipping. If the item is defective and under warranty, Eastey pays return shipping charges for least costly method. If expedited shipping is desired, customer must furnish his shipping account and shipping fees will be charged to that account. Warranty Verification If you conclude that a product may be defective and may be covered by warranty, obtain a Return Material Authorization number by calling our technical support number (toll free at , or or Fax ) or info@eastey.com, and return the defective item to Eastey. Eastey will analyze the product and, if found to be defective, we will, at our option, replace or repair the item. If the item is found to not be eligible for warranty, you will be notified and may decide on disposition. Defective products will be replaced or repaired as promptly as possible. Warranty Eligibility The warranty provided by Eastey Enterprises, Inc. is only to the original buyer.

56 56 Warranty Statement Limited Warranty THE ABOVE WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. Disclaimer of Damages REGARDLESS OF WHETHER ANY REMEDY SET FORTH HEREIN FAILS OF ITS ESSENTIAL PURPOSE, IN NO EVENT WILL EASTEY ENTERPRISES, INC. BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, INCLUDING LOST PROFIT OR LOST OPPORTUNITIES OF ANY TYPE ARISING OUT OF THE USE OR INABILITY TO USE THESE PRODUCTS EVEN IF EASTEY ENTERPRISES, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

57 Customer Support 57 Customer Support Eastey Technical Service For help setting up or operating the SB-2/3EX-SEMI Semi-Automatic Carton Sealer, please contact Eastey Technical Service at one of the numbers listed below. Toll-Free Phone Phone Fax Web Thanks again for your purchase of Eastey products. We are pleased to be a part of your packaging needs.

58