Technical Particulars and Guarantees of 2.5 MVA, 11/0.416kV Transformer No. Description Unit

Transcription

1 2.5 MVA 11/0.416kV Transformer Technical Particulars and Guarantees of 2.5 MVA, 11/0.416kV Transformer No. Description Unit Specification 1 GENERAL 1.1 Manufacturer Name SEA, ABB, Siemens, BEST, Schneider, MATELEC or equivalent 1.2 Country of Manufacturing 1.3 Type Oil immersed cable box for both H.V & L.V 1.4 Model To be filled in 1.5 Applicable Standards IEC Location of service Outdoor 1.7 Type Tests and Short circuit Test Report Certificate Provided Yes 2 RATINGS 2.1 Rated power MVA Rated voltage ratio Primary kv 11(±2 x 2.5%) Secondary kv 0.416Y/ Number of phase Frequency Hz Vector group symbol Dyn Cooling method ONAN 2.7 No load losses kw 2.8 Load loss at full load at 75 deg temperature kw 2.9 Maximum temperature rise at rated power Top oil by thermometer K 45 Winding by resistance K 50 Page 1 of 2

2 Technical Particulars and Guarantees of 2.5 MVA, 11/0.416kV Transformer No. Description Unit Specification 2.10 Impedance voltage at continuous rated power % 6 3 Rated insulation level for Primary Impulse withstand voltage kv (1.2/50µS) peak 75 One minute 50Hz withstand voltage kv rms 28 4 DESIGN DETAILS 4.1 Off-load tap changer Tapping range (±2 x 2.5%) Tapping step 2.50% 4.2 Type of oil (As per IEC requirement) SHELL DIALA B 5 DIMENSION AND WEIGHT 5.1 Dimension of Transformer (L x W x H) mm To be filled in 5.2 Total oil required (Volume) Liter To be filled in 5.3 Total weight of complete transformer including fitting and oil kg To be filled in Page 2 of 2

3 No. Description Unit GENERAL Manufacturer and country of origin 11 kv XLPE 1 Core 150 mm2 To Be Filled Applicable Standards IEC & IEC60228 Type To Be Filled Number of Cores Single/Three Single Voltage grade of cable Vo/V (Vmax) kv 12/20 (24) Conductor cross section area mm Rated Frequency Hz 50 Conductor details: Material Annealed Copper Wires Compacted Compacted Circular Stranded Number of wires in each conductor To Be Filled Area mm 2 To Be Filled Diameter of copper conductor mm To Be Filled Conductor screen: Material Semi Conductive compound Nominal thickness mm To Be Filled Insulation: Material XLPE Nominal thickness of insulation mm 5.5 Insulation Screen A. Semi-conducting screen (extruded) Specification 5 Material Semi Conductive compound Nominal thickness mm To Be Filled B. Semi-conducting tape Material To Be Filled Nominal thickness mm To Be Filled Width mm To Be Filled Page 1 of 2

4 Swelling Yes/No C. Metallic screen Material To Be Filled Electrical cross section mm 2 To Be Filled Number of wires To Be Filled Inner Sheath: 6 Material PVC ST2 Extruded Yes/No Nominal thickness mm To Be Filled Armour: 7 Material Yes/No Type To Be Filled Galvanizing thickness micron To Be Filled 8 Waterproof Tape Description To Be Filled Outer sheath: Material PVC ST2 9 Nominal thickness mm To Be Filled Termite resistant Yes/No Rodent resistant Yes/No Color Black Nominal overall diameter of completed 10 cable mm To Be Filled 11 Weight of completed cable Kg/m To Be Filled Maximum DC resistance of conductor at 12 Ω/km 20 C Maximum Partial Discharge at 1.5 Uo pc 5,according to IEC60840 Minimum Bending Radius of Cable 14 (during installation) mm To be filled in Maximum permissible pulling force at 15 total cable in drums kn To be filled in Cross section drawing and details of cables layers and Cable catalogues, 16 Includes catalogues for Cable Terminations. To Be Provided 17 Type Test Certificates To Be Provided Page 2 of 2

5 No. Description Unit GENERAL Manufacturer and country of origin 11 kv XLPE 1 Core 400 mm2 Page 1 of 2 To Be Filled Applicable Standards IEC & IEC60228 Type To Be Filled Number of Cores Single/Three Single Voltage grade of cable Vo/V (Vmax) kv 12/20 (24) Conductor cross section area mm Rated Frequency Hz 50 Conductor details: Material Annealed Copper Wires Compacted Compacted Circular Stranded Number of wires in each conductor To Be Filled Area mm 2 To Be Filled Diameter of copper conductor mm To Be Filled Conductor screen: Material Semi Conductive compound Nominal thickness mm To Be Filled Insulation: Material XLPE Nominal thickness of insulation mm 5.5 Insulation Screen A. Semi-conducting screen (extruded) Material Semi Conductive compound Nominal thickness mm To Be Filled B. Semi-conducting tape Material To Be Filled Nominal thickness mm To Be Filled Width mm To Be Filled Swelling Yes/No C. Metallic screen Material To Be Filled Electrical cross section mm 2 To Be Filled Specification

6 Number of wires To Be Filled Inner Sheath: 6 Material PVC ST2 Extruded Yes/No Nominal thickness mm To Be Filled Armour: Material Yes/No 7 Type To Be Filled Thickness of tape mm To Be Filled Galvanizing thickness micron To Be Filled 8 Waterproof Tape Description To Be Filled Outer sheath: Material PVC ST2 9 Nominal thickness mm To Be Filled Termite resistant Yes/No Rodent resistant Yes/No Color Black Nominal overall diameter of completed 10 cable mm To Be Filled 11 Weight of completed cable Kg/m To Be Filled Maximum DC resistance of conductor at 12 Ω/km 20 C Maximum Partial Discharge at 1.5 Uo pc 5,according to IEC60840 Minimum Bending Radius of Cable 14 (during installation) mm To be filled in Maximum permissible pulling force at 15 total cable in drums kn To be filled in Cross section drawing and details of cables layers and Cable catalogues, 16 Includes catalogues for Cable To Be Provided Terminations. 17 Type Test Certificates To Be Provided Page 2 of 2

7 11kV Metal Clad Switchgear Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification A 11kV METAL CLAD SWITCHGEAR 1 GENERAL 1.1 Manufacturer Name ABB, Schneider, Siemens or equivalent 1.2 Country of Manufacturing To be filled in 1.3 Type Air insulated 1.4 Model To be filled in 1.5 Applicable Standards IEC , IEC Type Test Certificate Provided Yes 1.7 Location of service Indoor 2 ELECTRICAL DATA 2.1 Rated voltage kv Rated insulation level Impulse withstand voltage (1.2/50µs) kv peak 75 One minute 50Hz withstand voltage kv rms Rated frequency Hz Rated normal current Busbar Bus Section/Bus Riser Incoming transformer feeder Outgoing A A A A Rated short-time withstand current ka rms 25/3s Equipment s Should Comply With AIS Technical Specifications Page 1 of 11

8 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification 2.6 Rated peak withstand current ka peak Rated duration of short circuit sec Rated supply voltage of closing and opening devices, auxiliary and control circuits Closing and Tripping V DC 110 Indication V DC 110 Control V DC DESIGN DETAILS 3.1 Busbars Type Rated current Single Busbar A 1500 Bus Section A 1250 Incoming transformer feeder A 1250 Outgoing feeder A 630 Temperature rise on continuous operation at current C To be filled in Cross section mm 2 To be filled in Insulation of busbar According to clause Maximum working temperature of busbar insulation C To be filled in Minimum clearance between phases mm To be filled in Minimum clearance between phases and earth mm To be filled in 3.2 Material cover Metallic Equipment s Should Comply With AIS Technical Specifications Page 2 of 11

9 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification partitions Metallic shutters Metallic / Earthed HV conductor copper Contacts Silver-plated copper 3.3 Minimum thickness of sheet metal used mm To be filled in 3.4 Color and type of painting Light gray finish 3.5 Degree of protection Enclosures Cable and Breaker Instruments Bus-bar IP40 IP41 IP50 IP Minimum compartments of cubicles at switchgear board 3.7 Busbar and feeder shutters lockable with individual manual and automatic features Busbar/ Circuit Breaker / Cable/ LVvoltage Compartment Yes 3.8 Pressure relief device Yes 4 DIMENSION AND WEIGHT 4.1 Dimensions (L x W x H) Transformer Cubicle m 0.63 Bus Section Cubicle m 0.63 Bus Riser Cubicle m 0.63 Outgoing Cubicle m 0.63 Future Capacitor Bank Cubicle m N.A Aux. transformer Cubicle m N.A Equipment s Should Comply With AIS Technical Specifications Page 3 of 11

10 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification 4.2 Weight B Transformer Cubicle kg To be filled in Bus Section Cubicle kg To be filled in Bus Riser Cubicle kg To be filled in Outgoing Cubicle kg To be filled in Future Capacitor Bank Cubicle kg To be filled in Aux. transformer Cubicle kg To be filled in CIRCUIT BREAKER 1.1 Manufacturer Name ABB, Schneider, Siemens or equivalent 1.2 Country of Manufacturing To be filled in 1.3 Type Vacuum, triple pole operation,truckmounted,withdrawable 1.4 Model To be filled in 1.5 Applicable Standards IEC Number of poles Location of service Inside metal clad switchgear 1.8 Type of operating mechanism Motor charged spring 1.9 Type Test including extended mechanical endurance test Certificate Provided Yes 2 ELECTRICAL DATA 2.1 Rated voltage kv Rated insulation level Impulse withstand voltage (1.2/50µs) kv peak 75 Equipment s Should Comply With AIS Technical Specifications Page 4 of 11

11 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification One minute 50 Hz withstand voltage kv rms Rated frequency Hz Rated current Incoming A 1250 Bus Section A 1250 Outgoing feeder A Rated peak withstand current ka peak Rated Short time withstand current ka rms Rated duration of short circuit sec Rated supply voltage of closing and opening devices, auxiliary and control circuits Closing and Tripping V DC 110 Motor V DC 110 Indication V DC 110 Control V DC Rated Short time breaking current Cable charging A 25A Line charging A 10A 2.10 Rated Short time Breaking current ka Rated operating sequence for double reclosing 3 DESIGN DETAILS O-0.3sec-CO- 3min- CO 3.1 First pole-to-clear factor Rated transient recovery voltage kv/ µs To be filled in 3.3 Total interrupting Sec. Max 0.1 Equipment s Should Comply With AIS Technical Specifications Page 5 of 11

12 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification Closing time Sec. To be filled in Opening time Sec. To be filled in Operation Time (Make/Break) Not more than 3 cycle 3.4 Operating mechanism Motor charged spring stored energy 3.5 Spring charging time at rated operation voltage 3.6 Temperature rise of main contacts continuous operation at rated current 3.7 C.B is trip-free or with lock-out preventing closing 3.8 Rated supply voltage for Sec. To be filled in C To be filled in Trip free with antipumping device Closing coil V DC 110 Shunt opening release V DC 110 Motor V DC Power consumption Closing coil VA To be filled in Shunt opening release VA To be filled in Motor VA To be filled in 3.10 Number and type of spare auxiliary Switches 3.11 Auxiliary switch 8NO+8NC Continuous current carrying capacity A To be filled Breaking capacity at 110V DC A To be filled 3.12 Guaranteed number of breakings without necessity to inspect the circuit breaker poles 3.13 Guaranteed number of operations with no load without necessity to inspect the 20 10,000 Equipment s Should Comply With AIS Technical Specifications Page 6 of 11

13 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification circuit breaker poles & operating mechanism Type of corrosion protection of steel parts 4 DIMENSION AND WEIGHT Zinc chromate Plating and painting 4.1 Dimensions (L x W x H) of Circuit m To be filled in Breaker 4.2 Weight of Circuit Breaker kg To be filled in C EARTHING SWITCH 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type Fault making Airinsulated, manual operation type 1.4 Model To be filled in 1.5 Applicable Standards IEC Location of service Inside metal clad switchgear 1.7 Number of poles 3 2 ELECTRICAL DATA 2.1 Rated voltage kv Rated insulation level Impulse withstand voltage (1.2/50µs) kv peak 75 One minute 50Hz withstand voltage kv rms Distance between open contacts for DS mm To be filled in 2.4 Rated short-time current at time duration of 3 sec. for main contacts and earthing switch ka 25 Equipment s Should Comply With AIS Technical Specifications Page 7 of 11

14 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification 2.5 Making capacity for main contacts and ka To be filled in earthing switch 3 DESIGN DETAIL 3.1 Minimum Clearance in air Between poles mm To be filled in To earth mm To be filled in 3.2 Type of operating mechanism Manual 3.3 Type of interlocking mechanism interlocked between CB and ES 3.4 Number and type of spare auxiliary Switches 3.5 Auxiliary switch Mechanical with padlock 5NO+5NC D Continuous current carrying capacity A To be filled in Breaking capacity A To be filled in CURRENT TRANSFORMERS 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type Molded type Indoor 1.4 Model To be filled in 1.5 Applicable Standards IEC ELECTRICAL DATA 2.1 Rated voltage kv Rated primary current Transformer feeder A According to Single line Diagrams Bus Section A According to Single line Diagrams Equipment s Should Comply With AIS Technical Specifications Page 8 of 11

15 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification Outgoing feeder A According to Single line Diagrams Aux. transformer feeder A N.A. 2.3 Rated secondary current Measuring A 5 Protection (O/C, E/F) A 5 Protection (Differential) A N.A 2.4 Rated short-time thermal current ( 3 ka 25 sec) 2.5 Rated dynamic current ka peak Rated insulation level Impulse withstand voltage (1.2/50µS) kv peak 75 One minute 50Hz withstand voltage kv rms 28 3 DESIGN DETAIL 3.1 Transformer circuit 1)For Measuring Accuracy class 1.0 Rated burden VA Min 15 2) For Protection Accuracy class 5P10 Rated burden VA Min 15 3) For Differential Protection Accuracy class N.A. Rated burden VA N.A. Knee-point voltage 3.2 Bus circuit N.A. Equipment s Should Comply With AIS Technical Specifications Page 9 of 11

16 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification 1) Measuring winding Accuracy class 1.0 Rated burden VA Min 15 2) Protection winding Accuracy class 5P10 Rated burden VA Min Outgoing feeder & Capacitor Bank feeder 1) For Measuring Accuracy class 1.0 Rated burden VA Min 15 2) For Protection Accuracy class 5P10 Rated burden VA Min Aux. Transformer circuit 1) For Measuring Accuracy class N.A. Rated burden VA N.A. 2) For Protection Accuracy class N.A. Rated burden VA N.A. E VOLTAGE TRANSFORMERS 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type Molded type Equipment s Should Comply With AIS Technical Specifications Page 10 of 11

17 Technical Particulars and Guarantees of 11 kv Metal Clad Switchgear No. Description Unit Specification Indoor with drawable 1.4 Model To be filled in 1.5 Applicable Standards IEC Number of phases Single phase x 3 2 ELECTRICAL DATA 2.1 Rated primary voltage kv 11 / Rated secondary voltage V 110 / Rated tertiary voltage for open delta winding for earth fault indication 2.4 Rated voltage factor V 110 /3 For continuous 1.2 For 8 hours Rated insulation level Impulse withstand voltage (1.2/50µs) kv peak 75 One minute 50Hz withstand voltage kv rms Fuse protection Rated primary side A To be filled in Rated secondary side A To be filled in 3 DESIGN DETAIL 3.1 Accuracy class 1.0/3P 3.2 Ratio error % To be filled in 3.3 Rated burden VA Min Temperature rise limit at rated primary To be filled in voltage 3.5 Phase displacement min To be filled in Note: Switchgear enclosure and Circuit breaker should be from same manufacturer. o C Equipment s Should Comply With AIS Technical Specifications Page 11 of 11

18 100 AMolded Case Circuit Breaker 100 A Molded Case Circuit Breaker No Description Unit UNDP Offered 1 Reference standard IEC 2 Manufacturer Schneider, ABB, Siemens or equivalent. 3 Manufacturer type designation To be Filled 4 Country of manufacturer To be Filled 5 Standard IEC Ambient operation Temperature C -25 to Rated voltages: - Insulation Voltage (UI). - Impulse withstand voltage (UImp). - Operational Voltage (Ue). V kv V No. of Poles 3 9 Frame Size A Rated Current (Ir) A Rated interrupting current ka Rated frequency Hz Trip Units: - TMD/THA - MA - Electronic Yes Yes Yes/No 14 Durability (No. of Operation): C/O Indication Contacts Yes 16 Connections: - Fixed. Fixed - Withdrawable. 17 Overall dimension (width/depth/height) mm To be Filled 18 Total weight kg To be Filled 19 Catalogue and Certificates To be Submitted Page 1 of 1

19 110V Battery and Battery Charger 110V Battery and Battery Charger No. Description Unit Specification A BATTERIES 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type Pocket-plate Hidischarge type Nickel-Cadmium 1.4 Model To be filled in 1.5 Applicable Standards 2 DESIGN DETAIL 2.1 Rated capacity for 10 hours rate (To be confirmed calculation Report) AH IEEE1115for calculation, IEC60623,for equipment Rated voltage of battery V Nominal charging rate current A To be filled in 2.4 Nominal voltage of battery cell V/cell Number of cells Type of electrolyte 2.7 Type of mounting rack 3 DIMENSION AND WEIGHT Potassium hydroxide Steel painted trays with antiacid coating 3.1 Over all dimension of batteries on rack (W x L x H) m To be filled in 3.2 Weight of cell with electrolyte Kg/ cell To be filled in Page 1 of 4

20 110V Battery and Battery Charger B No. Description Unit BATTERY CHARGERS Specification 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type of battery charger 1.4 Type of rectifier Full automatic constant voltage DC power source Single phase Thyristor full wave bridge 1.5 Type of cooling for rectifier Self-air-cooled 1.6 Model To be filled in 1.7 Applicable Standards IEC , -2, Degree of protection IP Number of chargers 2x100% for battery 2 ELECTRICAL DATA 2.1 Rated input AC voltage V 230±10% 2.2 Rated Frequency Hz Regulated voltage range on DC busbar (Automatic Voltage regulator) Means of regulating output voltage on DC busbar 2.5 Di-electric strength (50Hz for 1 minute) V 110 V ±10% Semi-conductor dropper Between AC phases and earth V 2000 Between AC and DC circuit V DESIGN DETAIL 3.1 Continuous rated output current including the de rating factor On float mode A To be filled in Page 2 of 4

21 110V Battery and Battery Charger No. Description Unit Specification On boost mode A To be filled in 3.2 Charger rate output voltage Float Charging V To be filled in Boost Charging V To be filled in 3.3 Voltage ripple % To be filled in 3.4 Type of charger Cubicle 4 DIMENSION AND WEIGHT 4.1 Overall dimensions of Cubicle (L x W x H) m Air-insulated metalenclosed t To be filled in 4.2 Total weight of battery charger kg To be filled in C 110 V D.C. SWITCHBOARD 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type To be filled in 1.4 Model To be filled in 1.5 Location of services Indoor 1.6 Degree of protection IP 41 2 ELECTRICAL DATA 2.1 Rated DC voltage V Rated current of busbars at 55 C ambient temperature A To be filled in 2.3 Main isolator rating A To be filled in 2.4 Main fuse rating A To be filled in 3 DESIGN DETAIL A MCCB (Incomings & Bus Coupler) Page 3 of 4

22 110V Battery and Battery Charger No. Description Unit Specification 3.1 Applicable Standards IEC Site current rating (at 55 C) A To be filled in 3.3 Rated short time current (3 s) ka To be filled in 3.4 Protection Thermal & Magnetic B DETAILS OF EARTH FAULT PROTECTION 1.1 Manufacturer Name To be filled in 1.2 Type To be filled in 1.3 Model To be filled in C DETAILS OF UNDER VOLTAGE PROTECTION 1.1 Manufacturer Name To be filled in 1.2 Type To be filled in 1.3 Model To be filled in D INSTRUMENTS 1.1 Manufacturer Name To be filled in 1.2 Type of meter Voltmeter Ammeter To be filled in To be filled in 4 DIMENSION AND WEIGHT 4.1 Overall dimensions of Switchboard (L x W x H) m To be filled in 4.2 Total weight of Switchboard kg To be filled in Page 4 of 4

23 160 AMolded Case Circuit Breaker 160 A Molded Case Circuit Breaker No Description Unit UNDP Offered 1 Reference standard IEC 2 Manufacturer Schneider, ABB, Siemens or equivalent. 3 Manufacturer type designation To be Filled 4 Country of manufacturer To be Filled 5 Standard IEC Ambient operation Temperature C -25 to Rated voltages: - Insulation Voltage (UI). - Impulse withstand voltage (UImp). - Operational Voltage (Ue). V kv V No. of Poles 3 9 Frame Size A Rated Current (Ir) A Rated interrupting current ka Rated frequency Hz Trip Units: - TMD/THA - MA - Electronic Yes Yes Yes/No 14 Durability (No. of Operation): C/O Indication Contacts Yes 16 Connections: - Fixed. Fixed - Withdrawable. 17 Overall dimension (width/depth/height) mm To be Filled 18 Total weight kg To be Filled 19 Catalogue and Certificates To be Submitted Page 1 of 1

24 250 AMolded Case Circuit Breaker 250 A Molded Case Circuit Breaker No Description Unit UNDP Offered 1 Reference standard IEC 2 Manufacturer Schneider, ABB, Siemens or equivalent. 3 Manufacturer type designation To be Filled 4 Country of manufacturer To be Filled 5 Standard IEC Ambient Operation Temperature C -25 to Rated voltages: - Insulation Voltage (UI). - Impulse withstand voltage (UImp). - Operational Voltage (Ue). V kv V No. of Poles 3 9 Frame Size A Rated Current (Ir) A Rated interrupting current ka Rated frequency Hz Trip Units: - TMD/THA - MA - Electronic Yes Yes Yes/No 14 Durability (No. of Operation): C/O Indication Contacts Yes 16 Connections: - Fixed. Fixed - Withdrawable. 17 Overall dimension (width/depth/height) mm To be Filled 18 Total weight kg To be Filled 19 Catalogue and Certificates To be Submitted Page 1 of 1

25 1000kVA 11/0.416kV Transformer Technical Particulars and Guarantees of 1000kVA, 11/0.416kV Transformer No. Description Unit Specification 1 GENERAL 1.1 Manufacturer Name SEA, ABB, Siemens, BEST, Schneider, MATELEC or equivalent 1.2 Country of Manufacturing 1.3 Type Oil immersed cable box for both H.V & L.V 1.4 Model To be filled in 1.5 Applicable Standards IEC Location of service Outdoor 1.7 Type Tests and Short circuit Test Report Certificate Provided Yes 2 RATINGS 2.1 Rated power kva Rated voltage ratio Primary kv 11(±2 x 2.5%) Secondary kv 0.416Y/ Number of phase Frequency Hz Vector group symbol Dyn Cooling method ONAN 2.7 No load losses kw 2.8 Load loss at full load at 75 deg temperature kw 2.9 Maximum temperature rise at rated power Top oil by thermometer K 45 Winding by resistance K 50 Page 1 of 2

26 Technical Particulars and Guarantees of 1000kVA, 11/0.416kV Transformer Specification Description Unit No. Hot spot of winding K To be filled in 2.10 Impedance voltage at continuous rated power % 6 3 Rated insulation level for Primary Impulse withstand voltage kv (1.2/50µS) peak 75 One minute 50Hz withstand voltage kv rms 28 4 DESIGN DETAILS 4.1 Off-load tap changer Tapping range (±2 x 2.5%) Tapping step 2.50% 4.2 Type of oil (As per IEC requirement) SHELL DIALA B 5 DIMENSION AND WEIGHT 5.1 Dimension of Transformer (L x W x H) mm To be filled in 5.2 Total oil required(volume) Liter To be filled in 5.3 Total weight of complete transformer including fitting and oil kg To be filled in Page 2 of 2

27 1250A Air Circuit Breakers 1250A Air Circuit Breakers No Description Unit UNDP Offered 1 Reference standard IEC 2 Manufacturer Schneider, ABB, Siemens or equivalent. 3 Manufacturer type designation 4 Country of manufacturer 5 Rated service voltage (Ue) V Rated impulse withstand voltage kv 12 7 Rated uninterrupted current A Rated frequency Hz 50 9 Rated duty Uninterrupted 10 Breaking capacity ka Making capacity ka Rated short circuit withstand current /1sec ka 85 Design features: a) Number of poles 3 b) Stored energy operation Yes c) Method if installation Fixed d) Rated supply control circuit V 110 VDC e) Type of release shunt and adjustable over-current f) Closing and opening posh button Yes g) Protection Relay Yes 13 g) Auxiliary contacts 4 NO + 4 NC 14 Overall dimension mm (width/depth/height) 15 Total weight kg Page 1 of 1

28 1600A Air Circuit Breakers 1600A Air Circuit Breakers No Description Unit UNDP Offered 1 Reference standard IEC 2 Manufacturer Schneider, ABB, Siemens or equivalent. 3 Manufacturer type designation 4 Country of manufacturer 5 Rated service voltage (Ue) V Rated impulse withstand voltage kv 12 7 Rated uninterrupted current A Rated frequency Hz 50 9 Rated duty Uninterrupted 10 Breaking capacity ka Making capacity ka Rated short circuit withstand current /1sec ka 30 Design features: a) Number of poles 3 b) Stored energy operation Yes c) Method if installation Fixed d) Rated supply control circuit V 110 VDC e) Type of release shunt and adjustable over-current f) Closing and opening posh button Yes g) Protection Relay Yes 13 g) Auxiliary contacts 4 NO + 4 NC 14 Overall dimension mm (width/depth/height) 15 Total weight kg Page 1 of 1

29 2000A Air Circuit Breakers 2000A Air Circuit Breakers No Description Unit UNDP Offered 1 Reference standard IEC 2 Manufacturer Schneider, ABB, Siemens or equivalent. 3 Manufacturer type designation 4 Country of manufacturer 5 Rated service voltage (Ue) V Rated impulse withstand voltage kv 12 7 Rated uninterrupted current A Rated frequency Hz 50 9 Rated duty Uninterrupted 10 Breaking capacity ka Making capacity ka Rated short circuit withstand current /1sec ka 65 Design features: a) Number of poles 3 b) Stored energy operation Yes c) Method if installation withdrawal d) Rated supply control circuit V 110 VDC e) Type of release shunt and adjustable over-current f) Closing and opening posh button Yes g) Protection Relay Yes 13 g) Auxiliary contacts 4 NO + 4 NC 14 Overall dimension mm (width/depth/height) 15 Total weight kg Page 1 of 1

30 5000A Air Circuit Breakers 5000A Air Circuit Breakers No Description Unit UNDP Offered 1 Reference standard IEC 2 Manufacturer Schneider, ABB, Siemens or equivalent. 3 Manufacturer type designation 4 Country of manufacturer 5 Rated service voltage (Ue) V Rated impulse withstand voltage kv 12 7 Rated uninterrupted current A Rated frequency Hz 50 9 Rated duty Uninterrupted 10 Breaking capacity ka Making capacity ka Rated short circuit withstand current /1sec ka 100 Design features: a) Number of poles 3 b) Stored energy operation Yes c) Method if installation withdrawal d) Rated supply control circuit V 110 VDC e) Type of release shunt and adjustable over-current f) Closing and opening posh button Yes g) Protection Relay Yes 13 g) Auxiliary contacts 4 NO + 4 NC 14 Overall dimension mm (width/depth/height) 15 Total weight kg Page 1 of 1

31 DC Distribution Panel Technical Particulars and Guarantees of DC Distribution Panel No. Description Unit Specification 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type Metal-clad totally enclosed 1.4 Model To be filled in 1.5 Applicable Standards IEC 1.6 Location of services Indoor 1.7 Degree of protection IP 41 2 ELECTRICAL DATA 2.1 Rated AC voltage V 110 VDC 2 wires 2.2 Power frequency withstand test voltage KVrms Rated short circuit current, 1sec. KA 30 3 DESIGN DETAIL B BUSBAR 2.1 Rated current of busbars at 55 C ambient temperature A To be filled in 2.2 Busbar cross section mm2 To be filled in 2.3 Busbar insulation material To be filled in C DETAILS OF MCBs 1.1 Manufacturer Name To be filled in 1.2 Type Molded Case 1.3 Model To be filled in 1.4 Applicable Standards IEC Site current rating (at 55 C) A To be filled 1.6 Rated short time current (3 s) ka To be filled Typical circuit diagram number To be filled 1.8 Protection Thermal & Magnetic Page 1 of 2

32 Technical Particulars and Guarantees of LV AC Distribution Panel No. Description Unit Specification D DETAILS OF UNDER VOLTAGE PROTECTION 1.1 Manufacturer Name To be filled in 1.2 Type To be filled in 1.3 Model To be filled in 1.4 Catalogue Provided Yes E INSTRUMENTS 1.1 Manufacturer Name To be filled in 1.2 Type of meter Voltmeter To be filled in Ammeter To be filled in 1.3 Catalogue Provided Yes F Single line diagram & Arrangement drawing number To be filled in 4 DIMENSION AND WEIGHT Overall dimensions of Distribution Panel m To be filled in (L x W x H) Total weight of Distribution Panel kg To be filled in Page 2 of 2

33 Handling Tool No. Description 1 GENERAL Handling Tool 1.1 Manufacturer Name SK, Proto or Beta 1.2 Country of Manufacturing Origin 1.3 Type Hand Tools 2 CONTENT Roller Cab - Eight drawers (588x367 mm) with ball bearing slides: 6 drawers, 70 mm high 2 drawers, 140 mm high - Drawer bases protected by foamed rubber mats. - Four castors 125 mm in Ø: fixed and 2 steering (one with brake). 1 Set - Front centralized safety lock. - Opening system throughout length of drawer. - Static load capacity: 1200 kg. - Thermoplastic worktop. - Integrated side and rear bottle holders. - Integrated paper roll holder. - Uprights and drawer front made of aluminum. 2.2 Metric T-Handle Hex Key Wrench Set 1 Set Torx Head Screwdrivers Set. 1 Set 2.3 Set of Combination Wrenches (6-32) 1 Set 2.4 Set of socket Driver (20 sockets +6 1 Set Hexagon accessories + adapters) 1 Set Bi-Hex 2.5 Heavy Duty Scissors 1 pc Page 1 of 2 Specification

34 2.6 Knife with 5 trapezoidal blades 1 pc 2.7 AC-Steel wire Brush 1 pc 2.8 Hacksaw Frame 1 pc 2.9 Universal cut flat files 2 pcs 2.10 Sledge hammers fiber shafts, 1pc (4kg) & 1pc (1 kg), Claw Hammer wooden shaft 1pc (300g) 2.11 Screwdrivers Steel Head Cross and slotted type (Different sizes) 2 Set 2.12 Set of 8 Micro-Screwdrivers 1 Set Pliers: - Combination Pliers. - Extra-long Needle Nose pliers. - Long Bent Needle Nose Pliers Heavy Duty Diagonal cutting nippers. - Adjustment self-locking pliers. - External Circlip Pliers (Flat, 45 and 90 ). - Water pump Pliers. 1 pc 1pc 1pc 1pc 1pc 1pc from each 2pc 2.14 Double ended socked wrenches (6*6-21*21) 1 Set 2.15 Set of Driver Reversible Ratchet (2.5-14)+ Accessories+ Adapters 1 Set 2.16 Click Type Torque Wrench. 1 pc 2.17 Heavy Duty Pipe Wrenches Light. 6 Different sizes 2.18 Swivel End Ratcheting Combination Wrenches ( ). 1pc from each 2.19 Adjustable Wrenches 6 +Scales. 5 Different sizes 2.20 Set of Double offset ring Wrenches (7-22). 1 Set 2.21 Set of Double open end Wrenches (7-32). 1 Set 2.22 Measuring Tape (10m) 1pc 2.23 Special Tools for Substation Maintenance (if any) 1 PC 3 DOCUMENTS 3.1 Catalogues To be Submitted Page 2 of 2

35 Laptop/HP ProBook 650 G2 Notebook PC (ENERGY STAR) Technical Particulars and Guarantees of Laptop No. Description Unit Specification 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Color Shadow mesh cover, twinkle black base 2 Specification 2.1 Operating System Windows 2.2 Copy of operating system Original Windows 10 32/64bit 2.3 Processor family 6th Generation Intel Core i7 processor Processor Chipset Memory Intel Core i7-6600u with Intel HD Graphics 520 (2.6 GHz, up to 3.4 GHz with Intel Turbo Boost Technology, 4 MB cache, 2 cores) Chipset is integrated with processor 16 GB DDR SDRAM (2 x 8 GB) 2.7 Memory slots 2 SODIMM 2.8 Internal drive 256 GB M.2 SATA TLC SSD 2.9 Optical drive DVD+/-RW SuperMulti DL 2.10 Display 15.6" diagonal FHD SVA antiglare slim LED-backlit (1920 x 1080) 2.11 Graphics Intel HD Graphics Ports 1 USB 3.0; 1 USB 3.0 charging; 1 USB Type-C ; 1 DisplayPort; 1 VGA; 1 headphone/microphone combo; 1 AC power; 1 RJ-45; 1 docking connector; 1 serial port 2.13 Expansion slots Supports SD, SDHC, SDXC. 1 Page 1 of 2

36 media card reader 2.14 Audio HD audio with DTS Studio Sound ; two integrated stereo speakers; Dual array microphones; Headphone and microphone combo jack HD audio with DTS Studio Sound ; two integrated stereo speakers; Dual array microphones; Headphone and microphone combo jack 2.15 Integrated camera 720p HD webcam 2.16 Keyboard Premium Spill-Resistant Keyboard/ Arabic Keyboard 2.17 Pointing device Touchpad with on/off button, supports 2-way scroll, taps and gestures enabled by default, two-finger scrolling, two finger zoom (pinch) 2.18 Wireless Intel a/b/g/n (2x2) and Bluetooth 4.2 Combo 2.19 Power supply 45 W Smart AC adapter; 65 W Smart AC adapter; 90 W Smart adapter 2.20 Battery Long Life 3-cell, 48 Wh Li-ion prismatic 2.21 Battery life 3-cell, 48 Wh Li-ion: up to 10 hours and 15 minutes 2.22 Dimensions (W X D X H) x x 1.07 in 2.23 Weight To Be Filled 2.24 Warranty 1 Year 2.25 Additional 1- Baggage 2- Wireless mouse Security Management Security lock slot + Finger Print reader Page 2 of 2

37 Low Voltage power Cables 240mm 2 Technical Particulars and Guarantees of Low Voltage power Cables 240mm 2 No. Description Unit Specification 1 GENERAL 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type 1.4 Rated voltage (Uo/U) kv 600/1000 Page 1 of 2 (According to MoE specifications) 1.5 Applicable Standards IEC 60502, IEC 60183, IEC 60228, IEC 60287,, IEC 60287, IEC 60811, IEC 60853, 1.6 Type Test Certificate Yes 2 ELECTRICAL DATA 2.1 Rated Frequency Hz AC. Withstand voltage for 5 minutes kv rms Max. DC Conductor resistance at 20 C ohm/km Temperature range C -15 to CABLE DATA 3.1 Number of conductor Core Single 3.2 Cross sectional area (Phase) Stranded and Compacted mm Shape of conductor 3.4 Material of Conductor Cu. 3.5 Material of insulation XLPE 3.6 Insulation thickness (Nominal) mm Material of sheath PVC Compacted circular stranded 3.8 Nominal Thickness of over sheath (Approx.) mm To be filled in 3.9 Insulation resistance between core / screen MOhm To be filled in 3.10 Color of sheath Black 3.11 Type of chemical treatment against To be filled in

38 termite in the outer sheath Rated short-time current for 1 sec. ka Overall diameter of cable (Approx.) mm Net weight (Approx.) kg/km To be filled in 4 DOCUMENTS 4.1 Cross section drawing and details of cable layers and catalogues, Includes To be Submitted catalogues for Cable Terminations 4.2 Type test reports To be Submitted Page 2 of 2

39 LV AC Distribution Panel Technical Particulars and Guarantees of LV AC Distribution Panel No. Description 1 GENERAL Unit Specification 1.1 Manufacturer Name To be filled in 1.2 Country of Manufacturing To be filled in 1.3 Type Metal-clad totally enclosed 1.4 Model To be filled in 1.5 Applicable Standards IEC Location of services Indoor 1.7 Degree of protection IP 41 2 ELECTRICAL DATA 2.1 Rated AC voltage V 400/230V, 3phase 4 wires 2.2 Power frequency withstand test voltage KVrms Rated short circuit current, 1sec. KA Control supply voltage Trip and closing coil V DC110 Spring charging motors V DC110 3 DESIGN DETAIL A AIR BREAK CIRCUIT BREAKER (INCOMING) 1.1 Manufacturer Name To be filled in 1.2 Type ACB 1.3 Model To be filled in 1.4 Applicable Standards IEC Rated current A 5000 Equipment s Should Comply with AIS Technical Specifications. Page 1 of 2

40 Technical Particulars and Guarantees of LV AC Distribution Panel Specification No. Description Unit 1.6 Protection Numerical,Ther mal & Magnetic B 2.1 BUSBAR Rated current of busbars at 55 C ambient temperature A Busbar cross section mm 2 To be filled in 2.3 Busbar insulation material To be filled in C DETAILS OF MCCBs 1.1 Manufacturer Name To be filled in 1.2 Type Molded Case 1.3 Model To be filled in 1.4 Applicable Standards IEC Thermal & 1.8 Protection Magnetic D DETAILS OF UNDER VOLTAGE PROTECTION 1.1 Manufacturer Name To be filled in 1.2 Type To be filled in 1.3 Model To be filled in E INSTRUMENTS 1.1 Manufacturer Name To be filled in 1.2 Type of meter F Multi-Function meter Single line diagram & Arrangement drawing number 4 DIMENSION AND WEIGHT Overall dimensions of Distribution Panel(L x W x H) m To be filled in To be filled in To be filled in Total weight of Distribution Panel kg To be filled in Equipment s Should Comply with AIS Technical Specifications. Page 2 of 2